Skip to contentSkip to conversation

x86, numa: always initialize all possible nodes

RFC PATCH In review Michal Hocko 6 participants 12 messages Jan 14, 2019 – Feb 11, 2019

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

RFC PATCH 1/1 x86, numa: always initialize all possible nodes

From: Michal Hocko <[email protected]>

Pingfan Liu has reported the following splat

[    5.772742] BUG: unable to handle kernel paging request at 0000000000002088
[    5.773618] PGD 0 P4D 0
[    5.773618] Oops: 0000 [#1] SMP NOPTI
[    5.773618] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.20.0-rc1+ #3
[    5.773618] Hardware name: Dell Inc. PowerEdge R7425/02MJ3T, BIOS 1.4.3 06/29/2018
[    5.773618] RIP: 0010:__alloc_pages_nodemask+0xe2/0x2a0
[    5.773618] Code: 00 00 44 89 ea 80 ca 80 41 83 f8 01 44 0f 44 ea 89 da c1 ea 08 83 e2 01 88 54 24 20 48 8b 54 24 08 48 85 d2 0f 85 46 01 00 00 <3b> 77 08 0f 82 3d 01 00 00 48 89 f8 44 89 ea 48 89
e1 44 89 e6 89
[    5.773618] RSP: 0018:ffffaa600005fb20 EFLAGS: 00010246
[    5.773618] RAX: 0000000000000000 RBX: 00000000006012c0 RCX: 0000000000000000
[    5.773618] RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000002080
[    5.773618] RBP: 00000000006012c0 R08: 0000000000000000 R09: 0000000000000002
[    5.773618] R10: 00000000006080c0 R11: 0000000000000002 R12: 0000000000000000
[    5.773618] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000002
[    5.773618] FS:  0000000000000000(0000) GS:ffff8c69afe00000(0000) knlGS:0000000000000000
[    5.773618] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    5.773618] CR2: 0000000000002088 CR3: 000000087e00a000 CR4: 00000000003406e0
[    5.773618] Call Trace:
[    5.773618]  new_slab+0xa9/0x570
[    5.773618]  ___slab_alloc+0x375/0x540
[    5.773618]  ? pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  __slab_alloc+0x1c/0x38
[    5.773618]  __kmalloc_node_track_caller+0xc8/0x270
[    5.773618]  ? pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  devm_kmalloc+0x28/0x60
[    5.773618]  pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  really_probe+0x73/0x420
[    5.773618]  driver_probe_device+0x115/0x130
[    5.773618]  __driver_attach+0x103/0x110
[    5.773618]  ? driver_probe_device+0x130/0x130
[    5.773618]  bus_for_each_dev+0x67/0xc0
[    5.773618]  ? klist_add_tail+0x3b/0x70
[    5.773618]  bus_add_driver+0x41/0x260
[    5.773618]  ? pcie_port_setup+0x4d/0x4d
[    5.773618]  driver_register+0x5b/0xe0
[    5.773618]  ? pcie_port_setup+0x4d/0x4d
[    5.773618]  do_one_initcall+0x4e/0x1d4
[    5.773618]  ? init_setup+0x25/0x28
[    5.773618]  kernel_init_freeable+0x1c1/0x26e
[    5.773618]  ? loglevel+0x5b/0x5b
[    5.773618]  ? rest_init+0xb0/0xb0
[    5.773618]  kernel_init+0xa/0x110
[    5.773618]  ret_from_fork+0x22/0x40
[    5.773618] Modules linked in:
[    5.773618] CR2: 0000000000002088
[    5.773618] ---[ end trace 1030c9120a03d081 ]---

with his AMD machine with the following topology

  NUMA node0 CPU(s):     0,8,16,24
  NUMA node1 CPU(s):     2,10,18,26
  NUMA node2 CPU(s):     4,12,20,28
  NUMA node3 CPU(s):     6,14,22,30
  NUMA node4 CPU(s):     1,9,17,25
  NUMA node5 CPU(s):     3,11,19,27
  NUMA node6 CPU(s):     5,13,21,29
  NUMA node7 CPU(s):     7,15,23,31
[    0.007418] Early memory node ranges
[    0.007419]   node   1: [mem 0x0000000000001000-0x000000000008efff]
[    0.007420]   node   1: [mem 0x0000000000090000-0x000000000009ffff]
[    0.007422]   node   1: [mem 0x0000000000100000-0x000000005c3d6fff]
[    0.007422]   node   1: [mem 0x00000000643df000-0x0000000068ff7fff]
[    0.007423]   node   1: [mem 0x000000006c528000-0x000000006fffffff]
[    0.007424]   node   1: [mem 0x0000000100000000-0x000000047fffffff]
[    0.007425]   node   5: [mem 0x0000000480000000-0x000000087effffff]

and nr_cpus set to 4. The underlying reason is tha the device is bound to node 2 which doesn't have any memory and init_cpu_to_node only initializes memory-less nodes for possible cpus which nr_cpus restrics. This in turn means that proper zonelists are not allocated and the page allocator blows up.

Fix the issue by reworking how x86 initializes the memory less nodes. The current implementation is hacked into the workflow and it doesn't allow any flexibility. There is init_memory_less_node called for each offline node that has a CPU as already mentioned above. This will make sure that we will have a new online node without any memory. Much later on we build a zone list for this node and things seem to work, except they do not (e.g. due to nr_cpus). Not to mention that it doesn't really make much sense to consider an empty node as online because we just consider this node whenever we want to iterate nodes to use and empty node is obviously not the best candidate. This is all just too fragile.

---

Hi,
I am sending this as an RFC because I am not sure this is the proper way to go myself. I am especially not sure about other architectures supporting memoryless nodes (ppc and ia64 AFAICS or are there more?).

I would appreciate a help with those architectures because I couldn't really grasp how the memoryless nodes are really initialized there. E.g. ppc only seem to call setup_node_data for online nodes but I couldn't find any special treatment for nodes without any memory.

Any further help, comments are appreaciated!

 arch/x86/mm/numa.c | 27 +++------------------------
 mm/page_alloc.c    | 15 +++++++++------
 2 files changed, 12 insertions(+), 30 deletions(-)
arch/x86/mm/numa.c +3 -24
index 1308f5408bf7..b3621ee4dfe8 100644
@@ -216,8 +216,6 @@ static void __init alloc_node_data(int nid)
 
 	node_data[nid] = nd;
 	memset(NODE_DATA(nid), 0, sizeof(pg_data_t));
-
-	node_set_online(nid);
 }
 
 /**
@@ -570,7 +568,7 @@ static int __init numa_register_memblks(struct numa_meminfo *mi)
 		return -EINVAL;
 
 	/* Finally register nodes. */
-	for_each_node_mask(nid, node_possible_map) {
+	for_each_node_mask(nid, numa_nodes_parsed) {
 		u64 start = PFN_PHYS(max_pfn);
 		u64 end = 0;
 
@@ -581,9 +579,6 @@ static int __init numa_register_memblks(struct numa_meminfo *mi)
 			end = max(mi->blk[i].end, end);
 		}
 
-		if (start >= end)
-			continue;
-
 		/*
 		 * Don't confuse VM with a node that doesn't have the
 		 * minimum amount of memory:
@@ -592,6 +587,8 @@ static int __init numa_register_memblks(struct numa_meminfo *mi)
 			continue;
 
 		alloc_node_data(nid);
+		if (end)
+			node_set_online(nid);
 	}
 
 	/* Dump memblock with node info and return. */
@@ -721,21 +718,6 @@ void __init x86_numa_init(void)
 	numa_init(dummy_numa_init);
 }
 
-static void __init init_memory_less_node(int nid)
-{
-	unsigned long zones_size[MAX_NR_ZONES] = {0};
-	unsigned long zholes_size[MAX_NR_ZONES] = {0};
-
-	/* Allocate and initialize node data. Memory-less node is now online.*/
-	alloc_node_data(nid);
-	free_area_init_node(nid, zones_size, 0, zholes_size);
-
-	/*
-	 * All zonelists will be built later in start_kernel() after per cpu
-	 * areas are initialized.
-	 */
-}
-
 /*
  * Setup early cpu_to_node.
  *
@@ -763,9 +745,6 @@ void __init init_cpu_to_node(void)
 		if (node = NUMA_NO_NODE)
 			continue;
 
-		if (!node_online(node))
-			init_memory_less_node(node);
-
 		numa_set_node(cpu, node);
 	}
 }
mm/page_alloc.c +9 -6
index 2ec9cc407216..2e097f336126 100644
@@ -5361,10 +5361,11 @@ static void __build_all_zonelists(void *data)
 	if (self && !node_online(self->node_id)) {
 		build_zonelists(self);
 	} else {
-		for_each_online_node(nid) {
+		for_each_node(nid) {
 			pg_data_t *pgdat = NODE_DATA(nid);
 
-			build_zonelists(pgdat);
+			if (pgdat)
+				build_zonelists(pgdat);
 		}
 
 #ifdef CONFIG_HAVE_MEMORYLESS_NODES
@@ -6644,10 +6645,8 @@ static unsigned long __init find_min_pfn_for_node(int nid)
 	for_each_mem_pfn_range(i, nid, &start_pfn, NULL, NULL)
 		min_pfn = min(min_pfn, start_pfn);
 
-	if (min_pfn = ULONG_MAX) {
-		pr_warn("Could not find start_pfn for node %d\n", nid);
+	if (min_pfn = ULONG_MAX)
 		return 0;
-	}
 
 	return min_pfn;
 }
@@ -6991,8 +6990,12 @@ void __init free_area_init_nodes(unsigned long *max_zone_pfn)
 	mminit_verify_pageflags_layout();
 	setup_nr_node_ids();
 	zero_resv_unavail();
-	for_each_online_node(nid) {
+	for_each_node(nid) {
 		pg_data_t *pgdat = NODE_DATA(nid);
+
+		if (!pgdat)
+			continue;
+
 		free_area_init_node(nid, NULL,
 				find_min_pfn_for_node(nid), NULL);
 
Signature · 1 line
2.20.1
#1 lore raw
Quoted 96 lines · Michal Hocko

From: Michal Hocko <[email protected]>

Pingfan Liu has reported the following splat

[    5.772742] BUG: unable to handle kernel paging request at 0000000000002088
[    5.773618] PGD 0 P4D 0
[    5.773618] Oops: 0000 [#1] SMP NOPTI
[    5.773618] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.20.0-rc1+ #3
[    5.773618] Hardware name: Dell Inc. PowerEdge R7425/02MJ3T, BIOS 1.4.3 06/29/2018
[    5.773618] RIP: 0010:__alloc_pages_nodemask+0xe2/0x2a0
[    5.773618] Code: 00 00 44 89 ea 80 ca 80 41 83 f8 01 44 0f 44 ea 89 da c1 ea 08 83 e2 01 88 54 24 20 48 8b 54 24 08 48 85 d2 0f 85 46 01 00 00 <3b> 77 08 0f 82 3d 01 00 00 48 89 f8 44 89 ea 48 89
e1 44 89 e6 89
[    5.773618] RSP: 0018:ffffaa600005fb20 EFLAGS: 00010246
[    5.773618] RAX: 0000000000000000 RBX: 00000000006012c0 RCX: 0000000000000000
[    5.773618] RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000002080
[    5.773618] RBP: 00000000006012c0 R08: 0000000000000000 R09: 0000000000000002
[    5.773618] R10: 00000000006080c0 R11: 0000000000000002 R12: 0000000000000000
[    5.773618] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000002
[    5.773618] FS:  0000000000000000(0000) GS:ffff8c69afe00000(0000) knlGS:0000000000000000
[    5.773618] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    5.773618] CR2: 0000000000002088 CR3: 000000087e00a000 CR4: 00000000003406e0
[    5.773618] Call Trace:
[    5.773618]  new_slab+0xa9/0x570
[    5.773618]  ___slab_alloc+0x375/0x540
[    5.773618]  ? pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  __slab_alloc+0x1c/0x38
[    5.773618]  __kmalloc_node_track_caller+0xc8/0x270
[    5.773618]  ? pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  devm_kmalloc+0x28/0x60
[    5.773618]  pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  really_probe+0x73/0x420
[    5.773618]  driver_probe_device+0x115/0x130
[    5.773618]  __driver_attach+0x103/0x110
[    5.773618]  ? driver_probe_device+0x130/0x130
[    5.773618]  bus_for_each_dev+0x67/0xc0
[    5.773618]  ? klist_add_tail+0x3b/0x70
[    5.773618]  bus_add_driver+0x41/0x260
[    5.773618]  ? pcie_port_setup+0x4d/0x4d
[    5.773618]  driver_register+0x5b/0xe0
[    5.773618]  ? pcie_port_setup+0x4d/0x4d
[    5.773618]  do_one_initcall+0x4e/0x1d4
[    5.773618]  ? init_setup+0x25/0x28
[    5.773618]  kernel_init_freeable+0x1c1/0x26e
[    5.773618]  ? loglevel+0x5b/0x5b
[    5.773618]  ? rest_init+0xb0/0xb0
[    5.773618]  kernel_init+0xa/0x110
[    5.773618]  ret_from_fork+0x22/0x40
[    5.773618] Modules linked in:
[    5.773618] CR2: 0000000000002088
[    5.773618] ---[ end trace 1030c9120a03d081 ]---

with his AMD machine with the following topology

  NUMA node0 CPU(s):     0,8,16,24
  NUMA node1 CPU(s):     2,10,18,26
  NUMA node2 CPU(s):     4,12,20,28
  NUMA node3 CPU(s):     6,14,22,30
  NUMA node4 CPU(s):     1,9,17,25
  NUMA node5 CPU(s):     3,11,19,27
  NUMA node6 CPU(s):     5,13,21,29
  NUMA node7 CPU(s):     7,15,23,31
[    0.007418] Early memory node ranges
[    0.007419]   node   1: [mem 0x0000000000001000-0x000000000008efff]
[    0.007420]   node   1: [mem 0x0000000000090000-0x000000000009ffff]
[    0.007422]   node   1: [mem 0x0000000000100000-0x000000005c3d6fff]
[    0.007422]   node   1: [mem 0x00000000643df000-0x0000000068ff7fff]
[    0.007423]   node   1: [mem 0x000000006c528000-0x000000006fffffff]
[    0.007424]   node   1: [mem 0x0000000100000000-0x000000047fffffff]
[    0.007425]   node   5: [mem 0x0000000480000000-0x000000087effffff]

and nr_cpus set to 4. The underlying reason is tha the device is bound to node 2 which doesn't have any memory and init_cpu_to_node only initializes memory-less nodes for possible cpus which nr_cpus restrics. This in turn means that proper zonelists are not allocated and the page allocator blows up.

Fix the issue by reworking how x86 initializes the memory less nodes. The current implementation is hacked into the workflow and it doesn't allow any flexibility. There is init_memory_less_node called for each offline node that has a CPU as already mentioned above. This will make sure that we will have a new online node without any memory. Much later on we build a zone list for this node and things seem to work, except they do not (e.g. due to nr_cpus). Not to mention that it doesn't really make much sense to consider an empty node as online because we just consider this node whenever we want to iterate nodes to use and empty node is obviously not the best candidate. This is all just too fragile.

---

Hi,
I am sending this as an RFC because I am not sure this is the proper way to go myself. I am especially not sure about other architectures supporting memoryless nodes (ppc and ia64 AFAICS or are there more?).

Quoted 4 lines

I would appreciate a help with those architectures because I couldn't really grasp how the memoryless nodes are really initialized there. E.g. ppc only seem to call setup_node_data for online nodes but I couldn't find any special treatment for nodes without any memory.

We have a somewhat dubious hack in our hotplug code, see:

e67e02a544e9 ("powerpc/pseries: Fix cpu hotplug crash with memoryless nodes")

Which basically onlines the node when we hotplug a CPU into it.

cheers

#2 lore raw
Quoted 103 lines · Michael Ellerman
Quoted 96 lines · Michal Hocko

From: Michal Hocko <[email protected]>

Pingfan Liu has reported the following splat

[    5.772742] BUG: unable to handle kernel paging request at 0000000000002088
[    5.773618] PGD 0 P4D 0
[    5.773618] Oops: 0000 [#1] SMP NOPTI
[    5.773618] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.20.0-rc1+ #3
[    5.773618] Hardware name: Dell Inc. PowerEdge R7425/02MJ3T, BIOS 1.4.3 06/29/2018
[    5.773618] RIP: 0010:__alloc_pages_nodemask+0xe2/0x2a0
[    5.773618] Code: 00 00 44 89 ea 80 ca 80 41 83 f8 01 44 0f 44 ea 89 da c1 ea 08 83 e2 01 88 54 24 20 48 8b 54 24 08 48 85 d2 0f 85 46 01 00 00 <3b> 77 08 0f 82 3d 01 00 00 48 89 f8 44 89 ea 48 89
e1 44 89 e6 89
[    5.773618] RSP: 0018:ffffaa600005fb20 EFLAGS: 00010246
[    5.773618] RAX: 0000000000000000 RBX: 00000000006012c0 RCX: 0000000000000000
[    5.773618] RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000002080
[    5.773618] RBP: 00000000006012c0 R08: 0000000000000000 R09: 0000000000000002
[    5.773618] R10: 00000000006080c0 R11: 0000000000000002 R12: 0000000000000000
[    5.773618] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000002
[    5.773618] FS:  0000000000000000(0000) GS:ffff8c69afe00000(0000) knlGS:0000000000000000
[    5.773618] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    5.773618] CR2: 0000000000002088 CR3: 000000087e00a000 CR4: 00000000003406e0
[    5.773618] Call Trace:
[    5.773618]  new_slab+0xa9/0x570
[    5.773618]  ___slab_alloc+0x375/0x540
[    5.773618]  ? pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  __slab_alloc+0x1c/0x38
[    5.773618]  __kmalloc_node_track_caller+0xc8/0x270
[    5.773618]  ? pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  devm_kmalloc+0x28/0x60
[    5.773618]  pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  really_probe+0x73/0x420
[    5.773618]  driver_probe_device+0x115/0x130
[    5.773618]  __driver_attach+0x103/0x110
[    5.773618]  ? driver_probe_device+0x130/0x130
[    5.773618]  bus_for_each_dev+0x67/0xc0
[    5.773618]  ? klist_add_tail+0x3b/0x70
[    5.773618]  bus_add_driver+0x41/0x260
[    5.773618]  ? pcie_port_setup+0x4d/0x4d
[    5.773618]  driver_register+0x5b/0xe0
[    5.773618]  ? pcie_port_setup+0x4d/0x4d
[    5.773618]  do_one_initcall+0x4e/0x1d4
[    5.773618]  ? init_setup+0x25/0x28
[    5.773618]  kernel_init_freeable+0x1c1/0x26e
[    5.773618]  ? loglevel+0x5b/0x5b
[    5.773618]  ? rest_init+0xb0/0xb0
[    5.773618]  kernel_init+0xa/0x110
[    5.773618]  ret_from_fork+0x22/0x40
[    5.773618] Modules linked in:
[    5.773618] CR2: 0000000000002088
[    5.773618] ---[ end trace 1030c9120a03d081 ]---

with his AMD machine with the following topology

  NUMA node0 CPU(s):     0,8,16,24
  NUMA node1 CPU(s):     2,10,18,26
  NUMA node2 CPU(s):     4,12,20,28
  NUMA node3 CPU(s):     6,14,22,30
  NUMA node4 CPU(s):     1,9,17,25
  NUMA node5 CPU(s):     3,11,19,27
  NUMA node6 CPU(s):     5,13,21,29
  NUMA node7 CPU(s):     7,15,23,31
[    0.007418] Early memory node ranges
[    0.007419]   node   1: [mem 0x0000000000001000-0x000000000008efff]
[    0.007420]   node   1: [mem 0x0000000000090000-0x000000000009ffff]
[    0.007422]   node   1: [mem 0x0000000000100000-0x000000005c3d6fff]
[    0.007422]   node   1: [mem 0x00000000643df000-0x0000000068ff7fff]
[    0.007423]   node   1: [mem 0x000000006c528000-0x000000006fffffff]
[    0.007424]   node   1: [mem 0x0000000100000000-0x000000047fffffff]
[    0.007425]   node   5: [mem 0x0000000480000000-0x000000087effffff]

and nr_cpus set to 4. The underlying reason is tha the device is bound to node 2 which doesn't have any memory and init_cpu_to_node only initializes memory-less nodes for possible cpus which nr_cpus restrics. This in turn means that proper zonelists are not allocated and the page allocator blows up.

Fix the issue by reworking how x86 initializes the memory less nodes. The current implementation is hacked into the workflow and it doesn't allow any flexibility. There is init_memory_less_node called for each offline node that has a CPU as already mentioned above. This will make sure that we will have a new online node without any memory. Much later on we build a zone list for this node and things seem to work, except they do not (e.g. due to nr_cpus). Not to mention that it doesn't really make much sense to consider an empty node as online because we just consider this node whenever we want to iterate nodes to use and empty node is obviously not the best candidate. This is all just too fragile.

---

Hi,
I am sending this as an RFC because I am not sure this is the proper way to go myself. I am especially not sure about other architectures supporting memoryless nodes (ppc and ia64 AFAICS or are there more?).

Quoted 4 lines

I would appreciate a help with those architectures because I couldn't really grasp how the memoryless nodes are really initialized there. E.g. ppc only seem to call setup_node_data for online nodes but I couldn't find any special treatment for nodes without any memory.

Quoted 5 lines

We have a somewhat dubious hack in our hotplug code, see:

e67e02a544e9 ("powerpc/pseries: Fix cpu hotplug crash with memoryless nodes")

Which basically onlines the node when we hotplug a CPU into it.

Hmm, interesting. So what happens if somebody tries to allocate a memory from a node when it is not online yet? E.g. something like the above.

And do I get it right that this patch will not break the current ppc code?

Signature · 2 lines
Michal Hocko
SUSE Labs
#3 lore raw
In reply to Michael Ellerman

[...]

Quoted 6 lines
Quoted 5 lines

I would appreciate a help with those architectures because I couldn't really grasp how the memoryless nodes are really initialized there. E.g. ppc only seem to call setup_node_data for online nodes but I couldn't find any special treatment for nodes without any memory.

Quoted 6 lines

We have a somewhat dubious hack in our hotplug code, see:

e67e02a544e9 ("powerpc/pseries: Fix cpu hotplug crash with memoryless nodes")

Which basically onlines the node when we hotplug a CPU into it.

This bug should be related with the present state of numa node during boot time. On PowerNV and PSeries, the boot code seems not to bring up all nodes if memoryless. Then it can not avoid this bug.

Thanks,
Pingfan

#4 lore raw
In reply to Michal Hocko

a friendly ping for this. Does anybody see any problem with this approach?

Quoted 227 lines · Michal Hocko

From: Michal Hocko <[email protected]>

Pingfan Liu has reported the following splat

[    5.772742] BUG: unable to handle kernel paging request at 0000000000002088
[    5.773618] PGD 0 P4D 0
[    5.773618] Oops: 0000 [#1] SMP NOPTI
[    5.773618] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.20.0-rc1+ #3
[    5.773618] Hardware name: Dell Inc. PowerEdge R7425/02MJ3T, BIOS 1.4.3 06/29/2018
[    5.773618] RIP: 0010:__alloc_pages_nodemask+0xe2/0x2a0
[    5.773618] Code: 00 00 44 89 ea 80 ca 80 41 83 f8 01 44 0f 44 ea 89 da c1 ea 08 83 e2 01 88 54 24 20 48 8b 54 24 08 48 85 d2 0f 85 46 01 00 00 <3b> 77 08 0f 82 3d 01 00 00 48 89 f8 44 89 ea 48 89
e1 44 89 e6 89
[    5.773618] RSP: 0018:ffffaa600005fb20 EFLAGS: 00010246
[    5.773618] RAX: 0000000000000000 RBX: 00000000006012c0 RCX: 0000000000000000
[    5.773618] RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000002080
[    5.773618] RBP: 00000000006012c0 R08: 0000000000000000 R09: 0000000000000002
[    5.773618] R10: 00000000006080c0 R11: 0000000000000002 R12: 0000000000000000
[    5.773618] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000002
[    5.773618] FS:  0000000000000000(0000) GS:ffff8c69afe00000(0000) knlGS:0000000000000000
[    5.773618] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    5.773618] CR2: 0000000000002088 CR3: 000000087e00a000 CR4: 00000000003406e0
[    5.773618] Call Trace:
[    5.773618]  new_slab+0xa9/0x570
[    5.773618]  ___slab_alloc+0x375/0x540
[    5.773618]  ? pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  __slab_alloc+0x1c/0x38
[    5.773618]  __kmalloc_node_track_caller+0xc8/0x270
[    5.773618]  ? pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  devm_kmalloc+0x28/0x60
[    5.773618]  pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  really_probe+0x73/0x420
[    5.773618]  driver_probe_device+0x115/0x130
[    5.773618]  __driver_attach+0x103/0x110
[    5.773618]  ? driver_probe_device+0x130/0x130
[    5.773618]  bus_for_each_dev+0x67/0xc0
[    5.773618]  ? klist_add_tail+0x3b/0x70
[    5.773618]  bus_add_driver+0x41/0x260
[    5.773618]  ? pcie_port_setup+0x4d/0x4d
[    5.773618]  driver_register+0x5b/0xe0
[    5.773618]  ? pcie_port_setup+0x4d/0x4d
[    5.773618]  do_one_initcall+0x4e/0x1d4
[    5.773618]  ? init_setup+0x25/0x28
[    5.773618]  kernel_init_freeable+0x1c1/0x26e
[    5.773618]  ? loglevel+0x5b/0x5b
[    5.773618]  ? rest_init+0xb0/0xb0
[    5.773618]  kernel_init+0xa/0x110
[    5.773618]  ret_from_fork+0x22/0x40
[    5.773618] Modules linked in:
[    5.773618] CR2: 0000000000002088
[    5.773618] ---[ end trace 1030c9120a03d081 ]---

with his AMD machine with the following topology

  NUMA node0 CPU(s):     0,8,16,24
  NUMA node1 CPU(s):     2,10,18,26
  NUMA node2 CPU(s):     4,12,20,28
  NUMA node3 CPU(s):     6,14,22,30
  NUMA node4 CPU(s):     1,9,17,25
  NUMA node5 CPU(s):     3,11,19,27
  NUMA node6 CPU(s):     5,13,21,29
  NUMA node7 CPU(s):     7,15,23,31
[    0.007418] Early memory node ranges
[    0.007419]   node   1: [mem 0x0000000000001000-0x000000000008efff]
[    0.007420]   node   1: [mem 0x0000000000090000-0x000000000009ffff]
[    0.007422]   node   1: [mem 0x0000000000100000-0x000000005c3d6fff]
[    0.007422]   node   1: [mem 0x00000000643df000-0x0000000068ff7fff]
[    0.007423]   node   1: [mem 0x000000006c528000-0x000000006fffffff]
[    0.007424]   node   1: [mem 0x0000000100000000-0x000000047fffffff]
[    0.007425]   node   5: [mem 0x0000000480000000-0x000000087effffff]

and nr_cpus set to 4. The underlying reason is tha the device is bound to node 2 which doesn't have any memory and init_cpu_to_node only initializes memory-less nodes for possible cpus which nr_cpus restrics. This in turn means that proper zonelists are not allocated and the page allocator blows up.

Fix the issue by reworking how x86 initializes the memory less nodes. The current implementation is hacked into the workflow and it doesn't allow any flexibility. There is init_memory_less_node called for each offline node that has a CPU as already mentioned above. This will make sure that we will have a new online node without any memory. Much later on we build a zone list for this node and things seem to work, except they do not (e.g. due to nr_cpus). Not to mention that it doesn't really make much sense to consider an empty node as online because we just consider this node whenever we want to iterate nodes to use and empty node is obviously not the best candidate. This is all just too fragile.

---

Hi,
I am sending this as an RFC because I am not sure this is the proper way to go myself. I am especially not sure about other architectures supporting memoryless nodes (ppc and ia64 AFAICS or are there more?).

I would appreciate a help with those architectures because I couldn't really grasp how the memoryless nodes are really initialized there. E.g. ppc only seem to call setup_node_data for online nodes but I couldn't find any special treatment for nodes without any memory.

Any further help, comments are appreaciated!

 arch/x86/mm/numa.c | 27 +++------------------------
 mm/page_alloc.c    | 15 +++++++++------
 2 files changed, 12 insertions(+), 30 deletions(-)
arch/x86/mm/numa.c +3 -24
index 1308f5408bf7..b3621ee4dfe8 100644
@@ -216,8 +216,6 @@ static void __init alloc_node_data(int nid)
 
 	node_data[nid] = nd;
 	memset(NODE_DATA(nid), 0, sizeof(pg_data_t));
-
-	node_set_online(nid);
 }
 
 /**
@@ -570,7 +568,7 @@ static int __init numa_register_memblks(struct numa_meminfo *mi)
 		return -EINVAL;
 
 	/* Finally register nodes. */
-	for_each_node_mask(nid, node_possible_map) {
+	for_each_node_mask(nid, numa_nodes_parsed) {
 		u64 start = PFN_PHYS(max_pfn);
 		u64 end = 0;
 
@@ -581,9 +579,6 @@ static int __init numa_register_memblks(struct numa_meminfo *mi)
 			end = max(mi->blk[i].end, end);
 		}
 
-		if (start >= end)
-			continue;
-
 		/*
 		 * Don't confuse VM with a node that doesn't have the
 		 * minimum amount of memory:
@@ -592,6 +587,8 @@ static int __init numa_register_memblks(struct numa_meminfo *mi)
 			continue;
 
 		alloc_node_data(nid);
+		if (end)
+			node_set_online(nid);
 	}
 
 	/* Dump memblock with node info and return. */
@@ -721,21 +718,6 @@ void __init x86_numa_init(void)
 	numa_init(dummy_numa_init);
 }
 
-static void __init init_memory_less_node(int nid)
-{
-	unsigned long zones_size[MAX_NR_ZONES] = {0};
-	unsigned long zholes_size[MAX_NR_ZONES] = {0};
-
-	/* Allocate and initialize node data. Memory-less node is now online.*/
-	alloc_node_data(nid);
-	free_area_init_node(nid, zones_size, 0, zholes_size);
-
-	/*
-	 * All zonelists will be built later in start_kernel() after per cpu
-	 * areas are initialized.
-	 */
-}
-
 /*
  * Setup early cpu_to_node.
  *
@@ -763,9 +745,6 @@ void __init init_cpu_to_node(void)
 		if (node = NUMA_NO_NODE)
 			continue;
 
-		if (!node_online(node))
-			init_memory_less_node(node);
-
 		numa_set_node(cpu, node);
 	}
 }
mm/page_alloc.c +9 -6
index 2ec9cc407216..2e097f336126 100644
@@ -5361,10 +5361,11 @@ static void __build_all_zonelists(void *data)
 	if (self && !node_online(self->node_id)) {
 		build_zonelists(self);
 	} else {
-		for_each_online_node(nid) {
+		for_each_node(nid) {
 			pg_data_t *pgdat = NODE_DATA(nid);
 
-			build_zonelists(pgdat);
+			if (pgdat)
+				build_zonelists(pgdat);
 		}
 
 #ifdef CONFIG_HAVE_MEMORYLESS_NODES
@@ -6644,10 +6645,8 @@ static unsigned long __init find_min_pfn_for_node(int nid)
 	for_each_mem_pfn_range(i, nid, &start_pfn, NULL, NULL)
 		min_pfn = min(min_pfn, start_pfn);
 
-	if (min_pfn = ULONG_MAX) {
-		pr_warn("Could not find start_pfn for node %d\n", nid);
+	if (min_pfn = ULONG_MAX)
 		return 0;
-	}
 
 	return min_pfn;
 }
@@ -6991,8 +6990,12 @@ void __init free_area_init_nodes(unsigned long *max_zone_pfn)
 	mminit_verify_pageflags_layout();
 	setup_nr_node_ids();
 	zero_resv_unavail();
-	for_each_online_node(nid) {
+	for_each_node(nid) {
 		pg_data_t *pgdat = NODE_DATA(nid);
+
+		if (!pgdat)
+			continue;
+
 		free_area_init_node(nid, NULL,
 				find_min_pfn_for_node(nid), NULL);
 
Signature · 1 line
2.20.1
Signature · 2 lines
Michal Hocko
SUSE Labs
#5 lore raw
Quoted 2 lines · Michal Hocko

a friendly ping for this. Does anybody see any problem with this approach?

FWIW, it looks fine to me.

It'd just be nice to have a few more words in the changelog about *how* the x86 init was reworked ;-)

Quoted 233 lines · Michal Hocko
Quoted 227 lines

From: Michal Hocko <[email protected]>

Pingfan Liu has reported the following splat

[    5.772742] BUG: unable to handle kernel paging request at 0000000000002088
[    5.773618] PGD 0 P4D 0
[    5.773618] Oops: 0000 [#1] SMP NOPTI
[    5.773618] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.20.0-rc1+ #3
[    5.773618] Hardware name: Dell Inc. PowerEdge R7425/02MJ3T, BIOS 1.4.3 06/29/2018
[    5.773618] RIP: 0010:__alloc_pages_nodemask+0xe2/0x2a0
[    5.773618] Code: 00 00 44 89 ea 80 ca 80 41 83 f8 01 44 0f 44 ea 89 da c1 ea 08 83 e2 01 88 54 24 20 48 8b 54 24 08 48 85 d2 0f 85 46 01 00 00 <3b> 77 08 0f 82 3d 01 00 00 48 89 f8 44 89 ea 48 89
e1 44 89 e6 89
[    5.773618] RSP: 0018:ffffaa600005fb20 EFLAGS: 00010246
[    5.773618] RAX: 0000000000000000 RBX: 00000000006012c0 RCX: 0000000000000000
[    5.773618] RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000002080
[    5.773618] RBP: 00000000006012c0 R08: 0000000000000000 R09: 0000000000000002
[    5.773618] R10: 00000000006080c0 R11: 0000000000000002 R12: 0000000000000000
[    5.773618] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000002
[    5.773618] FS:  0000000000000000(0000) GS:ffff8c69afe00000(0000) knlGS:0000000000000000
[    5.773618] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    5.773618] CR2: 0000000000002088 CR3: 000000087e00a000 CR4: 00000000003406e0
[    5.773618] Call Trace:
[    5.773618]  new_slab+0xa9/0x570
[    5.773618]  ___slab_alloc+0x375/0x540
[    5.773618]  ? pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  __slab_alloc+0x1c/0x38
[    5.773618]  __kmalloc_node_track_caller+0xc8/0x270
[    5.773618]  ? pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  devm_kmalloc+0x28/0x60
[    5.773618]  pinctrl_bind_pins+0x2b/0x2a0
[    5.773618]  really_probe+0x73/0x420
[    5.773618]  driver_probe_device+0x115/0x130
[    5.773618]  __driver_attach+0x103/0x110
[    5.773618]  ? driver_probe_device+0x130/0x130
[    5.773618]  bus_for_each_dev+0x67/0xc0
[    5.773618]  ? klist_add_tail+0x3b/0x70
[    5.773618]  bus_add_driver+0x41/0x260
[    5.773618]  ? pcie_port_setup+0x4d/0x4d
[    5.773618]  driver_register+0x5b/0xe0
[    5.773618]  ? pcie_port_setup+0x4d/0x4d
[    5.773618]  do_one_initcall+0x4e/0x1d4
[    5.773618]  ? init_setup+0x25/0x28
[    5.773618]  kernel_init_freeable+0x1c1/0x26e
[    5.773618]  ? loglevel+0x5b/0x5b
[    5.773618]  ? rest_init+0xb0/0xb0
[    5.773618]  kernel_init+0xa/0x110
[    5.773618]  ret_from_fork+0x22/0x40
[    5.773618] Modules linked in:
[    5.773618] CR2: 0000000000002088
[    5.773618] ---[ end trace 1030c9120a03d081 ]---

with his AMD machine with the following topology

  NUMA node0 CPU(s):     0,8,16,24
  NUMA node1 CPU(s):     2,10,18,26
  NUMA node2 CPU(s):     4,12,20,28
  NUMA node3 CPU(s):     6,14,22,30
  NUMA node4 CPU(s):     1,9,17,25
  NUMA node5 CPU(s):     3,11,19,27
  NUMA node6 CPU(s):     5,13,21,29
  NUMA node7 CPU(s):     7,15,23,31
[    0.007418] Early memory node ranges
[    0.007419]   node   1: [mem 0x0000000000001000-0x000000000008efff]
[    0.007420]   node   1: [mem 0x0000000000090000-0x000000000009ffff]
[    0.007422]   node   1: [mem 0x0000000000100000-0x000000005c3d6fff]
[    0.007422]   node   1: [mem 0x00000000643df000-0x0000000068ff7fff]
[    0.007423]   node   1: [mem 0x000000006c528000-0x000000006fffffff]
[    0.007424]   node   1: [mem 0x0000000100000000-0x000000047fffffff]
[    0.007425]   node   5: [mem 0x0000000480000000-0x000000087effffff]

and nr_cpus set to 4. The underlying reason is tha the device is bound to node 2 which doesn't have any memory and init_cpu_to_node only initializes memory-less nodes for possible cpus which nr_cpus restrics. This in turn means that proper zonelists are not allocated and the page allocator blows up.

Fix the issue by reworking how x86 initializes the memory less nodes. The current implementation is hacked into the workflow and it doesn't allow any flexibility. There is init_memory_less_node called for each offline node that has a CPU as already mentioned above. This will make sure that we will have a new online node without any memory. Much later on we build a zone list for this node and things seem to work, except they do not (e.g. due to nr_cpus). Not to mention that it doesn't really make much sense to consider an empty node as online because we just consider this node whenever we want to iterate nodes to use and empty node is obviously not the best candidate. This is all just too fragile.

---

Hi,
I am sending this as an RFC because I am not sure this is the proper way to go myself. I am especially not sure about other architectures supporting memoryless nodes (ppc and ia64 AFAICS or are there more?).

I would appreciate a help with those architectures because I couldn't really grasp how the memoryless nodes are really initialized there. E.g. ppc only seem to call setup_node_data for online nodes but I couldn't find any special treatment for nodes without any memory.

Any further help, comments are appreaciated!

 arch/x86/mm/numa.c | 27 +++------------------------
 mm/page_alloc.c    | 15 +++++++++------
 2 files changed, 12 insertions(+), 30 deletions(-)
arch/x86/mm/numa.c +3 -24
index 1308f5408bf7..b3621ee4dfe8 100644
@@ -216,8 +216,6 @@ static void __init alloc_node_data(int nid)
 
 	node_data[nid] = nd;
 	memset(NODE_DATA(nid), 0, sizeof(pg_data_t));
-
-	node_set_online(nid);
 }
 
 /**
@@ -570,7 +568,7 @@ static int __init numa_register_memblks(struct numa_meminfo *mi)
 		return -EINVAL;
 
 	/* Finally register nodes. */
-	for_each_node_mask(nid, node_possible_map) {
+	for_each_node_mask(nid, numa_nodes_parsed) {
 		u64 start = PFN_PHYS(max_pfn);
 		u64 end = 0;
 
@@ -581,9 +579,6 @@ static int __init numa_register_memblks(struct numa_meminfo *mi)
 			end = max(mi->blk[i].end, end);
 		}
 
-		if (start >= end)
-			continue;
-
 		/*
 		 * Don't confuse VM with a node that doesn't have the
 		 * minimum amount of memory:
@@ -592,6 +587,8 @@ static int __init numa_register_memblks(struct numa_meminfo *mi)
 			continue;
 
 		alloc_node_data(nid);
+		if (end)
+			node_set_online(nid);
 	}
 
 	/* Dump memblock with node info and return. */
@@ -721,21 +718,6 @@ void __init x86_numa_init(void)
 	numa_init(dummy_numa_init);
 }
 
-static void __init init_memory_less_node(int nid)
-{
-	unsigned long zones_size[MAX_NR_ZONES] = {0};
-	unsigned long zholes_size[MAX_NR_ZONES] = {0};
-
-	/* Allocate and initialize node data. Memory-less node is now online.*/
-	alloc_node_data(nid);
-	free_area_init_node(nid, zones_size, 0, zholes_size);
-
-	/*
-	 * All zonelists will be built later in start_kernel() after per cpu
-	 * areas are initialized.
-	 */
-}
-
 /*
  * Setup early cpu_to_node.
  *
@@ -763,9 +745,6 @@ void __init init_cpu_to_node(void)
 		if (node = NUMA_NO_NODE)
 			continue;
 
-		if (!node_online(node))
-			init_memory_less_node(node);
-
 		numa_set_node(cpu, node);
 	}
 }
mm/page_alloc.c +9 -6
index 2ec9cc407216..2e097f336126 100644
@@ -5361,10 +5361,11 @@ static void __build_all_zonelists(void *data)
 	if (self && !node_online(self->node_id)) {
 		build_zonelists(self);
 	} else {
-		for_each_online_node(nid) {
+		for_each_node(nid) {
 			pg_data_t *pgdat = NODE_DATA(nid);
 
-			build_zonelists(pgdat);
+			if (pgdat)
+				build_zonelists(pgdat);
 		}
 
 #ifdef CONFIG_HAVE_MEMORYLESS_NODES
@@ -6644,10 +6645,8 @@ static unsigned long __init find_min_pfn_for_node(int nid)
 	for_each_mem_pfn_range(i, nid, &start_pfn, NULL, NULL)
 		min_pfn = min(min_pfn, start_pfn);
 
-	if (min_pfn = ULONG_MAX) {
-		pr_warn("Could not find start_pfn for node %d\n", nid);
+	if (min_pfn = ULONG_MAX)
 		return 0;
-	}
 
 	return min_pfn;
 }
@@ -6991,8 +6990,12 @@ void __init free_area_init_nodes(unsigned long *max_zone_pfn)
 	mminit_verify_pageflags_layout();
 	setup_nr_node_ids();
 	zero_resv_unavail();
-	for_each_online_node(nid) {
+	for_each_node(nid) {
 		pg_data_t *pgdat = NODE_DATA(nid);
+
+		if (!pgdat)
+			continue;
+
 		free_area_init_node(nid, NULL,
 				find_min_pfn_for_node(nid), NULL);
 
Signature · 1 line
2.20.1
Signature · 2 lines
Michal Hocko
SUSE Labs
Signature · 2 lines
Sincerely yours,
Mike.
#6 lore raw
Quoted 8 lines · Mike Rapoport
Quoted 2 lines · Michal Hocko

a friendly ping for this. Does anybody see any problem with this approach?

FWIW, it looks fine to me.

It'd just be nice to have a few more words in the changelog about *how* the x86 init was reworked ;-)

Heh, I thought it was there but nope... It probably just existed in my head. Sorry about that. What about the following paragraphs added? "
The new code relies on the arch specific initialization to allocate all possible NUMA nodes (including memory less) - numa_register_memblks in this case. Generic code then initializes both zonelists (__build_all_zonelists) and allocator internals (free_area_init_nodes) for all non-null pgdats rather than online ones.

For the x86 specific part also do not make new node online in alloc_node_data because this is too early to know that. numa_register_memblks knows that a node has some memory so it can make the node online appropriately. init_memory_less_node hack can be safely removed altogether now. "

Signature · 2 lines
Michal Hocko
SUSE Labs
#7 lore raw
Quoted 19 lines · Michal Hocko
Quoted 8 lines · Mike Rapoport
Quoted 2 lines · Michal Hocko

a friendly ping for this. Does anybody see any problem with this approach?

FWIW, it looks fine to me.

It'd just be nice to have a few more words in the changelog about *how* the x86 init was reworked ;-)

Heh, I thought it was there but nope... It probably just existed in my head. Sorry about that. What about the following paragraphs added? "
The new code relies on the arch specific initialization to allocate all possible NUMA nodes (including memory less) - numa_register_memblks in this case. Generic code then initializes both zonelists (__build_all_zonelists) and allocator internals (free_area_init_nodes) for all non-null pgdats rather than online ones.

Quoted 5 lines

For the x86 specific part also do not make new node online in alloc_node_data because this is too early to know that. numa_register_memblks knows that a node has some memory so it can make the node online appropriately. init_memory_less_node hack can be safely removed altogether now. "

LGTM, thanks!

Quoted 4 lines
Signature · 2 lines
Michal Hocko
SUSE Labs
Signature · 2 lines
Sincerely yours,
Mike.
#8 lore raw
In reply to Michal Hocko
Quoted 5 lines · Michal Hocko

and nr_cpus set to 4. The underlying reason is tha the device is bound to node 2 which doesn't have any memory and init_cpu_to_node only initializes memory-less nodes for possible cpus which nr_cpus restrics. This in turn means that proper zonelists are not allocated and the page allocator blows up.

This looks OK to me.

Could we add a few DEBUG_VM checks that *look* for these invalid zonelists? Or, would our existing list debugging have caught this?

Basically, is this bug also a sign that we need better debugging around this?

#9 lore raw
Quoted 11 lines · Dave Hansen
Quoted 5 lines · Michal Hocko

and nr_cpus set to 4. The underlying reason is tha the device is bound to node 2 which doesn't have any memory and init_cpu_to_node only initializes memory-less nodes for possible cpus which nr_cpus restrics. This in turn means that proper zonelists are not allocated and the page allocator blows up.

This looks OK to me.

Could we add a few DEBUG_VM checks that *look* for these invalid zonelists? Or, would our existing list debugging have caught this?

Currently we simply blow up because those zonelists are NULL. I do not think we have a way to check whether an existing zonelist is actually _correct_ other thatn check it for NULL. But what would we do in the later case?

Quoted 2 lines

Basically, is this bug also a sign that we need better debugging around this?

My earlier patch had a debugging printk to display the zonelists and that might be worthwhile I guess. Basically something like this

mm/page_alloc.c +5 -0
index 2e097f336126..c30d59f803fb 100644
@@ -5259,6 +5259,11 @@ static void build_zonelists(pg_data_t *pgdat)
 
 	build_zonelists_in_node_order(pgdat, node_order, nr_nodes);
 	build_thisnode_zonelists(pgdat);
+
+	pr_info("node[%d] zonelist: ", pgdat->node_id);
+	for_each_zone_zonelist(zone, z, &pgdat->node_zonelists[ZONELIST_FALLBACK], MAX_NR_ZONES-1)
+		pr_cont("%d:%s ", zone_to_nid(zone), zone->name);
+	pr_cont("\n");
 }
 
 #ifdef CONFIG_HAVE_MEMORYLESS_NODES
Signature · 2 lines
Michal Hocko
SUSE Labs
#10 lore raw
Quoted 29 lines · Michal Hocko
Quoted 11 lines · Dave Hansen
Quoted 5 lines · Michal Hocko

and nr_cpus set to 4. The underlying reason is tha the device is bound to node 2 which doesn't have any memory and init_cpu_to_node only initializes memory-less nodes for possible cpus which nr_cpus restrics. This in turn means that proper zonelists are not allocated and the page allocator blows up.

This looks OK to me.

Could we add a few DEBUG_VM checks that *look* for these invalid zonelists? Or, would our existing list debugging have caught this?

Currently we simply blow up because those zonelists are NULL. I do not think we have a way to check whether an existing zonelist is actually _correct_ other thatn check it for NULL. But what would we do in the later case?

Quoted 2 lines

Basically, is this bug also a sign that we need better debugging around this?

My earlier patch had a debugging printk to display the zonelists and that might be worthwhile I guess. Basically something like this

mm/page_alloc.c +0 -0
index 2e097f336126..c30d59f803fb 100644

mm/page_alloc.c static void build_zonelists(pg_data_t *pgdat) · line 5267

Quoted 9 lines
mm/page_alloc.c +5 -0
@@ -5259,6 +5259,11 @@ static void build_zonelists(pg_data_t *pgdat)
 
 	build_zonelists_in_node_order(pgdat, node_order, nr_nodes);
 	build_thisnode_zonelists(pgdat);
+
+	pr_info("node[%d] zonelist: ", pgdat->node_id);
+	for_each_zone_zonelist(zone, z, &pgdat->node_zonelists[ZONELIST_FALLBACK], MAX_NR_ZONES-1)
+		pr_cont("%d:%s ", zone_to_nid(zone), zone->name);
+	pr_cont("\n");
 }

Looks like this patch fell through the cracks - any update on this?

Thanks,

Ingo

#11 lore raw
Quoted 33 lines · Ingo Molnar
Quoted 30 lines · Michal Hocko
Quoted 11 lines · Dave Hansen
Quoted 5 lines · Michal Hocko

and nr_cpus set to 4. The underlying reason is tha the device is bound to node 2 which doesn't have any memory and init_cpu_to_node only initializes memory-less nodes for possible cpus which nr_cpus restrics. This in turn means that proper zonelists are not allocated and the page allocator blows up.

This looks OK to me.

Could we add a few DEBUG_VM checks that *look* for these invalid zonelists? Or, would our existing list debugging have caught this?

Currently we simply blow up because those zonelists are NULL. I do not think we have a way to check whether an existing zonelist is actually _correct_ other thatn check it for NULL. But what would we do in the later case?

Quoted 2 lines

Basically, is this bug also a sign that we need better debugging around this?

My earlier patch had a debugging printk to display the zonelists and that might be worthwhile I guess. Basically something like this

mm/page_alloc.c +0 -0
index 2e097f336126..c30d59f803fb 100644
@@ -5259,6 +5259,11 @@ static void build_zonelists(pg_data_t *pgdat)
 
Quoted 10 lines

mm/page_alloc.c static void build_zonelists(pg_data_t *pgdat) · line 5267

Quoted 8 lines
mm/page_alloc.c +5 -0
 	build_zonelists_in_node_order(pgdat, node_order, nr_nodes);
 	build_thisnode_zonelists(pgdat);
+
+	pr_info("node[%d] zonelist: ", pgdat->node_id);
+	for_each_zone_zonelist(zone, z, &pgdat->node_zonelists[ZONELIST_FALLBACK], MAX_NR_ZONES-1)
+		pr_cont("%d:%s ", zone_to_nid(zone), zone->name);
+	pr_cont("\n");
 }

Looks like this patch fell through the cracks - any update on this?

I was waiting for some feedback. As there were no complains about the above debugging output I will make it a separate patch and post both patches later this week. I just have to go through my backlog pile after vacation.

Signature · 2 lines
Michal Hocko
SUSE Labs