net: Add MT7628 ethernet driver
Subsystems (2)
PATCH v6 1/1 net: Add MT7628 ethernet driver
This patch adds ethernet support for the MIPS based Mediatek MT76xx SoCs (e.g. MT7628 and MT7688), including a minimum setup of the integrated switch. This driver is loosly based on the driver version included in this MediaTek github repository:
https://github.com/MediaTek-Labs/linkit-smart-uboot.git
Tested on the MT7688 LinkIt smart-gateway and on the Gardena-smart-gateway.
---
v6:
- Simplified MAC address assignment
- Added free_pkt functions as suggested by Joe
v5:
- Rename driver and Kconfig and functions names again to avoid mix-up with the MT76xx ARM SoCs
v4:
- Rename driver and Kconfig to avoid mix-up with the MT76xx ARM SoCs
v3:
- Add Reviewed-by from Daniel
- Address review comments from Joe:
- Use more macros / defines instead of magic values, especially in the MDIO functions
- Use FIELD_xxx from include/linux/bitfield.h whereever possible
- Remove some unreferenced defines
- Remove some unnecessary casts
- Spelling fixes
- Add documentation in doc/device-tree-bindings/net/
v2:
- Use wait_for_bit_le32() in more places
- Use syscon / regmap to access the system-controller registers needed in this driver instead of finding and mapping this area
.../net/mediatek,mt7628-eth.txt | 17 + drivers/net/Kconfig | 7 + drivers/net/Makefile | 1 + drivers/net/mt7628-eth.c | 644 ++++++++++++++++++ 4 files changed, 669 insertions(+) create mode 100644 doc/device-tree-bindings/net/mediatek,mt7628-eth.txt create mode 100644 drivers/net/mt7628-eth.c
doc/device-tree-bindings/net/mediatek,mt7628-eth.txt new file +17 -0
@@ -0,0 +1,17 @@ +* MediaTek Frame Engine Ethernet controller + +Required properties: +- compatible: should be "mediatek,mt7628-eth" +- reg: address and length of the register set for the frame + engine ethernet controller and the internal switch. +- syscon: phandle to the system controller + +Example: + +eth at 10100000 { + compatible = "mediatek,mt7628-eth"; + reg = <0x10100000 0x10000 + 0x10110000 0x8000>; + + syscon = <&sysc>; +};
drivers/net/Kconfig +7 -0
@@ -227,6 +227,13 @@ config MACB_ZYNQ The Cadence MACB ethernet interface was used on Zynq platform. Say Y to enable support for the MACB/GEM in Zynq chip. +config MT7628_ETH + bool "MediaTek MT7628 Ethernet Interface" + depends on ARCH_MT7620 + help + The MediaTek MT7628 ethernet interface is used on MT7628 and + MT7688 based boards. + config PCH_GBE bool "Intel Platform Controller Hub EG20T GMAC driver" depends on DM_ETH && DM_PCI
drivers/net/Makefile +1 -0
@@ -37,6 +37,7 @@ obj-$(CONFIG_LPC32XX_ETH) += lpc32xx_eth.o obj-$(CONFIG_MACB) += macb.o obj-$(CONFIG_MCFFEC) += mcffec.o mcfmii.o obj-$(CONFIG_MPC8XX_FEC) += mpc8xx_fec.o +obj-$(CONFIG_MT7628_ETH) += mt7628-eth.o obj-$(CONFIG_MVGBE) += mvgbe.o obj-$(CONFIG_MVNETA) += mvneta.o obj-$(CONFIG_MVPP2) += mvpp2.o
drivers/net/mt7628-eth.c new file +644 -0
644 lines not on this page · raw message
Signature · 1 line
2.19.1
PATCH v6 1/1 net: Add MT7628 ethernet driver
Quoted 8 lines · Stefan Roese
This patch adds ethernet support for the MIPS based Mediatek MT76xx SoCs (e.g. MT7628 and MT7688), including a minimum setup of the integrated switch. This driver is loosly based on the driver version included in this MediaTek github repository:
Quoted 8 lines
Tested on the MT7688 LinkIt smart-gateway and on the Gardena-smart-gateway.
Signed-off-by Stefan Roese <[email protected]>Reviewed-by Daniel Schwierzeck <[email protected]>Cc Joe Hershberger <[email protected]>Cc Frank Wunderlich <[email protected]>Cc Weijie Gao <[email protected]>
Hi Stefan,
https://patchwork.ozlabs.org/patch/989567/ was applied to http://git.denx.de/?p=u-boot/u-boot-net.git
Thanks!
-Joe