sunxi: add spi flash bootcmd
PATCH 1/1 sunxi: add spi flash bootcmd
Enable SPI bootcmd if CONFIG_DM_SPI_FLASH is defined.
--- include/configs/sunxi-common.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)
include/configs/sunxi-common.h +16 -0
@@ -401,6 +401,21 @@ extern int soft_i2c_gpio_scl;#define BOOT_TARGET_DEVICES_USB (func)#endif +#ifdef CONFIG_DM_SPI_FLASH +#define BOOT_TARGET_DEVICES_SPI (func) func(SPI, spi, 0) +#define BOOTENV_DEV_SPI (devtypeu, devtypel, instance) \ + "image_addr=0x100000\0" \ + "image_size=0x700000\0" \ + "bootcmd_" #devtypel #instance "=" \ + "if sf probe " #instance "; then " \ + "sf read ${ramdisk_addr_r} ${image_addr} ${image_size}; " \ + "bootm ${ramdisk_addr_r}; " \ + "fi\0" +#define BOOTENV_DEV_NAME_SPI (devtypeu, devtypel, instance) \ + #devtypel #instance " " +#else +#define BOOT_TARGET_DEVICES_SPI (func) +#endif /* FEL boot support, auto-execute boot.scr if a script address was provided */ #define BOOTENV_DEV_FEL (devtypeu, devtypel, instance) \ "bootcmd_fel=" \
@@ -416,6 +431,7 @@ extern int soft_i2c_gpio_scl; BOOT_TARGET_DEVICES_MMC(func) \ BOOT_TARGET_DEVICES_SCSI(func) \ BOOT_TARGET_DEVICES_USB(func) \ + BOOT_TARGET_DEVICES_SPI(func) \ func(PXE, pxe, na) \ func(DHCP, dhcp, na)
Signature · 1 line
2.17.1
PATCH 1/1 sunxi: add spi flash bootcmd
Quoted 12 lines · Oskari Lemmela
Enable SPI bootcmd if
CONFIG_DM_SPI_FLASHis defined.Signed-off-by Oskari Lemmela <[email protected]>--- include/configs/sunxi-common.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)include/configs/sunxi-common.h +0
-0
include/configs/sunxi-common.h extern int soft_i2c_gpio_scl; · line 406
Quoted 6 lines
include/configs/sunxi-common.h +3
-0@@ -401,6 +401,21 @@ extern int soft_i2c_gpio_scl;#define BOOT_TARGET_DEVICES_USB (func)#endif +#ifdef CONFIG_DM_SPI_FLASH +#define BOOT_TARGET_DEVICES_SPI (func) func(SPI, spi, 0) +#define BOOTENV_DEV_SPI (devtypeu, devtypel, instance) \
This belongs more in include/config_distro_bootcmd.h, there's nothing really sunxi specific here.
include/configs/sunxi-common.h extern int soft_i2c_gpio_scl; · line 408
Quoted 2 lines
include/configs/sunxi-common.h +2
-0+"image_addr=0x100000\0" \ +"image_size=0x700000\0" \
image_addr and image_size usually come from Kconfig, instead of being hardcoded
include/configs/sunxi-common.h extern int soft_i2c_gpio_scl; · line 411
Quoted 3 lines
include/configs/sunxi-common.h +3
-0+ "bootcmd_" #devtypel #instance "=" \ + "if sf probe " #instance "; then " \ + "sf read ${ramdisk_addr_r} ${image_addr} ${image_size}; " \
s/ramdisk_addr_r/kernel_addr_r/
Thanks!
Maxime
Signature · 10 lines
Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 228 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190107/11d45255/attachment.sig>
PATCH 1/1 sunxi: add spi flash bootcmd
Quoted 23 lines · On Mon, 7 Jan 2019 14:16:23 +0100 Maxime Ripard <[email protected]>…
Quoted 12 lines · Oskari Lemmela
Enable SPI bootcmd if
CONFIG_DM_SPI_FLASHis defined.Signed-off-by Oskari Lemmela <[email protected]>--- include/configs/sunxi-common.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)(quoted diff) +0
-0
b/include/configs/sunxi-common.hindex9819d9980c..b2443ef678100644include/configs/sunxi-common.h extern int soft_i2c_gpio_scl; · line 406
Quoted 6 lines
include/configs/sunxi-common.h +3
-0@@ -401,6 +401,21 @@ extern int soft_i2c_gpio_scl;#define BOOT_TARGET_DEVICES_USB (func)#endif +#ifdef CONFIG_DM_SPI_FLASH +#define BOOT_TARGET_DEVICES_SPI (func) func(SPI, spi, 0) +#define BOOTENV_DEV_SPI (devtypeu, devtypel, instance) \This belongs more in
include/config_distro_bootcmd.h, there's nothing really sunxi specific here.
Quoted 5 lines
include/configs/sunxi-common.h extern int soft_i2c_gpio_scl; · line 408
Quoted 2 lines
include/configs/sunxi-common.h +2
-0+"image_addr=0x100000\0" \ + "image_size=0x700000\0" \
image_addrandimage_sizeusually come fromKconfig, instead of being hardcoded
Actually this whole approach looks very specific to me, if I understand this correctly, it loads 7 MB from 1MB of the SPI flash and treats this as a kernel?
This looks very arbitrary to me, requires at least 8MB of SPI flash (many boards come with just 2MB) and will never hold any normal arm64 kernel (which are in the range of 16MB, typically).
So this might fit some specific embedded project, but doesn't look like something we want in the default environment. If there is a use case for it, people can always either set up their specific environment (and store it in FAT), or change the default environment just for their build.
Cheers,
Andre.
Quoted 11 lines
include/configs/sunxi-common.h extern int soft_i2c_gpio_scl;
Quoted 5 lines
include/configs/sunxi-common.h +3
-0+ "bootcmd_" #devtypel #instance "=" \ + "if sf probe " #instance "; then " \ + "sf read ${ramdisk_addr_r} ${image_addr} ${image_size}; " \s/ramdisk_addr_r/kernel_addr_r/
Thanks!
Maxime
PATCH 1/1 sunxi: add spi flash bootcmd
Quoted 19 lines · Andre Przywara
Quoted 16 lines · On Mon, 7 Jan 2019 14:16:23 +0100 Maxime Ripard <[email protected]>…
Quoted 15 lines · Oskari Lemmela
Enable SPI bootcmd if
CONFIG_DM_SPI_FLASHis defined.Signed-off-by Oskari Lemmela <[email protected]>--- include/configs/sunxi-common.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)(quoted diff) +0
-0
b/include/configs/sunxi-common.hindex9819d9980c..b2443ef678100644include/configs/sunxi-common.h +0
-0@@ -401,6 +401,21 @@ extern int soft_i2c_gpio_scl;#define BOOT_TARGET_DEVICES_USB (func)#endif
Quoted 5 lines
Quoted 5 lines
include/configs/sunxi-common.h extern int soft_i2c_gpio_scl; · line 406
Quoted 3 lines
include/configs/sunxi-common.h +3
-0+#ifdef CONFIG_DM_SPI_FLASH +#define BOOT_TARGET_DEVICES_SPI (func) func(SPI, spi, 0) +#define BOOTENV_DEV_SPI (devtypeu, devtypel, instance) \This belongs more in
include/config_distro_bootcmd.h, there's nothing really sunxi specific here.
True. I'll try to rework it that way.
Quoted 16 lines
Quoted 4 lines
include/configs/sunxi-common.h extern int soft_i2c_gpio_scl; · line 408
Quoted 2 lines
include/configs/sunxi-common.h +2
-0+"image_addr=0x100000\0" \ + "image_size=0x700000\0" \
image_addrandimage_sizeusually come fromKconfig, instead of being hardcodedActually this whole approach looks very specific to me, if I understand this correctly, it loads 7 MB from 1MB of the SPI flash and treats this as a kernel?
This looks very arbitrary to me, requires at least 8MB of SPI flash (many boards come with just 2MB) and will never hold any normal arm64 kernel (which are in the range of 16MB, typically).
So this might fit some specific embedded project, but doesn't look like something we want in the default environment. If there is a use case for it, people can always either set up their specific environment (and store it in FAT), or change the default environment just for their build.
Quoted 2 lines
Cheers,
Andre.
Making image_addr and image_size configurable via Kconfig would allow this be
generic approach.
Goal is not load kernel image directly as it would be too big for most of SPI
flash devices. Approach is load FIT image some where else and then let u-boot
uncompress and boot it.
Most likely 2MB flash device is not enough even when lzma compressing kernel.
Quoted 5 lines
Quoted 5 lines
include/configs/sunxi-common.h extern int soft_i2c_gpio_scl;
Quoted 4 lines
include/configs/sunxi-common.h +3
-0+ "bootcmd_" #devtypel #instance "=" \ + "if sf probe " #instance "; then " \ + "sf read ${ramdisk_addr_r} ${image_addr} ${image_size}; " \s/ramdisk_addr_r/kernel_addr_r/
Reason explained earlier boot process would be loading FIT image to ramdisk_addr_r. Then u-boot will decompress kernel, dtb and ramdisk to memory
and boot kernel.
Or could it be better not to use ramdisk_addr_r and replace it with some other configurable memory address?
Example boot log:
=> sf probe 0
SF: Detected w25q128bv with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> sf read ${ramdisk_addr_r} ${image_addr} ${image_size} device 0 offset 0x100000, size 0x700000
SF: 7340032 bytes @ 0x100000 Read: OK
=> bootm ${ramdisk_addr_r}
## Loading kernel from FIT Image at 4fe00000 ...
Using 'config at 1' configuration
Trying 'kernel at 1' kernel subimage
Description: ARM64 Linux-4.19.13
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x4fe000e8
Data Size: 2812412 Bytes = 2.7 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x40080000
Entry Point: 0x40080000
Hash algo: crc32
Hash value: 27f9179d
Hash algo: sha1
Hash value: f5e9b16f6958cca20013f06074ad85141ccd3cc6 Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 4fe00000 ...
Using 'config at 1' configuration
Trying 'fdt at 1' fdt subimage
Description: ARM64 sun50i-a64-pine64-lts device tree blob Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x500aec2c
Data Size: 13158 Bytes = 12.8 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 3d2574b7
Hash algo: sha1
Hash value: c55ea000ca7925a505a5de69425b49d8092ceb5e Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x500aec2c
EHCI failed to shut down host controller.
EHCI failed to shut down host controller.
Uncompressing Kernel Image ... OK
Loading Device Tree to 0000000049ff9000, end 0000000049fff365 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
Quoted 4 lines
Quoted 4 lines
Thanks!
Maxime
Thanks!
Oskari
PATCH 1/1 sunxi: add spi flash bootcmd
Quoted 20 lines · On Mon, 7 Jan 2019 19:47:26 +0200 Oskari Lemmelä <[email protected]> wrote:
Quoted 19 lines · Andre Przywara
Quoted 16 lines · On Mon, 7 Jan 2019 14:16:23 +0100 Maxime Ripard <[email protected]>…
Quoted 15 lines · Oskari Lemmela
Enable SPI bootcmd if
CONFIG_DM_SPI_FLASHis defined.Signed-off-by Oskari Lemmela <[email protected]>--- include/configs/sunxi-common.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)(quoted diff) +0
-0
b/include/configs/sunxi-common.hindex9819d9980c..b2443ef678100644 ---a/include/configs/sunxi-common.h
+++b/include/configs/sunxi-common.hinclude/configs/sunxi-common.h +0
-0@@ -401,6 +401,21 @@ extern int soft_i2c_gpio_scl;#define BOOT_TARGET_DEVICES_USB (func)#endif
Quoted 6 lines
Quoted 5 lines
Quoted 5 lines
include/configs/sunxi-common.h extern int soft_i2c_gpio_scl; · line 406
Quoted 3 lines
include/configs/sunxi-common.h +3
-0+#ifdef CONFIG_DM_SPI_FLASH +#define BOOT_TARGET_DEVICES_SPI (func) func(SPI, spi, 0) +#define BOOTENV_DEV_SPI (devtypeu, devtypel, instance) \This belongs more in
include/config_distro_bootcmd.h, there's nothing really sunxi specific here.True. I'll try to rework it that way.
I don't think it belongs there. As the name says, this is for distros to find their kernel, using all kind of standards: boot partitions, magic filenames, config files, etc.
Loading from some made up address from SPI flash doesn't belong there.
Quoted 16 lines
Quoted 16 lines
Quoted 4 lines
include/configs/sunxi-common.h extern int soft_i2c_gpio_scl; · line 408
Quoted 2 lines
include/configs/sunxi-common.h +2
-0+"image_addr=0x100000\0" \ + "image_size=0x700000\0" \
image_addrandimage_sizeusually come fromKconfig, instead of being hardcodedActually this whole approach looks very specific to me, if I understand this correctly, it loads 7 MB from 1MB of the SPI flash and treats this as a kernel?
This looks very arbitrary to me, requires at least 8MB of SPI flash (many boards come with just 2MB) and will never hold any normal arm64 kernel (which are in the range of 16MB, typically). So this might fit some specific embedded project, but doesn't look like something we want in the default environment. If there is a use case for it, people can always either set up their specific environment (and store it in FAT), or change the default environment just for their build.
Quoted 4 lines
Quoted 2 lines
Cheers,
Andre.Making
image_addrandimage_sizeconfigurable viaKconfigwould allow this be generic approach.
It would still not be generic, but I am fine with this if the whole thing is protected by Kconfig: So it only probes SPI flash if there was a flash load address specified at compile time. And by default there should be none, as I still consider this a special use case. In an ideal world the SPI flash would be owned by firmware, so we could put EFI applications (EFI shell, grub) on there, for instance.
Can you also add some documentation on this feature somewhere?
Quoted 14 lines
Goal is not load kernel image directly as it would be too big for most of SPI
flash devices. Approach is load FIT image some where else and then let u-boot
uncompress and boot it.Most likely 2MB flash device is not enough even when lzma compressing kernel.
Quoted 5 lines
Quoted 5 lines
include/configs/sunxi-common.h extern int soft_i2c_gpio_scl;
Quoted 4 lines
include/configs/sunxi-common.h +3
-0+ "bootcmd_" #devtypel #instance "=" \ + "if sf probe " #instance "; then " \ + "sf read ${ramdisk_addr_r} ${image_addr} ${image_size}; " \s/ramdisk_addr_r/kernel_addr_r/
Quoted 7 lines
Reason explained earlier boot process would be loading FIT image to
ramdisk_addr_r. Then u-boot will decompress kernel, dtb and ramdisk to memory
and boot kernel.Or could it be better not to use
ramdisk_addr_rand replace it with some other configurable memory address?
I guess you need to, otherwise extracting the ramdisk would overwrite the image, wouldn't it?
Does bootm detect the ramdisk in a FIT image and does the right thing automatically?
Cheers,
Andre.
Quoted 57 lines
Example boot log:
=> sf probe 0
SF: Detected w25q128bv with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> sf read ${ramdisk_addr_r} ${image_addr} ${image_size} device 0 offset0x100000, size0x700000
SF: 7340032 bytes @0x100000Read: OK
=> bootm ${ramdisk_addr_r}
## Loading kernel from FIT Image at4fe00000...
Using 'config at 1' configuration
Trying 'kernel at 1' kernel subimage
Description: ARM64 Linux-4.19.13
Type: Kernel Image
Compression: lzma compressed
Data Start:0x4fe000e8
Data Size: 2812412 Bytes = 2.7 MiB
Architecture: AArch64
OS: Linux
Load Address:0x40080000
Entry Point:0x40080000
Hash algo: crc32
Hash value:27f9179d
Hash algo: sha1
Hash value:f5e9b16f6958cca20013f06074ad85141ccd3cc6Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at4fe00000...
Using 'config at 1' configuration
Trying 'fdt at 1' fdt subimage
Description: ARM64 sun50i-a64-pine64-lts device tree blob Type: Flat Device Tree
Compression: uncompressed
Data Start:0x500aec2c
Data Size: 13158 Bytes = 12.8 KiB
Architecture: AArch64
Hash algo: crc32
Hash value:3d2574b7
Hash algo: sha1
Hash value:c55ea000ca7925a505a5de69425b49d8092ceb5eVerifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at0x500aec2c
EHCI failed to shut down host controller.
EHCI failed to shut down host controller.
Uncompressing Kernel Image ... OK
Loading Device Tree to0000000049ff9000, end0000000049fff365... OKStarting kernel ...
[ 0.000000] Booting Linux on physical CPU
0x0Quoted 4 lines
Quoted 4 lines
Thanks!
MaximeThanks!
Oskari