riscv: dts: Sync to Linux Kernel ae350 dts.
PATCH 1/1 riscv: dts: Sync to Linux Kernel ae350 dts.
From: Rick Chen <[email protected]>
Use same dts to boot U-Boot and Kernel.
Following are the change notes :
1 Remove early printk bootargs.
2 Timer frequency are changed to 60MHz.
3 Add dma, snd, lcd, virtio nodes which are used
in kernel drivers. They does not been used by U-Boot.
4 Change spi irq from 3 to 4.
--- arch/riscv/dts/ae350.dts | 107 ++++++++++++++++++++++++++++++++++++++++------- 1 file changed, 92 insertions(+), 15 deletions(-)
arch/riscv/dts/ae350.dts +92 -15
@@ -12,15 +12,14 @@ }; chosen { - bootargs = "console=ttyS0,38400n8 earlyprintk=uart8250-32bit,0xf0300000 debug loglevel=7"; + bootargs = "console=ttyS0,38400n8 debug loglevel=7"; stdout-path = "uart0:38400n8"; }; cpus { #address-cells = <1>; #size-cells = <0>; - timebase-frequency = <10000000>; - + timebase-frequency = <60000000>; CPU0: cpu at 0 { device_type = "cpu"; reg = <0>;
@@ -29,7 +28,8 @@ riscv,isa = "rv64imafdc"; mmu-type = "riscv,sv39"; clock-frequency = <60000000>; - + d-cache-size = <0x8000>; + d-cache-line-size = <32>; CPU0_intc: interrupt-controller { #interrupt-cells = <1>; interrupt-controller;
@@ -48,13 +48,6 @@ #size-cells = <2>; compatible = "andestech,riscv-ae350-soc"; ranges; - }; - - plmt0 at e6000000 { - compatible = "riscv,plmt0"; - interrupts-extended = <&CPU0_intc 7>; - reg = <0x0 0xe6000000 0x0 0x100000>; - }; plic0: interrupt-controller at e4000000 { compatible = "riscv,plic0";
@@ -62,7 +55,7 @@ #interrupt-cells = <2>; interrupt-controller; reg = <0x0 0xe4000000 0x0 0x2000000>; - riscv,ndev=<31>; + riscv,ndev=<71>; interrupts-extended = <&CPU0_intc 11 &CPU0_intc 9>; };
@@ -76,6 +69,13 @@ interrupts-extended = <&CPU0_intc 3>; }; + plmt0 at e6000000 { + compatible = "riscv,plmt0"; + interrupts-extended = <&CPU0_intc 7>; + reg = <0x0 0xe6000000 0x0 0x100000>; + }; + }; + spiclk: virt_100mhz { #clock-cells = <0>; compatible = "fixed-clock";
@@ -85,7 +85,7 @@ timer0: timer at f0400000 { compatible = "andestech,atcpit100"; reg = <0x0 0xf0400000 0x0 0x1000>; - clock-frequency = <40000000>; + clock-frequency = <60000000>; interrupts = <3 4>; interrupt-parent = <&plic0>; };
@@ -119,11 +119,89 @@ interrupt-parent = <&plic0>; }; + dma0: dma at f0c00000 { + compatible = "andestech,atcdmac300"; + reg = <0x0 0xf0c00000 0x0 0x1000>; + interrupts = <10 4 64 4 65 4 66 4 67 4 68 4 69 4 70 4 71 4>; + dma-channels = <8>; + interrupt-parent = <&plic0>; + }; + + lcd0: lcd at e0200000 { + compatible = "andestech,atflcdc100"; + reg = <0x0 0xe0200000 0x0 0x1000>; + interrupts = <20 4>; + interrupt-parent = <&plic0>; + }; + smc0: smc at e0400000 { compatible = "andestech,atfsmc020"; reg = <0x0 0xe0400000 0x0 0x1000>; }; + snd0: snd at f0d00000 { + compatible = "andestech,atfac97"; + reg = <0x0 0xf0d00000 0x0 0x1000>; + interrupts = <17 4>; + interrupt-parent = <&plic0>; + }; + + virtio_mmio at fe007000 { + interrupts = <0x17 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe007000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe006000 { + interrupts = <0x16 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe006000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe005000 { + interrupts = <0x15 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe005000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe004000 { + interrupts = <0x14 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe004000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe003000 { + interrupts = <0x13 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe003000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe002000 { + interrupts = <0x12 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe002000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe001000 { + interrupts = <0x11 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe001000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe000000 { + interrupts = <0x10 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe000000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + nor at 0,0 { compatible = "cfi-flash"; reg = <0x0 0x88000000 0x0 0x1000>;
@@ -138,9 +216,8 @@ #size-cells = <0>; num-cs = <1>; clocks = <&spiclk>; - interrupts = <3 4>; + interrupts = <4 4>; interrupt-parent = <&plic0>; - flash at 0 { compatible = "spi-flash"; spi-max-frequency = <50000000>;
Signature · 1 line
2.7.4
PATCH 1/1 riscv: dts: Sync to Linux Kernel ae350 dts.
Hi Rick,
Quoted 173 lines · Andes
From: Rick Chen <[email protected]>
Use same dts to boot U-Boot and Kernel.
Following are the change notes :
1 Remove early printk bootargs.
2 Timer frequency are changed to 60MHz.
3 Add dma, snd, lcd, virtio nodes which are used
in kernel drivers. They does not been used by U-Boot.
4 Change spi irq from 3 to 4.Signed-off-by Rick Chen <[email protected]>Cc Greentime Hu <[email protected]>--- arch/riscv/dts/ae350.dts | 107 ++++++++++++++++++++++++++++++++++++++++------- 1 file changed, 92 insertions(+), 15 deletions(-)arch/riscv/dts/ae350.dts +81
-13@@ -12,15 +12,14 @@ }; chosen { - bootargs = "console=ttyS0,38400n8 earlyprintk=uart8250-32bit,0xf0300000 debug loglevel=7"; + bootargs = "console=ttyS0,38400n8 debug loglevel=7"; stdout-path = "uart0:38400n8"; }; cpus { #address-cells = <1>; #size-cells = <0>; - timebase-frequency = <10000000>; - + timebase-frequency = <60000000>; CPU0: cpu at 0 { device_type = "cpu"; reg = <0>;@@ -29,7 +28,8 @@ riscv,isa = "rv64imafdc"; mmu-type = "riscv,sv39"; clock-frequency = <60000000>; - + d-cache-size = <0x8000>; + d-cache-line-size = <32>; CPU0_intc: interrupt-controller { #interrupt-cells = <1>; interrupt-controller;@@ -48,13 +48,6 @@ #size-cells = <2>; compatible = "andestech,riscv-ae350-soc"; ranges; - }; - - plmt0 at e6000000 { - compatible = "riscv,plmt0"; - interrupts-extended = <&CPU0_intc 7>; - reg = <0x0 0xe6000000 0x0 0x100000>; - }; plic0: interrupt-controller at e4000000 { compatible = "riscv,plic0";@@ -62,7 +55,7 @@ #interrupt-cells = <2>; interrupt-controller; reg = <0x0 0xe4000000 0x0 0x2000000>; - riscv,ndev=<31>; + riscv,ndev=<71>; interrupts-extended = <&CPU0_intc 11 &CPU0_intc 9>; };@@ -76,6 +69,13 @@ interrupts-extended = <&CPU0_intc 3>; }; + plmt0 at e6000000 { + compatible = "riscv,plmt0"; + interrupts-extended = <&CPU0_intc 7>; + reg = <0x0 0xe6000000 0x0 0x100000>; + }; + }; + spiclk: virt_100mhz { #clock-cells = <0>; compatible = "fixed-clock";@@ -85,7 +85,7 @@ timer0: timer at f0400000 { compatible = "andestech,atcpit100"; reg = <0x0 0xf0400000 0x0 0x1000>; - clock-frequency = <40000000>; + clock-frequency = <60000000>; interrupts = <3 4>; interrupt-parent = <&plic0>; };@@ -119,11 +119,89 @@ interrupt-parent = <&plic0>; }; + dma0: dma at f0c00000 { + compatible = "andestech,atcdmac300"; + reg = <0x0 0xf0c00000 0x0 0x1000>; + interrupts = <10 4 64 4 65 4 66 4 67 4 68 4 69 4 70 4 71 4>; + dma-channels = <8>; + interrupt-parent = <&plic0>; + }; + + lcd0: lcd at e0200000 { + compatible = "andestech,atflcdc100"; + reg = <0x0 0xe0200000 0x0 0x1000>; + interrupts = <20 4>; + interrupt-parent = <&plic0>; + }; + smc0: smc at e0400000 { compatible = "andestech,atfsmc020"; reg = <0x0 0xe0400000 0x0 0x1000>; }; + snd0: snd at f0d00000 { + compatible = "andestech,atfac97"; + reg = <0x0 0xf0d00000 0x0 0x1000>; + interrupts = <17 4>; + interrupt-parent = <&plic0>; + }; + + virtio_mmio at fe007000 { + interrupts = <0x17 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe007000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe006000 { + interrupts = <0x16 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe006000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe005000 { + interrupts = <0x15 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe005000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe004000 { + interrupts = <0x14 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe004000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe003000 { + interrupts = <0x13 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe003000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe002000 { + interrupts = <0x12 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe002000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe001000 { + interrupts = <0x11 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe001000 0x0 0x1000>;
arch/riscv/dts/ae350.dts line 204
Quoted 10 lines
arch/riscv/dts/ae350.dts +10
-0+ compatible = "virtio,mmio"; + }; + + virtio_mmio at fe000000 { + interrupts = <0x10 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe000000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; +
Do these virtio devices exist on the real hardware?
Quoted 5 lines
arch/riscv/dts/ae350.dts +0
-0nor at 0,0 { compatible = "cfi-flash"; reg = <0x0 0x88000000 0x0 0x1000>;@@ -138,9 +216,8 @@ #size-cells = <0>;
arch/riscv/dts/ae350.dts
Quoted 10 lines
arch/riscv/dts/ae350.dts +1
-3num-cs = <1>; clocks = <&spiclk>; - interrupts = <3 4>; + interrupts = <4 4>; interrupt-parent = <&plic0>; - flash at 0 { compatible = "spi-flash"; spi-max-frequency = <50000000>; --
Regards,
Bin
PATCH 1/1 riscv: dts: Sync to Linux Kernel ae350 dts.
Bin Meng <[email protected]> 於 2018年10月8日 週一 下午1:49寫道:
Quoted 181 lines
Hi Rick,
Quoted 177 lines · Andes
From: Rick Chen <[email protected]>
Use same dts to boot U-Boot and Kernel.
Following are the change notes :
1 Remove early printk bootargs.
2 Timer frequency are changed to 60MHz.
3 Add dma, snd, lcd, virtio nodes which are used
in kernel drivers. They does not been used by U-Boot.
4 Change spi irq from 3 to 4.Signed-off-by Rick Chen <[email protected]>Cc Greentime Hu <[email protected]>--- arch/riscv/dts/ae350.dts | 107 ++++++++++++++++++++++++++++++++++++++++------- 1 file changed, 92 insertions(+), 15 deletions(-)arch/riscv/dts/ae350.dts +85
-13@@ -12,15 +12,14 @@ }; chosen { - bootargs = "console=ttyS0,38400n8 earlyprintk=uart8250-32bit,0xf0300000 debug loglevel=7"; + bootargs = "console=ttyS0,38400n8 debug loglevel=7"; stdout-path = "uart0:38400n8"; }; cpus { #address-cells = <1>; #size-cells = <0>; - timebase-frequency = <10000000>; - + timebase-frequency = <60000000>; CPU0: cpu at 0 { device_type = "cpu"; reg = <0>;@@ -29,7 +28,8 @@ riscv,isa = "rv64imafdc"; mmu-type = "riscv,sv39"; clock-frequency = <60000000>; - + d-cache-size = <0x8000>; + d-cache-line-size = <32>; CPU0_intc: interrupt-controller { #interrupt-cells = <1>; interrupt-controller;@@ -48,13 +48,6 @@ #size-cells = <2>; compatible = "andestech,riscv-ae350-soc"; ranges; - }; - - plmt0 at e6000000 { - compatible = "riscv,plmt0"; - interrupts-extended = <&CPU0_intc 7>; - reg = <0x0 0xe6000000 0x0 0x100000>; - }; plic0: interrupt-controller at e4000000 { compatible = "riscv,plic0";@@ -62,7 +55,7 @@ #interrupt-cells = <2>; interrupt-controller; reg = <0x0 0xe4000000 0x0 0x2000000>; - riscv,ndev=<31>; + riscv,ndev=<71>; interrupts-extended = <&CPU0_intc 11 &CPU0_intc 9>; };@@ -76,6 +69,13 @@ interrupts-extended = <&CPU0_intc 3>; }; + plmt0 at e6000000 { + compatible = "riscv,plmt0"; + interrupts-extended = <&CPU0_intc 7>; + reg = <0x0 0xe6000000 0x0 0x100000>; + }; + }; + spiclk: virt_100mhz { #clock-cells = <0>; compatible = "fixed-clock";@@ -85,7 +85,7 @@ timer0: timer at f0400000 { compatible = "andestech,atcpit100"; reg = <0x0 0xf0400000 0x0 0x1000>; - clock-frequency = <40000000>; + clock-frequency = <60000000>; interrupts = <3 4>; interrupt-parent = <&plic0>; };@@ -119,11 +119,89 @@ interrupt-parent = <&plic0>; }; + dma0: dma at f0c00000 { + compatible = "andestech,atcdmac300"; + reg = <0x0 0xf0c00000 0x0 0x1000>; + interrupts = <10 4 64 4 65 4 66 4 67 4 68 4 69 4 70 4 71 4>; + dma-channels = <8>; + interrupt-parent = <&plic0>; + }; + + lcd0: lcd at e0200000 { + compatible = "andestech,atflcdc100"; + reg = <0x0 0xe0200000 0x0 0x1000>; + interrupts = <20 4>; + interrupt-parent = <&plic0>; + }; + smc0: smc at e0400000 { compatible = "andestech,atfsmc020"; reg = <0x0 0xe0400000 0x0 0x1000>; }; + snd0: snd at f0d00000 { + compatible = "andestech,atfac97"; + reg = <0x0 0xf0d00000 0x0 0x1000>; + interrupts = <17 4>; + interrupt-parent = <&plic0>; + }; + + virtio_mmio at fe007000 { + interrupts = <0x17 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe007000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe006000 { + interrupts = <0x16 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe006000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe005000 { + interrupts = <0x15 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe005000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe004000 { + interrupts = <0x14 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe004000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe003000 { + interrupts = <0x13 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe003000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe002000 { + interrupts = <0x12 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe002000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe001000 { + interrupts = <0x11 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe001000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe000000 {
Quoted 8 lines
arch/riscv/dts/ae350.dts line 204
Quoted 6 lines
arch/riscv/dts/ae350.dts +6
-0+ interrupts = <0x10 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe000000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; +Do these virtio devices exist on the real hardware?
Hi Bin
No.
These virtio nodes does not exist on the read board. It is required on Andes' QEMU ae350 board.
Rick
Quoted 19 lines
Quoted 6 lines
arch/riscv/dts/ae350.dts +0
-0nor at 0,0 { compatible = "cfi-flash"; reg = <0x0 0x88000000 0x0 0x1000>;@@ -138,9 +216,8 @@ #size-cells = <0>;arch/riscv/dts/ae350.dts
Quoted 10 lines
arch/riscv/dts/ae350.dts +1
-3num-cs = <1>; clocks = <&spiclk>; - interrupts = <3 4>; + interrupts = <4 4>; interrupt-parent = <&plic0>; - flash at 0 { compatible = "spi-flash"; spi-max-frequency = <50000000>; --Regards,
Bin
PATCH 1/1 riscv: dts: Sync to Linux Kernel ae350 dts.
Hi Rick,
Quoted 192 lines · Rick Chen
Bin Meng <[email protected]> 於 2018年10月8日 週一 下午1:49寫道:
Quoted 181 lines
Hi Rick,
Quoted 177 lines · Andes
From: Rick Chen <[email protected]>
Use same dts to boot U-Boot and Kernel.
Following are the change notes :
1 Remove early printk bootargs.
2 Timer frequency are changed to 60MHz.
3 Add dma, snd, lcd, virtio nodes which are used
in kernel drivers. They does not been used by U-Boot.
4 Change spi irq from 3 to 4.Signed-off-by Rick Chen <[email protected]>Cc Greentime Hu <[email protected]>--- arch/riscv/dts/ae350.dts | 107 ++++++++++++++++++++++++++++++++++++++++------- 1 file changed, 92 insertions(+), 15 deletions(-)arch/riscv/dts/ae350.dts +85
-13@@ -12,15 +12,14 @@ }; chosen { - bootargs = "console=ttyS0,38400n8 earlyprintk=uart8250-32bit,0xf0300000 debug loglevel=7"; + bootargs = "console=ttyS0,38400n8 debug loglevel=7"; stdout-path = "uart0:38400n8"; }; cpus { #address-cells = <1>; #size-cells = <0>; - timebase-frequency = <10000000>; - + timebase-frequency = <60000000>; CPU0: cpu at 0 { device_type = "cpu"; reg = <0>;@@ -29,7 +28,8 @@ riscv,isa = "rv64imafdc"; mmu-type = "riscv,sv39"; clock-frequency = <60000000>; - + d-cache-size = <0x8000>; + d-cache-line-size = <32>; CPU0_intc: interrupt-controller { #interrupt-cells = <1>; interrupt-controller;@@ -48,13 +48,6 @@ #size-cells = <2>; compatible = "andestech,riscv-ae350-soc"; ranges; - }; - - plmt0 at e6000000 { - compatible = "riscv,plmt0"; - interrupts-extended = <&CPU0_intc 7>; - reg = <0x0 0xe6000000 0x0 0x100000>; - }; plic0: interrupt-controller at e4000000 { compatible = "riscv,plic0";@@ -62,7 +55,7 @@ #interrupt-cells = <2>; interrupt-controller; reg = <0x0 0xe4000000 0x0 0x2000000>; - riscv,ndev=<31>; + riscv,ndev=<71>; interrupts-extended = <&CPU0_intc 11 &CPU0_intc 9>; };@@ -76,6 +69,13 @@ interrupts-extended = <&CPU0_intc 3>; }; + plmt0 at e6000000 { + compatible = "riscv,plmt0"; + interrupts-extended = <&CPU0_intc 7>; + reg = <0x0 0xe6000000 0x0 0x100000>; + }; + }; + spiclk: virt_100mhz { #clock-cells = <0>; compatible = "fixed-clock";@@ -85,7 +85,7 @@ timer0: timer at f0400000 { compatible = "andestech,atcpit100"; reg = <0x0 0xf0400000 0x0 0x1000>; - clock-frequency = <40000000>; + clock-frequency = <60000000>; interrupts = <3 4>; interrupt-parent = <&plic0>; };@@ -119,11 +119,89 @@ interrupt-parent = <&plic0>; }; + dma0: dma at f0c00000 { + compatible = "andestech,atcdmac300"; + reg = <0x0 0xf0c00000 0x0 0x1000>; + interrupts = <10 4 64 4 65 4 66 4 67 4 68 4 69 4 70 4 71 4>; + dma-channels = <8>; + interrupt-parent = <&plic0>; + }; + + lcd0: lcd at e0200000 { + compatible = "andestech,atflcdc100"; + reg = <0x0 0xe0200000 0x0 0x1000>; + interrupts = <20 4>; + interrupt-parent = <&plic0>; + }; + smc0: smc at e0400000 { compatible = "andestech,atfsmc020"; reg = <0x0 0xe0400000 0x0 0x1000>; }; + snd0: snd at f0d00000 { + compatible = "andestech,atfac97"; + reg = <0x0 0xf0d00000 0x0 0x1000>; + interrupts = <17 4>; + interrupt-parent = <&plic0>; + }; + + virtio_mmio at fe007000 { + interrupts = <0x17 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe007000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe006000 { + interrupts = <0x16 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe006000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe005000 { + interrupts = <0x15 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe005000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe004000 { + interrupts = <0x14 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe004000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe003000 { + interrupts = <0x13 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe003000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe002000 { + interrupts = <0x12 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe002000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe001000 { + interrupts = <0x11 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe001000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe000000 {Quoted 8 lines
arch/riscv/dts/ae350.dts line 204
Quoted 6 lines
arch/riscv/dts/ae350.dts +6
-0+ interrupts = <0x10 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe000000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; +Do these virtio devices exist on the real hardware?
Quoted 6 lines
Hi Bin
No.
These virtio nodes does not exist on the read board. It is required on Andes' QEMU ae350 board.
So it is a special target, which matches some hardware components plus some "virtual" components like VirtIO?
BTW: where is the Linux AE350 DTS file? I do not see it in the Linux tree.
Regards,
Bin
PATCH 1/1 riscv: dts: Sync to Linux Kernel ae350 dts.
Bin Meng <[email protected]> 於 2018年10月16日 週二 上午9:43寫道:
Quoted 198 lines
Hi Rick,
Quoted 194 lines · Rick Chen
Bin Meng <[email protected]> 於 2018年10月8日 週一 下午1:49寫道:
Quoted 181 lines
Hi Rick,
Quoted 177 lines · Andes
From: Rick Chen <[email protected]>
Use same dts to boot U-Boot and Kernel.
Following are the change notes :
1 Remove early printk bootargs.
2 Timer frequency are changed to 60MHz.
3 Add dma, snd, lcd, virtio nodes which are used
in kernel drivers. They does not been used by U-Boot.
4 Change spi irq from 3 to 4.Signed-off-by Rick Chen <[email protected]>Cc Greentime Hu <[email protected]>--- arch/riscv/dts/ae350.dts | 107 ++++++++++++++++++++++++++++++++++++++++------- 1 file changed, 92 insertions(+), 15 deletions(-)arch/riscv/dts/ae350.dts +85
-13@@ -12,15 +12,14 @@ }; chosen { - bootargs = "console=ttyS0,38400n8 earlyprintk=uart8250-32bit,0xf0300000 debug loglevel=7"; + bootargs = "console=ttyS0,38400n8 debug loglevel=7"; stdout-path = "uart0:38400n8"; }; cpus { #address-cells = <1>; #size-cells = <0>; - timebase-frequency = <10000000>; - + timebase-frequency = <60000000>; CPU0: cpu at 0 { device_type = "cpu"; reg = <0>;@@ -29,7 +28,8 @@ riscv,isa = "rv64imafdc"; mmu-type = "riscv,sv39"; clock-frequency = <60000000>; - + d-cache-size = <0x8000>; + d-cache-line-size = <32>; CPU0_intc: interrupt-controller { #interrupt-cells = <1>; interrupt-controller;@@ -48,13 +48,6 @@ #size-cells = <2>; compatible = "andestech,riscv-ae350-soc"; ranges; - }; - - plmt0 at e6000000 { - compatible = "riscv,plmt0"; - interrupts-extended = <&CPU0_intc 7>; - reg = <0x0 0xe6000000 0x0 0x100000>; - }; plic0: interrupt-controller at e4000000 { compatible = "riscv,plic0";@@ -62,7 +55,7 @@ #interrupt-cells = <2>; interrupt-controller; reg = <0x0 0xe4000000 0x0 0x2000000>; - riscv,ndev=<31>; + riscv,ndev=<71>; interrupts-extended = <&CPU0_intc 11 &CPU0_intc 9>; };@@ -76,6 +69,13 @@ interrupts-extended = <&CPU0_intc 3>; }; + plmt0 at e6000000 { + compatible = "riscv,plmt0"; + interrupts-extended = <&CPU0_intc 7>; + reg = <0x0 0xe6000000 0x0 0x100000>; + }; + }; + spiclk: virt_100mhz { #clock-cells = <0>; compatible = "fixed-clock";@@ -85,7 +85,7 @@ timer0: timer at f0400000 { compatible = "andestech,atcpit100"; reg = <0x0 0xf0400000 0x0 0x1000>; - clock-frequency = <40000000>; + clock-frequency = <60000000>; interrupts = <3 4>; interrupt-parent = <&plic0>; };@@ -119,11 +119,89 @@ interrupt-parent = <&plic0>; }; + dma0: dma at f0c00000 { + compatible = "andestech,atcdmac300"; + reg = <0x0 0xf0c00000 0x0 0x1000>; + interrupts = <10 4 64 4 65 4 66 4 67 4 68 4 69 4 70 4 71 4>; + dma-channels = <8>; + interrupt-parent = <&plic0>; + }; + + lcd0: lcd at e0200000 { + compatible = "andestech,atflcdc100"; + reg = <0x0 0xe0200000 0x0 0x1000>; + interrupts = <20 4>; + interrupt-parent = <&plic0>; + }; + smc0: smc at e0400000 { compatible = "andestech,atfsmc020"; reg = <0x0 0xe0400000 0x0 0x1000>; }; + snd0: snd at f0d00000 { + compatible = "andestech,atfac97"; + reg = <0x0 0xf0d00000 0x0 0x1000>; + interrupts = <17 4>; + interrupt-parent = <&plic0>; + }; + + virtio_mmio at fe007000 { + interrupts = <0x17 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe007000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe006000 { + interrupts = <0x16 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe006000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe005000 { + interrupts = <0x15 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe005000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe004000 { + interrupts = <0x14 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe004000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe003000 { + interrupts = <0x13 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe003000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe002000 { + interrupts = <0x12 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe002000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe001000 { + interrupts = <0x11 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe001000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; + + virtio_mmio at fe000000 {Quoted 8 lines
arch/riscv/dts/ae350.dts line 204
Quoted 6 lines
arch/riscv/dts/ae350.dts +6
-0+ interrupts = <0x10 0x4>; + interrupt-parent = <0x2>; + reg = <0x0 0xfe000000 0x0 0x1000>; + compatible = "virtio,mmio"; + }; +Do these virtio devices exist on the real hardware?
Hi Bin
Quoted 8 lines
Quoted 4 lines
No.
These virtio nodes does not exist on the read board. It is required on Andes' QEMU ae350 board.So it is a special target, which matches some hardware components plus some "virtual" components like VirtIO?
Yes.
Quoted 2 lines
BTW: where is the Linux AE350 DTS file? I do not see it in the Linux tree.
The dts has not been pushed into Linux tree yet.
Rick
Quoted 2 lines
Regards,
Bin