spi: Remove unused spi_init
Subsystems (7)
PATCH v2 1/6 spi: Remove unused spi_init
Remove spi_init definition which never used on
respective code since from many years.
Signed-off-by Jagan Teki <[email protected]>
--- drivers/net/e1000_spi.c | 3 --- drivers/spi/atmel_spi.c | 5 ----- drivers/spi/davinci_spi.c | 5 ----- drivers/spi/fsl_dspi.c | 5 ----- drivers/spi/fsl_espi.c | 5 ----- drivers/spi/lpc32xx_ssp.c | 9 --------- drivers/spi/mxc_spi.c | 4 ---- drivers/spi/mxs_spi.c | 4 ---- drivers/spi/omap3_spi.c | 5 ----- drivers/spi/sh_qspi.c | 5 ----- drivers/spi/sh_spi.c | 4 ---- drivers/spi/soft_spi_legacy.c | 7 ------- include/spi.h | 7 ------- 13 files changed, 68 deletions(-)
drivers/net/e1000_spi.c +0 -3
@@ -77,9 +77,6 @@ static inline struct e1000_hw *e1000_hw_from_spi(struct spi_slave *spi) return container_of(spi, struct e1000_hw, spi); } -/* Not sure why all of these are necessary */ -void spi_init (void ) {/* Nothing to do */ } -struct spi_slave *spi_setup_slave (unsigned int bus,unsigned int cs,unsigned int max_hz,unsigned int mode) {
drivers/spi/atmel_spi.c +0 -5
@@ -34,11 +34,6 @@ static int spi_has_wdrbt(struct atmel_spi_slave *slave)return (ATMEL_SPI_VERSION_REV (ver) >=0x210 ); } -void spi_init () -{ - -} -struct spi_slave *spi_setup_slave (unsigned int bus,unsigned int cs,unsigned int max_hz,unsigned int mode) {
drivers/spi/davinci_spi.c +0 -5
@@ -388,11 +388,6 @@ void spi_cs_deactivate(struct spi_slave *slave)/* do nothing */ } -void spi_init (void ) -{ -/* do nothing */ -} -struct spi_slave *spi_setup_slave (unsigned int bus,unsigned int cs,unsigned int max_hz,unsigned int mode) {
drivers/spi/fsl_dspi.c +0 -5
@@ -390,11 +390,6 @@ static int fsl_dspi_cfg_speed(struct fsl_dspi_priv *priv, uint speed)return 0 ; }#ifndef CONFIG_DM_SPI -void spi_init (void ) -{ -/* Nothing to do */ -} -int spi_cs_is_valid (unsigned int bus,unsigned int cs) {if (((cs >=0 ) && (cs <8 )) && ((bus >=0 ) && (bus <8 )))
drivers/spi/fsl_espi.c +0 -5
@@ -118,11 +118,6 @@ void spi_free_slave(struct spi_slave *slave)free (fsl); } -void spi_init (void ) -{ - -} -int spi_claim_bus (struct spi_slave *slave) {struct fsl_spi_slave *fsl =to_fsl_spi_slave (slave);
drivers/spi/lpc32xx_ssp.c +0 -9
@@ -47,15 +47,6 @@ static inline struct lpc32xx_spi_slave *to_lpc32xx_spi_slave( return container_of(slave, struct lpc32xx_spi_slave, slave); } -/* spi_init is called during boot when CONFIG_CMD_SPI is defined */ -void spi_init (void ) -{ -/* -* nothing to do: clocking was enabled in lpc32xx_ssp_enable() -* and configuration will be done in spi_setup_slave() -*/ -} -/* the following is called in sequence by do_spi_xfer() */ struct spi_slave *spi_setup_slave (uint bus,uint cs,uint max_hz,uint mode)
drivers/spi/mxc_spi.c +0 -4
@@ -400,10 +400,6 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,return mxc_spi_xfer_internal (mxcs, bitlen, dout, din, flags); } -void spi_init (void ) -{ -} -/* * Some SPI devices require active chip-select over multiple * transactions, we achieve this using a GPIO. Still, the SPI
drivers/spi/mxs_spi.c +0 -4
@@ -39,10 +39,6 @@ static inline struct mxs_spi_slave *to_mxs_slave(struct spi_slave *slave) return container_of(slave, struct mxs_spi_slave, slave); } -void spi_init (void ) -{ -} -int spi_cs_is_valid (unsigned int bus,unsigned int cs) {/* MXS SPI: 4 ports and 3 chip selects maximum */
drivers/spi/omap3_spi.c +0 -5
@@ -461,11 +461,6 @@ static inline struct omap3_spi_priv *to_omap3_spi(struct spi_slave *slave) return container_of(slave, struct omap3_spi_priv, slave); } -void spi_init (void ) -{ -/* do nothing */ -} -void spi_free_slave (struct spi_slave *slave) {struct omap3_spi_priv *priv =to_omap3_spi (slave);
drivers/spi/sh_qspi.c +0 -5
@@ -247,11 +247,6 @@ void spi_cs_deactivate(struct spi_slave *slave)sh_qspi_cs_deactivate (ss); } -void spi_init (void ) -{ -/* nothing to do */ -} -struct spi_slave *spi_setup_slave (unsigned int bus,unsigned int cs,unsigned int max_hz,unsigned int mode) {
drivers/spi/sh_spi.c +0 -4
@@ -66,10 +66,6 @@ static int write_fifo_empty_wait(struct sh_spi *ss)return 0 ; } -void spi_init (void ) -{ -} -static void sh_spi_set_cs (struct sh_spi *ss,unsigned int cs) {unsigned long val =0 ;
drivers/spi/soft_spi_legacy.c +0 -7
@@ -36,13 +36,6 @@ static inline struct soft_spi_slave *to_soft_spi(struct spi_slave *slave)/* Public Functions */ /*=====================================================================*/ -/*----------------------------------------------------------------------- -* Initialization -*/ -void spi_init (void ) -{ -} -struct spi_slave *spi_setup_slave (unsigned int bus,unsigned int cs,unsigned int max_hz,unsigned int mode) {
include/spi.h +0 -7
@@ -117,13 +117,6 @@ struct spi_slave {#define SPI_XFER_MMAP_END BIT(3)/* Memory Mapped End */ }; -/** -* Initialization, must be called once on start up. -* -* TODO: I don't think we really need this. -*/ -void spi_init (void ); -/** * spi_do_alloc_slave - Allocate a new SPI slave (internal) *
Signature · 1 line
2.18.0.321.gffc6fa0e3
PATCH v2 1/6 spi: Remove unused spi_init
Quoted 6 lines · Jagan Teki
Remove
spi_initdefinition which never used on
respective code since from many years.Signed-off-by Jagan Teki <[email protected]>---
All patches,
Applied to u-boot-spi/maste
PATCH v2 2/6 spi: Remove used spi_init
In reply to Jagan Tekispi_init used in some areas in tree, but the respective drivers will remove in future patches.
So remove the same instances.
Signed-off-by Jagan Teki <[email protected]>
--- common/board_f.c | 2 -- doc/driver-model/spi-howto.txt | 5 ----- examples/standalone/atmel_df_pow2.c | 2 -- include/_exports.h | 2 -- 4 files changed, 11 deletions(-)
common/board_f.c +0 -2
@@ -23,7 +23,6 @@#include <os.h> #include <post.h> #include <relocate.h> -#include <spi.h> #include <status_led.h> #include <sysreset.h> #include <timer.h>
@@ -262,7 +261,6 @@ __weak int init_func_vid(void)static int init_func_spi (void ) {puts ("SPI: " ); -spi_init ();puts ("ready\n" );return 0 ; }
doc/driver-model/spi-howto.txt +0 -5
@@ -163,11 +163,6 @@ At this point you should be able to build U-Boot for your board with the empty SPI driver. You still have empty methods in your driver, but we will write these one by one. -If you have spi_init() functions or the like that are called from your -board then the build will fail. Remove these calls and make a note of the -init that needs to be done. - - 7. Set up your platform data structure This will hold the information your driver to operate, like its hardware
examples/standalone/atmel_df_pow2.c +0 -2
@@ -126,8 +126,6 @@ int atmel_df_pow2(int argc, char * const argv[])return 1 ; } -spi_init (); -while (1 ) {struct spi_slave *slave;char *line, *p;
include/_exports.h +0 -2
@@ -50,11 +50,9 @@#endif #if !defined(CONFIG_CMD_SPI ) || defined(CONFIG_DM_SPI ) - EXPORT_FUNC(dummy, void, spi_init, void) EXPORT_FUNC(dummy, void, spi_setup_slave, void) EXPORT_FUNC(dummy, void, spi_free_slave, void)#else - EXPORT_FUNC(spi_init, void, spi_init, void) EXPORT_FUNC(spi_setup_slave, struct spi_slave *, spi_setup_slave, unsigned int, unsigned int, unsigned int, unsigned int) EXPORT_FUNC(spi_free_slave, void, spi_free_slave, struct spi_slave *)
Signature · 1 line
2.18.0.321.gffc6fa0e3
PATCH v2 3/6 spi: mpc8xx: Migrate to DM_SPI
In reply to Jagan TekiFrom: Christophe Leroy <[email protected]>
Drop non-dm code and migrate into DM_SPI.
Signed-off-by Christophe Leroy <[email protected]>
[jagan: Move config menu in DM_SPI area]
Signed-off-by Jagan Teki <[email protected]>
--- drivers/spi/Kconfig | 12 +-- drivers/spi/mpc8xx_spi.c | 179 +++++++-------------------------------- 2 files changed, 36 insertions(+), 155 deletions(-)
drivers/spi/Kconfig +6 -6
@@ -124,6 +124,12 @@ config MESON_SPIFC This driver can be used to access the SPI NOR flash chips on Amlogic Meson SoCs. +config MPC8XX_SPI + bool "MPC8XX SPI Driver" + depends on MPC8xx + help + Enable support for SPI on MPC8XX + config MT7621_SPI bool "MediaTek MT7621 SPI driver" depends on ARCH_MT7620
@@ -343,12 +349,6 @@ config LPC32XX_SSP help Enable support for SPI on LPC32xx -config MPC8XX_SPI - bool "MPC8XX SPI Driver" - depends on MPC8xx - help - Enable support for SPI on MPC8XX - config MPC8XXX_SPI bool "MPC8XXX SPI Driver" help
drivers/spi/mpc8xx_spi.c +30 -149
224 lines not on this page · raw message
Signature · 1 line
2.18.0.321.gffc6fa0e3
PATCH v2 4/6 spi: Remove unused mpc8xx code
In reply to Jagan Teki- spi_init_f
- spi_init_r
- spi_read
- spi_write
these spi calls are exclusively for mpc8xx, but the relevant driver is not available so remove it.
Signed-off-by Jagan Teki <[email protected]>
--- cmd/eeprom.c | 15 +-------------- common/board_r.c | 7 ------- include/common.h | 7 ------- 3 files changed, 1 insertion(+), 28 deletions(-)
cmd/eeprom.c +1 -14
@@ -66,11 +66,6 @@ __weak int eeprom_write_enable(unsigned dev_addr, int state)void eeprom_init (int bus) { -/* SPI EEPROM */ -#if defined(CONFIG_MPC8XX_SPI ) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C ) -spi_init_f (); -#endif -/* I2C EEPROM */ #if defined(CONFIG_SYS_I2C )if (bus >=0 )
@@ -129,14 +124,6 @@ static int eeprom_rw_block(unsigned offset, uchar *addr, unsigned alen, {int ret =0 ; -/* SPI */ -#if defined(CONFIG_MPC8XX_SPI ) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C ) -if (read) -spi_read (addr, alen, buffer, len); -else -spi_write (addr, alen, buffer, len); -#else /* I2C */ -#if defined(CONFIG_SYS_I2C_EEPROM_BUS )i2c_set_bus_num (CONFIG_SYS_I2C_EEPROM_BUS );#endif
@@ -148,7 +135,7 @@ static int eeprom_rw_block(unsigned offset, uchar *addr, unsigned alen,if (ret) ret =1 ; -#endif +return ret; }
common/board_r.c +0 -7
@@ -382,13 +382,6 @@ static int initr_flash(void)#if defined(CONFIG_PPC ) && !defined(CONFIG_DM_SPI )static int initr_spi (void ) { -/* MPC8xx does this here */ -#ifdef CONFIG_MPC8XX_SPI -#if !defined(CONFIG_ENV_IS_IN_EEPROM ) -spi_init_f (); -#endif -spi_init_r (); -#endif return 0 ; }#endif
include/common.h +0 -7
@@ -276,13 +276,6 @@ int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned c# define CONFIG_SYS_DEF_EEPROM_ADDR CONFIG_SYS_I2C_EEPROM_ADDR#endif -#if defined(CONFIG_MPC8XX_SPI ) -extern void spi_init_f (void ); -extern void spi_init_r (void ); -extern ssize_t spi_read (uchar *,int ,uchar *,int ); -extern ssize_t spi_write (uchar *,int ,uchar *,int ); -#endif -/* $(BOARD)/$(BOARD).c */ int board_early_init_f (void );int board_fix_fdt (void *rw_fdt_blob);/* manipulate the U-Boot fdt before its relocation */
Signature · 1 line
2.18.0.321.gffc6fa0e3
PATCH v2 5/6 spi: Zap CONFIG_HARD_SPI
In reply to Jagan TekiIn legacy CONFIG_HARD_SPI initalizing spi_init code, which was removed during dm conversion cleanup.
So remove the dead instances of CONFIG_HARD_SPI, and related code.
Signed-off-by Jagan Teki <[email protected]>
--- README | 8 -------- arch/powerpc/include/asm/config.h | 7 ------- board/freescale/mpc8349emds/mpc8349emds.c | 2 +- board/ids/ids8313/ids8313.c | 2 +- common/board_f.c | 12 ------------ include/configs/M52277EVB.h | 1 - include/configs/M54418TWR.h | 1 - include/configs/M54451EVB.h | 1 - include/configs/M54455EVB.h | 1 - include/configs/MPC8536DS.h | 5 ----- include/configs/P1022DS.h | 6 ------ include/configs/UCP1020.h | 5 ----- include/configs/controlcenterd.h | 4 ---- include/configs/dreamplug.h | 1 - include/configs/ds109.h | 1 - include/configs/ids8313.h | 10 ---------- include/configs/mx31pdk.h | 1 - include/configs/mxs.h | 1 - include/configs/p1_p2_rdb_pc.h | 5 ----- include/configs/p1_twr.h | 5 ----- include/configs/stmark2.h | 1 - include/configs/ts4800.h | 5 ----- scripts/config_whitelist.txt | 1 - 23 files changed, 2 insertions(+), 84 deletions(-)
README +0 -8
@@ -1932,14 +1932,6 @@ The following options need to be configured: SPI configuration items (port pins to use, etc). For an example, see include/configs/sacsng.h. - CONFIG_HARD_SPI - - Enables a hardware SPI driver for general-purpose reads - and writes. As with CONFIG_SOFT_SPI, the board configuration - must define a list of chip-select function pointers. - Currently supported on some MPC8xxx processors. For an - example, see include/configs/mpc8349emds.h. - CONFIG_SYS_SPI_MXC_WAIT Timeout for waiting until spi transfer completed. default: (CONFIG_SYS_HZ/100) /* 10 ms */
arch/powerpc/include/asm/config.h +0 -7
@@ -18,13 +18,6 @@#define HWCONFIG_BUFFER_SIZE 256#endif -/* CONFIG_HARD_SPI triggers SPI bus initialization in PowerPC */ -#if defined(CONFIG_MPC8XXX_SPI ) || defined(CONFIG_FSL_ESPI ) -# ifndef CONFIG_HARD_SPI -# define CONFIG_HARD_SPI -# endif -#endif -#define CONFIG_LMB #define CONFIG_SYS_BOOT_RAMDISK_HIGH
board/freescale/mpc8349emds/mpc8349emds.c +1 -1
@@ -273,7 +273,7 @@ void spi_cs_deactivate(struct spi_slave *slave) iopd->dat |= SPI_CS_MASK; } -#endif /* CONFIG_HARD_SPI */ +#endif #if defined(CONFIG_OF_BOARD_SETUP )int ft_board_setup (void *blob,bd_t *bd)
board/ids/ids8313/ids8313.c +1 -1
@@ -208,4 +208,4 @@ void spi_cs_deactivate(struct spi_slave *slave)/* deactivate the spi_cs */ setbits_be32(&iopd->dat, IDSCPLD_SPI_CS_MASK); } -#endif /* CONFIG_HARD_SPI */ +#endif
common/board_f.c +0 -12
@@ -257,15 +257,6 @@ __weak int init_func_vid(void) }#endif -#if defined(CONFIG_HARD_SPI ) -static int init_func_spi (void ) -{ -puts ("SPI: " ); -puts ("ready\n" ); -return 0 ; -} -#endif -static int setup_mon_len (void ) {#if defined(__ARM__) || defined(__MICROBLAZE__)
@@ -863,9 +854,6 @@ static const init_fnc_t init_sequence_f[] = {#endif #if defined(CONFIG_VID ) && !defined(CONFIG_SPL ) init_func_vid, -#endif -#if defined(CONFIG_HARD_SPI ) - init_func_spi, #endif announce_dram_init, dram_init, /* configure available RAM banks */
include/configs/M52277EVB.h +0 -1
@@ -102,7 +102,6 @@/* DSPI and Serial Flash */ #define CONFIG_CF_DSPI -#define CONFIG_HARD_SPI #define CONFIG_SYS_SBFHDR_SIZE 0x7#ifdef CONFIG_CMD_SPI # define CONFIG_SYS_DSPI_CS2
include/configs/M54418TWR.h +0 -1
@@ -151,7 +151,6 @@/* DSPI and Serial Flash */ #define CONFIG_CF_DSPI #define CONFIG_SERIAL_FLASH -#define CONFIG_HARD_SPI #define CONFIG_SYS_SBFHDR_SIZE 0x7#ifdef CONFIG_CMD_SPI
include/configs/M54451EVB.h +0 -1
@@ -116,7 +116,6 @@/* DSPI and Serial Flash */ #define CONFIG_CF_DSPI #define CONFIG_SERIAL_FLASH -#define CONFIG_HARD_SPI #define CONFIG_SYS_SBFHDR_SIZE 0x7#ifdef CONFIG_CMD_SPI
include/configs/M54455EVB.h +0 -1
@@ -142,7 +142,6 @@/* DSPI and Serial Flash */ #define CONFIG_CF_DSPI -#define CONFIG_HARD_SPI #define CONFIG_SYS_SBFHDR_SIZE 0x13#ifdef CONFIG_CMD_SPI
include/configs/MPC8536DS.h +0 -5
@@ -370,11 +370,6 @@#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_BUS_NUM 1 -/* -* eSPI - Enhanced SPI -*/ -#define CONFIG_HARD_SPI -#if defined(CONFIG_SPI_FLASH )#define CONFIG_SF_DEFAULT_SPEED 10000000#define CONFIG_SF_DEFAULT_MODE 0
include/configs/P1022DS.h +0 -6
@@ -386,12 +386,6 @@#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_BUS_NUM 1 -/* -* eSPI - Enhanced SPI -*/ - -#define CONFIG_HARD_SPI -#define CONFIG_SF_DEFAULT_SPEED 10000000#define CONFIG_SF_DEFAULT_MODE 0
include/configs/UCP1020.h +0 -5
@@ -287,11 +287,6 @@#define CONFIG_SYS_I2C_NCT72_ADDR 0x4C#define CONFIG_SYS_I2C_IDT6V49205B 0x69 -/* -* eSPI - Enhanced SPI -*/ -#define CONFIG_HARD_SPI -#define CONFIG_SF_DEFAULT_SPEED 10000000#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
include/configs/controlcenterd.h +0 -4
@@ -182,10 +182,6 @@#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2#ifndef CONFIG_TRAILBLAZER -/* -* eSPI - Enhanced SPI -*/ -#define CONFIG_HARD_SPI #define CONFIG_SF_DEFAULT_SPEED 10000000#define CONFIG_SF_DEFAULT_MODE 0
include/configs/dreamplug.h +0 -1
@@ -35,7 +35,6 @@#endif #ifdef CONFIG_CMD_SF -#define CONFIG_HARD_SPI 1#define CONFIG_ENV_SPI_BUS 0#define CONFIG_ENV_SPI_CS 0#define CONFIG_ENV_SPI_MAX_HZ 50000000/* 50 MHz */
include/configs/ds109.h +0 -1
@@ -38,7 +38,6 @@#endif #ifdef CONFIG_CMD_SF -#define CONFIG_HARD_SPI 1#define CONFIG_ENV_SPI_BUS 0#define CONFIG_ENV_SPI_CS 0#define CONFIG_ENV_SPI_MAX_HZ 50000000/* 50 MHz */
include/configs/ids8313.h +0 -10
@@ -159,7 +159,6 @@*/ #define CONFIG_TSEC1 #define CONFIG_TSEC2 -#define CONFIG_HARD_SPI /* * NOR FLASH setup
@@ -273,15 +272,6 @@#define CONFIG_RTC_PCF8563 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 -/* -* SPI setup -*/ -#ifdef CONFIG_HARD_SPI -#define CONFIG_SYS_GPIO1_PRELIM -#define CONFIG_SYS_GPIO1_DIR 0x00000001 -#define CONFIG_SYS_GPIO1_DAT 0x00000001 -#endif -/* * Ethernet setup */
include/configs/mx31pdk.h +0 -1
@@ -43,7 +43,6 @@#define CONFIG_MXC_UART #define CONFIG_MXC_UART_BASE UART1_BASE -#define CONFIG_HARD_SPI #define CONFIG_DEFAULT_SPI_BUS 1#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
include/configs/mxs.h +0 -1
@@ -143,7 +143,6 @@/* SPI */ #ifdef CONFIG_CMD_SPI -#define CONFIG_HARD_SPI #define CONFIG_SPI_HALF_DUPLEX #endif
include/configs/p1_p2_rdb_pc.h +0 -5
@@ -576,11 +576,6 @@#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 -/* -* eSPI - Enhanced SPI -*/ -#define CONFIG_HARD_SPI -#if defined(CONFIG_SPI_FLASH )#define CONFIG_SF_DEFAULT_SPEED 10000000#define CONFIG_SF_DEFAULT_MODE 0
include/configs/p1_twr.h +0 -5
@@ -214,11 +214,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 -/* -* eSPI - Enhanced SPI -*/ -#define CONFIG_HARD_SPI -#if defined(CONFIG_PCI )/* * General PCI
include/configs/stmark2.h +0 -1
@@ -66,7 +66,6 @@#define CONFIG_CF_DSPI #define CONFIG_SF_DEFAULT_SPEED 50000000#define CONFIG_SERIAL_FLASH -#define CONFIG_HARD_SPI #define CONFIG_ENV_SPI_BUS 0#define CONFIG_ENV_SPI_CS 1
include/configs/ts4800.h +0 -5
@@ -42,11 +42,6 @@#define CONFIG_MXC_UART #define CONFIG_MXC_UART_BASE UART1_BASE -/* -* SPI Configs -* */ -#define CONFIG_HARD_SPI /* puts SPI: ready */ -/* * MMC Configs * */
scripts/config_whitelist.txt +0 -1
@@ -750,7 +750,6 @@ CONFIG_G_DNL_UMS_PRODUCT_NUM CONFIG_G_DNL_UMS_VENDOR_NUM CONFIG_H264_FREQ CONFIG_H8300 -CONFIG_HARD_SPI CONFIG_HAS_ETH0 CONFIG_HAS_ETH1 CONFIG_HAS_ETH2
Signature · 1 line
2.18.0.321.gffc6fa0e3
PATCH v2 6/6 board_r: Remove initr_spi
In reply to Jagan TekiDrop unused initr_spi, which just return 0, no usage.
Signed-off-by Jagan Teki <[email protected]>
--- common/board_r.c | 11 ----------- 1 file changed, 11 deletions(-)
common/board_r.c +0 -11
@@ -36,7 +36,6 @@#include <onenand_uboot.h> #include <scsi.h> #include <serial.h> -#include <spi.h> #include <stdio_dev.h> #include <timer.h> #include <trace.h>
@@ -379,13 +378,6 @@ static int initr_flash(void) }#endif -#if defined(CONFIG_PPC ) && !defined(CONFIG_DM_SPI ) -static int initr_spi (void ) -{ -return 0 ; -} -#endif -#ifdef CONFIG_CMD_NAND /* go init the NAND */ static int initr_nand (void )
@@ -736,9 +728,6 @@ static init_fnc_t init_sequence_r[] = {/* initialize higher level parts of CPU like time base and timers */ cpu_init_r,#endif -#ifdef CONFIG_PPC - initr_spi, -#endif #ifdef CONFIG_CMD_NAND initr_nand,#endif
Signature · 1 line
2.18.0.321.gffc6fa0e3