ARM: dts: qcom: Remove Arrow SD600 eval board
Subsystems (3)
PATCH 1/1 ARM: dts: qcom: Remove Arrow SD600 eval board
This patch removes support for the APQ8064 based Arrow SD600 eval board. This board was never sold publicly and had very limited distribution. As such, we are removing this board and no longer going to support it.
Signed-off-by Andy Gross <[email protected]>
--- arch/arm/boot/dts/Makefile | 1 - .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 53 --- .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 415 --------------------- 3 files changed, 469 deletions(-) delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
arch/arm/boot/dts/Makefile +0 -1
@@ -783,7 +783,6 @@ dtb-$(CONFIG_ARCH_OXNAS) += \ ox820-cloudengines-pogoplug-series-3.dtb dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8060-dragonboard.dtb \ - qcom-apq8064-arrow-sd-600eval.dtb \ qcom-apq8064-cm-qs600.dtb \ qcom-apq8064-ifc6410.dtb \ qcom-apq8064-sony-xperia-yuga.dtb \
arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi deleted +0 -53
53 lines not on this page · raw message
arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts deleted +0 -415
415 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH 1/1 ARM: dts: qcom: Remove Arrow SD600 eval board
Quoted 6 lines · Andy Gross
This patch removes support for the APQ8064 based Arrow SD600 eval board. This board was never sold publicly and had very limited distribution. As such, we are removing this board and no longer going to support it.
Signed-off-by Andy Gross <[email protected]>
Reviewed-by Bjorn Andersson <[email protected]>
Regards,
Bjorn
Quoted 503 lines
--- arch/arm/boot/dts/Makefile | 1 - .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 53 --- .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 415 --------------------- 3 files changed, 469 deletions(-) delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dtsarch/arm/boot/dts/Makefile +0
-1@@ -783,7 +783,6 @@ dtb-$(CONFIG_ARCH_OXNAS) += \ ox820-cloudengines-pogoplug-series-3.dtb dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8060-dragonboard.dtb \ - qcom-apq8064-arrow-sd-600eval.dtb \ qcom-apq8064-cm-qs600.dtb \ qcom-apq8064-ifc6410.dtb \ qcom-apq8064-sony-xperia-yuga.dtb \arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi deleted +0
-53@@ -1,53 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -&tlmm_pinmux { - card_detect: card-detect { - mux { - pins = "gpio26"; - function = "gpio"; - bias-disable; - }; - }; - - pcie_pins: pcie-pinmux { - mux { - pins = "gpio27"; - function = "gpio"; - }; - conf { - pins = "gpio27"; - drive-strength = <12>; - bias-disable; - }; - }; - - user_leds: user-leds { - mux { - pins = "gpio3", "gpio7", "gpio10", "gpio11"; - function = "gpio"; - }; - - conf { - pins = "gpio3", "gpio7", "gpio10", "gpio11"; - function = "gpio"; - output-low; - }; - }; - - magneto_pins: magneto-pins { - mux { - pins = "gpio31", "gpio48"; - function = "gpio"; - bias-disable; - }; - }; -}; - -&pm8921_mpps { - mpp_leds: mpp-leds { - pinconf { - pins = "mpp7", "mpp8"; - function = "digital"; - output-low; - }; - }; -};arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts deleted +0
-415@@ -1,415 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include "qcom-apq8064-v2.0.dtsi" -#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/mfd/qcom-rpm.h> - -/ { - model = "Arrow Electronics, APQ8064 SD_600eval"; - compatible = "arrow,sd_600eval", "qcom,apq8064"; - - aliases { - serial0 = &gsbi7_serial; - serial1 = &gsbi1_serial; - i2c0 = &gsbi2_i2c; - i2c1 = &gsbi3_i2c; - i2c2 = &gsbi4_i2c; - i2c3 = &gsbi7_i2c; - spi0 = &gsbi5_spi; - }; - - regulators { - compatible = "simple-bus"; - vph: regulator-fixed at 1 { - compatible = "regulator-fixed"; - regulator-min-microvolt = <4500000>; - regulator-max-microvolt = <4500000>; - regulator-name = "VPH"; - regulator-type = "voltage"; - regulator-boot-on; - }; - - /* on board fixed 3.3v supply */ - vcc3v3: vcc3v3 { - compatible = "regulator-fixed"; - regulator-name = "VCC3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - }; - - hdmi-out { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_con: endpoint { - remote-endpoint = <&hdmi_out>; - }; - }; - }; - - soc { - rpm at 108000 { - regulators { - vdd_s1-supply = <&vph>; - vdd_s2-supply = <&vph>; - vdd_s3-supply = <&vph>; - vdd_s4-supply = <&vph>; - vdd_s5-supply = <&vph>; - vdd_s6-supply = <&vph>; - vdd_s7-supply = <&vph>; - vdd_l1_l2_l12_l18-supply = <&pm8921_s4>; - vdd_l3_l15_l17-supply = <&vph>; - vdd_l4_l14-supply = <&vph>; - vdd_l5_l8_l16-supply = <&vph>; - vdd_l6_l7-supply = <&vph>; - vdd_l9_l11-supply = <&vph>; - vdd_l10_l22-supply = <&vph>; - vdd_l21_l23_l29-supply = <&vph>; - vdd_l24-supply = <&pm8921_s1>; - vdd_l25-supply = <&pm8921_s1>; - vdd_l26-supply = <&pm8921_s7>; - vdd_l27-supply = <&pm8921_s7>; - vdd_l28-supply = <&pm8921_s7>; - vin_lvs1_3_6-supply = <&pm8921_s4>; - vin_lvs2-supply = <&pm8921_s1>; - vin_lvs4_5_7-supply = <&pm8921_s4>; - - s1 { - regulator-always-on; - regulator-min-microvolt = <1225000>; - regulator-max-microvolt = <1225000>; - qcom,switch-mode-frequency = <3200000>; - bias-pull-down; - }; - - s2 { - regulator-min-microvolt = <1300000>; - regulator-max-microvolt = <1300000>; - qcom,switch-mode-frequency = <1600000>; - bias-pull-down; - regulator-always-on; - }; - - s3 { - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1400000>; - qcom,switch-mode-frequency = <4800000>; - }; - - s4 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - qcom,switch-mode-frequency = <1600000>; - qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>; - bias-pull-down; - regulator-always-on; - }; - - s7 { - regulator-min-microvolt = <1300000>; - regulator-max-microvolt = <1300000>; - qcom,switch-mode-frequency = <3200000>; - }; - - l3 { - regulator-min-microvolt = <3050000>; - regulator-max-microvolt = <3300000>; - bias-pull-down; - }; - - l4 { - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1800000>; - bias-pull-down; - }; - - l5 { - regulator-min-microvolt = <2750000>; - regulator-max-microvolt = <3000000>; - bias-pull-down; - regulator-boot-on; - regulator-always-on; - }; - - l6 { - regulator-min-microvolt = <2950000>; - regulator-max-microvolt = <2950000>; - bias-pull-down; - }; - - /** - * 1.8v required on LS expansion - * for mezzanine boards - */ - l15 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - l23 { - regulator-min-microvolt = <1700000>; - regulator-max-microvolt = <1900000>; - bias-pull-down; - }; - - lvs6 { - bias-pull-down; - }; - - lvs7 { - bias-pull-down; - }; - }; - }; - - gsbi at 12440000 { - status = "okay"; - qcom,mode = <GSBI_PROT_UART_W_FC>; - serial at 12450000 { - label = "LS-UART1"; - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&gsbi1_uart_4pins>; - }; - }; - - gsbi at 12480000 { - status = "okay"; - qcom,mode = <GSBI_PROT_I2C>; - i2c at 124a0000 { - /* On Low speed expansion and Sensors */ - label = "LS-I2C0"; - status = "okay"; - lis3mdl_mag at 1e { - compatible = "st,lis3mdl-magn"; - reg = <0x1e>; - vdd-supply = <&vcc3v3>; - vddio-supply = <&pm8921_s4>; - pinctrl-names = "default"; - pinctrl-0 = <&magneto_pins>; - interrupt-parent = <&tlmm_pinmux>; - - st,drdy-int-pin = <2>; - interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */ - <31 IRQ_TYPE_EDGE_RISING>; /* INT */ - }; - }; - }; - - gsbi at 16200000 { - status = "okay"; - qcom,mode = <GSBI_PROT_I2C>; - i2c at 16280000 { - /* On Low speed expansion */ - status = "okay"; - label = "LS-I2C1"; - clock-frequency = <200000>; - eeprom at 52 { - compatible = "atmel,24c128"; - reg = <0x52>; - pagesize = <64>; - }; - }; - }; - - gsbi at 16300000 { - status = "okay"; - qcom,mode = <GSBI_PROT_I2C>; - i2c at 16380000 { - /* On High speed expansion */ - label = "HS-CAM-I2C3"; - status = "okay"; - }; - }; - - gsbi at 1a200000 { - status = "okay"; - spi at 1a280000 { - /* On Low speed expansion */ - label = "LS-SPI0"; - status = "okay"; - }; - }; - - /* DEBUG UART */ - gsbi at 16600000 { - status = "okay"; - qcom,mode = <GSBI_PROT_I2C_UART>; - serial at 16640000 { - label = "LS-UART0"; - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&gsbi7_uart_2pins>; - }; - - i2c at 16680000 { - /* On High speed expansion */ - status = "okay"; - label = "HS-CAM-I2C2"; - }; - }; - - leds { - pinctrl-names = "default"; - pinctrl-0 = <&user_leds>, <&mpp_leds>; - - compatible = "gpio-leds"; - - user-led0 { - label = "user0-led"; - gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; - - user-led1 { - label = "user1-led"; - gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc0"; - default-state = "off"; - }; - - user-led2 { - label = "user2-led"; - gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc1"; - default-state = "off"; - }; - - user-led3 { - label = "user3-led"; - gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "none"; - default-state = "off"; - }; - - wifi-led { - label = "WiFi-led"; - gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - bt-led { - label = "BT-led"; - gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - }; - - pci at 1b500000 { - status = "okay"; - vdda-supply = <&pm8921_s3>; - vdda_phy-supply = <&pm8921_lvs6>; - vdda_refclk-supply = <&vcc3v3>; - pinctrl-0 = <&pcie_pins>; - pinctrl-names = "default"; - perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>; - }; - - phy at 1b400000 { - status = "okay"; - }; - - sata at 29000000 { - status = "okay"; - target-supply = <&pm8921_lvs7>; - }; - - /* OTG */ - usb at 12500000 { - status = "okay"; - dr_mode = "peripheral"; - ulpi { - phy { - v3p3-supply = <&pm8921_l3>; - v1p8-supply = <&pm8921_l4>; - }; - }; - }; - - usb at 12520000 { - status = "okay"; - dr_mode = "otg"; - ulpi { - phy { - v3p3-supply = <&pm8921_l3>; - v1p8-supply = <&pm8921_l23>; - }; - }; - }; - - usb at 12530000 { - status = "okay"; - dr_mode = "otg"; - ulpi { - phy { - v3p3-supply = <&pm8921_l3>; - v1p8-supply = <&pm8921_l23>; - }; - }; - }; - - amba { - /* eMMC */ - sdcc at 12400000 { - status = "okay"; - vmmc-supply = <&pm8921_l5>; - vqmmc-supply = <&pm8921_s4>; - }; - - /* External micro SD card */ - sdcc at 12180000 { - status = "okay"; - vmmc-supply = <&pm8921_l6>; - pinctrl-names = "default"; - pinctrl-0 = <&card_detect>; - cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - }; - - riva-pil at 3204000 { - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>; - }; - - hdmi-tx at 4a00000 { - status = "okay"; - core-vdda-supply = <&pm8921_hdmi_switch>; - hdmi-mux-supply = <&vcc3v3>; - - hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>; - - ports { - port at 1 { - endpoint { - remote-endpoint = <&hdmi_con>; - }; - }; - }; - }; - - hdmi-phy at 4a00400 { - status = "okay"; - core-vdda-supply = <&pm8921_hdmi_switch>; - }; - - mdp at 5100000 { - status = "okay"; - - ports { - port at 3 { - endpoint { - remote-endpoint = <&hdmi_in>; - }; - }; - }; - }; - }; -};Signature · 1 line
2.7.4
PATCH 1/1 ARM: dts: qcom: Remove Arrow SD600 eval board
In reply to Andy GrossQuoted 7 lines · Andy Gross
This patch removes support for the APQ8064 based Arrow SD600 eval board. This board was never sold publicly and had very limited distribution. As such, we are removing this board and no longer going to support it.
Signed-off-by Andy Gross <[email protected]>
Reviewed-by Nicolas Dechesne <[email protected]>
Quoted 503 lines
--- arch/arm/boot/dts/Makefile | 1 - .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 53 --- .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 415 --------------------- 3 files changed, 469 deletions(-) delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dtsarch/arm/boot/dts/Makefile +0
-1@@ -783,7 +783,6 @@ dtb-$(CONFIG_ARCH_OXNAS) += \ ox820-cloudengines-pogoplug-series-3.dtb dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8060-dragonboard.dtb \ - qcom-apq8064-arrow-sd-600eval.dtb \ qcom-apq8064-cm-qs600.dtb \ qcom-apq8064-ifc6410.dtb \ qcom-apq8064-sony-xperia-yuga.dtb \arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi deleted +0
-53@@ -1,53 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -&tlmm_pinmux { - card_detect: card-detect { - mux { - pins = "gpio26"; - function = "gpio"; - bias-disable; - }; - }; - - pcie_pins: pcie-pinmux { - mux { - pins = "gpio27"; - function = "gpio"; - }; - conf { - pins = "gpio27"; - drive-strength = <12>; - bias-disable; - }; - }; - - user_leds: user-leds { - mux { - pins = "gpio3", "gpio7", "gpio10", "gpio11"; - function = "gpio"; - }; - - conf { - pins = "gpio3", "gpio7", "gpio10", "gpio11"; - function = "gpio"; - output-low; - }; - }; - - magneto_pins: magneto-pins { - mux { - pins = "gpio31", "gpio48"; - function = "gpio"; - bias-disable; - }; - }; -}; - -&pm8921_mpps { - mpp_leds: mpp-leds { - pinconf { - pins = "mpp7", "mpp8"; - function = "digital"; - output-low; - }; - }; -};arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts deleted +0
-416@@ -1,415 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include "qcom-apq8064-v2.0.dtsi" -#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/mfd/qcom-rpm.h> - -/ { - model = "Arrow Electronics, APQ8064 SD_600eval"; - compatible = "arrow,sd_600eval", "qcom,apq8064"; - - aliases { - serial0 = &gsbi7_serial; - serial1 = &gsbi1_serial; - i2c0 = &gsbi2_i2c; - i2c1 = &gsbi3_i2c; - i2c2 = &gsbi4_i2c; - i2c3 = &gsbi7_i2c; - spi0 = &gsbi5_spi; - }; - - regulators { - compatible = "simple-bus"; - vph: regulator-fixed at 1 { - compatible = "regulator-fixed"; - regulator-min-microvolt = <4500000>; - regulator-max-microvolt = <4500000>; - regulator-name = "VPH"; - regulator-type = "voltage"; - regulator-boot-on; - }; - - /* on board fixed 3.3v supply */ - vcc3v3: vcc3v3 { - compatible = "regulator-fixed"; - regulator-name = "VCC3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - }; - - hdmi-out { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_con: endpoint { - remote-endpoint = <&hdmi_out>; - }; - }; - }; - - soc { - rpm at 108000 { - regulators { - vdd_s1-supply = <&vph>; - vdd_s2-supply = <&vph>; - vdd_s3-supply = <&vph>; - vdd_s4-supply = <&vph>; - vdd_s5-supply = <&vph>; - vdd_s6-supply = <&vph>; - vdd_s7-supply = <&vph>; - vdd_l1_l2_l12_l18-supply = <&pm8921_s4>; - vdd_l3_l15_l17-supply = <&vph>; - vdd_l4_l14-supply = <&vph>; - vdd_l5_l8_l16-supply = <&vph>; - vdd_l6_l7-supply = <&vph>; - vdd_l9_l11-supply = <&vph>; - vdd_l10_l22-supply = <&vph>; - vdd_l21_l23_l29-supply = <&vph>; - vdd_l24-supply = <&pm8921_s1>; - vdd_l25-supply = <&pm8921_s1>; - vdd_l26-supply = <&pm8921_s7>; - vdd_l27-supply = <&pm8921_s7>; - vdd_l28-supply = <&pm8921_s7>; - vin_lvs1_3_6-supply = <&pm8921_s4>; - vin_lvs2-supply = <&pm8921_s1>; - vin_lvs4_5_7-supply = <&pm8921_s4>; - - s1 { - regulator-always-on; - regulator-min-microvolt = <1225000>; - regulator-max-microvolt = <1225000>; - qcom,switch-mode-frequency = <3200000>; - bias-pull-down; - }; - - s2 { - regulator-min-microvolt = <1300000>; - regulator-max-microvolt = <1300000>; - qcom,switch-mode-frequency = <1600000>; - bias-pull-down; - regulator-always-on; - }; - - s3 { - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1400000>; - qcom,switch-mode-frequency = <4800000>; - }; - - s4 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - qcom,switch-mode-frequency = <1600000>; - qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>; - bias-pull-down; - regulator-always-on; - }; - - s7 { - regulator-min-microvolt = <1300000>; - regulator-max-microvolt = <1300000>; - qcom,switch-mode-frequency = <3200000>; - }; - - l3 { - regulator-min-microvolt = <3050000>; - regulator-max-microvolt = <3300000>; - bias-pull-down; - }; - - l4 { - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1800000>; - bias-pull-down; - }; - - l5 { - regulator-min-microvolt = <2750000>; - regulator-max-microvolt = <3000000>; - bias-pull-down; - regulator-boot-on; - regulator-always-on; - }; - - l6 { - regulator-min-microvolt = <2950000>; - regulator-max-microvolt = <2950000>; - bias-pull-down; - }; - - /** - * 1.8v required on LS expansion - * for mezzanine boards - */ - l15 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - l23 { - regulator-min-microvolt = <1700000>; - regulator-max-microvolt = <1900000>; - bias-pull-down; - }; - - lvs6 { - bias-pull-down; - }; - - lvs7 { - bias-pull-down; - }; - }; - }; - - gsbi at 12440000 { - status = "okay"; - qcom,mode = <GSBI_PROT_UART_W_FC>; - serial at 12450000 { - label = "LS-UART1"; - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&gsbi1_uart_4pins>; - }; - }; - - gsbi at 12480000 { - status = "okay"; - qcom,mode = <GSBI_PROT_I2C>; - i2c at 124a0000 { - /* On Low speed expansion and Sensors */ - label = "LS-I2C0"; - status = "okay"; - lis3mdl_mag at 1e { - compatible = "st,lis3mdl-magn"; - reg = <0x1e>; - vdd-supply = <&vcc3v3>; - vddio-supply = <&pm8921_s4>; - pinctrl-names = "default"; - pinctrl-0 = <&magneto_pins>; - interrupt-parent = <&tlmm_pinmux>; - - st,drdy-int-pin = <2>; - interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */ - <31 IRQ_TYPE_EDGE_RISING>; /* INT */ - }; - }; - }; - - gsbi at 16200000 { - status = "okay"; - qcom,mode = <GSBI_PROT_I2C>; - i2c at 16280000 { - /* On Low speed expansion */ - status = "okay"; - label = "LS-I2C1"; - clock-frequency = <200000>; - eeprom at 52 { - compatible = "atmel,24c128"; - reg = <0x52>; - pagesize = <64>; - }; - }; - }; - - gsbi at 16300000 { - status = "okay"; - qcom,mode = <GSBI_PROT_I2C>; - i2c at 16380000 { - /* On High speed expansion */ - label = "HS-CAM-I2C3"; - status = "okay"; - }; - }; - - gsbi at 1a200000 { - status = "okay"; - spi at 1a280000 { - /* On Low speed expansion */ - label = "LS-SPI0"; - status = "okay"; - }; - }; - - /* DEBUG UART */ - gsbi at 16600000 { - status = "okay"; - qcom,mode = <GSBI_PROT_I2C_UART>; - serial at 16640000 { - label = "LS-UART0"; - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&gsbi7_uart_2pins>; - }; - - i2c at 16680000 { - /* On High speed expansion */ - status = "okay"; - label = "HS-CAM-I2C2"; - }; - }; - - leds { - pinctrl-names = "default"; - pinctrl-0 = <&user_leds>, <&mpp_leds>; - - compatible = "gpio-leds"; - - user-led0 { - label = "user0-led"; - gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; - - user-led1 { - label = "user1-led"; - gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc0"; - default-state = "off"; - }; - - user-led2 { - label = "user2-led"; - gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc1"; - default-state = "off"; - }; - - user-led3 { - label = "user3-led"; - gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "none"; - default-state = "off"; - }; - - wifi-led { - label = "WiFi-led"; - gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - bt-led { - label = "BT-led"; - gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - }; - - pci at 1b500000 { - status = "okay"; - vdda-supply = <&pm8921_s3>; - vdda_phy-supply = <&pm8921_lvs6>; - vdda_refclk-supply = <&vcc3v3>; - pinctrl-0 = <&pcie_pins>; - pinctrl-names = "default"; - perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>; - }; - - phy at 1b400000 { - status = "okay"; - }; - - sata at 29000000 { - status = "okay"; - target-supply = <&pm8921_lvs7>; - }; - - /* OTG */ - usb at 12500000 { - status = "okay"; - dr_mode = "peripheral"; - ulpi { - phy { - v3p3-supply = <&pm8921_l3>; - v1p8-supply = <&pm8921_l4>; - }; - }; - }; - - usb at 12520000 { - status = "okay"; - dr_mode = "otg"; - ulpi { - phy { - v3p3-supply = <&pm8921_l3>; - v1p8-supply = <&pm8921_l23>; - }; - }; - }; - - usb at 12530000 { - status = "okay"; - dr_mode = "otg"; - ulpi { - phy { - v3p3-supply = <&pm8921_l3>; - v1p8-supply = <&pm8921_l23>; - }; - }; - }; - - amba { - /* eMMC */ - sdcc at 12400000 { - status = "okay"; - vmmc-supply = <&pm8921_l5>; - vqmmc-supply = <&pm8921_s4>; - }; - - /* External micro SD card */ - sdcc at 12180000 { - status = "okay"; - vmmc-supply = <&pm8921_l6>; - pinctrl-names = "default"; - pinctrl-0 = <&card_detect>; - cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - }; - - riva-pil at 3204000 { - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>; - }; - - hdmi-tx at 4a00000 { - status = "okay"; - core-vdda-supply = <&pm8921_hdmi_switch>; - hdmi-mux-supply = <&vcc3v3>; - - hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>; - - ports { - port at 1 { - endpoint { - remote-endpoint = <&hdmi_con>; - }; - }; - }; - }; - - hdmi-phy at 4a00400 { - status = "okay"; - core-vdda-supply = <&pm8921_hdmi_switch>; - }; - - mdp at 5100000 { - status = "okay"; - - ports { - port at 3 { - endpoint { - remote-endpoint = <&hdmi_in>; - }; - }; - }; - }; - }; -}; --2.7.4
PATCH 1/1 ARM: dts: qcom: Remove Arrow SD600 eval board
In reply to Andy GrossQuoted 7 lines · Andy Gross
This patch removes support for the APQ8064 based Arrow SD600 eval board. This board was never sold publicly and had very limited distribution. As such, we are removing this board and no longer going to support it.
Signed-off-by Andy Gross <[email protected]>
It's currently throwing DTS warnings as well, so if nobody's interested in keeping it around, this seems OK with me.
Acked-by Olof Johansson <[email protected]>
-Olof