Add support for DM_USB and DM_USB_DEV to TI's am335x and am43xx_evm platforms

index b6967ff..c91ad2b 100644
@@ -85,7 +85,9 @@ int spl_net_load_image_usb(struct spl_image_info *spl_image,
 			   struct spl_boot_device *bootdev)
 {
 	bootdev->boot_device_name = "usb_ether";
-
+#if CONFIG_IS_ENABLED(DM_USB_GADGET)
+	usb_ether_init();
+#endif
 	return spl_net_load_image(spl_image, bootdev);
 }
 SPL_LOAD_IMAGE_METHOD("USB eth", 0, BOOT_DEVICE_USBETH, spl_net_load_image_usb);

index fd20e8c..be3bb0d 100644
@@ -19,6 +19,11 @@
 #define OMAP_DEV_PHY_PD		BIT(0)
 #define OMAP_USB2_PHY_PD	BIT(28)
 
+#define AM437X_USB2_PHY_PD		BIT(0)
+#define AM437X_USB2_OTG_PD		BIT(1)
+#define AM437X_USB2_OTGVDET_EN		BIT(19)
+#define AM437X_USB2_OTGSESSEND_EN	BIT(20)
+
 #define USB2PHY_DISCON_BYP_LATCH	BIT(31)
 #define USB2PHY_ANA_CONFIG1		(0x4c)
 

@@ -60,6 +65,15 @@ static const struct usb_phy_data dra7x_usb2_phy2_data = {
 	.power_off = OMAP_USB2_PHY_PD,
 };
 
+static const struct usb_phy_data am437x_usb2_data = {
+	.label = "am437x_usb2",
+	.flags =  0,
+	.mask = AM437X_USB2_PHY_PD | AM437X_USB2_OTG_PD |
+		AM437X_USB2_OTGVDET_EN | AM437X_USB2_OTGSESSEND_EN,
+	.power_on = AM437X_USB2_OTGVDET_EN | AM437X_USB2_OTGSESSEND_EN,
+	.power_off = AM437X_USB2_PHY_PD | AM437X_USB2_OTG_PD,
+};
+
 static const struct udevice_id omap_usb2_id_table[] = {
 	{
 		.compatible = "ti,omap5-usb2",

@@ -73,6 +87,10 @@ static const struct udevice_id omap_usb2_id_table[] = {
 		.compatible = "ti,dra7x-usb2-phy2",
 		.data = (ulong)&dra7x_usb2_phy2_data,
 	},
+	{
+		.compatible = "ti,am437x-usb2",
+		.data = (ulong)&am437x_usb2_data,
+	},
 	{},
 };
 

@@ -170,20 +188,25 @@ int omap_usb2_phy_probe(struct udevice *dev)
 	}
 
 	regmap = syscon_regmap_lookup_by_phandle(dev, "syscon-phy-power");
-	if (IS_ERR(regmap)) {
-		printf("can't get regmap (err %ld)\n", PTR_ERR(regmap));
-		return PTR_ERR(regmap);
+	if (!IS_ERR(regmap)) {
+		priv->pwr_regmap = regmap;
+		rc =  dev_read_u32_array(dev, "syscon-phy-power", tmp, 2);
+		if (rc) {
+			printf("couldn't get power reg. offset (err %d)\n", rc);
+			return rc;
+		}
+		priv->pwr_reg_offset = tmp[1];
+		return 0;
 	}
-	priv->pwr_regmap = regmap;
-
-	rc =  dev_read_u32_array(dev, "syscon-phy-power", tmp, 2);
-	if (rc) {
-		printf("couldn't get power reg. offset (err %d)\n", rc);
-		return rc;
+	regmap = syscon_regmap_lookup_by_phandle(dev, "ctrl-module");
+	if (!IS_ERR(regmap)) {
+		priv->pwr_regmap = regmap;
+		priv->pwr_reg_offset = 0;
+		return 0;
 	}
-	priv->pwr_reg_offset = tmp[1];
 
-	return 0;
+	printf("can't get regmap (err %ld)\n", PTR_ERR(regmap));
+	return PTR_ERR(regmap);
 }
 
 U_BOOT_DRIVER(omap_usb2_phy) = {

index 0c189b8..3e6c494 100644
@@ -344,6 +344,7 @@ static const struct udevice_id dwc3_glue_ids[] = {
 	{ .compatible = "xlnx,zynqmp-dwc3" },
 	{ .compatible = "ti,keystone-dwc3"},
 	{ .compatible = "ti,dwc3", .data = (ulong)&ti_ops },
+	{ .compatible = "ti,am437x-dwc3", .data = (ulong)&ti_ops },
 	{ }
 };
 

index 2a59b06..c640708 100644
@@ -681,6 +681,19 @@ int board_init(void)
 }
 
 #ifdef CONFIG_BOARD_LATE_INIT
+#if CONFIG_IS_ENABLED(DM_USB) && CONFIG_IS_ENABLED(OF_CONTROL)
+static int device_okay(const char *path)
+{
+	int node;
+
+	node = fdt_path_offset(gd->fdt_blob, path);
+	if (node < 0)
+		return 0;
+
+	return fdtdec_get_is_enabled(gd->fdt_blob, node);
+}
+#endif
+
 int board_late_init(void)
 {
 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

@@ -693,10 +706,18 @@ int board_late_init(void)
 	if (get_device_type() == HS_DEVICE)
 		env_set("boot_fit", "1");
 #endif
+
+#if CONFIG_IS_ENABLED(DM_USB) && CONFIG_IS_ENABLED(OF_CONTROL)
+	if (device_okay("/ocp/omap_dwc3 at 48380000"))
+		enable_usb_clocks(0);
+	if (device_okay("/ocp/omap_dwc3 at 483c0000"))
+		enable_usb_clocks(1);
+#endif
 	return 0;
 }
 #endif
 
+#if !CONFIG_IS_ENABLED(DM_USB_GADGET)
 #ifdef CONFIG_USB_DWC3
 static struct dwc3_device usb_otg_ss1 = {
 	.maximum_speed = USB_SPEED_HIGH,

@@ -799,6 +820,7 @@ int board_usb_cleanup(int index, enum usb_init_type init)
 	return 0;
 }
 #endif /* defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP) */
+#endif /* !CONFIG_IS_ENABLED(DM_USB_GADGET) */
 
 #ifdef CONFIG_DRIVER_TI_CPSW
 

index 251b4e9..bda099c 100644
@@ -406,7 +406,7 @@ static int am35x_musb_init(struct musb *musb)
 	musb_writel(reg_base, USB_CTRL_REG, AM35X_SOFT_RESET_MASK);
 
 	/* Start the on-chip PHY and its PLL. */
-	if (data->set_phy_power)
+	if (data && data->set_phy_power)
 		data->set_phy_power(data->dev, 1);
 
 	msleep(5);

@@ -437,7 +437,7 @@ static int am35x_musb_exit(struct musb *musb)
 #endif
 
 	/* Shutdown the on-chip PHY and its PLL. */
-	if (data->set_phy_power)
+	if (data && data->set_phy_power)
 		data->set_phy_power(data->dev, 0);
 
 #ifndef __UBOOT__

@@ -628,7 +628,7 @@ static int am35x_suspend(struct device *dev)
 	struct omap_musb_board_data *data = plat->board_data;
 
 	/* Shutdown the on-chip PHY and its PLL. */
-	if (data->set_phy_power)
+	if (data && data->set_phy_power)
 		data->set_phy_power(data->dev, 0);
 
 	clk_disable(glue->phy_clk);

@@ -645,7 +645,7 @@ static int am35x_resume(struct device *dev)
 	int			ret;
 
 	/* Start the on-chip PHY and its PLL. */
-	if (data->set_phy_power)
+	if (data && data->set_phy_power)
 		data->set_phy_power(data->dev, 1);
 
 	ret = clk_enable(glue->phy_clk);

index 9b814f4..0c794b3 100644
@@ -450,7 +450,7 @@ static int dsps_musb_init(struct musb *musb)
 	dsps_writel(reg_base, wrp->control, (1 << wrp->reset));
 
 	/* Start the on-chip PHY and its PLL. */
-	if (data->set_phy_power)
+	if (data && data->set_phy_power)
 		data->set_phy_power(data->dev, 1);
 
 	musb->isr = dsps_interrupt;

@@ -491,7 +491,7 @@ static int dsps_musb_exit(struct musb *musb)
 #endif
 
 	/* Shutdown the on-chip PHY and its PLL. */
-	if (data->set_phy_power)
+	if (data && data->set_phy_power)
 		data->set_phy_power(data->dev, 0);
 
 #ifndef __UBOOT__

@@ -691,7 +691,7 @@ static int dsps_suspend(struct device *dev)
 	struct omap_musb_board_data *data = plat->board_data;
 
 	/* Shutdown the on-chip PHY and its PLL. */
-	if (data->set_phy_power)
+	if (data && data->set_phy_power)
 		data->set_phy_power(data->dev, 0);
 
 	return 0;

@@ -703,7 +703,7 @@ static int dsps_resume(struct device *dev)
 	struct omap_musb_board_data *data = plat->board_data;
 
 	/* Start the on-chip PHY and its PLL. */
-	if (data->set_phy_power)
+	if (data && data->set_phy_power)
 		data->set_phy_power(data->dev, 1);
 
 	return 0;

index 875f100..b40ea00 100644
@@ -7,6 +7,7 @@
 
 #ifndef __ASM_ARM_OMAP_MUSB_H
 #define __ASM_ARM_OMAP_MUSB_H
+#include <linux/usb/musb.h>
 
 extern struct musb_platform_ops musb_dsps_ops;
 extern const struct musb_platform_ops am35x_ops;

@@ -21,4 +22,11 @@ struct omap_musb_board_data {
 };
 
 enum musb_interface    {MUSB_INTERFACE_ULPI, MUSB_INTERFACE_UTMI};
+
+struct ti_musb_platdata {
+	void *base;
+	void *ctrl_mod_base;
+	struct musb_hdrc_platform_data plat;
+};
+
 #endif /* __ASM_ARM_OMAP_MUSB_H */

index 8b6cec1..b35d33f 100644
@@ -1775,6 +1775,14 @@ static int musb_gadget_start(struct usb_gadget *g,
 		struct usb_gadget_driver *driver);
 static int musb_gadget_stop(struct usb_gadget *g,
 		struct usb_gadget_driver *driver);
+#else
+static int musb_gadget_stop(struct usb_gadget *g)
+{
+	struct musb	*musb = gadget_to_musb(g);
+
+	musb_stop(musb);
+	return 0;
+}
 #endif
 
 static const struct usb_gadget_ops musb_gadget_operations = {

@@ -1787,6 +1795,9 @@ static const struct usb_gadget_ops musb_gadget_operations = {
 #ifndef __UBOOT__
 	.udc_start		= musb_gadget_start,
 	.udc_stop		= musb_gadget_stop,
+#else
+	.udc_start		= musb_gadget_start,
+	.udc_stop		= musb_gadget_stop,
 #endif
 };
 

index d40772b..9c8cc6e 100644
@@ -367,7 +367,7 @@ struct dm_usb_ops musb_usb_ops = {
 #endif /* CONFIG_IS_ENABLED(DM_USB) */
 #endif /* CONFIG_USB_MUSB_HOST */
 
-#ifdef CONFIG_USB_MUSB_GADGET
+#if defined(CONFIG_USB_MUSB_GADGET) && !CONFIG_IS_ENABLED(DM_USB_GADGET)
 static struct musb *gadget;
 
 int usb_gadget_handle_interrupts(int index)

@@ -430,7 +430,7 @@ struct musb *musb_register(struct musb_hdrc_platform_data *plat, void *bdata,
 		musbp = &musb_host.host;
 		break;
 #endif
-#ifdef CONFIG_USB_MUSB_GADGET
+#if defined(CONFIG_USB_MUSB_GADGET) && !CONFIG_IS_ENABLED(DM_USB_GADGET)
 	case MUSB_PERIPHERAL:
 		musbp = &gadget;
 		break;

297 lines not on this page · raw message

index f5f2bd5..356e85a 100644
@@ -159,7 +159,55 @@ int cpu_mmc_init(bd_t *bis)
 /* AM33XX has two MUSB controllers which can be host or gadget */
 #if (defined(CONFIG_USB_MUSB_GADGET) || defined(CONFIG_USB_MUSB_HOST)) && \
 	(defined(CONFIG_AM335X_USB0) || defined(CONFIG_AM335X_USB1)) && \
-	(!defined(CONFIG_DM_USB))
+	(!CONFIG_IS_ENABLED(DM_USB) || !CONFIG_IS_ENABLED(OF_CONTROL)) && \
+	(!defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_MUSB_NEW_SUPPORT))
+
+static struct musb_hdrc_config musb_config = {
+	.multipoint     = 1,
+	.dyn_fifo       = 1,
+	.num_eps        = 16,
+	.ram_bits       = 12,
+};
+
+#if CONFIG_IS_ENABLED(DM_USB) && !CONFIG_IS_ENABLED(OF_CONTROL)
+static struct ti_musb_platdata usb0 = {
+	.base = (void *)USB0_OTG_BASE,
+	.ctrl_mod_base = &((struct ctrl_dev *)CTRL_DEVICE_BASE)->usb_ctrl0,
+	.plat = {
+		.config         = &musb_config,
+		.power          = 50,
+		.platform_ops	= &musb_dsps_ops,
+		},
+};
+
+static struct ti_musb_platdata usb1 = {
+	.base = (void *)USB1_OTG_BASE,
+	.ctrl_mod_base = &((struct ctrl_dev *)CTRL_DEVICE_BASE)->usb_ctrl1,
+	.plat = {
+		.config         = &musb_config,
+		.power          = 50,
+		.platform_ops	= &musb_dsps_ops,
+		},
+};
+
+U_BOOT_DEVICES(am33xx_usbs) = {
+#if CONFIG_AM335X_USB0_MODE == MUSB_PERIPHERAL
+	{ "ti-musb-peripheral", &usb0 },
+#elif CONFIG_AM335X_USB0_MODE == MUSB_HOST
+	{ "ti-musb-host", &usb0 },
+#endif
+#if CONFIG_AM335X_USB1_MODE == MUSB_PERIPHERAL
+	{ "ti-musb-peripheral", &usb1 },
+#elif CONFIG_AM335X_USB1_MODE == MUSB_HOST
+	{ "ti-musb-host", &usb1 },
+#endif
+};
+
+int arch_misc_init(void)
+{
+	return 0;
+}
+#else
 static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
 
 /* USB 2.0 PHY Control */

@@ -178,13 +226,6 @@ static void am33xx_usb_set_phy_power(u8 on, u32 *reg_addr)
 	}
 }
 
-static struct musb_hdrc_config musb_config = {
-	.multipoint     = 1,
-	.dyn_fifo       = 1,
-	.num_eps        = 16,
-	.ram_bits       = 12,
-};
-
 #ifdef CONFIG_AM335X_USB0
 static void am33xx_otg0_set_phy_power(struct udevice *dev, u8 on)
 {

@@ -235,6 +276,7 @@ int arch_misc_init(void)
 #endif
 	return 0;
 }
+#endif
 
 #else	/* CONFIG_USB_MUSB_* && CONFIG_AM335X_USB* && !CONFIG_DM_USB */
 

index 5d5b09b..3bd96b9 100644
@@ -253,7 +253,6 @@
 #ifdef CONFIG_SPL_BUILD
 #undef CONFIG_DM_MMC
 #undef CONFIG_TIMER
-#undef CONFIG_DM_USB
 #endif
 
 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_USB_ETHER)