pinctrl: rockchip: allow specifying the regmap location for pin-routes
Subsystems (3)
Heiko Stuebner
maintainerPATCH 1/2 pinctrl: rockchip: allow specifying the regmap location for pin-routes
From: Heiko Stuebner <[email protected]>
Right now we expect the pin-rounting settings to be in the same area as the iomux setting itself. And while that seems to be true for all newer Rockchip socs, back in the wild west days of old this wasn't true.
Nowadays pin settings in the GRF normally stay in the GRF and the same is true for pins configured from PMU registers. But old socs like the rk3188 really sprinkle pin settings somewhat randomly through both for its bank0.
Therefore add the option to specify a location for the route setting, so that we can map older socs correctly. We'll keep "same" as the default, so that we only need to specify a location in the corner-cases described above.
--- drivers/pinctrl/pinctrl-rockchip.c | 30 +++++++++++++++++++++++++----- 1 file changed, 25 insertions(+), 5 deletions(-)
drivers/pinctrl/pinctrl-rockchip.c +25 -5
@@ -307,6 +307,12 @@ struct rockchip_mux_recalced_data {u8 mask; }; +enum rockchip_mux_route_location { +ROCKCHIP_ROUTE_SAME =0 , +ROCKCHIP_ROUTE_PMU , +ROCKCHIP_ROUTE_GRF , +}; +/** * struct rockchip_mux_recalced_data: represent a pin iomux data. * @bank_num: bank number.
@@ -319,6 +325,7 @@ struct rockchip_mux_route_data {u8 bank_num;u8 pin;u8 func; +enum rockchip_mux_route_location route_location;u32 route_offset;u32 route_val; };
@@ -1091,7 +1098,7 @@ static struct rockchip_mux_route_data rk3399_mux_route_data[] = { };static bool rockchip_get_mux_route (struct rockchip_pin_bank *bank,int pin, -int mux,u32 *reg,u32 *value) +int mux,u32 *loc,u32 *reg,u32 *value) {struct rockchip_pinctrl *info = bank->drvdata;struct rockchip_pin_ctrl *ctrl = info->ctrl;
@@ -1108,6 +1115,7 @@ static bool rockchip_get_mux_route(struct rockchip_pin_bank *bank, int pin,if (i >= ctrl->niomux_routes)return false; + *loc = data->route_location; *reg = data->route_offset; *value = data->route_val;
@@ -1210,7 +1218,7 @@ static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)struct regmap *regmap;int reg, ret, mask, mux_type;u8 bit; -u32 data, rmask, route_reg, route_val; +u32 data, rmask, route_location, route_reg, route_val; ret =rockchip_verify_mux (bank, pin, mux);if (ret <0 )
@@ -1247,9 +1255,21 @@ static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)rockchip_get_recalced_mux (bank, pin, ®, &bit, &mask);if (bank->route_mask &BIT (pin)) { -if (rockchip_get_mux_route (bank, pin, mux, &route_reg, - &route_val)) { - ret =regmap_write (regmap, route_reg, route_val); +if (rockchip_get_mux_route (bank, pin, mux, &route_location, + &route_reg, &route_val)) { +struct regmap *route_regmap = regmap; + +/* handle special locations */ +switch (route_location) { +case ROCKCHIP_ROUTE_PMU : + route_regmap = info->regmap_pmu; +break ; +case ROCKCHIP_ROUTE_GRF : + route_regmap = info->regmap_base; +break ; + } + + ret =regmap_write (route_regmap, route_reg, route_val);if (ret)return ret; }
Signature · 1 line
2.18.0
Heiko Stuebner
maintainerPATCH 2/2 pinctrl: rockchip: add rk3188 routes to switch between nand and emmc
From: Heiko Stuebner <[email protected]>
The rk3188 has pins that are not handled through the regular iomuxing for handling either nand-flash or an emmc and are set through only one specifal setting. So utilize the routing function to simply do that setting depending on one of the core nand/emmc signals that are actually regular pins handled through pinctrl.
--- drivers/pinctrl/pinctrl-rockchip.c | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)
drivers/pinctrl/pinctrl-rockchip.c +22 -0
@@ -822,6 +822,26 @@ static struct rockchip_mux_route_data rk3128_mux_route_data[] = { }, }; +static struct rockchip_mux_route_data rk3188_mux_route_data[] = { + { +/* non-iomuxed emmc/flash pins on flash-dqs */ + .bank_num =0 , + .pin =24 , + .func =1 , + .route_location =ROCKCHIP_ROUTE_GRF , + .route_offset =0xa0 , + .route_val =BIT (16 +11 ), + }, { +/* non-iomuxed emmc/flash pins on emmc-clk */ + .bank_num =0 , + .pin =24 , + .func =2 , + .route_location =ROCKCHIP_ROUTE_GRF , + .route_offset =0xa0 , + .route_val =BIT (16 +11 ) |BIT (11 ), + }, +}; +static struct rockchip_mux_route_data rk3228_mux_route_data[] = { {/* pwm0-0 */
@@ -3626,6 +3646,8 @@ static struct rockchip_pin_ctrl rk3188_pin_ctrl = { .label = "RK3188-GPIO", .type = RK3188, .grf_mux_offset = 0x60, + .iomux_routes = rk3188_mux_route_data, + .niomux_routes = ARRAY_SIZE(rk3188_mux_route_data), .pull_calc_reg = rk3188_calc_pull_reg_and_bit, };
Signature · 1 line
2.18.0
Re: [PATCH 2/2] pinctrl: rockchip: add rk3188 routes to switch between nand and emmc
Quoted 9 lines · Heiko Stuebner
From: Heiko Stuebner <[email protected]>
The rk3188 has pins that are not handled through the regular iomuxing for handling either nand-flash or an emmc and are set through only one specifal setting. So utilize the routing function to simply do that setting depending on one of the core nand/emmc signals that are actually regular pins handled through pinctrl.
Signed-off-by Heiko Stuebner <[email protected]>
Patch applied.
Yours,
Linus Walleij
Hi Heiko,
? 2018/11/12 ??5:00, Heiko Stuebner ??:
Quoted 11 lines
From: Heiko Stuebner<[email protected]>
Right now we expect the pin-rounting settings to be in the same area as the iomux setting itself. And while that seems to be true for all newer Rockchip socs, back in the wild west days of old this wasn't true.
Nowadays pin settings in the GRF normally stay in the GRF and the same is true for pins configured from PMU registers. But old socs like the rk3188 really sprinkle pin settings somewhat randomly through both for its bank0.
Quoted 6 lines
Therefore add the option to specify a location for the route setting, so that we can map older socs correctly. We'll keep "same" as the default, so that we only need to specify a location in the corner-cases described above.
Signed-off-by Heiko Stuebner<[email protected]>
Very good, for the mixed case, really need to do the supplement.
Quoted 11 lines · Heiko Stuebner
From: Heiko Stuebner <[email protected]>
Right now we expect the pin-rounting settings to be in the same area as the iomux setting itself. And while that seems to be true for all newer Rockchip socs, back in the wild west days of old this wasn't true.
Nowadays pin settings in the GRF normally stay in the GRF and the same is true for pins configured from PMU registers. But old socs like the rk3188 really sprinkle pin settings somewhat randomly through both for its bank0.
Quoted 6 lines
Therefore add the option to specify a location for the route setting, so that we can map older socs correctly. We'll keep "same" as the default, so that we only need to specify a location in the corner-cases described above.
Signed-off-by Heiko Stuebner <[email protected]>
Patch applied with David's review tag.
Yours,
Linus Walleij