Skip to contentSkip to conversation

mfd: lochnagar: Add initial binding documentation

PATCH Superseded Charles Keepax 2 participants 8 messages Jan 17, 2019 – Jan 29, 2019

Subsystems (6)

v6 of 8 Superseded Latest is v8 →

lore
Share & tools
lore

Charles Keepax

author maintainer
#0 lore raw

PATCH v6 1/6 mfd: lochnagar: Add initial binding documentation

Lochnagar is an evaluation and development board for Cirrus Logic Smart CODEC and Amp devices. It allows the connection of most Cirrus Logic devices on mini-cards, as well as allowing connection of various application processor systems to provide a full evaluation platform. This driver supports the board controller chip on the Lochnagar board.

---

Apologies for the slight delay in getting v6 out been very busy lately but hopefully we should just about be here with this version.

No changes since v5.

Thanks,
Charles

 .../devicetree/bindings/mfd/cirrus,lochnagar.txt   |  71 +++++++++++
 include/dt-bindings/clk/lochnagar.h                |  26 ++++
 include/dt-bindings/pinctrl/lochnagar.h            | 132 +++++++++++++++++++++
 3 files changed, 229 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt
 create mode 100644 include/dt-bindings/clk/lochnagar.h
 create mode 100644 include/dt-bindings/pinctrl/lochnagar.h
Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt new file +71 -0
new file mode 100644
index 000000000000..7a5f99fb489d
@@ -0,0 +1,71 @@
+Cirrus Logic Lochnagar Audio Development Board
+
+Lochnagar is an evaluation and development board for Cirrus Logic
+Smart CODEC and Amp devices. It allows the connection of most Cirrus
+Logic devices on mini-cards, as well as allowing connection of
+various application processor systems to provide a full evaluation
+platform.  Audio system topology, clocking and power can all be
+controlled through the Lochnagar, allowing the device under test
+to be used in a variety of possible use cases.
+
+Also see these documents for generic binding information:
+  [1] GPIO : ../gpio/gpio.txt
+
+And these for relevant defines:
+  [2] include/dt-bindings/pinctrl/lochnagar.h
+  [3] include/dt-bindings/clock/lochnagar.h
+
+And these documents for the required sub-node binding details:
+  [4] Clock: ../clock/cirrus,lochnagar.txt
+  [5] Pinctrl: ../pinctrl/cirrus,lochnagar.txt
+  [6] Regulator: ../regulator/cirrus,lochnagar.txt
+
+Required properties:
+
+  - compatible : One of the following strings:
+                 "cirrus,lochnagar1"
+                 "cirrus,lochnagar2"
+
+  - reg : I2C slave address
+
+  - reset-gpios : Reset line to the Lochnagar, see [1].
+
+Required sub-nodes:
+
+  - lochnagar-clk : Binding for the clocking components, see [4].
+
+  - lochnagar-pinctrl : Binding for the pin control components, see [5].
+
+  - lochnagar-regulator : Binding for the regulator components, see [6].
+                          Only required for Lochnagar 2.
+
+Optional properties:
+
+  - present-gpios : Host present line, indicating the presence of a
+    host system, see [1]. This can be omitted if the present line is
+    tied in hardware.
+
+Example:
+
+lochnagar: lochnagar@22 {
+	compatible = "cirrus,lochnagar2";
+	reg = <0x22>;
+
+	reset-gpios = <&gpio0 55 0>;
+	present-gpios = <&gpio0 60 0>;
+
+	lochnagar-clk {
+		compatible = "cirrus,lochnagar2-clk";
+		...
+	};
+
+	lochnagar-pinctrl {
+		compatible = "cirrus,lochnagar-pinctrl";
+		...
+	};
+
+	lochnagar-regulator {
+		compatible = "cirrus,lochnagar-regulator";
+		...
+	};
+};
include/dt-bindings/clk/lochnagar.h new file +26 -0
new file mode 100644
index 000000000000..8fa20551ff17
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Device Tree defines for Lochnagar clocking
+ *
+ * Copyright (c) 2017-2018 Cirrus Logic, Inc. and
+ *                         Cirrus Logic International Semiconductor Ltd.
+ *
+ * Author: Charles Keepax <[email protected]>
+ */
+
+#ifndef DT_BINDINGS_CLK_LOCHNAGAR_H
+#define DT_BINDINGS_CLK_LOCHNAGAR_H
+
+#define LOCHNAGAR_CDC_MCLK1		0
+#define LOCHNAGAR_CDC_MCLK2		1
+#define LOCHNAGAR_DSP_CLKIN		2
+#define LOCHNAGAR_GF_CLKOUT1		3
+#define LOCHNAGAR_GF_CLKOUT2		4
+#define LOCHNAGAR_PSIA1_MCLK		5
+#define LOCHNAGAR_PSIA2_MCLK		6
+#define LOCHNAGAR_SPDIF_MCLK		7
+#define LOCHNAGAR_ADAT_MCLK		8
+#define LOCHNAGAR_SOUNDCARD_MCLK	9
+#define LOCHNAGAR_SPDIF_CLKOUT		10
+
+#endif
include/dt-bindings/pinctrl/lochnagar.h new file +132 -0

132 lines not on this page · raw message

Signature · 1 line
2.11.0
author maintainer
#1 lore raw

PATCH v6 2/6 clk: lochnagar: Add initial binding documentation

Lochnagar is an evaluation and development board for Cirrus Logic Smart CODEC and Amp devices. It allows the connection of most Cirrus Logic devices on mini-cards, as well as allowing connection of various application processor systems to provide a full evaluation platform. This driver supports the board controller chip on the Lochnagar board.

---

Changes since v5:
- Add missing 8m fixed clock

Thanks,
Charles

 .../devicetree/bindings/clock/cirrus,lochnagar.txt | 93 ++++++++++++++++++++++
 1 file changed, 93 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt
Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt new file +93 -0
new file mode 100644
index 000000000000..b8d8ef3bdc5f
@@ -0,0 +1,93 @@
+Cirrus Logic Lochnagar Audio Development Board
+
+Lochnagar is an evaluation and development board for Cirrus Logic
+Smart CODEC and Amp devices. It allows the connection of most Cirrus
+Logic devices on mini-cards, as well as allowing connection of
+various application processor systems to provide a full evaluation
+platform.  Audio system topology, clocking and power can all be
+controlled through the Lochnagar, allowing the device under test
+to be used in a variety of possible use cases.
+
+This binding document describes the binding for the clock portion of
+the driver.
+
+Also see these documents for generic binding information:
+  [1] Clock : ../clock/clock-bindings.txt
+
+And these for relevant defines:
+  [2] include/dt-bindings/clock/lochnagar.h
+
+This binding must be part of the Lochnagar MFD binding:
+  [3] ../mfd/cirrus,lochnagar.txt
+
+Required properties:
+
+  - compatible : One of the following strings:
+                 "cirrus,lochnagar1-clk"
+                 "cirrus,lochnagar2-clk"
+
+  - #clock-cells : Must be 1. The first cell indicates the clock
+    number, see [2] for available clocks and [1].
+
+Optional properties:
+
+  - clocks : Must contain an entry for each clock in clock-names.
+  - clock-names : May contain entries for each of the following
+    clocks:
+     - ln-cdc-clkout : Output clock from CODEC card.
+     - ln-dsp-clkout : Output clock from DSP card.
+     - ln-gf-mclk1,ln-gf-mclk2,ln-gf-mclk3,ln-gf-mclk4 : Optional
+       input audio clocks from host system.
+     - ln-psia1-mclk, ln-psia2-mclk : Optional input audio clocks from
+       external connector.
+     - ln-spdif-clkout : Optional input audio clock from SPDIF.
+     - ln-adat-mclk : Optional input audio clock from ADAT.
+     - ln-pmic-32k : On board fixed clock.
+     - ln-clk-12m : On board fixed clock.
+     - ln-clk-11m : On board fixed clock.
+     - ln-clk-24m : On board fixed clock.
+     - ln-clk-22m : On board fixed clock.
+     - ln-clk-8m : On board fixed clock.
+     - ln-usb-clk-24m : On board fixed clock.
+     - ln-usb-clk-12m : On board fixed clock.
+
+  - assigned-clocks : A list of Lochnagar clocks to be reparented, see
+    [2] for available clocks.
+  - assigned-clock-parents : Parents to be assigned to the clocks
+    listed in "assigned-clocks".
+
+Optional nodes:
+
+  - fixed-clock nodes may be registered for the following on board clocks:
+     - ln-pmic-32k : 32768 Hz
+     - ln-clk-12m : 12288000 Hz
+     - ln-clk-11m : 11298600 Hz
+     - ln-clk-24m : 24576000 Hz
+     - ln-clk-22m : 22579200 Hz
+     - ln-clk-8m : 8192000 Hz
+     - ln-usb-clk-24m : 24576000 Hz
+     - ln-usb-clk-12m : 12288000 Hz
+
+Example:
+
+lochnagar {
+	lochnagar-clk {
+		compatible = "cirrus,lochnagar2-clk";
+
+		#clock-cells = <1>;
+
+		clocks = <&clk-audio>, <&clk_pmic>;
+		clock-names = "ln-gf-mclk2", "ln-pmic-32k";
+
+		assigned-clocks = <&lochnagar-clk LOCHNAGAR_CDC_MCLK1>,
+				  <&lochnagar-clk LOCHNAGAR_CDC_MCLK2>;
+		assigned-clock-parents = <&clk-audio>,
+					 <&clk-pmic>;
+	};
+
+	clk-pmic: clk-pmic {
+		compatible = "fixed-clock";
+		clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+};
Signature · 1 line
2.11.0
maintainer Reviewed-by on v6 2/6
#2 lore raw

Re: [PATCH v6 2/6] clk: lochnagar: Add initial binding documentation

Quoted 13 lines · Charles Keepax

Lochnagar is an evaluation and development board for Cirrus Logic Smart CODEC and Amp devices. It allows the connection of most Cirrus Logic devices on mini-cards, as well as allowing connection of various application processor systems to provide a full evaluation platform. This driver supports the board controller chip on the Lochnagar board.

---

Changes since v5:
- Add missing 8m fixed clock

Quoted 7 lines

Thanks,
Charles

 .../devicetree/bindings/clock/cirrus,lochnagar.txt | 93 ++++++++++++++++++++++
 1 file changed, 93 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt
author maintainer
#3 lore raw

PATCH v6 3/6 pinctrl: lochnagar: Add initial binding documentation

In reply to Charles Keepax

Lochnagar is an evaluation and development board for Cirrus Logic Smart CODEC and Amp devices. It allows the connection of most Cirrus Logic devices on mini-cards, as well as allowing connection of various application processor systems to provide a full evaluation platform. This driver supports the board controller chip on the Lochnagar board.

---

No changes since v5.

Thanks,
Charles

 .../bindings/pinctrl/cirrus,lochnagar.txt          | 141 +++++++++++++++++++++
 1 file changed, 141 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt
Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt new file +141 -0
new file mode 100644
index 000000000000..36de6b0555f2
@@ -0,0 +1,141 @@
+Cirrus Logic Lochnagar Audio Development Board
+
+Lochnagar is an evaluation and development board for Cirrus Logic
+Smart CODEC and Amp devices. It allows the connection of most Cirrus
+Logic devices on mini-cards, as well as allowing connection of
+various application processor systems to provide a full evaluation
+platform.  Audio system topology, clocking and power can all be
+controlled through the Lochnagar, allowing the device under test
+to be used in a variety of possible use cases.
+
+This binding document describes the binding for the pinctrl portion
+of the driver.
+
+Also see these documents for generic binding information:
+  [1] GPIO : ../gpio/gpio.txt
+  [2] Pinctrl: ../pinctrl/pinctrl-bindings.txt
+
+And these for relevant defines:
+  [3] include/dt-bindings/pinctrl/lochnagar.h
+
+This binding must be part of the Lochnagar MFD binding:
+  [4] ../mfd/cirrus,lochnagar.txt
+
+Required properties:
+
+  - compatible : One of the following strings:
+                 "cirrus,lochnagar-pinctrl"
+
+  - gpio-controller : Indicates this device is a GPIO controller.
+  - #gpio-cells : Must be 2. The first cell is the pin number, see
+    [3] for available pins and the second cell is used to specify
+    optional parameters, see [1].
+  - gpio-ranges : Range of pins managed by the GPIO controller, see
+    [1]. Both the GPIO and Pinctrl base should be set to zero and the
+    count to the appropriate of the LOCHNAGARx_PIN_NUM_GPIOS define,
+    see [3].
+
+  - pinctrl-names : A pinctrl state named "default" must be defined.
+  - pinctrl-0 : A phandle to the default pinctrl state.
+
+Required sub-nodes:
+
+The pin configurations are defined as a child of the pinctrl states
+node, see [2]. Each sub-node can have the following properties:
+  - groups : A list of groups to select (either this or "pins" must be
+    specified), available groups:
+      codec-aif1, codec-aif2, codec-aif3, dsp-aif1, dsp-aif2, psia1,
+      psia2, gf-aif1, gf-aif2, gf-aif3, gf-aif4, spdif-aif, usb-aif1,
+      usb-aif2, adat-aif, soundcard-aif
+  - pins : A list of pin names to select (either this or "groups" must
+    be specified), available pins:
+      fgpa-gpio1, fgpa-gpio2, fgpa-gpio3, fgpa-gpio4, fgpa-gpio5,
+      fgpa-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4,
+      codec-gpio5, codec-gpio6, codec-gpio7, codec-gpio8, dsp-gpio1,
+      dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2,
+      gf-gpio3, gf-gpio7, codec-aif1-bclk, codec-aif1-rxdat,
+      codec-aif1-lrclk, codec-aif1-txdat, codec-aif2-bclk,
+      codec-aif2-rxdat, codec-aif2-lrclk, codec-aif2-txdat,
+      codec-aif3-bclk, codec-aif3-rxdat, codec-aif3-lrclk,
+      codec-aif3-txdat, dsp-aif1-bclk, dsp-aif1-rxdat, dsp-aif1-lrclk,
+      dsp-aif1-txdat, dsp-aif2-bclk, dsp-aif2-rxdat,
+      dsp-aif2-lrclk, dsp-aif2-txdat, psia1-bclk, psia1-rxdat,
+      psia1-lrclk, psia1-txdat, psia2-bclk, psia2-rxdat, psia2-lrclk,
+      psia2-txdat, gf-aif3-bclk, gf-aif3-rxdat, gf-aif3-lrclk,
+      gf-aif3-txdat, gf-aif4-bclk, gf-aif4-rxdat, gf-aif4-lrclk,
+      gf-aif4-txdat, gf-aif1-bclk, gf-aif1-rxdat, gf-aif1-lrclk,
+      gf-aif1-txdat, gf-aif2-bclk, gf-aif2-rxdat, gf-aif2-lrclk,
+      gf-aif2-txdat, dsp-uart1-rx, dsp-uart1-tx, dsp-uart2-rx,
+      dsp-uart2-tx, gf-uart2-rx, gf-uart2-tx, usb-uart-rx,
+      codec-pdmclk1, codec-pdmdat1, codec-pdmclk2, codec-pdmdat2,
+      codec-dmicclk1, codec-dmicdat1, codec-dmicclk2, codec-dmicdat2,
+      codec-dmicclk3, codec-dmicdat3, codec-dmicclk4, codec-dmicdat4,
+      dsp-dmicclk1, dsp-dmicdat1, dsp-dmicclk2, dsp-dmicdat2, i2c2-scl,
+      i2c2-sda, i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda, dsp-standby,
+      codec-mclk1, codec-mclk2, dsp-clkin, psia1-mclk, psia2-mclk,
+      gf-gpio1, gf-gpio5, dsp-gpio20, led1, led2
+  - function : The mux function to select, available functions:
+      aif, fgpa-gpio1, fgpa-gpio2, fgpa-gpio3, fgpa-gpio4, fgpa-gpio5,
+      fgpa-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4,
+      codec-gpio5, codec-gpio6, codec-gpio7, codec-gpio8, dsp-gpio1,
+      dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2,
+      gf-gpio3, gf-gpio7, gf-gpio1, gf-gpio5, dsp-gpio20, codec-clkout,
+      dsp-clkout, pmic-32k, spdif-clkout, clk-12m288, clk-11m2986,
+      clk-24m576, clk-22m5792, xmos-mclk, gf-clkout1, gf-mclk1,
+      gf-mclk3, gf-mclk2, gf-clkout2, codec-mclk1, codec-mclk2,
+      dsp-clkin, psia1-mclk, psia2-mclk, spdif-mclk, codec-irq,
+      codec-reset, dsp-reset, dsp-irq, dsp-standby, codec-pdmclk1,
+      codec-pdmdat1, codec-pdmclk2, codec-pdmdat2, codec-dmicclk1,
+      codec-dmicdat1, codec-dmicclk2, codec-dmicdat2, codec-dmicclk3,
+      codec-dmicdat3, codec-dmicclk4, codec-dmicdat4, dsp-dmicclk1,
+      dsp-dmicdat1, dsp-dmicclk2, dsp-dmicdat2, dsp-uart1-rx,
+      dsp-uart1-tx, dsp-uart2-rx, dsp-uart2-tx, gf-uart2-rx,
+      gf-uart2-tx, usb-uart-rx, usb-uart-tx, i2c2-scl, i2c2-sda,
+      i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda, gpio, spdif-aif, psia1,
+      psia1-bclk, psia1-lrclk, psia1-rxdat, psia1-txdat, psia2,
+      psia2-bclk, psia2-lrclk, psia2-rxdat, psia2-txdat, codec-aif1,
+      codec-aif1-bclk, codec-aif1-lrclk, codec-aif1-rxdat,
+      codec-aif1-txdat, codec-aif2, codec-aif2-bclk, codec-aif2-lrclk,
+      codec-aif2-rxdat, codec-aif2-txdat, codec-aif3, codec-aif3-bclk,
+      codec-aif3-lrclk, codec-aif3-rxdat, codec-aif3-txdat, dsp-aif1,
+      dsp-aif1-bclk, dsp-aif1-lrclk, dsp-aif1-rxdat, dsp-aif1-txdat,
+      dsp-aif2, dsp-aif2-bclk, dsp-aif2-lrclk, dsp-aif2-rxdat,
+      dsp-aif2-txdat, gf-aif3, gf-aif3-bclk, gf-aif3-lrclk,
+      gf-aif3-rxdat, gf-aif3-txdat, gf-aif4, gf-aif4-bclk,
+      gf-aif4-lrclk, gf-aif4-rxdat, gf-aif4-txdat, gf-aif1,
+      gf-aif1-bclk, gf-aif1-lrclk, gf-aif1-rxdat, gf-aif1-txdat,
+      gf-aif2, gf-aif2-bclk, gf-aif2-lrclk, gf-aif2-rxdat,
+      gf-aif2-txdat, usb-aif1, usb-aif2, adat-aif, soundcard-aif,
+
+  - output-enable : Specifies that an AIF group will be used as a master
+    interface (either this or input-enable is required if a group is
+    being muxed to an AIF)
+  - input-enable : Specifies that an AIF group will be used as a slave
+    interface (either this or output-enable is required if a group is
+    being muxed to an AIF)
+
+Example:
+
+lochnagar-pinctrl {
+	compatible = "cirrus,lochnagar-pinctrl";
+
+	gpio-controller;
+	#gpio-cells = <2>;
+	gpio-ranges = <&lochnagar 0 0 LOCHNAGAR2_PIN_NUM_GPIOS>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pin-settings>;
+
+	pin-settings: pin-settings {
+		ap-aif {
+			input-enable;
+			groups = "gf-aif1";
+			function = "codec-aif3";
+		};
+		codec-aif {
+			output-enable;
+			groups = "codec-aif3";
+			function = "gf-aif1";
+		};
+	};
+};
Signature · 1 line
2.11.0
author maintainer
#4 lore raw

PATCH v6 4/6 mfd: lochnagar: Add support for the Cirrus Logic Lochnagar

In reply to Charles Keepax

Lochnagar is an evaluation and development board for Cirrus Logic Smart CODEC and Amp devices. It allows the connection of most Cirrus Logic devices on mini-cards, as well as allowing connection of various application processor systems to provide a full evaluation platform. This driver supports the board controller chip on the Lochnagar board. Audio system topology, clocking and power can all be controlled through the Lochnagar controller chip, allowing the device under test to be used in a variety of possible use cases.

As the Lochnagar is a fairly complex device this MFD driver allows the drivers for the various features to be bound in. Initially clocking, regulator and pinctrl will be added as these are necessary to configure the system. But in time at least audio and voltage/current monitoring will also be added.

---

Changes since v5:
- Remove CLK_DIR register bits as they are no longer used

Thanks,
Charles

 MAINTAINERS                         |  17 ++
 drivers/mfd/Kconfig                 |   8 +
 drivers/mfd/Makefile                |   2 +
 drivers/mfd/lochnagar-i2c.c         | 394 ++++++++++++++++++++++++++++++++++++
 include/linux/mfd/lochnagar.h       |  55 +++++
 include/linux/mfd/lochnagar1_regs.h | 157 ++++++++++++++
 include/linux/mfd/lochnagar2_regs.h | 251 +++++++++++++++++++++++
 7 files changed, 884 insertions(+)
 create mode 100644 drivers/mfd/lochnagar-i2c.c
 create mode 100644 include/linux/mfd/lochnagar.h
 create mode 100644 include/linux/mfd/lochnagar1_regs.h
 create mode 100644 include/linux/mfd/lochnagar2_regs.h
MAINTAINERS +17 -0
index 4d04cebb4a71..23577911b3e9 100644
@@ -3701,6 +3701,23 @@ L:	[email protected]
 S:	Maintained
 F:	drivers/net/ethernet/cirrus/ep93xx_eth.c
 
+CIRRUS LOGIC LOCHNAGAR DRIVER
+M:	Charles Keepax <[email protected]>
+M:	Richard Fitzgerald <[email protected]>
+L:	[email protected]
+S:	Supported
+F:	drivers/clk/clk-lochnagar.c
+F:	drivers/mfd/lochnagar-i2c.c
+F:	drivers/pinctrl/cirrus/pinctrl-lochnagar.c
+F:	drivers/regulator/lochnagar-regulator.c
+F:	include/dt-bindings/clk/lochnagar.h
+F:	include/dt-bindings/pinctrl/lochnagar.h
+F:	include/linux/mfd/lochnagar*
+F:	Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt
+F:	Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt
+F:	Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt
+F:	Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt
+
 CISCO FCOE HBA DRIVER
 M:	Satish Kharat <[email protected]>
 M:	Sesidhar Baddela <[email protected]>
drivers/mfd/Kconfig +8 -0
index f461460a2aeb..f68ce6f38ceb 100644
@@ -1686,6 +1686,14 @@ config MFD_VX855
 	  VIA VX855/VX875 south bridge. You will need to enable the vx855_spi
 	  and/or vx855_gpio drivers for this to do anything useful.
 
+config MFD_LOCHNAGAR
+	bool "Cirrus Logic Lochnagar Audio Development Board"
+	select MFD_CORE
+	select REGMAP_I2C
+	depends on I2C=y && OF
+	help
+	  Support for Cirrus Logic Lochnagar audio development board.
+
 config MFD_ARIZONA
 	select REGMAP
 	select REGMAP_IRQ
drivers/mfd/Makefile +2 -0
index 12980a4ad460..93284316d530 100644
@@ -37,6 +37,8 @@ obj-$(CONFIG_MFD_T7L66XB)	+= t7l66xb.o tmio_core.o
 obj-$(CONFIG_MFD_TC6387XB)	+= tc6387xb.o tmio_core.o
 obj-$(CONFIG_MFD_TC6393XB)	+= tc6393xb.o tmio_core.o
 
+obj-$(CONFIG_MFD_LOCHNAGAR)	+= lochnagar-i2c.o
+
 obj-$(CONFIG_MFD_ARIZONA)	+= arizona-core.o
 obj-$(CONFIG_MFD_ARIZONA)	+= arizona-irq.o
 obj-$(CONFIG_MFD_ARIZONA_I2C)	+= arizona-i2c.o
drivers/mfd/lochnagar-i2c.c new file +394 -0

394 lines not on this page · raw message

include/linux/mfd/lochnagar.h new file +55 -0

55 lines not on this page · raw message

include/linux/mfd/lochnagar1_regs.h new file +157 -0

157 lines not on this page · raw message

include/linux/mfd/lochnagar2_regs.h new file +251 -0

251 lines not on this page · raw message

Signature · 1 line
2.11.0
author maintainer
#5 lore raw

PATCH v6 5/6 clk: lochnagar: Add support for the Cirrus Logic Lochnagar

In reply to Charles Keepax

Lochnagar is an evaluation and development board for Cirrus Logic Smart CODEC and Amp devices. It allows the connection of most Cirrus Logic devices on mini-cards, as well as allowing connection of various application processor systems to provide a full evaluation platform. This driver supports the board controller chip on the Lochnagar board.

The Lochnagar can take several input clocks from the host system, provides several of its own clock sources, and provides extensive routing options for those clocks to be supplied to the attached CODEC/Amp device.

---

Changes since v5:
- Remove unnecessary direction bit handling
- Add missing 8m clock
- Rename clock functions to remove regmap from the name
- Change some error messages to debugs
- No longer use of_clk_hw_onecell_get
- Add missing MODULE_DEVICE_TABLE
- Remove redundant MODULE_ALIAS and of_match_ptr

Thanks,
Charles

 drivers/clk/Kconfig         |   7 +
 drivers/clk/Makefile        |   1 +
 drivers/clk/clk-lochnagar.c | 340 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 348 insertions(+)
 create mode 100644 drivers/clk/clk-lochnagar.c
drivers/clk/Kconfig +7 -0
index e5b2fe80eab4..a5cb8f923674 100644
@@ -219,6 +219,13 @@ config COMMON_CLK_XGENE
 	---help---
 	  Sypport for the APM X-Gene SoC reference, PLL, and device clocks.
 
+config COMMON_CLK_LOCHNAGAR
+	tristate "Cirrus Logic Lochnagar clock driver"
+	depends on MFD_LOCHNAGAR
+	help
+	  This driver supports the clocking features of the Cirrus Logic
+	  Lochnagar audio development board.
+
 config COMMON_CLK_NXP
 	def_bool COMMON_CLK && (ARCH_LPC18XX || ARCH_LPC32XX)
 	select REGMAP_MMIO if ARCH_LPC32XX
drivers/clk/Makefile +1 -0
index 8a9440a97500..7101d3da5efd 100644
@@ -31,6 +31,7 @@ obj-$(CONFIG_COMMON_CLK_GEMINI)		+= clk-gemini.o
 obj-$(CONFIG_COMMON_CLK_ASPEED)		+= clk-aspeed.o
 obj-$(CONFIG_ARCH_HIGHBANK)		+= clk-highbank.o
 obj-$(CONFIG_CLK_HSDK)			+= clk-hsdk-pll.o
+obj-$(CONFIG_COMMON_CLK_LOCHNAGAR)	+= clk-lochnagar.o
 obj-$(CONFIG_COMMON_CLK_MAX77686)	+= clk-max77686.o
 obj-$(CONFIG_COMMON_CLK_MAX9485)	+= clk-max9485.o
 obj-$(CONFIG_ARCH_MOXART)		+= clk-moxart.o
drivers/clk/clk-lochnagar.c new file +340 -0

340 lines not on this page · raw message

Signature · 1 line
2.11.0
author maintainer
#6 lore raw

PATCH v6 6/6 pinctrl: lochnagar: Add support for the Cirrus Logic Lochnagar

In reply to Charles Keepax

Lochnagar is an evaluation and development board for Cirrus Logic Smart CODEC and Amp devices. It allows the connection of most Cirrus Logic devices on mini-cards, as well as allowing connection of various application processor systems to provide a full evaluation platform. This driver supports the board controller chip on the Lochnagar board.

Lochnagar provides many pins which can generally be used for an audio function such as an AIF or a PDM interface, but also as GPIOs.

---

Changes since v5:
- Add MODULE_DEVICE_TABLE and remove redundant MODULE_ALIAS

Thanks,
Charles

 drivers/pinctrl/cirrus/Kconfig             |   10 +
 drivers/pinctrl/cirrus/Makefile            |    2 +
 drivers/pinctrl/cirrus/pinctrl-lochnagar.c | 1236 ++++++++++++++++++++++++++++
 3 files changed, 1248 insertions(+)
 create mode 100644 drivers/pinctrl/cirrus/pinctrl-lochnagar.c
drivers/pinctrl/cirrus/Kconfig +10 -0
index 27013e5949bc..74af07e25174 100644
@@ -1,3 +1,13 @@
+config PINCTRL_LOCHNAGAR
+	tristate "Cirrus Logic Lochnagar pinctrl driver"
+	depends on MFD_LOCHNAGAR
+	select PINMUX
+	select PINCONF
+	select GENERIC_PINCONF
+	help
+	  This driver supports configuring the GPIO and other pin configuration
+	  of the Cirrus Logic Lochnagar audio development board.
+
 # This is all selected by the Madera MFD driver Kconfig options
 config PINCTRL_MADERA
 	tristate
drivers/pinctrl/cirrus/Makefile +2 -0
index 6e4938cde9e3..20baebf438f6 100644
@@ -1,4 +1,6 @@
 # Cirrus Logic pinctrl drivers
+obj-$(CONFIG_PINCTRL_LOCHNAGAR)	+= pinctrl-lochnagar.o
+
 pinctrl-madera-objs		:= pinctrl-madera-core.o
 ifeq ($(CONFIG_PINCTRL_CS47L35),y)
 pinctrl-madera-objs		+= pinctrl-cs47l35.o
drivers/pinctrl/cirrus/pinctrl-lochnagar.c new file +1236 -0

1,236 lines not on this page · raw message

Signature · 1 line
2.11.0
author maintainer
#7 lore raw
In reply to Charles Keepax
Quoted 12 lines · Charles Keepax
Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt new file +12 -0
+Example:
+
+lochnagar: lochnagar@22 {
+	compatible = "cirrus,lochnagar2";
+	reg = <0x22>;
+
+	reset-gpios = <&gpio0 55 0>;
+	present-gpios = <&gpio0 60 0>;
+
+	lochnagar-clk {
+		compatible = "cirrus,lochnagar2-clk";
+		...

Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt line 69

Quoted 10 lines
Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt new file +10 -0
+	};
+
+	lochnagar-pinctrl {
+		compatible = "cirrus,lochnagar-pinctrl";
+		...
+	};
+
+	lochnagar-regulator {
+		compatible = "cirrus,lochnagar-regulator";
+		...

Sorry just realised this entry in the example is a hang over from earlier versions of the regulator code and needs to go apologies I will respin the series.

Thanks,
Charles