ARM: dts: sun8i: Add board dts file for t3-cqa3t-bv3.
Subsystems (6)
PATCH 1/2 ARM: dts: sun8i: Add board dts file for t3-cqa3t-bv3.
The T3/R40/V40 using the same sdk and config file in allwinner sdk, it seem they are the same SOC just with different name, so compatible with R40.
The t3-cqa3t-bv3 based on Allwinner T3 SoC, it has various connectors, leds, buttons, and sell on:
https://item.taobao.com/item.htm?spm=2013.1.w4023-4203040713.25.62704cce7UCgLS&id=557154455330
It features:
- X-Powers AXP221s PMIC connected to i2c0
- 1/2 GB DDR3 DRAM
- 8 GB eMMC
- 2x USB 2.0 hosts
- 1x USB 2.0 OTG
- 2 LVDS connectors
- 24 bit RGB LCD connector
- HDMI output
- DVP camera interface (support 500w cmos camera)
- GPIO connectors
- 5 TTL uarts and 2 RS232 uarts
- 1 RS485 connector
- support i2c capacitive tp and usb infrared tp
- boot control, reset and user buttons
- 3.5mm headphone and 3.5mm mic jack
- 100M RJ45
- micro SD card slot
- DC power jack
- RCT power slot
- 1 CVBS TVIN
- 1 CVBS TVOUT
- 2 customer leds
- 1 buzzer
- 1 minipcie
- I2C output
- SPI output
- PCM output
- wifi and bt connector reserved.
Board info can find here:
https://github.com/Axl-zhang/Allwinner-V40-T3-R40-manual
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun8i-t3-cqa3t-bv3.dts | 226 +++++++++++++++++++++++++++++++ 2 files changed, 227 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-t3-cqa3t-bv3.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -1053,6 +1053,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-r16-nintendo-super-nes-classic.dtb \ sun8i-r16-parrot.dtb \ sun8i-r40-bananapi-m2-ultra.dtb \ + sun8i-t3-cqa3t-bv3.dtb \ sun8i-v3s-licheepi-zero.dtb \ sun8i-v3s-licheepi-zero-dock.dtb \ sun8i-v40-bananapi-m2-berry.dtb
arch/arm/boot/dts/sun8i-t3-cqa3t-bv3.dts new file +226 -0
226 lines not on this page · raw message
Signature · 1 line
2.7.4
Maxime Ripard
AppliedQuoted 38 lines · Hao Zhang
The T3/R40/V40 using the same sdk and config file in allwinner sdk, it seem they are the same SOC just with different name, so compatible with R40.
The t3-cqa3t-bv3 based on Allwinner T3 SoC, it has various connectors, leds, buttons, and sell on:
https://item.taobao.com/item.htm?spm=2013.1.w4023-4203040713.25.62704cce7UCgLS&id=557154455330It features:
- X-Powers AXP221s PMIC connected to i2c0
- 1/2 GB DDR3 DRAM
- 8 GB eMMC
- 2x USB 2.0 hosts
- 1x USB 2.0 OTG
- 2 LVDS connectors
- 24 bit RGB LCD connector
- HDMI output
- DVP camera interface (support 500w cmos camera)
- GPIO connectors
- 5 TTL uarts and 2 RS232 uarts
- 1 RS485 connector
- support i2c capacitive tp and usb infrared tp
- boot control, reset and user buttons
- 3.5mm headphone and 3.5mm mic jack
- 100M RJ45
- micro SD card slot
- DC power jack
- RCT power slot
- 1 CVBS TVIN
- 1 CVBS TVOUT
- 2 customer leds
- 1 buzzer
- 1 minipcie
- I2C output
- SPI output
- PCM output
- wifi and bt connector reserved.
Quoted 4 lines
Board info can find here:
https://github.com/Axl-zhang/Allwinner-V40-T3-R40-manualSigned-off-by Hao Zhang <[email protected]>
Applied both patches, thanks!
Maxime
Signature · 10 lines
Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 228 bytes Desc: not available URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20181122/cb08f546/attachment.sig>