include: configs: Add gunzip size for HiKey board
Subsystems (2)
PATCH v2 1/3 include: configs: Add gunzip size for HiKey board
From: Manivannan Sadhasivam <[email protected]>
Default 8MB gunzip size is not enough to load the release kernel, hence fix 64MB size for uncompressing the kernel.
---
Changes in v2: Added Simon's Reviewed-by tag.
include/configs/hikey.h | 2 ++ 1 file changed, 2 insertions(+)
include/configs/hikey.h +2 -0
@@ -18,6 +18,8 @@#define CONFIG_REMAKE_ELF +#define CONFIG_SYS_BOOTM_LEN SZ_64M +/* Physical Memory Map */ /* CONFIG_SYS_TEXT_BASE needs to align with where ATF loads bl33.bin */
Signature · 1 line
2.17.1
PATCH v2 2/3 mmc: Convert HI6220 MMC driver to driver model
From: Manivannan Sadhasivam <[email protected]>
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver model.
---
Changes in v2: Added Simon's Reviewed-by tag.
configs/hikey_defconfig | 1 + drivers/mmc/hi6220_dw_mmc.c | 100 +++++++++++++++++++++++++----------- 2 files changed, 70 insertions(+), 31 deletions(-)
configs/hikey_defconfig +1 -0
@@ -18,6 +18,7 @@ CONFIG_DEFAULT_DEVICE_TREE="hi6220-hikey" CONFIG_ENV_IS_IN_FAT=y CONFIG_ENV_FAT_INTERFACE="mmc" CONFIG_ENV_FAT_DEVICE_AND_PART="1:1" +CONFIG_DM_MMC=y CONFIG_MMC_DW=y CONFIG_MMC_DW_K3=y CONFIG_CONS_INDEX=4
drivers/mmc/hi6220_dw_mmc.c +69 -31
120 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v2 2/3 mmc: Convert HI6220 MMC driver to driver model
Quoted 152 lines · Manivannan Sadhasivam
From: Manivannan Sadhasivam <[email protected]>
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver model.
Signed-off-by Manivannan Sadhasivam <[email protected]>Reviewed-by Simon Glass <[email protected]>---
Changes in v2: Added Simon's Reviewed-by tag.
configs/hikey_defconfig | 1 + drivers/mmc/hi6220_dw_mmc.c | 100 +++++++++++++++++++++++++----------- 2 files changed, 70 insertions(+), 31 deletions(-)configs/hikey_defconfig +1
-0@@ -18,6 +18,7 @@ CONFIG_DEFAULT_DEVICE_TREE="hi6220-hikey" CONFIG_ENV_IS_IN_FAT=y CONFIG_ENV_FAT_INTERFACE="mmc" CONFIG_ENV_FAT_DEVICE_AND_PART="1:1" +CONFIG_DM_MMC=y CONFIG_MMC_DW=y CONFIG_MMC_DW_K3=y CONFIG_CONS_INDEX=4drivers/mmc/hi6220_dw_mmc.c +69
-31@@ -5,51 +5,89 @@*/ #include <common.h> +#include <dm.h> #include <dwmmc.h> +#include <errno.h> +#include <fdtdec.h> #include <malloc.h> -#include <linux/errno.h> -#define DWMMC_MAX_CH_NUM 4 +DECLARE_GLOBAL_DATA_PTR ; -#define DWMMC_MAX_FREQ 50000000 -#define DWMMC_MIN_FREQ 400000 +struct hi6220_dwmmc_plat { +struct mmc_config cfg; +struct mmc mmc; +}; -/* Source clock is configured to 100MHz by ATF bl1*/ -#define MMC0_DEFAULT_FREQ 100000000 +struct hi6220_dwmmc_priv_data { +struct dwmci_host host; +}; -static int hi6220_dwmci_core_init (struct dwmci_host *host,int index) +static int hi6220_dwmmc_ofdata_to_platdata (struct udevice *dev) { - host->name ="Hisilicon DWMMC" ; +struct hi6220_dwmmc_priv_data *priv =dev_get_priv (dev); +struct dwmci_host *host = &priv->host; - host->dev_index = index; + host->name = dev->name; + host->ioaddr = (void *)devfdt_get_addr (dev); + host->buswidth =fdtdec_get_int (gd->fdt_blob,dev_of_offset (dev), +"bus-width" ,4 ); + +/* use non-removable property for differentiating SD card and eMMC */ +if (dev_read_bool (dev,"non-removable" )) + host->dev_index =0 ; +else + host->dev_index =1 ; + + host->priv = priv; -/* Add the mmc channel to be registered with mmc core */ -if (add_dwmci (host,DWMMC_MAX_FREQ ,DWMMC_MIN_FREQ )) { -printf ("DWMMC%d registration failed\n" , index); -return -1 ; - }return 0 ; } -/* -* This function adds the mmc channel to be registered with mmc core. -* index - mmc channel number. -* regbase - register base address of mmc channel specified in 'index'. -* bus_width - operating bus width of mmc channel specified in 'index'. -*/ -int hi6220_dwmci_add_port (int index,u32 regbase,int bus_width) +static int hi6220_dwmmc_probe (struct udevice *dev) { -struct dwmci_host *host =NULL ; +struct hi6220_dwmmc_plat *plat =dev_get_platdata (dev); +struct mmc_uclass_priv *upriv =dev_get_uclass_priv (dev); +struct hi6220_dwmmc_priv_data *priv =dev_get_priv (dev); +struct dwmci_host *host = &priv->host; - host =calloc (1 ,sizeof (struct dwmci_host )); -if (!host) { -pr_err ("dwmci_host calloc failed!\n" ); -return -ENOMEM ; - } +/* Use default bus speed due to absence of clk driver */ + host->bus_hz =50000000 ; - host->ioaddr = (void *)(ulong )regbase; - host->buswidth = bus_width; - host->bus_hz =MMC0_DEFAULT_FREQ ; +dwmci_setup_cfg (&plat->cfg, host, host->bus_hz,400000 ); + host->mmc = &plat->mmc; -return hi6220_dwmci_core_init (host, index); + host->mmc->priv = &priv->host; + upriv->mmc = host->mmc; + host->mmc->dev = dev; + +return dwmci_probe (dev); } + +static int hi6220_dwmmc_bind (struct udevice *dev) +{ +struct hi6220_dwmmc_plat *plat =dev_get_platdata (dev); +int ret; + + ret =dwmci_bind (dev, &plat->mmc, &plat->cfg); +if (ret) +return ret; + +return 0 ; +} + +static const struct udevice_id hi6220_dwmmc_ids[] = { + { .compatible ="hisilicon,hi6220-dw-mshc" }, + { } +}; + +U_BOOT_DRIVER (hi6220_dwmmc_drv) = { + .name ="hi6220_dwmmc" , + .id =UCLASS_MMC , + .of_match = hi6220_dwmmc_ids, + .ofdata_to_platdata = hi6220_dwmmc_ofdata_to_platdata, + .ops = &dm_dwmci_ops, + .bind = hi6220_dwmmc_bind, + .probe = hi6220_dwmmc_probe, + .priv_auto_alloc_size =sizeof (struct hi6220_dwmmc_priv_data ), + .platdata_auto_alloc_size =sizeof (struct hi6220_dwmmc_plat ), +};
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190115/b5b19b81/attachment.sig>
PATCH v2 2/3 mmc: Convert HI6220 MMC driver to driver model
In reply to Manivannan SadhasivamQuoted 7 lines · Manivannan Sadhasivam
From: Manivannan Sadhasivam <[email protected]>
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver model.
Signed-off-by Manivannan Sadhasivam <[email protected]>Reviewed-by Simon Glass <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190115/81e6a182/attachment.sig>
PATCH v2 3/3 arm: dts: Add MMC nodes for HiKey board
In reply to Manivannan SadhasivamFrom: Manivannan Sadhasivam <[email protected]>
Add MMC nodes for HiKey board based on HI6220 SoC. There are three MMC controllers in this SoC, first one used for eMMC, second one used for SD card and third one is not used by u-boot.
---
Changes in v2:
* Added hi6220-hikey-u-boot.dtsi for u-boot additions as per Tom's comment.
* Added Simon's Reviewed-by tag.
arch/arm/dts/hi6220-hikey-u-boot.dtsi | 14 ++++++++++++++ arch/arm/dts/hi6220-hikey.dts | 11 +++++++++++ arch/arm/dts/hi6220.dtsi | 18 ++++++++++++++++++ 3 files changed, 43 insertions(+) create mode 100644 arch/arm/dts/hi6220-hikey-u-boot.dtsi
arch/arm/dts/hi6220-hikey-u-boot.dtsi new file +14 -0
@@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * U-Boot additions + * + * Copyright (c) 2018 Linaro Ltd. + */ + +&mmc0 { + u-boot,dm-pre-reloc; +}; + +&mmc1 { + u-boot,dm-pre-reloc; +};
arch/arm/dts/hi6220-hikey.dts +11 -0
@@ -40,6 +40,17 @@ }; }; +&mmc0 { + status = "okay"; + non-removable; + bus-width = <8>; +}; + +&mmc1 { + status = "okay"; + bus-width = <4>; +}; + &uart2 { label = "LS-UART0"; };
arch/arm/dts/hi6220.dtsi +18 -0
@@ -162,6 +162,24 @@ #clock-cells = <1>; }; + mmc0: dwmmc at f723d000 { + compatible = "hisilicon,hi6220-dw-mshc"; + reg = <0x0 0xf723d000 0x0 0x1000>; + interrupts = <0x0 0x48 0x4>; + clocks = <&sys_ctrl 2>, <&sys_ctrl 1>; + clock-names = "ciu", "biu"; + status = "disabled"; + }; + + mmc1: dwmmc at f723e000 { + compatible = "hisilicon,hi6220-dw-mshc"; + reg = <0x0 0xf723e000 0x0 0x1000>; + interrupts = <0x0 0x49 0x4>; + clocks = <&sys_ctrl 4>, <&sys_ctrl 3>; + clock-names = "ciu", "biu"; + status = "disabled"; + }; + uart0: uart at f8015000 { /* console */ compatible = "arm,pl011", "arm,primecell"; reg = <0x0 0xf8015000 0x0 0x1000>;
Signature · 1 line
2.17.1
PATCH v2 3/3 arm: dts: Add MMC nodes for HiKey board
Quoted 8 lines · Manivannan Sadhasivam
From: Manivannan Sadhasivam <[email protected]>
Add MMC nodes for HiKey board based on HI6220 SoC. There are three MMC controllers in this SoC, first one used for eMMC, second one used for SD card and third one is not used by u-boot.
Signed-off-by Manivannan Sadhasivam <[email protected]>Reviewed-by Simon Glass <[email protected]>
But can you please do a follow-up series that syncs the DT files with say Linux v4.20? Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20181227/d68cadbb/attachment.sig>
PATCH v2 3/3 arm: dts: Add MMC nodes for HiKey board
Quoted 8 lines · Tom Rini
Quoted 6 lines · Manivannan Sadhasivam
From: Manivannan Sadhasivam <[email protected]>
Add MMC nodes for HiKey board based on HI6220 SoC. There are three MMC controllers in this SoC, first one used for eMMC, second one used for SD card and third one is not used by u-boot.
Quoted 8 lines
Quoted 2 lines
Signed-off-by Manivannan Sadhasivam <[email protected]>Reviewed-by Simon Glass <[email protected]>Reviewed-by Tom Rini <[email protected]>But can you please do a follow-up series that syncs the DT files with say Linux v4.20? Thanks!
Sure, will do as a part of the follow up series which converts USB driver to driver model.
Thanks,
Mani
Quoted 2 lines
Signature · 1 line
Tom
PATCH v2 3/3 arm: dts: Add MMC nodes for HiKey board
In reply to Manivannan SadhasivamQuoted 9 lines · Manivannan Sadhasivam
From: Manivannan Sadhasivam <[email protected]>
Add MMC nodes for HiKey board based on HI6220 SoC. There are three MMC controllers in this SoC, first one used for eMMC, second one used for SD card and third one is not used by u-boot.
Signed-off-by Manivannan Sadhasivam <[email protected]>Reviewed-by Simon Glass <[email protected]>Reviewed-by Tom Rini <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190115/6bc31700/attachment.sig>
PATCH v2 1/3 include: configs: Add gunzip size for HiKey board
In reply to Manivannan SadhasivamQuoted 6 lines · Manivannan Sadhasivam
From: Manivannan Sadhasivam <[email protected]>
Default 8MB gunzip size is not enough to load the release kernel, hence fix 64MB size for uncompressing the kernel.
Quoted 8 lines
Signed-off-by Manivannan Sadhasivam <[email protected]>Reviewed-by Simon Glass <[email protected]>---
Changes in v2: Added Simon's Reviewed-by tag.
include/configs/hikey.h | 2 ++ 1 file changed, 2 insertions(+)
PATCH v2 1/3 include: configs: Add gunzip size for HiKey board
In reply to Manivannan SadhasivamQuoted 8 lines · Manivannan Sadhasivam
From: Manivannan Sadhasivam <[email protected]>
Default 8MB gunzip size is not enough to load the release kernel, hence fix 64MB size for uncompressing the kernel.
Signed-off-by Manivannan Sadhasivam <[email protected]>Reviewed-by Simon Glass <[email protected]>Reviewed-by Simon Glass <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190115/a4d80651/attachment.sig>