Enable fastboot support for Poplar board
cover Enable fastboot support for Poplar board
It enables DWC2 OTG gadget driver and fastboot support for Poplar board.
Shawn Guo (2):
poplar: add DWC2 OTG gadget support
poplar_defconfig: enable fastboot support
.../asm/arch-hi3798cv200/hi3798cv200.h | 5 ++++ board/hisilicon/poplar/poplar.c | 28 +++++++++++++++++++ configs/poplar_defconfig | 14 ++++++++++ 3 files changed, 47 insertions(+)
Signature · 1 line
2.18.0
PATCH 1/2 poplar: add DWC2 OTG gadget support
It enables DWC2 OTG gadget driver support for Poplar board. As usb2_phy_init() is being always called from board_init(), we can save the call from board_usb_init().
--- .../asm/arch-hi3798cv200/hi3798cv200.h | 5 ++++ board/hisilicon/poplar/poplar.c | 28 +++++++++++++++++++ 2 files changed, 33 insertions(+)
arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h +5 -0
@@ -13,11 +13,16 @@/* DEVICES */ #define REG_BASE_MCI 0xF9830000#define REG_BASE_UART0 0xF8B00000 +#define HIOTG_BASE_ADDR 0xF98C0000/* PERI control registers (4KB) */ /* USB2 PHY01 configuration register */ #define PERI_CTRL_USB0 (REG_BASE_PERI_CTRL + 0x120) +/* USB2 controller configuration register */ +#define PERI_CTRL_USB3 (REG_BASE_PERI_CTRL + 0x12c) +#define USB2_2P_CHIPID (1 << 28) +/* PERI CRG registers (4KB) */ /* USB2 CTRL0 clock and soft reset */ #define PERI_CRG46 (REG_BASE_CRG + 0xb8)
board/hisilicon/poplar/poplar.c +28 -0
@@ -168,6 +168,34 @@ int board_mmc_init(bd_t *bis) }#endif +#if defined(CONFIG_USB_GADGET ) && defined(CONFIG_USB_GADGET_DWC2_OTG ) +#include <usb.h> +#include <usb/dwc2_udc.h> +#include <g_dnl.h> + +static struct dwc2_plat_otg_data poplar_otg_data = { + .regs_otg =HIOTG_BASE_ADDR +}; + +static void set_usb_to_device (void ) +{ +setbits_le32 (PERI_CTRL_USB3 ,USB2_2P_CHIPID ); +} + +int board_usb_init (int index,enum usb_init_type init) +{ +set_usb_to_device (); +return dwc2_udc_probe (&poplar_otg_data); +} + +int g_dnl_bind_fixup (struct usb_device_descriptor *dev,const char *name) +{ +if (!env_get ("serial#" )) +g_dnl_set_serialnumber ("0123456789POPLAR" ); +return 0 ; +} +#endif +int board_init (void ) {usb2_phy_init ();
Signature · 1 line
2.18.0
PATCH 1/2 poplar: add DWC2 OTG gadget support
Quoted 5 lines · Shawn Guo
It enables DWC2 OTG gadget driver support for Poplar board. As
usb2_phy_init()is being always called fromboard_init(), we can save the call fromboard_usb_init().Signed-off-by Shawn Guo <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190115/6501cf8f/attachment.sig>
PATCH 2/2 poplar_defconfig: enable fastboot support
In reply to Shawn GuoIt enables fastboot support on Poplar board by using DWC2 OTG gadget driver.
--- configs/poplar_defconfig | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
configs/poplar_defconfig +14 -0
@@ -6,6 +6,13 @@ CONFIG_DISTRO_DEFAULTS=y CONFIG_NR_DRAM_BANKS=2 # CONFIG_DISPLAY_CPUINFO is not set CONFIG_SYS_PROMPT="poplar# " +CONFIG_FASTBOOT=y +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_CMD_FASTBOOT=y +CONFIG_FASTBOOT_BUF_ADDR=0x20000000 +CONFIG_FASTBOOT_BUF_SIZE=0x10000000 +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=0 CONFIG_CMD_MMC=y CONFIG_CMD_USB=y # CONFIG_ISO_PARTITION is not set
@@ -18,6 +25,13 @@ CONFIG_USB=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y CONFIG_USB_STORAGE=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_DWC2_OTG=y +CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_USB_GADGET_MANUFACTURER="HiSilicon" +CONFIG_USB_GADGET_VENDOR_NUM=0x18d1 +CONFIG_USB_GADGET_PRODUCT_NUM=0xd00d CONFIG_USB_HOST_ETHER=y CONFIG_USB_ETHER_ASIX=y CONFIG_FAT_WRITE=y
Signature · 1 line
2.18.0
PATCH 2/2 poplar_defconfig: enable fastboot support
Quoted 4 lines · Shawn Guo
It enables fastboot support on Poplar board by using DWC2 OTG gadget driver.
Signed-off-by Shawn Guo <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190115/f647f65e/attachment.sig>
cover Enable fastboot support for Poplar board
In reply to Shawn GuoQuoted 6 lines · Shawn Guo
It enables DWC2 OTG gadget driver and fastboot support for Poplar board.
Shawn Guo (2):
poplar: add DWC2 OTG gadget support
poplar_defconfig: enable fastboot support
Hi Tom,
Are you okay with these two patches?
Shawn
cover Enable fastboot support for Poplar board
Quoted 11 lines · Shawn Guo
Quoted 6 lines · Shawn Guo
It enables DWC2 OTG gadget driver and fastboot support for Poplar board.
Shawn Guo (2):
poplar: add DWC2 OTG gadget support
poplar_defconfig: enable fastboot supportHi Tom,
Are you okay with these two patches?
Yes, but I'll pick them up once the merge window opens again.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190114/df2f8a39/attachment.sig>