vfio-pci: Introduce vfio_set_event_handler()
v2 cover vfio-pci: Introduce vfio_set_event_handler()
This small series introduces the vfio_set_event_handler() helper which allows to set up/tear down the VFIO signalling of eventfd for ERR, REQ and INTX irq indices.
On top of that, a new irq index is planned to signal DMA faults in nested mode use case. This would use exactly the same mechanics.
Eric Auger (2):
vfio-pci: Introduce vfio_set_event_handler helper
vfio-pci: Use vfio_set_event_handler in vfio_intx_enable
hw/vfio/pci.c | 347 +++++++++++++++++++++----------------------------- 1 file changed, 145 insertions(+), 202 deletions(-)
Signature · 1 line
2.20.1
PATCH v2 1/2 vfio-pci: Introduce vfio_set_event_handler helper
The code used to attach the eventfd handler for the ERR and REQ irq indices can be factorized into a helper. In subsequent patches we will extend this helper to support other irq indices.
We test whether the notification is allowed outside of the helper:
respectively check vdev->pci_aer and VFIO_FEATURE_ENABLE_REQ. Depending on the returned value we set vdev->pci_aer and vdev->req_enabled. An error handle is introduced for future usage although not strictly useful here.
---
v1 -> v2:
- s/vfio_register_event_notifier/vfio_set_event_handler
- turned into a void function
- do the qemu_set_fd_handler(*pfd, NULL, NULL, vdev) and event_notifier_cleanup on VFIO_DEVICE_SET_IRQS failure as reported by Alexey
- reset err in vfio_realize as reported by Cornelia
- Text/comment fixes suggested by Cornelia
--- hw/vfio/pci.c | 296 ++++++++++++++++++++++---------------------------- 1 file changed, 132 insertions(+), 164 deletions(-)
hw/vfio/pci.c +132 -164
@@ -105,6 +105,96 @@ static void vfio_intx_eoi(VFIODevice *vbasedev)vfio_unmask_single_irqindex (vbasedev,VFIO_PCI_INTX_IRQ_INDEX ); } +/* +* vfio_set_event_handler - setup/tear down eventfd +* notification and handling for IRQ indices that span over +* a single IRQ +* +* @vdev: VFIO device handle +* @index: IRQ index the eventfd/handler is associated with +* @enable: true means notifier chain needs to be set up +* @handler: handler to attach if @enable is true +* @errp: error handle +*/ +static void vfio_set_event_handler (VFIOPCIDevice *vdev, +int index, +bool enable, +void (*handler)(void *opaque), +Error **errp) +{ +struct vfio_irq_info irq_info = { .argsz =sizeof (irq_info), + .index = index }; +struct vfio_irq_set *irq_set; +EventNotifier *notifier; +int argsz, ret =0 ; +int32_t *pfd, fd; + +switch (index) { +case VFIO_PCI_REQ_IRQ_INDEX : + notifier = &vdev->req_notifier; +break ; +case VFIO_PCI_ERR_IRQ_INDEX : + notifier = &vdev->err_notifier; +break ; +default : +g_assert_not_reached (); + } + +if (ioctl (vdev->vbasedev.fd, +VFIO_DEVICE_GET_IRQ_INFO , &irq_info) <0 || irq_info.count <1 ) { +error_setg_errno (errp, errno,"No irq index %d available" , index); +return ; + } + +if (enable) { + ret =event_notifier_init (notifier,0 ); +if (ret) { +error_setg_errno (errp, -ret, +"Unable to init event notifier for irq index %d" , + index); +return ; + } + } + + argsz =sizeof (*irq_set) +sizeof (*pfd); + + irq_set =g_malloc0 (argsz); + irq_set->argsz = argsz; + irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | +VFIO_IRQ_SET_ACTION_TRIGGER ; + irq_set->index = index; + irq_set->start =0 ; + irq_set->count =1 ; + pfd = (int32_t *)&irq_set->data; + +if (!notifier) { +error_setg (errp,"Notifier not initialized for irq index %d" , index); +return ; + } + + fd =event_notifier_get_fd (notifier); + +if (enable) { +qemu_set_fd_handler (fd, handler,NULL , vdev); + *pfd = fd; + }else { + *pfd =-1 ; + } + + ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); +g_free (irq_set); + +if (ret) { +error_setg_errno (errp, -ret, +"Failed to %s eventfd signalling for index %d" , + enable ?"set up" :"tear down" , index); + } +if (ret || !enable) { +qemu_set_fd_handler (fd,NULL ,NULL , vdev); +event_notifier_cleanup (notifier); + } +} +static void vfio_intx_enable_kvm (VFIOPCIDevice *vdev,Error **errp) {#ifdef CONFIG_KVM
@@ -2621,86 +2711,6 @@ static void vfio_err_notifier_handler(void *opaque)vm_stop (RUN_STATE_INTERNAL_ERROR ); } -/* -* Registers error notifier for devices supporting error recovery. -* If we encounter a failure in this function, we report an error -* and continue after disabling error recovery support for the -* device. -*/ -static void vfio_register_err_notifier (VFIOPCIDevice *vdev) -{ -int ret; -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!vdev->pci_aer) { -return ; - } - -if (event_notifier_init (&vdev->err_notifier,0 )) { -error_report ("vfio: Unable to init event notifier for error detection" ); - vdev->pci_aer = false; -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_ERR_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->err_notifier); -qemu_set_fd_handler (*pfd, vfio_err_notifier_handler,NULL , vdev); - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_report ("vfio: Failed to set up error notification" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->err_notifier); - vdev->pci_aer = false; - } -g_free (irq_set); -} - -static void vfio_unregister_err_notifier (VFIOPCIDevice *vdev) -{ -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; -int ret; - -if (!vdev->pci_aer) { -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_ERR_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - *pfd =-1 ; - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_report ("vfio: Failed to de-assign error fd: %m" ); - } -g_free (irq_set); -qemu_set_fd_handler (event_notifier_get_fd (&vdev->err_notifier), -NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->err_notifier); -} -static void vfio_req_notifier_handler (void *opaque) {VFIOPCIDevice *vdev = opaque;
@@ -2716,86 +2726,6 @@ static void vfio_req_notifier_handler(void *opaque) } } -static void vfio_register_req_notifier (VFIOPCIDevice *vdev) -{ -struct vfio_irq_info irq_info = { .argsz =sizeof (irq_info), - .index =VFIO_PCI_REQ_IRQ_INDEX }; -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!(vdev->features &VFIO_FEATURE_ENABLE_REQ )) { -return ; - } - -if (ioctl (vdev->vbasedev.fd, -VFIO_DEVICE_GET_IRQ_INFO , &irq_info) <0 || irq_info.count <1 ) { -return ; - } - -if (event_notifier_init (&vdev->req_notifier,0 )) { -error_report ("vfio: Unable to init event notifier for device request" ); -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_REQ_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->req_notifier); -qemu_set_fd_handler (*pfd, vfio_req_notifier_handler,NULL , vdev); - -if (ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set)) { -error_report ("vfio: Failed to set up device request notification" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->req_notifier); - }else { - vdev->req_enabled = true; - } - -g_free (irq_set); -} - -static void vfio_unregister_req_notifier (VFIOPCIDevice *vdev) -{ -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!vdev->req_enabled) { -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_REQ_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - *pfd =-1 ; - -if (ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set)) { -error_report ("vfio: Failed to de-assign device request fd: %m" ); - } -g_free (irq_set); -qemu_set_fd_handler (event_notifier_get_fd (&vdev->req_notifier), -NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->req_notifier); - - vdev->req_enabled = false; -} -static void vfio_realize (PCIDevice *pdev,Error **errp) {VFIOPCIDevice *vdev =PCI_VFIO (pdev);
@@ -3069,8 +2999,33 @@ static void vfio_realize(PCIDevice *pdev, Error **errp) goto out_teardown; } -vfio_register_err_notifier (vdev); -vfio_register_req_notifier (vdev); +if (vdev->pci_aer) { +Error *err =NULL ; + +/* +* Registers error notifier for devices supporting error recovery. +* If we encounter a failure during registration, we report an error +* and continue after disabling error recovery support for the +* device. +*/ +vfio_set_event_handler (vdev,VFIO_PCI_ERR_IRQ_INDEX , true, + vfio_err_notifier_handler, &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + } + vdev->pci_aer = !err; + } + +if (vdev->features &VFIO_FEATURE_ENABLE_REQ ) { +Error *err =NULL ; + +vfio_set_event_handler (vdev,VFIO_PCI_REQ_IRQ_INDEX , true, + vfio_req_notifier_handler, &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + } + vdev->req_enabled = !err; + }vfio_setup_resetfn_quirk (vdev);return ;
@@ -3106,9 +3061,22 @@ static void vfio_instance_finalize(Object *obj)static void vfio_exitfn (PCIDevice *pdev) {VFIOPCIDevice *vdev =PCI_VFIO (pdev); +Error *err =NULL ; -vfio_unregister_req_notifier (vdev); -vfio_unregister_err_notifier (vdev); +if (vdev->req_enabled) { +vfio_set_event_handler (vdev,VFIO_PCI_REQ_IRQ_INDEX , + false,NULL , &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + } + } +if (vdev->pci_aer) { +vfio_set_event_handler (vdev,VFIO_PCI_ERR_IRQ_INDEX , + false,NULL , &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + } + }pci_device_set_intx_routing_notifier (&vdev->pdev,NULL );vfio_disable_interrupts (vdev);if (vdev->intx.mmap_timer) {
Signature · 1 line
2.20.1
Re: [Qemu-devel] [PATCH v2 1/2] vfio-pci: Introduce vfio_set_event_handler helper
Quoted 33 lines · On Thu, 17 Jan 2019 22:06:31 +0100 Eric Auger <[email protected]> wrote:
The code used to attach the eventfd handler for the ERR and REQ irq indices can be factorized into a helper. In subsequent patches we will extend this helper to support other irq indices.
We test whether the notification is allowed outside of the helper:
respectively checkvdev->pci_aerandVFIO_FEATURE_ENABLE_REQ. Depending on the returned value we setvdev->pci_aerandvdev->req_enabled. An error handle is introduced for future usage although not strictly useful here.Signed-off-by Eric Auger <[email protected]>---
v1 -> v2:
- s/vfio_register_event_notifier/vfio_set_event_handler
- turned into a void function
- do theqemu_set_fd_handler(*pfd, NULL, NULL, vdev)andevent_notifier_cleanuponVFIO_DEVICE_SET_IRQSfailure as reported by Alexey
- reset err invfio_realizeas reported by Cornelia
- Text/comment fixes suggested by Cornelia--- hw/vfio/pci.c | 296 ++++++++++++++++++++++---------------------------- 1 file changed, 132 insertions(+), 164 deletions(-)hw/vfio/pci.c +0
-0@@ -105,6 +105,96 @@ static void vfio_intx_eoi(VFIODevice *vbasedev)vfio_unmask_single_irqindex (vbasedev,VFIO_PCI_INTX_IRQ_INDEX ); }
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 116
Quoted 10 lines
hw/vfio/pci.c +9
-0+/* +* vfio_set_event_handler - setup/tear down eventfd +* notification and handling for IRQ indices that span over +* a single IRQ +* +* @vdev: VFIO device handle +* @index: IRQ index the eventfd/handler is associated with +* @enable: true means notifier chain needs to be set up +* @handler: handler to attach if @enable is true
Therefore @enable is redundant.
Quoted 12 lines
hw/vfio/pci.c +12
-0+* @errp: error handle +*/ +static void vfio_set_event_handler (VFIOPCIDevice *vdev, +int index, +bool enable, +void (*handler)(void *opaque), +Error **errp) +{ +struct vfio_irq_info irq_info = { .argsz =sizeof (irq_info), + .index = index }; +struct vfio_irq_set *irq_set; +EventNotifier *notifier;
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 138
Quoted 10 lines
hw/vfio/pci.c +10
-0+int argsz, ret =0 ; +int32_t *pfd, fd; + +switch (index) { +case VFIO_PCI_REQ_IRQ_INDEX : + notifier = &vdev->req_notifier; +break ; +case VFIO_PCI_ERR_IRQ_INDEX : + notifier = &vdev->err_notifier; +break ;
This blows the abstraction of a helper that this seems to be trying to create, seems cleaner to pass @notifier.
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 146
Quoted 8 lines
hw/vfio/pci.c +8
-0+default : +g_assert_not_reached (); + } + +if (ioctl (vdev->vbasedev.fd, +VFIO_DEVICE_GET_IRQ_INFO , &irq_info) <0 || irq_info.count <1 ) { +error_setg_errno (errp, errno,"No irq index %d available" , index); +return ;
The implicit count, aka sub-index, is also problematic for the abstraction. Can we tackle applying this to MSI/X to validate if this needs to go another step to allow the caller to specify index and sub-index?
Quoted 17 lines
hw/vfio/pci.c +17
-0+ } + +if (enable) { + ret =event_notifier_init (notifier,0 ); +if (ret) { +error_setg_errno (errp, -ret, +"Unable to init event notifier for irq index %d" , + index); +return ; + } + } + + argsz =sizeof (*irq_set) +sizeof (*pfd); + + irq_set =g_malloc0 (argsz); + irq_set->argsz = argsz; + irq_set->flags = VFIO_IRQ_SET_DATA_EVENTFD |
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 173
Quoted 10 lines
hw/vfio/pci.c +10
-0+VFIO_IRQ_SET_ACTION_TRIGGER ; + irq_set->index = index; + irq_set->start =0 ; + irq_set->count =1 ; + pfd = (int32_t *)&irq_set->data; + +if (!notifier) { +error_setg (errp,"Notifier not initialized for irq index %d" , index); +return ; + }
What is this supposed to check? @notifier is not NULL initialized, the case statement will assert if it doesn't get set, and this doesn't actually test if it's properly initialized.
Quoted 13 lines
hw/vfio/pci.c +13
-0+ + fd =event_notifier_get_fd (notifier); + +if (enable) { +qemu_set_fd_handler (fd, handler,NULL , vdev); + *pfd = fd; + }else { + *pfd =-1 ; + } + + ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); +g_free (irq_set); +
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 196
Quoted 10 lines
hw/vfio/pci.c +10
-0+if (ret) { +error_setg_errno (errp, -ret, +"Failed to %s eventfd signalling for index %d" , + enable ?"set up" :"tear down" , index); + } +if (ret || !enable) { +qemu_set_fd_handler (fd,NULL ,NULL , vdev); +event_notifier_cleanup (notifier); + } +}
Suggest passing @notifier as a parameter and using @handler in place of @enable, more generic and more obvious calling convention.
Quoted 188 lines
hw/vfio/pci.c +5
-162+static void vfio_intx_enable_kvm (VFIOPCIDevice *vdev,Error **errp) {#ifdef CONFIG_KVM @@ -2621,86 +2711,6 @@ static void vfio_err_notifier_handler(void *opaque)vm_stop (RUN_STATE_INTERNAL_ERROR ); } -/* -* Registers error notifier for devices supporting error recovery. -* If we encounter a failure in this function, we report an error -* and continue after disabling error recovery support for the -* device. -*/ -static void vfio_register_err_notifier (VFIOPCIDevice *vdev) -{ -int ret; -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!vdev->pci_aer) { -return ; - } - -if (event_notifier_init (&vdev->err_notifier,0 )) { -error_report ("vfio: Unable to init event notifier for error detection" ); - vdev->pci_aer = false; -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_ERR_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->err_notifier); -qemu_set_fd_handler (*pfd, vfio_err_notifier_handler,NULL , vdev); - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_report ("vfio: Failed to set up error notification" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->err_notifier); - vdev->pci_aer = false; - } -g_free (irq_set); -} - -static void vfio_unregister_err_notifier (VFIOPCIDevice *vdev) -{ -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; -int ret; - -if (!vdev->pci_aer) { -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_ERR_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - *pfd =-1 ; - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_report ("vfio: Failed to de-assign error fd: %m" ); - } -g_free (irq_set); -qemu_set_fd_handler (event_notifier_get_fd (&vdev->err_notifier), -NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->err_notifier); -} -static void vfio_req_notifier_handler (void *opaque) {VFIOPCIDevice *vdev = opaque;@@ -2716,86 +2726,6 @@ static void vfio_req_notifier_handler(void *opaque) } } -static void vfio_register_req_notifier (VFIOPCIDevice *vdev) -{ -struct vfio_irq_info irq_info = { .argsz =sizeof (irq_info), - .index =VFIO_PCI_REQ_IRQ_INDEX }; -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!(vdev->features &VFIO_FEATURE_ENABLE_REQ )) { -return ; - } - -if (ioctl (vdev->vbasedev.fd, -VFIO_DEVICE_GET_IRQ_INFO , &irq_info) <0 || irq_info.count <1 ) { -return ; - } - -if (event_notifier_init (&vdev->req_notifier,0 )) { -error_report ("vfio: Unable to init event notifier for device request" ); -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_REQ_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->req_notifier); -qemu_set_fd_handler (*pfd, vfio_req_notifier_handler,NULL , vdev); - -if (ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set)) { -error_report ("vfio: Failed to set up device request notification" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->req_notifier); - }else { - vdev->req_enabled = true; - } - -g_free (irq_set); -} - -static void vfio_unregister_req_notifier (VFIOPCIDevice *vdev) -{ -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!vdev->req_enabled) { -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_REQ_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - *pfd =-1 ; - -if (ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set)) { -error_report ("vfio: Failed to de-assign device request fd: %m" ); - } -g_free (irq_set); -qemu_set_fd_handler (event_notifier_get_fd (&vdev->req_notifier), -NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->req_notifier); - - vdev->req_enabled = false; -} -static void vfio_realize (PCIDevice *pdev,Error **errp) {VFIOPCIDevice *vdev =PCI_VFIO (pdev);@@ -3069,8 +2999,33 @@ static void vfio_realize(PCIDevice *pdev, Error **errp) goto out_teardown; } -vfio_register_err_notifier (vdev); -vfio_register_req_notifier (vdev); +if (vdev->pci_aer) { +Error *err =NULL ; + +/*
hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3015
Quoted 10 lines
hw/vfio/pci.c +10
-0+* Registers error notifier for devices supporting error recovery. +* If we encounter a failure during registration, we report an error +* and continue after disabling error recovery support for the +* device. +*/ +vfio_set_event_handler (vdev,VFIO_PCI_ERR_IRQ_INDEX , true, + vfio_err_notifier_handler, &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + }
Why not just return -1 on error and zero on success so we can call as:
if (vfio_set_event_handler(...)) {
warn_reportf_err()...
}hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3016
Quoted 1 line
hw/vfio/pci.c +1
-0+ vdev->pci_aer = !err;
We could also avoid this weirdness of this negation to get a bool.
hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3017
Quoted 1 line
hw/vfio/pci.c +1
-0+ }
It's not obvious how doing away with the register/unregister helpers and doing everything inline is an improvement. Simple helpers calling common helpers seems better than inline sprawl calling common helpers. Thanks,
Alex
Quoted 39 lines
hw/vfio/pci.c +26
-2+ +if (vdev->features &VFIO_FEATURE_ENABLE_REQ ) { +Error *err =NULL ; + +vfio_set_event_handler (vdev,VFIO_PCI_REQ_IRQ_INDEX , true, + vfio_req_notifier_handler, &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + } + vdev->req_enabled = !err; + }vfio_setup_resetfn_quirk (vdev);return ;@@ -3106,9 +3061,22 @@ static void vfio_instance_finalize(Object *obj)static void vfio_exitfn (PCIDevice *pdev) {VFIOPCIDevice *vdev =PCI_VFIO (pdev); +Error *err =NULL ; -vfio_unregister_req_notifier (vdev); -vfio_unregister_err_notifier (vdev); +if (vdev->req_enabled) { +vfio_set_event_handler (vdev,VFIO_PCI_REQ_IRQ_INDEX , + false,NULL , &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + } + } +if (vdev->pci_aer) { +vfio_set_event_handler (vdev,VFIO_PCI_ERR_IRQ_INDEX , + false,NULL , &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + } + }pci_device_set_intx_routing_notifier (&vdev->pdev,NULL );vfio_disable_interrupts (vdev);if (vdev->intx.mmap_timer) {
Re: [Qemu-devel] [PATCH v2 1/2] vfio-pci: Introduce vfio_set_event_handler helper
Hi Alex,
Quoted 37 lines · Alex Williamson
Quoted 34 lines · On Thu, 17 Jan 2019 22:06:31 +0100 Eric Auger <[email protected]> wrote:
The code used to attach the eventfd handler for the ERR and REQ irq indices can be factorized into a helper. In subsequent patches we will extend this helper to support other irq indices.
We test whether the notification is allowed outside of the helper:
respectively checkvdev->pci_aerandVFIO_FEATURE_ENABLE_REQ. Depending on the returned value we setvdev->pci_aerandvdev->req_enabled. An error handle is introduced for future usage although not strictly useful here.Signed-off-by Eric Auger <[email protected]>---
v1 -> v2:
- s/vfio_register_event_notifier/vfio_set_event_handler
- turned into a void function
- do theqemu_set_fd_handler(*pfd, NULL, NULL, vdev)andevent_notifier_cleanuponVFIO_DEVICE_SET_IRQSfailure as reported by Alexey
- reset err invfio_realizeas reported by Cornelia
- Text/comment fixes suggested by Cornelia--- hw/vfio/pci.c | 296 ++++++++++++++++++++++---------------------------- 1 file changed, 132 insertions(+), 164 deletions(-)hw/vfio/pci.c +0
-0@@ -105,6 +105,96 @@ static void vfio_intx_eoi(VFIODevice *vbasedev)vfio_unmask_single_irqindex (vbasedev,VFIO_PCI_INTX_IRQ_INDEX ); }
Quoted 11 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 116
Quoted 9 lines
hw/vfio/pci.c +9
-0+/* +* vfio_set_event_handler - setup/tear down eventfd +* notification and handling for IRQ indices that span over +* a single IRQ +* +* @vdev: VFIO device handle +* @index: IRQ index the eventfd/handler is associated with +* @enable: true means notifier chain needs to be set up +* @handler: handler to attach if @enable is true Therefore @enable is redundant.
agreed
Quoted 18 lines
Quoted 18 lines
hw/vfio/pci.c +17
-0+* @errp: error handle +*/ +static void vfio_set_event_handler (VFIOPCIDevice *vdev, +int index, +bool enable, +void (*handler)(void *opaque), +Error **errp) +{ +struct vfio_irq_info irq_info = { .argsz =sizeof (irq_info), + .index = index }; +struct vfio_irq_set *irq_set; +EventNotifier *notifier; +int argsz, ret =0 ; +int32_t *pfd, fd; + +switch (index) { +case VFIO_PCI_REQ_IRQ_INDEX :
Quoted 8 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 138
Quoted 5 lines
hw/vfio/pci.c +5
-0+ notifier = &vdev->req_notifier; +break ; +case VFIO_PCI_ERR_IRQ_INDEX : + notifier = &vdev->err_notifier; +break ;This blows the abstraction of a helper that this seems to be trying to create, seems cleaner to pass @notifier.
Not sure I really get the point eventually. Don't we have the following
indirection: irq index -> notifier.fd -> handler. When we want to use this helper don't we simply want to associate an handler to a given IRQ index without taking care of the notifier mechanics.
As discussed with Alexey, moving the notifier initialization outside of this helper removes some code factorization.
Quoted 10 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 146
Quoted 9 lines
hw/vfio/pci.c +8
-0+default : +g_assert_not_reached (); + } + +if (ioctl (vdev->vbasedev.fd, +VFIO_DEVICE_GET_IRQ_INFO , &irq_info) <0 || irq_info.count <1 ) { +error_setg_errno (errp, errno,"No irq index %d available" , index); +return ;
Quoted 4 lines
The implicit count, aka sub-index, is also problematic for the abstraction. Can we tackle applying this to MSI/X to validate if this needs to go another step to allow the caller to specify index and sub-index?
I mentioned the helper stands for IRQ indices with no sub-index. I am afraid applying this to MSI/X would oblige use to revisit a bulk of code without knowing whether it is interesting.
Quoted 24 lines
Quoted 24 lines
hw/vfio/pci.c +23
-0+ } + +if (enable) { + ret =event_notifier_init (notifier,0 ); +if (ret) { +error_setg_errno (errp, -ret, +"Unable to init event notifier for irq index %d" , + index); +return ; + } + } + + argsz =sizeof (*irq_set) +sizeof (*pfd); + + irq_set =g_malloc0 (argsz); + irq_set->argsz = argsz; + irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | +VFIO_IRQ_SET_ACTION_TRIGGER ; + irq_set->index = index; + irq_set->start =0 ; + irq_set->count =1 ; + pfd = (int32_t *)&irq_set->data; +
Quoted 8 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 173
Quoted 4 lines
hw/vfio/pci.c +4
-0+if (!notifier) { +error_setg (errp,"Notifier not initialized for irq index %d" , index); +return ; + }What is this supposed to check? @notifier is not NULL initialized, the case statement will assert if it doesn't get set, and this doesn't actually test if it's properly initialized.
The goal was to check the helper was not called on a valid IRQ index with !enabled while the notifier was not properly initialized. But if we trust the calling sites I can remove it.
Quoted 19 lines
Quoted 19 lines
hw/vfio/pci.c +18
-0+ + fd =event_notifier_get_fd (notifier); + +if (enable) { +qemu_set_fd_handler (fd, handler,NULL , vdev); + *pfd = fd; + }else { + *pfd =-1 ; + } + + ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); +g_free (irq_set); + +if (ret) { +error_setg_errno (errp, -ret, +"Failed to %s eventfd signalling for index %d" , + enable ?"set up" :"tear down" , index); + }
Quoted 8 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 196
Quoted 5 lines
hw/vfio/pci.c +5
-0+if (ret || !enable) { +qemu_set_fd_handler (fd,NULL ,NULL , vdev); +event_notifier_cleanup (notifier); + } +}Suggest passing @notifier as a parameter and using @handler in place of @enable, more generic and more obvious calling convention.
ok
Quoted 202 lines
Quoted 189 lines
hw/vfio/pci.c +5
-162+static void vfio_intx_enable_kvm (VFIOPCIDevice *vdev,Error **errp) {#ifdef CONFIG_KVM @@ -2621,86 +2711,6 @@ static void vfio_err_notifier_handler(void *opaque)vm_stop (RUN_STATE_INTERNAL_ERROR ); } -/* -* Registers error notifier for devices supporting error recovery. -* If we encounter a failure in this function, we report an error -* and continue after disabling error recovery support for the -* device. -*/ -static void vfio_register_err_notifier (VFIOPCIDevice *vdev) -{ -int ret; -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!vdev->pci_aer) { -return ; - } - -if (event_notifier_init (&vdev->err_notifier,0 )) { -error_report ("vfio: Unable to init event notifier for error detection" ); - vdev->pci_aer = false; -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_ERR_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->err_notifier); -qemu_set_fd_handler (*pfd, vfio_err_notifier_handler,NULL , vdev); - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_report ("vfio: Failed to set up error notification" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->err_notifier); - vdev->pci_aer = false; - } -g_free (irq_set); -} - -static void vfio_unregister_err_notifier (VFIOPCIDevice *vdev) -{ -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; -int ret; - -if (!vdev->pci_aer) { -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_ERR_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - *pfd =-1 ; - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_report ("vfio: Failed to de-assign error fd: %m" ); - } -g_free (irq_set); -qemu_set_fd_handler (event_notifier_get_fd (&vdev->err_notifier), -NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->err_notifier); -} -static void vfio_req_notifier_handler (void *opaque) {VFIOPCIDevice *vdev = opaque;@@ -2716,86 +2726,6 @@ static void vfio_req_notifier_handler(void *opaque) } } -static void vfio_register_req_notifier (VFIOPCIDevice *vdev) -{ -struct vfio_irq_info irq_info = { .argsz =sizeof (irq_info), - .index =VFIO_PCI_REQ_IRQ_INDEX }; -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!(vdev->features &VFIO_FEATURE_ENABLE_REQ )) { -return ; - } - -if (ioctl (vdev->vbasedev.fd, -VFIO_DEVICE_GET_IRQ_INFO , &irq_info) <0 || irq_info.count <1 ) { -return ; - } - -if (event_notifier_init (&vdev->req_notifier,0 )) { -error_report ("vfio: Unable to init event notifier for device request" ); -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_REQ_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->req_notifier); -qemu_set_fd_handler (*pfd, vfio_req_notifier_handler,NULL , vdev); - -if (ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set)) { -error_report ("vfio: Failed to set up device request notification" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->req_notifier); - }else { - vdev->req_enabled = true; - } - -g_free (irq_set); -} - -static void vfio_unregister_req_notifier (VFIOPCIDevice *vdev) -{ -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!vdev->req_enabled) { -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_REQ_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - *pfd =-1 ; - -if (ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set)) { -error_report ("vfio: Failed to de-assign device request fd: %m" ); - } -g_free (irq_set); -qemu_set_fd_handler (event_notifier_get_fd (&vdev->req_notifier), -NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->req_notifier); - - vdev->req_enabled = false; -} -static void vfio_realize (PCIDevice *pdev,Error **errp) {VFIOPCIDevice *vdev =PCI_VFIO (pdev);@@ -3069,8 +2999,33 @@ static void vfio_realize(PCIDevice *pdev, Error **errp) goto out_teardown; } -vfio_register_err_notifier (vdev); -vfio_register_req_notifier (vdev); +if (vdev->pci_aer) { +Error *err =NULL ; + +/* hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3015
Quoted 10 lines
hw/vfio/pci.c +10
-0+* Registers error notifier for devices supporting error recovery. +* If we encounter a failure during registration, we report an error +* and continue after disabling error recovery support for the +* device. +*/ +vfio_set_event_handler (vdev,VFIO_PCI_ERR_IRQ_INDEX , true, + vfio_err_notifier_handler, &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + }Why not just return -1 on error and zero on success so we can call as:
Quoted 3 lines
if (vfio_set_event_handler(...)) {
warn_reportf_err()...
}The point is that if you have both the err and the returned value , it is error prone as you expect both to be consistent (reported by Alexey). You expect err to be set whenever you have a an error returned. The calling site can call warn_reportf_err() whenever the function returns an error and if somebody, later on, ignores to set the err on error case, it will crash.
Reading again Markus' answer
(https://www.mail-archive.com/[email protected]/msg402893.html), I may put the returned value back and make sure my code is consistent ;-)
Quoted 4 lines
hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3016
Quoted 2 lines
hw/vfio/pci.c +1
-0+ vdev->pci_aer = !err;We could also avoid this weirdness of this negation to get a bool.
ok
Quoted 7 lines
hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3017
Quoted 2 lines
hw/vfio/pci.c +1
-0+ }It's not obvious how doing away with the register/unregister helpers and doing everything inline is an improvement. Simple helpers calling common helpers seems better than inline sprawl calling common helpers. Thanks,
On my side I noticed vfio_(un)register_err|req_notifier are mostly identical at the exception of the irq index/notifier and enable logic. As I am about to propose another single index IRQ, I am going to add 2 similar functions and I felt it was a pitty. Now it is not a big deal and if you prefer to keep the code as it is I will simply add those.
Thanks
Eric
Quoted 43 lines
Alex
Quoted 39 lines
hw/vfio/pci.c +26
-2+ +if (vdev->features &VFIO_FEATURE_ENABLE_REQ ) { +Error *err =NULL ; + +vfio_set_event_handler (vdev,VFIO_PCI_REQ_IRQ_INDEX , true, + vfio_req_notifier_handler, &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + } + vdev->req_enabled = !err; + }vfio_setup_resetfn_quirk (vdev);return ;@@ -3106,9 +3061,22 @@ static void vfio_instance_finalize(Object *obj)static void vfio_exitfn (PCIDevice *pdev) {VFIOPCIDevice *vdev =PCI_VFIO (pdev); +Error *err =NULL ; -vfio_unregister_req_notifier (vdev); -vfio_unregister_err_notifier (vdev); +if (vdev->req_enabled) { +vfio_set_event_handler (vdev,VFIO_PCI_REQ_IRQ_INDEX , + false,NULL , &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + } + } +if (vdev->pci_aer) { +vfio_set_event_handler (vdev,VFIO_PCI_ERR_IRQ_INDEX , + false,NULL , &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + } + }pci_device_set_intx_routing_notifier (&vdev->pdev,NULL );vfio_disable_interrupts (vdev);if (vdev->intx.mmap_timer) {
Re: [Qemu-devel] [PATCH v2 1/2] vfio-pci: Introduce vfio_set_event_handler helper
Quoted 80 lines · On Wed, 23 Jan 2019 16:28:50 +0100 Auger Eric <[email protected]> wrote:
Hi Alex,
Quoted 37 lines · Alex Williamson
Quoted 34 lines · On Thu, 17 Jan 2019 22:06:31 +0100 Eric Auger <[email protected]> wrote:
The code used to attach the eventfd handler for the ERR and REQ irq indices can be factorized into a helper. In subsequent patches we will extend this helper to support other irq indices.
We test whether the notification is allowed outside of the helper:
respectively checkvdev->pci_aerandVFIO_FEATURE_ENABLE_REQ. Depending on the returned value we setvdev->pci_aerandvdev->req_enabled. An error handle is introduced for future usage although not strictly useful here.Signed-off-by Eric Auger <[email protected]>---
v1 -> v2:
- s/vfio_register_event_notifier/vfio_set_event_handler
- turned into a void function
- do theqemu_set_fd_handler(*pfd, NULL, NULL, vdev)andevent_notifier_cleanuponVFIO_DEVICE_SET_IRQSfailure as reported by Alexey
- reset err invfio_realizeas reported by Cornelia
- Text/comment fixes suggested by Cornelia--- hw/vfio/pci.c | 296 ++++++++++++++++++++++---------------------------- 1 file changed, 132 insertions(+), 164 deletions(-)hw/vfio/pci.c +0
-0@@ -105,6 +105,96 @@ static void vfio_intx_eoi(VFIODevice *vbasedev)vfio_unmask_single_irqindex (vbasedev,VFIO_PCI_INTX_IRQ_INDEX ); }Quoted 11 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 116
Quoted 9 lines
hw/vfio/pci.c +9
-0+/* +* vfio_set_event_handler - setup/tear down eventfd +* notification and handling for IRQ indices that span over +* a single IRQ +* +* @vdev: VFIO device handle +* @index: IRQ index the eventfd/handler is associated with +* @enable: true means notifier chain needs to be set up +* @handler: handler to attach if @enable is true Therefore @enable is redundant.
agreed
Quoted 18 lines
Quoted 18 lines
hw/vfio/pci.c +17
-0+* @errp: error handle +*/ +static void vfio_set_event_handler (VFIOPCIDevice *vdev, +int index, +bool enable, +void (*handler)(void *opaque), +Error **errp) +{ +struct vfio_irq_info irq_info = { .argsz =sizeof (irq_info), + .index = index }; +struct vfio_irq_set *irq_set; +EventNotifier *notifier; +int argsz, ret =0 ; +int32_t *pfd, fd; + +switch (index) { +case VFIO_PCI_REQ_IRQ_INDEX :Quoted 8 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 138
Quoted 5 lines
hw/vfio/pci.c +5
-0+ notifier = &vdev->req_notifier; +break ; +case VFIO_PCI_ERR_IRQ_INDEX : + notifier = &vdev->err_notifier; +break ;This blows the abstraction of a helper that this seems to be trying to create, seems cleaner to pass @notifier.
Quoted 4 lines
Not sure I really get the point eventually. Don't we have the following
indirection: irq index -> notifier.fd -> handler. When we want to use this helper don't we simply want to associate an handler to a given IRQ index without taking care of the notifier mechanics.
With that logic we could eliminate all the parameters and have the function infer everything. I don't think that's how we build a good helper function though. To me the function is wanting to set or clear a handler for an irq index, but it also needs the notifier to trigger to call that handler, so we simply need to pass that as another arg rather than inferring it from the index.
Quoted 2 lines
As discussed with Alexey, moving the notifier initialization outside of this helper removes some code factorization.
I don't see why passing the notifier implies this function cannot perform the init and cleanup of that notifier.
Quoted 9 lines
Quoted 9 lines
Quoted 8 lines
hw/vfio/pci.c +8
-0+default : +g_assert_not_reached (); + } + +if (ioctl (vdev->vbasedev.fd, +VFIO_DEVICE_GET_IRQ_INFO , &irq_info) <0 || irq_info.count <1 ) { +error_setg_errno (errp, errno,"No irq index %d available" , index); +return ;
Quoted 7 lines
Quoted 4 lines
The implicit count, aka sub-index, is also problematic for the abstraction. Can we tackle applying this to MSI/X to validate if this needs to go another step to allow the caller to specify index and sub-index?
I mentioned the helper stands for IRQ indices with no sub-index. I am afraid applying this to MSI/X would oblige use to revisit a bulk of code without knowing whether it is interesting.
I'm afraid that the helper shows some holes with INTx integration and I'm wondering if MSI/X integration would show us how to improve the helper.
Quoted 31 lines
Quoted 23 lines
Quoted 23 lines
hw/vfio/pci.c +23
-0+ } + +if (enable) { + ret =event_notifier_init (notifier,0 ); +if (ret) { +error_setg_errno (errp, -ret, +"Unable to init event notifier for irq index %d" , + index); +return ; + } + } + + argsz =sizeof (*irq_set) +sizeof (*pfd); + + irq_set =g_malloc0 (argsz); + irq_set->argsz = argsz; + irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | +VFIO_IRQ_SET_ACTION_TRIGGER ; + irq_set->index = index; + irq_set->start =0 ; + irq_set->count =1 ; + pfd = (int32_t *)&irq_set->data; +Quoted 8 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 173
Quoted 4 lines
hw/vfio/pci.c +4
-0+if (!notifier) { +error_setg (errp,"Notifier not initialized for irq index %d" , index); +return ; + }What is this supposed to check? @notifier is not NULL initialized, the case statement will assert if it doesn't get set, and this doesn't actually test if it's properly initialized.
Quoted 3 lines
The goal was to check the helper was not called on a valid IRQ index with !enabled while the notifier was not properly initialized. But if we trust the calling sites I can remove it.
But this doesn't test if the notifier is initialized. Seems you'd need to check if fd of the notifier is -1.
Quoted 240 lines
Quoted 19 lines
Quoted 19 lines
hw/vfio/pci.c +18
-0+ + fd =event_notifier_get_fd (notifier); + +if (enable) { +qemu_set_fd_handler (fd, handler,NULL , vdev); + *pfd = fd; + }else { + *pfd =-1 ; + } + + ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); +g_free (irq_set); + +if (ret) { +error_setg_errno (errp, -ret, +"Failed to %s eventfd signalling for index %d" , + enable ?"set up" :"tear down" , index); + }Quoted 8 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 196
Quoted 5 lines
hw/vfio/pci.c +5
-0+if (ret || !enable) { +qemu_set_fd_handler (fd,NULL ,NULL , vdev); +event_notifier_cleanup (notifier); + } +}Suggest passing @notifier as a parameter and using @handler in place of @enable, more generic and more obvious calling convention.
ok
Quoted 202 lines
Quoted 189 lines
hw/vfio/pci.c +5
-162+static void vfio_intx_enable_kvm (VFIOPCIDevice *vdev,Error **errp) {#ifdef CONFIG_KVM @@ -2621,86 +2711,6 @@ static void vfio_err_notifier_handler(void *opaque)vm_stop (RUN_STATE_INTERNAL_ERROR ); } -/* -* Registers error notifier for devices supporting error recovery. -* If we encounter a failure in this function, we report an error -* and continue after disabling error recovery support for the -* device. -*/ -static void vfio_register_err_notifier (VFIOPCIDevice *vdev) -{ -int ret; -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!vdev->pci_aer) { -return ; - } - -if (event_notifier_init (&vdev->err_notifier,0 )) { -error_report ("vfio: Unable to init event notifier for error detection" ); - vdev->pci_aer = false; -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_ERR_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->err_notifier); -qemu_set_fd_handler (*pfd, vfio_err_notifier_handler,NULL , vdev); - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_report ("vfio: Failed to set up error notification" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->err_notifier); - vdev->pci_aer = false; - } -g_free (irq_set); -} - -static void vfio_unregister_err_notifier (VFIOPCIDevice *vdev) -{ -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; -int ret; - -if (!vdev->pci_aer) { -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_ERR_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - *pfd =-1 ; - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_report ("vfio: Failed to de-assign error fd: %m" ); - } -g_free (irq_set); -qemu_set_fd_handler (event_notifier_get_fd (&vdev->err_notifier), -NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->err_notifier); -} -static void vfio_req_notifier_handler (void *opaque) {VFIOPCIDevice *vdev = opaque;@@ -2716,86 +2726,6 @@ static void vfio_req_notifier_handler(void *opaque) } } -static void vfio_register_req_notifier (VFIOPCIDevice *vdev) -{ -struct vfio_irq_info irq_info = { .argsz =sizeof (irq_info), - .index =VFIO_PCI_REQ_IRQ_INDEX }; -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!(vdev->features &VFIO_FEATURE_ENABLE_REQ )) { -return ; - } - -if (ioctl (vdev->vbasedev.fd, -VFIO_DEVICE_GET_IRQ_INFO , &irq_info) <0 || irq_info.count <1 ) { -return ; - } - -if (event_notifier_init (&vdev->req_notifier,0 )) { -error_report ("vfio: Unable to init event notifier for device request" ); -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_REQ_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->req_notifier); -qemu_set_fd_handler (*pfd, vfio_req_notifier_handler,NULL , vdev); - -if (ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set)) { -error_report ("vfio: Failed to set up device request notification" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->req_notifier); - }else { - vdev->req_enabled = true; - } - -g_free (irq_set); -} - -static void vfio_unregister_req_notifier (VFIOPCIDevice *vdev) -{ -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!vdev->req_enabled) { -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_REQ_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - *pfd =-1 ; - -if (ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set)) { -error_report ("vfio: Failed to de-assign device request fd: %m" ); - } -g_free (irq_set); -qemu_set_fd_handler (event_notifier_get_fd (&vdev->req_notifier), -NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->req_notifier); - - vdev->req_enabled = false; -} -static void vfio_realize (PCIDevice *pdev,Error **errp) {VFIOPCIDevice *vdev =PCI_VFIO (pdev);@@ -3069,8 +2999,33 @@ static void vfio_realize(PCIDevice *pdev, Error **errp) goto out_teardown; } -vfio_register_err_notifier (vdev); -vfio_register_req_notifier (vdev); +if (vdev->pci_aer) { +Error *err =NULL ; + +/* hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3015
Quoted 10 lines
hw/vfio/pci.c +10
-0+* Registers error notifier for devices supporting error recovery. +* If we encounter a failure during registration, we report an error +* and continue after disabling error recovery support for the +* device. +*/ +vfio_set_event_handler (vdev,VFIO_PCI_ERR_IRQ_INDEX , true, + vfio_err_notifier_handler, &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + }Why not just return -1 on error and zero on success so we can call as:
Quoted 3 lines
if (vfio_set_event_handler(...)) { warn_reportf_err()... }The point is that if you have both the err and the returned value , it is error prone as you expect both to be consistent (reported by Alexey). You expect err to be set whenever you have a an error returned. The calling site can call
warn_reportf_err()whenever the function returns an error and if somebody, later on, ignores to set the err on error case, it will crash.
Quoted 3 lines
Reading again Markus' answer
(https://www.mail-archive.com/[email protected]/msg402893.html), I may put the returned value back and make sure my code is consistent ;-)
It's not like C programmers aren't used to checking return values. Not exactly analogous, but we check the return value of an ioctl() then look at errno. So it feels like standard practice to return an error code on failure and try to only use void returns for functions that cannot fail.
Quoted 13 lines
Quoted 4 lines
hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3016
Quoted 2 lines
hw/vfio/pci.c +1
-0+ vdev->pci_aer = !err;We could also avoid this weirdness of this negation to get a bool.
ok
Quoted 7 lines
hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3017
Quoted 2 lines
hw/vfio/pci.c +1
-0+ }It's not obvious how doing away with the register/unregister helpers and doing everything inline is an improvement. Simple helpers calling common helpers seems better than inline sprawl calling common helpers. Thanks,
Quoted 5 lines
On my side I noticed vfio_(un)register_err|req_notifier are mostly identical at the exception of the irq index/notifier and enable logic. As I am about to propose another single index IRQ, I am going to add 2 similar functions and I felt it was a pitty. Now it is not a big deal and if you prefer to keep the code as it is I will simply add those.
Simple helper functions are a good thing IMO, especially with the prospects of open coding two more setup and teardown sections further bloating the base function. Thanks,
Alex
Re: [Qemu-devel] [PATCH v2 1/2] vfio-pci: Introduce vfio_set_event_handler helper
Hi Alex,
Quoted 88 lines · Alex Williamson
Quoted 80 lines · On Wed, 23 Jan 2019 16:28:50 +0100 Auger Eric <[email protected]> wrote:
Hi Alex,
Quoted 37 lines · Alex Williamson
Quoted 34 lines · On Thu, 17 Jan 2019 22:06:31 +0100 Eric Auger <[email protected]> wrote:
The code used to attach the eventfd handler for the ERR and REQ irq indices can be factorized into a helper. In subsequent patches we will extend this helper to support other irq indices.
We test whether the notification is allowed outside of the helper:
respectively checkvdev->pci_aerandVFIO_FEATURE_ENABLE_REQ. Depending on the returned value we setvdev->pci_aerandvdev->req_enabled. An error handle is introduced for future usage although not strictly useful here.Signed-off-by Eric Auger <[email protected]>---
v1 -> v2:
- s/vfio_register_event_notifier/vfio_set_event_handler
- turned into a void function
- do theqemu_set_fd_handler(*pfd, NULL, NULL, vdev)andevent_notifier_cleanuponVFIO_DEVICE_SET_IRQSfailure as reported by Alexey
- reset err invfio_realizeas reported by Cornelia
- Text/comment fixes suggested by Cornelia--- hw/vfio/pci.c | 296 ++++++++++++++++++++++---------------------------- 1 file changed, 132 insertions(+), 164 deletions(-)hw/vfio/pci.c +0
-0@@ -105,6 +105,96 @@ static void vfio_intx_eoi(VFIODevice *vbasedev)vfio_unmask_single_irqindex (vbasedev,VFIO_PCI_INTX_IRQ_INDEX ); }Quoted 11 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 116
Quoted 9 lines
hw/vfio/pci.c +9
-0+/* +* vfio_set_event_handler - setup/tear down eventfd +* notification and handling for IRQ indices that span over +* a single IRQ +* +* @vdev: VFIO device handle +* @index: IRQ index the eventfd/handler is associated with +* @enable: true means notifier chain needs to be set up +* @handler: handler to attach if @enable is true Therefore @enable is redundant.
agreed
Quoted 18 lines
Quoted 18 lines
hw/vfio/pci.c +17
-0+* @errp: error handle +*/ +static void vfio_set_event_handler (VFIOPCIDevice *vdev, +int index, +bool enable, +void (*handler)(void *opaque), +Error **errp) +{ +struct vfio_irq_info irq_info = { .argsz =sizeof (irq_info), + .index = index }; +struct vfio_irq_set *irq_set; +EventNotifier *notifier; +int argsz, ret =0 ; +int32_t *pfd, fd; + +switch (index) { +case VFIO_PCI_REQ_IRQ_INDEX :Quoted 8 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 138
Quoted 5 lines
hw/vfio/pci.c +5
-0+ notifier = &vdev->req_notifier; +break ; +case VFIO_PCI_ERR_IRQ_INDEX : + notifier = &vdev->err_notifier; +break ;This blows the abstraction of a helper that this seems to be trying to create, seems cleaner to pass @notifier.
Quoted 4 lines
Not sure I really get the point eventually. Don't we have the following
indirection: irq index -> notifier.fd -> handler. When we want to use this helper don't we simply want to associate an handler to a given IRQ index without taking care of the notifier mechanics.
Quoted 6 lines
With that logic we could eliminate all the parameters and have the function infer everything. I don't think that's how we build a good helper function though. To me the function is wanting to set or clear a handler for an irq index, but it also needs the notifier to trigger to call that handler, so we simply need to pass that as another arg rather than inferring it from the index.
OK
Quoted 6 lines
Quoted 3 lines
As discussed with Alexey, moving the notifier initialization outside of this helper removes some code factorization.
I don't see why passing the notifier implies this function cannot perform the init and cleanup of that notifier.
Got it now.
Quoted 14 lines
Quoted 14 lines
Quoted 14 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 146
Quoted 9 lines
hw/vfio/pci.c +8
-0+default : +g_assert_not_reached (); + } + +if (ioctl (vdev->vbasedev.fd, +VFIO_DEVICE_GET_IRQ_INFO , &irq_info) <0 || irq_info.count <1 ) { +error_setg_errno (errp, errno,"No irq index %d available" , index); +return ;The implicit count, aka sub-index, is also problematic for the abstraction. Can we tackle applying this to MSI/X to validate if this needs to go another step to allow the caller to specify index and sub-index?
Quoted 7 lines
Quoted 3 lines
I mentioned the helper stands for IRQ indices with no sub-index. I am afraid applying this to MSI/X would oblige use to revisit a bulk of code without knowing whether it is interesting.
I'm afraid that the helper shows some holes with INTx integration and I'm wondering if MSI/X integration would show us how to improve the helper.
OK I will do the exercise
Quoted 32 lines
Quoted 32 lines
Quoted 32 lines
Quoted 18 lines
hw/vfio/pci.c +17
-0+ } + +if (enable) { + ret =event_notifier_init (notifier,0 ); +if (ret) { +error_setg_errno (errp, -ret, +"Unable to init event notifier for irq index %d" , + index); +return ; + } + } + + argsz =sizeof (*irq_set) +sizeof (*pfd); + + irq_set =g_malloc0 (argsz); + irq_set->argsz = argsz; + irq_set->flags = VFIO_IRQ_SET_DATA_EVENTFD |hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 173
Quoted 10 lines
hw/vfio/pci.c +10
-0+VFIO_IRQ_SET_ACTION_TRIGGER ; + irq_set->index = index; + irq_set->start =0 ; + irq_set->count =1 ; + pfd = (int32_t *)&irq_set->data; + +if (!notifier) { +error_setg (errp,"Notifier not initialized for irq index %d" , index); +return ; + }What is this supposed to check? @notifier is not NULL initialized, the case statement will assert if it doesn't get set, and this doesn't actually test if it's properly initialized.
Quoted 6 lines
Quoted 3 lines
The goal was to check the helper was not called on a valid IRQ index with !enabled while the notifier was not properly initialized. But if we trust the calling sites I can remove it.
But this doesn't test if the notifier is initialized. Seems you'd need to check if fd of the notifier is -1.
I understand the point now
Quoted 245 lines
Quoted 241 lines
Quoted 20 lines
Quoted 20 lines
hw/vfio/pci.c +18
-0+ + fd =event_notifier_get_fd (notifier); + +if (enable) { +qemu_set_fd_handler (fd, handler,NULL , vdev); + *pfd = fd; + }else { + *pfd =-1 ; + } + + ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); +g_free (irq_set); + +if (ret) { +error_setg_errno (errp, -ret, +"Failed to %s eventfd signalling for index %d" , + enable ?"set up" :"tear down" , index); + }Quoted 8 lines
hw/vfio/pci.c static void vfio_intx_eoi(VFIODevice *vbasedev) · line 196
Quoted 5 lines
hw/vfio/pci.c +5
-0+if (ret || !enable) { +qemu_set_fd_handler (fd,NULL ,NULL , vdev); +event_notifier_cleanup (notifier); + } +}Suggest passing @notifier as a parameter and using @handler in place of @enable, more generic and more obvious calling convention.
ok
Quoted 202 lines
Quoted 189 lines
hw/vfio/pci.c +5
-162+static void vfio_intx_enable_kvm (VFIOPCIDevice *vdev,Error **errp) {#ifdef CONFIG_KVM @@ -2621,86 +2711,6 @@ static void vfio_err_notifier_handler(void *opaque)vm_stop (RUN_STATE_INTERNAL_ERROR ); } -/* -* Registers error notifier for devices supporting error recovery. -* If we encounter a failure in this function, we report an error -* and continue after disabling error recovery support for the -* device. -*/ -static void vfio_register_err_notifier (VFIOPCIDevice *vdev) -{ -int ret; -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!vdev->pci_aer) { -return ; - } - -if (event_notifier_init (&vdev->err_notifier,0 )) { -error_report ("vfio: Unable to init event notifier for error detection" ); - vdev->pci_aer = false; -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_ERR_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->err_notifier); -qemu_set_fd_handler (*pfd, vfio_err_notifier_handler,NULL , vdev); - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_report ("vfio: Failed to set up error notification" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->err_notifier); - vdev->pci_aer = false; - } -g_free (irq_set); -} - -static void vfio_unregister_err_notifier (VFIOPCIDevice *vdev) -{ -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; -int ret; - -if (!vdev->pci_aer) { -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_ERR_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - *pfd =-1 ; - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_report ("vfio: Failed to de-assign error fd: %m" ); - } -g_free (irq_set); -qemu_set_fd_handler (event_notifier_get_fd (&vdev->err_notifier), -NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->err_notifier); -} -static void vfio_req_notifier_handler (void *opaque) {VFIOPCIDevice *vdev = opaque;@@ -2716,86 +2726,6 @@ static void vfio_req_notifier_handler(void *opaque) } } -static void vfio_register_req_notifier (VFIOPCIDevice *vdev) -{ -struct vfio_irq_info irq_info = { .argsz =sizeof (irq_info), - .index =VFIO_PCI_REQ_IRQ_INDEX }; -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!(vdev->features &VFIO_FEATURE_ENABLE_REQ )) { -return ; - } - -if (ioctl (vdev->vbasedev.fd, -VFIO_DEVICE_GET_IRQ_INFO , &irq_info) <0 || irq_info.count <1 ) { -return ; - } - -if (event_notifier_init (&vdev->req_notifier,0 )) { -error_report ("vfio: Unable to init event notifier for device request" ); -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_REQ_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->req_notifier); -qemu_set_fd_handler (*pfd, vfio_req_notifier_handler,NULL , vdev); - -if (ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set)) { -error_report ("vfio: Failed to set up device request notification" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->req_notifier); - }else { - vdev->req_enabled = true; - } - -g_free (irq_set); -} - -static void vfio_unregister_req_notifier (VFIOPCIDevice *vdev) -{ -int argsz; -struct vfio_irq_set *irq_set; -int32_t *pfd; - -if (!vdev->req_enabled) { -return ; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD | -VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_REQ_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - *pfd =-1 ; - -if (ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set)) { -error_report ("vfio: Failed to de-assign device request fd: %m" ); - } -g_free (irq_set); -qemu_set_fd_handler (event_notifier_get_fd (&vdev->req_notifier), -NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->req_notifier); - - vdev->req_enabled = false; -} -static void vfio_realize (PCIDevice *pdev,Error **errp) {VFIOPCIDevice *vdev =PCI_VFIO (pdev);@@ -3069,8 +2999,33 @@ static void vfio_realize(PCIDevice *pdev, Error **errp) goto out_teardown; } -vfio_register_err_notifier (vdev); -vfio_register_req_notifier (vdev); +if (vdev->pci_aer) { +Error *err =NULL ; + +/* hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3015
Quoted 10 lines
hw/vfio/pci.c +10
-0+* Registers error notifier for devices supporting error recovery. +* If we encounter a failure during registration, we report an error +* and continue after disabling error recovery support for the +* device. +*/ +vfio_set_event_handler (vdev,VFIO_PCI_ERR_IRQ_INDEX , true, + vfio_err_notifier_handler, &err); +if (err) { +warn_reportf_err (err,VFIO_MSG_PREFIX , vdev->vbasedev.name); + }Why not just return -1 on error and zero on success so we can call as:
Quoted 3 lines
if (vfio_set_event_handler(...)) { warn_reportf_err()... }The point is that if you have both the err and the returned value , it is error prone as you expect both to be consistent (reported by Alexey). You expect err to be set whenever you have a an error returned. The calling site can call
warn_reportf_err()whenever the function returns an error and if somebody, later on, ignores to set the err on error case, it will crash.Quoted 3 lines
Reading again Markus' answer
(https://www.mail-archive.com/[email protected]/msg402893.html), I may put the returned value back and make sure my code is consistent ;-)
Quoted 5 lines
It's not like C programmers aren't used to checking return values. Not exactly analogous, but we check the return value of an
ioctl()then look at errno. So it feels like standard practice to return an error code on failure and try to only use void returns for functions that cannot fail.
ok
Quoted 20 lines
Quoted 14 lines
Quoted 5 lines
hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3016
Quoted 3 lines
hw/vfio/pci.c +1
-0+ vdev->pci_aer = !err;We could also avoid this weirdness of this negation to get a bool.
ok
Quoted 7 lines
hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 3017
Quoted 2 lines
hw/vfio/pci.c +1
-0+ }It's not obvious how doing away with the register/unregister helpers and doing everything inline is an improvement. Simple helpers calling common helpers seems better than inline sprawl calling common helpers. Thanks,
Quoted 5 lines
On my side I noticed vfio_(un)register_err|req_notifier are mostly identical at the exception of the irq index/notifier and enable logic. As I am about to propose another single index IRQ, I am going to add 2 similar functions and I felt it was a pitty. Now it is not a big deal and if you prefer to keep the code as it is I will simply add those.
Quoted 3 lines
Simple helper functions are a good thing IMO, especially with the prospects of open coding two more setup and teardown sections further bloating the base function. Thanks,
Thanks
Eric
Quoted 3 lines
Alex
PATCH v2 2/2 vfio-pci: Use vfio_set_event_handler in vfio_intx_enable
In reply to Eric Augervfio_set_event_handler() can be used in vfio_intx_enable() to set the signalling associated with VFIO_PCI_INTX_IRQ_INDEX.
We also turn vfio_intx_enable() into a void function.
---
vfio_set_event_handler cannot be used in vfio_intx_disable. The reason is not a call sequence issue but the VFIO_DEVICE_SET_IRQS invoction. vfio_disable_irqindex uses ACTION_TRIGGER/DATA_NONE/count==0 whereas the new helper uses ACTION_TRIGGER/DATA_EVENTFD/fd==-1. Surprisingly to me, both are not resulting into the same kernel actions. The first one does a complete tear down of the INTx (vfio_intx_disable), while the second - just taking care of a single index, the only one by the way for INTx -, does an incomplete tear down (vfio_intx_set_signal). If the last one is used, a subsequent setup of MSIx vectors fails.
v1 -> v2:
- turn vfio_intx_enable into a void function
- s/vfio_intx_enable_kvm/vfio_intx_enable in title and commit msg
--- hw/vfio/pci.c | 51 +++++++++++++-------------------------------------- 1 file changed, 13 insertions(+), 38 deletions(-)
hw/vfio/pci.c +13 -38
@@ -136,6 +136,9 @@ static void vfio_set_event_handler(VFIOPCIDevice *vdev,case VFIO_PCI_ERR_IRQ_INDEX : notifier = &vdev->err_notifier;break ; +case VFIO_PCI_INTX_IRQ_INDEX : + notifier = &vdev->intx.interrupt; +break ;default :g_assert_not_reached (); }
@@ -349,16 +352,13 @@ static void vfio_intx_update(PCIDevice *pdev)vfio_intx_eoi (&vdev->vbasedev); } -static int vfio_intx_enable (VFIOPCIDevice *vdev,Error **errp) +static void vfio_intx_enable (VFIOPCIDevice *vdev,Error **errp) {uint8_t pin =vfio_pci_read_config (&vdev->pdev,PCI_INTERRUPT_PIN ,1 ); -int ret, argsz, retval =0 ; -struct vfio_irq_set *irq_set; -int32_t *pfd;Error *err =NULL ;if (!pin) { -return 0 ; +return ; }vfio_disable_interrupts (vdev);
@@ -377,32 +377,11 @@ static int vfio_intx_enable(VFIOPCIDevice *vdev, Error **errp) }#endif - ret =event_notifier_init (&vdev->intx.interrupt,0 ); -if (ret) { -error_setg_errno (errp, -ret,"event_notifier_init failed" ); -return ret; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD |VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_INTX_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->intx.interrupt); -qemu_set_fd_handler (*pfd, vfio_intx_interrupt,NULL , vdev); - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_setg_errno (errp, -ret,"failed to setup INTx fd" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->intx.interrupt); - retval = -errno; - goto cleanup; +vfio_set_event_handler (vdev,VFIO_PCI_INTX_IRQ_INDEX , true, + vfio_intx_interrupt, &err); +if (err) { +error_propagate (errp, err); +return ; }vfio_intx_enable_kvm (vdev, &err);
@@ -413,11 +392,6 @@ static int vfio_intx_enable(VFIOPCIDevice *vdev, Error **errp) vdev->interrupt = VFIO_INT_INTx;trace_vfio_intx_enable (vdev->vbasedev.name); - -cleanup: -g_free (irq_set); - -return retval; }static void vfio_intx_disable (VFIOPCIDevice *vdev)
@@ -2982,8 +2956,9 @@ static void vfio_realize(PCIDevice *pdev, Error **errp) vdev->intx.mmap_timer =timer_new_ms (QEMU_CLOCK_VIRTUAL , vfio_intx_mmap_enable, vdev);pci_device_set_intx_routing_notifier (&vdev->pdev, vfio_intx_update); - ret =vfio_intx_enable (vdev, errp); -if (ret) { +vfio_intx_enable (vdev, &err); +if (err) { +error_propagate (errp, err); goto out_teardown; } }
Signature · 1 line
2.20.1
Re: [Qemu-devel] [PATCH v2 2/2] vfio-pci: Use vfio_set_event_handler in vfio_intx_enable
Quoted 4 lines · On Thu, 17 Jan 2019 22:06:32 +0100 Eric Auger <[email protected]> wrote:
vfio_set_event_handler()can be used invfio_intx_enable()to set the signalling associated withVFIO_PCI_INTX_IRQ_INDEX.We also turn
vfio_intx_enable()into a void function.
Why?
Quoted 4 lines
Signed-off-by Eric Auger <[email protected]>---
Quoted 9 lines
vfio_set_event_handlercannot be used invfio_intx_disable. The reason is not a call sequence issue but theVFIO_DEVICE_SET_IRQSinvoction.vfio_disable_irqindexuses ACTION_TRIGGER/DATA_NONE/count==0 whereas the new helper uses ACTION_TRIGGER/DATA_EVENTFD/fd==-1. Surprisingly to me, both are not resulting into the same kernel actions. The first one does a complete tear down of the INTx (vfio_intx_disable), while the second - just taking care of a single index, the only one by the way for INTx -, does an incomplete tear down (vfio_intx_set_signal). If the last one is used, a subsequent setup of MSIx vectors fails.
As we discussed offline, this is documented in the uapi and reflects that the device can be in an interrupt mode without any signaling vectors. For instance the MSI or MSI-X capability on a PCI device can be enabled, but no vectors are configured to signal. It's a bit of an after thought how we enter this mode (see vfio_msix_enable), but it has proven useful. If INTx is going to use the helper for setup but not teardown there at least needs to be a comment in the code indicating the limitation so that an unwitting contributor doesn't fall for the seemingly obvious simplification.
Quoted 13 lines
v1 -> v2:
- turnvfio_intx_enableinto a void function
- s/vfio_intx_enable_kvm/vfio_intx_enable in title and commit msg--- hw/vfio/pci.c | 51 +++++++++++++-------------------------------------- 1 file changed, 13 insertions(+), 38 deletions(-)hw/vfio/pci.c +0
-0
hw/vfio/pci.c static void vfio_set_event_handler(VFIOPCIDevice *vdev, · line 141
Quoted 6 lines
hw/vfio/pci.c +3
-0@@ -136,6 +136,9 @@ static void vfio_set_event_handler(VFIOPCIDevice *vdev,case VFIO_PCI_ERR_IRQ_INDEX : notifier = &vdev->err_notifier;break ; +case VFIO_PCI_INTX_IRQ_INDEX : + notifier = &vdev->intx.interrupt; +break ;
I'm still not a fan of a helper than needs to be updated for each new caller.
Quoted 73 lines
hw/vfio/pci.c +7
-36default :g_assert_not_reached (); }@@ -349,16 +352,13 @@ static void vfio_intx_update(PCIDevice *pdev)vfio_intx_eoi (&vdev->vbasedev); } -static int vfio_intx_enable (VFIOPCIDevice *vdev,Error **errp) +static void vfio_intx_enable (VFIOPCIDevice *vdev,Error **errp) {uint8_t pin =vfio_pci_read_config (&vdev->pdev,PCI_INTERRUPT_PIN ,1 ); -int ret, argsz, retval =0 ; -struct vfio_irq_set *irq_set; -int32_t *pfd;Error *err =NULL ;if (!pin) { -return 0 ; +return ; }vfio_disable_interrupts (vdev);@@ -377,32 +377,11 @@ static int vfio_intx_enable(VFIOPCIDevice *vdev, Error **errp) }#endif - ret =event_notifier_init (&vdev->intx.interrupt,0 ); -if (ret) { -error_setg_errno (errp, -ret,"event_notifier_init failed" ); -return ret; - } - - argsz =sizeof (*irq_set) +sizeof (*pfd); - - irq_set =g_malloc0 (argsz); - irq_set->argsz = argsz; - irq_set->flags =VFIO_IRQ_SET_DATA_EVENTFD |VFIO_IRQ_SET_ACTION_TRIGGER ; - irq_set->index =VFIO_PCI_INTX_IRQ_INDEX ; - irq_set->start =0 ; - irq_set->count =1 ; - pfd = (int32_t *)&irq_set->data; - - *pfd =event_notifier_get_fd (&vdev->intx.interrupt); -qemu_set_fd_handler (*pfd, vfio_intx_interrupt,NULL , vdev); - - ret =ioctl (vdev->vbasedev.fd,VFIO_DEVICE_SET_IRQS , irq_set); -if (ret) { -error_setg_errno (errp, -ret,"failed to setup INTx fd" ); -qemu_set_fd_handler (*pfd,NULL ,NULL , vdev); -event_notifier_cleanup (&vdev->intx.interrupt); - retval = -errno; - goto cleanup; +vfio_set_event_handler (vdev,VFIO_PCI_INTX_IRQ_INDEX , true, + vfio_intx_interrupt, &err); +if (err) { +error_propagate (errp, err); +return ; }vfio_intx_enable_kvm (vdev, &err);@@ -413,11 +392,6 @@ static int vfio_intx_enable(VFIOPCIDevice *vdev, Error **errp) vdev->interrupt = VFIO_INT_INTx;trace_vfio_intx_enable (vdev->vbasedev.name); - -cleanup: -g_free (irq_set); - -return retval; }static void vfio_intx_disable (VFIOPCIDevice *vdev)
hw/vfio/pci.c static void vfio_realize(PCIDevice *pdev, Error **errp) · line 2961
Quoted 8 lines
hw/vfio/pci.c +3
-2@@ -2982,8 +2956,9 @@ static void vfio_realize(PCIDevice *pdev, Error **errp) vdev->intx.mmap_timer =timer_new_ms (QEMU_CLOCK_VIRTUAL , vfio_intx_mmap_enable, vdev);pci_device_set_intx_routing_notifier (&vdev->pdev, vfio_intx_update); - ret =vfio_intx_enable (vdev, errp); -if (ret) { +vfio_intx_enable (vdev, &err); +if (err) { +error_propagate (errp, err);
Wouldn't it still be easier to return -1/0 rather than test err? I'm not sure what was gained with the conversion to void. Thanks,
Alex
Quoted 3 lines
hw/vfio/pci.c +0
-0goto out_teardown; } }