Skip to contentSkip to conversation

board/raspberrypi: post-image customisations.

PATCH New Robert J. Heywood 3 participants 14 messages Jan 29, 2019 – Feb 11, 2019 Broadcom BCM2711/BCM2835 Arm architecture

lore
Share & tools
lore
#0 lore raw

cover board/raspberrypi: post-image customisations.

Hi all.

I wanted to do use u-boot and mainline kernel sources with my raspies but in trying to do so, found that doing it required a lot of changes to the genimage cfg files.
All the files were basically the same, and I found that they, and the post-image script define constants which are no longer correct if the corresponding options are changed in buildroot.
(eg. BR2_LINUX_KERNEL_INTREE_DTS_NAME)

I've improved the situation by first removing the replication in the cfg files (consolidating them into a single generic file). And then parsing the .config file for the board specific pieces; like the device tree files, and the kernel target (zimage vs image).

Then I added some new options;
- Adding files to the boot partition,
Allowing me to include uboot.bin.
- Changing the kernel in the config.txt file,
Allowing me to boot uboot.bin.
- Specifying a different rootfs file,
Since i would like to use btrfs instead of ext4.
- An option to skip creating the full sdimg.
As I'm using btrfs, in some cases I only need the vfat boot blob from genimage.

There are a couple of aspects you might find questionable that I would welcome comments on;

The script now modifies the generic genimage.cfg file and creates a temporary cfg file to be used with genimage. I've chosen to place the file at; ${BUILD_DIR}/genimage.cfg
This might not be the best choice.

I'm using a conbination of grep and eval to pull specific values out of the .config file and get them into the script. That might not be best practice.
Maybe theres a cleaner way of accessing those variables?

Kind regards,
~rob.

Robert J. Heywood (8):
board/raspberrypi: Unify the genimage config files board/raspberrypi: post-image --overlays option. board/raspberrypi: post-image, include .config dfs files. board/raspberrypi: post-image, include .config kernel target. board/raspberrypi: post-image --file option board/raspberrypi: post-image --rootfs option board/raspberrypi: post-image --skip-sdimg option board/raspberrypi: post-image --kernel option

 DEVELOPERS                                         |  3 ++
 ...rrypi2.cfg => genimage-raspberrypi-generic.cfg} |  7 +--
 board/raspberrypi/genimage-raspberrypi.cfg         | 32 ------------
 board/raspberrypi/genimage-raspberrypi0.cfg        | 30 ------------
 board/raspberrypi/genimage-raspberrypi0w.cfg       | 31 ------------
 board/raspberrypi/genimage-raspberrypi3-64.cfg     | 32 ------------
 board/raspberrypi/genimage-raspberrypi3.cfg        | 33 -------------
 board/raspberrypi/post-image.sh                    | 57 +++++++++++++++++++++-
 8 files changed, 62 insertions(+), 163 deletions(-)
 rename board/raspberrypi/{genimage-raspberrypi2.cfg => genimage-raspberrypi-generic.cfg} (85%)
 delete mode 100644 board/raspberrypi/genimage-raspberrypi.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi0.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi0w.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi3-64.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi3.cfg
Signature · 1 line
2.11.0
#1 lore raw

PATCH 1/8 board/raspberrypi: Unify the genimage config files

Add a new genimage config file containing all the common elements. The config file contains a marker which post-image.sh replaces with files defined in the board-specific .conf files.

Since I've substantially edited the way the post-image script works, I've added myself to the developers file for board/raspberrypi

---
 DEVELOPERS                                         |  3 ++
 ...rrypi2.cfg => genimage-raspberrypi-generic.cfg} |  3 +-
 board/raspberrypi/genimage-raspberrypi.cfg         | 32 ---------------------
 board/raspberrypi/genimage-raspberrypi0.cfg        | 30 --------------------
 board/raspberrypi/genimage-raspberrypi0w.cfg       | 31 --------------------
 board/raspberrypi/genimage-raspberrypi3-64.cfg     | 32 ---------------------
 board/raspberrypi/genimage-raspberrypi3.cfg        | 33 ----------------------
 board/raspberrypi/post-image.sh                    | 17 +++++++++--
 board/raspberrypi/raspberrypi.conf                 |  6 ++++
 board/raspberrypi/raspberrypi0.conf                |  4 +++
 board/raspberrypi/raspberrypi0w.conf               |  5 ++++
 board/raspberrypi/raspberrypi2.conf                |  4 +++
 board/raspberrypi/raspberrypi3-64.conf             |  6 ++++
 board/raspberrypi/raspberrypi3.conf                |  7 +++++
 14 files changed, 51 insertions(+), 162 deletions(-)
 rename board/raspberrypi/{genimage-raspberrypi2.cfg => genimage-raspberrypi-generic.cfg} (90%)
 delete mode 100644 board/raspberrypi/genimage-raspberrypi.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi0.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi0w.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi3-64.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi3.cfg
 create mode 100644 board/raspberrypi/raspberrypi.conf
 create mode 100644 board/raspberrypi/raspberrypi0.conf
 create mode 100644 board/raspberrypi/raspberrypi0w.conf
 create mode 100644 board/raspberrypi/raspberrypi2.conf
 create mode 100644 board/raspberrypi/raspberrypi3-64.conf
 create mode 100644 board/raspberrypi/raspberrypi3.conf
DEVELOPERS +3 -0
index c1950bb0f4..833adf8747 100644
@@ -1820,6 +1820,9 @@ F:	package/subversion/
 N:	RJ Ascani <[email protected]>
 F:	package/azmq/
 
+N:	Robert Heywood <[email protected]>
+F:	board/raspberrypi/
+
 N:	Robert Rose <[email protected]>
 F:	package/grpc/
 
board/raspberrypi/genimage-raspberrypi-generic.cfg renamed from board/raspberrypi/genimage-raspberrypi2.cfg +1 -2
similarity index 90%
rename from board/raspberrypi/genimage-raspberrypi2.cfg
rename to board/raspberrypi/genimage-raspberrypi-generic.cfg
index a3be2a3442..8bdd553a34 100644
@@ -1,13 +1,12 @@
 image boot.vfat {
   vfat {
     files = {
-      "bcm2709-rpi-2-b.dtb",
       "rpi-firmware/bootcode.bin",
       "rpi-firmware/cmdline.txt",
       "rpi-firmware/config.txt",
       "rpi-firmware/fixup.dat",
       "rpi-firmware/start.elf",
-      "zImage"
+      {BOOT_FILES}
     }
   }
   size = 32M
board/raspberrypi/genimage-raspberrypi.cfg deleted +0 -32
deleted file mode 100644
index bd5166a0f3..0000000000
@@ -1,32 +0,0 @@
-image boot.vfat {
-  vfat {
-    files = {
-      "bcm2708-rpi-b.dtb",
-      "bcm2708-rpi-b-plus.dtb",
-      "bcm2708-rpi-cm.dtb",
-      "rpi-firmware/bootcode.bin",
-      "rpi-firmware/cmdline.txt",
-      "rpi-firmware/config.txt",
-      "rpi-firmware/fixup.dat",
-      "rpi-firmware/start.elf",
-      "zImage"
-    }
-  }
-  size = 32M
-}
-
-image sdcard.img {
-  hdimage {
-  }
-
-  partition boot {
-    partition-type = 0xC
-    bootable = "true"
-    image = "boot.vfat"
-  }
-
-  partition rootfs {
-    partition-type = 0x83
-    image = "rootfs.ext4"
-  }
-}
board/raspberrypi/genimage-raspberrypi0.cfg deleted +0 -30
deleted file mode 100644
index a9d4c4501f..0000000000
@@ -1,30 +0,0 @@
-image boot.vfat {
-  vfat {
-    files = {
-      "bcm2708-rpi-b-plus.dtb",
-      "rpi-firmware/bootcode.bin",
-      "rpi-firmware/cmdline.txt",
-      "rpi-firmware/config.txt",
-      "rpi-firmware/fixup.dat",
-      "rpi-firmware/start.elf",
-      "zImage"
-    }
-  }
-  size = 32M
-}
-
-image sdcard.img {
-  hdimage {
-  }
-
-  partition boot {
-    partition-type = 0xC
-    bootable = "true"
-    image = "boot.vfat"
-  }
-
-  partition rootfs {
-    partition-type = 0x83
-    image = "rootfs.ext4"
-  }
-}
board/raspberrypi/genimage-raspberrypi0w.cfg deleted +0 -31
deleted file mode 100644
index 3aafd9b6fc..0000000000
@@ -1,31 +0,0 @@
-image boot.vfat {
-  vfat {
-    files = {
-      "bcm2708-rpi-0-w.dtb",
-      "rpi-firmware/bootcode.bin",
-      "rpi-firmware/cmdline.txt",
-      "rpi-firmware/config.txt",
-      "rpi-firmware/fixup.dat",
-      "rpi-firmware/start.elf",
-      "rpi-firmware/overlays",
-      "zImage"
-    }
-  }
-  size = 32M
-}
-
-image sdcard.img {
-  hdimage {
-  }
-
-  partition boot {
-    partition-type = 0xC
-    bootable = "true"
-    image = "boot.vfat"
-  }
-
-  partition rootfs {
-    partition-type = 0x83
-    image = "rootfs.ext4"
-  }
-}
board/raspberrypi/genimage-raspberrypi3-64.cfg deleted +0 -32
deleted file mode 100644
index 0d0ca750a7..0000000000
@@ -1,32 +0,0 @@
-image boot.vfat {
-  vfat {
-    files = {
-      "bcm2710-rpi-3-b.dtb",
-      "bcm2710-rpi-3-b-plus.dtb",
-      "bcm2837-rpi-3-b.dtb",
-      "rpi-firmware/bootcode.bin",
-      "rpi-firmware/cmdline.txt",
-      "rpi-firmware/config.txt",
-      "rpi-firmware/fixup.dat",
-      "rpi-firmware/start.elf",
-      "Image"
-    }
-  }
-  size = 32M
-}
-
-image sdcard.img {
-  hdimage {
-  }
-
-  partition boot {
-    partition-type = 0xC
-    bootable = "true"
-    image = "boot.vfat"
-  }
-
-  partition rootfs {
-    partition-type = 0x83
-    image = "rootfs.ext4"
-  }
-}
board/raspberrypi/genimage-raspberrypi3.cfg deleted +0 -33
deleted file mode 100644
index 0a547241f4..0000000000
@@ -1,33 +0,0 @@
-image boot.vfat {
-  vfat {
-    files = {
-      "bcm2710-rpi-3-b.dtb",
-      "bcm2710-rpi-3-b-plus.dtb",
-      "bcm2710-rpi-cm3.dtb",
-      "rpi-firmware/bootcode.bin",
-      "rpi-firmware/cmdline.txt",
-      "rpi-firmware/config.txt",
-      "rpi-firmware/fixup.dat",
-      "rpi-firmware/start.elf",
-      "rpi-firmware/overlays",
-      "zImage"
-    }
-  }
-  size = 32M
-}
-
-image sdcard.img {
-  hdimage {
-  }
-
-  partition boot {
-    partition-type = 0xC
-    bootable = "true"
-    image = "boot.vfat"
-  }
-
-  partition rootfs {
-    partition-type = 0x83
-    image = "rootfs.ext4"
-  }
-}
board/raspberrypi/post-image.sh +15 -2
index 70447cd48b..4042c5e9ac 100755
@@ -4,9 +4,14 @@ set -e
 
 BOARD_DIR="$(dirname $0)"
 BOARD_NAME="$(basename ${BOARD_DIR})"
-GENIMAGE_CFG="${BOARD_DIR}/genimage-${BOARD_NAME}.cfg"
+GENIMAGE_CFG="${BOARD_DIR}/genimage-raspberrypi-generic.cfg"
 GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
 
+if [ -e ${BOARD_DIR}/${BOARD_NAME}.conf ]
+then
+	. ${BOARD_DIR}/${BOARD_NAME}.conf
+fi
+
 for arg in "$@"
 do
 	case "${arg}" in
@@ -49,6 +54,14 @@ __EOF__
 
 done
 
+for i in ${!FILES[*]}
+do
+	FILES[$i]="\"${FILES[$i]}\","
+done
+SEDCMD_BOOTFILES=" -e 's/{BOOT_FILES}/${FILES[*]}/' "
+
+eval "sed ${SEDCMD_BOOTFILES} ${GENIMAGE_CFG}" > ${BUILD_DIR}/genimage.cfg
+
 rm -rf "${GENIMAGE_TMP}"
 
 genimage                           \
@@ -56,6 +69,6 @@ genimage                           \
 	--tmppath "${GENIMAGE_TMP}"    \
 	--inputpath "${BINARIES_DIR}"  \
 	--outputpath "${BINARIES_DIR}" \
-	--config "${GENIMAGE_CFG}"
+	--config "${BUILD_DIR}/genimage.cfg"
 
 exit $?
board/raspberrypi/raspberrypi.conf new file +6 -0
new file mode 100644
index 0000000000..962cf726e2
@@ -0,0 +1,6 @@
+FILES=(
+	"bcm2708-rpi-b.dtb"
+	"bcm2708-rpi-b-plus.dtb"
+	"bcm2708-rpi-cm.dtb"
+	"zImage"
+)
board/raspberrypi/raspberrypi0.conf new file +4 -0
new file mode 100644
index 0000000000..132540b543
@@ -0,0 +1,4 @@
+FILES=(
+	"bcm2708-rpi-b-plus.dtb"
+	"zImage"
+)
board/raspberrypi/raspberrypi0w.conf new file +5 -0
new file mode 100644
index 0000000000..1ae60ed8fb
@@ -0,0 +1,5 @@
+FILES=(
+	"bcm2708-rpi-0-w.dtb"
+	"rpi-firmware/overlays"
+	"zImage"
+)
board/raspberrypi/raspberrypi2.conf new file +4 -0
new file mode 100644
index 0000000000..ea7d2402a6
@@ -0,0 +1,4 @@
+FILES=(
+	"bcm2709-rpi-2-b.dtb"
+	"zImage"
+)
board/raspberrypi/raspberrypi3-64.conf new file +6 -0
new file mode 100644
index 0000000000..11cb88e191
@@ -0,0 +1,6 @@
+FILES=(
+	"bcm2710-rpi-3-b.dtb"
+	"bcm2710-rpi-3-b-plus.dtb"
+	"bcm2837-rpi-3-b.dtb"
+	"Image"
+)
board/raspberrypi/raspberrypi3.conf new file +7 -0
new file mode 100644
index 0000000000..b3c5466fc2
@@ -0,0 +1,7 @@
+FILES=(
+	"bcm2710-rpi-3-b.dtb"
+	"bcm2710-rpi-3-b-plus.dtb"
+	"bcm2710-rpi-cm3.dtb"
+	"rpi-firmware/overlays"
+	"zImage"
+)
Signature · 1 line
2.11.0
#2 lore raw

PATCH 2/8 board/raspberrypi: post-image --overlays option.

In reply to Robert J. Heywood

Pull the device tree overlays into the boot partition if the --overlays option is set.
In addition, --add-pi3-miniuart-bt-overlay now implies --overlays.

Since the board conf files no longer need to explicitly declare the overlays, the line including the overlays were removed from raspberrypi0w.conf and raspberrypi3.conf

---
 board/raspberrypi/post-image.sh      | 9 +++++++++
 board/raspberrypi/raspberrypi0w.conf | 1 -
 board/raspberrypi/raspberrypi3.conf  | 1 -
 3 files changed, 9 insertions(+), 2 deletions(-)
board/raspberrypi/post-image.sh +9 -0
index 4042c5e9ac..5cc25a9ac6 100755
@@ -6,6 +6,7 @@ BOARD_DIR="$(dirname $0)"
 BOARD_NAME="$(basename ${BOARD_DIR})"
 GENIMAGE_CFG="${BOARD_DIR}/genimage-raspberrypi-generic.cfg"
 GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
+INCLUDE_OVERLAYS=false
 
 if [ -e ${BOARD_DIR}/${BOARD_NAME}.conf ]
 then
@@ -23,8 +24,12 @@ do
 # fixes rpi3 ttyAMA0 serial console
 dtoverlay=pi3-miniuart-bt
 __EOF__
+			INCLUDE_OVERLAYS=true
 		fi
 		;;
+		--overlays)
+			INCLUDE_OVERLAYS=true
+		;;
 		--aarch64)
 		# Run a 64bits kernel (armv8)
 		sed -e '/^kernel=/s,=.*,=Image,' -i "${BINARIES_DIR}/rpi-firmware/config.txt"
@@ -54,6 +59,10 @@ __EOF__
 
 done
 
+if $INCLUDE_OVERLAYS; then
+	FILES+=( "rpi-firmware/overlays" )
+fi
+
 for i in ${!FILES[*]}
 do
 	FILES[$i]="\"${FILES[$i]}\","
board/raspberrypi/raspberrypi0w.conf +0 -1
index 1ae60ed8fb..27b4ec2399 100644
@@ -1,5 +1,4 @@
 FILES=(
 	"bcm2708-rpi-0-w.dtb"
-	"rpi-firmware/overlays"
 	"zImage"
 )
board/raspberrypi/raspberrypi3.conf +0 -1
index b3c5466fc2..51df913860 100644
@@ -2,6 +2,5 @@ FILES=(
 	"bcm2710-rpi-3-b.dtb"
 	"bcm2710-rpi-3-b-plus.dtb"
 	"bcm2710-rpi-cm3.dtb"
-	"rpi-firmware/overlays"
 	"zImage"
 )
Signature · 1 line
2.11.0
#3 lore raw

PATCH 3/8 board/raspberrypi: post-image, include .config dfs files.

In reply to Robert J. Heywood

This change pulls dts filenames from the .config file instead of specifying the required dts files in a board config file. This reduces duplication and makes it possible to specify different dts files in the config file to have it appear in the resultant image. You would want to do so if you were using mainline kernel sources.

The device tree declarations were removed from the board .conf files.

---
 board/raspberrypi/post-image.sh        | 7 +++++++
 board/raspberrypi/raspberrypi.conf     | 3 ---
 board/raspberrypi/raspberrypi0.conf    | 1 -
 board/raspberrypi/raspberrypi0w.conf   | 1 -
 board/raspberrypi/raspberrypi2.conf    | 1 -
 board/raspberrypi/raspberrypi3-64.conf | 3 ---
 board/raspberrypi/raspberrypi3.conf    | 3 ---
 7 files changed, 7 insertions(+), 12 deletions(-)
board/raspberrypi/post-image.sh +7 -0
index 5cc25a9ac6..900bf1eae2 100755
@@ -63,6 +63,13 @@ if $INCLUDE_OVERLAYS; then
 	FILES+=( "rpi-firmware/overlays" )
 fi
 
+# Pull device tree names from the .config file.
+eval `grep BR2_LINUX_KERNEL_INTREE_DTS_NAME .config`
+for dts in $BR2_LINUX_KERNEL_INTREE_DTS_NAME
+do
+	FILES+=( "$(basename $dts).dtb" )
+done
+
 for i in ${!FILES[*]}
 do
 	FILES[$i]="\"${FILES[$i]}\","
board/raspberrypi/raspberrypi.conf +0 -3
index 962cf726e2..7b511fd0fc 100644
@@ -1,6 +1,3 @@
 FILES=(
-	"bcm2708-rpi-b.dtb"
-	"bcm2708-rpi-b-plus.dtb"
-	"bcm2708-rpi-cm.dtb"
 	"zImage"
 )
board/raspberrypi/raspberrypi0.conf +0 -1
index 132540b543..7b511fd0fc 100644
@@ -1,4 +1,3 @@
 FILES=(
-	"bcm2708-rpi-b-plus.dtb"
 	"zImage"
 )
board/raspberrypi/raspberrypi0w.conf +0 -1
index 27b4ec2399..7b511fd0fc 100644
@@ -1,4 +1,3 @@
 FILES=(
-	"bcm2708-rpi-0-w.dtb"
 	"zImage"
 )
board/raspberrypi/raspberrypi2.conf +0 -1
index ea7d2402a6..7b511fd0fc 100644
@@ -1,4 +1,3 @@
 FILES=(
-	"bcm2709-rpi-2-b.dtb"
 	"zImage"
 )
board/raspberrypi/raspberrypi3-64.conf +0 -3
index 11cb88e191..6e810367d0 100644
@@ -1,6 +1,3 @@
 FILES=(
-	"bcm2710-rpi-3-b.dtb"
-	"bcm2710-rpi-3-b-plus.dtb"
-	"bcm2837-rpi-3-b.dtb"
 	"Image"
 )
board/raspberrypi/raspberrypi3.conf +0 -3
index 51df913860..7b511fd0fc 100644
@@ -1,6 +1,3 @@
 FILES=(
-	"bcm2710-rpi-3-b.dtb"
-	"bcm2710-rpi-3-b-plus.dtb"
-	"bcm2710-rpi-cm3.dtb"
 	"zImage"
 )
Signature · 1 line
2.11.0
#4 lore raw

PATCH 4/8 board/raspberrypi: post-image, include .config kernel target.

In reply to Robert J. Heywood

Read the .config file to find if either a zImage or an Image is being built, and include them in the final fat volume if so.

This change means that the config files specific for each version of the pi are now empty. So they are removed.

---
 board/raspberrypi/post-image.sh        | 9 +++++++++
 board/raspberrypi/raspberrypi.conf     | 3 ---
 board/raspberrypi/raspberrypi0.conf    | 3 ---
 board/raspberrypi/raspberrypi0w.conf   | 3 ---
 board/raspberrypi/raspberrypi2.conf    | 3 ---
 board/raspberrypi/raspberrypi3-64.conf | 3 ---
 board/raspberrypi/raspberrypi3.conf    | 3 ---
 7 files changed, 9 insertions(+), 18 deletions(-)
 delete mode 100644 board/raspberrypi/raspberrypi.conf
 delete mode 100644 board/raspberrypi/raspberrypi0.conf
 delete mode 100644 board/raspberrypi/raspberrypi0w.conf
 delete mode 100644 board/raspberrypi/raspberrypi2.conf
 delete mode 100644 board/raspberrypi/raspberrypi3-64.conf
 delete mode 100644 board/raspberrypi/raspberrypi3.conf
board/raspberrypi/post-image.sh +9 -0
index 900bf1eae2..c082dada3c 100755
@@ -70,6 +70,15 @@ do
 	FILES+=( "$(basename $dts).dtb" )
 done
 
+# Pull the kernel target from the .config file.
+eval `egrep '^BR2_LINUX_KERNEL_Z?IMAGE=y$' .config`
+if [ "${BR2_LINUX_KERNEL_IMAGE}" = 'y' ]; then
+	FILES+=( "Image" )
+fi
+if [ "${BR2_LINUX_KERNEL_ZIMAGE}" = 'y' ]; then
+	FILES+=( "zImage" )
+fi
+
 for i in ${!FILES[*]}
 do
 	FILES[$i]="\"${FILES[$i]}\","
board/raspberrypi/raspberrypi.conf deleted +0 -3
deleted file mode 100644
index 7b511fd0fc..0000000000
@@ -1,3 +0,0 @@
-FILES=(
-	"zImage"
-)
board/raspberrypi/raspberrypi0.conf deleted +0 -3
deleted file mode 100644
index 7b511fd0fc..0000000000
@@ -1,3 +0,0 @@
-FILES=(
-	"zImage"
-)
board/raspberrypi/raspberrypi0w.conf deleted +0 -3
deleted file mode 100644
index 7b511fd0fc..0000000000
@@ -1,3 +0,0 @@
-FILES=(
-	"zImage"
-)
board/raspberrypi/raspberrypi2.conf deleted +0 -3
deleted file mode 100644
index 7b511fd0fc..0000000000
@@ -1,3 +0,0 @@
-FILES=(
-	"zImage"
-)
board/raspberrypi/raspberrypi3-64.conf deleted +0 -3
deleted file mode 100644
index 6e810367d0..0000000000
@@ -1,3 +0,0 @@
-FILES=(
-	"Image"
-)
board/raspberrypi/raspberrypi3.conf deleted +0 -3
deleted file mode 100644
index 7b511fd0fc..0000000000
@@ -1,3 +0,0 @@
-FILES=(
-	"zImage"
-)
Signature · 1 line
2.11.0
#5 lore raw

PATCH 5/8 board/raspberrypi: post-image --file option

In reply to Robert J. Heywood

Add a mechanism for adding files to the boot partition.

Usage: --file=example.txt

---
 board/raspberrypi/post-image.sh | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
board/raspberrypi/post-image.sh +4 -1
index c082dada3c..7e39399187 100755
@@ -55,6 +55,9 @@ __EOF__
 		gpu_mem="${arg:2}"
 		sed -e "/^${gpu_mem%=*}=/s,=.*,=${gpu_mem##*=}," -i "${BINARIES_DIR}/rpi-firmware/config.txt"
 		;;
+		--file=*)
+		FILES+=("${arg:7}")
+		;;
 	esac
 
 done
@@ -81,7 +84,7 @@ fi
 
 for i in ${!FILES[*]}
 do
-	FILES[$i]="\"${FILES[$i]}\","
+	FILES[$i]=$(echo "\"${FILES[$i]}\"," | sed -e 's/[\/&]/\\&/g')
 done
 SEDCMD_BOOTFILES=" -e 's/{BOOT_FILES}/${FILES[*]}/' "
 
Signature · 1 line
2.11.0
#6 lore raw

PATCH 6/8 board/raspberrypi: post-image --rootfs option

In reply to Robert J. Heywood

Add an option to change the rootfs. This option is useful if you would like to create an image using something other than ext4.

Usage: --rootfs=example

---
 board/raspberrypi/genimage-raspberrypi-generic.cfg | 2 +-
 board/raspberrypi/post-image.sh                    | 7 ++++++-
 2 files changed, 7 insertions(+), 2 deletions(-)
board/raspberrypi/genimage-raspberrypi-generic.cfg +1 -1
index 8bdd553a34..96020a5ddc 100644
@@ -24,6 +24,6 @@ image sdcard.img {
 
   partition rootfs {
     partition-type = 0x83
-    image = "rootfs.ext4"
+    image = "{ROOTFS}"
   }
 }
board/raspberrypi/post-image.sh +6 -1
index 7e39399187..77118deafd 100755
@@ -7,6 +7,7 @@ BOARD_NAME="$(basename ${BOARD_DIR})"
 GENIMAGE_CFG="${BOARD_DIR}/genimage-raspberrypi-generic.cfg"
 GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
 INCLUDE_OVERLAYS=false
+ROOTFS="rootfs.ext4"
 
 if [ -e ${BOARD_DIR}/${BOARD_NAME}.conf ]
 then
@@ -58,6 +59,9 @@ __EOF__
 		--file=*)
 		FILES+=("${arg:7}")
 		;;
+		--rootfs=*)
+		ROOTFS="${arg:9}"
+		;;
 	esac
 
 done
@@ -87,8 +91,9 @@ do
 	FILES[$i]=$(echo "\"${FILES[$i]}\"," | sed -e 's/[\/&]/\\&/g')
 done
 SEDCMD_BOOTFILES=" -e 's/{BOOT_FILES}/${FILES[*]}/' "
+SEDCMD_ROOTFS=" -e 's/{ROOTFS}/${ROOTFS}/' "
 
-eval "sed ${SEDCMD_BOOTFILES} ${GENIMAGE_CFG}" > ${BUILD_DIR}/genimage.cfg
+eval "sed ${SEDCMD_BOOTFILES} ${SEDCMD_ROOTFS} ${GENIMAGE_CFG}" > ${BUILD_DIR}/genimage.cfg
 
 rm -rf "${GENIMAGE_TMP}"
 
Signature · 1 line
2.11.0
#7 lore raw

PATCH 7/8 board/raspberrypi: post-image --skip-sdimg option

In reply to Robert J. Heywood

Add an option to disable the sd-card.img.
This is useful for when youre not building any compatible rootfs.

---
 board/raspberrypi/genimage-raspberrypi-generic.cfg | 2 ++
 board/raspberrypi/post-image.sh                    | 6 +++++-
 2 files changed, 7 insertions(+), 1 deletion(-)
board/raspberrypi/genimage-raspberrypi-generic.cfg +2 -0
index 96020a5ddc..91f5039fb8 100644
@@ -12,6 +12,7 @@ image boot.vfat {
   size = 32M
 }
 
+{SDIMG_START}
 image sdcard.img {
   hdimage {
   }
@@ -27,3 +28,4 @@ image sdcard.img {
     image = "{ROOTFS}"
   }
 }
+{SDIMG_END}
board/raspberrypi/post-image.sh +5 -1
index 77118deafd..dbcaf3b1f8 100755
@@ -8,6 +8,7 @@ GENIMAGE_CFG="${BOARD_DIR}/genimage-raspberrypi-generic.cfg"
 GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
 INCLUDE_OVERLAYS=false
 ROOTFS="rootfs.ext4"
+SEDCMD_SDIMG=" -e '/{SDIMG_.*}/d' "
 
 if [ -e ${BOARD_DIR}/${BOARD_NAME}.conf ]
 then
@@ -62,6 +63,9 @@ __EOF__
 		--rootfs=*)
 		ROOTFS="${arg:9}"
 		;;
+		--skip-sdimg)
+		SEDCMD_SDIMG=" -e '/{SDIMG_START}/,/{SDIMG_END}/d' "
+		;;
 	esac
 
 done
@@ -93,7 +97,7 @@ done
 SEDCMD_BOOTFILES=" -e 's/{BOOT_FILES}/${FILES[*]}/' "
 SEDCMD_ROOTFS=" -e 's/{ROOTFS}/${ROOTFS}/' "
 
-eval "sed ${SEDCMD_BOOTFILES} ${SEDCMD_ROOTFS} ${GENIMAGE_CFG}" > ${BUILD_DIR}/genimage.cfg
+eval "sed ${SEDCMD_BOOTFILES} ${SEDCMD_ROOTFS} ${SEDCMD_SDIMG} ${GENIMAGE_CFG}" > ${BUILD_DIR}/genimage.cfg
 
 rm -rf "${GENIMAGE_TMP}"
 
Signature · 1 line
2.11.0
#8 lore raw

PATCH 8/8 board/raspberrypi: post-image --kernel option

In reply to Robert J. Heywood

Add an option to specify the kernel to boot.
This can be used to enable uboot on the pi.

---
 board/raspberrypi/post-image.sh | 3 +++
 1 file changed, 3 insertions(+)
board/raspberrypi/post-image.sh +3 -0
index dbcaf3b1f8..71d9857f09 100755
@@ -66,6 +66,9 @@ __EOF__
 		--skip-sdimg)
 		SEDCMD_SDIMG=" -e '/{SDIMG_START}/,/{SDIMG_END}/d' "
 		;;
+		--kernel=*)
+		sed -e "/^kernel=/s,=.*,=${arg:9}," -i "${BINARIES_DIR}/rpi-firmware/config.txt"
+		;;
 	esac
 
 done
Signature · 1 line
2.11.0
#9 lore raw

cover board/raspberrypi: post-image customisations.

In reply to Robert J. Heywood

Hi Robert,

Thank you for this work, excellent to see the raspberrypi support improved. We
discussed this at the Buildroot developer meeting.

However, we would like to suggest a slightly different approach that is more
amenable to reuse in other context and also simplifies things in general, we think. See below for our thoughts and suggestions. Thus, the series is marked as Changes Requested in patchwork.

Quoted 5 lines · Robert J. Heywood

Hi all.

I wanted to do use u-boot and mainline kernel sources with my raspies but in trying to do so, found that doing it required a lot of changes to the genimage cfg files.

Note that the intention is actually that when you change the configuration of
your target, you also change the genimage.cfg file. That said, if it is easy to support more use cases with a single genimage.cfg file (especially if there are in-tree use cases as well), that is something we might want to support in the provided genimage.cfg files.

Quoted 9 lines

All the files were basically the same, and I found that they, and the post-image script define constants which are no longer correct if the corresponding options are changed in buildroot.
(eg. BR2_LINUX_KERNEL_INTREE_DTS_NAME)

I've improved the situation by first removing the replication in the cfg files (consolidating them into a single generic file). And then parsing the .config file for the board specific pieces; like the device tree files, and the kernel target (zimage vs image).

This .config approach we don't like. Instead, we think it is more appropriate
to add support for wildcards to genimage itself (and send that change upstream to pengutronix as well). That way, you can add "*.dtb" to genimage.cfg instead of the current board-specific names.

This approach can then be reused for other boards as well, like the freescale
boards on which you probably based this approach. Back in the day that approach of a post-image script that autodiscovers things looked like the right thing to do, but it is actually somewhat complicated and confusing.

Quoted 4 lines

Then I added some new options;
- Adding files to the boot partition,
Allowing me to include uboot.bin.

If you want to do something like this, I really think it's more appropriate to
make a custom genimage.cfg and config.txt that includes everything you want. Note that if you make a custom genimage.cfg, you also don't need to use the raspberrypi post-image script. Instead, use support/scripts/genimage.sh as the post-image script.

For the zImage vs. image, you could use "*mage" but I actually think it's more
appropriate to keep separate genimage.cfg files for them.

Quoted 2 lines

- Changing the kernel in the config.txt file,
Allowing me to boot uboot.bin.

Cfr. above.

In fact, I don't really like the way the post-image script is updating the
config.txt. I think it makes much more sense to have a different config.txt for each board instead of SEDing it. There are two options to handle this: either copy the board-specific config.txt in the post-image script, or (more generically) extend support/scripts/genimage.cfg with options that point to directories/files that have to be copied to IMAGES_DIR before running genimage.

Quoted 2 lines

- Specifying a different rootfs file, Since i would like to use btrfs instead of ext4.

This one certainly is better done in a custom genimage.cfg.

Quoted 3 lines

- An option to skip creating the full sdimg.
As I'm using btrfs, in some cases I only need the vfat boot blob from genimage.

Again, make a custom genimage.cfg.

Quoted 7 lines

There are a couple of aspects you might find questionable that I would welcome comments on;

The script now modifies the generic genimage.cfg file and creates a temporary cfg file to be used with genimage. I've chosen to place the file at; ${BUILD_DIR}/genimage.cfg
This might not be the best choice.

The freescale scripts now use mktemp, but actually I prefer your choice of
putting it in BUILD_DIR.

Quoted 3 lines

I'm using a conbination of grep and eval to pull specific values out of the .config file and get them into the script. That might not be best practice.

I personally prefer to use 'make printvars VARS=...' because you can also
extract make-derived variables that way (e.g. LINUX_IMAGE_NAME to get the zImage/image). But either way is fine.

Regards,
Arnout

Quoted 31 lines

Maybe theres a cleaner way of accessing those variables?

Kind regards,
~rob.

Robert J. Heywood (8):
board/raspberrypi: Unify the genimage config files board/raspberrypi: post-image --overlays option. board/raspberrypi: post-image, include .config dfs files. board/raspberrypi: post-image, include .config kernel target. board/raspberrypi: post-image --file option board/raspberrypi: post-image --rootfs option board/raspberrypi: post-image --skip-sdimg option board/raspberrypi: post-image --kernel option

 DEVELOPERS                                         |  3 ++
 ...rrypi2.cfg => genimage-raspberrypi-generic.cfg} |  7 +--
 board/raspberrypi/genimage-raspberrypi.cfg         | 32 ------------
 board/raspberrypi/genimage-raspberrypi0.cfg        | 30 ------------
 board/raspberrypi/genimage-raspberrypi0w.cfg       | 31 ------------
 board/raspberrypi/genimage-raspberrypi3-64.cfg     | 32 ------------
 board/raspberrypi/genimage-raspberrypi3.cfg        | 33 -------------
 board/raspberrypi/post-image.sh                    | 57 +++++++++++++++++++++-
 8 files changed, 62 insertions(+), 163 deletions(-)
 rename board/raspberrypi/{genimage-raspberrypi2.cfg => genimage-raspberrypi-generic.cfg} (85%)
 delete mode 100644 board/raspberrypi/genimage-raspberrypi.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi0.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi0w.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi3-64.cfg
 delete mode 100644 board/raspberrypi/genimage-raspberrypi3.cfg
#10 lore raw

cover board/raspberrypi: post-image customisations.

Hi Arnout.

Thanks for your reply.
In retrospect I probably should have reached out and asked if any of this would be wanted prior to submitting it. c?est la vie.

Quoted 11 lines · Arnout Vandecappelle

Hi Robert,

Thank you for this work, excellent to see the raspberrypi support improved. We
discussed this at the Buildroot developer meeting.

However, we would like to suggest a slightly different approach that is more
amenable to reuse in other context and also simplifies things in general, we think. See below for our thoughts and suggestions. Thus, the series is marked as Changes Requested in patchwork.

On 29/01/2019 14:23, Robert J. Heywood wrote:

Quoted 8 lines
Quoted 5 lines

Hi all.

I wanted to do use u-boot and mainline kernel sources with my raspies but in trying to do so, found that doing it required a lot of changes to the genimage cfg files.

Note that the intention is actually that when you change the configuration of
your target, you also change the genimage.cfg file.

This is something that I found pretty confusing. It seems illogical to have to set the same options in two distinct places.

Quoted 5 lines

That said, if it is easy to
support more use cases with a single genimage.cfg file (especially if there are in-tree use cases as well), that is something we might want to support in the provided genimage.cfg files.

It would be better if the genimage config file could contain a placeholder, such as "devicetree" or "kernel" which could then be specified on the commandline. Then when buildroot calls genimage, it could fill in the relevant parameters.

It would simplify a lot of the cfg files across all of the boards.

Quoted 11 lines
Quoted 5 lines

--snip--
I've improved the situation by first removing the replication in the cfg files (consolidating them into a single generic file). And then parsing the .config file for the board specific pieces; like the device tree files, and the kernel target (zimage vs image).

This .config approach we don't like. Instead, we think it is more appropriate
to add support for wildcards to genimage itself (and send that change upstream to pengutronix as well). That way, you can add "*.dtb" to genimage.cfg instead of the current board-specific names.

genimage sort of already has this feature for directories. It's a shame we cant use that feature here, since the pi's bootloader uses device trees in the root of the partition. It would have been nice to have a dtb folder.

Quoted 4 lines

This approach can then be reused for other boards as well, like the freescale
boards on which you probably based this approach. Back in the day that approach of a post-image script that autodiscovers things looked like the right thing to do, but it is actually somewhat complicated and confusing.

I wasn't aware the freescale configs did something similar. That's pretty interesting.

Quoted 7 lines

If you want to do something like this, I really think it's more appropriate to
make a custom genimage.cfg and config.txt that includes everything you want. Note that if you make a custom genimage.cfg, you also don't need to use the raspberrypi post-image script. Instead, use support/scripts/genimage.sh as the post-image script.

Quoted 7 lines

For the zImage vs. image, you could use "*mage" but I actually think it's more
appropriate to keep separate genimage.cfg files for them.

Quoted 2 lines

- Changing the kernel in the config.txt file,
Allowing me to boot uboot.bin.

Cfr. above.

I was really hoping I'd be able to get away with not having to maintain a separate set of files outside of buildroot that basically just replicate functionality already inside of it.
But I guess what I could do is setup my CI such that it watches the buildroot genimage.cfg files and alerts me if any incompatible changes happen.

Quoted 7 lines

In fact, I don't really like the way the post-image script is updating the
config.txt. I think it makes much more sense to have a different config.txt for each board instead of SEDing it. There are two options to handle this: either copy the board-specific config.txt in the post-image script, or (more generically) extend support/scripts/genimage.cfg with options that point to directories/files that have to be copied to IMAGES_DIR before running genimage.

I enjoy the sed approach. It means buildroot is able to take advantage of upstream changes to the config.txt file, and we're not made to maintain a hoard of copies with minor changes.

Quoted 4 lines
Quoted 3 lines

- Specifying a different rootfs file,
Since i would like to use btrfs instead of ext4.

Quoted 8 lines

This one certainly is better done in a custom genimage.cfg.

Quoted 3 lines

- An option to skip creating the full sdimg.
As I'm using btrfs, in some cases I only need the vfat boot blob from genimage.

Again, make a custom genimage.cfg.

very well.

I have a script that configures buildroot as I want it, from defconfigs and fragments. I'll also make it spit out a genimage file.
It'll be easy to do there since that script has access to the devicetree/kernel variables from the defconfig anyway.

Quoted 8 lines
Quoted 4 lines

I'm using a conbination of grep and eval to pull specific values out of the .config file and get them into the script. That might not be best practice.

I personally prefer to use 'make printvars VARS=...' because you can also
extract make-derived variables that way (e.g. LINUX_IMAGE_NAME to get the zImage/image). But either way is fine.

I think I'll use that from now on. I find the eval approach confusing to look at. :)

kind regards, rob.

#11 lore raw

cover board/raspberrypi: post-image customisations.

Quoted 25 lines · Robert Heywood

Hi Arnout.

Thanks for your reply.
In retrospect I probably should have reached out and asked if any of this would be wanted prior to submitting it. c?est la vie.

Quoted 17 lines · Arnout Vandecappelle

? Hi Robert,

? Thank you for this work, excellent to see the raspberrypi support improved. We discussed this at the Buildroot developer meeting.

? However, we would like to suggest a slightly different approach that is more amenable to reuse in other context and also simplifies things in general, we think. See below for our thoughts and suggestions. Thus, the series is marked as Changes Requested in patchwork.

Quoted 5 lines · Robert J. Heywood

Hi all.

I wanted to do use u-boot and mainline kernel sources with my raspies but in trying to do so, found that doing it required a lot of changes to the genimage cfg files.

Quoted 5 lines
Quoted 2 lines

? Note that the intention is actually that when you change the configuration of your target, you also change the genimage.cfg file.

This is something that I found pretty confusing. It seems illogical to have to set the same options in two distinct places.

True, but this patch series doesn't really change that, does it? E.g. for the
zImage/image kernel, you still have to select both the correct BR2_LINUX_KERNEL_xxIMAGE option and pass --kernel= (rather than updating config.txt).

Quoted 9 lines
Quoted 5 lines

That said, if it is easy to
support more use cases with a single genimage.cfg file (especially if there are in-tree use cases as well), that is something we might want to support in the provided genimage.cfg files.

It would be better if the genimage config file could contain a placeholder, such as "devicetree" or "kernel" which could then be specified on the commandline. Then when buildroot calls genimage, it could fill in the relevant parameters.

That is indeed a good idea! Maybe both better and easier to implement than
wildcard support in genimage...

Quoted 56 lines

It would simplify a lot of the cfg files across all of the boards.

Quoted 11 lines
Quoted 5 lines

--snip--
I've improved the situation by first removing the replication in the cfg files (consolidating them into a single generic file). And then parsing the .config file for the board specific pieces; like the device tree files, and the kernel target (zimage vs image).

? This .config approach we don't like. Instead, we think it is more appropriate to add support for wildcards to genimage itself (and send that change upstream to pengutronix as well). That way, you can add "*.dtb" to genimage.cfg instead of the current board-specific names.

genimage sort of already has this feature for directories. It's a shame we cant use that feature here, since the pi's bootloader uses device trees in the root of the partition. It would have been nice to have a dtb folder.

Quoted 4 lines

? This approach can then be reused for other boards as well, like the freescale boards on which you probably based this approach. Back in the day that approach of a post-image script that autodiscovers things looked like the right thing to do, but it is actually somewhat complicated and confusing.

I wasn't aware the freescale configs did something similar. That's pretty interesting.

Quoted 7 lines

? If you want to do something like this, I really think it's more appropriate to make a custom genimage.cfg and config.txt that includes everything you want. Note that if you make a custom genimage.cfg, you also don't need to use the raspberrypi post-image script. Instead, use support/scripts/genimage.sh as the post-image script.

Quoted 7 lines

? For the zImage vs. image, you could use "*mage" but I actually think it's more appropriate to keep separate genimage.cfg files for them.

Quoted 2 lines

- Changing the kernel in the config.txt file,
?? Allowing me to boot uboot.bin.

? Cfr. above.

I was really hoping I'd be able to get away with not having to maintain a separate set of files outside of buildroot that basically just replicate functionality already inside of it.
But I guess what I could do is setup my CI such that it watches the buildroot genimage.cfg files and alerts me if any incompatible changes happen.

Quoted 7 lines

? In fact, I don't really like the way the post-image script is updating the config.txt. I think it makes much more sense to have a different config.txt for each board instead of SEDing it. There are two options to handle this: either copy the board-specific config.txt in the post-image script, or (more generically) extend support/scripts/genimage.cfg with options that point to directories/files that have to be copied to IMAGES_DIR before running genimage.

Quoted 3 lines

I enjoy the sed approach. It means buildroot is able to take advantage of upstream changes to the config.txt file, and we're not made to maintain a hoard of copies with minor changes.

Only, config.txt doesn't come from upstream; it comes from
package/rpi-firmware/config.txt and it says "we recommend you to change it to fit your needs".

Okay, it goes on saying to override it in a post-build script, but that's
because there is no other way to put a file into genimage.cfg.

Regards,
Arnout

Quoted 34 lines
Quoted 11 lines
Quoted 2 lines

- Specifying a different rootfs file,
?? Since i would like to use btrfs instead of ext4.

? This one certainly is better done in a custom genimage.cfg.

Quoted 3 lines

- An option to skip creating the full sdimg.
?? As I'm using btrfs, in some cases I only need the vfat boot blob ?? from genimage.

? Again, make a custom genimage.cfg.

very well.

I have a script that configures buildroot as I want it, from defconfigs and fragments. I'll also make it spit out a genimage file.
It'll be easy to do there since that script has access to the devicetree/kernel variables from the defconfig anyway.

Quoted 8 lines
Quoted 4 lines

I'm using a conbination of grep and eval to pull specific values out of the .config file and get them into the script. That might not be best practice.

? I personally prefer to use 'make printvars VARS=...' because you can also extract make-derived variables that way (e.g. LINUX_IMAGE_NAME to get the zImage/image). But either way is fine.

I think I'll use that from now on. I find the eval approach confusing to look at. :)

kind regards, rob.

#12 lore raw

cover board/raspberrypi: post-image customisations.

Quoted 12 lines · Arnout Vandecappelle
Quoted 12 lines
Quoted 11 lines
Quoted 8 lines

Hi all.

I wanted to do use u-boot and mainline kernel sources with my raspies but in trying to do so, found that doing it required a lot of changes to the genimage cfg files.

? Note that the intention is actually that when you change the configuration of
your target, you also change the genimage.cfg file.

Quoted 8 lines
Quoted 2 lines

This is something that I found pretty confusing. It seems illogical to have to set the same options in two distinct places.

True, but this patch series doesn't really change that, does it? E.g. for the
zImage/image kernel, you still have to select both the correct BR2_LINUX_KERNEL_xxIMAGE option and pass --kernel= (rather than updating config.txt).

No. Not for the kernel. I could have changed that, but the script already does some level of faffing with the "kernel=" option. And I decided it would be better to not change the script's behaviour for that option, in case anyone were depending on that particular behaviour.

I was referring to the device trees. Which are first defined in the .config, and then have to be redefined in each genimage.cfg.

Quoted 12 lines
Quoted 11 lines
Quoted 7 lines

? In fact, I don't really like the way the post-image script is updating the
config.txt. I think it makes much more sense to have a different config.txt for each board instead of SEDing it. There are two options to handle this: either copy the board-specific config.txt in the post-image script, or (more generically) extend support/scripts/genimage.cfg with options that point to directories/files that have to be copied to IMAGES_DIR before running genimage.

I enjoy the sed approach. It means buildroot is able to take advantage of upstream changes to the config.txt file, and we're not made to maintain a hoard of copies with minor changes.

Quoted 7 lines

Only, config.txt doesn't come from upstream; it comes from
package/rpi-firmware/config.txt and it says "we recommend you to change it to fit your needs".

Okay, it goes on saying to override it in a post-build script, but that's
because there is no other way to put a file into genimage.cfg.

The package/rpi-firmware/config.txt file is downloaded from the raspberrypi github. While its true that the file won't change without someone updating the commit in the respective .mk file, its not a file that buildroot maintains or authored. It is being pulled from upstream.

If you really wanted to keep separate versions of config.txt around for each board, genimage does support renaming files as it copies them into the image. You could feasibly add a line such as this to each cfg file;

     file config.txt { image = "board/raspberrypi/config_raspberrypi0w.txt" }
Quoted 4 lines

Regards,
Arnout

kind regards, rob.

#13 lore raw

cover board/raspberrypi: post-image customisations.

Robert, All,

On 2019-02-11 11:17 +0000, Robert Heywood spake thusly:

Quoted 11 lines · Arnout Vandecappelle
Quoted 7 lines

Only, config.txt doesn't come from upstream; it comes from
package/rpi-firmware/config.txt and it says "we recommend you to change it to fit your needs".

Okay, it goes on saying to override it in a post-build script, but that's
because there is no other way to put a file into genimage.cfg.

The package/rpi-firmware/config.txt file is downloaded from the raspberrypi github. While its true that the file won't change without someone updating the commit in the respective .mk file,

Absolutely not. The config.txt file *is* bundled in Buildroot.

Quoted 2 lines

its not a file that buildroot
maintains or authored. It is being pulled from upstream.

Yes it is, just do: "git log package/rpi-firmware/config.txt" and you'll see that it is a file we have had since the inception of the rpi-firmware package in Buildroot.

We may have used the upstream one as inspirtion, though.

Quoted 5 lines

If you really wanted to keep separate versions of config.txt around for each board, genimage does support renaming files as it copies them into the image.
You could feasibly add a line such as this to each cfg file;

    file config.txt { image = "board/raspberrypi/config_raspberrypi0w.txt" }

Actually, I think this is a very good idea. But that is just my position, others may disagree...

Again, you have to recognise that the defconfig files we have in Buildroot are just basic configurations and setups, that are there just to help one bootstrap a local build for a custom project/hobby/...

Again, my position is that, if one's project/hobby/... needs a custom linux/uboot/firmware/etc... config file, then one should handle it locally, using the files in Buildroot as inspiration.

Regards,
Yann E. MORIN.

Signature · 6 lines
.-----------------.--------------------.------------------.--------------------.
|  Yann E. MORIN  | Real-Time Embedded | /"\ ASCII RIBBON | Erics' conspiracy: |
| +33 662 376 056 | Software  Designer | \ / CAMPAIGN     |  ___               |
| +33 561 099 427 `------------.-------:  X  AGAINST      |  \e/  There is no  |
| http://ymorin.is-a-geek.org/ | _/*\_ | / \ HTML MAIL    |   v   conspiracy.  |
'------------------------------^-------^------------------^--------------------'