Skip to contentSkip to conversation

AM65x: Add DMA support

PATCH Superseded Vignesh R 2 participants 14 messages Jan 29, 2019 – Feb 1, 2019

Subsystems (8)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore

Vignesh R

author maintainer
#0 lore raw

v3 cover AM65x: Add DMA support

This series adds DMA support for TI's AM654 SoC.

v3:
Minor comment/whitespace cleanups as pointed out by Tom Rini

v2:
Align DT bindings with latest proposed bindings as pointed out by Peter. Merge drivers/soc/keystone into drivers/soc/ti

Background:

The AM65x TRM (http://www.ti.com/lit/pdf/spruid7b) describes the Data Movement Architecture which is implmented by the k3-udma driver.

This DMA architecture is a big departure from 'traditional' architecture where we had either EDMA or sDMA as system DMA.

Packet DMAs were used as dedicated DMAs to service only networking (K2) or USB (am335x) while other peripherals were serviced by EDMA.

In AM65x the UDMA (Unified DMA) is used for all data movment within the SoC, tasked to service all peripherals (UART, McSPI, McASP, networking, etc).

The NAVSS/UDMA is built around CPPI5 (Communications Port Programming Interface) and it supports Packet mode (similar to CPPI4.1 in K2 for networking) and TR mode (similar to EDMA descriptor).
The data movement is done within a PSI-L fabric, all peripherals (including the UDMA-P). peripherals are not addressed by their I/O register as with traditional DMAs but with their PSI-L thread ID.

To be able to use the DMA the following generic steps need to be taken:
- configure a DMA channel (tchan for TX, rchan for RX)
- channel mode: Packet or TR mode
- for memcpy a tchan and rchan pair is used.
- for packet mode RX we also need to configure a receive flow to configure the packet receiption
- the source and destination threads must be paired
- at minimum one pair of rings need to be configured:
- tx: transfer ring and transfer completion ring
- rx: free descriptor ring and receive ring

When the channel setup is completed we only interract with the rings:
- TX: push a descriptor to t_ring and wait for it to be pushed to the tc_ring by the UDMA-P
- RX: push a descriptor to the fd_ring and wait for UDMA-P to push it back to the r_ring.

Resources Management and configuration of channel and ring is handled by sending TI-SCI msgs to remote core.

Patches are based on kernel patches here:
https://patchwork.kernel.org/cover/10612465/

Grygorii Strashko (5):
firmware: ti_sci: Add support for NAVSS resource management
soc: ti: k3: add navss ringacc driver
soc: ti: k3: add CPPI5 description and helpers
arm64: dts: ti: k3-am65: add mcu navss nodes
configs: am65x_evm_a53: Enable DMA related configs

Vignesh R (2):
dma: ti: add driver to K3 UDMA
soc: keystone: Merge into ti specific directory

 arch/arm/dts/k3-am65-wakeup.dtsi              |    2 +-
 arch/arm/dts/k3-am654-base-board-u-boot.dtsi  |   46 +
 arch/arm/mach-keystone/Kconfig                |    8 +
 configs/am65x_evm_a53_defconfig               |    4 +-
 drivers/Kconfig                               |    2 +
 drivers/dma/Kconfig                           |    2 +
 drivers/dma/Makefile                          |    2 +
 drivers/dma/ti/Kconfig                        |   14 +
 drivers/dma/ti/Makefile                       |    3 +
 drivers/dma/ti/k3-udma-hwdef.h                |  184 ++
 drivers/dma/ti/k3-udma.c                      | 1737 +++++++++++++++++
 drivers/firmware/ti_sci.c                     |  760 +++++++-
 drivers/firmware/ti_sci.h                     |  642 ++++++
 drivers/soc/Kconfig                           |    5 +
 drivers/soc/Makefile                          |    2 +-
 drivers/soc/keystone/Makefile                 |    3 -
 drivers/soc/ti/Kconfig                        |   26 +
 drivers/soc/ti/Makefile                       |    4 +
 drivers/soc/ti/k3-navss-ringacc.c             | 1096 +++++++++++
 .../soc/{keystone => ti}/keystone_serdes.c    |    0
 include/configs/ti_armv7_keystone2.h          |    3 -
 include/dt-bindings/dma/k3-udma.h             |   31 +
 include/linux/soc/ti/cppi5.h                  |  995 ++++++++++
 include/linux/soc/ti/k3-navss-ringacc.h       |  246 +++
 include/linux/soc/ti/ti-udma.h                |   24 +
 include/linux/soc/ti/ti_sci_protocol.h        |  300 +++
 scripts/config_whitelist.txt                  |    1 -
 27 files changed, 6121 insertions(+), 21 deletions(-)
 create mode 100644 drivers/dma/ti/Kconfig
 create mode 100644 drivers/dma/ti/Makefile
 create mode 100644 drivers/dma/ti/k3-udma-hwdef.h
 create mode 100644 drivers/dma/ti/k3-udma.c
 create mode 100644 drivers/soc/Kconfig
 delete mode 100644 drivers/soc/keystone/Makefile
 create mode 100644 drivers/soc/ti/Kconfig
 create mode 100644 drivers/soc/ti/Makefile
 create mode 100644 drivers/soc/ti/k3-navss-ringacc.c
 rename drivers/soc/{keystone => ti}/keystone_serdes.c (100%)
 create mode 100644 include/dt-bindings/dma/k3-udma.h
 create mode 100644 include/linux/soc/ti/cppi5.h
 create mode 100644 include/linux/soc/ti/k3-navss-ringacc.h
 create mode 100644 include/linux/soc/ti/ti-udma.h
Signature · 1 line
2.20.1
author maintainer
#1 lore raw

PATCH v3 1/7 firmware: ti_sci: Add support for NAVSS resource management

From: Grygorii Strashko <[email protected]>

Texas Instruments' System Control Interface (TI-SCI) Message Protocol abstracts management of NAVSS resources, like PSI-L pairing and unpairing, UDMAP tx/rx/flow configuration and Rings.

This patch adds support for requesting and configuring such resources from TI-SCI firmware.

---
 arch/arm/dts/k3-am65-wakeup.dtsi       |   2 +-
 drivers/firmware/ti_sci.c              | 760 ++++++++++++++++++++++++-
 drivers/firmware/ti_sci.h              | 642 +++++++++++++++++++++
 include/linux/soc/ti/ti_sci_protocol.h | 300 ++++++++++
 4 files changed, 1692 insertions(+), 12 deletions(-)
arch/arm/dts/k3-am65-wakeup.dtsi +1 -1
index 8d7b47f9dfbf..1f591ef8bb9e 100644
@@ -7,7 +7,7 @@
 
 &cbass_wakeup {
 	dmsc: dmsc {
-		compatible = "ti,k2g-sci";
+		compatible = "ti,am654-sci";
 		ti,host-id = <12>;
 		#address-cells = <1>;
 		#size-cells = <1>;
drivers/firmware/ti_sci.c +749 -11

833 lines not on this page · raw message

drivers/firmware/ti_sci.h +642 -0

658 lines not on this page · raw message

include/linux/soc/ti/ti_sci_protocol.h +300 -0

342 lines not on this page · raw message

Signature · 1 line
2.20.1
author maintainer
#2 lore raw

PATCH v3 2/7 soc: ti: k3: add navss ringacc driver

In reply to Vignesh R

From: Grygorii Strashko <[email protected]>

The Ring Accelerator (RINGACC or RA) provides hardware acceleration to enable straightforward passing of work between a producer and a consumer. There is one RINGACC module per NAVSS on TI AM65x SoCs.

The RINGACC converts constant-address read and write accesses to equivalent read or write accesses to a circular data structure in memory. The RINGACC eliminates the need for each DMA controller which needs to access ring elements from having to know the current state of the ring (base address, current offset). The DMA controller performs a read or write access to a specific address range (which maps to the source interface on the RINGACC) and the RINGACC replaces the address for the transaction with a new address which corresponds to the head or tail element of the ring (head for reads, tail for writes). Since the RINGACC maintains the state, multiple DMA controllers or channels are allowed to coherently share the same rings as applicable. The RINGACC is able to place data which is destined towards software into cached memory directly.

Supported ring modes:
- Ring Mode
- Messaging Mode
- Credentials Mode
- Queue Manager Mode

TI-SCI integration:

Texas Instrument's System Control Interface (TI-SCI) Message Protocol now has control over Ringacc module resources management (RM) and Rings configuration.

The Ringacc driver manages Rings allocation by itself now and requests TI-SCI firmware to allocate and configure specific Rings only. It's done this way because, Linux driver implements two stage Rings allocation and configuration (allocate ring and configure ring) while TI-SCI Message Protocol supports only one combined operation (allocate+configure).

---
 drivers/Kconfig                         |    2 +
 drivers/soc/Kconfig                     |    5 +
 drivers/soc/Makefile                    |    1 +
 drivers/soc/ti/Kconfig                  |   20 +
 drivers/soc/ti/Makefile                 |    5 +
 drivers/soc/ti/k3-navss-ringacc.c       | 1096 +++++++++++++++++++++++
 include/linux/soc/ti/k3-navss-ringacc.h |  246 +++++
 7 files changed, 1375 insertions(+)
 create mode 100644 drivers/soc/Kconfig
 create mode 100644 drivers/soc/ti/Kconfig
 create mode 100644 drivers/soc/ti/Makefile
 create mode 100644 drivers/soc/ti/k3-navss-ringacc.c
 create mode 100644 include/linux/soc/ti/k3-navss-ringacc.h
drivers/Kconfig +2 -0
index e9fbadd13d5a..1eedb3462b0a 100644
@@ -96,6 +96,8 @@ source "drivers/smem/Kconfig"
 
 source "drivers/sound/Kconfig"
 
+source "drivers/soc/Kconfig"
+
 source "drivers/spi/Kconfig"
 
 source "drivers/spmi/Kconfig"
drivers/soc/Kconfig new file +5 -0
new file mode 100644
index 000000000000..7b4e4d613088
@@ -0,0 +1,5 @@
+menu "SOC (System On Chip) specific Drivers"
+
+source "drivers/soc/ti/Kconfig"
+
+endmenu
drivers/soc/Makefile +1 -0
index 42037f99d587..8b7ead546e1c 100644
@@ -3,3 +3,4 @@
 # Makefile for the U-Boot SOC specific device drivers.
 
 obj-$(CONFIG_ARCH_KEYSTONE)	+= keystone/
+obj-$(CONFIG_SOC_TI) += ti/
drivers/soc/ti/Kconfig new file +20 -0
new file mode 100644
index 000000000000..8c0f3c07b23f
@@ -0,0 +1,20 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+menuconfig SOC_TI
+	bool "TI SOC drivers support"
+
+if SOC_TI
+
+config TI_K3_NAVSS_RINGACC
+	bool "K3 Ring accelerator Sub System"
+	depends on ARCH_K3
+	select MISC
+	help
+	  Say y here to support the K3 AM65x Ring accelerator module.
+	  The Ring Accelerator (RINGACC or RA)  provides hardware acceleration
+	  to enable straightforward passing of work between a producer
+	  and a consumer. There is one RINGACC module per NAVSS on TI AM65x SoCs
+	  If unsure, say N.
+
+
+endif # SOC_TI
drivers/soc/ti/Makefile new file +5 -0
new file mode 100644
index 000000000000..63e21aaad40f
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# TI K3 SOC drivers
+#
+obj-$(CONFIG_TI_K3_NAVSS_RINGACC)	+= k3-navss-ringacc.o
drivers/soc/ti/k3-navss-ringacc.c new file +1096 -0

1,096 lines not on this page · raw message

include/linux/soc/ti/k3-navss-ringacc.h new file +246 -0

246 lines not on this page · raw message

Signature · 1 line
2.20.1
#3 lore raw

PATCH v3 2/7 soc: ti: k3: add navss ringacc driver

Quoted 53 lines · Vignesh R

From: Grygorii Strashko <[email protected]>

The Ring Accelerator (RINGACC or RA) provides hardware acceleration to enable straightforward passing of work between a producer and a consumer. There is one RINGACC module per NAVSS on TI AM65x SoCs.

The RINGACC converts constant-address read and write accesses to equivalent read or write accesses to a circular data structure in memory. The RINGACC eliminates the need for each DMA controller which needs to access ring elements from having to know the current state of the ring (base address, current offset). The DMA controller performs a read or write access to a specific address range (which maps to the source interface on the RINGACC) and the RINGACC replaces the address for the transaction with a new address which corresponds to the head or tail element of the ring (head for reads, tail for writes). Since the RINGACC maintains the state, multiple DMA controllers or channels are allowed to coherently share the same rings as applicable. The RINGACC is able to place data which is destined towards software into cached memory directly.

Supported ring modes:
- Ring Mode
- Messaging Mode
- Credentials Mode
- Queue Manager Mode

TI-SCI integration:

Texas Instrument's System Control Interface (TI-SCI) Message Protocol now has control over Ringacc module resources management (RM) and Rings configuration.

The Ringacc driver manages Rings allocation by itself now and requests TI-SCI firmware to allocate and configure specific Rings only. It's done this way because, Linux driver implements two stage Rings allocation and configuration (allocate ring and configure ring) while TI-SCI Message Protocol supports only one combined operation (allocate+configure).

---
 drivers/Kconfig                         |    2 +
 drivers/soc/Kconfig                     |    5 +
 drivers/soc/Makefile                    |    1 +
 drivers/soc/ti/Kconfig                  |   20 +
 drivers/soc/ti/Makefile                 |    5 +
 drivers/soc/ti/k3-navss-ringacc.c       | 1096 +++++++++++++++++++++++
 include/linux/soc/ti/k3-navss-ringacc.h |  246 +++++
 7 files changed, 1375 insertions(+)
 create mode 100644 drivers/soc/Kconfig
 create mode 100644 drivers/soc/ti/Kconfig
 create mode 100644 drivers/soc/ti/Makefile
 create mode 100644 drivers/soc/ti/k3-navss-ringacc.c
 create mode 100644 include/linux/soc/ti/k3-navss-ringacc.h

[snip]

Quoted 7 lines
drivers/soc/ti/k3-navss-ringacc.c new file +7 -0
+#ifdef DEBUG
+#define	k3_nav_dbg(dev, arg...) dev_err(dev, arg)
+static	void dbg_writel(u32 v, void __iomem *reg)
+{
+	pr_err("WRITEL(32): v(%08X)-->reg(%p)\n", v, reg);
+	writel(v, reg);
+}

drivers/soc/ti/k3-navss-ringacc.c line 52

Quoted 10 lines
drivers/soc/ti/k3-navss-ringacc.c new file +10 -0
+
+static	u32 dbg_readl(void __iomem *reg)
+{
+	u32 v;
+
+	v = readl(reg);
+	pr_err("READL(32): v(%08X)<--reg(%p)\n", v, reg);
+	return v;
+}
+#else

No more new debug macros / functions please. If it's worth having in the driver now that it's being submitted it's worth using the right level of pr_xxx directly, or not having at all. Thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190201/7bc3d57b/attachment.sig>
author maintainer
#4 lore raw

PATCH v3 3/7 soc: ti: k3: add CPPI5 description and helpers

In reply to Vignesh R

From: Grygorii Strashko <[email protected]>

Add TI Communications Port Programming Interface (CPPI) 5 interface description and helpers

---
 include/linux/soc/ti/cppi5.h | 995 +++++++++++++++++++++++++++++++++++
 1 file changed, 995 insertions(+)
 create mode 100644 include/linux/soc/ti/cppi5.h
include/linux/soc/ti/cppi5.h new file +995 -0
new file mode 100644
index 000000000000..34038b31f702
@@ -0,0 +1,995 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * CPPI5 descriptors interface
+ *
+ * Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com
+ */
+
+#ifndef __TI_CPPI5_H__
+#define __TI_CPPI5_H__
+
+#include <hexdump.h>
+#include <linux/bitops.h>
+
+/**
+ * Descriptor header, present in all types of descriptors
+ */
+struct cppi5_desc_hdr_t {
+	u32 pkt_info0;	/* Packet info word 0 (n/a in Buffer desc) */
+	u32 pkt_info1;	/* Packet info word 1 (n/a in Buffer desc) */
+	u32 pkt_info2;	/* Packet info word 2 Buffer reclamation info */
+	u32 src_dst_tag; /* Packet info word 3 (n/a in Buffer desc) */
+} __packed;
+
+/**
+ * Host-mode packet and buffer descriptor definition
+ */
+struct cppi5_host_desc_t {
+	struct cppi5_desc_hdr_t hdr;
+	u64 next_desc;	/* w4/5: Linking word */
+	u64 buf_ptr;	/* w6/7: Buffer pointer */
+	u32 buf_info1;	/* w8: Buffer valid data length */
+	u32 org_buf_len; /* w9: Original buffer length */
+	u64 org_buf_ptr; /* w10/11: Original buffer pointer */
+	u32 epib[0];	/* Extended Packet Info Data (optional, 4 words) */
+	/*
+	 * Protocol Specific Data (optional, 0-128 bytes in multiples of 4),
+	 * and/or Other Software Data (0-N bytes, optional)
+	 */
+} __packed;
+
+#define CPPI5_DESC_MIN_ALIGN			(16U)
+
+#define CPPI5_INFO0_HDESC_EPIB_SIZE		(16U)
+#define CPPI5_INFO0_HDESC_PSDATA_MAX_SIZE	(128U)
+
+#define CPPI5_INFO0_HDESC_TYPE_SHIFT		(30U)
+#define CPPI5_INFO0_HDESC_TYPE_MASK		GENMASK(31, 30)
+#define   CPPI5_INFO0_DESC_TYPE_VAL_HOST	(1U)
+#define   CPPI5_INFO0_DESC_TYPE_VAL_MONO	(2U)
+#define   CPPI5_INFO0_DESC_TYPE_VAL_TR		(3U)
+#define CPPI5_INFO0_HDESC_EPIB_PRESENT		BIT(29)
+/*
+ * Protocol Specific Words location:
+ * 0 - located in the descriptor,
+ * 1 = located in the SOP Buffer immediately prior to the data.
+ */
+#define CPPI5_INFO0_HDESC_PSINFO_LOCATION	BIT(28)
+#define CPPI5_INFO0_HDESC_PSINFO_SIZE_SHIFT	(22U)
+#define CPPI5_INFO0_HDESC_PSINFO_SIZE_MASK	GENMASK(27, 22)
+#define CPPI5_INFO0_HDESC_PKTLEN_SHIFT		(0)
+#define CPPI5_INFO0_HDESC_PKTLEN_MASK		GENMASK(21, 0)
+
+#define CPPI5_INFO1_DESC_PKTERROR_SHIFT		(28U)
+#define CPPI5_INFO1_DESC_PKTERROR_MASK		GENMASK(31, 28)
+#define CPPI5_INFO1_HDESC_PSFLGS_SHIFT		(24U)
+#define CPPI5_INFO1_HDESC_PSFLGS_MASK		GENMASK(27, 24)
+#define CPPI5_INFO1_DESC_PKTID_SHIFT		(14U)
+#define CPPI5_INFO1_DESC_PKTID_MASK		GENMASK(23, 14)
+#define CPPI5_INFO1_DESC_FLOWID_SHIFT		(0)
+#define CPPI5_INFO1_DESC_FLOWID_MASK		GENMASK(13, 0)
+
+#define CPPI5_INFO2_HDESC_PKTTYPE_SHIFT		(27U)
+#define CPPI5_INFO2_HDESC_PKTTYPE_MASK		GENMASK(31, 27)
+/* Return Policy: 0 - Entire packet 1 - Each buffer */
+#define CPPI5_INFO2_HDESC_RETPOLICY		BIT(18)
+/*
+ * Early Return:
+ * 0 = desc pointers should be returned after all reads have been completed
+ * 1 = desc pointers should be returned immediately upon fetching
+ * the descriptor and beginning to transfer data.
+ */
+#define CPPI5_INFO2_HDESC_EARLYRET		BIT(17)
+/*
+ * Return Push Policy:
+ * 0 = Descriptor must be returned to tail of queue
+ * 1 = Descriptor must be returned to head of queue
+ */
+#define CPPI5_INFO2_DESC_RETPUSHPOLICY		BIT(16)
+#define CPPI5_INFO2_DESC_RETQ_SHIFT		(0)
+#define CPPI5_INFO2_DESC_RETQ_MASK		GENMASK(15, 0)
+
+#define CPPI5_INFO3_DESC_SRCTAG_SHIFT		(16U)
+#define CPPI5_INFO3_DESC_SRCTAG_MASK		GENMASK(31, 16)
+#define CPPI5_INFO3_DESC_DSTTAG_SHIFT		(0)
+#define CPPI5_INFO3_DESC_DSTTAG_MASK		GENMASK(15, 0)
+
+#define CPPI5_BUFINFO1_HDESC_DATA_LEN_SHIFT	(0)
+#define CPPI5_BUFINFO1_HDESC_DATA_LEN_MASK	GENMASK(27, 0)
+
+#define CPPI5_OBUFINFO0_HDESC_BUF_LEN_SHIFT	(0)
+#define CPPI5_OBUFINFO0_HDESC_BUF_LEN_MASK	GENMASK(27, 0)
+
+/*
+ * Host Packet Descriptor Extended Packet Info Block
+ */
+struct cppi5_desc_epib_t {
+	u32 timestamp;	/* w0: application specific timestamp */
+	u32 sw_info0;	/* w1: Software Info 0 */
+	u32 sw_info1;	/* w2: Software Info 1 */
+	u32 sw_info2;	/* w3: Software Info 2 */
+};
+
+/**
+ * Monolithic-mode packet descriptor
+ */
+struct cppi5_monolithic_desc_t {
+	struct cppi5_desc_hdr_t hdr;
+	u32 epib[0];	/* Extended Packet Info Data (optional, 4 words) */
+	/*
+	 * Protocol Specific Data (optional, 0-128 bytes in multiples of 4),
+	 *  and/or Other Software Data (0-N bytes, optional)
+	 */
+};
+
+#define CPPI5_INFO2_MDESC_DATA_OFFSET_SHIFT	(18U)
+#define CPPI5_INFO2_MDESC_DATA_OFFSET_MASK	GENMASK(26, 18)
+
+/*
+ * Reload Enable:
+ * 0 = Finish the packet and place the descriptor back on the return queue
+ * 1 = Vector to the Reload Index and resume processing
+ */
+#define CPPI5_INFO0_TRDESC_RLDCNT_SHIFT		(20U)
+#define CPPI5_INFO0_TRDESC_RLDCNT_MASK		GENMASK(28, 20)
+#define CPPI5_INFO0_TRDESC_RLDCNT_MAX		(0x1ff)
+#define CPPI5_INFO0_TRDESC_RLDCNT_INFINITE	CPPI5_INFO0_TRDESC_RLDCNT_MAX
+#define CPPI5_INFO0_TRDESC_RLDIDX_SHIFT		(14U)
+#define CPPI5_INFO0_TRDESC_RLDIDX_MASK		GENMASK(19, 14)
+#define CPPI5_INFO0_TRDESC_RLDIDX_MAX		(0x3f)
+#define CPPI5_INFO0_TRDESC_LASTIDX_SHIFT	(0)
+#define CPPI5_INFO0_TRDESC_LASTIDX_MASK		GENMASK(13, 0)
+
+#define CPPI5_INFO1_TRDESC_RECSIZE_SHIFT	(24U)
+#define CPPI5_INFO1_TRDESC_RECSIZE_MASK		GENMASK(26, 24)
+#define   CPPI5_INFO1_TRDESC_RECSIZE_VAL_16B	(0)
+#define   CPPI5_INFO1_TRDESC_RECSIZE_VAL_32B	(1U)
+#define   CPPI5_INFO1_TRDESC_RECSIZE_VAL_64B	(2U)
+#define   CPPI5_INFO1_TRDESC_RECSIZE_VAL_128B	(3U)
+
+static inline void cppi5_desc_dump(void *desc, u32 size)
+{
+	print_hex_dump(KERN_ERR "dump udmap_desc: ", DUMP_PREFIX_NONE,
+		       32, 4, desc, size, false);
+}
+
+/**
+ * cppi5_desc_get_type - get descriptor type
+ * @desc_hdr: packet descriptor/TR header
+ *
+ * Returns descriptor type:
+ * CPPI5_INFO0_DESC_TYPE_VAL_HOST
+ * CPPI5_INFO0_DESC_TYPE_VAL_MONO
+ * CPPI5_INFO0_DESC_TYPE_VAL_TR
+ */
+static inline u32 cppi5_desc_get_type(struct cppi5_desc_hdr_t *desc_hdr)
+{
+	WARN_ON(!desc_hdr);
+
+	return (desc_hdr->pkt_info0 & CPPI5_INFO0_HDESC_TYPE_MASK) >>
+		CPPI5_INFO0_HDESC_TYPE_SHIFT;
+}
+
+/**
+ * cppi5_desc_get_errflags - get Error Flags from Desc
+ * @desc_hdr: packet/TR descriptor header
+ *
+ * Returns Error Flags from Packet/TR Descriptor
+ */
+static inline u32 cppi5_desc_get_errflags(struct cppi5_desc_hdr_t *desc_hdr)
+{
+	WARN_ON(!desc_hdr);
+
+	return (desc_hdr->pkt_info1 & CPPI5_INFO1_DESC_PKTERROR_MASK) >>
+		CPPI5_INFO1_DESC_PKTERROR_SHIFT;
+}
+
+/**
+ * cppi5_desc_get_pktids - get Packet and Flow ids from Desc
+ * @desc_hdr: packet/TR descriptor header
+ * @pkt_id: Packet ID
+ * @flow_id: Flow ID
+ *
+ * Returns Packet and Flow ids from packet/TR descriptor
+ */
+static inline void cppi5_desc_get_pktids(struct cppi5_desc_hdr_t *desc_hdr,
+					 u32 *pkt_id, u32 *flow_id)
+{
+	WARN_ON(!desc_hdr);
+
+	*pkt_id = (desc_hdr->pkt_info1 & CPPI5_INFO1_DESC_PKTID_MASK) >>
+		   CPPI5_INFO1_DESC_PKTID_SHIFT;
+	*flow_id = (desc_hdr->pkt_info1 & CPPI5_INFO1_DESC_FLOWID_MASK) >>
+		    CPPI5_INFO1_DESC_FLOWID_SHIFT;
+}
+
+/**
+ * cppi5_desc_set_pktids - set Packet and Flow ids in Desc
+ * @desc_hdr: packet/TR descriptor header
+ * @pkt_id: Packet ID
+ * @flow_id: Flow ID
+ */
+static inline void cppi5_desc_set_pktids(struct cppi5_desc_hdr_t *desc_hdr,
+					 u32 pkt_id, u32 flow_id)
+{
+	WARN_ON(!desc_hdr);
+
+	desc_hdr->pkt_info1 |= (pkt_id << CPPI5_INFO1_DESC_PKTID_SHIFT) &
+				CPPI5_INFO1_DESC_PKTID_MASK;
+	desc_hdr->pkt_info1 |= (flow_id << CPPI5_INFO1_DESC_FLOWID_SHIFT) &
+				CPPI5_INFO1_DESC_FLOWID_MASK;
+}
+
+/**
+ * cppi5_desc_set_retpolicy - set Packet Return Policy in Desc
+ * @desc_hdr: packet/TR descriptor header
+ * @flags: fags, supported values
+ *  CPPI5_INFO2_HDESC_RETPOLICY
+ *  CPPI5_INFO2_HDESC_EARLYRET
+ *  CPPI5_INFO2_DESC_RETPUSHPOLICY
+ * @return_ring_id: Packet Return Queue/Ring id, value 0xFFFF reserved
+ */
+static inline void cppi5_desc_set_retpolicy(struct cppi5_desc_hdr_t *desc_hdr,
+					    u32 flags, u32 return_ring_id)
+{
+	WARN_ON(!desc_hdr);
+
+	desc_hdr->pkt_info2 |= flags;
+	desc_hdr->pkt_info2 |= return_ring_id & CPPI5_INFO2_DESC_RETQ_MASK;
+}
+
+/**
+ * cppi5_desc_get_tags_ids - get Packet Src/Dst Tags from Desc
+ * @desc_hdr: packet/TR descriptor header
+ * @src_tag_id: Source Tag
+ * @dst_tag_id: Dest Tag
+ *
+ * Returns Packet Src/Dst Tags from packet/TR descriptor
+ */
+static inline void cppi5_desc_get_tags_ids(struct cppi5_desc_hdr_t *desc_hdr,
+					   u32 *src_tag_id, u32 *dst_tag_id)
+{
+	WARN_ON(!desc_hdr);
+
+	if (src_tag_id)
+		*src_tag_id = (desc_hdr->src_dst_tag &
+			      CPPI5_INFO3_DESC_SRCTAG_MASK) >>
+			      CPPI5_INFO3_DESC_SRCTAG_SHIFT;
+	if (dst_tag_id)
+		*dst_tag_id = desc_hdr->src_dst_tag &
+			      CPPI5_INFO3_DESC_DSTTAG_MASK;
+}
+
+/**
+ * cppi5_desc_set_tags_ids - set Packet Src/Dst Tags in HDesc
+ * @desc_hdr: packet/TR descriptor header
+ * @src_tag_id: Source Tag
+ * @dst_tag_id: Dest Tag
+ *
+ * Returns Packet Src/Dst Tags from packet/TR descriptor
+ */
+static inline void cppi5_desc_set_tags_ids(struct cppi5_desc_hdr_t *desc_hdr,
+					   u32 src_tag_id, u32 dst_tag_id)
+{
+	WARN_ON(!desc_hdr);
+
+	desc_hdr->src_dst_tag = (src_tag_id << CPPI5_INFO3_DESC_SRCTAG_SHIFT) &
+				CPPI5_INFO3_DESC_SRCTAG_MASK;
+	desc_hdr->src_dst_tag |= dst_tag_id & CPPI5_INFO3_DESC_DSTTAG_MASK;
+}
+
+/**
+ * cppi5_hdesc_calc_size - Calculate Host Packet Descriptor size
+ * @epib: is EPIB present
+ * @psdata_size: PSDATA size
+ * @sw_data_size: SWDATA size
+ *
+ * Returns required Host Packet Descriptor size
+ * 0 - if PSDATA > CPPI5_INFO0_HDESC_PSDATA_MAX_SIZE
+ */
+static inline u32 cppi5_hdesc_calc_size(bool epib, u32 psdata_size,
+					u32 sw_data_size)
+{
+	u32 desc_size;
+
+	if (psdata_size > CPPI5_INFO0_HDESC_PSDATA_MAX_SIZE)
+		return 0;
+	//TODO_GS: align
+	desc_size = sizeof(struct cppi5_host_desc_t) + psdata_size +
+		    sw_data_size;
+
+	if (epib)
+		desc_size += CPPI5_INFO0_HDESC_EPIB_SIZE;
+
+	return ALIGN(desc_size, CPPI5_DESC_MIN_ALIGN);
+}
+
+/**
+ * cppi5_hdesc_init - Init Host Packet Descriptor size
+ * @desc: Host packet descriptor
+ * @flags: supported values
+ *	CPPI5_INFO0_HDESC_EPIB_PRESENT
+ *	CPPI5_INFO0_HDESC_PSINFO_LOCATION
+ * @psdata_size: PSDATA size
+ *
+ * Returns required Host Packet Descriptor size
+ * 0 - if PSDATA > CPPI5_INFO0_HDESC_PSDATA_MAX_SIZE
+ */
+static inline void cppi5_hdesc_init(struct cppi5_host_desc_t *desc, u32 flags,
+				    u32 psdata_size)
+{
+	WARN_ON(!desc);
+	WARN_ON(psdata_size > CPPI5_INFO0_HDESC_PSDATA_MAX_SIZE);
+	WARN_ON(flags & ~(CPPI5_INFO0_HDESC_EPIB_PRESENT |
+			  CPPI5_INFO0_HDESC_PSINFO_LOCATION));
+
+	desc->hdr.pkt_info0 = (CPPI5_INFO0_DESC_TYPE_VAL_HOST <<
+			       CPPI5_INFO0_HDESC_TYPE_SHIFT) | (flags);
+	desc->hdr.pkt_info0 |= ((psdata_size >> 2) <<
+				CPPI5_INFO0_HDESC_PSINFO_SIZE_SHIFT) &
+				CPPI5_INFO0_HDESC_PSINFO_SIZE_MASK;
+	desc->next_desc = 0;
+}
+
+/**
+ * cppi5_hdesc_update_flags - Replace descriptor flags
+ * @desc: Host packet descriptor
+ * @flags: supported values
+ *	CPPI5_INFO0_HDESC_EPIB_PRESENT
+ *	CPPI5_INFO0_HDESC_PSINFO_LOCATION
+ */
+static inline void cppi5_hdesc_update_flags(struct cppi5_host_desc_t *desc,
+					    u32 flags)
+{
+	WARN_ON(!desc);
+	WARN_ON(flags & ~(CPPI5_INFO0_HDESC_EPIB_PRESENT |
+			  CPPI5_INFO0_HDESC_PSINFO_LOCATION));
+
+	desc->hdr.pkt_info0 &= ~(CPPI5_INFO0_HDESC_EPIB_PRESENT |
+				 CPPI5_INFO0_HDESC_PSINFO_LOCATION);
+	desc->hdr.pkt_info0 |= flags;
+}
+
+/**
+ * cppi5_hdesc_update_psdata_size - Replace PSdata size
+ * @desc: Host packet descriptor
+ * @psdata_size: PSDATA size
+ */
+static inline void cppi5_hdesc_update_psdata_size(
+				struct cppi5_host_desc_t *desc, u32 psdata_size)
+{
+	WARN_ON(!desc);
+	WARN_ON(psdata_size > CPPI5_INFO0_HDESC_PSDATA_MAX_SIZE);
+
+	desc->hdr.pkt_info0 &= ~CPPI5_INFO0_HDESC_PSINFO_SIZE_MASK;
+	desc->hdr.pkt_info0 |= ((psdata_size >> 2) <<
+				CPPI5_INFO0_HDESC_PSINFO_SIZE_SHIFT) &
+				CPPI5_INFO0_HDESC_PSINFO_SIZE_MASK;
+}
+
+/**
+ * cppi5_hdesc_get_psdata_size - get PSdata size in bytes
+ * @desc: Host packet descriptor
+ */
+static inline u32 cppi5_hdesc_get_psdata_size(struct cppi5_host_desc_t *desc)
+{
+	u32 psdata_size = 0;
+
+	WARN_ON(!desc);
+
+	if (!(desc->hdr.pkt_info0 & CPPI5_INFO0_HDESC_PSINFO_LOCATION))
+		psdata_size = (desc->hdr.pkt_info0 &
+			       CPPI5_INFO0_HDESC_PSINFO_SIZE_MASK) >>
+			       CPPI5_INFO0_HDESC_PSINFO_SIZE_SHIFT;
+
+	return (psdata_size << 2);
+}
+
+/**
+ * cppi5_hdesc_get_pktlen - get Packet Length from HDesc
+ * @desc: Host packet descriptor
+ *
+ * Returns Packet Length from Host Packet Descriptor
+ */
+static inline u32 cppi5_hdesc_get_pktlen(struct cppi5_host_desc_t *desc)
+{
+	WARN_ON(!desc);
+
+	return (desc->hdr.pkt_info0 & CPPI5_INFO0_HDESC_PKTLEN_MASK);
+}
+
+/**
+ * cppi5_hdesc_set_pktlen - set Packet Length in HDesc
+ * @desc: Host packet descriptor
+ */
+static inline void cppi5_hdesc_set_pktlen(struct cppi5_host_desc_t *desc,
+					  u32 pkt_len)
+{
+	WARN_ON(!desc);
+
+	desc->hdr.pkt_info0 |= (pkt_len & CPPI5_INFO0_HDESC_PKTLEN_MASK);
+}
+
+/**
+ * cppi5_hdesc_get_psflags - get Protocol Specific Flags from HDesc
+ * @desc: Host packet descriptor
+ *
+ * Returns Protocol Specific Flags from Host Packet Descriptor
+ */
+static inline u32 cppi5_hdesc_get_psflags(struct cppi5_host_desc_t *desc)
+{
+	WARN_ON(!desc);
+
+	return (desc->hdr.pkt_info1 & CPPI5_INFO1_HDESC_PSFLGS_MASK) >>
+		CPPI5_INFO1_HDESC_PSFLGS_SHIFT;
+}
+
+/**
+ * cppi5_hdesc_set_psflags - set Protocol Specific Flags in HDesc
+ * @desc: Host packet descriptor
+ */
+static inline void cppi5_hdesc_set_psflags(struct cppi5_host_desc_t *desc,
+					   u32 ps_flags)
+{
+	WARN_ON(!desc);
+
+	desc->hdr.pkt_info1 |= (ps_flags <<
+				CPPI5_INFO1_HDESC_PSFLGS_SHIFT) &
+				CPPI5_INFO1_HDESC_PSFLGS_MASK;
+}
+
+/**
+ * cppi5_hdesc_get_errflags - get Packet Type from HDesc
+ * @desc: Host packet descriptor
+ */
+static inline u32 cppi5_hdesc_get_pkttype(struct cppi5_host_desc_t *desc)
+{
+	WARN_ON(!desc);
+
+	return (desc->hdr.pkt_info2 & CPPI5_INFO2_HDESC_PKTTYPE_MASK) >>
+		CPPI5_INFO2_HDESC_PKTTYPE_SHIFT;
+}
+
+/**
+ * cppi5_hdesc_get_errflags - set Packet Type in HDesc
+ * @desc: Host packet descriptor
+ * @pkt_type: Packet Type
+ */
+static inline void cppi5_hdesc_set_pkttype(struct cppi5_host_desc_t *desc,
+					   u32 pkt_type)
+{
+	WARN_ON(!desc);
+	desc->hdr.pkt_info2 |=
+			(pkt_type << CPPI5_INFO2_HDESC_PKTTYPE_SHIFT) &
+			 CPPI5_INFO2_HDESC_PKTTYPE_MASK;
+}
+
+/**
+ * cppi5_hdesc_attach_buf - attach buffer to HDesc
+ * @desc: Host packet descriptor
+ * @buf: Buffer physical address
+ * @buf_data_len: Buffer length
+ * @obuf: Original Buffer physical address
+ * @obuf_len: Original Buffer length
+ *
+ * Attaches buffer to Host Packet Descriptor
+ */
+static inline void cppi5_hdesc_attach_buf(struct cppi5_host_desc_t *desc,
+					  dma_addr_t buf, u32 buf_data_len,
+					  dma_addr_t obuf, u32 obuf_len)
+{
+	WARN_ON(!desc);
+	WARN_ON(!buf && !obuf);
+
+	desc->buf_ptr = buf;
+	desc->buf_info1 = buf_data_len & CPPI5_BUFINFO1_HDESC_DATA_LEN_MASK;
+	desc->org_buf_ptr = obuf;
+	desc->org_buf_len = obuf_len & CPPI5_OBUFINFO0_HDESC_BUF_LEN_MASK;
+}
+
+static inline void cppi5_hdesc_get_obuf(struct cppi5_host_desc_t *desc,
+					dma_addr_t *obuf, u32 *obuf_len)
+{
+	WARN_ON(!desc);
+	WARN_ON(!obuf);
+	WARN_ON(!obuf_len);
+
+	*obuf = desc->org_buf_ptr;
+	*obuf_len = desc->org_buf_len & CPPI5_OBUFINFO0_HDESC_BUF_LEN_MASK;
+}
+
+static inline void cppi5_hdesc_reset_to_original(struct cppi5_host_desc_t *desc)
+{
+	WARN_ON(!desc);
+
+	desc->buf_ptr = desc->org_buf_ptr;
+	desc->buf_info1 = desc->org_buf_len;
+}
+
+/**
+ * cppi5_hdesc_link_hbdesc - link Host Buffer Descriptor to HDesc
+ * @desc: Host Packet Descriptor
+ * @buf_desc: Host Buffer Descriptor physical address
+ *
+ * add and link Host Buffer Descriptor to HDesc
+ */
+static inline void cppi5_hdesc_link_hbdesc(struct cppi5_host_desc_t *desc,
+					   dma_addr_t hbuf_desc)
+{
+	WARN_ON(!desc);
+	WARN_ON(!hbuf_desc);
+
+	desc->next_desc = hbuf_desc;
+}
+
+static inline dma_addr_t cppi5_hdesc_get_next_hbdesc(
+				struct cppi5_host_desc_t *desc)
+{
+	WARN_ON(!desc);
+
+	return (dma_addr_t)desc->next_desc;
+}
+
+static inline void cppi5_hdesc_reset_hbdesc(struct cppi5_host_desc_t *desc)
+{
+	WARN_ON(!desc);
+
+	desc->hdr = (struct cppi5_desc_hdr_t) { 0 };
+	desc->next_desc = 0;
+}
+
+/**
+ * cppi5_hdesc_epib_present -  check if EPIB present
+ * @desc_hdr: packet descriptor/TR header
+ *
+ * Returns true if EPIB present in the packet
+ */
+static inline bool cppi5_hdesc_epib_present(struct cppi5_desc_hdr_t *desc_hdr)
+{
+	WARN_ON(!desc_hdr);
+	return !!(desc_hdr->pkt_info0 & CPPI5_INFO0_HDESC_EPIB_PRESENT);
+}
+
+/**
+ * cppi5_hdesc_get_psdata -  Get pointer on PSDATA
+ * @desc: Host packet descriptor
+ *
+ * Returns pointer on PSDATA in HDesc.
+ * NULL - if ps_data placed at the start of data buffer.
+ */
+static inline void *cppi5_hdesc_get_psdata(struct cppi5_host_desc_t *desc)
+{
+	u32 psdata_size;
+	void *psdata;
+
+	WARN_ON(!desc);
+
+	if (desc->hdr.pkt_info0 & CPPI5_INFO0_HDESC_PSINFO_LOCATION)
+		return NULL;
+
+	psdata_size = (desc->hdr.pkt_info0 &
+		       CPPI5_INFO0_HDESC_PSINFO_SIZE_MASK) >>
+		       CPPI5_INFO0_HDESC_PSINFO_SIZE_SHIFT;
+
+	if (!psdata_size)
+		return NULL;
+
+	psdata = &desc->epib;
+
+	if (cppi5_hdesc_epib_present(&desc->hdr))
+		psdata += CPPI5_INFO0_HDESC_EPIB_SIZE;
+
+	return psdata;
+}
+
+static inline u32 *cppi5_hdesc_get_psdata32(struct cppi5_host_desc_t *desc)
+{
+	return (u32 *)cppi5_hdesc_get_psdata(desc);
+}
+
+/**
+ * cppi5_hdesc_get_swdata -  Get pointer on swdata
+ * @desc: Host packet descriptor
+ *
+ * Returns pointer on SWDATA in HDesc.
+ * NOTE. It's caller responsibility to be sure hdesc actually has swdata.
+ */
+static inline void *cppi5_hdesc_get_swdata(struct cppi5_host_desc_t *desc)
+{
+	u32 psdata_size = 0;
+	void *swdata;
+
+	WARN_ON(!desc);
+
+	if (!(desc->hdr.pkt_info0 & CPPI5_INFO0_HDESC_PSINFO_LOCATION))
+		psdata_size = (desc->hdr.pkt_info0 &
+			       CPPI5_INFO0_HDESC_PSINFO_SIZE_MASK) >>
+			       CPPI5_INFO0_HDESC_PSINFO_SIZE_SHIFT;
+
+	swdata = &desc->epib;
+
+	if (cppi5_hdesc_epib_present(&desc->hdr))
+		swdata += CPPI5_INFO0_HDESC_EPIB_SIZE;
+
+	swdata += (psdata_size << 2);
+
+	return swdata;
+}
+
+/* ================================== TR ================================== */
+
+#define CPPI5_TR_TYPE_SHIFT			(0U)
+#define CPPI5_TR_TYPE_MASK			GENMASK(3, 0)
+#define CPPI5_TR_STATIC				BIT(4)
+#define CPPI5_TR_WAIT				BIT(5)
+#define CPPI5_TR_EVENT_SIZE_SHIFT		(6U)
+#define CPPI5_TR_EVENT_SIZE_MASK		GENMASK(7, 6)
+#define CPPI5_TR_TRIGGER0_SHIFT			(8U)
+#define CPPI5_TR_TRIGGER0_MASK			GENMASK(9, 8)
+#define CPPI5_TR_TRIGGER0_TYPE_SHIFT		(10U)
+#define CPPI5_TR_TRIGGER0_TYPE_MASK		GENMASK(11, 10)
+#define CPPI5_TR_TRIGGER1_SHIFT			(12U)
+#define CPPI5_TR_TRIGGER1_MASK			GENMASK(13, 12)
+#define CPPI5_TR_TRIGGER1_TYPE_SHIFT		(14U)
+#define CPPI5_TR_TRIGGER1_TYPE_MASK		GENMASK(15, 14)
+#define CPPI5_TR_CMD_ID_SHIFT			(16U)
+#define CPPI5_TR_CMD_ID_MASK			GENMASK(23, 16)
+#define CPPI5_TR_CSF_FLAGS_SHIFT		(24U)
+#define CPPI5_TR_CSF_FLAGS_MASK			GENMASK(31, 24)
+#define   CPPI5_TR_CSF_SA_INDIRECT		BIT(0)
+#define   CPPI5_TR_CSF_DA_INDIRECT		BIT(1)
+#define   CPPI5_TR_CSF_SUPR_EVT			BIT(2)
+#define   CPPI5_TR_CSF_EOL_ADV_SHIFT		(4U)
+#define   CPPI5_TR_CSF_EOL_ADV_MASK		GENMASK(6, 4)
+#define   CPPI5_TR_CSF_EOP			BIT(7)
+
+/* Udmap TR flags Type field specifies the type of TR. */
+enum cppi5_tr_types {
+	/* type0: One dimensional data move */
+	CPPI5_TR_TYPE0 = 0,
+	/* type1: Two dimensional data move */
+	CPPI5_TR_TYPE1,
+	/* type2: Three dimensional data move */
+	CPPI5_TR_TYPE2,
+	/* type3: Four dimensional data move */
+	CPPI5_TR_TYPE3,
+	/* type4: Four dimensional data move with data formatting */
+	CPPI5_TR_TYPE4,
+	/* type5: Four dimensional Cache Warm */
+	CPPI5_TR_TYPE5,
+	/* type6-7: Reserved */
+	/* type8: Four Dimensional Block Move */
+	CPPI5_TR_TYPE8 = 8,
+	/* type9: Four Dimensional Block Move with Repacking */
+	CPPI5_TR_TYPE9,
+	/* type10: Two Dimensional Block Move */
+	CPPI5_TR_TYPE10,
+	/* type11: Two Dimensional Block Move with Repacking */
+	CPPI5_TR_TYPE11,
+	/* type12-14: Reserved */
+	/* type15 Four Dimensional Block Move with Repacking and Indirection */
+	CPPI5_TR_TYPE15 = 15,
+	CPPI5_TR_TYPE_MAX
+};
+
+/*
+ * Udmap TR Flags EVENT_SIZE field specifies when an event is generated
+ * for each TR.
+ */
+enum cppi5_tr_event_size {
+	/* When TR is complete and all status for the TR has been received */
+	CPPI5_TR_EVENT_SIZE_COMPLETION,
+	/*
+	 * Type 0: when the last data transaction is sent for the TR;
+	 * Type 1-11: when ICNT1 is decremented
+	 */
+	CPPI5_TR_EVENT_SIZE_ICNT1_DEC,
+	/*
+	 * Type 0-1,10-11: when the last data transaction is sent for the TR;
+	 * All other types: when ICNT2 is decremented
+	 */
+	CPPI5_TR_EVENT_SIZE_ICNT2_DEC,
+	/*
+	 * Type 0-2,10-11: when the last data transaction is sent for the TR;
+	 * All other types: when ICNT3 is decremented
+	 */
+	CPPI5_TR_EVENT_SIZE_ICNT3_DEC,
+	CPPI5_TR_EVENT_SIZE_MAX
+};
+
+/*
+ * Udmap TR Flags TRIGGERx field specifies the type of trigger used to
+ * enable the TR to transfer data as specified by TRIGGERx_TYPE field.
+ */
+enum cppi5_tr_trigger {
+	CPPI5_TR_TRIGGER_NONE,		/* No Trigger */
+	CPPI5_TR_TRIGGER_GLOBAL0,		/* Global Trigger 0 */
+	CPPI5_TR_TRIGGER_GLOBAL1,		/* Global Trigger 1 */
+	CPPI5_TR_TRIGGER_LOCAL_EVENT,	/* Local Event */
+	CPPI5_TR_TRIGGER_MAX
+};
+
+/*
+ * Udmap TR Flags TRIGGERx_TYPE field specifies the type of data transfer
+ * that will be enabled by receiving a trigger as specified by TRIGGERx.
+ */
+enum cppi5_tr_trigger_type {
+	/* The second inner most loop (ICNT1) will be decremented by 1 */
+	CPPI5_TR_TRIGGER_TYPE_ICNT1_DEC,
+	/* The third inner most loop (ICNT2) will be decremented by 1 */
+	CPPI5_TR_TRIGGER_TYPE_ICNT2_DEC,
+	/* The outer most loop (ICNT3) will be decremented by 1 */
+	CPPI5_TR_TRIGGER_TYPE_ICNT3_DEC,
+	/* The entire TR will be allowed to complete */
+	CPPI5_TR_TRIGGER_TYPE_ALL,
+	CPPI5_TR_TRIGGER_TYPE_MAX
+};
+
+typedef u32 cppi5_tr_flags_t;
+
+/* Type 0 (One dimensional data move) TR (16 byte) */
+struct cppi5_tr_type0_t {
+	cppi5_tr_flags_t flags;
+	u16 icnt0;
+	u16 unused;
+	u64 addr;
+} __aligned(16) __packed;
+
+/* Type 1 (Two dimensional data move) TR (32 byte) */
+struct cppi5_tr_type1_t {
+	cppi5_tr_flags_t flags;
+	u16 icnt0;
+	u16 icnt1;
+	u64 addr;
+	s32 dim1;
+} __aligned(32) __packed;
+
+/* Type 2 (Three dimensional data move) TR (32 byte) */
+struct cppi5_tr_type2_t {
+	cppi5_tr_flags_t flags;
+	u16 icnt0;
+	u16 icnt1;
+	u64 addr;
+	s32 dim1;
+	u16 icnt2;
+	u16 unused;
+	s32 dim2;
+} __aligned(32) __packed;
+
+/* Type 3 (Four dimensional data move) TR (32 byte) */
+struct cppi5_tr_type3_t {
+	cppi5_tr_flags_t flags;
+	u16 icnt0;
+	u16 icnt1;
+	u64 addr;
+	s32 dim1;
+	u16 icnt2;
+	u16 icnt3;
+	s32 dim2;
+	s32 dim3;
+} __aligned(32) __packed;
+
+/*
+ * Type 15 (Four Dimensional Block Copy with Repacking and
+ * Indirection Support) TR (64 byte).
+ */
+struct cppi5_tr_type15_t {
+	cppi5_tr_flags_t flags;
+	u16 icnt0;
+	u16 icnt1;
+	u64 addr;
+	s32 dim1;
+	u16 icnt2;
+	u16 icnt3;
+	s32 dim2;
+	s32 dim3;
+	u32 _reserved;
+	s32 ddim1;
+	u64 daddr;
+	s32 ddim2;
+	s32 ddim3;
+	u16 dicnt0;
+	u16 dicnt1;
+	u16 dicnt2;
+	u16 dicnt3;
+} __aligned(64) __packed;
+
+struct cppi5_tr_resp_t {
+	u8 status;
+	u8 reserved;
+	u8 cmd_id;
+	u8 flags;
+} __packed;
+
+#define CPPI5_TR_RESPONSE_STATUS_TYPE_SHIFT	(0U)
+#define CPPI5_TR_RESPONSE_STATUS_TYPE_MASK	GENMASK(3, 0)
+#define CPPI5_TR_RESPONSE_STATUS_INFO_SHIFT	(4U)
+#define CPPI5_TR_RESPONSE_STATUS_INFO_MASK	GENMASK(7, 4)
+#define CPPI5_TR_RESPONSE_CMDID_SHIFT		(16U)
+#define CPPI5_TR_RESPONSE_CMDID_MASK		GENMASK(23, 16)
+#define CPPI5_TR_RESPONSE_CFG_SPECIFIC_SHIFT	(24U)
+#define CPPI5_TR_RESPONSE_CFG_SPECIFIC_MASK	GENMASK(31, 24)
+
+/*
+ * Udmap TR Response Status Type field is used to determine
+ * what type of status is being returned.
+ */
+enum cppi5_tr_resp_status_type {
+	CPPI5_TR_RESPONSE_STATUS_COMPLETE,		/* None */
+	CPPI5_TR_RESPONSE_STATUS_TRANSFER_ERR,		/* Transfer Error */
+	CPPI5_TR_RESPONSE_STATUS_ABORTED_ERR,		/* Aborted Error */
+	CPPI5_TR_RESPONSE_STATUS_SUBMISSION_ERR,	/* Submission Error */
+	CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_ERR,	/* Unsup. Feature */
+	CPPI5_TR_RESPONSE_STATUS_MAX
+};
+
+/*
+ * Udmap TR Response Status field values which corresponds
+ * CPPI5_TR_RESPONSE_STATUS_SUBMISSION_ERR
+ */
+enum cppi5_tr_resp_status_submission {
+	/* ICNT0 was 0 */
+	CPPI5_TR_RESPONSE_STATUS_SUBMISSION_ICNT0,
+	/* Channel FIFO was full when TR received */
+	CPPI5_TR_RESPONSE_STATUS_SUBMISSION_FIFO_FULL,
+	/* Channel is not owned by the submitter */
+	CPPI5_TR_RESPONSE_STATUS_SUBMISSION_OWN,
+	CPPI5_TR_RESPONSE_STATUS_SUBMISSION_MAX
+};
+
+/*
+ * Udmap TR Response Status field values which corresponds
+ * CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_ERR
+ */
+enum cppi5_tr_resp_status_unsupported {
+	/* TR Type not supported */
+	CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_TR_TYPE,
+	/* STATIC not supported */
+	CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_STATIC,
+	/* EOL not supported */
+	CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_EOL,
+	/* CONFIGURATION SPECIFIC not supported */
+	CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_CFG_SPECIFIC,
+	/* AMODE not supported */
+	CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_AMODE,
+	/* ELTYPE not supported */
+	CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_ELTYPE,
+	/* DFMT not supported */
+	CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_DFMT,
+	/* SECTR not supported */
+	CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_SECTR,
+	/* AMODE SPECIFIC field not supported */
+	CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_AMODE_SPECIFIC,
+	CPPI5_TR_RESPONSE_STATUS_UNSUPPORTED_MAX
+};
+
+/**
+ * cppi5_trdesc_calc_size - Calculate TR Descriptor size
+ * @tr_count: number of TR records
+ * @tr_size: Nominal size of TR record (max) [16, 32, 64, 128]
+ *
+ * Returns required TR Descriptor size
+ */
+static inline size_t cppi5_trdesc_calc_size(u32 tr_count, u32 tr_size)
+{
+	/*
+	 * The Size of a TR descriptor is:
+	 * 1 x tr_size : the first 16 bytes is used by the packet info block +
+	 * tr_count x tr_size : Transfer Request Records +
+	 * tr_count x sizeof(struct cppi5_tr_resp_t) : Transfer Response Records
+	 */
+	return tr_size * (tr_count + 1) +
+		sizeof(struct cppi5_tr_resp_t) * tr_count;
+}
+
+/**
+ * cppi5_trdesc_init - Init TR Descriptor
+ * @desc: TR Descriptor
+ * @tr_count: number of TR records
+ * @tr_size: Nominal size of TR record (max) [16, 32, 64, 128]
+ * @reload_idx: Absolute index to jump to on the 2nd and following passes
+ *		through the TR packet.
+ * @reload_count: Number of times to jump from last entry to reload_idx. 0x1ff
+ *		  indicates infinite looping.
+ *
+ * Init TR Descriptor
+ */
+static inline void cppi5_trdesc_init(struct cppi5_desc_hdr_t *desc_hdr,
+				     u32 tr_count, u32 tr_size, u32 reload_idx,
+				     u32 reload_count)
+{
+	WARN_ON(!desc_hdr);
+	WARN_ON(tr_count & ~CPPI5_INFO0_TRDESC_LASTIDX_MASK);
+	WARN_ON(reload_idx > CPPI5_INFO0_TRDESC_RLDIDX_MAX);
+	WARN_ON(reload_count > CPPI5_INFO0_TRDESC_RLDCNT_MAX);
+
+	desc_hdr->pkt_info0 = CPPI5_INFO0_DESC_TYPE_VAL_TR <<
+			      CPPI5_INFO0_HDESC_TYPE_SHIFT;
+	desc_hdr->pkt_info0 |= (reload_count << CPPI5_INFO0_TRDESC_RLDCNT_SHIFT) &
+			       CPPI5_INFO0_TRDESC_RLDCNT_MASK;
+	desc_hdr->pkt_info0 |= (reload_idx << CPPI5_INFO0_TRDESC_RLDIDX_SHIFT) &
+			       CPPI5_INFO0_TRDESC_RLDIDX_MASK;
+	desc_hdr->pkt_info0 |= (tr_count - 1) & CPPI5_INFO0_TRDESC_LASTIDX_MASK;
+
+	desc_hdr->pkt_info1 |= ((ffs(tr_size >> 4) - 1) <<
+				CPPI5_INFO1_TRDESC_RECSIZE_SHIFT) &
+				CPPI5_INFO1_TRDESC_RECSIZE_MASK;
+}
+
+/**
+ * cppi5_tr_init - Init TR record
+ * @flags: Pointer to the TR's flags
+ * @type: TR type
+ * @static_tr: TR is static
+ * @wait: Wait for TR completion before allow the next TR to start
+ * @event_size: output event generation cfg
+ * @cmd_id: TR identifier (application specifics)
+ *
+ * Init TR record
+ */
+static inline void cppi5_tr_init(cppi5_tr_flags_t *flags,
+				 enum cppi5_tr_types type, bool static_tr,
+				 bool wait, enum cppi5_tr_event_size event_size,
+				 u32 cmd_id)
+{
+	WARN_ON(!flags);
+
+	*flags = type;
+	*flags |= (event_size << CPPI5_TR_EVENT_SIZE_SHIFT) &
+		  CPPI5_TR_EVENT_SIZE_MASK;
+
+	*flags |= (cmd_id << CPPI5_TR_CMD_ID_SHIFT) &
+		  CPPI5_TR_CMD_ID_MASK;
+
+	if (static_tr && (type == CPPI5_TR_TYPE8 || type == CPPI5_TR_TYPE9))
+		*flags |= CPPI5_TR_STATIC;
+
+	if (wait)
+		*flags |= CPPI5_TR_WAIT;
+}
+
+/**
+ * cppi5_tr_set_trigger - Configure trigger0/1 and trigger0/1_type
+ * @flags: Pointer to the TR's flags
+ * @trigger0: trigger0 selection
+ * @trigger0_type: type of data transfer that will be enabled by trigger0
+ * @trigger1: trigger1 selection
+ * @trigger1_type: type of data transfer that will be enabled by trigger1
+ *
+ * Configure the triggers for the TR
+ */
+static inline void cppi5_tr_set_trigger(cppi5_tr_flags_t *flags,
+				enum cppi5_tr_trigger trigger0,
+				enum cppi5_tr_trigger_type trigger0_type,
+				enum cppi5_tr_trigger trigger1,
+				enum cppi5_tr_trigger_type trigger1_type)
+{
+	WARN_ON(!flags);
+
+	*flags |= (trigger0 << CPPI5_TR_TRIGGER0_SHIFT) &
+		  CPPI5_TR_TRIGGER0_MASK;
+	*flags |= (trigger0_type << CPPI5_TR_TRIGGER0_TYPE_SHIFT) &
+		  CPPI5_TR_TRIGGER0_TYPE_MASK;
+
+	*flags |= (trigger1 << CPPI5_TR_TRIGGER1_SHIFT) &
+		  CPPI5_TR_TRIGGER1_MASK;
+	*flags |= (trigger1_type << CPPI5_TR_TRIGGER1_TYPE_SHIFT) &
+		  CPPI5_TR_TRIGGER1_TYPE_MASK;
+}
+
+/**
+ * cppi5_tr_cflag_set - Update the Configuration specific flags
+ * @flags: Pointer to the TR's flags
+ * @csf: Configuration specific flags
+ *
+ * Set a bit in Configuration Specific Flags section of the TR flags.
+ */
+static inline void cppi5_tr_csf_set(cppi5_tr_flags_t *flags, u32 csf)
+{
+	WARN_ON(!flags);
+
+	*flags |= (csf << CPPI5_TR_CSF_FLAGS_SHIFT) &
+		  CPPI5_TR_CSF_FLAGS_MASK;
+}
+
+#endif /* __TI_CPPI5_H__ */
Signature · 1 line
2.20.1
#5 lore raw

PATCH v3 3/7 soc: ti: k3: add CPPI5 description and helpers

Quoted 7 lines · Vignesh R

From: Grygorii Strashko <[email protected]>

Add TI Communications Port Programming Interface (CPPI) 5 interface description and helpers

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190201/7438bf5f/attachment.sig>
author maintainer
#6 lore raw

PATCH v3 4/7 dma: ti: add driver to K3 UDMA

In reply to Vignesh R

The UDMA-P is intended to perform similar (but significantly upgraded) functions as the packet-oriented DMA used on previous SoC devices. The UDMA-P module supports the transmission and reception of various packet types. The UDMA-P also supports acting as both a UTC and UDMA-C for its internal channels. Channels in the UDMA-P can be configured to be either Packet-Based or Third-Party channels on a channel by channel basis.

The initial driver supports:
- MEM_TO_MEM (TR mode)
- DEV_TO_MEM (Packet mode)
- MEM_TO_DEV (Packet mode)

---
 drivers/dma/Kconfig               |    2 +
 drivers/dma/Makefile              |    2 +
 drivers/dma/ti/Kconfig            |   14 +
 drivers/dma/ti/Makefile           |    3 +
 drivers/dma/ti/k3-udma-hwdef.h    |  184 +++
 drivers/dma/ti/k3-udma.c          | 1737 +++++++++++++++++++++++++++++
 include/dt-bindings/dma/k3-udma.h |   31 +
 include/linux/soc/ti/ti-udma.h    |   24 +
 8 files changed, 1997 insertions(+)
 create mode 100644 drivers/dma/ti/Kconfig
 create mode 100644 drivers/dma/ti/Makefile
 create mode 100644 drivers/dma/ti/k3-udma-hwdef.h
 create mode 100644 drivers/dma/ti/k3-udma.c
 create mode 100644 include/dt-bindings/dma/k3-udma.h
 create mode 100644 include/linux/soc/ti/ti-udma.h
drivers/dma/Kconfig +2 -0
index 1820676d7a18..4f37ba7d35eb 100644
@@ -57,4 +57,6 @@ config APBH_DMA_BURST8
 
 endif
 
+source "drivers/dma/ti/Kconfig"
+
 endmenu # menu "DMA Support"
drivers/dma/Makefile +2 -0
index b5f9147e0a54..afab324461b9 100644
@@ -13,3 +13,5 @@ obj-$(CONFIG_SANDBOX_DMA) += sandbox-dma-test.o
 obj-$(CONFIG_TI_KSNAV) += keystone_nav.o keystone_nav_cfg.o
 obj-$(CONFIG_TI_EDMA3) += ti-edma3.o
 obj-$(CONFIG_DMA_LPC32XX) += lpc32xx_dma.o
+
+obj-y += ti/
drivers/dma/ti/Kconfig new file +14 -0
new file mode 100644
index 000000000000..3d5498326c42
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+if ARCH_K3
+
+config TI_K3_NAVSS_UDMA
+        bool "Texas Instruments UDMA"
+        depends on ARCH_K3
+        select DMA
+        select TI_K3_NAVSS_RINGACC
+        select TI_K3_NAVSS_PSILCFG
+        default n
+        help
+          Support for UDMA used in K3 devices.
+endif
drivers/dma/ti/Makefile new file +3 -0
new file mode 100644
index 000000000000..de2f9ac91a46
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-$(CONFIG_TI_K3_NAVSS_UDMA) += k3-udma.o
drivers/dma/ti/k3-udma-hwdef.h new file +184 -0

184 lines not on this page · raw message

drivers/dma/ti/k3-udma.c new file +1737 -0

1,737 lines not on this page · raw message

include/dt-bindings/dma/k3-udma.h new file +31 -0
new file mode 100644
index 000000000000..670e1232b485
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ *  Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com
+ */
+
+#ifndef __DT_TI_UDMA_H
+#define __DT_TI_UDMA_H
+
+#define UDMA_TR_MODE		0
+#define UDMA_PKT_MODE		1
+
+#define UDMA_DIR_TX		0
+#define UDMA_DIR_RX		1
+
+#define PSIL_STATIC_TR_NONE	0
+#define PSIL_STATIC_TR_XY	1
+#define PSIL_STATIC_TR_MCAN	2
+
+#define UDMA_PDMA_TR_XY(id)				\
+	ti,psil-config##id {				\
+		linux,udma-mode = <UDMA_TR_MODE>;	\
+		statictr-type = <PSIL_STATIC_TR_XY>;	\
+	}
+
+#define UDMA_PDMA_PKT_XY(id)				\
+	ti,psil-config##id {				\
+		linux,udma-mode = <UDMA_PKT_MODE>;	\
+		statictr-type = <PSIL_STATIC_TR_XY>;	\
+	}
+
+#endif /* __DT_TI_UDMA_H */
include/linux/soc/ti/ti-udma.h new file +24 -0
new file mode 100644
index 000000000000..e9d4226c48d9
@@ -0,0 +1,24 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ *  Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com
+ *  Author: Peter Ujfalusi <[email protected]>
+ */
+
+#ifndef __TI_UDMA_H
+#define __TI_UDMA_H
+
+/**
+ * struct ti_udma_drv_packet_data - TI UDMA transfer specific data
+ *
+ * @pkt_type: Packet Type - specific for each DMA client HW
+ * @dest_tag: Destination tag The source pointer.
+ *
+ * TI UDMA transfer specific data passed as part of DMA transfer to
+ * the DMA client HW in UDMA descriptors.
+ */
+struct ti_udma_drv_packet_data {
+	u32	pkt_type;
+	u32	dest_tag;
+};
+
+#endif /* __TI_UDMA_H */
Signature · 1 line
2.20.1
#7 lore raw

PATCH v3 4/7 dma: ti: add driver to K3 UDMA

Quoted 15 lines · Vignesh R

The UDMA-P is intended to perform similar (but significantly upgraded) functions as the packet-oriented DMA used on previous SoC devices. The UDMA-P module supports the transmission and reception of various packet types. The UDMA-P also supports acting as both a UTC and UDMA-C for its internal channels. Channels in the UDMA-P can be configured to be either Packet-Based or Third-Party channels on a channel by channel basis.

The initial driver supports:
- MEM_TO_MEM (TR mode)
- DEV_TO_MEM (Packet mode)
- MEM_TO_DEV (Packet mode)

[snip]

Quoted 5 lines
drivers/dma/ti/k3-udma.c new file +5 -0
+#ifdef DEBUG
+#define	k3_udma_dbg(arg...) pr_err(arg)
+#define	k3_udma_dev_dbg(dev, arg...) dev_err(dev, arg)
+static void k3_udma_print_buf(ulong addr, const void *data, uint width,
+			      uint count, uint linelen)

drivers/dma/ti/k3-udma.c line 152

Quoted 10 lines
drivers/dma/ti/k3-udma.c new file +10 -0
+{
+	print_buffer(addr, data, width, count, linelen);
+}
+#else
+#define	k3_udma_dbg(arg...)
+#define	k3_udma_dev_dbg(arg...)
+static void k3_udma_print_buf(ulong addr, const void *data, uint width,
+			      uint count, uint linelen)
+{}
+#endif

Here too what I've just said in another part of the thread about pr_xxx and I sent in reply to another thread about print_buffer directly or not at all. Thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190201/6b37ab51/attachment.sig>
author maintainer
#8 lore raw

PATCH v3 5/7 soc: keystone: Merge into TI specific directory

In reply to Vignesh R

Merge drivers/soc/keystone/ into drivers/soc/ti/ and convert CONFIG_TI_KEYSTONE_SERDES into Kconfig.

---
 arch/arm/mach-keystone/Kconfig                 | 8 ++++++++
 drivers/soc/Makefile                           | 1 -
 drivers/soc/keystone/Makefile                  | 3 ---
 drivers/soc/ti/Kconfig                         | 6 ++++++
 drivers/soc/ti/Makefile                        | 5 ++---
 drivers/soc/{keystone => ti}/keystone_serdes.c | 0
 include/configs/ti_armv7_keystone2.h           | 3 ---
 scripts/config_whitelist.txt                   | 1 -
 8 files changed, 16 insertions(+), 11 deletions(-)
 delete mode 100644 drivers/soc/keystone/Makefile
 rename drivers/soc/{keystone => ti}/keystone_serdes.c (100%)
arch/arm/mach-keystone/Kconfig +8 -0
index d24596eccb0d..e06eba5aea1f 100644
@@ -9,18 +9,24 @@ config TARGET_K2HK_EVM
 	select SPL_BOARD_INIT if SPL
 	select CMD_DDR3
 	imply DM_I2C
+	imply SOC_TI
+	imply TI_KEYSTONE_SERDES
 
 config TARGET_K2E_EVM
 	bool "TI Keystone 2 Edison EVM"
 	select SPL_BOARD_INIT if SPL
 	select CMD_DDR3
 	imply DM_I2C
+	imply SOC_TI
+	imply TI_KEYSTONE_SERDES
 
 config TARGET_K2L_EVM
 	bool "TI Keystone 2 Lamar EVM"
 	select SPL_BOARD_INIT if SPL
 	select CMD_DDR3
 	imply DM_I2C
+	imply SOC_TI
+	imply TI_KEYSTONE_SERDES
 
 config TARGET_K2G_EVM
 	bool "TI Keystone 2 Galileo EVM"
@@ -29,6 +35,8 @@ config TARGET_K2G_EVM
         select TI_I2C_BOARD_DETECT
 	select CMD_DDR3
 	imply DM_I2C
+	imply SOC_TI
+	imply TI_KEYSTONE_SERDES
 
 endchoice
 
drivers/soc/Makefile +0 -1
index 8b7ead546e1c..ce253b7aa886 100644
@@ -2,5 +2,4 @@
 #
 # Makefile for the U-Boot SOC specific device drivers.
 
-obj-$(CONFIG_ARCH_KEYSTONE)	+= keystone/
 obj-$(CONFIG_SOC_TI) += ti/
drivers/soc/keystone/Makefile deleted +0 -3
deleted file mode 100644
index dfebb143e09b..000000000000
@@ -1,3 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-
-obj-$(CONFIG_TI_KEYSTONE_SERDES) += keystone_serdes.o
drivers/soc/ti/Kconfig +6 -0
index 8c0f3c07b23f..e4f88344487e 100644
@@ -16,5 +16,11 @@ config TI_K3_NAVSS_RINGACC
 	  and a consumer. There is one RINGACC module per NAVSS on TI AM65x SoCs
 	  If unsure, say N.
 
+config TI_KEYSTONE_SERDES
+	bool "Keystone SerDes driver for ethernet"
+	depends on ARCH_KEYSTONE
+	help
+	 SerDes driver for Keystone SoC used for ethernet support on TI
+	 K2 platforms.
 
 endif # SOC_TI
drivers/soc/ti/Makefile +2 -3
index 63e21aaad40f..4ec04ee1257e 100644
@@ -1,5 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0+
-#
-# TI K3 SOC drivers
-#
+
 obj-$(CONFIG_TI_K3_NAVSS_RINGACC)	+= k3-navss-ringacc.o
+obj-$(CONFIG_TI_KEYSTONE_SERDES)	+= keystone_serdes.o
drivers/soc/ti/keystone_serdes.c renamed from drivers/soc/keystone/keystone_serdes.c +0 -0
similarity index 100%
rename from drivers/soc/keystone/keystone_serdes.c
rename to drivers/soc/ti/keystone_serdes.c
include/configs/ti_armv7_keystone2.h +0 -3
index 0c7d66486832..6d8536a815f8 100644
@@ -134,9 +134,6 @@
 #define CONFIG_KSNET_SERDES_SGMII2_BASE		KS2_SGMII_SERDES2_BASE
 #define CONFIG_KSNET_SERDES_LANES_PER_SGMII	KS2_LANES_PER_SGMII_SERDES
 
-/* SerDes */
-#define CONFIG_TI_KEYSTONE_SERDES
-
 #define CONFIG_AEMIF_CNTRL_BASE		KS2_AEMIF_CNTRL_BASE
 
 /* I2C Configuration */
scripts/config_whitelist.txt +0 -1
index c05fc379645e..7a667ccbc3d2 100644
@@ -4420,7 +4420,6 @@ CONFIG_THOR_RESET_OFF
 CONFIG_THUNDERX
 CONFIG_TIMESTAMP
 CONFIG_TIZEN
-CONFIG_TI_KEYSTONE_SERDES
 CONFIG_TI_KSNAV
 CONFIG_TI_SPI_MMAP
 CONFIG_TMU_TIMER
Signature · 1 line
2.20.1
#9 lore raw

PATCH v3 5/7 soc: keystone: Merge into TI specific directory

Quoted 4 lines · Vignesh R

Merge drivers/soc/keystone/ into drivers/soc/ti/ and convert CONFIG_TI_KEYSTONE_SERDES into Kconfig.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190201/57a9a9ad/attachment.sig>
author maintainer
#10 lore raw

PATCH v3 6/7 arm64: dts: ti: k3-am65: add mcu navss nodes

In reply to Vignesh R

From: Grygorii Strashko <[email protected]>

Add DT node for MCU NAVSS its components to get DMA working on AM654 SoC.

---
 arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 46 ++++++++++++++++++++
 1 file changed, 46 insertions(+)
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +46 -0
index 143eb6d63092..5a934b106d04 100644
@@ -4,6 +4,7 @@
  */
 
 #include <dt-bindings/pinctrl/k3-am65.h>
+#include <dt-bindings/dma/k3-udma.h>
 
 / {
 	chosen {
@@ -63,6 +64,51 @@
 		pinctrl-single,register-width = <32>;
 		pinctrl-single,function-mask = <0xffffffff>;
 	};
+
+	navss_mcu: navss-mcu {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ti,sci-dev-id = <119>;
+
+		mcu_ringacc: ringacc at 2b800000 {
+			compatible = "ti,am654-navss-ringacc";
+			reg =	<0x0 0x2b800000 0x0 0x400000>,
+				<0x0 0x2b000000 0x0 0x400000>,
+				<0x0 0x28590000 0x0 0x100>,
+				<0x0 0x2a500000 0x0 0x40000>;
+			reg-names = "rt", "fifos",
+				    "proxy_gcfg", "proxy_target";
+			ti,num-rings = <286>;
+			ti,sci-rm-range-gp-rings = <0x2>; /* GP ring range */
+			ti,dma-ring-reset-quirk;
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <195>;
+		};
+
+		mcu_udmap: udmap at 285c0000 {
+			compatible = "ti,k3-navss-udmap";
+			reg =	<0x0 0x285c0000 0x0 0x100>,
+				<0x0 0x2a800000 0x0 0x40000>,
+				<0x0 0x2aa00000 0x0 0x40000>;
+			reg-names = "gcfg", "rchanrt", "tchanrt";
+			#dma-cells = <3>;
+
+			ti,ringacc = <&mcu_ringacc>;
+			ti,psil-base = <0x6000>;
+
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <194>;
+
+			ti,sci-rm-range-tchan = <0x1>, /* TX_HCHAN */
+						<0x2>; /* TX_CHAN */
+			ti,sci-rm-range-rchan = <0x3>, /* RX_HCHAN */
+						<0x4>; /* RX_CHAN */
+			ti,sci-rm-range-rflow = <0x5>; /* GP RFLOW */
+		};
+	};
 };
 
 &cbass_wakeup {
Signature · 1 line
2.20.1
#11 lore raw

PATCH v3 6/7 arm64: dts: ti: k3-am65: add mcu navss nodes

Quoted 7 lines · Vignesh R

From: Grygorii Strashko <[email protected]>

Add DT node for MCU NAVSS its components to get DMA working on AM654 SoC.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190201/24dc8b00/attachment.sig>
author maintainer
#12 lore raw

PATCH v3 7/7 configs: am65x_evm_a53: Enable DMA related configs

In reply to Vignesh R

From: Grygorii Strashko <[email protected]>

Enable TI K3 AM65x PSI-L, Ring Accelerator and UDMA drivers

---
 configs/am65x_evm_a53_defconfig | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
configs/am65x_evm_a53_defconfig +3 -1
index a17cf7cb5040..9ce22157c92d 100644
@@ -48,10 +48,11 @@ CONFIG_SPL_DM_SEQ_ALIAS=y
 CONFIG_CLK=y
 CONFIG_SPL_CLK=y
 CONFIG_CLK_TI_SCI=y
+CONFIG_DMA_CHANNELS=y
+CONFIG_TI_K3_NAVSS_UDMA=y
 CONFIG_TI_SCI_PROTOCOL=y
 CONFIG_DM_MAILBOX=y
 CONFIG_K3_SEC_PROXY=y
-CONFIG_MISC=y
 CONFIG_DM_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_K3_ARASAN=y
@@ -67,5 +68,6 @@ CONFIG_REMOTEPROC_K3=y
 CONFIG_DM_RESET=y
 CONFIG_RESET_TI_SCI=y
 CONFIG_DM_SERIAL=y
+CONFIG_SOC_TI=y
 CONFIG_SYSRESET=y
 CONFIG_SYSRESET_TI_SCI=y
Signature · 1 line
2.20.1
#13 lore raw

PATCH v3 7/7 configs: am65x_evm_a53: Enable DMA related configs

Quoted 6 lines · Vignesh R

From: Grygorii Strashko <[email protected]>

Enable TI K3 AM65x PSI-L, Ring Accelerator and UDMA drivers

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190201/ace6161c/attachment.sig>