Stratix10 EDAC Improvements
Subsystems (5)
v2 cover Stratix10 EDAC Improvements
From: Thor Thayer <[email protected]>
This patch series includes a fix, an improvement and the addition of OCRAM EDAC for Stratix10 SOCFPGA.
V2: Ensure the Fixes: line is on one line.
Thor Thayer (4):
EDAC, altera: Fix S10 persistent register offset EDAC, altera: Less Intrusive Error Injection EDAC, altera: Add Stratix10 OCRAM ECC support
arm64: dts: stratix10: Add OCRAM EDAC node
arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi | 7 +++ drivers/edac/altera_edac.c | 52 ++++++++++++++--------- drivers/edac/altera_edac.h | 6 +-- 3 files changed, 43 insertions(+), 22 deletions(-)
Signature · 1 line
2.7.4
PATCH v2 1/4 EDAC, altera: Fix S10 persistent register offset
From: Thor Thayer <[email protected]>
Correct the persistent register offset where address and status are stored.
---
v2 Fixes tag should be on one line instead of wrapped.
--- drivers/edac/altera_edac.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/edac/altera_edac.h +2 -2
@@ -295,8 +295,8 @@ struct altr_sdram_mc_data {#define S10_SYSMGR_ECC_INTSTAT_DERR_OFST 0xA0/* Sticky registers for Uncorrected Errors */ -#define S10_SYSMGR_UE_VAL_OFST 0x120 -#define S10_SYSMGR_UE_ADDR_OFST 0x124 +#define S10_SYSMGR_UE_VAL_OFST 0x220 +#define S10_SYSMGR_UE_ADDR_OFST 0x224#define S10_DDR0_IRQ_MASK BIT(16)
Signature · 1 line
2.7.4
PATCH v2 2/4 EDAC, altera: Less Intrusive Error Injection
In reply to [email protected]From: Thor Thayer <[email protected]>
Improve the Arria10 and Stratix10 error injection routines by reading the data and changing just 1 bit before writing back out. Previous routine would set the first bytes to 0 then change to 1 but this method is less intrusive.
---
v2 No Changes
--- drivers/edac/altera_edac.c | 30 +++++++++++++----------------- drivers/edac/altera_edac.h | 2 +- 2 files changed, 14 insertions(+), 18 deletions(-)
drivers/edac/altera_edac.c +13 -17
@@ -1756,28 +1756,24 @@ static ssize_t altr_edac_a10_device_trig2(struct file *file,if (trig_type ==ALTR_UE_TRIGGER_CHAR ) {writel (priv->ue_set_mask, set_addr); }else { -/* Setup write of 0 to first 4 bytes */ -writel (0x0 , drvdata->base +ECC_BLK_WDATA0_OFST ); -writel (0x0 , drvdata->base +ECC_BLK_WDATA1_OFST ); -writel (0x0 , drvdata->base +ECC_BLK_WDATA2_OFST ); -writel (0x0 , drvdata->base +ECC_BLK_WDATA3_OFST ); -/* Setup write of 4 bytes */ +/* Setup read/write of 4 bytes */ writel (ECC_WORD_WRITE , drvdata->base +ECC_BLK_DBYTECTRL_OFST );/* Setup Address to 0 */ -writel (0x0 , drvdata->base +ECC_BLK_ADDRESS_OFST ); -/* Setup accctrl to write & data override */ -writel (ECC_WRITE_DOVR , drvdata->base +ECC_BLK_ACCCTRL_OFST ); -/* Kick it. */ -writel (ECC_XACT_KICK , drvdata->base +ECC_BLK_STARTACC_OFST ); -/* Setup accctrl to read & ecc override */ -writel (ECC_READ_EOVR , drvdata->base +ECC_BLK_ACCCTRL_OFST ); +writel (0 , drvdata->base +ECC_BLK_ADDRESS_OFST ); +/* Setup accctrl to read & ecc & data override */ +writel (ECC_READ_EDOVR , drvdata->base +ECC_BLK_ACCCTRL_OFST );/* Kick it. */ writel (ECC_XACT_KICK , drvdata->base +ECC_BLK_STARTACC_OFST );/* Setup write for single bit change */ -writel (0x1 , drvdata->base +ECC_BLK_WDATA0_OFST ); -writel (0x0 , drvdata->base +ECC_BLK_WDATA1_OFST ); -writel (0x0 , drvdata->base +ECC_BLK_WDATA2_OFST ); -writel (0x0 , drvdata->base +ECC_BLK_WDATA3_OFST ); +writel (readl (drvdata->base +ECC_BLK_RDATA0_OFST ) ^0x1 , + drvdata->base +ECC_BLK_WDATA0_OFST ); +writel (readl (drvdata->base +ECC_BLK_RDATA1_OFST ), + drvdata->base +ECC_BLK_WDATA1_OFST ); +writel (readl (drvdata->base +ECC_BLK_RDATA2_OFST ), + drvdata->base +ECC_BLK_WDATA2_OFST ); +writel (readl (drvdata->base +ECC_BLK_RDATA3_OFST ), + drvdata->base +ECC_BLK_WDATA3_OFST ); +/* Copy Read ECC to Write ECC */ writel (readl (drvdata->base +ECC_BLK_RECC0_OFST ), drvdata->base +ECC_BLK_WECC0_OFST );
drivers/edac/altera_edac.h +1 -1
@@ -319,7 +319,7 @@ struct altr_sdram_mc_data {#define ECC_BLK_STARTACC_OFST 0x7C#define ECC_XACT_KICK 0x10000 -#define ECC_WORD_WRITE 0xF +#define ECC_WORD_WRITE 0xFF#define ECC_WRITE_DOVR 0x101#define ECC_WRITE_EDOVR 0x103#define ECC_READ_EOVR 0x2
Signature · 1 line
2.7.4
PATCH v2 3/4 EDAC, altera: Add Stratix10 OCRAM ECC support
In reply to [email protected]From: Thor Thayer <[email protected]>
Use the newer ECC error injection method for Arria10 and Stratix10 OCRAM.
OCRAM can't call the common peripheral init routine since OCRAM is being used. An OCRAM specific init routine ensures the OCRAM ECC is setup without clearing memory.
---
v2 No changes
--- drivers/edac/altera_edac.c | 22 ++++++++++++++++++++-- 1 file changed, 20 insertions(+), 2 deletions(-)
drivers/edac/altera_edac.c +20 -2
@@ -1216,8 +1216,26 @@ static const struct edac_device_prv_data ocramecc_data = { .inject_fops = &altr_edac_device_inject_fops, }; +static int __maybe_unused +altr_a10_check_ecc_deps_init (struct altr_edac_device_dev *device) +{ +void __iomem *base = device->base; +int ret; + + ret =altr_check_ecc_deps (device); +if (ret) +return ret; + +/* Enable IRQ on Single Bit Error */ +writel (ALTR_A10_ECC_SERRINTEN , (base +ALTR_A10_ECC_ERRINTENS_OFST )); +/* Ensure all writes complete */ +wmb (); + +return 0 ; +} +static const struct edac_device_prv_data a10_ocramecc_data = { - .setup = altr_check_ecc_deps, + .setup = altr_a10_check_ecc_deps_init, .ce_clear_mask =ALTR_A10_ECC_SERRPENA , .ue_clear_mask =ALTR_A10_ECC_DERRPENA , .irq_status_mask =A10_SYSMGR_ECC_INTSTAT_OCRAM ,
@@ -1227,7 +1245,7 @@ static const struct edac_device_prv_data a10_ocramecc_data = { .ue_set_mask = ALTR_A10_ECC_TDERRA, .set_err_ofst = ALTR_A10_ECC_INTTEST_OFST, .ecc_irq_handler = altr_edac_a10_ecc_irq, - .inject_fops = &altr_edac_a10_device_inject_fops, + .inject_fops = &altr_edac_a10_device_inject2_fops,/* * OCRAM panic on uncorrectable error because sleep/resume * functions and FPGA contents are stored in OCRAM. Prefer
Signature · 1 line
2.7.4
PATCH v2 4/4 arm64: dts: stratix10: Add OCRAM EDAC node
In reply to [email protected]From: Thor Thayer <[email protected]>
Add the OCRAM ECC node following the Arria10 format.
---
v2 No changes
--- arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi +7 -0
@@ -494,6 +494,13 @@ interrupts = <16 4>, <48 4>; }; + ocram-ecc@ff8cc000 { + compatible = "altr,socfpga-a10-ocram-ecc"; + reg = <0xff8cc000 0x100>; + interrupts = <1 4>, + <33 4>; + }; + usb0-ecc@ff8c4000 { compatible = "altr,socfpga-usb-ecc"; reg = <0xff8c4000 0x100>;
Signature · 1 line
2.7.4
Dinh Nguyen
maintainerRe: [PATCHv2 4/4] arm64: dts: stratix10: Add OCRAM EDAC node
Quoted 16 lines · On 1/22/19 11:48 AM, [email protected] wrote:
From: Thor Thayer <[email protected]>
Add the OCRAM ECC node following the Arria10 format.
Signed-off-by Thor Thayer <[email protected]>---
v2 No changes--- arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi | 7 +++++++ 1 file changed, 7 insertions(+)arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi +0
-0
arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi line 498
Quoted 5 lines
arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi +2
-0@@ -494,6 +494,13 @@ interrupts = <16 4>, <48 4>; }; + ocram-ecc@ff8cc000 { + compatible = "altr,socfpga-a10-ocram-ecc";
Are you absolutely sure there are no differences in the Stratix10 versus A10? I wonder if it would be safer to have a platform specific binding for Stratix10 rather than re-using A10. It would prevent from having to change bindings later.
Dinh
Re: [PATCHv2 4/4] arm64: dts: stratix10: Add OCRAM EDAC node
Quoted 30 lines · Dinh Nguyen
Quoted 16 lines · On 1/22/19 11:48 AM, [email protected] wrote:
From: Thor Thayer <[email protected]>
Add the OCRAM ECC node following the Arria10 format.
Signed-off-by Thor Thayer <[email protected]>---
v2 No changes--- arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi | 7 +++++++ 1 file changed, 7 insertions(+)arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi +0
-0arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi line 498
Quoted 5 lines
arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi +2
-0@@ -494,6 +494,13 @@ interrupts = <16 4>, <48 4>; }; + ocram-ecc@ff8cc000 { + compatible = "altr,socfpga-a10-ocram-ecc";Are you absolutely sure there are no differences in the Stratix10 versus A10? I wonder if it would be safer to have a platform specific binding for Stratix10 rather than re-using A10. It would prevent from having to change bindings later.
Quoted 2 lines
Dinh
They are the same functionally. However, you bring up a good point. There are differences related to the underlying architecture - 32bit vs 64bit.
I will respin this series (except for the first fixup patch) with new bindings for S10.
Thanks,
Thor
Borislav Petkov
maintainerQuoted 13 lines · On Tue, Jan 22, 2019 at 11:48:03AM -0600, [email protected] wrote:
From: Thor Thayer <[email protected]>
This patch series includes a fix, an improvement and the addition of OCRAM EDAC for Stratix10 SOCFPGA.
V2: Ensure the Fixes: line is on one line.
Thor Thayer (4):
EDAC, altera: Fix S10 persistent register offset EDAC, altera: Less Intrusive Error Injection EDAC, altera: Add Stratix10 OCRAM ECC support
arm64: dts: stratix10: Add OCRAM EDAC node
Quoted 4 lines
arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi | 7 +++ drivers/edac/altera_edac.c | 52 ++++++++++++++--------- drivers/edac/altera_edac.h | 6 +-- 3 files changed, 43 insertions(+), 22 deletions(-)
Looks ok, I'll take them when I get an ACK for the DT change in patch 4.
Patch 1 I'll send to Linus now as the broken commit is in 4.20 too.
Signature · 4 lines
Regards/Gruss,
Boris.
Good mailing practices for 400: avoid top-posting and trim the reply.