dt-bindings: panel: Add Feiyang FY07024DI26A30-D MIPI-DSI LCD panel
Subsystems (5)
Jagan Teki
maintainerPATCH v3 1/2 dt-bindings: panel: Add Feiyang FY07024DI26A30-D MIPI-DSI LCD panel
Feiyang FY07024DI26A30-D is 1024x600, 4-lane MIPI-DSI LCD panel.
Add dt-bingings for it.
---
Changes for v2:
- none
.../display/panel/feiyang,fy07024di26a30d.txt | 20 +++++++++++++++++++ 1 file changed, 20 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt
Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt new file +20 -0
@@ -0,0 +1,20 @@ +Feiyang FY07024DI26A30-D 7" MIPI-DSI LCD Panel + +Required properties: +- compatible: must be "feiyang,fy07024di26a30d" +- reg: DSI virtual channel used by that screen +- avdd-supply: analog regulator dc1 switch +- dvdd-supply: 3v3 digital regulator +- reset-gpios: a GPIO phandle for the reset pin + +Optional properties: +- backlight: phandle for the backlight control. + +panel@0 { + compatible = "feiyang,fy07024di26a30d"; + reg = <0>; + avdd-supply = <®_dc1sw>; + dvdd-supply = <®_dldo2>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ + backlight = <&backlight>; +};
Signature · 1 line
2.18.0.321.gffc6fa0e3
Jagan Teki
maintainerPATCH v3 2/2 drm/panel: Add Feiyang FY07024DI26A30-D MIPI-DSI LCD panel
Feiyang FY07024DI26A30-D is 1024x600, 4-lane MIPI-DSI LCD panel.
Add panel driver for it.
---
Changes for v2:
- use simple structure for command init
- update proper comments on power, reset delay sequnce
- fix to use set_display_off in disable function
- move mode type to structure
- drop refres rate value, let drm compute
MAINTAINERS | 6 + drivers/gpu/drm/panel/Kconfig | 9 + drivers/gpu/drm/panel/Makefile | 1 + .../drm/panel/panel-feiyang-fy07024di26a30d.c | 296 ++++++++++++++++++ 4 files changed, 312 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c
MAINTAINERS +6 -0
@@ -4732,6 +4732,12 @@ T: git git://anongit.freedesktop.org/drm/drm-misc S: Maintained F: drivers/gpu/drm/tve200/ +DRM DRIVER FOR FEIYANG FY07024DI26A30-D MIPI-DSI LCD PANELS +M: Jagan Teki <[email protected]> +S: Maintained +F: drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c +F: Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt + DRM DRIVER FOR ILITEK ILI9225 PANELS M: David Lechner <[email protected]> S: Maintained
drivers/gpu/drm/panel/Kconfig +9 -0
@@ -38,6 +38,15 @@ config DRM_PANEL_SIMPLE that it can be automatically turned off when the panel goes into a low power state. +config DRM_PANEL_FEIYANG_FY07024DI26A30D + tristate "Feiyang FY07024DI26A30-D MIPI-DSI LCD panel" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y if you want to enable support for panels based on the + Feiyang FY07024DI26A30-D MIPI-DSI interface. + config DRM_PANEL_ILITEK_IL9322 tristate "Ilitek ILI9322 320x240 QVGA panels" depends on OF && SPI
drivers/gpu/drm/panel/Makefile +1 -0
@@ -2,6 +2,7 @@ obj-$(CONFIG_DRM_PANEL_ARM_VERSATILE) += panel-arm-versatile.o obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o +obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +296 -0
296 lines not on this page · raw message
Signature · 1 line
2.18.0.321.gffc6fa0e3
Re: [PATCH v3 2/2] drm/panel: Add Feiyang FY07024DI26A30-D MIPI-DSI LCD panel
Quoted 27 lines · Jagan Teki
Feiyang FY07024DI26A30-D is 1024x600, 4-lane MIPI-DSI LCD panel.
Add panel driver for it.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- use simple structure for command init
- update proper comments on power, reset delay sequnce
- fix to useset_display_offin disable function
- move mode type to structure
- drop refres rate value, let drm computeMAINTAINERS | 6 + drivers/gpu/drm/panel/Kconfig | 9 + drivers/gpu/drm/panel/Makefile | 1 + .../drm/panel/panel-feiyang-fy07024di26a30d.c | 296 ++++++++++++++++++ 4 files changed, 312 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.cMAINTAINERS +0
-0@@ -4732,6 +4732,12 @@ T: git git://anongit.freedesktop.org/drm/drm-misc S: Maintained F: drivers/gpu/drm/tve200/
MAINTAINERS T: git git://anongit.freedesktop.org/drm/drm-misc · line 4743
Quoted 10 lines
MAINTAINERS +6
-0+DRM DRIVER FOR FEIYANG FY07024DI26A30-D MIPI-DSI LCD PANELS +M: Jagan Teki <[email protected]> +S: Maintained +F: drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c +F: Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt + DRM DRIVER FOR ILITEK ILI9225 PANELS M: David Lechner <[email protected]> S: Maintained
As I mentioned on IRC, this will be drm-misc maintained with the other panels, no need to have a dedicated MAINTAINERS entry. You'll get pulled from get_maintainers.pl as a majority commit signer
Quoted 192 lines
drivers/gpu/drm/panel/Kconfig +9
-0@@ -38,6 +38,15 @@ config DRM_PANEL_SIMPLE that it can be automatically turned off when the panel goes into a low power state. +config DRM_PANEL_FEIYANG_FY07024DI26A30D + tristate "Feiyang FY07024DI26A30-D MIPI-DSI LCD panel" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y if you want to enable support for panels based on the + Feiyang FY07024DI26A30-D MIPI-DSI interface. + config DRM_PANEL_ILITEK_IL9322 tristate "Ilitek ILI9322 320x240 QVGA panels" depends on OF && SPIdrivers/gpu/drm/panel/Makefile +1
-0@@ -2,6 +2,7 @@ obj-$(CONFIG_DRM_PANEL_ARM_VERSATILE) += panel-arm-versatile.o obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o +obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.odrivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +154
-0@@ -0,0 +1,296 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2018 Amarula Solutions +* Author: Jagan Teki <[email protected]> +*/ + +#include <linux/backlight.h> +#include <linux/delay.h> +#include <linux/module.h> +#include <linux/of_device.h> + +#include <linux/gpio/consumer.h> +#include <linux/regulator/consumer.h> + +#include <drm/drmP.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_panel.h> + +#define FEIYANG_INIT_CMD_LEN 2 + +struct feiyang { +struct drm_panel panel; +struct mipi_dsi_device *dsi; + +struct backlight_device *backlight; +struct regulator *dvdd; +struct regulator *avdd; +struct gpio_desc *reset; +}; + +static inline struct feiyang *panel_to_feiyang (struct drm_panel *panel) +{ + return container_of(panel, struct feiyang, panel); +} + +struct feiyang_init_cmd { +u8 data[FEIYANG_INIT_CMD_LEN ]; +}; + +static const struct feiyang_init_cmd feiyang_init_cmds[] = { + { .data = {0x80 ,0x58 } }, + { .data = {0x81 ,0x47 } }, + { .data = {0x82 ,0xD4 } }, + { .data = {0x83 ,0x88 } }, + { .data = {0x84 ,0xA9 } }, + { .data = {0x85 ,0xC3 } }, + { .data = {0x86 ,0x82 } }, +}; + +static int feiyang_prepare (struct drm_panel *panel) +{ +struct feiyang *ctx =panel_to_feiyang (panel); +struct mipi_dsi_device *dsi = ctx->dsi; +unsigned int i; +int ret; + + ret =regulator_enable (ctx->dvdd); +if (ret) +return ret; + +/* T1 (dvdd start + dvdd rise) 0 < T1 <= 10ms */ +msleep (10 ); + + ret =regulator_enable (ctx->avdd); +if (ret) +return ret; + +/* T3 (dvdd rise + avdd start + avdd rise) T3 >= 20ms */ +msleep (20 ); + +gpiod_set_value (ctx->reset,1 ); +msleep (50 ); + +gpiod_set_value (ctx->reset,0 ); +/* T5 + T6 (avdd rise + video & logic signal rise) +* T5 >= 10ms, 0 < T6 <= 10ms +*/ +msleep (20 ); + +gpiod_set_value (ctx->reset,1 ); + +/* T12 (video & logic signal rise + backlight rise) T12 >= 200ms */ +msleep (200 ); + +for (i =0 ; i <ARRAY_SIZE (feiyang_init_cmds); i++) { +const struct feiyang_init_cmd *cmd = + &feiyang_init_cmds[i]; + + ret =mipi_dsi_dcs_write_buffer (dsi, cmd->data, +FEIYANG_INIT_CMD_LEN ); +if (ret <0 ) +return ret; + } + +return 0 ; +} + +static int feiyang_enable (struct drm_panel *panel) +{ +struct feiyang *ctx =panel_to_feiyang (panel); + +/* T12 (video & logic signal rise + backlight rise) T12 >= 200ms */ +msleep (200 ); + +mipi_dsi_dcs_set_display_on (ctx->dsi); +backlight_enable (ctx->backlight); + +return 0 ; +} + +static int feiyang_disable (struct drm_panel *panel) +{ +struct feiyang *ctx =panel_to_feiyang (panel); + +backlight_disable (ctx->backlight); +return mipi_dsi_dcs_set_display_off (ctx->dsi); +} + +static int feiyang_unprepare (struct drm_panel *panel) +{ +struct feiyang *ctx =panel_to_feiyang (panel); +int ret; + + ret =mipi_dsi_dcs_set_display_off (ctx->dsi); +if (ret <0 ) +DRM_DEV_ERROR (panel->dev,"failed to set display off: %d\n" , + ret); + + ret =mipi_dsi_dcs_enter_sleep_mode (ctx->dsi); +if (ret <0 ) +DRM_DEV_ERROR (panel->dev,"failed to enter sleep mode: %d\n" , + ret); + +/* T13 (backlight fall + video & logic signal fall) T13 >= 200ms */ +msleep (200 ); + +gpiod_set_value (ctx->reset,0 ); + +gpiod_set_value (ctx->reset,1 ); + +gpiod_set_value (ctx->reset,0 ); + +regulator_disable (ctx->avdd); + +/* T11 (dvdd rise to fall) 0 < T11 <= 10ms */ +msleep (10 ); + +regulator_disable (ctx->dvdd); + +return 0 ; +} + +static const struct drm_display_mode feiyang_default_mode = { + .clock =55000 ,
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c line 164
Quoted 10 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +10
-0+ + .hdisplay = 1024, + .hsync_start = 1024 + 396, + .hsync_end = 1024 + 396 + 20, + .htotal = 1024 + 396 + 20 + 100, + + .vdisplay = 600, + .vsync_start = 600 + 12, + .vsync_end = 600 + 12 + 2, + .vtotal = 600 + 12 + 2 + 21,
These timings are still incorrect, they'll give a 56.2Hz refresh rate. Is that really what you want?
Quoted 135 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +132
-0+ + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, +}; + +static int feiyang_get_modes (struct drm_panel *panel) +{ +struct drm_connector *connector = panel->connector; +struct feiyang *ctx =panel_to_feiyang (panel); +struct drm_display_mode *mode; + + mode =drm_mode_duplicate (panel->drm, &feiyang_default_mode); +if (!mode) { +DRM_DEV_ERROR (&ctx->dsi->dev,"failed to add mode %ux%ux@%u\n" , + feiyang_default_mode.hdisplay, + feiyang_default_mode.vdisplay, + feiyang_default_mode.vrefresh); +return -ENOMEM ; + } + +drm_mode_set_name (mode); + +drm_mode_probed_add (connector, mode); + +return 1 ; +} + +static const struct drm_panel_funcs feiyang_funcs = { + .disable = feiyang_disable, + .unprepare = feiyang_unprepare, + .prepare = feiyang_prepare, + .enable = feiyang_enable, + .get_modes = feiyang_get_modes, +}; + +static int feiyang_dsi_probe (struct mipi_dsi_device *dsi) +{ +struct device_node *np; +struct feiyang *ctx; +int ret; + + ctx =devm_kzalloc (&dsi->dev,sizeof (*ctx),GFP_KERNEL ); +if (!ctx) +return -ENOMEM ; +mipi_dsi_set_drvdata (dsi, ctx); + ctx->dsi = dsi; + +drm_panel_init (&ctx->panel); + ctx->panel.dev = &dsi->dev; + ctx->panel.funcs = &feiyang_funcs; + + ctx->dvdd =devm_regulator_get (&dsi->dev,"dvdd" ); +if (IS_ERR (ctx->dvdd)) { +DRM_DEV_ERROR (&dsi->dev,"Couldn't get dvdd regulator\n" ); +return PTR_ERR (ctx->dvdd); + } + + ctx->avdd =devm_regulator_get (&dsi->dev,"avdd" ); +if (IS_ERR (ctx->avdd)) { +DRM_DEV_ERROR (&dsi->dev,"Couldn't get avdd regulator\n" ); +return PTR_ERR (ctx->avdd); + } + + ctx->reset =devm_gpiod_get (&dsi->dev,"reset" ,GPIOD_OUT_LOW ); +if (IS_ERR (ctx->reset)) { +DRM_DEV_ERROR (&dsi->dev,"Couldn't get our reset GPIO\n" ); +return PTR_ERR (ctx->reset); + } + + np =of_parse_phandle (dsi->dev.of_node,"backlight" ,0 ); +if (np) { + ctx->backlight =of_find_backlight_by_node (np); +of_node_put (np); + +if (!ctx->backlight) +return -EPROBE_DEFER ; + } + + ret =drm_panel_add (&ctx->panel); +if (ret <0 ) + goto put_backlight; + + dsi->mode_flags =MIPI_DSI_MODE_VIDEO_BURST ; + dsi->format =MIPI_DSI_FMT_RGB888 ; + dsi->lanes =4 ; + + ret =mipi_dsi_attach (dsi); +if (ret <0 ) + goto panel_remove; + +return ret; + +panel_remove: +drm_panel_remove (&ctx->panel); +put_backlight: +if (ctx->backlight) +put_device (&ctx->backlight->dev); + +return ret; +} + +static int feiyang_dsi_remove (struct mipi_dsi_device *dsi) +{ +struct feiyang *ctx =mipi_dsi_get_drvdata (dsi); + +mipi_dsi_detach (dsi); +drm_panel_remove (&ctx->panel); + +if (ctx->backlight) +put_device (&ctx->backlight->dev); + +return 0 ; +} + +static const struct of_device_id feiyang_of_match[] = { + { .compatible ="feiyang,fy07024di26a30d" , }, + { } +}; +MODULE_DEVICE_TABLE (of, feiyang_of_match); + +static struct mipi_dsi_driver feiyang_driver = { + .probe = feiyang_dsi_probe, + .remove = feiyang_dsi_remove, + .driver = { + .name ="feiyang-fy07024di26a30d" , + .of_match_table = feiyang_of_match, + }, +}; +module_mipi_dsi_driver (feiyang_driver); + +MODULE_AUTHOR ("Jagan Teki <[email protected]>" ); +MODULE_DESCRIPTION ("Feiyang FY07024DI26A30-D MIPI-DSI LCD panel" ); +MODULE_LICENSE ("GPL" );Signature · 1 line
2.18.0.321.gffc6fa0e3
Signature · 5 lines
Sean Paul, Software Engineer, Google / Chromium OS _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Jagan Teki
maintainerRe: [PATCH v3 2/2] drm/panel: Add Feiyang FY07024DI26A30-D MIPI-DSI LCD panel
Quoted 30 lines · Sean Paul
Quoted 28 lines · Jagan Teki
Feiyang FY07024DI26A30-D is 1024x600, 4-lane MIPI-DSI LCD panel.
Add panel driver for it.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- use simple structure for command init
- update proper comments on power, reset delay sequnce
- fix to useset_display_offin disable function
- move mode type to structure
- drop refres rate value, let drm computeMAINTAINERS | 6 + drivers/gpu/drm/panel/Kconfig | 9 + drivers/gpu/drm/panel/Makefile | 1 + .../drm/panel/panel-feiyang-fy07024di26a30d.c | 296 ++++++++++++++++++ 4 files changed, 312 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.cMAINTAINERS +0
-0@@ -4732,6 +4732,12 @@ T: git git://anongit.freedesktop.org/drm/drm-misc S: Maintained F: drivers/gpu/drm/tve200/
Quoted 13 lines
MAINTAINERS T: git git://anongit.freedesktop.org/drm/drm-misc · line 4743
Quoted 9 lines
MAINTAINERS +6
-0+DRM DRIVER FOR FEIYANG FY07024DI26A30-D MIPI-DSI LCD PANELS +M: Jagan Teki <[email protected]> +S: Maintained +F: drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c +F: Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt + DRM DRIVER FOR ILITEK ILI9225 PANELS M: David Lechner <[email protected]> S: MaintainedAs I mentioned on IRC, this will be drm-misc maintained with the other panels, no need to have a dedicated
MAINTAINERSentry. You'll get pulled from get_maintainers.pl as a majority commit signer
This I missed it on IRC, sorry will drop.
Quoted 198 lines
Quoted 198 lines
drivers/gpu/drm/panel/Kconfig +9
-0@@ -38,6 +38,15 @@ config DRM_PANEL_SIMPLE that it can be automatically turned off when the panel goes into a low power state. +config DRM_PANEL_FEIYANG_FY07024DI26A30D + tristate "Feiyang FY07024DI26A30-D MIPI-DSI LCD panel" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y if you want to enable support for panels based on the + Feiyang FY07024DI26A30-D MIPI-DSI interface. + config DRM_PANEL_ILITEK_IL9322 tristate "Ilitek ILI9322 320x240 QVGA panels" depends on OF && SPIdrivers/gpu/drm/panel/Makefile +1
-0@@ -2,6 +2,7 @@ obj-$(CONFIG_DRM_PANEL_ARM_VERSATILE) += panel-arm-versatile.o obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o +obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.odrivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +159
-0@@ -0,0 +1,296 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2018 Amarula Solutions +* Author: Jagan Teki <[email protected]> +*/ + +#include <linux/backlight.h> +#include <linux/delay.h> +#include <linux/module.h> +#include <linux/of_device.h> + +#include <linux/gpio/consumer.h> +#include <linux/regulator/consumer.h> + +#include <drm/drmP.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_panel.h> + +#define FEIYANG_INIT_CMD_LEN 2 + +struct feiyang { +struct drm_panel panel; +struct mipi_dsi_device *dsi; + +struct backlight_device *backlight; +struct regulator *dvdd; +struct regulator *avdd; +struct gpio_desc *reset; +}; + +static inline struct feiyang *panel_to_feiyang (struct drm_panel *panel) +{ + return container_of(panel, struct feiyang, panel); +} + +struct feiyang_init_cmd { +u8 data[FEIYANG_INIT_CMD_LEN ]; +}; + +static const struct feiyang_init_cmd feiyang_init_cmds[] = { + { .data = {0x80 ,0x58 } }, + { .data = {0x81 ,0x47 } }, + { .data = {0x82 ,0xD4 } }, + { .data = {0x83 ,0x88 } }, + { .data = {0x84 ,0xA9 } }, + { .data = {0x85 ,0xC3 } }, + { .data = {0x86 ,0x82 } }, +}; + +static int feiyang_prepare (struct drm_panel *panel) +{ +struct feiyang *ctx =panel_to_feiyang (panel); +struct mipi_dsi_device *dsi = ctx->dsi; +unsigned int i; +int ret; + + ret =regulator_enable (ctx->dvdd); +if (ret) +return ret; + +/* T1 (dvdd start + dvdd rise) 0 < T1 <= 10ms */ +msleep (10 ); + + ret =regulator_enable (ctx->avdd); +if (ret) +return ret; + +/* T3 (dvdd rise + avdd start + avdd rise) T3 >= 20ms */ +msleep (20 ); + +gpiod_set_value (ctx->reset,1 ); +msleep (50 ); + +gpiod_set_value (ctx->reset,0 ); +/* T5 + T6 (avdd rise + video & logic signal rise) +* T5 >= 10ms, 0 < T6 <= 10ms +*/ +msleep (20 ); + +gpiod_set_value (ctx->reset,1 ); + +/* T12 (video & logic signal rise + backlight rise) T12 >= 200ms */ +msleep (200 ); + +for (i =0 ; i <ARRAY_SIZE (feiyang_init_cmds); i++) { +const struct feiyang_init_cmd *cmd = + &feiyang_init_cmds[i]; + + ret =mipi_dsi_dcs_write_buffer (dsi, cmd->data, +FEIYANG_INIT_CMD_LEN ); +if (ret <0 ) +return ret; + } + +return 0 ; +} + +static int feiyang_enable (struct drm_panel *panel) +{ +struct feiyang *ctx =panel_to_feiyang (panel); + +/* T12 (video & logic signal rise + backlight rise) T12 >= 200ms */ +msleep (200 ); + +mipi_dsi_dcs_set_display_on (ctx->dsi); +backlight_enable (ctx->backlight); + +return 0 ; +} + +static int feiyang_disable (struct drm_panel *panel) +{ +struct feiyang *ctx =panel_to_feiyang (panel); + +backlight_disable (ctx->backlight); +return mipi_dsi_dcs_set_display_off (ctx->dsi); +} + +static int feiyang_unprepare (struct drm_panel *panel) +{ +struct feiyang *ctx =panel_to_feiyang (panel); +int ret; + + ret =mipi_dsi_dcs_set_display_off (ctx->dsi); +if (ret <0 ) +DRM_DEV_ERROR (panel->dev,"failed to set display off: %d\n" , + ret); + + ret =mipi_dsi_dcs_enter_sleep_mode (ctx->dsi); +if (ret <0 ) +DRM_DEV_ERROR (panel->dev,"failed to enter sleep mode: %d\n" , + ret); + +/* T13 (backlight fall + video & logic signal fall) T13 >= 200ms */ +msleep (200 ); + +gpiod_set_value (ctx->reset,0 ); + +gpiod_set_value (ctx->reset,1 ); + +gpiod_set_value (ctx->reset,0 ); + +regulator_disable (ctx->avdd); + +/* T11 (dvdd rise to fall) 0 < T11 <= 10ms */ +msleep (10 ); + +regulator_disable (ctx->dvdd); + +return 0 ; +} + +static const struct drm_display_mode feiyang_default_mode = { + .clock =55000 , + + .hdisplay =1024 , + .hsync_start =1024 +396 , + .hsync_end =1024 +396 +20 , + .htotal =1024 +396 +20 +100 ,
Quoted 8 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c line 164
Quoted 5 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +5
-0+ + .vdisplay = 600, + .vsync_start = 600 + 12, + .vsync_end = 600 + 12 + 2, + .vtotal = 600 + 12 + 2 + 21,These timings are still incorrect, they'll give a 56.2Hz refresh rate. Is that really what you want?
I would like to go with same rate as of now since BSP is using the same, since I don't have any information from chip vendor(even I wrote it and waiting for response). I will update accordingly once I get the information from vendor.
Let me know your inputs.
Re: [PATCH v3 2/2] drm/panel: Add Feiyang FY07024DI26A30-D MIPI-DSI LCD panel
Quoted 78 lines · Jagan Teki
Quoted 30 lines · Sean Paul
Quoted 28 lines · Jagan Teki
Feiyang FY07024DI26A30-D is 1024x600, 4-lane MIPI-DSI LCD panel.
Add panel driver for it.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- use simple structure for command init
- update proper comments on power, reset delay sequnce
- fix to useset_display_offin disable function
- move mode type to structure
- drop refres rate value, let drm computeMAINTAINERS | 6 + drivers/gpu/drm/panel/Kconfig | 9 + drivers/gpu/drm/panel/Makefile | 1 + .../drm/panel/panel-feiyang-fy07024di26a30d.c | 296 ++++++++++++++++++ 4 files changed, 312 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.cMAINTAINERS +0
-0@@ -4732,6 +4732,12 @@ T: git git://anongit.freedesktop.org/drm/drm-misc S: Maintained F: drivers/gpu/drm/tve200/Quoted 13 lines
MAINTAINERS T: git git://anongit.freedesktop.org/drm/drm-misc · line 4743
Quoted 9 lines
MAINTAINERS +6
-0+DRM DRIVER FOR FEIYANG FY07024DI26A30-D MIPI-DSI LCD PANELS +M: Jagan Teki <[email protected]> +S: Maintained +F: drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c +F: Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt + DRM DRIVER FOR ILITEK ILI9225 PANELS M: David Lechner <[email protected]> S: MaintainedAs I mentioned on IRC, this will be drm-misc maintained with the other panels, no need to have a dedicated
MAINTAINERSentry. You'll get pulled from get_maintainers.pl as a majority commit signerThis I missed it on IRC, sorry will drop.
Quoted 31 lines
Quoted 31 lines
drivers/gpu/drm/panel/Kconfig +9
-0@@ -38,6 +38,15 @@ config DRM_PANEL_SIMPLE that it can be automatically turned off when the panel goes into a low power state. +config DRM_PANEL_FEIYANG_FY07024DI26A30D + tristate "Feiyang FY07024DI26A30-D MIPI-DSI LCD panel" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y if you want to enable support for panels based on the + Feiyang FY07024DI26A30-D MIPI-DSI interface. + config DRM_PANEL_ILITEK_IL9322 tristate "Ilitek ILI9322 320x240 QVGA panels" depends on OF && SPIdrivers/gpu/drm/panel/Makefile +1
-0@@ -2,6 +2,7 @@ obj-$(CONFIG_DRM_PANEL_ARM_VERSATILE) += panel-arm-versatile.o obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o +obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o
Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c
Quoted 8 lines
drivers/gpu/drm/panel/Makefile +0
-0obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.odrivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +0
-0@@ -0,0 +1,296 @@
/snip
Quoted 16 lines
Quoted 7 lines
Quoted 7 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +7
-0+static const struct drm_display_mode feiyang_default_mode = { + .clock =55000 , + + .hdisplay =1024 , + .hsync_start =1024 +396 , + .hsync_end =1024 +396 +20 , + .htotal =1024 +396 +20 +100 ,Quoted 8 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c line 164
Quoted 5 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +5
-0+ + .vdisplay = 600, + .vsync_start = 600 + 12, + .vsync_end = 600 + 12 + 2, + .vtotal = 600 + 12 + 2 + 21,These timings are still incorrect, they'll give a 56.2Hz refresh rate. Is that really what you want?
Quoted 6 lines
I would like to go with same rate as of now since BSP is using the same, since I don't have any information from chip vendor(even I wrote it and waiting for response). I will update accordingly once I get the information from vendor.
Let me know your inputs.
Not totally on board with this, tbh. It seems wrong, so I'm not sure why we'd apply code that seems wrong. We're not in a rush, we've already cut 4.21, so I think we should just wait for vendor confirmation on these values.
Sean
Signature · 5 lines
Sean Paul, Software Engineer, Google / Chromium OS _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Jagan Teki
maintainerRe: [PATCH v3 2/2] drm/panel: Add Feiyang FY07024DI26A30-D MIPI-DSI LCD panel
Quoted 112 lines · Sean Paul
Quoted 78 lines · Jagan Teki
Quoted 30 lines · Sean Paul
Quoted 28 lines · Jagan Teki
Feiyang FY07024DI26A30-D is 1024x600, 4-lane MIPI-DSI LCD panel.
Add panel driver for it.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- use simple structure for command init
- update proper comments on power, reset delay sequnce
- fix to useset_display_offin disable function
- move mode type to structure
- drop refres rate value, let drm computeMAINTAINERS | 6 + drivers/gpu/drm/panel/Kconfig | 9 + drivers/gpu/drm/panel/Makefile | 1 + .../drm/panel/panel-feiyang-fy07024di26a30d.c | 296 ++++++++++++++++++ 4 files changed, 312 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.cMAINTAINERS +0
-0@@ -4732,6 +4732,12 @@ T: git git://anongit.freedesktop.org/drm/drm-misc S: Maintained F: drivers/gpu/drm/tve200/Quoted 13 lines
MAINTAINERS T: git git://anongit.freedesktop.org/drm/drm-misc · line 4743
Quoted 9 lines
MAINTAINERS +6
-0+DRM DRIVER FOR FEIYANG FY07024DI26A30-D MIPI-DSI LCD PANELS +M: Jagan Teki <[email protected]> +S: Maintained +F: drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c +F: Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt + DRM DRIVER FOR ILITEK ILI9225 PANELS M: David Lechner <[email protected]> S: MaintainedAs I mentioned on IRC, this will be drm-misc maintained with the other panels, no need to have a dedicated
MAINTAINERSentry. You'll get pulled from get_maintainers.pl as a majority commit signerThis I missed it on IRC, sorry will drop.
Quoted 31 lines
Quoted 31 lines
drivers/gpu/drm/panel/Kconfig +9
-0@@ -38,6 +38,15 @@ config DRM_PANEL_SIMPLE that it can be automatically turned off when the panel goes into a low power state. +config DRM_PANEL_FEIYANG_FY07024DI26A30D + tristate "Feiyang FY07024DI26A30-D MIPI-DSI LCD panel" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + help + Say Y if you want to enable support for panels based on the + Feiyang FY07024DI26A30-D MIPI-DSI interface. + config DRM_PANEL_ILITEK_IL9322 tristate "Ilitek ILI9322 320x240 QVGA panels" depends on OF && SPIdrivers/gpu/drm/panel/Makefile +1
-0@@ -2,6 +2,7 @@ obj-$(CONFIG_DRM_PANEL_ARM_VERSATILE) += panel-arm-versatile.o obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o +obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.oQuoted 8 lines
Quoted 8 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c
Quoted 8 lines
drivers/gpu/drm/panel/Makefile +0
-0obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.odrivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +0
-0@@ -0,0 +1,296 @@/snip
Quoted 21 lines
Quoted 7 lines
Quoted 7 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +7
-0+static const struct drm_display_mode feiyang_default_mode = { + .clock =55000 , + + .hdisplay =1024 , + .hsync_start =1024 +396 , + .hsync_end =1024 +396 +20 , + .htotal =1024 +396 +20 +100 ,Quoted 8 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c line 164
Quoted 5 lines
drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c new file +5
-0+ + .vdisplay = 600, + .vsync_start = 600 + 12, + .vsync_end = 600 + 12 + 2, + .vtotal = 600 + 12 + 2 + 21,These timings are still incorrect, they'll give a 56.2Hz refresh rate. Is that really what you want?
I would like to go with same rate as of now since BSP is using the same, since I don't have any information from chip vendor(even I wrote it and waiting for response). I will update accordingly once I get the information from vendor.
Quoted 5 lines
Quoted 1 line
Let me know your inputs.
Not totally on board with this, tbh. It seems wrong, so I'm not sure why we'd apply code that seems wrong. We're not in a rush, we've already cut 4.21, so I think we should just wait for vendor confirmation on these values.
No, I'm not asking to apply just to know how it works and more over I can see some panels still use refresh rate 60 but with wrong panel timings.
Anyway, I've managed to satisfy the refresh rate 60 with changed porch values. Here are new timings.
.clock = 55000,
.hdisplay = 1024,
.hsync_start = 1024 + 310,
.hsync_end = 1024 + 310 + 20,
.htotal = 1024 + 310 + 20 + 90,
.vdisplay = 600,
.vsync_start = 600 + 12,
.vsync_end = 600 + 12 + 2,
.vtotal = 600 + 12 + 2 + 21I can see the display as same as before, but not clear is there anyway to update porch values for desired refresh rate computation.
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel