media/sun6i: Allwinner A64 CSI support
Subsystems (4)
v6 cover media/sun6i: Allwinner A64 CSI support
This is v6 set for previous version[1] series to support CSI on Allwinner A64.
Tested 640x480, 320x240, 720p, 1080p resolutions UYVY8_2X8 format.
Changes for v6:
- set the mod rate in seett_power instead of probe Changes for v5:
- Add mod_rate quirk for better handling clk_set code Changes for v4:
- update the compatible string order
- add proper commit message
- included BPI-M64 patch
- skipped amarula-a64 patch
Changes for v3:
- update dt-bindings for A64
- set mod clock via csi driver
- remove assign clocks from dtsi
- remove i2c-gpio opendrian
- fix avdd and dovdd supplies
- remove vcc-csi pin group supply
[1] https://patchwork.kernel.org/cover/10738841/
Jagan Teki (6):
dt-bindings: media: sun6i: Add A64 CSI compatible
media: sun6i: Add mod_rate quirk
media: sun6i: Add A64 CSI block support
arm64: dts: allwinner: a64: Add A64 CSI controller
arm64: dts: allwinner: a64: Add pinmux setting for CSI MCLK on PE1 [DO NOT MERGE] arm64: dts: allwinner: bananapi-m64: Add HDF5640 camera module
.../devicetree/bindings/media/sun6i-csi.txt | 1 + .../dts/allwinner/sun50i-a64-bananapi-m64.dts | 65 +++++++++++++++++++ arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 25 +++++++ .../platform/sunxi/sun6i-csi/sun6i_csi.c | 31 +++++++-- 4 files changed, 118 insertions(+), 4 deletions(-)
Signature · 1 line
2.18.0.321.gffc6fa0e3
PATCH v6 1/6 dt-bindings: media: sun6i: Add A64 CSI compatible
Allwinner A64 CSI is a single channel time-multiplexed BT.656 protocol interface.
Add separate compatible string for A64 since it require explicit change in sun6i_csi driver to update default CSI_SCLK rate.
--- Documentation/devicetree/bindings/media/sun6i-csi.txt | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/media/sun6i-csi.txt +1 -0
@@ -8,6 +8,7 @@ Required properties: * "allwinner,sun6i-a31-csi" * "allwinner,sun8i-h3-csi" * "allwinner,sun8i-v3s-csi" + * "allwinner,sun50i-a64-csi" - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the CSI
Signature · 1 line
2.18.0.321.gffc6fa0e3
PATCH v6 2/6 media: sun6i: Add mod_rate quirk
In reply to Jagan TekiUnfortunately default CSI_SCLK rate cannot work properly to drive the connected sensor interface, particularly on few Allwinner SoC's like A64.
So, add mod_rate quirk via driver data so-that the respective SoC's which require to alter the default mod clock rate can assign the operating clock rate.
--- .../platform/sunxi/sun6i-csi/sun6i_csi.c | 26 ++++++++++++++++--- 1 file changed, 22 insertions(+), 4 deletions(-)
drivers/media/platform/sunxi/sun6i-csi/sun6i_csi.c +22 -4
@@ -15,6 +15,7 @@#include <linux/ioctl.h> #include <linux/module.h> #include <linux/of.h> +#include <linux/of_device.h> #include <linux/platform_device.h> #include <linux/pm_runtime.h> #include <linux/regmap.h>
@@ -28,8 +29,13 @@#define MODULE_NAME "sun6i-csi" +struct sun6i_csi_variant { +unsigned long mod_rate; +}; +struct sun6i_csi_dev {struct sun6i_csi csi; +const struct sun6i_csi_variant *variant;struct device *dev;struct regmap *regmap;
@@ -161,15 +167,20 @@ int sun6i_csi_set_power(struct sun6i_csi *csi, bool enable)regmap_update_bits (regmap,CSI_EN_REG ,CSI_EN_CSI_EN ,0 );clk_disable_unprepare (sdev->clk_ram); +if (sdev->variant->mod_rate) +clk_rate_exclusive_put (sdev->clk_mod);clk_disable_unprepare (sdev->clk_mod);reset_control_assert (sdev->rstc_bus);return 0 ; } +if (sdev->variant->mod_rate) +clk_set_rate_exclusive (sdev->clk_mod, sdev->variant->mod_rate); + ret =clk_prepare_enable (sdev->clk_mod);if (ret) {dev_err (sdev->dev,"Enable csi clk err %d\n" , ret); -return ret; + goto clk_mod_put; } ret =clk_prepare_enable (sdev->clk_ram);
@@ -192,6 +203,9 @@ int sun6i_csi_set_power(struct sun6i_csi *csi, bool enable)clk_disable_unprepare (sdev->clk_ram); clk_mod_disable:clk_disable_unprepare (sdev->clk_mod); +clk_mod_put: +if (sdev->variant->mod_rate) +clk_rate_exclusive_put (sdev->clk_mod);return ret; }
@@ -871,6 +885,7 @@ static int sun6i_csi_probe(struct platform_device *pdev) sdev->dev = &pdev->dev;/* The DMA bus has the memory mapped at 0 */ sdev->dev->dma_pfn_offset =PHYS_OFFSET >>PAGE_SHIFT ; + sdev->variant =of_device_get_match_data (sdev->dev); ret =sun6i_csi_resource_request (sdev, pdev);if (ret)
@@ -891,10 +906,13 @@ static int sun6i_csi_remove(struct platform_device *pdev)return 0 ; } +static const struct sun6i_csi_variant sun6i_a31_csi = { +}; +static const struct of_device_id sun6i_csi_of_match[] = { - { .compatible ="allwinner,sun6i-a31-csi" , }, - { .compatible ="allwinner,sun8i-h3-csi" , }, - { .compatible ="allwinner,sun8i-v3s-csi" , }, + { .compatible ="allwinner,sun6i-a31-csi" , .data = &sun6i_a31_csi, }, + { .compatible ="allwinner,sun8i-h3-csi" , .data = &sun6i_a31_csi, }, + { .compatible ="allwinner,sun8i-v3s-csi" , .data = &sun6i_a31_csi, }, {}, };MODULE_DEVICE_TABLE (of, sun6i_csi_of_match);
Signature · 1 line
2.18.0.321.gffc6fa0e3
Re: [PATCH v6 2/6] media: sun6i: Add mod_rate quirk
Quoted 9 lines · Jagan Teki
Unfortunately default
CSI_SCLKrate cannot work properly to drive the connected sensor interface, particularly on few Allwinner SoC's like A64.So, add
mod_ratequirk via driver data so-that the respective SoC's which require to alter the default mod clock rate can assign the operating clock rate.
You still don't need the variant stuff. If the sole difference is that we need that clock rate to be fixed, then the following patch is enough.
http://code.bulix.org/9au998-562745?raw
Maxime
Signature · 3 lines
Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
PATCH v6 3/6 media: sun6i: Add A64 CSI block support
In reply to Jagan TekiCSI block in Allwinner A64 has similar features as like in H3, but default mod clock rate in BSP along with latest mainline testing require to operate it at 300MHz.
So, add A64 CSI compatibe along with mod_rate quirk.
--- drivers/media/platform/sunxi/sun6i-csi/sun6i_csi.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/media/platform/sunxi/sun6i-csi/sun6i_csi.c +5 -0
@@ -909,10 +909,15 @@ static int sun6i_csi_remove(struct platform_device *pdev)static const struct sun6i_csi_variant sun6i_a31_csi = { }; +static const struct sun6i_csi_variant sun50i_a64_csi = { + .mod_rate =300000000 , +}; +static const struct of_device_id sun6i_csi_of_match[] = { { .compatible ="allwinner,sun6i-a31-csi" , .data = &sun6i_a31_csi, }, { .compatible ="allwinner,sun8i-h3-csi" , .data = &sun6i_a31_csi, }, { .compatible ="allwinner,sun8i-v3s-csi" , .data = &sun6i_a31_csi, }, + { .compatible ="allwinner,sun50i-a64-csi" , .data = &sun50i_a64_csi, }, {}, };MODULE_DEVICE_TABLE (of, sun6i_csi_of_match);
Signature · 1 line
2.18.0.321.gffc6fa0e3
PATCH v6 4/6 arm64: dts: allwinner: a64: Add A64 CSI controller
In reply to Jagan TekiAdd dts node details for Allwinner A64 CSI controller.
A64 CSI has similar features as like in H3, but the CSI_SCLK need to update it to 300MHz than default clock rate.
--- arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 20 +++++++++++++++++++ 1 file changed, 20 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +20 -0
@@ -532,6 +532,12 @@ interrupt-controller; #interrupt-cells = <3>; + csi_pins: csi-pins { + pins = "PE0", "PE2", "PE3", "PE4", "PE5", "PE6", + "PE7", "PE8", "PE9", "PE10", "PE11"; + function = "csi0"; + }; + i2c0_pins: i2c0_pins { pins = "PH0", "PH1"; function = "i2c0";
@@ -899,6 +905,20 @@ status = "disabled"; }; + csi: csi@1cb0000 { + compatible = "allwinner,sun50i-a64-csi"; + reg = <0x01cb0000 0x1000>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI_SCLK>, + <&ccu CLK_DRAM_CSI>; + clock-names = "bus", "mod", "ram"; + resets = <&ccu RST_BUS_CSI>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_pins>; + status = "disabled"; + }; + hdmi: hdmi@1ee0000 { compatible = "allwinner,sun50i-a64-dw-hdmi", "allwinner,sun8i-a83t-dw-hdmi";
Signature · 1 line
2.18.0.321.gffc6fa0e3
PATCH v6 5/6 arm64: dts: allwinner: a64: Add pinmux setting for CSI MCLK on PE1
In reply to Jagan TekiSome camera modules have the SoC feeding a master clock to the sensor instead of having a standalone crystal. This clock signal is generated from the clock control unit and output from the CSI MCLK function of pin PE1.
Add a pinmux setting for it for camera sensors to reference.
--- arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +5 -0
@@ -538,6 +538,11 @@ function = "csi0"; }; + csi_mclk_pin: csi-mclk { + pins = "PE1"; + function = "csi0"; + }; + i2c0_pins: i2c0_pins { pins = "PH0", "PH1"; function = "i2c0";
Signature · 1 line
2.18.0.321.gffc6fa0e3
PATCH v6 6/6 arm64: dts: allwinner: bananapi-m64: Add HDF5640 camera module
In reply to Jagan TekiBananapi M64 comes with an optional sensor based on the ov5640, add support for it with below pin information.
- PE13, PE12 via i2c-gpio bitbanging
- CLK_CSI_MCLK as external clock
- PE1 as external clock pin muxing
- DLDO3 as AVDD supply
- ALDO1 as DOVDD supply
- ELDO3 as DVDD supply
- PE16 gpio for reset pin
- PE17 gpio for powerdown pin
--- .../dts/allwinner/sun50i-a64-bananapi-m64.dts | 65 +++++++++++++++++++ 1 file changed, 65 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts +65 -0
@@ -60,6 +60,41 @@ stdout-path = "serial0:115200n8"; }; + i2c-csi { + compatible = "i2c-gpio"; + sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* CSI0-SDA: PE13 */ + scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* CSI0-SCK: PE12 */ + i2c-gpio,delay-us = <5>; + #address-cells = <1>; + #size-cells = <0>; + + ov5640: camera@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + clocks = <&ccu CLK_CSI_MCLK>; + clock-names = "xclk"; + + AVDD-supply = <®_dldo3>; + DOVDD-supply = <®_aldo1>; + DVDD-supply = <®_eldo3>; + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* CSI0-RST: PE16 */ + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* CSI0-PWDN: PE17 */ + + port { + ov5640_ep: endpoint { + remote-endpoint = <&csi_ep>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; + }; + hdmi-connector { compatible = "hdmi-connector"; type = "a";
@@ -106,6 +141,24 @@ status = "okay"; }; +&csi { + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + csi_ep: endpoint { + remote-endpoint = <&ov5640_ep>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; +}; + &dai { status = "okay"; };
@@ -296,6 +349,12 @@ regulator-name = "vcc-wifi"; }; +®_dldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi"; +}; + ®_dldo4 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>;
@@ -313,6 +372,12 @@ regulator-name = "cpvdd"; }; +®_eldo3 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "dvdd-csi"; +}; + ®_fldo1 { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>;
Signature · 1 line
2.18.0.321.gffc6fa0e3