ARM: dts: meson8b: odroidc1: Enable usb phy node
PATCH 1/2 ARM: dts: meson8b: odroidc1: Enable usb phy node
Add missing vbus-supply link to phy controller for usb_phy0 and usb_phy1 nodes, this changes fixed the power issue on usb ports usb, changes help fix usb reset warning.
[ 821.991470] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 825.243385] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 828.151310] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 830.991241] usb 1-1.2: reset high-speed USB device number 3 using dwc2
---
Rebased on Kevin's amlogic/v5.0/fixes branch
[alarm@archl-c1t ~]$ lsusb -t
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
|__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M
|__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M
|__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M
|__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M
|__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480M[alarm@archl-c1t ~]$
[alarm@archl-c1t ~]$ lsusb -v|egrep "^Bus|MaxPower"
Couldn't open device, some information will be missing
Bus 001 Device 003: ID 1b71:0056 Fushicai
MaxPower 500mA
Couldn't open device, some information will be missing
Bus 001 Device 004: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
MaxPower 30mA
Couldn't open device, some information will be missing
Couldn't open device, some information will be missing
Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
MaxPower 100mA
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
MaxPower 0mA
--- arch/arm/boot/dts/meson8b-odroidc1.dts | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)
arch/arm/boot/dts/meson8b-odroidc1.dts +23 -0
@@ -83,6 +83,19 @@ regulator-max-microvolt = <5000000>; }; + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&p5v0>; + + gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + tflash_vdd: regulator-tflash_vdd { /* * signal name from schematics: TFLASH_VDD_EN
@@ -293,8 +306,18 @@ pinctrl-names = "default"; }; +&usb0_phy { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + &usb1_phy { status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb0 { + status = "okay"; }; &usb1 {
Signature · 1 line
2.20.1
PATCH 2/2 ARM: dts: meson8b: odroidc1: Fix usb phy regulator power failed warning
Override the dr_mode from "host" to "peripheral" for dwc2 usb_phy0->usb0 initialization of OTG Micro-B type. Changes fix the below warning for phy poweron failed --> -22
This fix the initialization of c9040000.usb phy.
[ 1.639706] phy phy-c1108800.phy.0: USB ID detect failed! [ 1.643850] phy phy-c1108800.phy.0: phy poweron failed --> -22 [ 1.649706] ------------[ cut here ]------------ [ 1.654273] WARNING: CPU: 0 PID: 29 at drivers/regulator/core.c:2054 _regulator_put.part.8+0xf8/0xfc [ 1.663400] Modules linked in: [ 1.666439] CPU: 0 PID: 29 Comm: kworker/0:1 Not tainted 4.20.0-xc1ml #11 [ 1.673192] Hardware name: Amlogic Meson platform [ 1.677894] Workqueue: events deferred_probe_work_func [ 1.683027] [<c0312204>] (unwind_backtrace) from [<c030cb8c>] (show_stack+0x10/0x14) [ 1.690746] [<c030cb8c>] (show_stack) from [<c0e223b8>] (dump_stack+0x8c/0xa0) [ 1.697953] [<c0e223b8>] (dump_stack) from [<c0346334>] (__warn.part.3+0xbc/0xd8) [ 1.705418] [<c0346334>] (__warn.part.3) from [<c03464b0>] (warn_slowpath_null+0x44/0x4c) [ 1.713579] [<c03464b0>] (warn_slowpath_null) from [<c07df6b8>] (_regulator_put.part.8+0xf8/0xfc) [ 1.722437] [<c07df6b8>] (_regulator_put.part.8) from [<c07df6e4>] (regulator_put+0x28/0x38) [ 1.730859] [<c07df6e4>] (regulator_put) from [<c07df71c>] (regulator_bulk_free+0x28/0x38) [ 1.739112] [<c07df71c>] (regulator_bulk_free) from [<c0943858>] (release_nodes+0x1bc/0x200) [ 1.747537] [<c0943858>] (release_nodes) from [<c093f82c>] (really_probe+0x110/0x2cc) [ 1.755350] [<c093f82c>] (really_probe) from [<c093fb4c>] (driver_probe_device+0x60/0x16c) [ 1.763599] [<c093fb4c>] (driver_probe_device) from [<c093dcd4>] (bus_for_each_drv+0x80/0xc4) [ 1.772110] [<c093dcd4>] (bus_for_each_drv) from [<c093f6ac>] (__device_attach+0xd0/0x138) [ 1.780359] [<c093f6ac>] (__device_attach) from [<c093eae4>] (bus_probe_device+0x84/0x8c) [ 1.788522] [<c093eae4>] (bus_probe_device) from [<c093ef80>] (deferred_probe_work_func+0x60/0x8c) [ 1.797470] [<c093ef80>] (deferred_probe_work_func) from [<c035fdb8>] (process_one_work+0x218/0x504) [ 1.806585] [<c035fdb8>] (process_one_work) from [<c0360ea8>] (worker_thread+0x2a8/0x5bc) [ 1.814748] [<c0360ea8>] (worker_thread) from [<c0365a18>] (kthread+0x14c/0x154) [ 1.822128] [<c0365a18>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 1.829331] Exception stack(0xee0ebfb0 to 0xee0ebff8) [ 1.834369] bfa0: 00000000 00000000 00000000 00000000 [ 1.842534] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.850695] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 1.857311] ---[ end trace e28bbc26874282a4 ]--- [ 1.861984] ------------[ cut here ]------------ [ 1.866524] WARNING: CPU: 0 PID: 29 at drivers/regulator/core.c:2054 _regulator_put.part.8+0xf8/0xfc [ 1.875629] Modules linked in: [ 1.878658] CPU: 0 PID: 29 Comm: kworker/0:1 Tainted: GW 4.20.0-xc1ml #11 [ 1.886817] Hardware name: Amlogic Meson platform [ 1.891513] Workqueue: events deferred_probe_work_func [ 1.896641] [<c0312204>] (unwind_backtrace) from [<c030cb8c>] (show_stack+0x10/0x14) [ 1.904366] [<c030cb8c>] (show_stack) from [<c0e223b8>] (dump_stack+0x8c/0xa0) [ 1.911573] [<c0e223b8>] (dump_stack) from [<c0346334>] (__warn.part.3+0xbc/0xd8) [ 1.919041] [<c0346334>] (__warn.part.3) from [<c03464b0>] (warn_slowpath_null+0x44/0x4c) [ 1.927203] [<c03464b0>] (warn_slowpath_null) from [<c07df6b8>] (_regulator_put.part.8+0xf8/0xfc) [ 1.936060] [<c07df6b8>] (_regulator_put.part.8) from [<c07df6e4>] (regulator_put+0x28/0x38) [ 1.944483] [<c07df6e4>] (regulator_put) from [<c07df71c>] (regulator_bulk_free+0x28/0x38) [ 1.952734] [<c07df71c>] (regulator_bulk_free) from [<c0943858>] (release_nodes+0x1bc/0x200) [ 1.961159] [<c0943858>] (release_nodes) from [<c093f82c>] (really_probe+0x110/0x2cc) [ 1.968974] [<c093f82c>] (really_probe) from [<c093fb4c>] (driver_probe_device+0x60/0x16c) [ 1.977224] [<c093fb4c>] (driver_probe_device) from [<c093dcd4>] (bus_for_each_drv+0x80/0xc4) [ 1.985734] [<c093dcd4>] (bus_for_each_drv) from [<c093f6ac>] (__device_attach+0xd0/0x138) [ 1.993984] [<c093f6ac>] (__device_attach) from [<c093eae4>] (bus_probe_device+0x84/0x8c) [ 2.002147] [<c093eae4>] (bus_probe_device) from [<c093ef80>] (deferred_probe_work_func+0x60/0x8c) [ 2.011092] [<c093ef80>] (deferred_probe_work_func) from [<c035fdb8>] (process_one_work+0x218/0x504) [ 2.020209] [<c035fdb8>] (process_one_work) from [<c0360ea8>] (worker_thread+0x2a8/0x5bc) [ 2.028371] [<c0360ea8>] (worker_thread) from [<c0365a18>] (kthread+0x14c/0x154) [ 2.035752] [<c0365a18>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 2.042955] Exception stack(0xee0ebfb0 to 0xee0ebff8) [ 2.047993] bfa0: 00000000 00000000 00000000 00000000 [ 2.056158] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 2.064320] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 2.070934] ---[ end trace e28bbc26874282a5 ]---
---
Rebased on Kevin's amlogic/v5.0/fixes branch
Note the warning is not getting produced on the latest kernel.
--- arch/arm/boot/dts/meson8b-odroidc1.dts | 1 + 1 file changed, 1 insertion(+)
arch/arm/boot/dts/meson8b-odroidc1.dts +1 -0
@@ -318,6 +318,7 @@ &usb0 { status = "okay"; + dr_mode = "peripheral"; }; &usb1 {
Signature · 1 line
2.20.1
Martin Blumenstingl
reviewerRe: [PATCH 2/2] ARM: dts: meson8b: odroidc1: Fix usb phy regulator power failed warning
Hi Anand,
Quoted 84 lines · Anand Moon
Override the
dr_modefrom "host" to "peripheral" for dwc2usb_phy0->usb0initialization of OTG Micro-B type. Changes fix the below warning for phy poweron failed --> -22This fix the initialization of c9040000.usb phy.
[ 1.639706] phy phy-c1108800.phy.0: USB ID detect failed! [ 1.643850] phy phy-c1108800.phy.0: phy poweron failed --> -22 [ 1.649706] ------------[ cut here ]------------ [ 1.654273] WARNING: CPU: 0 PID: 29 at drivers/regulator/core.c:2054 _regulator_put.part.8+0xf8/0xfc [ 1.663400] Modules linked in: [ 1.666439] CPU: 0 PID: 29 Comm: kworker/0:1 Not tainted 4.20.0-xc1ml #11 [ 1.673192] Hardware name: Amlogic Meson platform [ 1.677894] Workqueue: events deferred_probe_work_func [ 1.683027] [<c0312204>] (unwind_backtrace) from [<c030cb8c>] (show_stack+0x10/0x14) [ 1.690746] [<c030cb8c>] (show_stack) from [<c0e223b8>] (dump_stack+0x8c/0xa0) [ 1.697953] [<c0e223b8>] (dump_stack) from [<c0346334>] (__warn.part.3+0xbc/0xd8) [ 1.705418] [<c0346334>] (__warn.part.3) from [<c03464b0>] (warn_slowpath_null+0x44/0x4c) [ 1.713579] [<c03464b0>] (warn_slowpath_null) from [<c07df6b8>] (_regulator_put.part.8+0xf8/0xfc) [ 1.722437] [<c07df6b8>] (_regulator_put.part.8) from [<c07df6e4>] (regulator_put+0x28/0x38) [ 1.730859] [<c07df6e4>] (regulator_put) from [<c07df71c>] (regulator_bulk_free+0x28/0x38) [ 1.739112] [<c07df71c>] (regulator_bulk_free) from [<c0943858>] (release_nodes+0x1bc/0x200) [ 1.747537] [<c0943858>] (release_nodes) from [<c093f82c>] (really_probe+0x110/0x2cc) [ 1.755350] [<c093f82c>] (really_probe) from [<c093fb4c>] (driver_probe_device+0x60/0x16c) [ 1.763599] [<c093fb4c>] (driver_probe_device) from [<c093dcd4>] (bus_for_each_drv+0x80/0xc4) [ 1.772110] [<c093dcd4>] (bus_for_each_drv) from [<c093f6ac>] (__device_attach+0xd0/0x138) [ 1.780359] [<c093f6ac>] (__device_attach) from [<c093eae4>] (bus_probe_device+0x84/0x8c) [ 1.788522] [<c093eae4>] (bus_probe_device) from [<c093ef80>] (deferred_probe_work_func+0x60/0x8c) [ 1.797470] [<c093ef80>] (deferred_probe_work_func) from [<c035fdb8>] (process_one_work+0x218/0x504) [ 1.806585] [<c035fdb8>] (process_one_work) from [<c0360ea8>] (worker_thread+0x2a8/0x5bc) [ 1.814748] [<c0360ea8>] (worker_thread) from [<c0365a18>] (kthread+0x14c/0x154) [ 1.822128] [<c0365a18>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 1.829331] Exception stack(0xee0ebfb0 to 0xee0ebff8) [ 1.834369] bfa0: 00000000 00000000 00000000 00000000 [ 1.842534] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.850695] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 1.857311] ---[ end trace e28bbc26874282a4 ]--- [ 1.861984] ------------[ cut here ]------------ [ 1.866524] WARNING: CPU: 0 PID: 29 at drivers/regulator/core.c:2054 _regulator_put.part.8+0xf8/0xfc [ 1.875629] Modules linked in: [ 1.878658] CPU: 0 PID: 29 Comm: kworker/0:1 Tainted: GW 4.20.0-xc1ml #11 [ 1.886817] Hardware name: Amlogic Meson platform [ 1.891513] Workqueue: events deferred_probe_work_func [ 1.896641] [<c0312204>] (unwind_backtrace) from [<c030cb8c>] (show_stack+0x10/0x14) [ 1.904366] [<c030cb8c>] (show_stack) from [<c0e223b8>] (dump_stack+0x8c/0xa0) [ 1.911573] [<c0e223b8>] (dump_stack) from [<c0346334>] (__warn.part.3+0xbc/0xd8) [ 1.919041] [<c0346334>] (__warn.part.3) from [<c03464b0>] (warn_slowpath_null+0x44/0x4c) [ 1.927203] [<c03464b0>] (warn_slowpath_null) from [<c07df6b8>] (_regulator_put.part.8+0xf8/0xfc) [ 1.936060] [<c07df6b8>] (_regulator_put.part.8) from [<c07df6e4>] (regulator_put+0x28/0x38) [ 1.944483] [<c07df6e4>] (regulator_put) from [<c07df71c>] (regulator_bulk_free+0x28/0x38) [ 1.952734] [<c07df71c>] (regulator_bulk_free) from [<c0943858>] (release_nodes+0x1bc/0x200) [ 1.961159] [<c0943858>] (release_nodes) from [<c093f82c>] (really_probe+0x110/0x2cc) [ 1.968974] [<c093f82c>] (really_probe) from [<c093fb4c>] (driver_probe_device+0x60/0x16c) [ 1.977224] [<c093fb4c>] (driver_probe_device) from [<c093dcd4>] (bus_for_each_drv+0x80/0xc4) [ 1.985734] [<c093dcd4>] (bus_for_each_drv) from [<c093f6ac>] (__device_attach+0xd0/0x138) [ 1.993984] [<c093f6ac>] (__device_attach) from [<c093eae4>] (bus_probe_device+0x84/0x8c) [ 2.002147] [<c093eae4>] (bus_probe_device) from [<c093ef80>] (deferred_probe_work_func+0x60/0x8c) [ 2.011092] [<c093ef80>] (deferred_probe_work_func) from [<c035fdb8>] (process_one_work+0x218/0x504) [ 2.020209] [<c035fdb8>] (process_one_work) from [<c0360ea8>] (worker_thread+0x2a8/0x5bc) [ 2.028371] [<c0360ea8>] (worker_thread) from [<c0365a18>] (kthread+0x14c/0x154) [ 2.035752] [<c0365a18>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 2.042955] Exception stack(0xee0ebfb0 to 0xee0ebff8) [ 2.047993] bfa0: 00000000 00000000 00000000 00000000 [ 2.056158] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 2.064320] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 2.070934] ---[ end trace e28bbc26874282a5 ]---Cc Martin Blumenstingl <[email protected]>Cc Jerome Brunet <[email protected]>Cc Neil Armstrong <[email protected]>Signed-off-by Anand Moon <[email protected]>---
Rebased on Kevin's amlogic/v5.0/fixes branch
Note the warning is not getting produced on the latest kernel.--- arch/arm/boot/dts/meson8b-odroidc1.dts | 1 + 1 file changed, 1 insertion(+)arch/arm/boot/dts/meson8b-odroidc1.dts +0
-0
arch/arm/boot/dts/meson8b-odroidc1.dts line 322
Quoted 5 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +1
-0@@ -318,6 +318,7 @@ &usb0 { status = "okay"; + dr_mode = "peripheral"; };
with this change I get the following message during boot:
dwc2 c9040000.usb: Configuration mismatch. dr_mode forced to host
as far as I understand your original problem is the following error from the USB2 PHY driver:
phy phy-c1108800.phy.0: USB ID detect failed!
phy phy-c1108800.phy.0: phy poweron failed --> -22
maybe we should fix that instead?
Regards
Martin
Re: [PATCH 2/2] ARM: dts: meson8b: odroidc1: Fix usb phy regulator power failed warning
Hi Martin,
Quoted 96 lines · Martin Blumenstingl
Hi Anand,
Quoted 84 lines · Anand Moon
Override the
dr_modefrom "host" to "peripheral" for dwc2usb_phy0->usb0initialization of OTG Micro-B type. Changes fix the below warning for phy poweron failed --> -22This fix the initialization of c9040000.usb phy.
[ 1.639706] phy phy-c1108800.phy.0: USB ID detect failed! [ 1.643850] phy phy-c1108800.phy.0: phy poweron failed --> -22 [ 1.649706] ------------[ cut here ]------------ [ 1.654273] WARNING: CPU: 0 PID: 29 at drivers/regulator/core.c:2054 _regulator_put.part.8+0xf8/0xfc [ 1.663400] Modules linked in: [ 1.666439] CPU: 0 PID: 29 Comm: kworker/0:1 Not tainted 4.20.0-xc1ml #11 [ 1.673192] Hardware name: Amlogic Meson platform [ 1.677894] Workqueue: events deferred_probe_work_func [ 1.683027] [<c0312204>] (unwind_backtrace) from [<c030cb8c>] (show_stack+0x10/0x14) [ 1.690746] [<c030cb8c>] (show_stack) from [<c0e223b8>] (dump_stack+0x8c/0xa0) [ 1.697953] [<c0e223b8>] (dump_stack) from [<c0346334>] (__warn.part.3+0xbc/0xd8) [ 1.705418] [<c0346334>] (__warn.part.3) from [<c03464b0>] (warn_slowpath_null+0x44/0x4c) [ 1.713579] [<c03464b0>] (warn_slowpath_null) from [<c07df6b8>] (_regulator_put.part.8+0xf8/0xfc) [ 1.722437] [<c07df6b8>] (_regulator_put.part.8) from [<c07df6e4>] (regulator_put+0x28/0x38) [ 1.730859] [<c07df6e4>] (regulator_put) from [<c07df71c>] (regulator_bulk_free+0x28/0x38) [ 1.739112] [<c07df71c>] (regulator_bulk_free) from [<c0943858>] (release_nodes+0x1bc/0x200) [ 1.747537] [<c0943858>] (release_nodes) from [<c093f82c>] (really_probe+0x110/0x2cc) [ 1.755350] [<c093f82c>] (really_probe) from [<c093fb4c>] (driver_probe_device+0x60/0x16c) [ 1.763599] [<c093fb4c>] (driver_probe_device) from [<c093dcd4>] (bus_for_each_drv+0x80/0xc4) [ 1.772110] [<c093dcd4>] (bus_for_each_drv) from [<c093f6ac>] (__device_attach+0xd0/0x138) [ 1.780359] [<c093f6ac>] (__device_attach) from [<c093eae4>] (bus_probe_device+0x84/0x8c) [ 1.788522] [<c093eae4>] (bus_probe_device) from [<c093ef80>] (deferred_probe_work_func+0x60/0x8c) [ 1.797470] [<c093ef80>] (deferred_probe_work_func) from [<c035fdb8>] (process_one_work+0x218/0x504) [ 1.806585] [<c035fdb8>] (process_one_work) from [<c0360ea8>] (worker_thread+0x2a8/0x5bc) [ 1.814748] [<c0360ea8>] (worker_thread) from [<c0365a18>] (kthread+0x14c/0x154) [ 1.822128] [<c0365a18>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 1.829331] Exception stack(0xee0ebfb0 to 0xee0ebff8) [ 1.834369] bfa0: 00000000 00000000 00000000 00000000 [ 1.842534] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.850695] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 1.857311] ---[ end trace e28bbc26874282a4 ]--- [ 1.861984] ------------[ cut here ]------------ [ 1.866524] WARNING: CPU: 0 PID: 29 at drivers/regulator/core.c:2054 _regulator_put.part.8+0xf8/0xfc [ 1.875629] Modules linked in: [ 1.878658] CPU: 0 PID: 29 Comm: kworker/0:1 Tainted: GW 4.20.0-xc1ml #11 [ 1.886817] Hardware name: Amlogic Meson platform [ 1.891513] Workqueue: events deferred_probe_work_func [ 1.896641] [<c0312204>] (unwind_backtrace) from [<c030cb8c>] (show_stack+0x10/0x14) [ 1.904366] [<c030cb8c>] (show_stack) from [<c0e223b8>] (dump_stack+0x8c/0xa0) [ 1.911573] [<c0e223b8>] (dump_stack) from [<c0346334>] (__warn.part.3+0xbc/0xd8) [ 1.919041] [<c0346334>] (__warn.part.3) from [<c03464b0>] (warn_slowpath_null+0x44/0x4c) [ 1.927203] [<c03464b0>] (warn_slowpath_null) from [<c07df6b8>] (_regulator_put.part.8+0xf8/0xfc) [ 1.936060] [<c07df6b8>] (_regulator_put.part.8) from [<c07df6e4>] (regulator_put+0x28/0x38) [ 1.944483] [<c07df6e4>] (regulator_put) from [<c07df71c>] (regulator_bulk_free+0x28/0x38) [ 1.952734] [<c07df71c>] (regulator_bulk_free) from [<c0943858>] (release_nodes+0x1bc/0x200) [ 1.961159] [<c0943858>] (release_nodes) from [<c093f82c>] (really_probe+0x110/0x2cc) [ 1.968974] [<c093f82c>] (really_probe) from [<c093fb4c>] (driver_probe_device+0x60/0x16c) [ 1.977224] [<c093fb4c>] (driver_probe_device) from [<c093dcd4>] (bus_for_each_drv+0x80/0xc4) [ 1.985734] [<c093dcd4>] (bus_for_each_drv) from [<c093f6ac>] (__device_attach+0xd0/0x138) [ 1.993984] [<c093f6ac>] (__device_attach) from [<c093eae4>] (bus_probe_device+0x84/0x8c) [ 2.002147] [<c093eae4>] (bus_probe_device) from [<c093ef80>] (deferred_probe_work_func+0x60/0x8c) [ 2.011092] [<c093ef80>] (deferred_probe_work_func) from [<c035fdb8>] (process_one_work+0x218/0x504) [ 2.020209] [<c035fdb8>] (process_one_work) from [<c0360ea8>] (worker_thread+0x2a8/0x5bc) [ 2.028371] [<c0360ea8>] (worker_thread) from [<c0365a18>] (kthread+0x14c/0x154) [ 2.035752] [<c0365a18>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 2.042955] Exception stack(0xee0ebfb0 to 0xee0ebff8) [ 2.047993] bfa0: 00000000 00000000 00000000 00000000 [ 2.056158] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 2.064320] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 2.070934] ---[ end trace e28bbc26874282a5 ]---Cc Martin Blumenstingl <[email protected]>Cc Jerome Brunet <[email protected]>Cc Neil Armstrong <[email protected]>Signed-off-by Anand Moon <[email protected]>---
Rebased on Kevin's amlogic/v5.0/fixes branch
Note the warning is not getting produced on the latest kernel.--- arch/arm/boot/dts/meson8b-odroidc1.dts | 1 + 1 file changed, 1 insertion(+)arch/arm/boot/dts/meson8b-odroidc1.dts +0
-0arch/arm/boot/dts/meson8b-odroidc1.dts line 322
Quoted 5 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +1
-0@@ -318,6 +318,7 @@ &usb0 { status = "okay"; + dr_mode = "peripheral"; };with this change I get the following message during boot:
dwc2 c9040000.usb: Configuration mismatch.dr_modeforced to host
Quoted 5 lines
as far as I understand your original problem is the following error from the USB2 PHY driver:
phy phy-c1108800.phy.0: USB ID detect failed!
phy phy-c1108800.phy.0: phy poweron failed --> -22
maybe we should fix that instead?
I could not fix the phy reg setting for c1108800 setting in dts to look into.
Quoted 4 lines
Regards
Martin
Thanks for pointing my mistake.
Actually the dr_mode = "otg"; seem to be correct solution. with this changes we need to fix the phy-meson8b-usb2.c to enable the OTG bus port.
Best Regards
-Anand
Re: [PATCH 2/2] ARM: dts: meson8b: odroidc1: Fix usb phy regulator power failed warning
In reply to Martin BlumenstinglHi Martin,
Quoted 103 lines · Martin Blumenstingl
Hi Anand,
Quoted 84 lines · Anand Moon
Override the
dr_modefrom "host" to "peripheral" for dwc2usb_phy0->usb0initialization of OTG Micro-B type. Changes fix the below warning for phy poweron failed --> -22This fix the initialization of c9040000.usb phy.
[ 1.639706] phy phy-c1108800.phy.0: USB ID detect failed! [ 1.643850] phy phy-c1108800.phy.0: phy poweron failed --> -22 [ 1.649706] ------------[ cut here ]------------ [ 1.654273] WARNING: CPU: 0 PID: 29 at drivers/regulator/core.c:2054 _regulator_put.part.8+0xf8/0xfc [ 1.663400] Modules linked in: [ 1.666439] CPU: 0 PID: 29 Comm: kworker/0:1 Not tainted 4.20.0-xc1ml #11 [ 1.673192] Hardware name: Amlogic Meson platform [ 1.677894] Workqueue: events deferred_probe_work_func [ 1.683027] [<c0312204>] (unwind_backtrace) from [<c030cb8c>] (show_stack+0x10/0x14) [ 1.690746] [<c030cb8c>] (show_stack) from [<c0e223b8>] (dump_stack+0x8c/0xa0) [ 1.697953] [<c0e223b8>] (dump_stack) from [<c0346334>] (__warn.part.3+0xbc/0xd8) [ 1.705418] [<c0346334>] (__warn.part.3) from [<c03464b0>] (warn_slowpath_null+0x44/0x4c) [ 1.713579] [<c03464b0>] (warn_slowpath_null) from [<c07df6b8>] (_regulator_put.part.8+0xf8/0xfc) [ 1.722437] [<c07df6b8>] (_regulator_put.part.8) from [<c07df6e4>] (regulator_put+0x28/0x38) [ 1.730859] [<c07df6e4>] (regulator_put) from [<c07df71c>] (regulator_bulk_free+0x28/0x38) [ 1.739112] [<c07df71c>] (regulator_bulk_free) from [<c0943858>] (release_nodes+0x1bc/0x200) [ 1.747537] [<c0943858>] (release_nodes) from [<c093f82c>] (really_probe+0x110/0x2cc) [ 1.755350] [<c093f82c>] (really_probe) from [<c093fb4c>] (driver_probe_device+0x60/0x16c) [ 1.763599] [<c093fb4c>] (driver_probe_device) from [<c093dcd4>] (bus_for_each_drv+0x80/0xc4) [ 1.772110] [<c093dcd4>] (bus_for_each_drv) from [<c093f6ac>] (__device_attach+0xd0/0x138) [ 1.780359] [<c093f6ac>] (__device_attach) from [<c093eae4>] (bus_probe_device+0x84/0x8c) [ 1.788522] [<c093eae4>] (bus_probe_device) from [<c093ef80>] (deferred_probe_work_func+0x60/0x8c) [ 1.797470] [<c093ef80>] (deferred_probe_work_func) from [<c035fdb8>] (process_one_work+0x218/0x504) [ 1.806585] [<c035fdb8>] (process_one_work) from [<c0360ea8>] (worker_thread+0x2a8/0x5bc) [ 1.814748] [<c0360ea8>] (worker_thread) from [<c0365a18>] (kthread+0x14c/0x154) [ 1.822128] [<c0365a18>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 1.829331] Exception stack(0xee0ebfb0 to 0xee0ebff8) [ 1.834369] bfa0: 00000000 00000000 00000000 00000000 [ 1.842534] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.850695] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 1.857311] ---[ end trace e28bbc26874282a4 ]--- [ 1.861984] ------------[ cut here ]------------ [ 1.866524] WARNING: CPU: 0 PID: 29 at drivers/regulator/core.c:2054 _regulator_put.part.8+0xf8/0xfc [ 1.875629] Modules linked in: [ 1.878658] CPU: 0 PID: 29 Comm: kworker/0:1 Tainted: GW 4.20.0-xc1ml #11 [ 1.886817] Hardware name: Amlogic Meson platform [ 1.891513] Workqueue: events deferred_probe_work_func [ 1.896641] [<c0312204>] (unwind_backtrace) from [<c030cb8c>] (show_stack+0x10/0x14) [ 1.904366] [<c030cb8c>] (show_stack) from [<c0e223b8>] (dump_stack+0x8c/0xa0) [ 1.911573] [<c0e223b8>] (dump_stack) from [<c0346334>] (__warn.part.3+0xbc/0xd8) [ 1.919041] [<c0346334>] (__warn.part.3) from [<c03464b0>] (warn_slowpath_null+0x44/0x4c) [ 1.927203] [<c03464b0>] (warn_slowpath_null) from [<c07df6b8>] (_regulator_put.part.8+0xf8/0xfc) [ 1.936060] [<c07df6b8>] (_regulator_put.part.8) from [<c07df6e4>] (regulator_put+0x28/0x38) [ 1.944483] [<c07df6e4>] (regulator_put) from [<c07df71c>] (regulator_bulk_free+0x28/0x38) [ 1.952734] [<c07df71c>] (regulator_bulk_free) from [<c0943858>] (release_nodes+0x1bc/0x200) [ 1.961159] [<c0943858>] (release_nodes) from [<c093f82c>] (really_probe+0x110/0x2cc) [ 1.968974] [<c093f82c>] (really_probe) from [<c093fb4c>] (driver_probe_device+0x60/0x16c) [ 1.977224] [<c093fb4c>] (driver_probe_device) from [<c093dcd4>] (bus_for_each_drv+0x80/0xc4) [ 1.985734] [<c093dcd4>] (bus_for_each_drv) from [<c093f6ac>] (__device_attach+0xd0/0x138) [ 1.993984] [<c093f6ac>] (__device_attach) from [<c093eae4>] (bus_probe_device+0x84/0x8c) [ 2.002147] [<c093eae4>] (bus_probe_device) from [<c093ef80>] (deferred_probe_work_func+0x60/0x8c) [ 2.011092] [<c093ef80>] (deferred_probe_work_func) from [<c035fdb8>] (process_one_work+0x218/0x504) [ 2.020209] [<c035fdb8>] (process_one_work) from [<c0360ea8>] (worker_thread+0x2a8/0x5bc) [ 2.028371] [<c0360ea8>] (worker_thread) from [<c0365a18>] (kthread+0x14c/0x154) [ 2.035752] [<c0365a18>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) [ 2.042955] Exception stack(0xee0ebfb0 to 0xee0ebff8) [ 2.047993] bfa0: 00000000 00000000 00000000 00000000 [ 2.056158] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 2.064320] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 2.070934] ---[ end trace e28bbc26874282a5 ]---Cc Martin Blumenstingl <[email protected]>Cc Jerome Brunet <[email protected]>Cc Neil Armstrong <[email protected]>Signed-off-by Anand Moon <[email protected]>---
Rebased on Kevin's amlogic/v5.0/fixes branch
Note the warning is not getting produced on the latest kernel.--- arch/arm/boot/dts/meson8b-odroidc1.dts | 1 + 1 file changed, 1 insertion(+)arch/arm/boot/dts/meson8b-odroidc1.dts +0
-0arch/arm/boot/dts/meson8b-odroidc1.dts line 322
Quoted 5 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +1
-0@@ -318,6 +318,7 @@ &usb0 { status = "okay"; + dr_mode = "peripheral"; };with this change I get the following message during boot:
dwc2 c9040000.usb: Configuration mismatch.dr_modeforced to hostas far as I understand your original problem is the following error from the USB2 PHY driver:
phy phy-c1108800.phy.0: USB ID detect failed!
phy phy-c1108800.phy.0: phy poweron failed --> -22
maybe we should fix that instead?
Quoted 2 lines
Regards
Martin
I have tried to fix this bug using dts + phy changes. Please find the details below.
# cat /sys/kernel/debug/regulator/regulator_summary
regulator use open bypass opmode voltage
current min max
---------------------------------------------------------------------------------------
regulator-dummy 6 5 0 unknown 0mV
0mA 0mV 0mV
c90c0000.usb 1
0mA 0mV 0mV
c90c0000.usb 1
0mA 0mV 0mV
c9040000.usb 1
0mA 0mV 0mV
c9040000.usb 1
0mA 0mV 0mV
VCCK 1 1 0 unknown 860mV
0mA 860mV 1140mV
cpu0 0
0mA 860mV 860mV
P5V0 3 4 0 unknown 5000mV
0mA 5000mV 5000mV
VCC1V8 1 1 0 unknown 1800mV
0mA 1800mV 1800mV
c1108680.adc 1
0mA 0mV 0mV
VCC3V3 1 2 0 unknown 3300mV
0mA 3300mV 3300mV
VDD_RTC 0 0 0 unknown 900mV
0mA 900mV 900mV
TFLASH_VDD 1 1 0 unknown 3300mV
0mA 3300mV 3300mV
c1108c20.mmc:slot@1 1
0mA 3300mV 3400mV
DDR_VDDC 0 0 0 unknown 1500mV
0mA 1500mV 1500mV
USB_VBUS 2 1 0 unknown 5000mV
0mA 5000mV 5000mV
phy-c1108800.phy.0 2
0mA 0mV 0mV
TF_IO 0 1 0 unknown 3300mV
0mA 1800mV 3300mV
c1108c20.mmc:slot@1 0
0mA 0mV 0mV# lsusb -t
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
|__ Port 1: Dev 6, If 0, Class=Mass Storage, Driver=usb-storage, 480M
|__ Port 2: Dev 3, If 0, Class=Mass Storage, Driver=usb-storage, 480M
|__ Port 3: Dev 4, If 1, Class=Video, Driver=uvcvideo, 480M
|__ Port 3: Dev 4, If 2, Class=Audio, Driver=snd-usb-audio, 480M
|__ Port 3: Dev 4, If 0, Class=Video, Driver=uvcvideo, 480M
|__ Port 3: Dev 4, If 3, Class=Audio, Driver=snd-usb-audio, 480M
|__ Port 4: Dev 5, If 0, Class=Mass Storage, Driver=usb-storage, 480M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480MNow I am trying to fix initialization of the Bus 01.Port (usb0) otg port fix.
Best Regards
-Anand
Martin Blumenstingl
reviewerHi Anand,
thank you for this patch!
Quoted 4 lines · Anand Moon
Add missing vbus-supply link to phy controller for
usb_phy0andusb_phy1nodes, this changes fixed the power issue on usb ports usb, changes help fix usb reset warning.
I trust you on the fact that GPIOAO_5 controls VBUS of USB0 and USB1
to me the schematics are not 100% clear or I'm bad at interpreting them:
- I'll refer to odroid-c1+_rev0.4_20150615.pdf
- page 1 lists GPIOAO.BIT5 as input for the PWREN signal of the USB_OTG controller (usb0)
- page 1 also shows a PWREN signal in the USB_HOST controller (usb1) but not it's input
- based on your patch I assume that PWREN is the same signal for both USB controllers
Quoted 6 lines
[ 821.991470] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 825.243385] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 828.151310] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 830.991241] usb 1-1.2: reset high-speed USB device number 3 using dwc2Fixes 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host controller on Odroid-C1/C1+ board)
you already split your original patch into two, however I suggest splitting these patches differently:
- this one (personally I would choose "ARM: dts: meson8b: odroidc1:
fix USB VBUS supplies" as title), which contains the Fixes tag, adds the "usb_vbus" and references it in the "usb0" and "usb1" nodes
- enables usb0_phy and usb0 as part of your second patch (I would call that "ARM: dts: meson8b: odroidc1: enable the OTG capable USB controller")
Quoted 38 lines
Cc Martin Blumenstingl <[email protected]>Cc Jerome Brunet <[email protected]>Cc Neil Armstrong <[email protected]>Signed-off-by Anand Moon <[email protected]>---
Rebased on Kevin's amlogic/v5.0/fixes branch[alarm@archl-c1t ~]$ lsusb -t
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M |__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M |__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M |__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480M[alarm@archl-c1t ~]$
[alarm@archl-c1t ~]$ lsusb -v|egrep "^Bus|MaxPower"
Couldn't open device, some information will be missing
Bus 001 Device 003: ID 1b71:0056 Fushicai
MaxPower 500mA
Couldn't open device, some information will be missing
Bus 001 Device 004: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
MaxPower 30mA
Couldn't open device, some information will be missing
Couldn't open device, some information will be missing
Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
MaxPower 100mA
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
MaxPower 0mA--- arch/arm/boot/dts/meson8b-odroidc1.dts | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)arch/arm/boot/dts/meson8b-odroidc1.dts +0
-0
arch/arm/boot/dts/meson8b-odroidc1.dts line 86
Quoted 4 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +1
-0@@ -83,6 +83,19 @@ regulator-max-microvolt = <5000000>; }; + usb_vbus: regulator-usb-vbus {
please add a comment here with some details about the regulator and add a hint that the signal in the schematics is called "PWREN"
Quoted 22 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +15
-0+ compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&p5v0>; + + gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + tflash_vdd: regulator-tflash_vdd { /* * signal name from schematics: TFLASH_VDD_EN@@ -293,8 +306,18 @@ pinctrl-names = "default"; }; +&usb0_phy { + status = "okay"; + vbus-supply = <&usb_vbus>;
arch/arm/boot/dts/meson8b-odroidc1.dts line 321
Quoted 10 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +7
-0+}; + &usb1_phy { status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb0 { + status = "okay"; };
I believe there's a problem with the usb/usb_phy nodes here. on my Odroid-C1 this results in:
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 0 0 0 unknown 5000mV 0mA 5000mV 5000mV (open count is 0)
if I move "vbus-supply" to the "usb1" node (just as an example) then I get:
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 1 1 0 unknown 5000mV 0mA 5000mV 5000mV
unfortunately neither your original patch nor the modified version seem to enable USB VBUS on my Odroid-C1.
I have documented my findings already back in December, see "USB issues on Odroid-C1" [0]
help on that would be highly appreciated :)
on which board revision have you tested this patch?
Regards
Martin
[0] http://lists.infradead.org/pipermail/linux-amlogic/2018-December/009451.html
Hi Martin,
Thanks for your review comments.
Quoted 12 lines · Martin Blumenstingl
Hi Anand,
thank you for this patch!
Quoted 4 lines · Anand Moon
Add missing vbus-supply link to phy controller for
usb_phy0andusb_phy1nodes, this changes fixed the power issue on usb ports usb, changes help fix usb reset warning.I trust you on the fact that
GPIOAO_5controls VBUS of USB0 and USB1
Quoted 9 lines
to me the schematics are not 100% clear or I'm bad at interpreting them:
- I'll refer to odroid-c1+_rev0.4_20150615.pdf
- page 1 lists GPIOAO.BIT5 as input for the PWREN signal of theUSB_OTGcontroller (usb0)
- page 1 also shows a PWREN signal in theUSB_HOSTcontroller (usb1) but not it's input
- based on your patch I assume that PWREN is the same signal for both USB controllers
As per the schematics odroid-c1+_rev0.4_20150615.pdf
It seem that their vbus setting for *OTG* port. *Bus 01.Port 1* using *GPIOAO.BIT5* gpio
But we also need set power supply for *USB_B* port. *Bus 02.Port 1* ? I don't know but I will try to find solution.
We need to enable some bit in phy driver ?
Quoted 6 lines
Quoted 6 lines
[ 821.991470] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 825.243385] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 828.151310] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 830.991241] usb 1-1.2: reset high-speed USB device number 3 using dwc2Fixes 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host controller on Odroid-C1/C1+ board)
Quoted 8 lines
you already split your original patch into two, however I suggest splitting these patches differently:
- this one (personally I would choose "ARM: dts: meson8b: odroidc1:
fix USB VBUS supplies" as title), which contains the Fixes tag, adds the "usb_vbus" and references it in the "usb0" and "usb1" nodes
- enablesusb0_phyand usb0 as part of your second patch (I would call that "ARM: dts: meson8b: odroidc1: enable the OTG capable USB controller")
Ok I will fix this as per you suggestion in the next version.
Quoted 42 lines
Quoted 42 lines
Cc Martin Blumenstingl <[email protected]>Cc Jerome Brunet <[email protected]>Cc Neil Armstrong <[email protected]>Signed-off-by Anand Moon <[email protected]>---
Rebased on Kevin's amlogic/v5.0/fixes branch[alarm@archl-c1t ~]$ lsusb -t
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M |__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M |__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M |__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480M[alarm@archl-c1t ~]$
[alarm@archl-c1t ~]$ lsusb -v|egrep "^Bus|MaxPower"
Couldn't open device, some information will be missing
Bus 001 Device 003: ID 1b71:0056 Fushicai
MaxPower 500mA
Couldn't open device, some information will be missing
Bus 001 Device 004: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
MaxPower 30mA
Couldn't open device, some information will be missing
Couldn't open device, some information will be missing
Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
MaxPower 100mA
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
MaxPower 0mA--- arch/arm/boot/dts/meson8b-odroidc1.dts | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)arch/arm/boot/dts/meson8b-odroidc1.dts +0
-0@@ -83,6 +83,19 @@ regulator-max-microvolt = <5000000>; };
Quoted 3 lines
arch/arm/boot/dts/meson8b-odroidc1.dts line 86
Quoted 1 line
arch/arm/boot/dts/meson8b-odroidc1.dts +1
-0+ usb_vbus: regulator-usb-vbus {please add a comment here with some details about the regulator and add a hint that the signal in the schematics is called "PWREN"
Ok I will add this comment in the next patch.
Quoted 40 lines
Quoted 23 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +15
-0+ compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&p5v0>; + + gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + tflash_vdd: regulator-tflash_vdd { /* * signal name from schematics: TFLASH_VDD_EN@@ -293,8 +306,18 @@ pinctrl-names = "default"; }; +&usb0_phy { + status = "okay"; + vbus-supply = <&usb_vbus>;arch/arm/boot/dts/meson8b-odroidc1.dts line 321
Quoted 10 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +7
-0+}; + &usb1_phy { status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb0 { + status = "okay"; };I believe there's a problem with the usb/usb_phy nodes here. on my Odroid-C1 this results in:
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 0 0 0 unknown 5000mV 0mA 5000mV 5000mV (open count is 0)
Quoted 4 lines
if I move "vbus-supply" to the "usb1" node (just as an example) then I get:
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 1 1 0 unknown 5000mV 0mA 5000mV 5000mV
Sorry for the mixing the vbus-supply node.
After fix the phy driver code and dts changes I am getting this changes.
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS
USB_VBUS 1 2 0 unknown 5000mV
0mA 5000mV 5000mVNow I am able to enable both *Bus 01.Port 1* and *Bus 02.Port 1*
# lsusb -t
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
|__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M
|__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M
|__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M
|__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M
|__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480MBut not usb device are getting enable on *Bus 01.Port 1*
Quoted 9 lines
unfortunately neither your original patch nor the modified version seem to enable USB VBUS on my Odroid-C1.
I have documented my findings already back in December, see "USB issues on Odroid-C1" [0]
help on that would be highly appreciated :)on which board revision have you tested this patch?
I have with me for testing
ODROID-C0 REV 0.4 20151217
ODROID-C1+ REV 0.4 20150615 ----> current testing on ODROID-C1+ REV 0.4 20160226
Quoted 6 lines
Regards
Martin[0] http://lists.infradead.org/pipermail/linux-amlogic/2018-December/009451.html
Best Regards
-Anand
Martin Blumenstingl
reviewerHi Anand,
Quoted 28 lines · Anand Moon
Hi Martin,
Thanks for your review comments.
Quoted 12 lines · Martin Blumenstingl
Hi Anand,
thank you for this patch!
Quoted 4 lines · Anand Moon
Add missing vbus-supply link to phy controller for
usb_phy0andusb_phy1nodes, this changes fixed the power issue on usb ports usb, changes help fix usb reset warning.I trust you on the fact that
GPIOAO_5controls VBUS of USB0 and USB1Quoted 9 lines
to me the schematics are not 100% clear or I'm bad at interpreting them:
- I'll refer to odroid-c1+_rev0.4_20150615.pdf
- page 1 lists GPIOAO.BIT5 as input for the PWREN signal of theUSB_OTGcontroller (usb0)
- page 1 also shows a PWREN signal in theUSB_HOSTcontroller (usb1) but not it's input
- based on your patch I assume that PWREN is the same signal for both USB controllers
Quoted 4 lines
As per the schematics odroid-c1+_rev0.4_20150615.pdf
It seem that their vbus setting for *OTG* port. *Bus 01.Port 1* using *GPIOAO.BIT5* gpio
that matches my interpretation of the schematics
Quoted 2 lines
But we also need set power supply for *USB_B* port. *Bus 02.Port 1* ? I don't know but I will try to find solution.
I assume we also have to enable VBUS for the host only port, but I don't know how
Quoted 1 line
We need to enable some bit in phy driver ?
I'm not aware of any bit in the PHY driver which can toggle VBUS
(trying to be creative here) maybe the GPIO is incorrectly configured to pull up or down?
if you want me to compare anything: there's some Armbian image (where the USB host ports are working fine) on the eMMC of my Odroid-C1 so I can get you the values you're looking for
Quoted 117 lines
Quoted 6 lines
Quoted 6 lines
[ 821.991470] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 825.243385] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 828.151310] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 830.991241] usb 1-1.2: reset high-speed USB device number 3 using dwc2Fixes 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host controller on Odroid-C1/C1+ board)Quoted 8 lines
you already split your original patch into two, however I suggest splitting these patches differently:
- this one (personally I would choose "ARM: dts: meson8b: odroidc1:
fix USB VBUS supplies" as title), which contains the Fixes tag, adds the "usb_vbus" and references it in the "usb0" and "usb1" nodes
- enablesusb0_phyand usb0 as part of your second patch (I would call that "ARM: dts: meson8b: odroidc1: enable the OTG capable USB controller")Ok I will fix this as per you suggestion in the next version.
Quoted 42 lines
Quoted 42 lines
Cc Martin Blumenstingl <[email protected]>Cc Jerome Brunet <[email protected]>Cc Neil Armstrong <[email protected]>Signed-off-by Anand Moon <[email protected]>---
Rebased on Kevin's amlogic/v5.0/fixes branch[alarm@archl-c1t ~]$ lsusb -t
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M |__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M |__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M |__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480M[alarm@archl-c1t ~]$
[alarm@archl-c1t ~]$ lsusb -v|egrep "^Bus|MaxPower"
Couldn't open device, some information will be missing
Bus 001 Device 003: ID 1b71:0056 Fushicai
MaxPower 500mA
Couldn't open device, some information will be missing
Bus 001 Device 004: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
MaxPower 30mA
Couldn't open device, some information will be missing
Couldn't open device, some information will be missing
Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
MaxPower 100mA
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
MaxPower 0mA--- arch/arm/boot/dts/meson8b-odroidc1.dts | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)arch/arm/boot/dts/meson8b-odroidc1.dts +0
-0@@ -83,6 +83,19 @@ regulator-max-microvolt = <5000000>; };Quoted 3 lines
arch/arm/boot/dts/meson8b-odroidc1.dts line 86
Quoted 1 line
arch/arm/boot/dts/meson8b-odroidc1.dts +1
-0+ usb_vbus: regulator-usb-vbus {please add a comment here with some details about the regulator and add a hint that the signal in the schematics is called "PWREN"
Ok I will add this comment in the next patch.
Quoted 40 lines
Quoted 23 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +15
-0+ compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&p5v0>; + + gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + tflash_vdd: regulator-tflash_vdd { /* * signal name from schematics: TFLASH_VDD_EN@@ -293,8 +306,18 @@ pinctrl-names = "default"; }; +&usb0_phy { + status = "okay"; + vbus-supply = <&usb_vbus>;arch/arm/boot/dts/meson8b-odroidc1.dts line 321
Quoted 10 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +7
-0+}; + &usb1_phy { status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb0 { + status = "okay"; };I believe there's a problem with the usb/usb_phy nodes here. on my Odroid-C1 this results in:
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 0 0 0 unknown 5000mV 0mA 5000mV 5000mV (open count is 0)Quoted 4 lines
if I move "vbus-supply" to the "usb1" node (just as an example) then I get:
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 1 1 0 unknown 5000mV 0mA 5000mV 5000mVSorry for the mixing the vbus-supply node.
After fix the phy driver code and dts changes I am getting this changes.
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 1 2 0 unknown 5000mV 0mA 5000mV 5000mVNow I am able to enable both *Bus 01.Port 1* and *Bus 02.Port 1*
Quoted 8 lines
# lsusb -t
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
|__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M
|__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M
|__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M
|__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M
|__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480Mso this is the host-only controller (usb1) and it's working fine for you - very nice!
Quoted 3 lines
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
But not usb device are getting enable on *Bus 01.Port 1*
so you have something plugged into the OTG capable controller (usb0) using an OTG cable?
I've not tried this before on my Odroid-C1 because I'm using the micro USB connector to power the board
do you get VBUS (maybe you have a USB thumb drive with an LED which lights up when you connect it)?
do you get any errors or warnings from the dwc2 driver during boot?
Quoted 7 lines
Quoted 7 lines
unfortunately neither your original patch nor the modified version seem to enable USB VBUS on my Odroid-C1.
I have documented my findings already back in December, see "USB issues on Odroid-C1" [0]
help on that would be highly appreciated :)
Quoted 7 lines
Quoted 2 lines
on which board revision have you tested this patch?
I have with me for testing
ODROID-C0 REV 0.4 20151217
ODROID-C1+ REV 0.4 20150615 ----> current testing on
I have the exact same Odroid-C1+ board revision
this is my u-boot version:
U-boot-00000-gb7b8dc2-dirty(odroidc@b7b8dc21) (Sep 01 2017 - 01:18:22) -> b7b8dc21 is the lastest commit of the hardkernel odroidc-v2011.03 u-boot branch at the time of writing
Regards
Martin
Hi Martin,
Thanks for you comments.
Quoted 32 lines · Martin Blumenstingl
Hi Anand,
Quoted 28 lines · Anand Moon
Hi Martin,
Thanks for your review comments.
Quoted 21 lines · Martin Blumenstingl
Hi Anand,
thank you for this patch!
Quoted 4 lines · Anand Moon
Add missing vbus-supply link to phy controller for
usb_phy0andusb_phy1nodes, this changes fixed the power issue on usb ports usb, changes help fix usb reset warning.I trust you on the fact that
GPIOAO_5controls VBUS of USB0 and USB1to me the schematics are not 100% clear or I'm bad at interpreting them:
- I'll refer to odroid-c1+_rev0.4_20150615.pdf
- page 1 lists GPIOAO.BIT5 as input for the PWREN signal of theUSB_OTGcontroller (usb0)
- page 1 also shows a PWREN signal in theUSB_HOSTcontroller (usb1) but not it's input
- based on your patch I assume that PWREN is the same signal for both USB controllers
Quoted 5 lines
Quoted 4 lines
As per the schematics odroid-c1+_rev0.4_20150615.pdf
It seem that their vbus setting for *OTG* port. *Bus 01.Port 1* using *GPIOAO.BIT5* gpio
that matches my interpretation of the schematics
Yep, I feel that GPIOAO.BIT5 enable the PWREN power on Bus 02.Port (usb1) But I could not get this to enable on Bus 01.Port (usb0).
usb hot-plug of devices is working fine on *usb1* but not on *usb0*. I have tried different combination but it's not working for me.
I am attaching small changes to phy which enables the Bus 01.Port (usb0) on Odroid C1+/Odroidc2.
we need to set dr_mode="otg" to enable this bus in dts.
Quoted 11 lines
Quoted 3 lines
But we also need set power supply for *USB_B* port. *Bus 02.Port 1* ? I don't know but I will try to find solution.
I assume we also have to enable VBUS for the host only port, but I don't know how
Quoted 1 line
We need to enable some bit in phy driver ?
I'm not aware of any bit in the PHY driver which can toggle VBUS
(trying to be creative here) maybe the GPIO is incorrectly configured to pull up or down?
I have tried this but no luck.
Quoted 129 lines
if you want me to compare anything: there's some Armbian image (where the USB host ports are working fine) on the eMMC of my Odroid-C1 so I can get you the values you're looking for
Quoted 117 lines
Quoted 6 lines
Quoted 6 lines
[ 821.991470] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 825.243385] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 828.151310] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 830.991241] usb 1-1.2: reset high-speed USB device number 3 using dwc2Fixes 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host controller on Odroid-C1/C1+ board)Quoted 8 lines
you already split your original patch into two, however I suggest splitting these patches differently:
- this one (personally I would choose "ARM: dts: meson8b: odroidc1:
fix USB VBUS supplies" as title), which contains the Fixes tag, adds the "usb_vbus" and references it in the "usb0" and "usb1" nodes
- enablesusb0_phyand usb0 as part of your second patch (I would call that "ARM: dts: meson8b: odroidc1: enable the OTG capable USB controller")Ok I will fix this as per you suggestion in the next version.
Quoted 42 lines
Quoted 42 lines
Cc Martin Blumenstingl <[email protected]>Cc Jerome Brunet <[email protected]>Cc Neil Armstrong <[email protected]>Signed-off-by Anand Moon <[email protected]>---
Rebased on Kevin's amlogic/v5.0/fixes branch[alarm@archl-c1t ~]$ lsusb -t
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M |__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M |__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M |__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480M[alarm@archl-c1t ~]$
[alarm@archl-c1t ~]$ lsusb -v|egrep "^Bus|MaxPower"
Couldn't open device, some information will be missing
Bus 001 Device 003: ID 1b71:0056 Fushicai
MaxPower 500mA
Couldn't open device, some information will be missing
Bus 001 Device 004: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
MaxPower 30mA
Couldn't open device, some information will be missing
Couldn't open device, some information will be missing
Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
MaxPower 100mA
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
MaxPower 0mA--- arch/arm/boot/dts/meson8b-odroidc1.dts | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)arch/arm/boot/dts/meson8b-odroidc1.dts +0
-0@@ -83,6 +83,19 @@ regulator-max-microvolt = <5000000>; };Quoted 3 lines
arch/arm/boot/dts/meson8b-odroidc1.dts line 86
Quoted 1 line
arch/arm/boot/dts/meson8b-odroidc1.dts +1
-0+ usb_vbus: regulator-usb-vbus {please add a comment here with some details about the regulator and add a hint that the signal in the schematics is called "PWREN"
Ok I will add this comment in the next patch.
Quoted 40 lines
Quoted 23 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +15
-0+ compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&p5v0>; + + gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + tflash_vdd: regulator-tflash_vdd { /* * signal name from schematics: TFLASH_VDD_EN@@ -293,8 +306,18 @@ pinctrl-names = "default"; }; +&usb0_phy { + status = "okay"; + vbus-supply = <&usb_vbus>;arch/arm/boot/dts/meson8b-odroidc1.dts line 321
Quoted 10 lines
arch/arm/boot/dts/meson8b-odroidc1.dts +7
-0+}; + &usb1_phy { status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb0 { + status = "okay"; };I believe there's a problem with the usb/usb_phy nodes here. on my Odroid-C1 this results in:
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 0 0 0 unknown 5000mV 0mA 5000mV 5000mV (open count is 0)Quoted 4 lines
if I move "vbus-supply" to the "usb1" node (just as an example) then I get:
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 1 1 0 unknown 5000mV 0mA 5000mV 5000mVSorry for the mixing the vbus-supply node.
After fix the phy driver code and dts changes I am getting this changes.
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 1 2 0 unknown 5000mV 0mA 5000mV 5000mVNow I am able to enable both *Bus 01.Port 1* and *Bus 02.Port 1*
Quoted 8 lines
# lsusb -t /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M |__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M |__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M |__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480M
Quoted 8 lines
so this is the host-only controller (usb1) and it's working fine for you - very nice!
Quoted 3 lines
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
But not usb device are getting enable on *Bus 01.Port 1*
so you have something plugged into the OTG capable controller (usb0) using an OTG cable?
Yes I have connected USB-OTG cable with storage device attached, led lights on the device is blinking, but no power to the port is enable. so not hotplug of device is working on this port.
Quoted 2 lines
I've not tried this before on my Odroid-C1 because I'm using the micro USB connector to power the board
Correct me if I am wrong, we need to tune USB phy driver to enable as power the board ?
Quoted 5 lines
do you get VBUS (maybe you have a USB thumb drive with an LED which lights up when you connect it)?
do you get any errors or warnings from the dwc2 driver during boot?
Please find the boot log of my Odroid C1+ here
[0]: https://pastebin.com/PiDmVmEC
I dont see any major error on usb side.
Quoted 12 lines
Quoted 12 lines
Quoted 9 lines
unfortunately neither your original patch nor the modified version seem to enable USB VBUS on my Odroid-C1.
I have documented my findings already back in December, see "USB issues on Odroid-C1" [0]
help on that would be highly appreciated :)on which board revision have you tested this patch?
I have with me for testing
Quoted 8 lines
Quoted 2 lines
ODROID-C0 REV 0.4 20151217
ODROID-C1+ REV 0.4 20150615 ----> current testing onI have the exact same Odroid-C1+ board revision
this is my u-boot version:
U-boot-00000-gb7b8dc2-dirty(odroidc@b7b8dc21) (Sep 01 2017 - 01:18:22) ->b7b8dc21is the lastest commit of the hardkernel odroidc-v2011.03 u-boot branch at the time of writing
I am using the the u-boot from archlinux.
If their is another u-boot for Odroid c1 plz let me know, I will try to install this on my system.
Thanks for your input.
Quoted 3 lines
Regards
Martin
drivers/phy/amlogic/phy-meson8b-usb2.c +15 -0
@@ -109,6 +109,7 @@#define RESET_COMPLETE_TIME 500#define ACA_ENABLE_COMPLETE_TIME 50 +#define DCD_ENABLE_COMPLETE_TIME 10struct phy_meson8b_usb2_priv {void __iomem *regs;
@@ -188,6 +189,20 @@ static int phy_meson8b_usb2_power_on(struct phy *phy)udelay (ACA_ENABLE_COMPLETE_TIME ); +if (phy_meson8b_usb2_read (priv,REG_ADP_BC ) & +REG_ADP_BC_ACA_PIN_FLOAT ) { +dev_warn (&phy->dev,"USB ID detect failed!\n" ); +clk_disable_unprepare (priv->clk_usb); +clk_disable_unprepare (priv->clk_usb_general); +return -EINVAL ; + } + }else if (priv->dr_mode ==USB_DR_MODE_OTG ) { +phy_meson8b_usb2_mask_bits (priv,REG_ADP_BC , +REG_ADP_BC_DCD_ENABLE , +REG_ADP_BC_DCD_ENABLE ); + +udelay (DCD_ENABLE_COMPLETE_TIME ); +if (phy_meson8b_usb2_read (priv,REG_ADP_BC ) ®_ADP_BC_ACA_PIN_FLOAT ) {dev_warn (&phy->dev,"USB ID detect failed!\n" );
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Martin Blumenstingl
reviewerHi Anand,
Quoted 48 lines · Anand Moon
Hi Martin,
Thanks for you comments.
Quoted 32 lines · Martin Blumenstingl
Hi Anand,
Quoted 28 lines · Anand Moon
Hi Martin,
Thanks for your review comments.
Quoted 21 lines · Martin Blumenstingl
Hi Anand,
thank you for this patch!
Quoted 4 lines · Anand Moon
Add missing vbus-supply link to phy controller for
usb_phy0andusb_phy1nodes, this changes fixed the power issue on usb ports usb, changes help fix usb reset warning.I trust you on the fact that
GPIOAO_5controls VBUS of USB0 and USB1to me the schematics are not 100% clear or I'm bad at interpreting them:
- I'll refer to odroid-c1+_rev0.4_20150615.pdf
- page 1 lists GPIOAO.BIT5 as input for the PWREN signal of theUSB_OTGcontroller (usb0)
- page 1 also shows a PWREN signal in theUSB_HOSTcontroller (usb1) but not it's input
- based on your patch I assume that PWREN is the same signal for both USB controllersQuoted 5 lines
Quoted 4 lines
As per the schematics odroid-c1+_rev0.4_20150615.pdf
It seem that their vbus setting for *OTG* port. *Bus 01.Port 1* using *GPIOAO.BIT5* gpio
that matches my interpretation of the schematics
Yep, I feel that GPIOAO.BIT5 enable the PWREN power on Bus 02.Port (usb1) But I could not get this to enable on Bus 01.Port (usb0).
Quoted 6 lines
usb hot-plug of devices is working fine on *usb1* but not on *usb0*. I have tried different combination but it's not working for me.
I am attaching small changes to phy which enables the Bus 01.Port (usb0) on Odroid C1+/Odroidc2.
we need to set dr_mode="otg" to enable this bus in dts.
I need to get my multimeter out and measure on my own Odroid-C1 I *believe* to have observed that toggling GPIOAO.BIT5 changes the voltage at at the OTG port, but it's been a few weeks since then... let me know if you want me to do the measurements on my Odroid-C1+ again
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
But we also need set power supply for *USB_B* port. *Bus 02.Port 1* ? I don't know but I will try to find solution.
I assume we also have to enable VBUS for the host only port, but I don't know how
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
We need to enable some bit in phy driver ?
I'm not aware of any bit in the PHY driver which can toggle VBUS
(trying to be creative here) maybe the GPIO is incorrectly configured to pull up or down?
I have tried this but no luck.
OK, too bad
[...]
Quoted 20 lines
Quoted 20 lines
Quoted 7 lines
After fix the phy driver code and dts changes I am getting this changes.
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 1 2 0 unknown 5000mV 0mA 5000mV 5000mVNow I am able to enable both *Bus 01.Port 1* and *Bus 02.Port 1*
Quoted 8 lines
# lsusb -t /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M |__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M |__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M |__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480Mso this is the host-only controller (usb1) and it's working fine for you - very nice!
Quoted 2 lines
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
But not usb device are getting enable on *Bus 01.Port 1*
so you have something plugged into the OTG capable controller (usb0) using an OTG cable?
Yes I have connected USB-OTG cable with storage device attached, led lights on the device is blinking, but no power to the port is enable. so not hotplug of device is working on this port.
thanks for confirming this!
can you please send an updated version of both patches? if you want someone else to test and/or review the patches before they are applied you can use the subject prefix "RFT PATCH n/m" or "RFC PATCH n/m" (RFT means "request for testing", "RFC" means "request for comments")
Quoted 5 lines
Quoted 2 lines
I've not tried this before on my Odroid-C1 because I'm using the micro USB connector to power the board
Correct me if I am wrong, we need to tune USB phy driver to enable as power the board ?
so far I have seen two designs on Amlogic boards:
- VBUS is hardwired to +5V
- VBUS is controlled by a regulator/current limiting switch/etc. which can be toggled using a GPIO
the PHY is involved in this because for the OTG port it senses the ID line to decide whether the controller has to go into host or device (peripheral) mode.
however, this part is not implemented in the mainline phy-meson8b-usb2 driver yet
in case someone is interested in *why* dwc2 doesn't do OTG on the Amlogic SoCs yet - here are the notes from the top of my head:
- the dwc2 controller doesn't get an interrupt when switching between host and peripheral mode
- instead the Amlogic vendor kernel has a timer which polls the PHY registers
- if the timer handler detects a "mode change" in the PHY registers it changes the dwc2 mode
- however, in mainline the PHY can't notify the USB controller driver (dwc2) to change the mode (yet)
Quoted 10 lines
Quoted 5 lines
do you get VBUS (maybe you have a USB thumb drive with an LED which lights up when you connect it)?
do you get any errors or warnings from the dwc2 driver during boot?Please find the boot log of my Odroid C1+ here
[0]: https://pastebin.com/PiDmVmECI dont see any major error on usb side.
that looks very good indeed. as I already mentioned above: please send an updated version of the patches so I can try to reproduce your test results!
Quoted 14 lines
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
on which board revision have you tested this patch?
I have with me for testing
Quoted 8 lines
Quoted 2 lines
ODROID-C0 REV 0.4 20151217
ODROID-C1+ REV 0.4 20150615 ----> current testing onI have the exact same Odroid-C1+ board revision
this is my u-boot version:
U-boot-00000-gb7b8dc2-dirty(odroidc@b7b8dc21) (Sep 01 2017 - 01:18:22) ->b7b8dc21is the lastest commit of the hardkernel odroidc-v2011.03 u-boot branch at the time of writing
Quoted 3 lines
I am using the the u-boot from archlinux.
If their is another u-boot for Odroid c1 plz let me know, I will try to install this on my system.
I don't remember where I got my u-boot version from.
maybe I should switch to the Arch Linux ARM one instead (so I'm back to a well-known state). but let's wait for the test results from your updated patches first.
Regards
Martin
Hi Martin,
Quoted 102 lines · Martin Blumenstingl
Hi Anand,
Quoted 48 lines · Anand Moon
Hi Martin,
Thanks for you comments.
Quoted 32 lines · Martin Blumenstingl
Hi Anand,
Quoted 28 lines · Anand Moon
Hi Martin,
Thanks for your review comments.
Quoted 21 lines · Martin Blumenstingl
Hi Anand,
thank you for this patch!
Quoted 4 lines · Anand Moon
Add missing vbus-supply link to phy controller for
usb_phy0andusb_phy1nodes, this changes fixed the power issue on usb ports usb, changes help fix usb reset warning.I trust you on the fact that
GPIOAO_5controls VBUS of USB0 and USB1to me the schematics are not 100% clear or I'm bad at interpreting them:
- I'll refer to odroid-c1+_rev0.4_20150615.pdf
- page 1 lists GPIOAO.BIT5 as input for the PWREN signal of theUSB_OTGcontroller (usb0)
- page 1 also shows a PWREN signal in theUSB_HOSTcontroller (usb1) but not it's input
- based on your patch I assume that PWREN is the same signal for both USB controllersQuoted 5 lines
Quoted 4 lines
As per the schematics odroid-c1+_rev0.4_20150615.pdf
It seem that their vbus setting for *OTG* port. *Bus 01.Port 1* using *GPIOAO.BIT5* gpio
that matches my interpretation of the schematics
Yep, I feel that GPIOAO.BIT5 enable the PWREN power on Bus 02.Port (usb1) But I could not get this to enable on Bus 01.Port (usb0).
Quoted 6 lines
usb hot-plug of devices is working fine on *usb1* but not on *usb0*. I have tried different combination but it's not working for me.
I am attaching small changes to phy which enables the Bus 01.Port (usb0) on Odroid C1+/Odroidc2.
we need to set dr_mode="otg" to enable this bus in dts.I need to get my multimeter out and measure on my own Odroid-C1 I *believe* to have observed that toggling GPIOAO.BIT5 changes the voltage at at the OTG port, but it's been a few weeks since then... let me know if you want me to do the measurements on my Odroid-C1+ again
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
But we also need set power supply for *USB_B* port. *Bus 02.Port 1* ? I don't know but I will try to find solution.
I assume we also have to enable VBUS for the host only port, but I don't know how
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
We need to enable some bit in phy driver ?
I'm not aware of any bit in the PHY driver which can toggle VBUS
(trying to be creative here) maybe the GPIO is incorrectly configured to pull up or down?
I have tried this but no luck.
OK, too bad
[...]
Quoted 24 lines
Quoted 23 lines
Quoted 7 lines
After fix the phy driver code and dts changes I am getting this changes.
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS USB_VBUS 1 2 0 unknown 5000mV 0mA 5000mV 5000mVNow I am able to enable both *Bus 01.Port 1* and *Bus 02.Port 1*
Quoted 8 lines
# lsusb -t /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M |__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M |__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M |__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480Mso this is the host-only controller (usb1) and it's working fine for you - very nice!
Quoted 3 lines
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
But not usb device are getting enable on *Bus 01.Port 1*
so you have something plugged into the OTG capable controller (usb0) using an OTG cable?
Quoted 9 lines
Quoted 3 lines
Yes I have connected USB-OTG cable with storage device attached, led lights on the device is blinking, but no power to the port is enable. so not hotplug of device is working on this port.
thanks for confirming this!
can you please send an updated version of both patches? if you want someone else to test and/or review the patches before they are applied you can use the subject prefix "RFT PATCH n/m" or "RFC PATCH n/m" (RFT means "request for testing", "RFC" means "request for comments")
I have tried to address the issue in the next series of patches.
Quoted 16 lines
Quoted 5 lines
Quoted 2 lines
I've not tried this before on my Odroid-C1 because I'm using the micro USB connector to power the board
Correct me if I am wrong, we need to tune USB phy driver to enable as power the board ?
so far I have seen two designs on Amlogic boards:
- VBUS is hardwired to +5V
- VBUS is controlled by a regulator/current limiting switch/etc. which can be toggled using a GPIOthe PHY is involved in this because for the OTG port it senses the ID line to decide whether the controller has to go into host or device (peripheral) mode.
however, this part is not implemented in the mainline phy-meson8b-usb2 driver yet
Quoted 10 lines
in case someone is interested in *why* dwc2 doesn't do OTG on the Amlogic SoCs yet - here are the notes from the top of my head:
- the dwc2 controller doesn't get an interrupt when switching between host and peripheral mode
- instead the Amlogic vendor kernel has a timer which polls the PHY registers
- if the timer handler detects a "mode change" in the PHY registers it changes the dwc2 mode
- however, in mainline the PHY can't notify the USB controller driver (dwc2) to change the mode (yet)
Thanks for your input.
Yep I tired to study the code changes in the u-boot from amlogic. I tried to enable few bit in the phy to test enable of usb otg port but no success.
I have tested that otg port is used to power on the board.
Quoted 31 lines
Quoted 10 lines
Quoted 5 lines
do you get VBUS (maybe you have a USB thumb drive with an LED which lights up when you connect it)?
do you get any errors or warnings from the dwc2 driver during boot?Please find the boot log of my Odroid C1+ here
[0]: https://pastebin.com/PiDmVmECI dont see any major error on usb side.
that looks very good indeed. as I already mentioned above: please send an updated version of the patches so I can try to reproduce your test results!
Quoted 14 lines
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
on which board revision have you tested this patch?
I have with me for testing
Quoted 8 lines
Quoted 2 lines
ODROID-C0 REV 0.4 20151217
ODROID-C1+ REV 0.4 20150615 ----> current testing onI have the exact same Odroid-C1+ board revision
this is my u-boot version:
U-boot-00000-gb7b8dc2-dirty(odroidc@b7b8dc21) (Sep 01 2017 - 01:18:22) ->b7b8dc21is the lastest commit of the hardkernel odroidc-v2011.03 u-boot branch at the time of writingQuoted 3 lines
I am using the the u-boot from archlinux.
If their is another u-boot for Odroid c1 plz let me know, I will try to install this on my system.
Quoted 8 lines
I don't remember where I got my u-boot version from.
maybe I should switch to the Arch Linux ARM one instead (so I'm back to a well-known state). but let's wait for the test results from your updated patches first.Regards
Martin
Best Regards
-Anand
Kevin Hilman
maintainerQuoted 9 lines · Anand Moon
Add missing vbus-supply link to phy controller for
usb_phy0andusb_phy1nodes, this changes fixed the power issue on usb ports usb, changes help fix usb reset warning.[ 821.991470] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 825.243385] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 828.151310] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 830.991241] usb 1-1.2: reset high-speed USB device number 3 using dwc2
Quoted 7 lines
Fixes 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host controller on Odroid-C1/C1+ board)Cc Martin Blumenstingl <[email protected]>Cc Jerome Brunet <[email protected]>Cc Neil Armstrong <[email protected]>Signed-off-by Anand Moon <[email protected]>---
Rebased on Kevin's amlogic/v5.0/fixes branch
As requested, dropping this series from the fixes branch pending further debug and testing.
Kevin
Quoted 71 lines
[alarm@archl-c1t ~]$ lsusb -t
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M |__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M |__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M |__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M |__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480M[alarm@archl-c1t ~]$
[alarm@archl-c1t ~]$ lsusb -v|egrep "^Bus|MaxPower"
Couldn't open device, some information will be missing
Bus 001 Device 003: ID 1b71:0056 Fushicai
MaxPower 500mA
Couldn't open device, some information will be missing
Bus 001 Device 004: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
MaxPower 30mA
Couldn't open device, some information will be missing
Couldn't open device, some information will be missing
Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
MaxPower 100mA
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
MaxPower 0mA--- arch/arm/boot/dts/meson8b-odroidc1.dts | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)arch/arm/boot/dts/meson8b-odroidc1.dts +23
-0@@ -83,6 +83,19 @@ regulator-max-microvolt = <5000000>; }; + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&p5v0>; + + gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + tflash_vdd: regulator-tflash_vdd { /* * signal name from schematics: TFLASH_VDD_EN@@ -293,8 +306,18 @@ pinctrl-names = "default"; }; +&usb0_phy { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + &usb1_phy { status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb0 { + status = "okay"; }; &usb1 {Signature · 1 line
2.20.1
Hi Kevin,
Quoted 20 lines · Kevin Hilman
Quoted 9 lines · Anand Moon
Add missing vbus-supply link to phy controller for
usb_phy0andusb_phy1nodes, this changes fixed the power issue on usb ports usb, changes help fix usb reset warning.[ 821.991470] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 825.243385] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 828.151310] usb 1-1.2: reset high-speed USB device number 3 using dwc2 [ 830.991241] usb 1-1.2: reset high-speed USB device number 3 using dwc2Quoted 7 lines
Fixes 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host controller on Odroid-C1/C1+ board)Cc Martin Blumenstingl <[email protected]>Cc Jerome Brunet <[email protected]>Cc Neil Armstrong <[email protected]>Signed-off-by Anand Moon <[email protected]>---
Rebased on Kevin's amlogic/v5.0/fixes branch
Quoted 4 lines
As requested, dropping this series from the fixes branch pending further debug and testing.
Kevin
[snip]
Thanks your very much.
Best Regards
-Anand