Skip to contentSkip to conversation

imx: add i.MX8MM support

PATCH New Peng Fan 3 participants 39 messages Jan 28, 2019 – Jan 30, 2019 Page 3 of 3

Subsystems (9)
lore
Share & tools
lore
author reviewer
#37 lore raw

PATCH 20/20 imx: add i.MX8MM EVK board support

In reply to Lukasz Majewski
Quoted 86 lines

-----Original Message-----
From: Lukasz Majewski [mailto:lukma at denx.de]
Sent: 2019年1月30日 16:38
To: Peng Fan <[email protected]>
Cc: sbabic at denx.de; Fabio Estevam <[email protected]>; dl-uboot-imx <[email protected]>; u-boot at lists.denx.de
Subject: Re: [U-Boot] [PATCH 20/20] imx: add i.MX8MM EVK board support

Quoted 65 lines · On Wed, 30 Jan 2019 07:07:10 +0000 Peng Fan <[email protected]> wrote:
Quoted 65 lines

-----Original Message-----
From: Lukasz Majewski [mailto:lukma at denx.de]
Sent: 2019年1月30日 14:54
To: Peng Fan <[email protected]>
Cc: sbabic at denx.de; Fabio Estevam <[email protected]>; dl-uboot-imx <[email protected]>; u-boot at lists.denx.de
Subject: Re: [U-Boot] [PATCH 20/20] imx: add i.MX8MM EVK board support

Hi Peng,

Quoted 34 lines
Quoted 34 lines

-----Original Message-----
From: Lukasz Majewski [mailto:lukma at denx.de]
Sent: 2019年1月30日 7:19
To: Peng Fan <[email protected]>
Cc: sbabic at denx.de; Fabio Estevam <[email protected]>; dl-uboot-imx <[email protected]>; u-boot at lists.denx.de
Subject: Re: [U-Boot] [PATCH 20/20] imx: add i.MX8MM EVK board support

Hi Peng,

Quoted 22 lines

Add i.MX8MM EVK board support.

Add board and SoC dts
Add ddr training code
support SD/MMC/GPIO/PINCTRL/UART

U-Boot SPL 2019.01-00148-g1179cffe66 (Jan 28 2019 - 17:37:34 +0800) Normal Boot
Trying to boot from MMC1

U-Boot 2019.01-00148-g1179cffe66 (Jan 28 2019 - 17:37:34 +0800)

CPU:   Freescale i.MX8MMQ rev1.0 at 1200 MHz
Reset cause: POR
Model: NXP i.MX8MM EVK board
DRAM:  2 GiB
MMC:   FSL_SDHC: 1, FSL_SDHC: 2
In:    serial
Out:   serial
Err:   serial

DM

Quoted 4 lines
Quoted 2 lines

You set/adjust latter in the code the fec network driver. Why it is not found?

I dropped network support, could add it in V2.

From the patch it seems like the ETH is fully supported, at lease from the source code point of view.

Quoted 11 lines
Quoted 3 lines

Could you also share the output of "dm tree" command?

Sure.

Quoted 3 lines

I suppose/guess that this board shall support as much as possible of the DT/DM conversions?

Ok.

Quoted 7 lines
Quoted 5 lines

And I would like to emphasize the need of DDR training code (as a functions, not pair of offset and value).

Are you able to provide such code in the next version of the patch?

There is already common code under drivers/ddr/imx8m

Quoted 8 lines

Yes. Indeed there code is there.

Quoted 2 lines

For the array in board file, It need ddr tool change, out of my knowledge.

If the code is there - why not use it for this board? In that way we would kill two birds with one stone - the code would be tested on "blessed" NXP's development board.

It is already used. The lpddr4_timing.c in board file is to provide configuration and the code in drivers/ddr/imx8m will use that to configure DDRC and DDR PHY.

Thanks,
Peng.

Quoted 3,958 lines
Quoted 17 lines

Thanks,
Peng.

Quoted 12 lines
Quoted 12 lines

Regards,
Peng.

Quoted 7 lines
Quoted 7 lines

Hit any key to stop autoboot: 2

---
 arch/arm/dts/fsl-imx8mm-evk.dts            |  203 +++
 arch/arm/dts/fsl-imx8mm.dtsi               |  586

++++++++

Quoted 199 lines
Quoted 199 lines
Quoted 199 lines
Quoted 199 lines
Quoted 199 lines
 arch/arm/mach-imx/imx8m/Kconfig            |    7 +
 board/freescale/imx8mm_evk/Kconfig         |   12 +
 board/freescale/imx8mm_evk/MAINTAINERS     |    6 +
 board/freescale/imx8mm_evk/Makefile        |   12 +
 board/freescale/imx8mm_evk/imx8mm_evk.c    |  144 ++
 board/freescale/imx8mm_evk/lpddr4_timing.c | 1980
++++++++++++++++++++++++++++
board/freescale/imx8mm_evk/spl.c           |  187 +++
configs/imx8mm_evk_defconfig               |   41 +
include/configs/imx8mm_evk.h               |  221 ++++ 11

files changed, 3399 insertions(+) create mode 100644 arch/arm/dts/fsl-imx8mm-evk.dts create mode 100644 arch/arm/dts/fsl-imx8mm.dtsi create mode 100644 board/freescale/imx8mm_evk/Kconfig create mode 100644 board/freescale/imx8mm_evk/MAINTAINERS create mode 100644 board/freescale/imx8mm_evk/Makefile create mode 100644 board/freescale/imx8mm_evk/imx8mm_evk.c create mode 100644 board/freescale/imx8mm_evk/lpddr4_timing.c create mode 100644 board/freescale/imx8mm_evk/spl.c create mode 100644 configs/imx8mm_evk_defconfig create mode 100644 include/configs/imx8mm_evk.h

(quoted diff) +0 -0

b/arch/arm/dts/fsl-imx8mm-evk.dts new file mode 100644 index 0000000000..df409eca47

arch/arm/dts/fsl-imx8mm-evk.dts new file +41 -0
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+
+/dts-v1/;
+
+#include "fsl-imx8mm.dtsi"
+
+/ {
+	model = "NXP i.MX8MM EVK board";
+	compatible = "fsl,imx8mm-evk", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_usdhc2_vmmc: regulator-usdhc2 {
+			compatible = "regulator-fixed";
+			regulator-name = "VSD_3V3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+			off-on-delay = <20000>;
+			enable-active-high;
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	imx8mm-evk {
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+

MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+
MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+
MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+
MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+
MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+
MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+
MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+
MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+
MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+
MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+
MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+
MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+
MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+
MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+
MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_gpio_led: gpioledgrp {
+			fsl,pins = <
+

MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <
+

MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
+
MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc2_gpio: usdhc2grpgpio {
+			fsl,pins = <
+

MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x1c4
+
MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+

MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+
MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+			fsl,pins = <
+

MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+
MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+			fsl,pins = <
+

MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+
MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc3: usdhc3grp {
+			fsl,pins = <
+

MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
+
MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
+
MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
+
MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
+
MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
+
MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
+
MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

+
MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
+
MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
+
MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
+
MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE

	0x190
Quoted 19 lines
Quoted 19 lines
Quoted 19 lines
Quoted 19 lines
Quoted 19 lines
arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+			fsl,pins = <
+

MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
+
MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
+
MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+
MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+
MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+
MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+
MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

+
MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+
MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+
MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+
MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE

	0x194
Quoted 249 lines
Quoted 249 lines
Quoted 249 lines
Quoted 249 lines
Quoted 249 lines
arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+			fsl,pins = <
+

MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
+
MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
+
MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
+
MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
+
MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
+
MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
+
MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
+
MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
+
MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
+
MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
+
MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_wdog: wdoggrp {
+			fsl,pins = <
+

MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6

arch/arm/dts/fsl-imx8mm-evk.dts new file +13 -0
+			>;
+		};
+	};
+};
+
+&uart2 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz",

"state_200mhz";

arch/arm/dts/fsl-imx8mm-evk.dts new file +1 -0
+	pinctrl-0 = <&pinctrl_usdhc2>,

<&pinctrl_usdhc2_gpio>;

arch/arm/dts/fsl-imx8mm-evk.dts new file +1 -0
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>,

<&pinctrl_usdhc2_gpio>;

arch/arm/dts/fsl-imx8mm-evk.dts new file +1 -0
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>,

<&pinctrl_usdhc2_gpio>;

arch/arm/dts/fsl-imx8mm-evk.dts new file +8 -0
+	cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz",

"state_200mhz";

arch/arm/dts/fsl-imx8mm-evk.dts new file +14 -0
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
(quoted diff) +0 -0

b/arch/arm/dts/fsl-imx8mm.dtsi new file mode 100644 index 0000000000..8a808f856d

arch/arm/dts/fsl-imx8mm.dtsi new file +142 -0
@@ -0,0 +1,586 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2017-2019 NXP
+ */
+
+#include <dt-bindings/clock/imx8mm-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/pins-imx8mm.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	compatible = "fsl,imx8mm";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		spi0 = &ecspi1;
+		spi1 = &ecspi2;
+		spi2 = &ecspi3;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		mmc2 = &usdhc3;
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		A53_0: cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			next-level-cache = <&A53_L2>;
+		};
+
+		A53_1: cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			enable-method = "psci";
+			next-level-cache = <&A53_L2>;
+		};
+
+		A53_2: cpu at 2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x2>;
+			enable-method = "psci";
+			next-level-cache = <&A53_L2>;
+		};
+
+		A53_3: cpu at 3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x3>;
+			enable-method = "psci";
+			next-level-cache = <&A53_L2>;
+		};
+
+		A53_L2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	memory at 40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		osc_32k: clock at 0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "osc_32k";
+		};
+
+		osc_24m: clock at 1 {
+			compatible = "fixed-clock";
+			reg = <1>;
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+			clock-output-names = "osc_24m";
+		};
+
+		clk_ext1: clock at 2 {
+			compatible = "fixed-clock";
+			reg = <3>;
+			#clock-cells = <0>;
+			clock-frequency = <133000000>;
+			clock-output-names = "clk_ext1";
+		};
+
+		clk_ext2: clock at 3 {
+			compatible = "fixed-clock";
+			reg = <4>;
+			#clock-cells = <0>;
+			clock-frequency = <133000000>;
+			clock-output-names = "clk_ext2";
+		};
+
+		clk_ext3: clock at 4 {
+			compatible = "fixed-clock";
+			reg = <5>;
+			#clock-cells = <0>;
+			clock-frequency = <133000000>;
+			clock-output-names = "clk_ext3";
+		};
+
+		clk_ext4: clock at 5 {
+			compatible = "fixed-clock";
+			reg = <6>;
+			#clock-cells = <0>;
+			clock-frequency= <133000000>;
+			clock-output-names = "clk_ext4";
+		};
+	};
+
+	gic: interrupt-controller at 38800000 {
+		compatible = "arm,gic-v3";
+		reg = <0x0 0x38800000 0 0x10000>, /* GIC

Dist */

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+		      <0x0 0x38880000 0 0xC0000>; /* GICR

(RD_base + SGI_base) */

arch/arm/dts/fsl-imx8mm.dtsi new file +14 -0
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7
+			(GIC_CPU_MASK_SIMPLE(6) |

IRQ_TYPE_LEVEL_HIGH)>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+		interrupt-affinity = <&A53_0>, <&A53_1>,

<&A53_2>, <&A53_3>;

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+		interrupts = <GIC_PPI 13

(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Physical Secure */

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+			     <GIC_PPI 14

(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Physical Non-Secure */

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+			     <GIC_PPI 11

(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Virtual

*/

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+			     <GIC_PPI 10

(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>; /*

Hypervisor

Quoted 630 lines
Quoted 630 lines
Quoted 630 lines
Quoted 630 lines
Quoted 594 lines

*/

arch/arm/dts/fsl-imx8mm.dtsi new file +12 -0
+		clock-frequency = <8000000>;
+		arm,no-tick-in-suspend;
+	};
+
+	soc at 0 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		aips1: bus at 30000000 {
+			compatible = "fsl,aips-bus",

"simple-bus";

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+			#address-cells = <2>;
+			#size-cells = <2>;
+			reg = <0x0 0x30000000 0x0 0x400000>;
+			ranges;
+
+			gpio1: gpio at 30200000 {
+				compatible =

"fsl,imx8mm-gpio", "fsl,imx35-gpio";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30200000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 64

IRQ_TYPE_LEVEL_HIGH>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					     <GIC_SPI 65

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio2: gpio at 30210000 {
+				compatible =

"fsl,imx8mm-gpio", "fsl,imx35-gpio";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30210000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 66

IRQ_TYPE_LEVEL_HIGH>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					     <GIC_SPI 67

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio3: gpio at 30220000 {
+				compatible =

"fsl,imx8mm-gpio", "fsl,imx35-gpio";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30220000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 68

IRQ_TYPE_LEVEL_HIGH>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					     <GIC_SPI 69

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio4: gpio at 30230000 {
+				compatible =

"fsl,imx8mm-gpio", "fsl,imx35-gpio";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30230000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 70

IRQ_TYPE_LEVEL_HIGH>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					     <GIC_SPI 71

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio5: gpio at 30240000 {
+				compatible =

"fsl,imx8mm-gpio", "fsl,imx35-gpio";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30240000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 72

IRQ_TYPE_LEVEL_HIGH>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					     <GIC_SPI 73

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +9 -0
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			wdog1: wdog at 30280000 {
+				compatible = "fsl,imx21-wdt";
+				reg = <0 0x30280000 0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 78

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_WDOG1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				status = "disabled";
+			};
+
+			wdog2: wdog at 30290000 {
+				compatible = "fsl,imx21-wdt";
+				reg = <0 0x30290000 0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 79

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_WDOG2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				status = "disabled";
+			};
+
+			wdog3: wdog at 302a0000 {
+				compatible = "fsl,imx21-wdt";
+				reg = <0 0x302a0000 0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 10

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_WDOG3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				status = "disabled";
+			};
+
+			sdma2: dma-controller at 302c0000 {
+				compatible =

"fsl,imx8mq-sdma", "fsl,imx7d-sdma";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x302c0000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 103

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_SDMA2_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_SDMA2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +3 -0
+				clock-names = "ipg", "ahb";
+				#dma-cells = <3>;
+				fsl,sdma-ram-script-name =

"imx/sdma/sdma-imx7d.bin";

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				fsl,ratio-1-1;
+				status = "okay";
+			};
+
+			sdma3: dma-controller at 302b0000 {
+				compatible =

"fsl,imx8mq-sdma", "fsl,imx7d-sdma";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x302b0000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 34

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_SDMA3_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				 <&clk

IMX8MM_CLK_SDMA3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +3 -0
+				clock-names = "ipg", "ahb";
+				#dma-cells = <3>;
+				fsl,sdma-ram-script-name =

"imx/sdma/sdma-imx7d.bin";

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				fsl,ratio-1-1;
+				status = "okay";
+			};
+
+			iomuxc: pinctrl at 30330000 {
+				compatible =

"fsl,imx8mm-iomuxc";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30330000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+			};
+
+			gpr: iomuxc-gpr at 30340000 {
+				compatible =

"fsl,imx8mm-iomuxc-gpr", "syscon";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30340000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+			};
+
+			ocotp: ocotp-ctrl at 30350000 {
+				compatible =

"fsl,imx8mq-ocotp", "fsl,imx7d-ocotp", "syscon";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0 0x30350000 0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_OCOTP_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				/* For nvmem subnodes */
+				#address-cells = <1>;
+				#size-cells = <1>;
+			};
+
+			anatop: anatop at 30360000 {
+				compatible =

"fsl,imx8mm-anatop", "syscon", "simple-bus";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30360000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+			};
+
+			snvs: snvs at 30370000 {
+				compatible =

"fsl,sec-v4.0-mon","syscon", "simple-mfd";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30370000 0x0

0x10000>; +

arch/arm/dts/fsl-imx8mm.dtsi new file +2 -0
+				snvs_rtc: snvs-rtc-lp{
+					compatible =

"fsl,sec-v4.0-mon-rtc-lp";

arch/arm/dts/fsl-imx8mm.dtsi new file +3 -0
+					regmap =<&snvs>;
+					offset = <0x34>;
+					interrupts = <GIC_SPI

19 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+						     <GIC_SPI

20 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+				};
+
+				snvs_pwrkey: snvs-powerkey {
+					compatible =

"fsl,sec-v4.0-pwrkey";

arch/arm/dts/fsl-imx8mm.dtsi new file +2 -0
+					regmap = <&snvs>;
+					interrupts =

<GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					linux,keycode =

<KEY_POWER>;

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+					wakeup-source;
+				};
+			};
+
+			clk: clock-controller at 30380000 {
+				compatible =

"fsl,imx8mm-ccm";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30380000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +2 -0
+				#clock-cells = <1>;
+				clocks = <&osc_32k>,

<&osc_24m>, <&clk_ext1>, <&clk_ext2>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk_ext3>,

<&clk_ext4>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "osc_32k",

"osc_24m", "clk_ext1", "clk_ext2",

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					      "clk_ext3",

"clk_ext4";

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+			};
+
+			src: src at 30390000 {
+				compatible =

"fsl,imx8mm-src", "syscon";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30390000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 89

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				#reset-cells = <1>;
+			};
+
+			gpc: gpc at 303a0000 {
+				compatible =

"fsl,imx8mm-gpc", "syscon";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x303a0000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +2 -0
+				interrupt-controller;
+				interrupts = <GIC_SPI 87

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				#interrupt-cells = <3>;
+			};
+		};
+
+		aips2: bus at 30400000 {
+			compatible = "fsl,aips-bus",

"simple-bus";

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+			#address-cells = <2>;
+			#size-cells = <2>;
+			reg = <0x0 0x30400000 0x0 0x400000>;
+			ranges;
+
+			pwm1: pwm at 30660000 {
+				compatible =

"fsl,imx8mm-pwm", "fsl,imx27-pwm";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30660000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 81

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_PWM1_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					<&clk

IMX8MM_CLK_PWM1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				clock-names = "ipg", "per";
+				#pwm-cells = <2>;
+				status = "disabled";
+			};
+
+			pwm2: pwm at 30670000 {
+				compatible =

"fsl,imx8mm-pwm", "fsl,imx27-pwm";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30670000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 82

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_PWM2_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_PWM2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				clock-names = "ipg", "per";
+				#pwm-cells = <2>;
+				status = "disabled";
+			};
+
+			pwm3: pwm at 30680000 {
+				compatible =

"fsl,imx8mm-pwm", "fsl,imx27-pwm";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30680000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 83

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_PWM3_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_PWM3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				clock-names = "ipg", "per";
+				#pwm-cells = <2>;
+				status = "disabled";
+			};
+
+			pwm4: pwm at 30690000 {
+				compatible =

"fsl,imx8mm-pwm", "fsl,imx27-pwm";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30690000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 84

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_PWM4_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_PWM4_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				clock-names = "ipg", "per";
+				#pwm-cells = <2>;
+				status = "disabled";
+			};
+		};
+
+		aips3: bus at 30800000 {
+			compatible = "fsl,aips-bus",

"simple-bus";

arch/arm/dts/fsl-imx8mm.dtsi new file +9 -0
+			#address-cells = <2>;
+			#size-cells = <2>;
+			reg = <0x0 0x30800000 0x0 0x400000>;
+			ranges;
+
+			ecspi1: ecspi at 30820000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-ecspi", "fsl,imx51-ecspi";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30820000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 31

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_ECSPI1_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_ECSPI1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			ecspi2: ecspi at 30830000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-ecspi", "fsl,imx51-ecspi";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30830000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 32

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_ECSPI2_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_ECSPI2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			ecspi3: ecspi at 30840000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-ecspi", "fsl,imx51-ecspi";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30840000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 33

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_ECSPI3_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_ECSPI3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			uart1: serial at 30860000 {
+				compatible =

"fsl,imx8mm-uart",
+
"fsl,imx6q-uart", "fsl,imx21-uart";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30860000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 26

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_UART1_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_UART1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			uart3: serial at 30880000 {
+				compatible =

"fsl,imx8mm-uart",
+
"fsl,imx6q-uart", "fsl,imx21-uart";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30880000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 28

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_UART3_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_UART3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			uart2: serial at 30890000 {
+				compatible =

"fsl,imx8mm-uart",
+
"fsl,imx6q-uart", "fsl,imx21-uart";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30890000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 27

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_UART2_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_UART2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			i2c1: i2c at 30a20000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-i2c", "fsl,imx21-i2c";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30a20000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 35

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_I2C1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				status = "disabled";
+			};
+
+			i2c2: i2c at 30a30000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-i2c", "fsl,imx21-i2c";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30a30000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 36

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_I2C2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				status = "disabled";
+			};
+
+			i2c3: i2c at 30a40000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-i2c", "fsl,imx21-i2c";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30a40000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 37

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_I2C3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				status = "disabled";
+			};
+
+			i2c4: i2c at 30a50000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-i2c", "fsl,imx21-i2c";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30a50000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 38

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_I2C4_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				status = "disabled";
+			};
+
+			uart4: serial at 30a60000 {
+				compatible =

"fsl,imx8mq-uart",
+
"fsl,imx6q-uart", "fsl,imx21-uart";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30a60000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 29

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_UART4_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_UART4_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			usdhc1: mmc at 30b40000 {
+				compatible =

"fsl,imx8mq-usdhc", "fsl,imx7d-usdhc";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30b40000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 22

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_DUMMY>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_NAND_USDHC_BUS>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_USDHC1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg", "ahb",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				assigned-clocks = <&clk

IMX8MM_CLK_USDHC1>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				assigned-clock-rates =

<400000000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step= <2>;
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc2: mmc at 30b50000 {
+				compatible =

"fsl,imx8mq-usdhc", "fsl,imx7d-usdhc";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30b50000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 23

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_DUMMY>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_NAND_USDHC_BUS>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_USDHC2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg", "ahb",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step= <2>;
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc3: mmc at 30b60000 {
+				compatible =

"fsl,imx8mq-usdhc", "fsl,imx7d-usdhc";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30b60000 0x0

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI 24

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk

IMX8MM_CLK_DUMMY>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_NAND_USDHC_BUS>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk

IMX8MM_CLK_USDHC3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg", "ahb",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				assigned-clocks = <&clk

IMX8MM_CLK_USDHC3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				assigned-clock-rates =

<400000000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step= <2>;
+				bus-width = <4>;
+				status = "disabled";
+			};
+		};
+	};
+};
(quoted diff) +0 -0
Quoted 2 lines

b/arch/arm/mach-imx/imx8m/Kconfig index
35c978e863..f520075875

100644

arch/arm/mach-imx/imx8m/Kconfig config TARGET_IMX8MQ_EVK · line 31

Quoted 11 lines
arch/arm/mach-imx/imx8m/Kconfig +5 -0
@@ -24,8 +24,15 @@ config TARGET_IMX8MQ_EVK
 	select IMX8MQ
 	select IMX8M_LPDDR4
 
+config TARGET_IMX8MM_EVK
+	bool "imx8mm LPDDR4 EVK board"
+	select IMX8MM
+	select SUPPORT_SPL
+	select IMX8M_LPDDR4

Here you shall put the select DM_{UART,USDHC, etc}

Quoted 19 lines
arch/arm/mach-imx/imx8m/Kconfig +2 -0
+
 endchoice
 
 source "board/freescale/imx8mq_evk/Kconfig"
+source "board/freescale/imx8mm_evk/Kconfig"
 
 endif
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/Kconfig new file mode 100644 index 0000000000..299691a619

board/freescale/imx8mm_evk/Kconfig new file +6 -0
@@ -0,0 +1,12 @@
+if TARGET_IMX8MM_EVK
+
+config SYS_BOARD
+	default "imx8mm_evk"
+
+config SYS_VENDOR
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
board/freescale/imx8mm_evk/Kconfig new file +6 -0
+	default "freescale"
+
+config SYS_CONFIG_NAME
+	default "imx8mm_evk"
+
+endif
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/MAINTAINERS new file mode

100644

Quoted 22 lines
Quoted 22 lines
Quoted 22 lines
Quoted 22 lines
Quoted 22 lines

index 0000000000..b031bb0674

board/freescale/imx8mm_evk/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@
+i.MX8MM EVK BOARD
+M:	Peng Fan <[email protected]>
+S:	Maintained
+F:	board/freescale/imx8mm_evk/
+F:	include/configs/imx8mm_evk.h
+F:	configs/imx8mm_evk_defconfig
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/Makefile new file mode 100644 index 0000000000..1db7b62caf

board/freescale/imx8mm_evk/Makefile new file +6 -0
@@ -0,0 +1,12 @@
+#
+# Copyright 2018 NXP
+#
+# SPDX-License-Identifier:      GPL-2.0+
+#
+
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
board/freescale/imx8mm_evk/Makefile new file +6 -0
+obj-y += imx8mm_evk.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing.o
+endif
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/imx8mm_evk.c new file mode

100644

Quoted 2,422 lines
Quoted 2,422 lines
Quoted 2,422 lines
Quoted 2,422 lines
Quoted 32 lines

index 0000000000..a681aca04d

board/freescale/imx8mm_evk/imx8mm_evk.c new file +27 -0
@@ -0,0 +1,144 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm-generic/gpio.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <asm/arch/imx8mm_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <asm/arch/clock.h>
+#include <spl.h>
+#include <asm/mach-imx/dma.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_FSEL1)
+#define WDOG_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_ODE |

PAD_CTL_PUE | PAD_CTL_PE) +

board/freescale/imx8mm_evk/imx8mm_evk.c

Quoted 2 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +2 -0
+static iomux_v3_cfg_t const uart_pads[] = {
+	IMX8MM_PAD_UART2_RXD_UART2_RX |

MUX_PAD_CTRL(UART_PAD_CTRL),

board/freescale/imx8mm_evk/imx8mm_evk.c

Quoted 1 line
board/freescale/imx8mm_evk/imx8mm_evk.c new file +1 -0
+	IMX8MM_PAD_UART2_TXD_UART2_TX |

MUX_PAD_CTRL(UART_PAD_CTRL),

Quoted 34 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +4 -0
+};
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	IMX8MM_PAD_GPIO1_IO02_WDOG1_WDOG_B  |

MUX_PAD_CTRL(WDOG_PAD_CTRL), +};

board/freescale/imx8mm_evk/imx8mm_evk.c new file +4 -0
+
+int board_early_init_f(void)
+{
+	struct wdog_regs *wdog = (struct wdog_regs

*)WDOG1_BASE_ADDR; +

board/freescale/imx8mm_evk/imx8mm_evk.c new file +1 -0
+	imx_iomux_v3_setup_multiple_pads(wdog_pads,

ARRAY_SIZE(wdog_pads)); +

board/freescale/imx8mm_evk/imx8mm_evk.c new file +3 -0
+	set_wdog_reset(wdog);
+
+	imx_iomux_v3_setup_multiple_pads(uart_pads,

ARRAY_SIZE(uart_pads)); +

board/freescale/imx8mm_evk/imx8mm_evk.c new file +14 -0
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_POSTCLK_INIT
+int board_postclk_init(void)
+{
+	/* TODO */
+	return 0;
+}
+#endif
+
+int dram_init(void)
+{
+	/* rom_pointer[1] contains the size of TEE occupies

*/

board/freescale/imx8mm_evk/imx8mm_evk.c new file +2 -0
+	if (rom_pointer[1])
+		gd->ram_size = PHYS_SDRAM_SIZE -

rom_pointer[1];

board/freescale/imx8mm_evk/imx8mm_evk.c line 71

Quoted 8 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +8 -0
+	else
+		gd->ram_size = PHYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, bd_t *bd)
	^^^ - fdt_board_setup ?

board/freescale/imx8mm_evk/imx8mm_evk.c

Quoted 9 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +9 -0
+{
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+#define FEC_RST_PAD IMX_GPIO_NR(4, 22)
+static iomux_v3_cfg_t const fec1_rst_pads[] = {
+	IMX8MM_PAD_SAI2_RXC_GPIO4_IO22 |

MUX_PAD_CTRL(NO_PAD_CTRL),

This shall be done with fsl_fec.c DM driver - there is support for adding reset pin (to dts).

board/freescale/imx8mm_evk/imx8mm_evk.c line 92

Quoted 12 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +6 -0
+};
+
+static void setup_iomux_fec(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec1_rst_pads,
+

ARRAY_SIZE(fec1_rst_pads)); +

board/freescale/imx8mm_evk/imx8mm_evk.c new file +5 -0
+	gpio_request(FEC_RST_PAD, "fec1_rst");
+	gpio_direction_output(FEC_RST_PAD, 0);
+	udelay(500);
+	gpio_direction_output(FEC_RST_PAD, 1);
+}

This shall be replaced with DM/DTS of the fsl_fec.c driver. Please also note that there are (at least on imx6q) some timing issues when we move the code to DM/DTS (some delay is needed).

Quoted 21 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +5 -0
+
+static int setup_fec(void)
+{
+	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+		= (struct iomuxc_gpr_base_regs

*)IOMUXC_GPR_BASE_ADDR; +

board/freescale/imx8mm_evk/imx8mm_evk.c new file +3 -0
+	setup_iomux_fec();
+
+	/* Use 125M anatop REF_CLK1 for ENET1, not from

external */

board/freescale/imx8mm_evk/imx8mm_evk.c new file +2 -0
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+

IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_SHIFT, 0);

board/freescale/imx8mm_evk/imx8mm_evk.c new file +6 -0
+	return set_clk_enet(ENET_125MHZ);
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/* enable rgmii rxc skew and phy mode select to RGMII

copper */

board/freescale/imx8mm_evk/imx8mm_evk.c new file +1 -0
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);

board/freescale/imx8mm_evk/imx8mm_evk.c line 120

Quoted 10 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +10 -0
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+	return 0;

Which PHY do you use? E.g. KSZ... support passing those values via DTS.

Quoted 30 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +24 -0
+}
+#endif
+
+int board_init(void)
+{
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+	return 0;
+}
+
+int board_mmc_get_env_dev(int devno)
+{
+	return devno - 1;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	env_set("board_name", "EVK");
+	env_set("board_rev", "iMX8MM");
+#endif
+	return 0;
+}
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/lpddr4_timing.c new file mode 100644 index 0000000000..4bade5bf74

board/freescale/imx8mm_evk/lpddr4_timing.c line 3

Quoted 3 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +3 -0
@@ -0,0 +1,1980 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP

Author is missing.

Quoted 306 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +306 -0
+ */
+
+#include <linux/kernel.h>
+#include <common.h>
+#include <asm/arch/ddr.h>
+#include <asm/arch/lpddr4_define.h>
+
+struct dram_cfg_param lpddr4_ddrc_cfg[] = {
+	/* Start to config, default 3200mbps */
+	{ DDRC_DBG1(0),	0x00000001 },
+	{ DDRC_PWRCTL(0), 0x00000001 },
+	{ DDRC_MSTR(0),	0xa1080020 },
+	{ DDRC_RFSHTMG(0), 0x005b00d2 },
+	{ DDRC_INIT0(0), 0xC003061B },
+	{ DDRC_INIT1(0), 0x009D0000 },
+	{ DDRC_INIT3(0), 0x00D4002D },
+	{ DDRC_INIT4(0), (LPDDR4_MR3 << 16) | 0x0000 },
+	{ DDRC_INIT6(0), 0x0066004a },
+	{ DDRC_INIT7(0), 0x0006004a },
+
+	{ DDRC_DRAMTMG0(0), 0x1A201B22 },
+	{ DDRC_DRAMTMG1(0), 0x00060633 },
+	{ DDRC_DRAMTMG3(0), 0x00C0C000 },
+	{ DDRC_DRAMTMG4(0), 0x0F04080F },
+	{ DDRC_DRAMTMG5(0), 0x02040C0C },
+	{ DDRC_DRAMTMG6(0), 0x01010007 },
+	{ DDRC_DRAMTMG7(0), 0x00000401 },
+	{ DDRC_DRAMTMG12(0), 0x00020600 },
+	{ DDRC_DRAMTMG13(0), 0x0C100002 },
+	{ DDRC_DRAMTMG14(0), 0x000000E6 },
+	{ DDRC_DRAMTMG17(0), 0x00A00050 },
+
+	{ DDRC_ZQCTL0(0), 0x03200018 },
+	{ DDRC_ZQCTL1(0), 0x028061A8 },
+	{ DDRC_ZQCTL2(0), 0x00000000 },
+
+	{ DDRC_DFITMG0(0), 0x0497820A },
+	{ DDRC_DFITMG2(0), 0x0000170A },
+	{ DDRC_DRAMTMG2(0), 0x070E171a },
+	{ DDRC_DBICTL(0), 0x00000001 },
+
+	{ DDRC_DFITMG1(0), 0x00080303 },
+	{ DDRC_DFIUPD0(0), 0xE0400018 },
+	{ DDRC_DFIUPD1(0), 0x00DF00E4 },
+	{ DDRC_DFIUPD2(0), 0x80000000 },
+	{ DDRC_DFIMISC(0), 0x00000011 },
+
+	{ DDRC_DFIPHYMSTR(0), 0x00000000 },
+	{ DDRC_RANKCTL(0), 0x00000c99 },
+
+	/* address mapping */
+	{ DDRC_ADDRMAP0(0), 0x0000001f },
+	{ DDRC_ADDRMAP1(0), 0x00080808 },
+	{ DDRC_ADDRMAP2(0), 0x00000000 },
+	{ DDRC_ADDRMAP3(0), 0x00000000 },
+	{ DDRC_ADDRMAP4(0), 0x00001f1f },
+	{ DDRC_ADDRMAP5(0), 0x07070707 },
+	{ DDRC_ADDRMAP6(0), 0x07070707 },
+	{ DDRC_ADDRMAP7(0), 0x00000f0f },
+
+	/* performance setting */
+	{ DDRC_SCHED(0), 0x29001701 },
+	{ DDRC_SCHED1(0), 0x0000002c },
+	{ DDRC_PERFHPR1(0), 0x04000030 },
+	{ DDRC_PERFLPR1(0), 0x900093e7 },
+	{ DDRC_PERFWR1(0), 0x20005574 },
+	{ DDRC_PCCFG(0), 0x00000111 },
+	{ DDRC_PCFGW_0(0), 0x000072ff },
+	{ DDRC_PCFGQOS0_0(0), 0x02100e07 },
+	{ DDRC_PCFGQOS1_0(0), 0x00620096 },
+	{ DDRC_PCFGWQOS0_0(0), 0x01100e07 },
+	{ DDRC_PCFGWQOS1_0(0), 0x00c8012c },
+
+	/* frequency P1&P2 */
+	/* Frequency 1: 400mbps */
+	{ DDRC_FREQ1_DRAMTMG0(0), 0x0d0b010c },
+	{ DDRC_FREQ1_DRAMTMG1(0), 0x00030410 },
+	{ DDRC_FREQ1_DRAMTMG2(0), 0x0203090c },
+	{ DDRC_FREQ1_DRAMTMG3(0), 0x00505006 },
+	{ DDRC_FREQ1_DRAMTMG4(0), 0x05040305 },
+	{ DDRC_FREQ1_DRAMTMG5(0), 0x0d0e0504 },
+	{ DDRC_FREQ1_DRAMTMG6(0), 0x0a060004 },
+	{ DDRC_FREQ1_DRAMTMG7(0), 0x0000090e },
+	{ DDRC_FREQ1_DRAMTMG14(0), 0x00000032 },
+	{ DDRC_FREQ1_DRAMTMG15(0), 0x00000000 },
+	{ DDRC_FREQ1_DRAMTMG17(0), 0x0036001b },
+	{ DDRC_FREQ1_DERATEINT(0), 0x7e9fbeb1 },
+	{ DDRC_FREQ1_DFITMG0(0), 0x03818200 },
+	{ DDRC_FREQ1_DFITMG2(0), 0x00000000 },
+	{ DDRC_FREQ1_RFSHTMG(0), 0x000C001c },
+	{ DDRC_FREQ1_INIT3(0), 0x00840000 },
+	{ DDRC_FREQ1_INIT4(0), 0x00310000 },
+	{ DDRC_FREQ1_INIT6(0), 0x0066004a },
+	{ DDRC_FREQ1_INIT7(0), 0x0006004a },
+
+	/* Frequency 2: 100mbps */
+	{ DDRC_FREQ2_DRAMTMG0(0), 0x0d0b010c },
+	{ DDRC_FREQ2_DRAMTMG1(0), 0x00030410 },
+	{ DDRC_FREQ2_DRAMTMG2(0), 0x0203090c },
+	{ DDRC_FREQ2_DRAMTMG3(0), 0x00505006 },
+	{ DDRC_FREQ2_DRAMTMG4(0), 0x05040305 },
+	{ DDRC_FREQ2_DRAMTMG5(0), 0x0d0e0504 },
+	{ DDRC_FREQ2_DRAMTMG6(0), 0x0a060004 },
+	{ DDRC_FREQ2_DRAMTMG7(0), 0x0000090e },
+	{ DDRC_FREQ2_DRAMTMG14(0), 0x00000032 },
+	{ DDRC_FREQ2_DRAMTMG17(0), 0x0036001b },
+	{ DDRC_FREQ2_DERATEINT(0), 0x7e9fbeb1 },
+	{ DDRC_FREQ2_DFITMG0(0), 0x03818200 },
+	{ DDRC_FREQ2_DFITMG2(0), 0x00000000 },
+	{ DDRC_FREQ2_RFSHTMG(0), 0x0003800c },
+	{ DDRC_FREQ2_RFSHTMG(0), 0x00030007 },
+	{ DDRC_FREQ2_INIT3(0), 0x00840000 },
+	{ DDRC_FREQ2_INIT4(0), 0x00310008 },
+	{ DDRC_FREQ2_INIT4(0), (LPDDR4_MR3 << 16) | 0x0000 },
+	{ DDRC_FREQ2_INIT6(0), 0x0066004a },
+	{ DDRC_FREQ2_INIT7(0), 0x0006004a },
+
+	/* boot start point */
+	{ DDRC_MSTR2(0), 0x2 }, //DDRC_MSTR2
+};
+
+/* PHY Initialize Configuration */
+struct dram_cfg_param lpddr4_ddrphy_cfg[] = {
+	{ 0x1005f, 0x1ff },
+	{ 0x1015f, 0x1ff },
+	{ 0x1105f, 0x1ff },
+	{ 0x1115f, 0x1ff },
+	{ 0x1205f, 0x1ff },
+	{ 0x1215f, 0x1ff },
+	{ 0x1305f, 0x1ff },
+	{ 0x1315f, 0x1ff },
+
+	{ 0x11005f, 0x1ff },
+	{ 0x11015f, 0x1ff },
+	{ 0x11105f, 0x1ff },
+	{ 0x11115f, 0x1ff },
+	{ 0x11205f, 0x1ff },
+	{ 0x11215f, 0x1ff },
+	{ 0x11305f, 0x1ff },
+	{ 0x11315f, 0x1ff },
+
+	{ 0x21005f, 0x1ff },
+	{ 0x21015f, 0x1ff },
+	{ 0x21105f, 0x1ff },
+	{ 0x21115f, 0x1ff },
+	{ 0x21205f, 0x1ff },
+	{ 0x21215f, 0x1ff },
+	{ 0x21305f, 0x1ff },
+	{ 0x21315f, 0x1ff },
+
+	{ 0x55, 0x1ff },
+	{ 0x1055, 0x1ff },
+	{ 0x2055, 0x1ff },
+	{ 0x3055, 0x1ff },
+	{ 0x4055, 0x1ff },
+	{ 0x5055, 0x1ff },
+	{ 0x6055, 0x1ff },
+	{ 0x7055, 0x1ff },
+	{ 0x8055, 0x1ff },
+	{ 0x9055, 0x1ff },
+
+	{ 0x200c5, 0x19 },
+	{ 0x1200c5, 0x7 },
+	{ 0x2200c5, 0x7 },
+
+	{ 0x2002e, 0x2 },
+	{ 0x12002e, 0x2 },
+	{ 0x22002e, 0x2 },
+
+	{ 0x90204, 0x0 },
+	{ 0x190204, 0x0 },
+	{ 0x290204, 0x0 },
+
+	{ 0x20024, 0xab },
+	{ 0x2003a, 0x0 },
+
+	{ 0x120024, 0xab },
+	{ 0x2003a, 0x0 },
+
+	{ 0x220024, 0xab },
+	{ 0x2003a, 0x0 },
+
+	{ 0x20056, 0x3 },
+	{ 0x120056, 0xa },
+	{ 0x220056, 0xa },
+
+	{ 0x1004d, 0xe00 },
+	{ 0x1014d, 0xe00 },
+	{ 0x1104d, 0xe00 },
+	{ 0x1114d, 0xe00 },
+	{ 0x1204d, 0xe00 },
+	{ 0x1214d, 0xe00 },
+	{ 0x1304d, 0xe00 },
+	{ 0x1314d, 0xe00 },
+
+	{ 0x11004d, 0xe00 },
+	{ 0x11014d, 0xe00 },
+	{ 0x11104d, 0xe00 },
+	{ 0x11114d, 0xe00 },
+	{ 0x11204d, 0xe00 },
+	{ 0x11214d, 0xe00 },
+	{ 0x11304d, 0xe00 },
+	{ 0x11314d, 0xe00 },
+
+	{ 0x21004d, 0xe00 },
+	{ 0x21014d, 0xe00 },
+	{ 0x21104d, 0xe00 },
+	{ 0x21114d, 0xe00 },
+	{ 0x21204d, 0xe00 },
+	{ 0x21214d, 0xe00 },
+	{ 0x21304d, 0xe00 },
+	{ 0x21314d, 0xe00 },
+
+	{ 0x10049, 0xfbe },
+	{ 0x10149, 0xfbe },
+	{ 0x11049, 0xfbe },
+	{ 0x11149, 0xfbe },
+	{ 0x12049, 0xfbe },
+	{ 0x12149, 0xfbe },
+	{ 0x13049, 0xfbe },
+	{ 0x13149, 0xfbe },
+
+	{ 0x110049, 0xfbe },
+	{ 0x110149, 0xfbe },
+	{ 0x111049, 0xfbe },
+	{ 0x111149, 0xfbe },
+	{ 0x112049, 0xfbe },
+	{ 0x112149, 0xfbe },
+	{ 0x113049, 0xfbe },
+	{ 0x113149, 0xfbe },
+
+	{ 0x210049, 0xfbe },
+	{ 0x210149, 0xfbe },
+	{ 0x211049, 0xfbe },
+	{ 0x211149, 0xfbe },
+	{ 0x212049, 0xfbe },
+	{ 0x212149, 0xfbe },
+	{ 0x213049, 0xfbe },
+	{ 0x213149, 0xfbe },
+
+	{ 0x43, 0x63 },
+	{ 0x1043, 0x63 },
+	{ 0x2043, 0x63 },
+	{ 0x3043, 0x63 },
+	{ 0x4043, 0x63 },
+	{ 0x5043, 0x63 },
+	{ 0x6043, 0x63 },
+	{ 0x7043, 0x63 },
+	{ 0x8043, 0x63 },
+	{ 0x9043, 0x63 },
+
+	{ 0x20018, 0x3 },
+	{ 0x20075, 0x4 },
+	{ 0x20050, 0x0 },
+	{ 0x20008, 0x2ee },
+	{ 0x120008, 0x64 },
+	{ 0x220008, 0x19 },
+	{ 0x20088, 0x9 },
+
+	{ 0x200b2, 0x1d4 },
+	{ 0x10043, 0x5a1 },
+	{ 0x10143, 0x5a1 },
+	{ 0x11043, 0x5a1 },
+	{ 0x11143, 0x5a1 },
+	{ 0x12043, 0x5a1 },
+	{ 0x12143, 0x5a1 },
+	{ 0x13043, 0x5a1 },
+	{ 0x13143, 0x5a1 },
+
+	{ 0x1200b2, 0xdc },
+	{ 0x110043, 0x5a1 },
+	{ 0x110143, 0x5a1 },
+	{ 0x111043, 0x5a1 },
+	{ 0x111143, 0x5a1 },
+	{ 0x112043, 0x5a1 },
+	{ 0x112143, 0x5a1 },
+	{ 0x113043, 0x5a1 },
+	{ 0x113143, 0x5a1 },
+
+	{ 0x2200b2, 0xdc },
+	{ 0x210043, 0x5a1 },
+	{ 0x210143, 0x5a1 },
+	{ 0x211043, 0x5a1 },
+	{ 0x211143, 0x5a1 },
+	{ 0x212043, 0x5a1 },
+	{ 0x212143, 0x5a1 },
+	{ 0x213043, 0x5a1 },
+	{ 0x213143, 0x5a1 },
+
+	{ 0x200fa, 0x1 },
+	{ 0x1200fa, 0x1 },
+	{ 0x2200fa, 0x1 },
+
+	{ 0x20019, 0x1 },
+	{ 0x120019, 0x1 },
+	{ 0x220019, 0x1 },
+
+	{ 0x200f0, 0x660 },
+	{ 0x200f1, 0x0 },
+	{ 0x200f2, 0x4444 },
+	{ 0x200f3, 0x8888 },
+	{ 0x200f4, 0x5665 },
+	{ 0x200f5, 0x0 },
+	{ 0x200f6, 0x0 },
+	{ 0x200f7, 0xf000 },
+

board/freescale/imx8mm_evk/lpddr4_timing.c line 319

Quoted 10 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +10 -0
+	{ 0x20025, 0x0 },
+	{ 0x2002d, LPDDR4_PHY_DMIPinPresent },
+	{ 0x12002d, LPDDR4_PHY_DMIPinPresent },
+	{ 0x22002d, LPDDR4_PHY_DMIPinPresent },
+	{ 0x200c7, 0x21 },
+	{ 0x200ca, 0x24 },
+	{ 0x1200c7, 0x21 },
+	{ 0x1200ca, 0x24 },
+	{ 0x2200c7, 0x21 },
+	{ 0x2200ca, 0x24 },

Why do you add tuple - offset and value? Shouldn't we have the DDR training functions here?

It is possible to train IMX6Q and Vybrid's DDR3 (as fair as I know). Would it be also possible to add the DDR4 training code for IMX8?

Quoted 714 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +714 -0
+};
+
+/* ddr phy trained csr */
+struct dram_cfg_param lpddr4_ddrphy_trained_csr[] = {
+	{ 0x200b2, 0x0 },
+	{ 0x1200b2, 0x0 },
+	{ 0x2200b2, 0x0 },
+	{ 0x200cb, 0x0 },
+	{ 0x10043, 0x0 },
+	{ 0x110043, 0x0 },
+	{ 0x210043, 0x0 },
+	{ 0x10143, 0x0 },
+	{ 0x110143, 0x0 },
+	{ 0x210143, 0x0 },
+	{ 0x11043, 0x0 },
+	{ 0x111043, 0x0 },
+	{ 0x211043, 0x0 },
+	{ 0x11143, 0x0 },
+	{ 0x111143, 0x0 },
+	{ 0x211143, 0x0 },
+	{ 0x12043, 0x0 },
+	{ 0x112043, 0x0 },
+	{ 0x212043, 0x0 },
+	{ 0x12143, 0x0 },
+	{ 0x112143, 0x0 },
+	{ 0x212143, 0x0 },
+	{ 0x13043, 0x0 },
+	{ 0x113043, 0x0 },
+	{ 0x213043, 0x0 },
+	{ 0x13143, 0x0 },
+	{ 0x113143, 0x0 },
+	{ 0x213143, 0x0 },
+	{ 0x80, 0x0 },
+	{ 0x100080, 0x0 },
+	{ 0x200080, 0x0 },
+	{ 0x1080, 0x0 },
+	{ 0x101080, 0x0 },
+	{ 0x201080, 0x0 },
+	{ 0x2080, 0x0 },
+	{ 0x102080, 0x0 },
+	{ 0x202080, 0x0 },
+	{ 0x3080, 0x0 },
+	{ 0x103080, 0x0 },
+	{ 0x203080, 0x0 },
+	{ 0x4080, 0x0 },
+	{ 0x104080, 0x0 },
+	{ 0x204080, 0x0 },
+	{ 0x5080, 0x0 },
+	{ 0x105080, 0x0 },
+	{ 0x205080, 0x0 },
+	{ 0x6080, 0x0 },
+	{ 0x106080, 0x0 },
+	{ 0x206080, 0x0 },
+	{ 0x7080, 0x0 },
+	{ 0x107080, 0x0 },
+	{ 0x207080, 0x0 },
+	{ 0x8080, 0x0 },
+	{ 0x108080, 0x0 },
+	{ 0x208080, 0x0 },
+	{ 0x9080, 0x0 },
+	{ 0x109080, 0x0 },
+	{ 0x209080, 0x0 },
+	{ 0x10080, 0x0 },
+	{ 0x110080, 0x0 },
+	{ 0x210080, 0x0 },
+	{ 0x10180, 0x0 },
+	{ 0x110180, 0x0 },
+	{ 0x210180, 0x0 },
+	{ 0x11080, 0x0 },
+	{ 0x111080, 0x0 },
+	{ 0x211080, 0x0 },
+	{ 0x11180, 0x0 },
+	{ 0x111180, 0x0 },
+	{ 0x211180, 0x0 },
+	{ 0x12080, 0x0 },
+	{ 0x112080, 0x0 },
+	{ 0x212080, 0x0 },
+	{ 0x12180, 0x0 },
+	{ 0x112180, 0x0 },
+	{ 0x212180, 0x0 },
+	{ 0x13080, 0x0 },
+	{ 0x113080, 0x0 },
+	{ 0x213080, 0x0 },
+	{ 0x13180, 0x0 },
+	{ 0x113180, 0x0 },
+	{ 0x213180, 0x0 },
+	{ 0x10081, 0x0 },
+	{ 0x110081, 0x0 },
+	{ 0x210081, 0x0 },
+	{ 0x10181, 0x0 },
+	{ 0x110181, 0x0 },
+	{ 0x210181, 0x0 },
+	{ 0x11081, 0x0 },
+	{ 0x111081, 0x0 },
+	{ 0x211081, 0x0 },
+	{ 0x11181, 0x0 },
+	{ 0x111181, 0x0 },
+	{ 0x211181, 0x0 },
+	{ 0x12081, 0x0 },
+	{ 0x112081, 0x0 },
+	{ 0x212081, 0x0 },
+	{ 0x12181, 0x0 },
+	{ 0x112181, 0x0 },
+	{ 0x212181, 0x0 },
+	{ 0x13081, 0x0 },
+	{ 0x113081, 0x0 },
+	{ 0x213081, 0x0 },
+	{ 0x13181, 0x0 },
+	{ 0x113181, 0x0 },
+	{ 0x213181, 0x0 },
+	{ 0x100d0, 0x0 },
+	{ 0x1100d0, 0x0 },
+	{ 0x2100d0, 0x0 },
+	{ 0x101d0, 0x0 },
+	{ 0x1101d0, 0x0 },
+	{ 0x2101d0, 0x0 },
+	{ 0x110d0, 0x0 },
+	{ 0x1110d0, 0x0 },
+	{ 0x2110d0, 0x0 },
+	{ 0x111d0, 0x0 },
+	{ 0x1111d0, 0x0 },
+	{ 0x2111d0, 0x0 },
+	{ 0x120d0, 0x0 },
+	{ 0x1120d0, 0x0 },
+	{ 0x2120d0, 0x0 },
+	{ 0x121d0, 0x0 },
+	{ 0x1121d0, 0x0 },
+	{ 0x2121d0, 0x0 },
+	{ 0x130d0, 0x0 },
+	{ 0x1130d0, 0x0 },
+	{ 0x2130d0, 0x0 },
+	{ 0x131d0, 0x0 },
+	{ 0x1131d0, 0x0 },
+	{ 0x2131d0, 0x0 },
+	{ 0x100d1, 0x0 },
+	{ 0x1100d1, 0x0 },
+	{ 0x2100d1, 0x0 },
+	{ 0x101d1, 0x0 },
+	{ 0x1101d1, 0x0 },
+	{ 0x2101d1, 0x0 },
+	{ 0x110d1, 0x0 },
+	{ 0x1110d1, 0x0 },
+	{ 0x2110d1, 0x0 },
+	{ 0x111d1, 0x0 },
+	{ 0x1111d1, 0x0 },
+	{ 0x2111d1, 0x0 },
+	{ 0x120d1, 0x0 },
+	{ 0x1120d1, 0x0 },
+	{ 0x2120d1, 0x0 },
+	{ 0x121d1, 0x0 },
+	{ 0x1121d1, 0x0 },
+	{ 0x2121d1, 0x0 },
+	{ 0x130d1, 0x0 },
+	{ 0x1130d1, 0x0 },
+	{ 0x2130d1, 0x0 },
+	{ 0x131d1, 0x0 },
+	{ 0x1131d1, 0x0 },
+	{ 0x2131d1, 0x0 },
+	{ 0x10068, 0x0 },
+	{ 0x10168, 0x0 },
+	{ 0x10268, 0x0 },
+	{ 0x10368, 0x0 },
+	{ 0x10468, 0x0 },
+	{ 0x10568, 0x0 },
+	{ 0x10668, 0x0 },
+	{ 0x10768, 0x0 },
+	{ 0x10868, 0x0 },
+	{ 0x11068, 0x0 },
+	{ 0x11168, 0x0 },
+	{ 0x11268, 0x0 },
+	{ 0x11368, 0x0 },
+	{ 0x11468, 0x0 },
+	{ 0x11568, 0x0 },
+	{ 0x11668, 0x0 },
+	{ 0x11768, 0x0 },
+	{ 0x11868, 0x0 },
+	{ 0x12068, 0x0 },
+	{ 0x12168, 0x0 },
+	{ 0x12268, 0x0 },
+	{ 0x12368, 0x0 },
+	{ 0x12468, 0x0 },
+	{ 0x12568, 0x0 },
+	{ 0x12668, 0x0 },
+	{ 0x12768, 0x0 },
+	{ 0x12868, 0x0 },
+	{ 0x13068, 0x0 },
+	{ 0x13168, 0x0 },
+	{ 0x13268, 0x0 },
+	{ 0x13368, 0x0 },
+	{ 0x13468, 0x0 },
+	{ 0x13568, 0x0 },
+	{ 0x13668, 0x0 },
+	{ 0x13768, 0x0 },
+	{ 0x13868, 0x0 },
+	{ 0x10069, 0x0 },
+	{ 0x10169, 0x0 },
+	{ 0x10269, 0x0 },
+	{ 0x10369, 0x0 },
+	{ 0x10469, 0x0 },
+	{ 0x10569, 0x0 },
+	{ 0x10669, 0x0 },
+	{ 0x10769, 0x0 },
+	{ 0x10869, 0x0 },
+	{ 0x11069, 0x0 },
+	{ 0x11169, 0x0 },
+	{ 0x11269, 0x0 },
+	{ 0x11369, 0x0 },
+	{ 0x11469, 0x0 },
+	{ 0x11569, 0x0 },
+	{ 0x11669, 0x0 },
+	{ 0x11769, 0x0 },
+	{ 0x11869, 0x0 },
+	{ 0x12069, 0x0 },
+	{ 0x12169, 0x0 },
+	{ 0x12269, 0x0 },
+	{ 0x12369, 0x0 },
+	{ 0x12469, 0x0 },
+	{ 0x12569, 0x0 },
+	{ 0x12669, 0x0 },
+	{ 0x12769, 0x0 },
+	{ 0x12869, 0x0 },
+	{ 0x13069, 0x0 },
+	{ 0x13169, 0x0 },
+	{ 0x13269, 0x0 },
+	{ 0x13369, 0x0 },
+	{ 0x13469, 0x0 },
+	{ 0x13569, 0x0 },
+	{ 0x13669, 0x0 },
+	{ 0x13769, 0x0 },
+	{ 0x13869, 0x0 },
+	{ 0x1008c, 0x0 },
+	{ 0x11008c, 0x0 },
+	{ 0x21008c, 0x0 },
+	{ 0x1018c, 0x0 },
+	{ 0x11018c, 0x0 },
+	{ 0x21018c, 0x0 },
+	{ 0x1108c, 0x0 },
+	{ 0x11108c, 0x0 },
+	{ 0x21108c, 0x0 },
+	{ 0x1118c, 0x0 },
+	{ 0x11118c, 0x0 },
+	{ 0x21118c, 0x0 },
+	{ 0x1208c, 0x0 },
+	{ 0x11208c, 0x0 },
+	{ 0x21208c, 0x0 },
+	{ 0x1218c, 0x0 },
+	{ 0x11218c, 0x0 },
+	{ 0x21218c, 0x0 },
+	{ 0x1308c, 0x0 },
+	{ 0x11308c, 0x0 },
+	{ 0x21308c, 0x0 },
+	{ 0x1318c, 0x0 },
+	{ 0x11318c, 0x0 },
+	{ 0x21318c, 0x0 },
+	{ 0x1008d, 0x0 },
+	{ 0x11008d, 0x0 },
+	{ 0x21008d, 0x0 },
+	{ 0x1018d, 0x0 },
+	{ 0x11018d, 0x0 },
+	{ 0x21018d, 0x0 },
+	{ 0x1108d, 0x0 },
+	{ 0x11108d, 0x0 },
+	{ 0x21108d, 0x0 },
+	{ 0x1118d, 0x0 },
+	{ 0x11118d, 0x0 },
+	{ 0x21118d, 0x0 },
+	{ 0x1208d, 0x0 },
+	{ 0x11208d, 0x0 },
+	{ 0x21208d, 0x0 },
+	{ 0x1218d, 0x0 },
+	{ 0x11218d, 0x0 },
+	{ 0x21218d, 0x0 },
+	{ 0x1308d, 0x0 },
+	{ 0x11308d, 0x0 },
+	{ 0x21308d, 0x0 },
+	{ 0x1318d, 0x0 },
+	{ 0x11318d, 0x0 },
+	{ 0x21318d, 0x0 },
+	{ 0x100c0, 0x0 },
+	{ 0x1100c0, 0x0 },
+	{ 0x2100c0, 0x0 },
+	{ 0x101c0, 0x0 },
+	{ 0x1101c0, 0x0 },
+	{ 0x2101c0, 0x0 },
+	{ 0x102c0, 0x0 },
+	{ 0x1102c0, 0x0 },
+	{ 0x2102c0, 0x0 },
+	{ 0x103c0, 0x0 },
+	{ 0x1103c0, 0x0 },
+	{ 0x2103c0, 0x0 },
+	{ 0x104c0, 0x0 },
+	{ 0x1104c0, 0x0 },
+	{ 0x2104c0, 0x0 },
+	{ 0x105c0, 0x0 },
+	{ 0x1105c0, 0x0 },
+	{ 0x2105c0, 0x0 },
+	{ 0x106c0, 0x0 },
+	{ 0x1106c0, 0x0 },
+	{ 0x2106c0, 0x0 },
+	{ 0x107c0, 0x0 },
+	{ 0x1107c0, 0x0 },
+	{ 0x2107c0, 0x0 },
+	{ 0x108c0, 0x0 },
+	{ 0x1108c0, 0x0 },
+	{ 0x2108c0, 0x0 },
+	{ 0x110c0, 0x0 },
+	{ 0x1110c0, 0x0 },
+	{ 0x2110c0, 0x0 },
+	{ 0x111c0, 0x0 },
+	{ 0x1111c0, 0x0 },
+	{ 0x2111c0, 0x0 },
+	{ 0x112c0, 0x0 },
+	{ 0x1112c0, 0x0 },
+	{ 0x2112c0, 0x0 },
+	{ 0x113c0, 0x0 },
+	{ 0x1113c0, 0x0 },
+	{ 0x2113c0, 0x0 },
+	{ 0x114c0, 0x0 },
+	{ 0x1114c0, 0x0 },
+	{ 0x2114c0, 0x0 },
+	{ 0x115c0, 0x0 },
+	{ 0x1115c0, 0x0 },
+	{ 0x2115c0, 0x0 },
+	{ 0x116c0, 0x0 },
+	{ 0x1116c0, 0x0 },
+	{ 0x2116c0, 0x0 },
+	{ 0x117c0, 0x0 },
+	{ 0x1117c0, 0x0 },
+	{ 0x2117c0, 0x0 },
+	{ 0x118c0, 0x0 },
+	{ 0x1118c0, 0x0 },
+	{ 0x2118c0, 0x0 },
+	{ 0x120c0, 0x0 },
+	{ 0x1120c0, 0x0 },
+	{ 0x2120c0, 0x0 },
+	{ 0x121c0, 0x0 },
+	{ 0x1121c0, 0x0 },
+	{ 0x2121c0, 0x0 },
+	{ 0x122c0, 0x0 },
+	{ 0x1122c0, 0x0 },
+	{ 0x2122c0, 0x0 },
+	{ 0x123c0, 0x0 },
+	{ 0x1123c0, 0x0 },
+	{ 0x2123c0, 0x0 },
+	{ 0x124c0, 0x0 },
+	{ 0x1124c0, 0x0 },
+	{ 0x2124c0, 0x0 },
+	{ 0x125c0, 0x0 },
+	{ 0x1125c0, 0x0 },
+	{ 0x2125c0, 0x0 },
+	{ 0x126c0, 0x0 },
+	{ 0x1126c0, 0x0 },
+	{ 0x2126c0, 0x0 },
+	{ 0x127c0, 0x0 },
+	{ 0x1127c0, 0x0 },
+	{ 0x2127c0, 0x0 },
+	{ 0x128c0, 0x0 },
+	{ 0x1128c0, 0x0 },
+	{ 0x2128c0, 0x0 },
+	{ 0x130c0, 0x0 },
+	{ 0x1130c0, 0x0 },
+	{ 0x2130c0, 0x0 },
+	{ 0x131c0, 0x0 },
+	{ 0x1131c0, 0x0 },
+	{ 0x2131c0, 0x0 },
+	{ 0x132c0, 0x0 },
+	{ 0x1132c0, 0x0 },
+	{ 0x2132c0, 0x0 },
+	{ 0x133c0, 0x0 },
+	{ 0x1133c0, 0x0 },
+	{ 0x2133c0, 0x0 },
+	{ 0x134c0, 0x0 },
+	{ 0x1134c0, 0x0 },
+	{ 0x2134c0, 0x0 },
+	{ 0x135c0, 0x0 },
+	{ 0x1135c0, 0x0 },
+	{ 0x2135c0, 0x0 },
+	{ 0x136c0, 0x0 },
+	{ 0x1136c0, 0x0 },
+	{ 0x2136c0, 0x0 },
+	{ 0x137c0, 0x0 },
+	{ 0x1137c0, 0x0 },
+	{ 0x2137c0, 0x0 },
+	{ 0x138c0, 0x0 },
+	{ 0x1138c0, 0x0 },
+	{ 0x2138c0, 0x0 },
+	{ 0x100c1, 0x0 },
+	{ 0x1100c1, 0x0 },
+	{ 0x2100c1, 0x0 },
+	{ 0x101c1, 0x0 },
+	{ 0x1101c1, 0x0 },
+	{ 0x2101c1, 0x0 },
+	{ 0x102c1, 0x0 },
+	{ 0x1102c1, 0x0 },
+	{ 0x2102c1, 0x0 },
+	{ 0x103c1, 0x0 },
+	{ 0x1103c1, 0x0 },
+	{ 0x2103c1, 0x0 },
+	{ 0x104c1, 0x0 },
+	{ 0x1104c1, 0x0 },
+	{ 0x2104c1, 0x0 },
+	{ 0x105c1, 0x0 },
+	{ 0x1105c1, 0x0 },
+	{ 0x2105c1, 0x0 },
+	{ 0x106c1, 0x0 },
+	{ 0x1106c1, 0x0 },
+	{ 0x2106c1, 0x0 },
+	{ 0x107c1, 0x0 },
+	{ 0x1107c1, 0x0 },
+	{ 0x2107c1, 0x0 },
+	{ 0x108c1, 0x0 },
+	{ 0x1108c1, 0x0 },
+	{ 0x2108c1, 0x0 },
+	{ 0x110c1, 0x0 },
+	{ 0x1110c1, 0x0 },
+	{ 0x2110c1, 0x0 },
+	{ 0x111c1, 0x0 },
+	{ 0x1111c1, 0x0 },
+	{ 0x2111c1, 0x0 },
+	{ 0x112c1, 0x0 },
+	{ 0x1112c1, 0x0 },
+	{ 0x2112c1, 0x0 },
+	{ 0x113c1, 0x0 },
+	{ 0x1113c1, 0x0 },
+	{ 0x2113c1, 0x0 },
+	{ 0x114c1, 0x0 },
+	{ 0x1114c1, 0x0 },
+	{ 0x2114c1, 0x0 },
+	{ 0x115c1, 0x0 },
+	{ 0x1115c1, 0x0 },
+	{ 0x2115c1, 0x0 },
+	{ 0x116c1, 0x0 },
+	{ 0x1116c1, 0x0 },
+	{ 0x2116c1, 0x0 },
+	{ 0x117c1, 0x0 },
+	{ 0x1117c1, 0x0 },
+	{ 0x2117c1, 0x0 },
+	{ 0x118c1, 0x0 },
+	{ 0x1118c1, 0x0 },
+	{ 0x2118c1, 0x0 },
+	{ 0x120c1, 0x0 },
+	{ 0x1120c1, 0x0 },
+	{ 0x2120c1, 0x0 },
+	{ 0x121c1, 0x0 },
+	{ 0x1121c1, 0x0 },
+	{ 0x2121c1, 0x0 },
+	{ 0x122c1, 0x0 },
+	{ 0x1122c1, 0x0 },
+	{ 0x2122c1, 0x0 },
+	{ 0x123c1, 0x0 },
+	{ 0x1123c1, 0x0 },
+	{ 0x2123c1, 0x0 },
+	{ 0x124c1, 0x0 },
+	{ 0x1124c1, 0x0 },
+	{ 0x2124c1, 0x0 },
+	{ 0x125c1, 0x0 },
+	{ 0x1125c1, 0x0 },
+	{ 0x2125c1, 0x0 },
+	{ 0x126c1, 0x0 },
+	{ 0x1126c1, 0x0 },
+	{ 0x2126c1, 0x0 },
+	{ 0x127c1, 0x0 },
+	{ 0x1127c1, 0x0 },
+	{ 0x2127c1, 0x0 },
+	{ 0x128c1, 0x0 },
+	{ 0x1128c1, 0x0 },
+	{ 0x2128c1, 0x0 },
+	{ 0x130c1, 0x0 },
+	{ 0x1130c1, 0x0 },
+	{ 0x2130c1, 0x0 },
+	{ 0x131c1, 0x0 },
+	{ 0x1131c1, 0x0 },
+	{ 0x2131c1, 0x0 },
+	{ 0x132c1, 0x0 },
+	{ 0x1132c1, 0x0 },
+	{ 0x2132c1, 0x0 },
+	{ 0x133c1, 0x0 },
+	{ 0x1133c1, 0x0 },
+	{ 0x2133c1, 0x0 },
+	{ 0x134c1, 0x0 },
+	{ 0x1134c1, 0x0 },
+	{ 0x2134c1, 0x0 },
+	{ 0x135c1, 0x0 },
+	{ 0x1135c1, 0x0 },
+	{ 0x2135c1, 0x0 },
+	{ 0x136c1, 0x0 },
+	{ 0x1136c1, 0x0 },
+	{ 0x2136c1, 0x0 },
+	{ 0x137c1, 0x0 },
+	{ 0x1137c1, 0x0 },
+	{ 0x2137c1, 0x0 },
+	{ 0x138c1, 0x0 },
+	{ 0x1138c1, 0x0 },
+	{ 0x2138c1, 0x0 },
+	{ 0x10020, 0x0 },
+	{ 0x110020, 0x0 },
+	{ 0x210020, 0x0 },
+	{ 0x11020, 0x0 },
+	{ 0x111020, 0x0 },
+	{ 0x211020, 0x0 },
+	{ 0x12020, 0x0 },
+	{ 0x112020, 0x0 },
+	{ 0x212020, 0x0 },
+	{ 0x13020, 0x0 },
+	{ 0x113020, 0x0 },
+	{ 0x213020, 0x0 },
+	{ 0x20072, 0x0 },
+	{ 0x20073, 0x0 },
+	{ 0x20074, 0x0 },
+	{ 0x100aa, 0x0 },
+	{ 0x110aa, 0x0 },
+	{ 0x120aa, 0x0 },
+	{ 0x130aa, 0x0 },
+	{ 0x20010, 0x0 },
+	{ 0x120010, 0x0 },
+	{ 0x220010, 0x0 },
+	{ 0x20011, 0x0 },
+	{ 0x120011, 0x0 },
+	{ 0x220011, 0x0 },
+	{ 0x100ae, 0x0 },
+	{ 0x1100ae, 0x0 },
+	{ 0x2100ae, 0x0 },
+	{ 0x100af, 0x0 },
+	{ 0x1100af, 0x0 },
+	{ 0x2100af, 0x0 },
+	{ 0x110ae, 0x0 },
+	{ 0x1110ae, 0x0 },
+	{ 0x2110ae, 0x0 },
+	{ 0x110af, 0x0 },
+	{ 0x1110af, 0x0 },
+	{ 0x2110af, 0x0 },
+	{ 0x120ae, 0x0 },
+	{ 0x1120ae, 0x0 },
+	{ 0x2120ae, 0x0 },
+	{ 0x120af, 0x0 },
+	{ 0x1120af, 0x0 },
+	{ 0x2120af, 0x0 },
+	{ 0x130ae, 0x0 },
+	{ 0x1130ae, 0x0 },
+	{ 0x2130ae, 0x0 },
+	{ 0x130af, 0x0 },
+	{ 0x1130af, 0x0 },
+	{ 0x2130af, 0x0 },
+	{ 0x20020, 0x0 },
+	{ 0x120020, 0x0 },
+	{ 0x220020, 0x0 },
+	{ 0x100a0, 0x0 },
+	{ 0x100a1, 0x0 },
+	{ 0x100a2, 0x0 },
+	{ 0x100a3, 0x0 },
+	{ 0x100a4, 0x0 },
+	{ 0x100a5, 0x0 },
+	{ 0x100a6, 0x0 },
+	{ 0x100a7, 0x0 },
+	{ 0x110a0, 0x0 },
+	{ 0x110a1, 0x0 },
+	{ 0x110a2, 0x0 },
+	{ 0x110a3, 0x0 },
+	{ 0x110a4, 0x0 },
+	{ 0x110a5, 0x0 },
+	{ 0x110a6, 0x0 },
+	{ 0x110a7, 0x0 },
+	{ 0x120a0, 0x0 },
+	{ 0x120a1, 0x0 },
+	{ 0x120a2, 0x0 },
+	{ 0x120a3, 0x0 },
+	{ 0x120a4, 0x0 },
+	{ 0x120a5, 0x0 },
+	{ 0x120a6, 0x0 },
+	{ 0x120a7, 0x0 },
+	{ 0x130a0, 0x0 },
+	{ 0x130a1, 0x0 },
+	{ 0x130a2, 0x0 },
+	{ 0x130a3, 0x0 },
+	{ 0x130a4, 0x0 },
+	{ 0x130a5, 0x0 },
+	{ 0x130a6, 0x0 },
+	{ 0x130a7, 0x0 },
+	{ 0x2007c, 0x0 },
+	{ 0x12007c, 0x0 },
+	{ 0x22007c, 0x0 },
+	{ 0x2007d, 0x0 },
+	{ 0x12007d, 0x0 },
+	{ 0x22007d, 0x0 },
+	{ 0x400fd, 0x0 },
+	{ 0x400c0, 0x0 },
+	{ 0x90201, 0x0 },
+	{ 0x190201, 0x0 },
+	{ 0x290201, 0x0 },
+	{ 0x90202, 0x0 },
+	{ 0x190202, 0x0 },
+	{ 0x290202, 0x0 },
+	{ 0x90203, 0x0 },
+	{ 0x190203, 0x0 },
+	{ 0x290203, 0x0 },
+	{ 0x90204, 0x0 },
+	{ 0x190204, 0x0 },
+	{ 0x290204, 0x0 },
+	{ 0x90205, 0x0 },
+	{ 0x190205, 0x0 },
+	{ 0x290205, 0x0 },
+	{ 0x90206, 0x0 },
+	{ 0x190206, 0x0 },
+	{ 0x290206, 0x0 },
+	{ 0x90207, 0x0 },
+	{ 0x190207, 0x0 },
+	{ 0x290207, 0x0 },
+	{ 0x90208, 0x0 },
+	{ 0x190208, 0x0 },
+	{ 0x290208, 0x0 },
+	{ 0x10062, 0x0 },
+	{ 0x10162, 0x0 },
+	{ 0x10262, 0x0 },
+	{ 0x10362, 0x0 },
+	{ 0x10462, 0x0 },
+	{ 0x10562, 0x0 },
+	{ 0x10662, 0x0 },
+	{ 0x10762, 0x0 },
+	{ 0x10862, 0x0 },
+	{ 0x11062, 0x0 },
+	{ 0x11162, 0x0 },
+	{ 0x11262, 0x0 },
+	{ 0x11362, 0x0 },
+	{ 0x11462, 0x0 },
+	{ 0x11562, 0x0 },
+	{ 0x11662, 0x0 },
+	{ 0x11762, 0x0 },
+	{ 0x11862, 0x0 },
+	{ 0x12062, 0x0 },
+	{ 0x12162, 0x0 },
+	{ 0x12262, 0x0 },
+	{ 0x12362, 0x0 },
+	{ 0x12462, 0x0 },
+	{ 0x12562, 0x0 },
+	{ 0x12662, 0x0 },
+	{ 0x12762, 0x0 },
+	{ 0x12862, 0x0 },
+	{ 0x13062, 0x0 },
+	{ 0x13162, 0x0 },
+	{ 0x13262, 0x0 },
+	{ 0x13362, 0x0 },
+	{ 0x13462, 0x0 },
+	{ 0x13562, 0x0 },
+	{ 0x13662, 0x0 },
+	{ 0x13762, 0x0 },
+	{ 0x13862, 0x0 },
+	{ 0x20077, 0x0 },
+	{ 0x10001, 0x0 },
+	{ 0x11001, 0x0 },
+	{ 0x12001, 0x0 },
+	{ 0x13001, 0x0 },
+	{ 0x10040, 0x0 },
+	{ 0x10140, 0x0 },
+	{ 0x10240, 0x0 },
+	{ 0x10340, 0x0 },
+	{ 0x10440, 0x0 },
+	{ 0x10540, 0x0 },
+	{ 0x10640, 0x0 },
+	{ 0x10740, 0x0 },
+	{ 0x10840, 0x0 },
+	{ 0x10030, 0x0 },
+	{ 0x10130, 0x0 },
+	{ 0x10230, 0x0 },
+	{ 0x10330, 0x0 },
+	{ 0x10430, 0x0 },
+	{ 0x10530, 0x0 },
+	{ 0x10630, 0x0 },
+	{ 0x10730, 0x0 },
+	{ 0x10830, 0x0 },
+	{ 0x11040, 0x0 },
+	{ 0x11140, 0x0 },
+	{ 0x11240, 0x0 },
+	{ 0x11340, 0x0 },
+	{ 0x11440, 0x0 },
+	{ 0x11540, 0x0 },
+	{ 0x11640, 0x0 },
+	{ 0x11740, 0x0 },
+	{ 0x11840, 0x0 },
+	{ 0x11030, 0x0 },
+	{ 0x11130, 0x0 },
+	{ 0x11230, 0x0 },
+	{ 0x11330, 0x0 },
+	{ 0x11430, 0x0 },
+	{ 0x11530, 0x0 },
+	{ 0x11630, 0x0 },
+	{ 0x11730, 0x0 },
+	{ 0x11830, 0x0 },
+	{ 0x12040, 0x0 },
+	{ 0x12140, 0x0 },
+	{ 0x12240, 0x0 },
+	{ 0x12340, 0x0 },
+	{ 0x12440, 0x0 },
+	{ 0x12540, 0x0 },
+	{ 0x12640, 0x0 },
+	{ 0x12740, 0x0 },
+	{ 0x12840, 0x0 },
+	{ 0x12030, 0x0 },
+	{ 0x12130, 0x0 },
+	{ 0x12230, 0x0 },
+	{ 0x12330, 0x0 },
+	{ 0x12430, 0x0 },
+	{ 0x12530, 0x0 },
+	{ 0x12630, 0x0 },
+	{ 0x12730, 0x0 },
+	{ 0x12830, 0x0 },
+	{ 0x13040, 0x0 },
+	{ 0x13140, 0x0 },
+	{ 0x13240, 0x0 },
+	{ 0x13340, 0x0 },
+	{ 0x13440, 0x0 },
+	{ 0x13540, 0x0 },
+	{ 0x13640, 0x0 },
+	{ 0x13740, 0x0 },
+	{ 0x13840, 0x0 },

board/freescale/imx8mm_evk/lpddr4_timing.c line 1043

Quoted 10 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +10 -0
+	{ 0x13030, 0x0 },
+	{ 0x13130, 0x0 },
+	{ 0x13230, 0x0 },
+	{ 0x13330, 0x0 },
+	{ 0x13430, 0x0 },
+	{ 0x13530, 0x0 },
+	{ 0x13630, 0x0 },
+	{ 0x13730, 0x0 },
+	{ 0x13830, 0x0 },
+};

The same as above. Please look into imx6q DDR3 training code.

Quoted 886 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +10 -0
+
+/* P0 message block paremeter for training firmware */
+struct dram_cfg_param lpddr4_fsp0_cfg[] = {
+	{ 0xd0000, 0x0 },
+	{ 0x54000, 0x0 },
+	{ 0x54001, 0x0 },
+	{ 0x54002, 0x0 },
+	{ 0x54003, 0xbb8 },
+	{ 0x54004, 0x2 },
+	{ 0x54005, ((LPDDR4_PHY_RON << 8) |

LPDDR4_PHY_RTT) },//PHY Ron/Rtt

board/freescale/imx8mm_evk/lpddr4_timing.c new file +75 -0
+	{ 0x54006, LPDDR4_PHY_VREF_VALUE },
+	{ 0x54007, 0x0 },
+	{ 0x54008, 0x131f },
+	{ 0x54009, 0xc8 },
+	{ 0x5400a, 0x0 },
+	{ 0x5400b, 0x2 },
+	{ 0x5400c, 0x0 },
+	{ 0x5400d, 0x0 },
+	{ 0x5400e, 0x0 },
+	{ 0x5400f, 0x0 },
+	{ 0x54010, 0x0 },
+	{ 0x54011, 0x0 },
+	{ 0x54012, (LPDDR4_CS << 8) | (0x110 & 0xff) },
+	{ 0x54013, 0x0 },
+	{ 0x54014, 0x0 },
+	{ 0x54015, 0x0 },
+	{ 0x54016, 0x0 },
+	{ 0x54017, 0x0 },
+	{ 0x54018, 0x0 },
+	{ 0x54019, 0x2dd4 },
+	{ 0x5401a, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x5401b, 0x4d66 },
+	{ 0x5401c, 0x4d08 },
+	{ 0x5401d, 0x0 },
+	{ 0x5401e, LPDDR4_MR22_RANK0/*0x16*/ },
+	{ 0x5401f, 0x2dd4 },
+	{ 0x54020, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x54021, 0x4d66 },
+	{ 0x54022, 0x4d08 },
+	{ 0x54023, 0x0 },
+	{ 0x54024, LPDDR4_MR22_RANK1/*0x16*/ },
+	{ 0x54025, 0x0 },
+	{ 0x54026, 0x0 },
+	{ 0x54027, 0x0 },
+	{ 0x54028, 0x0 },
+	{ 0x54029, 0x0 },
+	{ 0x5402a, 0x0 },
+	{ 0x5402b, 0x1000 },
+	{ 0x5402c, LPDDR4_CS },
+	{ 0x5402d, 0x0 },
+	{ 0x5402e, 0x0 },
+	{ 0x5402f, 0x0 },
+	{ 0x54030, 0x0 },
+	{ 0x54031, 0x0 },
+	{ 0x54032, 0xd400 },
+	{ 0x54033, (LPDDR4_MR3 << 8) | (0x312d & 0xff) },
+	{ 0x54034, 0x6600 },
+	{ 0x54035, 0x84d },
+	{ 0x54036, 0x4d },
+	{ 0x54037, (LPDDR4_MR22_RANK0 << 8)/*0x1600*/ },
+	{ 0x54038, 0xd400 },
+	{ 0x54039, (LPDDR4_MR3 << 8) | (0x312d & 0xff) },
+	{ 0x5403a, 0x6600 },
+	{ 0x5403b, 0x84d },
+	{ 0x5403c, 0x4d },
+	{ 0x5403d, (LPDDR4_MR22_RANK1 << 8)/*0x1600*/ },
+	{ 0x5403e, 0x0 },
+	{ 0x5403f, 0x0 },
+	{ 0x54040, 0x0 },
+	{ 0x54041, 0x0 },
+	{ 0x54042, 0x0 },
+	{ 0x54043, 0x0 },
+	{ 0x54044, 0x0 },
+	{ 0xd0000, 0x1 },
+};
+
+/* P1 message block paremeter for training firmware */
+struct dram_cfg_param lpddr4_fsp1_cfg[] = {
+	{ 0xd0000, 0x0 },
+	{ 0x54000, 0x0 },
+	{ 0x54001, 0x0 },
+	{ 0x54002, 0x101 },
+	{ 0x54003, 0x190 },
+	{ 0x54004, 0x2 },
+	{ 0x54005, ((LPDDR4_PHY_RON << 8) |

LPDDR4_PHY_RTT) },//PHY Ron/Rtt

board/freescale/imx8mm_evk/lpddr4_timing.c new file +75 -0
+	{ 0x54006, LPDDR4_PHY_VREF_VALUE },
+	{ 0x54007, 0x0 },
+	{ 0x54008, 0x121f },
+	{ 0x54009, 0xc8 },
+	{ 0x5400a, 0x0 },
+	{ 0x5400b, 0x2 },
+	{ 0x5400c, 0x0 },
+	{ 0x5400d, 0x0 },
+	{ 0x5400e, 0x0 },
+	{ 0x5400f, 0x0 },
+	{ 0x54010, 0x0 },
+	{ 0x54011, 0x0 },
+	{ 0x54012, (LPDDR4_CS << 8) | (0x110 & 0xff) },
+	{ 0x54013, 0x0 },
+	{ 0x54014, 0x0 },
+	{ 0x54015, 0x0 },
+	{ 0x54016, 0x0 },
+	{ 0x54017, 0x0 },
+	{ 0x54018, 0x0 },
+	{ 0x54019, 0x84 },
+	{ 0x5401a, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x5401b, 0x4d66 },
+	{ 0x5401c, 0x4d08 },
+	{ 0x5401d, 0x0 },
+	{ 0x5401e, LPDDR4_MR22_RANK0/*0x16*/ },
+	{ 0x5401f, 0x84 },
+	{ 0x54020, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x54021, 0x4d66 },
+	{ 0x54022, 0x4d08 },
+	{ 0x54023, 0x0 },
+	{ 0x54024, LPDDR4_MR22_RANK1/*0x16*/ },
+	{ 0x54025, 0x0 },
+	{ 0x54026, 0x0 },
+	{ 0x54027, 0x0 },
+	{ 0x54028, 0x0 },
+	{ 0x54029, 0x0 },
+	{ 0x5402a, 0x0 },
+	{ 0x5402b, 0x1000 },
+	{ 0x5402c, LPDDR4_CS },
+	{ 0x5402d, 0x0 },
+	{ 0x5402e, 0x0 },
+	{ 0x5402f, 0x0 },
+	{ 0x54030, 0x0 },
+	{ 0x54031, 0x0 },
+	{ 0x54032, 0x8400 },
+	{ 0x54033, (LPDDR4_MR3 << 8) | (0x3100 & 0xff) },
+	{ 0x54034, 0x6600 },
+	{ 0x54035, 0x84d },
+	{ 0x54036, 0x4d },
+	{ 0x54037, (LPDDR4_MR22_RANK0 << 8)/*0x1600*/ },
+	{ 0x54038, 0x8400 },
+	{ 0x54039, (LPDDR4_MR3 << 8) | (0x3100 & 0xff) },
+	{ 0x5403a, 0x6600 },
+	{ 0x5403b, 0x84d },
+	{ 0x5403c, 0x4d },
+	{ 0x5403d, (LPDDR4_MR22_RANK1 << 8)/*0x1600*/ },
+	{ 0x5403e, 0x0 },
+	{ 0x5403f, 0x0 },
+	{ 0x54040, 0x0 },
+	{ 0x54041, 0x0 },
+	{ 0x54042, 0x0 },
+	{ 0x54043, 0x0 },
+	{ 0x54044, 0x0 },
+	{ 0xd0000, 0x1 },
+};
+
+/* P1 message block paremeter for training firmware */
+struct dram_cfg_param lpddr4_fsp2_cfg[] = {
+	{ 0xd0000, 0x0 },
+	{ 0x54000, 0x0 },
+	{ 0x54001, 0x0 },
+	{ 0x54002, 0x102 },
+	{ 0x54003, 0x64 },
+	{ 0x54004, 0x2 },
+	{ 0x54005, ((LPDDR4_PHY_RON << 8) |

LPDDR4_PHY_RTT) },//PHY Ron/Rtt

board/freescale/imx8mm_evk/lpddr4_timing.c new file +75 -0
+	{ 0x54006, LPDDR4_PHY_VREF_VALUE },
+	{ 0x54007, 0x0 },
+	{ 0x54008, 0x121f },
+	{ 0x54009, 0xc8 },
+	{ 0x5400a, 0x0 },
+	{ 0x5400b, 0x2 },
+	{ 0x5400c, 0x0 },
+	{ 0x5400d, 0x0 },
+	{ 0x5400e, 0x0 },
+	{ 0x5400f, 0x0 },
+	{ 0x54010, 0x0 },
+	{ 0x54011, 0x0 },
+	{ 0x54012, (LPDDR4_CS << 8) | (0x110 & 0xff) },
+	{ 0x54013, 0x0 },
+	{ 0x54014, 0x0 },
+	{ 0x54015, 0x0 },
+	{ 0x54016, 0x0 },
+	{ 0x54017, 0x0 },
+	{ 0x54018, 0x0 },
+	{ 0x54019, 0x84 },
+	{ 0x5401a, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x5401b, 0x4d66 },
+	{ 0x5401c, 0x4d08 },
+	{ 0x5401d, 0x0 },
+	{ 0x5401e, LPDDR4_MR22_RANK0/*0x16*/ },
+	{ 0x5401f, 0x84 },
+	{ 0x54020, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x54021, 0x4d66 },
+	{ 0x54022, 0x4d08 },
+	{ 0x54023, 0x0 },
+	{ 0x54024, LPDDR4_MR22_RANK1/*0x16*/ },
+	{ 0x54025, 0x0 },
+	{ 0x54026, 0x0 },
+	{ 0x54027, 0x0 },
+	{ 0x54028, 0x0 },
+	{ 0x54029, 0x0 },
+	{ 0x5402a, 0x0 },
+	{ 0x5402b, 0x1000 },
+	{ 0x5402c, LPDDR4_CS },
+	{ 0x5402d, 0x0 },
+	{ 0x5402e, 0x0 },
+	{ 0x5402f, 0x0 },
+	{ 0x54030, 0x0 },
+	{ 0x54031, 0x0 },
+	{ 0x54032, 0x8400 },
+	{ 0x54033, (LPDDR4_MR3 << 8) | (0x3100 & 0xff) },
+	{ 0x54034, 0x6600 },
+	{ 0x54035, 0x84d },
+	{ 0x54036, 0x4d },
+	{ 0x54037, (LPDDR4_MR22_RANK0 << 8)/*0x1600*/ },
+	{ 0x54038, 0x8400 },
+	{ 0x54039, (LPDDR4_MR3 << 8) | (0x3100 & 0xff) },
+	{ 0x5403a, 0x6600 },
+	{ 0x5403b, 0x84d },
+	{ 0x5403c, 0x4d },
+	{ 0x5403d, (LPDDR4_MR22_RANK1 << 8)/*0x1600*/ },
+	{ 0x5403e, 0x0 },
+	{ 0x5403f, 0x0 },
+	{ 0x54040, 0x0 },
+	{ 0x54041, 0x0 },
+	{ 0x54042, 0x0 },
+	{ 0x54043, 0x0 },
+	{ 0x54044, 0x0 },
+	{ 0xd0000, 0x1 },
+};
+
+/* P0 2D message block paremeter for training firmware */
+struct dram_cfg_param lpddr4_fsp0_2d_cfg[] = {
+	{ 0xd0000, 0x0 },
+	{ 0x54000, 0x0 },
+	{ 0x54001, 0x0 },
+	{ 0x54002, 0x0 },
+	{ 0x54003, 0xbb8 },
+	{ 0x54004, 0x2 },
+	{ 0x54005, ((LPDDR4_PHY_RON << 8) |

LPDDR4_PHY_RTT) },//PHY Ron/Rtt

board/freescale/imx8mm_evk/lpddr4_timing.c new file +647 -0
+	{ 0x54006, LPDDR4_PHY_VREF_VALUE },
+	{ 0x54007, 0x0 },
+	{ 0x54008, 0x61 },
+	{ 0x54009, 0xc8 },
+	{ 0x5400a, 0x0 },
+	{ 0x5400b, 0x2 },
+	{ 0x5400c, 0x0 },
+	{ 0x5400d, 0x0 },
+	{ 0x5400e, 0x0 },
+	{ 0x5400f, 0x100 },
+	{ 0x54010, 0x1f7f },
+	{ 0x54011, 0x0 },
+	{ 0x54012, (LPDDR4_CS << 8) | (0x110 & 0xff) },
+	{ 0x54013, 0x0 },
+	{ 0x54014, 0x0 },
+	{ 0x54015, 0x0 },
+	{ 0x54016, 0x0 },
+	{ 0x54017, 0x0 },
+	{ 0x54018, 0x0 },
+	{ 0x54019, 0x2dd4 },
+	{ 0x5401a, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x5401b, 0x4d66 },
+	{ 0x5401c, 0x4d08 },
+	{ 0x5401d, 0x0 },
+	{ 0x5401e, LPDDR4_MR22_RANK0/*0x16*/ },
+	{ 0x5401f, 0x2dd4 },
+	{ 0x54020, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x54021, 0x4d66 },
+	{ 0x54022, 0x4d08 },
+	{ 0x54023, 0x0 },
+	{ 0x54024, LPDDR4_MR22_RANK1/*0x16*/ },
+	{ 0x54025, 0x0 },
+	{ 0x54026, 0x0 },
+	{ 0x54027, 0x0 },
+	{ 0x54028, 0x0 },
+	{ 0x54029, 0x0 },
+	{ 0x5402a, 0x0 },
+	{ 0x5402b, 0x1000 },
+	{ 0x5402c, LPDDR4_CS },
+	{ 0x5402d, 0x0 },
+	{ 0x5402e, 0x0 },
+	{ 0x5402f, 0x0 },
+	{ 0x54030, 0x0 },
+	{ 0x54031, 0x0 },
+	{ 0x54032, 0xd400 },
+	{ 0x54033, (LPDDR4_MR3 << 8) | (0x312d & 0xff) },
+	{ 0x54034, 0x6600 },
+	{ 0x54035, 0x84d },
+	{ 0x54036, 0x4d },
+	{ 0x54037, (LPDDR4_MR22_RANK0 << 8)/*0x1600*/ },
+	{ 0x54038, 0xd400 },
+	{ 0x54039, (LPDDR4_MR3 << 8) | (0x312d & 0xff) },
+	{ 0x5403a, 0x6600 },
+	{ 0x5403b, 0x84d },
+	{ 0x5403c, 0x4d },
+	{ 0x5403d, (LPDDR4_MR22_RANK1 << 8)/*0x1600*/ },
+	{ 0x5403e, 0x0 },
+	{ 0x5403f, 0x0 },
+	{ 0x54040, 0x0 },
+	{ 0x54041, 0x0 },
+	{ 0x54042, 0x0 },
+	{ 0x54043, 0x0 },
+	{ 0x54044, 0x0 },
+	{ 0xd0000, 0x1 },
+};
+
+/* DRAM PHY init engine image */
+struct dram_cfg_param lpddr4_phy_pie[] = {
+	{ 0xd0000, 0x0 },
+	{ 0x90000, 0x10 },
+	{ 0x90001, 0x400 },
+	{ 0x90002, 0x10e },
+	{ 0x90003, 0x0 },
+	{ 0x90004, 0x0 },
+	{ 0x90005, 0x8 },
+	{ 0x90029, 0xb },
+	{ 0x9002a, 0x480 },
+	{ 0x9002b, 0x109 },
+	{ 0x9002c, 0x8 },
+	{ 0x9002d, 0x448 },
+	{ 0x9002e, 0x139 },
+	{ 0x9002f, 0x8 },
+	{ 0x90030, 0x478 },
+	{ 0x90031, 0x109 },
+	{ 0x90032, 0x0 },
+	{ 0x90033, 0xe8 },
+	{ 0x90034, 0x109 },
+	{ 0x90035, 0x2 },
+	{ 0x90036, 0x10 },
+	{ 0x90037, 0x139 },
+	{ 0x90038, 0xf },
+	{ 0x90039, 0x7c0 },
+	{ 0x9003a, 0x139 },
+	{ 0x9003b, 0x44 },
+	{ 0x9003c, 0x630 },
+	{ 0x9003d, 0x159 },
+	{ 0x9003e, 0x14f },
+	{ 0x9003f, 0x630 },
+	{ 0x90040, 0x159 },
+	{ 0x90041, 0x47 },
+	{ 0x90042, 0x630 },
+	{ 0x90043, 0x149 },
+	{ 0x90044, 0x4f },
+	{ 0x90045, 0x630 },
+	{ 0x90046, 0x179 },
+	{ 0x90047, 0x8 },
+	{ 0x90048, 0xe0 },
+	{ 0x90049, 0x109 },
+	{ 0x9004a, 0x0 },
+	{ 0x9004b, 0x7c8 },
+	{ 0x9004c, 0x109 },
+	{ 0x9004d, 0x0 },
+	{ 0x9004e, 0x1 },
+	{ 0x9004f, 0x8 },
+	{ 0x90050, 0x0 },
+	{ 0x90051, 0x45a },
+	{ 0x90052, 0x9 },
+	{ 0x90053, 0x0 },
+	{ 0x90054, 0x448 },
+	{ 0x90055, 0x109 },
+	{ 0x90056, 0x40 },
+	{ 0x90057, 0x630 },
+	{ 0x90058, 0x179 },
+	{ 0x90059, 0x1 },
+	{ 0x9005a, 0x618 },
+	{ 0x9005b, 0x109 },
+	{ 0x9005c, 0x40c0 },
+	{ 0x9005d, 0x630 },
+	{ 0x9005e, 0x149 },
+	{ 0x9005f, 0x8 },
+	{ 0x90060, 0x4 },
+	{ 0x90061, 0x48 },
+	{ 0x90062, 0x4040 },
+	{ 0x90063, 0x630 },
+	{ 0x90064, 0x149 },
+	{ 0x90065, 0x0 },
+	{ 0x90066, 0x4 },
+	{ 0x90067, 0x48 },
+	{ 0x90068, 0x40 },
+	{ 0x90069, 0x630 },
+	{ 0x9006a, 0x149 },
+	{ 0x9006b, 0x10 },
+	{ 0x9006c, 0x4 },
+	{ 0x9006d, 0x18 },
+	{ 0x9006e, 0x0 },
+	{ 0x9006f, 0x4 },
+	{ 0x90070, 0x78 },
+	{ 0x90071, 0x549 },
+	{ 0x90072, 0x630 },
+	{ 0x90073, 0x159 },
+	{ 0x90074, 0xd49 },
+	{ 0x90075, 0x630 },
+	{ 0x90076, 0x159 },
+	{ 0x90077, 0x94a },
+	{ 0x90078, 0x630 },
+	{ 0x90079, 0x159 },
+	{ 0x9007a, 0x441 },
+	{ 0x9007b, 0x630 },
+	{ 0x9007c, 0x149 },
+	{ 0x9007d, 0x42 },
+	{ 0x9007e, 0x630 },
+	{ 0x9007f, 0x149 },
+	{ 0x90080, 0x1 },
+	{ 0x90081, 0x630 },
+	{ 0x90082, 0x149 },
+	{ 0x90083, 0x0 },
+	{ 0x90084, 0xe0 },
+	{ 0x90085, 0x109 },
+	{ 0x90086, 0xa },
+	{ 0x90087, 0x10 },
+	{ 0x90088, 0x109 },
+	{ 0x90089, 0x9 },
+	{ 0x9008a, 0x3c0 },
+	{ 0x9008b, 0x149 },
+	{ 0x9008c, 0x9 },
+	{ 0x9008d, 0x3c0 },
+	{ 0x9008e, 0x159 },
+	{ 0x9008f, 0x18 },
+	{ 0x90090, 0x10 },
+	{ 0x90091, 0x109 },
+	{ 0x90092, 0x0 },
+	{ 0x90093, 0x3c0 },
+	{ 0x90094, 0x109 },
+	{ 0x90095, 0x18 },
+	{ 0x90096, 0x4 },
+	{ 0x90097, 0x48 },
+	{ 0x90098, 0x18 },
+	{ 0x90099, 0x4 },
+	{ 0x9009a, 0x58 },
+	{ 0x9009b, 0xa },
+	{ 0x9009c, 0x10 },
+	{ 0x9009d, 0x109 },
+	{ 0x9009e, 0x2 },
+	{ 0x9009f, 0x10 },
+	{ 0x900a0, 0x109 },
+	{ 0x900a1, 0x5 },
+	{ 0x900a2, 0x7c0 },
+	{ 0x900a3, 0x109 },
+	{ 0x900a4, 0x10 },
+	{ 0x900a5, 0x10 },
+	{ 0x900a6, 0x109 },
+	{ 0x40000, 0x811 },
+	{ 0x40020, 0x880 },
+	{ 0x40040, 0x0 },
+	{ 0x40060, 0x0 },
+	{ 0x40001, 0x4008 },
+	{ 0x40021, 0x83 },
+	{ 0x40041, 0x4f },
+	{ 0x40061, 0x0 },
+	{ 0x40002, 0x4040 },
+	{ 0x40022, 0x83 },
+	{ 0x40042, 0x51 },
+	{ 0x40062, 0x0 },
+	{ 0x40003, 0x811 },
+	{ 0x40023, 0x880 },
+	{ 0x40043, 0x0 },
+	{ 0x40063, 0x0 },
+	{ 0x40004, 0x720 },
+	{ 0x40024, 0xf },
+	{ 0x40044, 0x1740 },
+	{ 0x40064, 0x0 },
+	{ 0x40005, 0x16 },
+	{ 0x40025, 0x83 },
+	{ 0x40045, 0x4b },
+	{ 0x40065, 0x0 },
+	{ 0x40006, 0x716 },
+	{ 0x40026, 0xf },
+	{ 0x40046, 0x2001 },
+	{ 0x40066, 0x0 },
+	{ 0x40007, 0x716 },
+	{ 0x40027, 0xf },
+	{ 0x40047, 0x2800 },
+	{ 0x40067, 0x0 },
+	{ 0x40008, 0x716 },
+	{ 0x40028, 0xf },
+	{ 0x40048, 0xf00 },
+	{ 0x40068, 0x0 },
+	{ 0x40009, 0x720 },
+	{ 0x40029, 0xf },
+	{ 0x40049, 0x1400 },
+	{ 0x40069, 0x0 },
+	{ 0x4000a, 0xe08 },
+	{ 0x4002a, 0xc15 },
+	{ 0x4004a, 0x0 },
+	{ 0x4006a, 0x0 },
+	{ 0x4000b, 0x623 },
+	{ 0x4002b, 0x15 },
+	{ 0x4004b, 0x0 },
+	{ 0x4006b, 0x0 },
+	{ 0x4000c, 0x4028 },
+	{ 0x4002c, 0x80 },
+	{ 0x4004c, 0x0 },
+	{ 0x4006c, 0x0 },
+	{ 0x4000d, 0xe08 },
+	{ 0x4002d, 0xc1a },
+	{ 0x4004d, 0x0 },
+	{ 0x4006d, 0x0 },
+	{ 0x4000e, 0x623 },
+	{ 0x4002e, 0x1a },
+	{ 0x4004e, 0x0 },
+	{ 0x4006e, 0x0 },
+	{ 0x4000f, 0x4040 },
+	{ 0x4002f, 0x80 },
+	{ 0x4004f, 0x0 },
+	{ 0x4006f, 0x0 },
+	{ 0x40010, 0x2604 },
+	{ 0x40030, 0x15 },
+	{ 0x40050, 0x0 },
+	{ 0x40070, 0x0 },
+	{ 0x40011, 0x708 },
+	{ 0x40031, 0x5 },
+	{ 0x40051, 0x0 },
+	{ 0x40071, 0x2002 },
+	{ 0x40012, 0x8 },
+	{ 0x40032, 0x80 },
+	{ 0x40052, 0x0 },
+	{ 0x40072, 0x0 },
+	{ 0x40013, 0x2604 },
+	{ 0x40033, 0x1a },
+	{ 0x40053, 0x0 },
+	{ 0x40073, 0x0 },
+	{ 0x40014, 0x708 },
+	{ 0x40034, 0xa },
+	{ 0x40054, 0x0 },
+	{ 0x40074, 0x2002 },
+	{ 0x40015, 0x4040 },
+	{ 0x40035, 0x80 },
+	{ 0x40055, 0x0 },
+	{ 0x40075, 0x0 },
+	{ 0x40016, 0x60a },
+	{ 0x40036, 0x15 },
+	{ 0x40056, 0x1200 },
+	{ 0x40076, 0x0 },
+	{ 0x40017, 0x61a },
+	{ 0x40037, 0x15 },
+	{ 0x40057, 0x1300 },
+	{ 0x40077, 0x0 },
+	{ 0x40018, 0x60a },
+	{ 0x40038, 0x1a },
+	{ 0x40058, 0x1200 },
+	{ 0x40078, 0x0 },
+	{ 0x40019, 0x642 },
+	{ 0x40039, 0x1a },
+	{ 0x40059, 0x1300 },
+	{ 0x40079, 0x0 },
+	{ 0x4001a, 0x4808 },
+	{ 0x4003a, 0x880 },
+	{ 0x4005a, 0x0 },
+	{ 0x4007a, 0x0 },
+	{ 0x900a7, 0x0 },
+	{ 0x900a8, 0x790 },
+	{ 0x900a9, 0x11a },
+	{ 0x900aa, 0x8 },
+	{ 0x900ab, 0x7aa },
+	{ 0x900ac, 0x2a },
+	{ 0x900ad, 0x10 },
+	{ 0x900ae, 0x7b2 },
+	{ 0x900af, 0x2a },
+	{ 0x900b0, 0x0 },
+	{ 0x900b1, 0x7c8 },
+	{ 0x900b2, 0x109 },
+	{ 0x900b3, 0x10 },
+	{ 0x900b4, 0x2a8 },
+	{ 0x900b5, 0x129 },
+	{ 0x900b6, 0x8 },
+	{ 0x900b7, 0x370 },
+	{ 0x900b8, 0x129 },
+	{ 0x900b9, 0xa },
+	{ 0x900ba, 0x3c8 },
+	{ 0x900bb, 0x1a9 },
+	{ 0x900bc, 0xc },
+	{ 0x900bd, 0x408 },
+	{ 0x900be, 0x199 },
+	{ 0x900bf, 0x14 },
+	{ 0x900c0, 0x790 },
+	{ 0x900c1, 0x11a },
+	{ 0x900c2, 0x8 },
+	{ 0x900c3, 0x4 },
+	{ 0x900c4, 0x18 },
+	{ 0x900c5, 0xe },
+	{ 0x900c6, 0x408 },
+	{ 0x900c7, 0x199 },
+	{ 0x900c8, 0x8 },
+	{ 0x900c9, 0x8568 },
+	{ 0x900ca, 0x108 },
+	{ 0x900cb, 0x18 },
+	{ 0x900cc, 0x790 },
+	{ 0x900cd, 0x16a },
+	{ 0x900ce, 0x8 },
+	{ 0x900cf, 0x1d8 },
+	{ 0x900d0, 0x169 },
+	{ 0x900d1, 0x10 },
+	{ 0x900d2, 0x8558 },
+	{ 0x900d3, 0x168 },
+	{ 0x900d4, 0x70 },
+	{ 0x900d5, 0x788 },
+	{ 0x900d6, 0x16a },
+	{ 0x900d7, 0x1ff8 },
+	{ 0x900d8, 0x85a8 },
+	{ 0x900d9, 0x1e8 },
+	{ 0x900da, 0x50 },
+	{ 0x900db, 0x798 },
+	{ 0x900dc, 0x16a },
+	{ 0x900dd, 0x60 },
+	{ 0x900de, 0x7a0 },
+	{ 0x900df, 0x16a },
+	{ 0x900e0, 0x8 },
+	{ 0x900e1, 0x8310 },
+	{ 0x900e2, 0x168 },
+	{ 0x900e3, 0x8 },
+	{ 0x900e4, 0xa310 },
+	{ 0x900e5, 0x168 },
+	{ 0x900e6, 0xa },
+	{ 0x900e7, 0x408 },
+	{ 0x900e8, 0x169 },
+	{ 0x900e9, 0x6e },
+	{ 0x900ea, 0x0 },
+	{ 0x900eb, 0x68 },
+	{ 0x900ec, 0x0 },
+	{ 0x900ed, 0x408 },
+	{ 0x900ee, 0x169 },
+	{ 0x900ef, 0x0 },
+	{ 0x900f0, 0x8310 },
+	{ 0x900f1, 0x168 },
+	{ 0x900f2, 0x0 },
+	{ 0x900f3, 0xa310 },
+	{ 0x900f4, 0x168 },
+	{ 0x900f5, 0x1ff8 },
+	{ 0x900f6, 0x85a8 },
+	{ 0x900f7, 0x1e8 },
+	{ 0x900f8, 0x68 },
+	{ 0x900f9, 0x798 },
+	{ 0x900fa, 0x16a },
+	{ 0x900fb, 0x78 },
+	{ 0x900fc, 0x7a0 },
+	{ 0x900fd, 0x16a },
+	{ 0x900fe, 0x68 },
+	{ 0x900ff, 0x790 },
+	{ 0x90100, 0x16a },
+	{ 0x90101, 0x8 },
+	{ 0x90102, 0x8b10 },
+	{ 0x90103, 0x168 },
+	{ 0x90104, 0x8 },
+	{ 0x90105, 0xab10 },
+	{ 0x90106, 0x168 },
+	{ 0x90107, 0xa },
+	{ 0x90108, 0x408 },
+	{ 0x90109, 0x169 },
+	{ 0x9010a, 0x58 },
+	{ 0x9010b, 0x0 },
+	{ 0x9010c, 0x68 },
+	{ 0x9010d, 0x0 },
+	{ 0x9010e, 0x408 },
+	{ 0x9010f, 0x169 },
+	{ 0x90110, 0x0 },
+	{ 0x90111, 0x8b10 },
+	{ 0x90112, 0x168 },
+	{ 0x90113, 0x0 },
+	{ 0x90114, 0xab10 },
+	{ 0x90115, 0x168 },
+	{ 0x90116, 0x0 },
+	{ 0x90117, 0x1d8 },
+	{ 0x90118, 0x169 },
+	{ 0x90119, 0x80 },
+	{ 0x9011a, 0x790 },
+	{ 0x9011b, 0x16a },
+	{ 0x9011c, 0x18 },
+	{ 0x9011d, 0x7aa },
+	{ 0x9011e, 0x6a },
+	{ 0x9011f, 0xa },
+	{ 0x90120, 0x0 },
+	{ 0x90121, 0x1e9 },
+	{ 0x90122, 0x8 },
+	{ 0x90123, 0x8080 },
+	{ 0x90124, 0x108 },
+	{ 0x90125, 0xf },
+	{ 0x90126, 0x408 },
+	{ 0x90127, 0x169 },
+	{ 0x90128, 0xc },
+	{ 0x90129, 0x0 },
+	{ 0x9012a, 0x68 },
+	{ 0x9012b, 0x9 },
+	{ 0x9012c, 0x0 },
+	{ 0x9012d, 0x1a9 },
+	{ 0x9012e, 0x0 },
+	{ 0x9012f, 0x408 },
+	{ 0x90130, 0x169 },
+	{ 0x90131, 0x0 },
+	{ 0x90132, 0x8080 },
+	{ 0x90133, 0x108 },
+	{ 0x90134, 0x8 },
+	{ 0x90135, 0x7aa },
+	{ 0x90136, 0x6a },
+	{ 0x90137, 0x0 },
+	{ 0x90138, 0x8568 },
+	{ 0x90139, 0x108 },
+	{ 0x9013a, 0xb7 },
+	{ 0x9013b, 0x790 },
+	{ 0x9013c, 0x16a },
+	{ 0x9013d, 0x1f },
+	{ 0x9013e, 0x0 },
+	{ 0x9013f, 0x68 },
+	{ 0x90140, 0x8 },
+	{ 0x90141, 0x8558 },
+	{ 0x90142, 0x168 },
+	{ 0x90143, 0xf },
+	{ 0x90144, 0x408 },
+	{ 0x90145, 0x169 },
+	{ 0x90146, 0xc },
+	{ 0x90147, 0x0 },
+	{ 0x90148, 0x68 },
+	{ 0x90149, 0x0 },
+	{ 0x9014a, 0x408 },
+	{ 0x9014b, 0x169 },
+	{ 0x9014c, 0x0 },
+	{ 0x9014d, 0x8558 },
+	{ 0x9014e, 0x168 },
+	{ 0x9014f, 0x8 },
+	{ 0x90150, 0x3c8 },
+	{ 0x90151, 0x1a9 },
+	{ 0x90152, 0x3 },
+	{ 0x90153, 0x370 },
+	{ 0x90154, 0x129 },
+	{ 0x90155, 0x20 },
+	{ 0x90156, 0x2aa },
+	{ 0x90157, 0x9 },
+	{ 0x90158, 0x0 },
+	{ 0x90159, 0x400 },
+	{ 0x9015a, 0x10e },
+	{ 0x9015b, 0x8 },
+	{ 0x9015c, 0xe8 },
+	{ 0x9015d, 0x109 },
+	{ 0x9015e, 0x0 },
+	{ 0x9015f, 0x8140 },
+	{ 0x90160, 0x10c },
+	{ 0x90161, 0x10 },
+	{ 0x90162, 0x8138 },
+	{ 0x90163, 0x10c },
+	{ 0x90164, 0x8 },
+	{ 0x90165, 0x7c8 },
+	{ 0x90166, 0x101 },
+	{ 0x90167, 0x8 },
+	{ 0x90168, 0x0 },
+	{ 0x90169, 0x8 },
+	{ 0x9016a, 0x8 },
+	{ 0x9016b, 0x448 },
+	{ 0x9016c, 0x109 },
+	{ 0x9016d, 0xf },
+	{ 0x9016e, 0x7c0 },
+	{ 0x9016f, 0x109 },
+	{ 0x90170, 0x0 },
+	{ 0x90171, 0xe8 },
+	{ 0x90172, 0x109 },
+	{ 0x90173, 0x47 },
+	{ 0x90174, 0x630 },
+	{ 0x90175, 0x109 },
+	{ 0x90176, 0x8 },
+	{ 0x90177, 0x618 },
+	{ 0x90178, 0x109 },
+	{ 0x90179, 0x8 },
+	{ 0x9017a, 0xe0 },
+	{ 0x9017b, 0x109 },
+	{ 0x9017c, 0x0 },
+	{ 0x9017d, 0x7c8 },
+	{ 0x9017e, 0x109 },
+	{ 0x9017f, 0x8 },
+	{ 0x90180, 0x8140 },
+	{ 0x90181, 0x10c },
+	{ 0x90182, 0x0 },
+	{ 0x90183, 0x1 },
+	{ 0x90184, 0x8 },
+	{ 0x90185, 0x8 },
+	{ 0x90186, 0x4 },
+	{ 0x90187, 0x8 },
+	{ 0x90188, 0x8 },
+	{ 0x90189, 0x7c8 },
+	{ 0x9018a, 0x101 },
+	{ 0x90006, 0x0 },
+	{ 0x90007, 0x0 },
+	{ 0x90008, 0x8 },
+	{ 0x90009, 0x0 },
+	{ 0x9000a, 0x0 },
+	{ 0x9000b, 0x0 },
+	{ 0xd00e7, 0x400 },
+	{ 0x90017, 0x0 },
+	{ 0x9001f, 0x2a },
+	{ 0x90026, 0x6a },
+	{ 0x400d0, 0x0 },
+	{ 0x400d1, 0x101 },
+	{ 0x400d2, 0x105 },
+	{ 0x400d3, 0x107 },
+	{ 0x400d4, 0x10f },
+	{ 0x400d5, 0x202 },
+	{ 0x400d6, 0x20a },
+	{ 0x400d7, 0x20b },
+	{ 0x2003a, 0x2 },
+	{ 0x2000b, 0x5d },
+	{ 0x2000c, 0xbb },
+	{ 0x2000d, 0x753 },
+	{ 0x2000e, 0x2c },
+	{ 0x12000b, 0xc },
+	{ 0x12000c, 0x19 },
+	{ 0x12000d, 0xfa },
+	{ 0x12000e, 0x10 },
+	{ 0x22000b, 0x3 },
+	{ 0x22000c, 0x6 },
+	{ 0x22000d, 0x3e },
+	{ 0x22000e, 0x10 },
+	{ 0x9000c, 0x0 },
+	{ 0x9000d, 0x173 },
+	{ 0x9000e, 0x60 },
+	{ 0x9000f, 0x6110 },
+	{ 0x90010, 0x2152 },
+	{ 0x90011, 0xdfbd },
+	{ 0x90012, 0x60 },
+	{ 0x90013, 0x6152 },
+	{ 0x20010, 0x5a },
+	{ 0x20011, 0x3 },
+	{ 0x40080, 0xe0 },
+	{ 0x40081, 0x12 },
+	{ 0x40082, 0xe0 },
+	{ 0x40083, 0x12 },
+	{ 0x40084, 0xe0 },
+	{ 0x40085, 0x12 },
+	{ 0x140080, 0xe0 },
+	{ 0x140081, 0x12 },
+	{ 0x140082, 0xe0 },
+	{ 0x140083, 0x12 },
+	{ 0x140084, 0xe0 },
+	{ 0x140085, 0x12 },
+	{ 0x240080, 0xe0 },
+	{ 0x240081, 0x12 },
+	{ 0x240082, 0xe0 },
+	{ 0x240083, 0x12 },
+	{ 0x240084, 0xe0 },
+	{ 0x240085, 0x12 },
+	{ 0x400fd, 0xf },
+	{ 0x10011, 0x1 },
+	{ 0x10012, 0x1 },
+	{ 0x10013, 0x180 },
+	{ 0x10018, 0x1 },
+	{ 0x10002, 0x6209 },
+	{ 0x100b2, 0x1 },
+	{ 0x101b4, 0x1 },
+	{ 0x102b4, 0x1 },
+	{ 0x103b4, 0x1 },
+	{ 0x104b4, 0x1 },
+	{ 0x105b4, 0x1 },
+	{ 0x106b4, 0x1 },
+	{ 0x107b4, 0x1 },
+	{ 0x108b4, 0x1 },
+	{ 0x11011, 0x1 },
+	{ 0x11012, 0x1 },
+	{ 0x11013, 0x180 },
+	{ 0x11018, 0x1 },
+	{ 0x11002, 0x6209 },
+	{ 0x110b2, 0x1 },
+	{ 0x111b4, 0x1 },
+	{ 0x112b4, 0x1 },
+	{ 0x113b4, 0x1 },
+	{ 0x114b4, 0x1 },
+	{ 0x115b4, 0x1 },
+	{ 0x116b4, 0x1 },
+	{ 0x117b4, 0x1 },
+	{ 0x118b4, 0x1 },
+	{ 0x12011, 0x1 },
+	{ 0x12012, 0x1 },
+	{ 0x12013, 0x180 },
+	{ 0x12018, 0x1 },
+	{ 0x12002, 0x6209 },
+	{ 0x120b2, 0x1 },
+	{ 0x121b4, 0x1 },
+	{ 0x122b4, 0x1 },
+	{ 0x123b4, 0x1 },
+	{ 0x124b4, 0x1 },
+	{ 0x125b4, 0x1 },
+	{ 0x126b4, 0x1 },
+	{ 0x127b4, 0x1 },
+	{ 0x128b4, 0x1 },
+	{ 0x13011, 0x1 },
+	{ 0x13012, 0x1 },
+	{ 0x13013, 0x180 },
+	{ 0x13018, 0x1 },
+	{ 0x13002, 0x6209 },
+	{ 0x130b2, 0x1 },
+	{ 0x131b4, 0x1 },
+	{ 0x132b4, 0x1 },

board/freescale/imx8mm_evk/lpddr4_timing.c line 1935

Quoted 10 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +10 -0
+	{ 0x133b4, 0x1 },
+	{ 0x134b4, 0x1 },
+	{ 0x135b4, 0x1 },
+	{ 0x136b4, 0x1 },
+	{ 0x137b4, 0x1 },
+	{ 0x138b4, 0x1 },
+	{ 0x2003a, 0x2 },
+	{ 0xc0080, 0x2 },
+	{ 0xd0000, 0x1 },
+};

The same as above.

Quoted 44 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +15 -0
+
+struct dram_fsp_msg lpddr4_dram_fsp_msg[] = {
+	{
+		/* P0 3000mts 1D */
+		.drate = 3000,
+		.fw_type = FW_1D_IMAGE,
+		.fsp_cfg = lpddr4_fsp0_cfg,
+		.fsp_cfg_num = ARRAY_SIZE(lpddr4_fsp0_cfg),
+	},
+	{
+		/* P0 3000mts 2D */
+		.drate = 3000,
+		.fw_type = FW_2D_IMAGE,
+		.fsp_cfg = lpddr4_fsp0_2d_cfg,
+		.fsp_cfg_num =

ARRAY_SIZE(lpddr4_fsp0_2d_cfg),

board/freescale/imx8mm_evk/lpddr4_timing.c new file +27 -0
+	},
+	{
+		/* P1 400mts 1D */
+		.drate = 400,
+		.fw_type = FW_1D_IMAGE,
+		.fsp_cfg = lpddr4_fsp1_cfg,
+		.fsp_cfg_num = ARRAY_SIZE(lpddr4_fsp1_cfg),
+	},
+	{
+		/* P1 100mts 1D */
+		.drate = 100,
+		.fw_type = FW_1D_IMAGE,
+		.fsp_cfg = lpddr4_fsp2_cfg,
+		.fsp_cfg_num = ARRAY_SIZE(lpddr4_fsp2_cfg),
+	},
+};
+
+/* lpddr4 timing config params on EVK board */
+struct dram_timing_info dram_timing = {
+	.ddrc_cfg = lpddr4_ddrc_cfg,
+	.ddrc_cfg_num = ARRAY_SIZE(lpddr4_ddrc_cfg),
+	.ddrphy_cfg = lpddr4_ddrphy_cfg,
+	.ddrphy_cfg_num = ARRAY_SIZE(lpddr4_ddrphy_cfg),
+	.fsp_msg = lpddr4_dram_fsp_msg,
+	.fsp_msg_num = ARRAY_SIZE(lpddr4_dram_fsp_msg),
+	.ddrphy_trained_csr = lpddr4_ddrphy_trained_csr,
+	.ddrphy_trained_csr_num =

ARRAY_SIZE(lpddr4_ddrphy_trained_csr),

board/freescale/imx8mm_evk/lpddr4_timing.c line 1979

Quoted 2 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +2 -0
+	.ddrphy_pie = lpddr4_phy_pie,
+	.ddrphy_pie_num = ARRAY_SIZE(lpddr4_phy_pie),

It would be best to get the above values calculated dynamically for this SoC.

Quoted 29 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +1 -0
+};
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/spl.c new file mode 100644 index 0000000000..cf1dfc2c2a

board/freescale/imx8mm_evk/spl.c new file +22 -0
@@ -0,0 +1,187 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/arch/imx8mm_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <power/pmic.h>
+#include <asm/arch/clock.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <asm/arch/ddr.h>
+
+DECLARE_GLOBAL_DATA_PTR;

board/freescale/imx8mm_evk/spl.c line 32

Quoted 10 lines
board/freescale/imx8mm_evk/spl.c new file +10 -0
+
+void spl_dram_init(void)
+{
+	ddr_init(&dram_timing);
+}
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(2, 18)
+#define USDHC2_PWR_GPIO IMX_GPIO_NR(2, 19)
+
+#define USDHC_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS |

PAD_CTL_PUE | \

Quoted 24 lines
board/freescale/imx8mm_evk/spl.c new file +5 -0
+			PAD_CTL_PE | PAD_CTL_FSEL2)
+#define USDHC_GPIO_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE1)
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	IMX8MM_PAD_NAND_WE_B_USDHC3_CLK |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_WP_B_USDHC3_CMD |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_DATA04_USDHC3_DATA0 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_DATA05_USDHC3_DATA1 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_DATA06_USDHC3_DATA2 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_DATA07_USDHC3_DATA3 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_RE_B_USDHC3_DATA4 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_CE2_B_USDHC3_DATA5 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_CE3_B_USDHC3_DATA6 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_CLE_USDHC3_DATA7 |

MUX_PAD_CTRL(USDHC_PAD_CTRL), +};

board/freescale/imx8mm_evk/spl.c

Quoted 3 lines
board/freescale/imx8mm_evk/spl.c new file +3 -0
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	IMX8MM_PAD_SD2_CLK_USDHC2_CLK |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c

Quoted 1 line
board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_CMD_USDHC2_CMD |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

Quoted 60 lines
board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_DATA0_USDHC2_DATA0 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_DATA1_USDHC2_DATA1 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_DATA2_USDHC2_DATA2 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_RESET_B_GPIO2_IO19 |

MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL), +};

board/freescale/imx8mm_evk/spl.c new file +4 -0
+
+/*
+ * The evk board uses DAT3 to detect CD card plugin,
+ * in u-boot we mux the pin to GPIO when doing

board_mmc_getcd.
+ */

board/freescale/imx8mm_evk/spl.c new file +2 -0
+static iomux_v3_cfg_t const usdhc2_cd_pad =
+	IMX8MM_PAD_SD2_DATA3_GPIO2_IO18 |

MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL); +

board/freescale/imx8mm_evk/spl.c new file +14 -0
+static iomux_v3_cfg_t const usdhc2_dat3_pad =
+	IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 |
+	MUX_PAD_CTRL(USDHC_PAD_CTRL);
+
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+	{USDHC2_BASE_ADDR, 0, 1},
+	{USDHC3_BASE_ADDR, 0, 1},
+};
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+	/*
+	 * According to the board_mmc_init() the following

map is done:

board/freescale/imx8mm_evk/spl.c new file +8 -0
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0                    USDHC1
+	 * mmc1                    USDHC2
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			usdhc_cfg[0].sdhc_clk =

mxc_get_clock(MXC_ESDHC2_CLK);
+
imx_iomux_v3_setup_multiple_pads(usdhc2_pads, + ARRAY_SIZE(usdhc2_pads));

board/freescale/imx8mm_evk/spl.c new file +1 -0
+			gpio_request(USDHC2_PWR_GPIO,

"usdhc2_reset");
+
gpio_direction_output(USDHC2_PWR_GPIO, 0);

board/freescale/imx8mm_evk/spl.c new file +2 -0
+			udelay(500);
+

gpio_direction_output(USDHC2_PWR_GPIO, 1);

board/freescale/imx8mm_evk/spl.c new file +3 -0
+			break;
+		case 1:
+			usdhc_cfg[1].sdhc_clk =

mxc_get_clock(MXC_ESDHC3_CLK);
+
imx_iomux_v3_setup_multiple_pads(usdhc3_pads, + ARRAY_SIZE(usdhc3_pads));

board/freescale/imx8mm_evk/spl.c

Quoted 1 line
board/freescale/imx8mm_evk/spl.c new file +1 -0
+			break;

It would be best if you could enable DM/DTS in SPL too from the outset (and share the SPL size).

Do you have any timeline for converting SPL to DM/DTS?

Quoted 105 lines
board/freescale/imx8mm_evk/spl.c new file +2 -0
+		default:
+			printf("USDHC controllers %d not

supported \n", i + 1);

board/freescale/imx8mm_evk/spl.c new file +4 -0
+			return -EINVAL;
+		}
+
+		ret = fsl_esdhc_initialize(bis,

&usdhc_cfg[i]);

board/freescale/imx8mm_evk/spl.c new file +10 -0
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg

*)mmc->priv;

board/freescale/imx8mm_evk/spl.c new file +13 -0
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC3_BASE_ADDR:
+		ret = 1;
+		break;
+	case USDHC2_BASE_ADDR:
+		imx_iomux_v3_setup_pad(usdhc2_cd_pad);
+		gpio_request(USDHC2_CD_GPIO, "usdhc2 cd");
+		gpio_direction_input(USDHC2_CD_GPIO);
+
+		/*
[… more lines in the raw message]

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

pulled to

board/freescale/imx8mm_evk/spl.c new file +20 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

choose */

board/freescale/imx8mm_evk/spl.c new file +39 -0

Lines of this file are not shown. View the raw message.

(quoted diff) +0 -0

The rest of this diff is not shown. View the raw message.

b/configs/imx8mm_evk_defconfig new file mode 100644 index 0000000000..6110f23e38

configs/imx8mm_evk_defconfig new file +6 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Quoted 8 lines
Quoted 8 lines
Quoted 7 lines
Quoted 7 lines

configs/imx8mm_evk_defconfig

Quoted 7 lines
configs/imx8mm_evk_defconfig new file +6 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

+CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"

Quoted 3 lines
Quoted 3 lines
Quoted 2 lines
Quoted 2 lines
Quoted 1 line

+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/imx8m

Quoted 49 lines
Quoted 49 lines
Quoted 49 lines
Quoted 49 lines

/imximage.cfg,SPL_TEXT_BASE=0x7E1000"

configs/imx8mm_evk_defconfig

Quoted 20 lines
configs/imx8mm_evk_defconfig new file +20 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Here you enable the DM_ETH, but the welcome u-boot info says:

"Net: No ethernet found."

Quoted 23 lines
configs/imx8mm_evk_defconfig new file +7 -0

Lines of this file are not shown. View the raw message.

(quoted diff) +0 -0

The rest of this diff is not shown. View the raw message.

b/include/configs/imx8mm_evk.h new file mode 100644 index 0000000000..f944308757

include/configs/imx8mm_evk.h new file +10 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

include/configs/imx8mm_evk.h

Quoted 8 lines
include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

region */ +#endif

include/configs/imx8mm_evk.h new file +4 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR

Quoted 160 lines
Quoted 160 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line

+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR

	0x300
Quoted 15 lines
Quoted 15 lines

include/configs/imx8mm_evk.h

Quoted 3 lines
include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR *

Quoted 10 lines

512) +

include/configs/imx8mm_evk.h new file +6 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
+#define CONFIG_SPL_STACK 0x91fff0 +#define
CONFIG_SPL_LIBCOMMON_SUPPORT +#define

CONFIG_SPL_LIBGENERIC_SUPPORT

Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

*/ +#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 /* 512
KB */ +#define CONFIG_SYS_ICACHE_OFF

include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

malloc f used before GD_FLG_FULL_MALLOC_INIT set */ + +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image

gives a

Quoted 132 lines
Quoted 132 lines

error

include/configs/imx8mm_evk.h

Quoted 4 lines

info not panic */ +

include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Why do you need to undef those config options?

include/configs/imx8mm_evk.h

Quoted 20 lines
include/configs/imx8mm_evk.h new file +20 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

There seems to be some issue with inheritance, as you need to undef those values manually.

Why is it needed?

Quoted 98 lines
include/configs/imx8mm_evk.h new file +27 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

earlycon=ec_imx6q,0x30890000,115200\0" \

include/configs/imx8mm_evk.h new file +8 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

"\0" \

include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

root=${mmcroot}\0 " \

include/configs/imx8mm_evk.h new file +1 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${loadaddr} ${script};\0" \

include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${loadaddr} ${image}\0" \

include/configs/imx8mm_evk.h new file +1 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${fdt_file}\0" \

include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${boot_fdt} = try; then " \

include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${fdt_addr}; " \

include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

DT; " \

include/configs/imx8mm_evk.h new file +5 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

console=${console} " \

include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

nfsroot=${serverip}:${nfsroot},v3,tcp\0" \

include/configs/imx8mm_evk.h new file +9 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${boot_fdt} = try; then " \

include/configs/imx8mm_evk.h new file +1 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${fdt_file}; then " \

include/configs/imx8mm_evk.h new file +1 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${fdt_addr}; " \

include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

DT; " \

include/configs/imx8mm_evk.h new file +13 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

include/configs/imx8mm_evk.h

Quoted 8 lines
include/configs/imx8mm_evk.h new file +8 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

CONFIG_LOADADDR

Quoted 74 lines
Quoted 74 lines
Quoted 74 lines
Quoted 74 lines

include/configs/imx8mm_evk.h

Quoted 25 lines
include/configs/imx8mm_evk.h new file +7 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

CONFIG_SYS_INIT_SP_OFFSET) +

include/configs/imx8mm_evk.h new file +6 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

*/ +#define
CONFIG_MMCROOT "/dev/mmcblk1p2" /*
USDHC2 */ + +/* Size of malloc() pool */

include/configs/imx8mm_evk.h new file +5 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

2GB DDR */ +

include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

(CONFIG_SYS_MEMTEST_START +

Quoted 32 lines

(PHYS_SDRAM_SIZE >> 1)) +

include/configs/imx8mm_evk.h new file +13 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

sizeof(CONFIG_SYS_PROMPT) + 16) +

include/configs/imx8mm_evk.h new file +17 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Quoted 4 lines

bus 1 */ +#define CONFIG_SYS_I2C_MXC_I2C2 /*
enable I2C bus 2 */ +#define
CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED 100000

Some of those values are (SYS_I2C_*, MXC_OCOTP, FSL_*) are already supported by Kconfig. Please use Kconfig instead.

include/configs/imx8mm_evk.h

Quoted 4 lines
include/configs/imx8mm_evk.h new file +4 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Best regards,

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director:

Wolfgang

Quoted 9 lines
Quoted 9 lines
Quoted 3 lines
Quoted 3 lines

Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-59 Fax:
(+49)-8142-66989-80 Email: lukma at denx.de

Best regards,

Quoted 8 lines
Quoted 8 lines

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang
Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
lukma at denx.de

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
lukma at denx.de

Part of the diff is not shown here. View the raw message.

#38 lore raw

PATCH 20/20 imx: add i.MX8MM EVK board support

Hi Peng,

Quoted 90 lines
Quoted 90 lines

-----Original Message-----
From: Lukasz Majewski [mailto:lukma at denx.de]
Sent: 2019年1月30日 16:38
To: Peng Fan <[email protected]>
Cc: sbabic at denx.de; Fabio Estevam <[email protected]>; dl-uboot-imx <[email protected]>; u-boot at lists.denx.de
Subject: Re: [U-Boot] [PATCH 20/20] imx: add i.MX8MM EVK board support

Quoted 65 lines · On Wed, 30 Jan 2019 07:07:10 +0000 Peng Fan <[email protected]> wrote:
Quoted 65 lines

-----Original Message-----
From: Lukasz Majewski [mailto:lukma at denx.de]
Sent: 2019年1月30日 14:54
To: Peng Fan <[email protected]>
Cc: sbabic at denx.de; Fabio Estevam <[email protected]>; dl-uboot-imx <[email protected]>; u-boot at lists.denx.de
Subject: Re: [U-Boot] [PATCH 20/20] imx: add i.MX8MM EVK board support

Hi Peng,

Quoted 34 lines
Quoted 34 lines

-----Original Message-----
From: Lukasz Majewski [mailto:lukma at denx.de]
Sent: 2019年1月30日 7:19
To: Peng Fan <[email protected]>
Cc: sbabic at denx.de; Fabio Estevam <[email protected]>; dl-uboot-imx <[email protected]>; u-boot at lists.denx.de
Subject: Re: [U-Boot] [PATCH 20/20] imx: add i.MX8MM EVK board support

Hi Peng,

Quoted 22 lines

Add i.MX8MM EVK board support.

Add board and SoC dts
Add ddr training code
support SD/MMC/GPIO/PINCTRL/UART

U-Boot SPL 2019.01-00148-g1179cffe66 (Jan 28 2019 - 17:37:34 +0800) Normal Boot
Trying to boot from MMC1

U-Boot 2019.01-00148-g1179cffe66 (Jan 28 2019 - 17:37:34 +0800)

CPU:   Freescale i.MX8MMQ rev1.0 at 1200 MHz
Reset cause: POR
Model: NXP i.MX8MM EVK board
DRAM:  2 GiB
MMC:   FSL_SDHC: 1, FSL_SDHC: 2
In:    serial
Out:   serial
Err:   serial

DM

Quoted 4 lines
Quoted 2 lines

You set/adjust latter in the code the fec network driver. Why it is not found?

I dropped network support, could add it in V2.

From the patch it seems like the ETH is fully supported, at lease from the source code point of view.

Quoted 11 lines
Quoted 3 lines

Could you also share the output of "dm tree" command?

Sure.

Quoted 3 lines

I suppose/guess that this board shall support as much as possible of the DT/DM conversions?

Ok.

Quoted 7 lines
Quoted 5 lines

And I would like to emphasize the need of DDR training code (as a functions, not pair of offset and value).

Are you able to provide such code in the next version of the patch?

There is already common code under drivers/ddr/imx8m

Yes. Indeed there code is there.

Quoted 2 lines

For the array in board file, It need ddr tool change, out of my knowledge.

Quoted 7 lines
Quoted 3 lines

If the code is there - why not use it for this board? In that way we would kill two birds with one stone - the code would be tested on "blessed" NXP's development board.

It is already used. The lpddr4_timing.c in board file is to provide configuration and the code in drivers/ddr/imx8m will use that to configure DDRC and DDR PHY.

Sorry to ask this - maybe I've misunderstood something. If we already use the training code - why do we need to pass the long set of "offset, value" tuples?

Quoted 4,033 lines

Thanks,
Peng.

Quoted 4,029 lines
Quoted 17 lines

Thanks,
Peng.

Quoted 12 lines
Quoted 12 lines

Regards,
Peng.

Quoted 7 lines
Quoted 7 lines

Hit any key to stop autoboot: 2

---
 arch/arm/dts/fsl-imx8mm-evk.dts            |  203 +++
 arch/arm/dts/fsl-imx8mm.dtsi               |  586  

++++++++

Quoted 202 lines
Quoted 202 lines
Quoted 202 lines
Quoted 202 lines
Quoted 202 lines
 arch/arm/mach-imx/imx8m/Kconfig            |    7 +
 board/freescale/imx8mm_evk/Kconfig         |   12 +
 board/freescale/imx8mm_evk/MAINTAINERS     |    6 +
 board/freescale/imx8mm_evk/Makefile        |   12 +
 board/freescale/imx8mm_evk/imx8mm_evk.c    |  144 ++
 board/freescale/imx8mm_evk/lpddr4_timing.c | 1980
++++++++++++++++++++++++++++
board/freescale/imx8mm_evk/spl.c           |  187 +++
configs/imx8mm_evk_defconfig               |   41 +
include/configs/imx8mm_evk.h               |  221 ++++ 11

files changed, 3399 insertions(+) create mode 100644 arch/arm/dts/fsl-imx8mm-evk.dts create mode 100644 arch/arm/dts/fsl-imx8mm.dtsi create mode 100644 board/freescale/imx8mm_evk/Kconfig create mode 100644 board/freescale/imx8mm_evk/MAINTAINERS create mode 100644 board/freescale/imx8mm_evk/Makefile create mode 100644 board/freescale/imx8mm_evk/imx8mm_evk.c create mode 100644 board/freescale/imx8mm_evk/lpddr4_timing.c create mode 100644 board/freescale/imx8mm_evk/spl.c create mode 100644 configs/imx8mm_evk_defconfig create mode 100644 include/configs/imx8mm_evk.h

(quoted diff) +0 -0

b/arch/arm/dts/fsl-imx8mm-evk.dts new file mode 100644 index 0000000000..df409eca47

arch/arm/dts/fsl-imx8mm-evk.dts new file +26 -0
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+
+/dts-v1/;
+
+#include "fsl-imx8mm.dtsi"
+
+/ {
+	model = "NXP i.MX8MM EVK board";
+	compatible = "fsl,imx8mm-evk", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_usdhc2_vmmc: regulator-usdhc2 {
+			compatible = "regulator-fixed";
+			regulator-name = "VSD_3V3";
+			regulator-min-microvolt =

<3300000>;

arch/arm/dts/fsl-imx8mm-evk.dts new file +1 -0
+			regulator-max-microvolt =

<3300000>;

arch/arm/dts/fsl-imx8mm-evk.dts new file +1 -0
+			gpio = <&gpio2 19

GPIO_ACTIVE_HIGH>;

arch/arm/dts/fsl-imx8mm-evk.dts new file +13 -0
+			off-on-delay = <20000>;
+			enable-active-high;
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	imx8mm-evk {
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+

MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+
MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+
MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+
MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+
MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+
MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+
MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+
MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+
MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+
MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+
MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+
MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+
MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+
MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+
MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_gpio_led: gpioledgrp {
+			fsl,pins = <
+

MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <
+

MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
+
MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc2_gpio: usdhc2grpgpio {
+			fsl,pins = <
+

MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x1c4
+
MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+

MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+
MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+			fsl,pins = <
+

MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+
MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+			fsl,pins = <
+

MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+
MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc3: usdhc3grp {
+			fsl,pins = <
+

MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
+
MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
+
MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
+
MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
+
MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
+
MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
+
MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

+
MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
+
MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
+
MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
+
MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE

	0x190  
Quoted 19 lines
Quoted 19 lines
Quoted 19 lines
Quoted 19 lines
Quoted 19 lines
arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+			fsl,pins = <
+

MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
+
MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
+
MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+
MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+
MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+
MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+
MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

+
MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+
MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+
MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+
MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE

	0x194  
Quoted 251 lines
Quoted 251 lines
Quoted 251 lines
Quoted 251 lines
Quoted 251 lines
arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+			fsl,pins = <
+

MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
+
MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
+
MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
+
MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
+
MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
+
MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
+
MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
+
MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
+
MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
+
MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
+
MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196

arch/arm/dts/fsl-imx8mm-evk.dts new file +6 -0
+			>;
+		};
+
+		pinctrl_wdog: wdoggrp {
+			fsl,pins = <
+

MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6

arch/arm/dts/fsl-imx8mm-evk.dts new file +13 -0
+			>;
+		};
+	};
+};
+
+&uart2 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz",

"state_200mhz";

arch/arm/dts/fsl-imx8mm-evk.dts new file +1 -0
+	pinctrl-0 = <&pinctrl_usdhc2>,

<&pinctrl_usdhc2_gpio>;

arch/arm/dts/fsl-imx8mm-evk.dts new file +1 -0
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>,

<&pinctrl_usdhc2_gpio>;

arch/arm/dts/fsl-imx8mm-evk.dts new file +1 -0
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>,

<&pinctrl_usdhc2_gpio>;

arch/arm/dts/fsl-imx8mm-evk.dts new file +8 -0
+	cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz",

"state_200mhz";

arch/arm/dts/fsl-imx8mm-evk.dts new file +14 -0
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
(quoted diff) +0 -0

b/arch/arm/dts/fsl-imx8mm.dtsi new file mode 100644 index 0000000000..8a808f856d

arch/arm/dts/fsl-imx8mm.dtsi new file +142 -0
@@ -0,0 +1,586 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2017-2019 NXP
+ */
+
+#include <dt-bindings/clock/imx8mm-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/pins-imx8mm.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	compatible = "fsl,imx8mm";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		spi0 = &ecspi1;
+		spi1 = &ecspi2;
+		spi2 = &ecspi3;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		mmc2 = &usdhc3;
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		A53_0: cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			next-level-cache = <&A53_L2>;
+		};
+
+		A53_1: cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			enable-method = "psci";
+			next-level-cache = <&A53_L2>;
+		};
+
+		A53_2: cpu at 2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x2>;
+			enable-method = "psci";
+			next-level-cache = <&A53_L2>;
+		};
+
+		A53_3: cpu at 3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x3>;
+			enable-method = "psci";
+			next-level-cache = <&A53_L2>;
+		};
+
+		A53_L2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	memory at 40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		osc_32k: clock at 0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "osc_32k";
+		};
+
+		osc_24m: clock at 1 {
+			compatible = "fixed-clock";
+			reg = <1>;
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+			clock-output-names = "osc_24m";
+		};
+
+		clk_ext1: clock at 2 {
+			compatible = "fixed-clock";
+			reg = <3>;
+			#clock-cells = <0>;
+			clock-frequency = <133000000>;
+			clock-output-names = "clk_ext1";
+		};
+
+		clk_ext2: clock at 3 {
+			compatible = "fixed-clock";
+			reg = <4>;
+			#clock-cells = <0>;
+			clock-frequency = <133000000>;
+			clock-output-names = "clk_ext2";
+		};
+
+		clk_ext3: clock at 4 {
+			compatible = "fixed-clock";
+			reg = <5>;
+			#clock-cells = <0>;
+			clock-frequency = <133000000>;
+			clock-output-names = "clk_ext3";
+		};
+
+		clk_ext4: clock at 5 {
+			compatible = "fixed-clock";
+			reg = <6>;
+			#clock-cells = <0>;
+			clock-frequency= <133000000>;
+			clock-output-names = "clk_ext4";
+		};
+	};
+
+	gic: interrupt-controller at 38800000 {
+		compatible = "arm,gic-v3";
+		reg = <0x0 0x38800000 0 0x10000>, /* GIC

Dist */

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+		      <0x0 0x38880000 0 0xC0000>; /* GICR

(RD_base + SGI_base) */

arch/arm/dts/fsl-imx8mm.dtsi new file +3 -0
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9

IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +11 -0
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7
+			(GIC_CPU_MASK_SIMPLE(6) |  

IRQ_TYPE_LEVEL_HIGH)>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+		interrupt-affinity = <&A53_0>, <&A53_1>,

<&A53_2>, <&A53_3>;

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Physical Secure */

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+			     <GIC_PPI 14

(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Physical Non-Secure */

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+			     <GIC_PPI 11

(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Virtual

*/

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+			     <GIC_PPI 10

(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>; /*

Hypervisor

Quoted 685 lines
Quoted 685 lines
Quoted 685 lines
Quoted 685 lines
Quoted 649 lines

*/

arch/arm/dts/fsl-imx8mm.dtsi new file +12 -0
+		clock-frequency = <8000000>;
+		arm,no-tick-in-suspend;
+	};
+
+	soc at 0 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		aips1: bus at 30000000 {
+			compatible = "fsl,aips-bus",

"simple-bus";

arch/arm/dts/fsl-imx8mm.dtsi new file +3 -0
+			#address-cells = <2>;
+			#size-cells = <2>;
+			reg = <0x0 0x30000000 0x0

0x400000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+			ranges;
+
+			gpio1: gpio at 30200000 {
+				compatible =

"fsl,imx8mm-gpio", "fsl,imx35-gpio";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30200000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

64 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					     <GIC_SPI

65 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio2: gpio at 30210000 {
+				compatible =

"fsl,imx8mm-gpio", "fsl,imx35-gpio";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30210000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

66 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					     <GIC_SPI

67 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio3: gpio at 30220000 {
+				compatible =

"fsl,imx8mm-gpio", "fsl,imx35-gpio";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30220000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

68 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					     <GIC_SPI

69 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio4: gpio at 30230000 {
+				compatible =

"fsl,imx8mm-gpio", "fsl,imx35-gpio";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30230000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

70 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					     <GIC_SPI

71 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio5: gpio at 30240000 {
+				compatible =

"fsl,imx8mm-gpio", "fsl,imx35-gpio";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30240000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

72 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					     <GIC_SPI

73 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +8 -0
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			wdog1: wdog at 30280000 {
+				compatible =

"fsl,imx21-wdt";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0 0x30280000 0  

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

78 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_WDOG1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				status = "disabled";
+			};
+
+			wdog2: wdog at 30290000 {
+				compatible =

"fsl,imx21-wdt";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0 0x30290000 0  

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

79 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_WDOG2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				status = "disabled";
+			};
+
+			wdog3: wdog at 302a0000 {
+				compatible =

"fsl,imx21-wdt";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0 0x302a0000 0  

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

10 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_WDOG3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				status = "disabled";
+			};
+
+			sdma2: dma-controller at 302c0000 {
+				compatible =

"fsl,imx8mq-sdma", "fsl,imx7d-sdma";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x302c0000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

103 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_SDMA2_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_SDMA2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"ahb";

arch/arm/dts/fsl-imx8mm.dtsi new file +2 -0
+				#dma-cells = <3>;
+				fsl,sdma-ram-script-name

= "imx/sdma/sdma-imx7d.bin";

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				fsl,ratio-1-1;
+				status = "okay";
+			};
+
+			sdma3: dma-controller at 302b0000 {
+				compatible =

"fsl,imx8mq-sdma", "fsl,imx7d-sdma";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x302b0000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

34 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_SDMA3_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				 <&clk  

IMX8MM_CLK_SDMA3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"ahb";

arch/arm/dts/fsl-imx8mm.dtsi new file +2 -0
+				#dma-cells = <3>;
+				fsl,sdma-ram-script-name

= "imx/sdma/sdma-imx7d.bin";

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				fsl,ratio-1-1;
+				status = "okay";
+			};
+
+			iomuxc: pinctrl at 30330000 {
+				compatible =

"fsl,imx8mm-iomuxc";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30330000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+			};
+
+			gpr: iomuxc-gpr at 30340000 {
+				compatible =

"fsl,imx8mm-iomuxc-gpr", "syscon";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30340000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+			};
+
+			ocotp: ocotp-ctrl at 30350000 {
+				compatible =

"fsl,imx8mq-ocotp", "fsl,imx7d-ocotp", "syscon";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0 0x30350000 0  

0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_OCOTP_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				/* For nvmem subnodes */
+				#address-cells = <1>;
+				#size-cells = <1>;
+			};
+
+			anatop: anatop at 30360000 {
+				compatible =

"fsl,imx8mm-anatop", "syscon", "simple-bus";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30360000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+			};
+
+			snvs: snvs at 30370000 {
+				compatible =

"fsl,sec-v4.0-mon","syscon", "simple-mfd";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30370000

0x0
0x10000>; +

arch/arm/dts/fsl-imx8mm.dtsi new file +2 -0
+				snvs_rtc: snvs-rtc-lp{
+					compatible =

"fsl,sec-v4.0-mon-rtc-lp";

arch/arm/dts/fsl-imx8mm.dtsi new file +3 -0
+					regmap =<&snvs>;
+					offset = <0x34>;
+					interrupts =

<GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+
<GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +3 -0
+				};
+
+				snvs_pwrkey:

snvs-powerkey {

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					compatible =

"fsl,sec-v4.0-pwrkey";

arch/arm/dts/fsl-imx8mm.dtsi new file +2 -0
+					regmap = <&snvs>;
+					interrupts =

<GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					linux,keycode =

<KEY_POWER>;

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+					wakeup-source;
+				};
+			};
+
+			clk: clock-controller at 30380000 {
+				compatible =

"fsl,imx8mm-ccm";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30380000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +2 -0
+				#clock-cells = <1>;
+				clocks = <&osc_32k>,

<&osc_24m>, <&clk_ext1>, <&clk_ext2>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk_ext3>,

<&clk_ext4>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "osc_32k",

"osc_24m", "clk_ext1", "clk_ext2",

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					      "clk_ext3",

"clk_ext4";

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+			};
+
+			src: src at 30390000 {
+				compatible =

"fsl,imx8mm-src", "syscon";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30390000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

89 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				#reset-cells = <1>;
+			};
+
+			gpc: gpc at 303a0000 {
+				compatible =

"fsl,imx8mm-gpc", "syscon";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x303a0000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +2 -0
+				interrupt-controller;
+				interrupts = <GIC_SPI

87 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				#interrupt-cells = <3>;
+			};
+		};
+
+		aips2: bus at 30400000 {
+			compatible = "fsl,aips-bus",

"simple-bus";

arch/arm/dts/fsl-imx8mm.dtsi new file +3 -0
+			#address-cells = <2>;
+			#size-cells = <2>;
+			reg = <0x0 0x30400000 0x0

0x400000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +4 -0
+			ranges;
+
+			pwm1: pwm at 30660000 {
+				compatible =

"fsl,imx8mm-pwm", "fsl,imx27-pwm";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30660000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

81 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_PWM1_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					<&clk  

IMX8MM_CLK_PWM1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				#pwm-cells = <2>;
+				status = "disabled";
+			};
+
+			pwm2: pwm at 30670000 {
+				compatible =

"fsl,imx8mm-pwm", "fsl,imx27-pwm";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30670000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

82 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_PWM2_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_PWM2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				#pwm-cells = <2>;
+				status = "disabled";
+			};
+
+			pwm3: pwm at 30680000 {
+				compatible =

"fsl,imx8mm-pwm", "fsl,imx27-pwm";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30680000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

83 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_PWM3_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_PWM3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+				#pwm-cells = <2>;
+				status = "disabled";
+			};
+
+			pwm4: pwm at 30690000 {
+				compatible =

"fsl,imx8mm-pwm", "fsl,imx27-pwm";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30690000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

84 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_PWM4_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_PWM4_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				#pwm-cells = <2>;
+				status = "disabled";
+			};
+		};
+
+		aips3: bus at 30800000 {
+			compatible = "fsl,aips-bus",

"simple-bus";

arch/arm/dts/fsl-imx8mm.dtsi new file +3 -0
+			#address-cells = <2>;
+			#size-cells = <2>;
+			reg = <0x0 0x30800000 0x0

0x400000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +6 -0
+			ranges;
+
+			ecspi1: ecspi at 30820000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-ecspi", "fsl,imx51-ecspi";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30820000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

31 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_ECSPI1_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_ECSPI1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				status = "disabled";
+			};
+
+			ecspi2: ecspi at 30830000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-ecspi", "fsl,imx51-ecspi";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30830000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

32 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_ECSPI2_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_ECSPI2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				status = "disabled";
+			};
+
+			ecspi3: ecspi at 30840000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-ecspi", "fsl,imx51-ecspi";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30840000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

33 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_ECSPI3_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_ECSPI3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				status = "disabled";
+			};
+
+			uart1: serial at 30860000 {
+				compatible =

"fsl,imx8mm-uart",
+
"fsl,imx6q-uart", "fsl,imx21-uart";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30860000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

26 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_UART1_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_UART1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				status = "disabled";
+			};
+
+			uart3: serial at 30880000 {
+				compatible =

"fsl,imx8mm-uart",
+
"fsl,imx6q-uart", "fsl,imx21-uart";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30880000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

28 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_UART3_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_UART3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				status = "disabled";
+			};
+
+			uart2: serial at 30890000 {
+				compatible =

"fsl,imx8mm-uart",
+
"fsl,imx6q-uart", "fsl,imx21-uart";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30890000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

27 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_UART2_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_UART2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				status = "disabled";
+			};
+
+			i2c1: i2c at 30a20000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-i2c", "fsl,imx21-i2c";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30a20000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

35 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_I2C1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				status = "disabled";
+			};
+
+			i2c2: i2c at 30a30000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-i2c", "fsl,imx21-i2c";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30a30000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

36 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_I2C2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				status = "disabled";
+			};
+
+			i2c3: i2c at 30a40000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-i2c", "fsl,imx21-i2c";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30a40000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

37 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_I2C3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				status = "disabled";
+			};
+
+			i2c4: i2c at 30a50000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible =

"fsl,imx8mm-i2c", "fsl,imx21-i2c";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30a50000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

38 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_I2C4_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				status = "disabled";
+			};
+
+			uart4: serial at 30a60000 {
+				compatible =

"fsl,imx8mq-uart",
+
"fsl,imx6q-uart", "fsl,imx21-uart";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30a60000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

29 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_UART4_ROOT>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_UART4_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"per";

arch/arm/dts/fsl-imx8mm.dtsi new file +5 -0
+				status = "disabled";
+			};
+
+			usdhc1: mmc at 30b40000 {
+				compatible =

"fsl,imx8mq-usdhc", "fsl,imx7d-usdhc";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30b40000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

22 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_DUMMY>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_NAND_USDHC_BUS>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_USDHC1_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"ahb", "per";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				assigned-clocks = <&clk  

IMX8MM_CLK_USDHC1>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				assigned-clock-rates =

<400000000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				fsl,tuning-start-tap =

<20>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				fsl,tuning-step= <2>;
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc2: mmc at 30b50000 {
+				compatible =

"fsl,imx8mq-usdhc", "fsl,imx7d-usdhc";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30b50000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

23 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_DUMMY>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_NAND_USDHC_BUS>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_USDHC2_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"ahb", "per";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				fsl,tuning-start-tap =

<20>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				fsl,tuning-step= <2>;
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc3: mmc at 30b60000 {
+				compatible =

"fsl,imx8mq-usdhc", "fsl,imx7d-usdhc";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				reg = <0x0 0x30b60000

0x0
0x10000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				interrupts = <GIC_SPI

24 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clocks = <&clk  

IMX8MM_CLK_DUMMY>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_NAND_USDHC_BUS>,

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+					 <&clk  

IMX8MM_CLK_USDHC3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				clock-names = "ipg",

"ahb", "per";

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				assigned-clocks = <&clk  

IMX8MM_CLK_USDHC3_ROOT>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				assigned-clock-rates =

<400000000>;

arch/arm/dts/fsl-imx8mm.dtsi new file +1 -0
+				fsl,tuning-start-tap =

<20>;

arch/arm/dts/fsl-imx8mm.dtsi new file +7 -0
+				fsl,tuning-step= <2>;
+				bus-width = <4>;
+				status = "disabled";
+			};
+		};
+	};
+};
(quoted diff) +0 -0
Quoted 2 lines

b/arch/arm/mach-imx/imx8m/Kconfig index
35c978e863..f520075875

100644

arch/arm/mach-imx/imx8m/Kconfig config TARGET_IMX8MQ_EVK · line 31

Quoted 11 lines
arch/arm/mach-imx/imx8m/Kconfig +5 -0
@@ -24,8 +24,15 @@ config TARGET_IMX8MQ_EVK
 	select IMX8MQ
 	select IMX8M_LPDDR4
 
+config TARGET_IMX8MM_EVK
+	bool "imx8mm LPDDR4 EVK board"
+	select IMX8MM
+	select SUPPORT_SPL
+	select IMX8M_LPDDR4  

Here you shall put the select DM_{UART,USDHC, etc}

Quoted 19 lines
arch/arm/mach-imx/imx8m/Kconfig +2 -0
+
 endchoice
 
 source "board/freescale/imx8mq_evk/Kconfig"
+source "board/freescale/imx8mm_evk/Kconfig"
 
 endif
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/Kconfig new file mode 100644 index 0000000000..299691a619

board/freescale/imx8mm_evk/Kconfig new file +6 -0
@@ -0,0 +1,12 @@
+if TARGET_IMX8MM_EVK
+
+config SYS_BOARD
+	default "imx8mm_evk"
+
+config SYS_VENDOR
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
board/freescale/imx8mm_evk/Kconfig new file +6 -0
+	default "freescale"
+
+config SYS_CONFIG_NAME
+	default "imx8mm_evk"
+
+endif
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/MAINTAINERS new file mode

100644

Quoted 22 lines
Quoted 22 lines
Quoted 22 lines
Quoted 22 lines
Quoted 22 lines

index 0000000000..b031bb0674

board/freescale/imx8mm_evk/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@
+i.MX8MM EVK BOARD
+M:	Peng Fan <[email protected]>
+S:	Maintained
+F:	board/freescale/imx8mm_evk/
+F:	include/configs/imx8mm_evk.h
+F:	configs/imx8mm_evk_defconfig
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/Makefile new file mode 100644 index 0000000000..1db7b62caf

board/freescale/imx8mm_evk/Makefile new file +6 -0
@@ -0,0 +1,12 @@
+#
+# Copyright 2018 NXP
+#
+# SPDX-License-Identifier:      GPL-2.0+
+#
+
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
board/freescale/imx8mm_evk/Makefile new file +6 -0
+obj-y += imx8mm_evk.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing.o
+endif
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/imx8mm_evk.c new file mode

100644

Quoted 2,428 lines
Quoted 2,428 lines
Quoted 2,428 lines
Quoted 2,428 lines
Quoted 32 lines

index 0000000000..a681aca04d

board/freescale/imx8mm_evk/imx8mm_evk.c new file +26 -0
@@ -0,0 +1,144 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm-generic/gpio.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <asm/arch/imx8mm_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <asm/arch/clock.h>
+#include <spl.h>
+#include <asm/mach-imx/dma.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL	(PAD_CTL_DSE6 |

PAD_CTL_FSEL1) +#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE) +

board/freescale/imx8mm_evk/imx8mm_evk.c

Quoted 2 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +2 -0
+static iomux_v3_cfg_t const uart_pads[] = {
+	IMX8MM_PAD_UART2_RXD_UART2_RX |  

MUX_PAD_CTRL(UART_PAD_CTRL),

board/freescale/imx8mm_evk/imx8mm_evk.c

Quoted 1 line
board/freescale/imx8mm_evk/imx8mm_evk.c new file +1 -0
+	IMX8MM_PAD_UART2_TXD_UART2_TX |  

MUX_PAD_CTRL(UART_PAD_CTRL),

Quoted 34 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +4 -0
+};
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	IMX8MM_PAD_GPIO1_IO02_WDOG1_WDOG_B  |

MUX_PAD_CTRL(WDOG_PAD_CTRL), +};

board/freescale/imx8mm_evk/imx8mm_evk.c new file +4 -0
+
+int board_early_init_f(void)
+{
+	struct wdog_regs *wdog = (struct wdog_regs

*)WDOG1_BASE_ADDR; +

board/freescale/imx8mm_evk/imx8mm_evk.c new file +1 -0
+	imx_iomux_v3_setup_multiple_pads(wdog_pads,

ARRAY_SIZE(wdog_pads)); +

board/freescale/imx8mm_evk/imx8mm_evk.c new file +3 -0
+	set_wdog_reset(wdog);
+
+	imx_iomux_v3_setup_multiple_pads(uart_pads,

ARRAY_SIZE(uart_pads)); +

board/freescale/imx8mm_evk/imx8mm_evk.c new file +14 -0
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_POSTCLK_INIT
+int board_postclk_init(void)
+{
+	/* TODO */
+	return 0;
+}
+#endif
+
+int dram_init(void)
+{
+	/* rom_pointer[1] contains the size of TEE

occupies */

board/freescale/imx8mm_evk/imx8mm_evk.c new file +2 -0
+	if (rom_pointer[1])
+		gd->ram_size = PHYS_SDRAM_SIZE -

rom_pointer[1];

board/freescale/imx8mm_evk/imx8mm_evk.c

Quoted 8 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +8 -0
+	else
+		gd->ram_size = PHYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, bd_t *bd)  
	^^^ - fdt_board_setup ?  

board/freescale/imx8mm_evk/imx8mm_evk.c

Quoted 9 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +9 -0
+{
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+#define FEC_RST_PAD IMX_GPIO_NR(4, 22)
+static iomux_v3_cfg_t const fec1_rst_pads[] = {
+	IMX8MM_PAD_SAI2_RXC_GPIO4_IO22 |  

MUX_PAD_CTRL(NO_PAD_CTRL),

This shall be done with fsl_fec.c DM driver - there is support for adding reset pin (to dts).

board/freescale/imx8mm_evk/imx8mm_evk.c

Quoted 12 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +6 -0
+};
+
+static void setup_iomux_fec(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec1_rst_pads,
+

ARRAY_SIZE(fec1_rst_pads)); +

board/freescale/imx8mm_evk/imx8mm_evk.c new file +5 -0
+	gpio_request(FEC_RST_PAD, "fec1_rst");
+	gpio_direction_output(FEC_RST_PAD, 0);
+	udelay(500);
+	gpio_direction_output(FEC_RST_PAD, 1);
+}  

This shall be replaced with DM/DTS of the fsl_fec.c driver. Please also note that there are (at least on imx6q) some timing issues when we move the code to DM/DTS (some delay is needed).

Quoted 22 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +4 -0
+
+static int setup_fec(void)
+{
+	struct iomuxc_gpr_base_regs *const

iomuxc_gpr_regs

board/freescale/imx8mm_evk/imx8mm_evk.c new file +1 -0
+		= (struct iomuxc_gpr_base_regs

*)IOMUXC_GPR_BASE_ADDR; +

board/freescale/imx8mm_evk/imx8mm_evk.c new file +3 -0
+	setup_iomux_fec();
+
+	/* Use 125M anatop REF_CLK1 for ENET1, not from

external */

board/freescale/imx8mm_evk/imx8mm_evk.c new file +2 -0
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+

IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_SHIFT, 0);

board/freescale/imx8mm_evk/imx8mm_evk.c new file +6 -0
+	return set_clk_enet(ENET_125MHZ);
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/* enable rgmii rxc skew and phy mode select to

RGMII copper */

board/freescale/imx8mm_evk/imx8mm_evk.c new file +1 -0
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);

board/freescale/imx8mm_evk/imx8mm_evk.c

Quoted 10 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +10 -0
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+	return 0;  

Which PHY do you use? E.g. KSZ... support passing those values via DTS.

Quoted 30 lines
board/freescale/imx8mm_evk/imx8mm_evk.c new file +24 -0
+}
+#endif
+
+int board_init(void)
+{
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+	return 0;
+}
+
+int board_mmc_get_env_dev(int devno)
+{
+	return devno - 1;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	env_set("board_name", "EVK");
+	env_set("board_rev", "iMX8MM");
+#endif
+	return 0;
+}
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/lpddr4_timing.c new file mode 100644 index 0000000000..4bade5bf74

board/freescale/imx8mm_evk/lpddr4_timing.c line 3

Quoted 3 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +3 -0
@@ -0,0 +1,1980 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP  

Author is missing.

Quoted 307 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +114 -0
+ */
+
+#include <linux/kernel.h>
+#include <common.h>
+#include <asm/arch/ddr.h>
+#include <asm/arch/lpddr4_define.h>
+
+struct dram_cfg_param lpddr4_ddrc_cfg[] = {
+	/* Start to config, default 3200mbps */
+	{ DDRC_DBG1(0),	0x00000001 },
+	{ DDRC_PWRCTL(0), 0x00000001 },
+	{ DDRC_MSTR(0),	0xa1080020 },
+	{ DDRC_RFSHTMG(0), 0x005b00d2 },
+	{ DDRC_INIT0(0), 0xC003061B },
+	{ DDRC_INIT1(0), 0x009D0000 },
+	{ DDRC_INIT3(0), 0x00D4002D },
+	{ DDRC_INIT4(0), (LPDDR4_MR3 << 16) | 0x0000 },
+	{ DDRC_INIT6(0), 0x0066004a },
+	{ DDRC_INIT7(0), 0x0006004a },
+
+	{ DDRC_DRAMTMG0(0), 0x1A201B22 },
+	{ DDRC_DRAMTMG1(0), 0x00060633 },
+	{ DDRC_DRAMTMG3(0), 0x00C0C000 },
+	{ DDRC_DRAMTMG4(0), 0x0F04080F },
+	{ DDRC_DRAMTMG5(0), 0x02040C0C },
+	{ DDRC_DRAMTMG6(0), 0x01010007 },
+	{ DDRC_DRAMTMG7(0), 0x00000401 },
+	{ DDRC_DRAMTMG12(0), 0x00020600 },
+	{ DDRC_DRAMTMG13(0), 0x0C100002 },
+	{ DDRC_DRAMTMG14(0), 0x000000E6 },
+	{ DDRC_DRAMTMG17(0), 0x00A00050 },
+
+	{ DDRC_ZQCTL0(0), 0x03200018 },
+	{ DDRC_ZQCTL1(0), 0x028061A8 },
+	{ DDRC_ZQCTL2(0), 0x00000000 },
+
+	{ DDRC_DFITMG0(0), 0x0497820A },
+	{ DDRC_DFITMG2(0), 0x0000170A },
+	{ DDRC_DRAMTMG2(0), 0x070E171a },
+	{ DDRC_DBICTL(0), 0x00000001 },
+
+	{ DDRC_DFITMG1(0), 0x00080303 },
+	{ DDRC_DFIUPD0(0), 0xE0400018 },
+	{ DDRC_DFIUPD1(0), 0x00DF00E4 },
+	{ DDRC_DFIUPD2(0), 0x80000000 },
+	{ DDRC_DFIMISC(0), 0x00000011 },
+
+	{ DDRC_DFIPHYMSTR(0), 0x00000000 },
+	{ DDRC_RANKCTL(0), 0x00000c99 },
+
+	/* address mapping */
+	{ DDRC_ADDRMAP0(0), 0x0000001f },
+	{ DDRC_ADDRMAP1(0), 0x00080808 },
+	{ DDRC_ADDRMAP2(0), 0x00000000 },
+	{ DDRC_ADDRMAP3(0), 0x00000000 },
+	{ DDRC_ADDRMAP4(0), 0x00001f1f },
+	{ DDRC_ADDRMAP5(0), 0x07070707 },
+	{ DDRC_ADDRMAP6(0), 0x07070707 },
+	{ DDRC_ADDRMAP7(0), 0x00000f0f },
+
+	/* performance setting */
+	{ DDRC_SCHED(0), 0x29001701 },
+	{ DDRC_SCHED1(0), 0x0000002c },
+	{ DDRC_PERFHPR1(0), 0x04000030 },
+	{ DDRC_PERFLPR1(0), 0x900093e7 },
+	{ DDRC_PERFWR1(0), 0x20005574 },
+	{ DDRC_PCCFG(0), 0x00000111 },
+	{ DDRC_PCFGW_0(0), 0x000072ff },
+	{ DDRC_PCFGQOS0_0(0), 0x02100e07 },
+	{ DDRC_PCFGQOS1_0(0), 0x00620096 },
+	{ DDRC_PCFGWQOS0_0(0), 0x01100e07 },
+	{ DDRC_PCFGWQOS1_0(0), 0x00c8012c },
+
+	/* frequency P1&P2 */
+	/* Frequency 1: 400mbps */
+	{ DDRC_FREQ1_DRAMTMG0(0), 0x0d0b010c },
+	{ DDRC_FREQ1_DRAMTMG1(0), 0x00030410 },
+	{ DDRC_FREQ1_DRAMTMG2(0), 0x0203090c },
+	{ DDRC_FREQ1_DRAMTMG3(0), 0x00505006 },
+	{ DDRC_FREQ1_DRAMTMG4(0), 0x05040305 },
+	{ DDRC_FREQ1_DRAMTMG5(0), 0x0d0e0504 },
+	{ DDRC_FREQ1_DRAMTMG6(0), 0x0a060004 },
+	{ DDRC_FREQ1_DRAMTMG7(0), 0x0000090e },
+	{ DDRC_FREQ1_DRAMTMG14(0), 0x00000032 },
+	{ DDRC_FREQ1_DRAMTMG15(0), 0x00000000 },
+	{ DDRC_FREQ1_DRAMTMG17(0), 0x0036001b },
+	{ DDRC_FREQ1_DERATEINT(0), 0x7e9fbeb1 },
+	{ DDRC_FREQ1_DFITMG0(0), 0x03818200 },
+	{ DDRC_FREQ1_DFITMG2(0), 0x00000000 },
+	{ DDRC_FREQ1_RFSHTMG(0), 0x000C001c },
+	{ DDRC_FREQ1_INIT3(0), 0x00840000 },
+	{ DDRC_FREQ1_INIT4(0), 0x00310000 },
+	{ DDRC_FREQ1_INIT6(0), 0x0066004a },
+	{ DDRC_FREQ1_INIT7(0), 0x0006004a },
+
+	/* Frequency 2: 100mbps */
+	{ DDRC_FREQ2_DRAMTMG0(0), 0x0d0b010c },
+	{ DDRC_FREQ2_DRAMTMG1(0), 0x00030410 },
+	{ DDRC_FREQ2_DRAMTMG2(0), 0x0203090c },
+	{ DDRC_FREQ2_DRAMTMG3(0), 0x00505006 },
+	{ DDRC_FREQ2_DRAMTMG4(0), 0x05040305 },
+	{ DDRC_FREQ2_DRAMTMG5(0), 0x0d0e0504 },
+	{ DDRC_FREQ2_DRAMTMG6(0), 0x0a060004 },
+	{ DDRC_FREQ2_DRAMTMG7(0), 0x0000090e },
+	{ DDRC_FREQ2_DRAMTMG14(0), 0x00000032 },
+	{ DDRC_FREQ2_DRAMTMG17(0), 0x0036001b },
+	{ DDRC_FREQ2_DERATEINT(0), 0x7e9fbeb1 },
+	{ DDRC_FREQ2_DFITMG0(0), 0x03818200 },
+	{ DDRC_FREQ2_DFITMG2(0), 0x00000000 },
+	{ DDRC_FREQ2_RFSHTMG(0), 0x0003800c },
+	{ DDRC_FREQ2_RFSHTMG(0), 0x00030007 },
+	{ DDRC_FREQ2_INIT3(0), 0x00840000 },
+	{ DDRC_FREQ2_INIT4(0), 0x00310008 },
+	{ DDRC_FREQ2_INIT4(0), (LPDDR4_MR3 << 16) |

0x0000 },

board/freescale/imx8mm_evk/lpddr4_timing.c new file +192 -0
+	{ DDRC_FREQ2_INIT6(0), 0x0066004a },
+	{ DDRC_FREQ2_INIT7(0), 0x0006004a },
+
+	/* boot start point */
+	{ DDRC_MSTR2(0), 0x2 }, //DDRC_MSTR2
+};
+
+/* PHY Initialize Configuration */
+struct dram_cfg_param lpddr4_ddrphy_cfg[] = {
+	{ 0x1005f, 0x1ff },
+	{ 0x1015f, 0x1ff },
+	{ 0x1105f, 0x1ff },
+	{ 0x1115f, 0x1ff },
+	{ 0x1205f, 0x1ff },
+	{ 0x1215f, 0x1ff },
+	{ 0x1305f, 0x1ff },
+	{ 0x1315f, 0x1ff },
+
+	{ 0x11005f, 0x1ff },
+	{ 0x11015f, 0x1ff },
+	{ 0x11105f, 0x1ff },
+	{ 0x11115f, 0x1ff },
+	{ 0x11205f, 0x1ff },
+	{ 0x11215f, 0x1ff },
+	{ 0x11305f, 0x1ff },
+	{ 0x11315f, 0x1ff },
+
+	{ 0x21005f, 0x1ff },
+	{ 0x21015f, 0x1ff },
+	{ 0x21105f, 0x1ff },
+	{ 0x21115f, 0x1ff },
+	{ 0x21205f, 0x1ff },
+	{ 0x21215f, 0x1ff },
+	{ 0x21305f, 0x1ff },
+	{ 0x21315f, 0x1ff },
+
+	{ 0x55, 0x1ff },
+	{ 0x1055, 0x1ff },
+	{ 0x2055, 0x1ff },
+	{ 0x3055, 0x1ff },
+	{ 0x4055, 0x1ff },
+	{ 0x5055, 0x1ff },
+	{ 0x6055, 0x1ff },
+	{ 0x7055, 0x1ff },
+	{ 0x8055, 0x1ff },
+	{ 0x9055, 0x1ff },
+
+	{ 0x200c5, 0x19 },
+	{ 0x1200c5, 0x7 },
+	{ 0x2200c5, 0x7 },
+
+	{ 0x2002e, 0x2 },
+	{ 0x12002e, 0x2 },
+	{ 0x22002e, 0x2 },
+
+	{ 0x90204, 0x0 },
+	{ 0x190204, 0x0 },
+	{ 0x290204, 0x0 },
+
+	{ 0x20024, 0xab },
+	{ 0x2003a, 0x0 },
+
+	{ 0x120024, 0xab },
+	{ 0x2003a, 0x0 },
+
+	{ 0x220024, 0xab },
+	{ 0x2003a, 0x0 },
+
+	{ 0x20056, 0x3 },
+	{ 0x120056, 0xa },
+	{ 0x220056, 0xa },
+
+	{ 0x1004d, 0xe00 },
+	{ 0x1014d, 0xe00 },
+	{ 0x1104d, 0xe00 },
+	{ 0x1114d, 0xe00 },
+	{ 0x1204d, 0xe00 },
+	{ 0x1214d, 0xe00 },
+	{ 0x1304d, 0xe00 },
+	{ 0x1314d, 0xe00 },
+
+	{ 0x11004d, 0xe00 },
+	{ 0x11014d, 0xe00 },
+	{ 0x11104d, 0xe00 },
+	{ 0x11114d, 0xe00 },
+	{ 0x11204d, 0xe00 },
+	{ 0x11214d, 0xe00 },
+	{ 0x11304d, 0xe00 },
+	{ 0x11314d, 0xe00 },
+
+	{ 0x21004d, 0xe00 },
+	{ 0x21014d, 0xe00 },
+	{ 0x21104d, 0xe00 },
+	{ 0x21114d, 0xe00 },
+	{ 0x21204d, 0xe00 },
+	{ 0x21214d, 0xe00 },
+	{ 0x21304d, 0xe00 },
+	{ 0x21314d, 0xe00 },
+
+	{ 0x10049, 0xfbe },
+	{ 0x10149, 0xfbe },
+	{ 0x11049, 0xfbe },
+	{ 0x11149, 0xfbe },
+	{ 0x12049, 0xfbe },
+	{ 0x12149, 0xfbe },
+	{ 0x13049, 0xfbe },
+	{ 0x13149, 0xfbe },
+
+	{ 0x110049, 0xfbe },
+	{ 0x110149, 0xfbe },
+	{ 0x111049, 0xfbe },
+	{ 0x111149, 0xfbe },
+	{ 0x112049, 0xfbe },
+	{ 0x112149, 0xfbe },
+	{ 0x113049, 0xfbe },
+	{ 0x113149, 0xfbe },
+
+	{ 0x210049, 0xfbe },
+	{ 0x210149, 0xfbe },
+	{ 0x211049, 0xfbe },
+	{ 0x211149, 0xfbe },
+	{ 0x212049, 0xfbe },
+	{ 0x212149, 0xfbe },
+	{ 0x213049, 0xfbe },
+	{ 0x213149, 0xfbe },
+
+	{ 0x43, 0x63 },
+	{ 0x1043, 0x63 },
+	{ 0x2043, 0x63 },
+	{ 0x3043, 0x63 },
+	{ 0x4043, 0x63 },
+	{ 0x5043, 0x63 },
+	{ 0x6043, 0x63 },
+	{ 0x7043, 0x63 },
+	{ 0x8043, 0x63 },
+	{ 0x9043, 0x63 },
+
+	{ 0x20018, 0x3 },
+	{ 0x20075, 0x4 },
+	{ 0x20050, 0x0 },
+	{ 0x20008, 0x2ee },
+	{ 0x120008, 0x64 },
+	{ 0x220008, 0x19 },
+	{ 0x20088, 0x9 },
+
+	{ 0x200b2, 0x1d4 },
+	{ 0x10043, 0x5a1 },
+	{ 0x10143, 0x5a1 },
+	{ 0x11043, 0x5a1 },
+	{ 0x11143, 0x5a1 },
+	{ 0x12043, 0x5a1 },
+	{ 0x12143, 0x5a1 },
+	{ 0x13043, 0x5a1 },
+	{ 0x13143, 0x5a1 },
+
+	{ 0x1200b2, 0xdc },
+	{ 0x110043, 0x5a1 },
+	{ 0x110143, 0x5a1 },
+	{ 0x111043, 0x5a1 },
+	{ 0x111143, 0x5a1 },
+	{ 0x112043, 0x5a1 },
+	{ 0x112143, 0x5a1 },
+	{ 0x113043, 0x5a1 },
+	{ 0x113143, 0x5a1 },
+
+	{ 0x2200b2, 0xdc },
+	{ 0x210043, 0x5a1 },
+	{ 0x210143, 0x5a1 },
+	{ 0x211043, 0x5a1 },
+	{ 0x211143, 0x5a1 },
+	{ 0x212043, 0x5a1 },
+	{ 0x212143, 0x5a1 },
+	{ 0x213043, 0x5a1 },
+	{ 0x213143, 0x5a1 },
+
+	{ 0x200fa, 0x1 },
+	{ 0x1200fa, 0x1 },
+	{ 0x2200fa, 0x1 },
+
+	{ 0x20019, 0x1 },
+	{ 0x120019, 0x1 },
+	{ 0x220019, 0x1 },
+
+	{ 0x200f0, 0x660 },
+	{ 0x200f1, 0x0 },
+	{ 0x200f2, 0x4444 },
+	{ 0x200f3, 0x8888 },
+	{ 0x200f4, 0x5665 },
+	{ 0x200f5, 0x0 },
+	{ 0x200f6, 0x0 },
+	{ 0x200f7, 0xf000 },
+

board/freescale/imx8mm_evk/lpddr4_timing.c

Quoted 10 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +10 -0
+	{ 0x20025, 0x0 },
+	{ 0x2002d, LPDDR4_PHY_DMIPinPresent },
+	{ 0x12002d, LPDDR4_PHY_DMIPinPresent },
+	{ 0x22002d, LPDDR4_PHY_DMIPinPresent },
+	{ 0x200c7, 0x21 },
+	{ 0x200ca, 0x24 },
+	{ 0x1200c7, 0x21 },
+	{ 0x1200ca, 0x24 },
+	{ 0x2200c7, 0x21 },
+	{ 0x2200ca, 0x24 },  

Why do you add tuple - offset and value? Shouldn't we have the DDR training functions here?

It is possible to train IMX6Q and Vybrid's DDR3 (as fair as I know). Would it be also possible to add the DDR4 training code for IMX8?

Quoted 714 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +714 -0
+};
+
+/* ddr phy trained csr */
+struct dram_cfg_param lpddr4_ddrphy_trained_csr[] = {
+	{ 0x200b2, 0x0 },
+	{ 0x1200b2, 0x0 },
+	{ 0x2200b2, 0x0 },
+	{ 0x200cb, 0x0 },
+	{ 0x10043, 0x0 },
+	{ 0x110043, 0x0 },
+	{ 0x210043, 0x0 },
+	{ 0x10143, 0x0 },
+	{ 0x110143, 0x0 },
+	{ 0x210143, 0x0 },
+	{ 0x11043, 0x0 },
+	{ 0x111043, 0x0 },
+	{ 0x211043, 0x0 },
+	{ 0x11143, 0x0 },
+	{ 0x111143, 0x0 },
+	{ 0x211143, 0x0 },
+	{ 0x12043, 0x0 },
+	{ 0x112043, 0x0 },
+	{ 0x212043, 0x0 },
+	{ 0x12143, 0x0 },
+	{ 0x112143, 0x0 },
+	{ 0x212143, 0x0 },
+	{ 0x13043, 0x0 },
+	{ 0x113043, 0x0 },
+	{ 0x213043, 0x0 },
+	{ 0x13143, 0x0 },
+	{ 0x113143, 0x0 },
+	{ 0x213143, 0x0 },
+	{ 0x80, 0x0 },
+	{ 0x100080, 0x0 },
+	{ 0x200080, 0x0 },
+	{ 0x1080, 0x0 },
+	{ 0x101080, 0x0 },
+	{ 0x201080, 0x0 },
+	{ 0x2080, 0x0 },
+	{ 0x102080, 0x0 },
+	{ 0x202080, 0x0 },
+	{ 0x3080, 0x0 },
+	{ 0x103080, 0x0 },
+	{ 0x203080, 0x0 },
+	{ 0x4080, 0x0 },
+	{ 0x104080, 0x0 },
+	{ 0x204080, 0x0 },
+	{ 0x5080, 0x0 },
+	{ 0x105080, 0x0 },
+	{ 0x205080, 0x0 },
+	{ 0x6080, 0x0 },
+	{ 0x106080, 0x0 },
+	{ 0x206080, 0x0 },
+	{ 0x7080, 0x0 },
+	{ 0x107080, 0x0 },
+	{ 0x207080, 0x0 },
+	{ 0x8080, 0x0 },
+	{ 0x108080, 0x0 },
+	{ 0x208080, 0x0 },
+	{ 0x9080, 0x0 },
+	{ 0x109080, 0x0 },
+	{ 0x209080, 0x0 },
+	{ 0x10080, 0x0 },
+	{ 0x110080, 0x0 },
+	{ 0x210080, 0x0 },
+	{ 0x10180, 0x0 },
+	{ 0x110180, 0x0 },
+	{ 0x210180, 0x0 },
+	{ 0x11080, 0x0 },
+	{ 0x111080, 0x0 },
+	{ 0x211080, 0x0 },
+	{ 0x11180, 0x0 },
+	{ 0x111180, 0x0 },
+	{ 0x211180, 0x0 },
+	{ 0x12080, 0x0 },
+	{ 0x112080, 0x0 },
+	{ 0x212080, 0x0 },
+	{ 0x12180, 0x0 },
+	{ 0x112180, 0x0 },
+	{ 0x212180, 0x0 },
+	{ 0x13080, 0x0 },
+	{ 0x113080, 0x0 },
+	{ 0x213080, 0x0 },
+	{ 0x13180, 0x0 },
+	{ 0x113180, 0x0 },
+	{ 0x213180, 0x0 },
+	{ 0x10081, 0x0 },
+	{ 0x110081, 0x0 },
+	{ 0x210081, 0x0 },
+	{ 0x10181, 0x0 },
+	{ 0x110181, 0x0 },
+	{ 0x210181, 0x0 },
+	{ 0x11081, 0x0 },
+	{ 0x111081, 0x0 },
+	{ 0x211081, 0x0 },
+	{ 0x11181, 0x0 },
+	{ 0x111181, 0x0 },
+	{ 0x211181, 0x0 },
+	{ 0x12081, 0x0 },
+	{ 0x112081, 0x0 },
+	{ 0x212081, 0x0 },
+	{ 0x12181, 0x0 },
+	{ 0x112181, 0x0 },
+	{ 0x212181, 0x0 },
+	{ 0x13081, 0x0 },
+	{ 0x113081, 0x0 },
+	{ 0x213081, 0x0 },
+	{ 0x13181, 0x0 },
+	{ 0x113181, 0x0 },
+	{ 0x213181, 0x0 },
+	{ 0x100d0, 0x0 },
+	{ 0x1100d0, 0x0 },
+	{ 0x2100d0, 0x0 },
+	{ 0x101d0, 0x0 },
+	{ 0x1101d0, 0x0 },
+	{ 0x2101d0, 0x0 },
+	{ 0x110d0, 0x0 },
+	{ 0x1110d0, 0x0 },
+	{ 0x2110d0, 0x0 },
+	{ 0x111d0, 0x0 },
+	{ 0x1111d0, 0x0 },
+	{ 0x2111d0, 0x0 },
+	{ 0x120d0, 0x0 },
+	{ 0x1120d0, 0x0 },
+	{ 0x2120d0, 0x0 },
+	{ 0x121d0, 0x0 },
+	{ 0x1121d0, 0x0 },
+	{ 0x2121d0, 0x0 },
+	{ 0x130d0, 0x0 },
+	{ 0x1130d0, 0x0 },
+	{ 0x2130d0, 0x0 },
+	{ 0x131d0, 0x0 },
+	{ 0x1131d0, 0x0 },
+	{ 0x2131d0, 0x0 },
+	{ 0x100d1, 0x0 },
+	{ 0x1100d1, 0x0 },
+	{ 0x2100d1, 0x0 },
+	{ 0x101d1, 0x0 },
+	{ 0x1101d1, 0x0 },
+	{ 0x2101d1, 0x0 },
+	{ 0x110d1, 0x0 },
+	{ 0x1110d1, 0x0 },
+	{ 0x2110d1, 0x0 },
+	{ 0x111d1, 0x0 },
+	{ 0x1111d1, 0x0 },
+	{ 0x2111d1, 0x0 },
+	{ 0x120d1, 0x0 },
+	{ 0x1120d1, 0x0 },
+	{ 0x2120d1, 0x0 },
+	{ 0x121d1, 0x0 },
+	{ 0x1121d1, 0x0 },
+	{ 0x2121d1, 0x0 },
+	{ 0x130d1, 0x0 },
+	{ 0x1130d1, 0x0 },
+	{ 0x2130d1, 0x0 },
+	{ 0x131d1, 0x0 },
+	{ 0x1131d1, 0x0 },
+	{ 0x2131d1, 0x0 },
+	{ 0x10068, 0x0 },
+	{ 0x10168, 0x0 },
+	{ 0x10268, 0x0 },
+	{ 0x10368, 0x0 },
+	{ 0x10468, 0x0 },
+	{ 0x10568, 0x0 },
+	{ 0x10668, 0x0 },
+	{ 0x10768, 0x0 },
+	{ 0x10868, 0x0 },
+	{ 0x11068, 0x0 },
+	{ 0x11168, 0x0 },
+	{ 0x11268, 0x0 },
+	{ 0x11368, 0x0 },
+	{ 0x11468, 0x0 },
+	{ 0x11568, 0x0 },
+	{ 0x11668, 0x0 },
+	{ 0x11768, 0x0 },
+	{ 0x11868, 0x0 },
+	{ 0x12068, 0x0 },
+	{ 0x12168, 0x0 },
+	{ 0x12268, 0x0 },
+	{ 0x12368, 0x0 },
+	{ 0x12468, 0x0 },
+	{ 0x12568, 0x0 },
+	{ 0x12668, 0x0 },
+	{ 0x12768, 0x0 },
+	{ 0x12868, 0x0 },
+	{ 0x13068, 0x0 },
+	{ 0x13168, 0x0 },
+	{ 0x13268, 0x0 },
+	{ 0x13368, 0x0 },
+	{ 0x13468, 0x0 },
+	{ 0x13568, 0x0 },
+	{ 0x13668, 0x0 },
+	{ 0x13768, 0x0 },
+	{ 0x13868, 0x0 },
+	{ 0x10069, 0x0 },
+	{ 0x10169, 0x0 },
+	{ 0x10269, 0x0 },
+	{ 0x10369, 0x0 },
+	{ 0x10469, 0x0 },
+	{ 0x10569, 0x0 },
+	{ 0x10669, 0x0 },
+	{ 0x10769, 0x0 },
+	{ 0x10869, 0x0 },
+	{ 0x11069, 0x0 },
+	{ 0x11169, 0x0 },
+	{ 0x11269, 0x0 },
+	{ 0x11369, 0x0 },
+	{ 0x11469, 0x0 },
+	{ 0x11569, 0x0 },
+	{ 0x11669, 0x0 },
+	{ 0x11769, 0x0 },
+	{ 0x11869, 0x0 },
+	{ 0x12069, 0x0 },
+	{ 0x12169, 0x0 },
+	{ 0x12269, 0x0 },
+	{ 0x12369, 0x0 },
+	{ 0x12469, 0x0 },
+	{ 0x12569, 0x0 },
+	{ 0x12669, 0x0 },
+	{ 0x12769, 0x0 },
+	{ 0x12869, 0x0 },
+	{ 0x13069, 0x0 },
+	{ 0x13169, 0x0 },
+	{ 0x13269, 0x0 },
+	{ 0x13369, 0x0 },
+	{ 0x13469, 0x0 },
+	{ 0x13569, 0x0 },
+	{ 0x13669, 0x0 },
+	{ 0x13769, 0x0 },
+	{ 0x13869, 0x0 },
+	{ 0x1008c, 0x0 },
+	{ 0x11008c, 0x0 },
+	{ 0x21008c, 0x0 },
+	{ 0x1018c, 0x0 },
+	{ 0x11018c, 0x0 },
+	{ 0x21018c, 0x0 },
+	{ 0x1108c, 0x0 },
+	{ 0x11108c, 0x0 },
+	{ 0x21108c, 0x0 },
+	{ 0x1118c, 0x0 },
+	{ 0x11118c, 0x0 },
+	{ 0x21118c, 0x0 },
+	{ 0x1208c, 0x0 },
+	{ 0x11208c, 0x0 },
+	{ 0x21208c, 0x0 },
+	{ 0x1218c, 0x0 },
+	{ 0x11218c, 0x0 },
+	{ 0x21218c, 0x0 },
+	{ 0x1308c, 0x0 },
+	{ 0x11308c, 0x0 },
+	{ 0x21308c, 0x0 },
+	{ 0x1318c, 0x0 },
+	{ 0x11318c, 0x0 },
+	{ 0x21318c, 0x0 },
+	{ 0x1008d, 0x0 },
+	{ 0x11008d, 0x0 },
+	{ 0x21008d, 0x0 },
+	{ 0x1018d, 0x0 },
+	{ 0x11018d, 0x0 },
+	{ 0x21018d, 0x0 },
+	{ 0x1108d, 0x0 },
+	{ 0x11108d, 0x0 },
+	{ 0x21108d, 0x0 },
+	{ 0x1118d, 0x0 },
+	{ 0x11118d, 0x0 },
+	{ 0x21118d, 0x0 },
+	{ 0x1208d, 0x0 },
+	{ 0x11208d, 0x0 },
+	{ 0x21208d, 0x0 },
+	{ 0x1218d, 0x0 },
+	{ 0x11218d, 0x0 },
+	{ 0x21218d, 0x0 },
+	{ 0x1308d, 0x0 },
+	{ 0x11308d, 0x0 },
+	{ 0x21308d, 0x0 },
+	{ 0x1318d, 0x0 },
+	{ 0x11318d, 0x0 },
+	{ 0x21318d, 0x0 },
+	{ 0x100c0, 0x0 },
+	{ 0x1100c0, 0x0 },
+	{ 0x2100c0, 0x0 },
+	{ 0x101c0, 0x0 },
+	{ 0x1101c0, 0x0 },
+	{ 0x2101c0, 0x0 },
+	{ 0x102c0, 0x0 },
+	{ 0x1102c0, 0x0 },
+	{ 0x2102c0, 0x0 },
+	{ 0x103c0, 0x0 },
+	{ 0x1103c0, 0x0 },
+	{ 0x2103c0, 0x0 },
+	{ 0x104c0, 0x0 },
+	{ 0x1104c0, 0x0 },
+	{ 0x2104c0, 0x0 },
+	{ 0x105c0, 0x0 },
+	{ 0x1105c0, 0x0 },
+	{ 0x2105c0, 0x0 },
+	{ 0x106c0, 0x0 },
+	{ 0x1106c0, 0x0 },
+	{ 0x2106c0, 0x0 },
+	{ 0x107c0, 0x0 },
+	{ 0x1107c0, 0x0 },
+	{ 0x2107c0, 0x0 },
+	{ 0x108c0, 0x0 },
+	{ 0x1108c0, 0x0 },
+	{ 0x2108c0, 0x0 },
+	{ 0x110c0, 0x0 },
+	{ 0x1110c0, 0x0 },
+	{ 0x2110c0, 0x0 },
+	{ 0x111c0, 0x0 },
+	{ 0x1111c0, 0x0 },
+	{ 0x2111c0, 0x0 },
+	{ 0x112c0, 0x0 },
+	{ 0x1112c0, 0x0 },
+	{ 0x2112c0, 0x0 },
+	{ 0x113c0, 0x0 },
+	{ 0x1113c0, 0x0 },
+	{ 0x2113c0, 0x0 },
+	{ 0x114c0, 0x0 },
+	{ 0x1114c0, 0x0 },
+	{ 0x2114c0, 0x0 },
+	{ 0x115c0, 0x0 },
+	{ 0x1115c0, 0x0 },
+	{ 0x2115c0, 0x0 },
+	{ 0x116c0, 0x0 },
+	{ 0x1116c0, 0x0 },
+	{ 0x2116c0, 0x0 },
+	{ 0x117c0, 0x0 },
+	{ 0x1117c0, 0x0 },
+	{ 0x2117c0, 0x0 },
+	{ 0x118c0, 0x0 },
+	{ 0x1118c0, 0x0 },
+	{ 0x2118c0, 0x0 },
+	{ 0x120c0, 0x0 },
+	{ 0x1120c0, 0x0 },
+	{ 0x2120c0, 0x0 },
+	{ 0x121c0, 0x0 },
+	{ 0x1121c0, 0x0 },
+	{ 0x2121c0, 0x0 },
+	{ 0x122c0, 0x0 },
+	{ 0x1122c0, 0x0 },
+	{ 0x2122c0, 0x0 },
+	{ 0x123c0, 0x0 },
+	{ 0x1123c0, 0x0 },
+	{ 0x2123c0, 0x0 },
+	{ 0x124c0, 0x0 },
+	{ 0x1124c0, 0x0 },
+	{ 0x2124c0, 0x0 },
+	{ 0x125c0, 0x0 },
+	{ 0x1125c0, 0x0 },
+	{ 0x2125c0, 0x0 },
+	{ 0x126c0, 0x0 },
+	{ 0x1126c0, 0x0 },
+	{ 0x2126c0, 0x0 },
+	{ 0x127c0, 0x0 },
+	{ 0x1127c0, 0x0 },
+	{ 0x2127c0, 0x0 },
+	{ 0x128c0, 0x0 },
+	{ 0x1128c0, 0x0 },
+	{ 0x2128c0, 0x0 },
+	{ 0x130c0, 0x0 },
+	{ 0x1130c0, 0x0 },
+	{ 0x2130c0, 0x0 },
+	{ 0x131c0, 0x0 },
+	{ 0x1131c0, 0x0 },
+	{ 0x2131c0, 0x0 },
+	{ 0x132c0, 0x0 },
+	{ 0x1132c0, 0x0 },
+	{ 0x2132c0, 0x0 },
+	{ 0x133c0, 0x0 },
+	{ 0x1133c0, 0x0 },
+	{ 0x2133c0, 0x0 },
+	{ 0x134c0, 0x0 },
+	{ 0x1134c0, 0x0 },
+	{ 0x2134c0, 0x0 },
+	{ 0x135c0, 0x0 },
+	{ 0x1135c0, 0x0 },
+	{ 0x2135c0, 0x0 },
+	{ 0x136c0, 0x0 },
+	{ 0x1136c0, 0x0 },
+	{ 0x2136c0, 0x0 },
+	{ 0x137c0, 0x0 },
+	{ 0x1137c0, 0x0 },
+	{ 0x2137c0, 0x0 },
+	{ 0x138c0, 0x0 },
+	{ 0x1138c0, 0x0 },
+	{ 0x2138c0, 0x0 },
+	{ 0x100c1, 0x0 },
+	{ 0x1100c1, 0x0 },
+	{ 0x2100c1, 0x0 },
+	{ 0x101c1, 0x0 },
+	{ 0x1101c1, 0x0 },
+	{ 0x2101c1, 0x0 },
+	{ 0x102c1, 0x0 },
+	{ 0x1102c1, 0x0 },
+	{ 0x2102c1, 0x0 },
+	{ 0x103c1, 0x0 },
+	{ 0x1103c1, 0x0 },
+	{ 0x2103c1, 0x0 },
+	{ 0x104c1, 0x0 },
+	{ 0x1104c1, 0x0 },
+	{ 0x2104c1, 0x0 },
+	{ 0x105c1, 0x0 },
+	{ 0x1105c1, 0x0 },
+	{ 0x2105c1, 0x0 },
+	{ 0x106c1, 0x0 },
+	{ 0x1106c1, 0x0 },
+	{ 0x2106c1, 0x0 },
+	{ 0x107c1, 0x0 },
+	{ 0x1107c1, 0x0 },
+	{ 0x2107c1, 0x0 },
+	{ 0x108c1, 0x0 },
+	{ 0x1108c1, 0x0 },
+	{ 0x2108c1, 0x0 },
+	{ 0x110c1, 0x0 },
+	{ 0x1110c1, 0x0 },
+	{ 0x2110c1, 0x0 },
+	{ 0x111c1, 0x0 },
+	{ 0x1111c1, 0x0 },
+	{ 0x2111c1, 0x0 },
+	{ 0x112c1, 0x0 },
+	{ 0x1112c1, 0x0 },
+	{ 0x2112c1, 0x0 },
+	{ 0x113c1, 0x0 },
+	{ 0x1113c1, 0x0 },
+	{ 0x2113c1, 0x0 },
+	{ 0x114c1, 0x0 },
+	{ 0x1114c1, 0x0 },
+	{ 0x2114c1, 0x0 },
+	{ 0x115c1, 0x0 },
+	{ 0x1115c1, 0x0 },
+	{ 0x2115c1, 0x0 },
+	{ 0x116c1, 0x0 },
+	{ 0x1116c1, 0x0 },
+	{ 0x2116c1, 0x0 },
+	{ 0x117c1, 0x0 },
+	{ 0x1117c1, 0x0 },
+	{ 0x2117c1, 0x0 },
+	{ 0x118c1, 0x0 },
+	{ 0x1118c1, 0x0 },
+	{ 0x2118c1, 0x0 },
+	{ 0x120c1, 0x0 },
+	{ 0x1120c1, 0x0 },
+	{ 0x2120c1, 0x0 },
+	{ 0x121c1, 0x0 },
+	{ 0x1121c1, 0x0 },
+	{ 0x2121c1, 0x0 },
+	{ 0x122c1, 0x0 },
+	{ 0x1122c1, 0x0 },
+	{ 0x2122c1, 0x0 },
+	{ 0x123c1, 0x0 },
+	{ 0x1123c1, 0x0 },
+	{ 0x2123c1, 0x0 },
+	{ 0x124c1, 0x0 },
+	{ 0x1124c1, 0x0 },
+	{ 0x2124c1, 0x0 },
+	{ 0x125c1, 0x0 },
+	{ 0x1125c1, 0x0 },
+	{ 0x2125c1, 0x0 },
+	{ 0x126c1, 0x0 },
+	{ 0x1126c1, 0x0 },
+	{ 0x2126c1, 0x0 },
+	{ 0x127c1, 0x0 },
+	{ 0x1127c1, 0x0 },
+	{ 0x2127c1, 0x0 },
+	{ 0x128c1, 0x0 },
+	{ 0x1128c1, 0x0 },
+	{ 0x2128c1, 0x0 },
+	{ 0x130c1, 0x0 },
+	{ 0x1130c1, 0x0 },
+	{ 0x2130c1, 0x0 },
+	{ 0x131c1, 0x0 },
+	{ 0x1131c1, 0x0 },
+	{ 0x2131c1, 0x0 },
+	{ 0x132c1, 0x0 },
+	{ 0x1132c1, 0x0 },
+	{ 0x2132c1, 0x0 },
+	{ 0x133c1, 0x0 },
+	{ 0x1133c1, 0x0 },
+	{ 0x2133c1, 0x0 },
+	{ 0x134c1, 0x0 },
+	{ 0x1134c1, 0x0 },
+	{ 0x2134c1, 0x0 },
+	{ 0x135c1, 0x0 },
+	{ 0x1135c1, 0x0 },
+	{ 0x2135c1, 0x0 },
+	{ 0x136c1, 0x0 },
+	{ 0x1136c1, 0x0 },
+	{ 0x2136c1, 0x0 },
+	{ 0x137c1, 0x0 },
+	{ 0x1137c1, 0x0 },
+	{ 0x2137c1, 0x0 },
+	{ 0x138c1, 0x0 },
+	{ 0x1138c1, 0x0 },
+	{ 0x2138c1, 0x0 },
+	{ 0x10020, 0x0 },
+	{ 0x110020, 0x0 },
+	{ 0x210020, 0x0 },
+	{ 0x11020, 0x0 },
+	{ 0x111020, 0x0 },
+	{ 0x211020, 0x0 },
+	{ 0x12020, 0x0 },
+	{ 0x112020, 0x0 },
+	{ 0x212020, 0x0 },
+	{ 0x13020, 0x0 },
+	{ 0x113020, 0x0 },
+	{ 0x213020, 0x0 },
+	{ 0x20072, 0x0 },
+	{ 0x20073, 0x0 },
+	{ 0x20074, 0x0 },
+	{ 0x100aa, 0x0 },
+	{ 0x110aa, 0x0 },
+	{ 0x120aa, 0x0 },
+	{ 0x130aa, 0x0 },
+	{ 0x20010, 0x0 },
+	{ 0x120010, 0x0 },
+	{ 0x220010, 0x0 },
+	{ 0x20011, 0x0 },
+	{ 0x120011, 0x0 },
+	{ 0x220011, 0x0 },
+	{ 0x100ae, 0x0 },
+	{ 0x1100ae, 0x0 },
+	{ 0x2100ae, 0x0 },
+	{ 0x100af, 0x0 },
+	{ 0x1100af, 0x0 },
+	{ 0x2100af, 0x0 },
+	{ 0x110ae, 0x0 },
+	{ 0x1110ae, 0x0 },
+	{ 0x2110ae, 0x0 },
+	{ 0x110af, 0x0 },
+	{ 0x1110af, 0x0 },
+	{ 0x2110af, 0x0 },
+	{ 0x120ae, 0x0 },
+	{ 0x1120ae, 0x0 },
+	{ 0x2120ae, 0x0 },
+	{ 0x120af, 0x0 },
+	{ 0x1120af, 0x0 },
+	{ 0x2120af, 0x0 },
+	{ 0x130ae, 0x0 },
+	{ 0x1130ae, 0x0 },
+	{ 0x2130ae, 0x0 },
+	{ 0x130af, 0x0 },
+	{ 0x1130af, 0x0 },
+	{ 0x2130af, 0x0 },
+	{ 0x20020, 0x0 },
+	{ 0x120020, 0x0 },
+	{ 0x220020, 0x0 },
+	{ 0x100a0, 0x0 },
+	{ 0x100a1, 0x0 },
+	{ 0x100a2, 0x0 },
+	{ 0x100a3, 0x0 },
+	{ 0x100a4, 0x0 },
+	{ 0x100a5, 0x0 },
+	{ 0x100a6, 0x0 },
+	{ 0x100a7, 0x0 },
+	{ 0x110a0, 0x0 },
+	{ 0x110a1, 0x0 },
+	{ 0x110a2, 0x0 },
+	{ 0x110a3, 0x0 },
+	{ 0x110a4, 0x0 },
+	{ 0x110a5, 0x0 },
+	{ 0x110a6, 0x0 },
+	{ 0x110a7, 0x0 },
+	{ 0x120a0, 0x0 },
+	{ 0x120a1, 0x0 },
+	{ 0x120a2, 0x0 },
+	{ 0x120a3, 0x0 },
+	{ 0x120a4, 0x0 },
+	{ 0x120a5, 0x0 },
+	{ 0x120a6, 0x0 },
+	{ 0x120a7, 0x0 },
+	{ 0x130a0, 0x0 },
+	{ 0x130a1, 0x0 },
+	{ 0x130a2, 0x0 },
+	{ 0x130a3, 0x0 },
+	{ 0x130a4, 0x0 },
+	{ 0x130a5, 0x0 },
+	{ 0x130a6, 0x0 },
+	{ 0x130a7, 0x0 },
+	{ 0x2007c, 0x0 },
+	{ 0x12007c, 0x0 },
+	{ 0x22007c, 0x0 },
+	{ 0x2007d, 0x0 },
+	{ 0x12007d, 0x0 },
+	{ 0x22007d, 0x0 },
+	{ 0x400fd, 0x0 },
+	{ 0x400c0, 0x0 },
+	{ 0x90201, 0x0 },
+	{ 0x190201, 0x0 },
+	{ 0x290201, 0x0 },
+	{ 0x90202, 0x0 },
+	{ 0x190202, 0x0 },
+	{ 0x290202, 0x0 },
+	{ 0x90203, 0x0 },
+	{ 0x190203, 0x0 },
+	{ 0x290203, 0x0 },
+	{ 0x90204, 0x0 },
+	{ 0x190204, 0x0 },
+	{ 0x290204, 0x0 },
+	{ 0x90205, 0x0 },
+	{ 0x190205, 0x0 },
+	{ 0x290205, 0x0 },
+	{ 0x90206, 0x0 },
+	{ 0x190206, 0x0 },
+	{ 0x290206, 0x0 },
+	{ 0x90207, 0x0 },
+	{ 0x190207, 0x0 },
+	{ 0x290207, 0x0 },
+	{ 0x90208, 0x0 },
+	{ 0x190208, 0x0 },
+	{ 0x290208, 0x0 },
+	{ 0x10062, 0x0 },
+	{ 0x10162, 0x0 },
+	{ 0x10262, 0x0 },
+	{ 0x10362, 0x0 },
+	{ 0x10462, 0x0 },
+	{ 0x10562, 0x0 },
+	{ 0x10662, 0x0 },
+	{ 0x10762, 0x0 },
+	{ 0x10862, 0x0 },
+	{ 0x11062, 0x0 },
+	{ 0x11162, 0x0 },
+	{ 0x11262, 0x0 },
+	{ 0x11362, 0x0 },
+	{ 0x11462, 0x0 },
+	{ 0x11562, 0x0 },
+	{ 0x11662, 0x0 },
+	{ 0x11762, 0x0 },
+	{ 0x11862, 0x0 },
+	{ 0x12062, 0x0 },
+	{ 0x12162, 0x0 },
+	{ 0x12262, 0x0 },
+	{ 0x12362, 0x0 },
+	{ 0x12462, 0x0 },
+	{ 0x12562, 0x0 },
+	{ 0x12662, 0x0 },
+	{ 0x12762, 0x0 },
+	{ 0x12862, 0x0 },
+	{ 0x13062, 0x0 },
+	{ 0x13162, 0x0 },
+	{ 0x13262, 0x0 },
+	{ 0x13362, 0x0 },
+	{ 0x13462, 0x0 },
+	{ 0x13562, 0x0 },
+	{ 0x13662, 0x0 },
+	{ 0x13762, 0x0 },
+	{ 0x13862, 0x0 },
+	{ 0x20077, 0x0 },
+	{ 0x10001, 0x0 },
+	{ 0x11001, 0x0 },
+	{ 0x12001, 0x0 },
+	{ 0x13001, 0x0 },
+	{ 0x10040, 0x0 },
+	{ 0x10140, 0x0 },
+	{ 0x10240, 0x0 },
+	{ 0x10340, 0x0 },
+	{ 0x10440, 0x0 },
+	{ 0x10540, 0x0 },
+	{ 0x10640, 0x0 },
+	{ 0x10740, 0x0 },
+	{ 0x10840, 0x0 },
+	{ 0x10030, 0x0 },
+	{ 0x10130, 0x0 },
+	{ 0x10230, 0x0 },
+	{ 0x10330, 0x0 },
+	{ 0x10430, 0x0 },
+	{ 0x10530, 0x0 },
+	{ 0x10630, 0x0 },
+	{ 0x10730, 0x0 },
+	{ 0x10830, 0x0 },
+	{ 0x11040, 0x0 },
+	{ 0x11140, 0x0 },
+	{ 0x11240, 0x0 },
+	{ 0x11340, 0x0 },
+	{ 0x11440, 0x0 },
+	{ 0x11540, 0x0 },
+	{ 0x11640, 0x0 },
+	{ 0x11740, 0x0 },
+	{ 0x11840, 0x0 },
+	{ 0x11030, 0x0 },
+	{ 0x11130, 0x0 },
+	{ 0x11230, 0x0 },
+	{ 0x11330, 0x0 },
+	{ 0x11430, 0x0 },
+	{ 0x11530, 0x0 },
+	{ 0x11630, 0x0 },
+	{ 0x11730, 0x0 },
+	{ 0x11830, 0x0 },
+	{ 0x12040, 0x0 },
+	{ 0x12140, 0x0 },
+	{ 0x12240, 0x0 },
+	{ 0x12340, 0x0 },
+	{ 0x12440, 0x0 },
+	{ 0x12540, 0x0 },
+	{ 0x12640, 0x0 },
+	{ 0x12740, 0x0 },
+	{ 0x12840, 0x0 },
+	{ 0x12030, 0x0 },
+	{ 0x12130, 0x0 },
+	{ 0x12230, 0x0 },
+	{ 0x12330, 0x0 },
+	{ 0x12430, 0x0 },
+	{ 0x12530, 0x0 },
+	{ 0x12630, 0x0 },
+	{ 0x12730, 0x0 },
+	{ 0x12830, 0x0 },
+	{ 0x13040, 0x0 },
+	{ 0x13140, 0x0 },
+	{ 0x13240, 0x0 },
+	{ 0x13340, 0x0 },
+	{ 0x13440, 0x0 },
+	{ 0x13540, 0x0 },
+	{ 0x13640, 0x0 },
+	{ 0x13740, 0x0 },
+	{ 0x13840, 0x0 },

board/freescale/imx8mm_evk/lpddr4_timing.c

Quoted 10 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +10 -0
+	{ 0x13030, 0x0 },
+	{ 0x13130, 0x0 },
+	{ 0x13230, 0x0 },
+	{ 0x13330, 0x0 },
+	{ 0x13430, 0x0 },
+	{ 0x13530, 0x0 },
+	{ 0x13630, 0x0 },
+	{ 0x13730, 0x0 },
+	{ 0x13830, 0x0 },
+};  

The same as above. Please look into imx6q DDR3 training code.

Quoted 886 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +10 -0
+
+/* P0 message block paremeter for training firmware */
+struct dram_cfg_param lpddr4_fsp0_cfg[] = {
+	{ 0xd0000, 0x0 },
+	{ 0x54000, 0x0 },
+	{ 0x54001, 0x0 },
+	{ 0x54002, 0x0 },
+	{ 0x54003, 0xbb8 },
+	{ 0x54004, 0x2 },
+	{ 0x54005, ((LPDDR4_PHY_RON << 8) |

LPDDR4_PHY_RTT) },//PHY Ron/Rtt

board/freescale/imx8mm_evk/lpddr4_timing.c new file +75 -0
+	{ 0x54006, LPDDR4_PHY_VREF_VALUE },
+	{ 0x54007, 0x0 },
+	{ 0x54008, 0x131f },
+	{ 0x54009, 0xc8 },
+	{ 0x5400a, 0x0 },
+	{ 0x5400b, 0x2 },
+	{ 0x5400c, 0x0 },
+	{ 0x5400d, 0x0 },
+	{ 0x5400e, 0x0 },
+	{ 0x5400f, 0x0 },
+	{ 0x54010, 0x0 },
+	{ 0x54011, 0x0 },
+	{ 0x54012, (LPDDR4_CS << 8) | (0x110 & 0xff) },
+	{ 0x54013, 0x0 },
+	{ 0x54014, 0x0 },
+	{ 0x54015, 0x0 },
+	{ 0x54016, 0x0 },
+	{ 0x54017, 0x0 },
+	{ 0x54018, 0x0 },
+	{ 0x54019, 0x2dd4 },
+	{ 0x5401a, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x5401b, 0x4d66 },
+	{ 0x5401c, 0x4d08 },
+	{ 0x5401d, 0x0 },
+	{ 0x5401e, LPDDR4_MR22_RANK0/*0x16*/ },
+	{ 0x5401f, 0x2dd4 },
+	{ 0x54020, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x54021, 0x4d66 },
+	{ 0x54022, 0x4d08 },
+	{ 0x54023, 0x0 },
+	{ 0x54024, LPDDR4_MR22_RANK1/*0x16*/ },
+	{ 0x54025, 0x0 },
+	{ 0x54026, 0x0 },
+	{ 0x54027, 0x0 },
+	{ 0x54028, 0x0 },
+	{ 0x54029, 0x0 },
+	{ 0x5402a, 0x0 },
+	{ 0x5402b, 0x1000 },
+	{ 0x5402c, LPDDR4_CS },
+	{ 0x5402d, 0x0 },
+	{ 0x5402e, 0x0 },
+	{ 0x5402f, 0x0 },
+	{ 0x54030, 0x0 },
+	{ 0x54031, 0x0 },
+	{ 0x54032, 0xd400 },
+	{ 0x54033, (LPDDR4_MR3 << 8) | (0x312d & 0xff) },
+	{ 0x54034, 0x6600 },
+	{ 0x54035, 0x84d },
+	{ 0x54036, 0x4d },
+	{ 0x54037, (LPDDR4_MR22_RANK0 << 8)/*0x1600*/ },
+	{ 0x54038, 0xd400 },
+	{ 0x54039, (LPDDR4_MR3 << 8) | (0x312d & 0xff) },
+	{ 0x5403a, 0x6600 },
+	{ 0x5403b, 0x84d },
+	{ 0x5403c, 0x4d },
+	{ 0x5403d, (LPDDR4_MR22_RANK1 << 8)/*0x1600*/ },
+	{ 0x5403e, 0x0 },
+	{ 0x5403f, 0x0 },
+	{ 0x54040, 0x0 },
+	{ 0x54041, 0x0 },
+	{ 0x54042, 0x0 },
+	{ 0x54043, 0x0 },
+	{ 0x54044, 0x0 },
+	{ 0xd0000, 0x1 },
+};
+
+/* P1 message block paremeter for training firmware */
+struct dram_cfg_param lpddr4_fsp1_cfg[] = {
+	{ 0xd0000, 0x0 },
+	{ 0x54000, 0x0 },
+	{ 0x54001, 0x0 },
+	{ 0x54002, 0x101 },
+	{ 0x54003, 0x190 },
+	{ 0x54004, 0x2 },
+	{ 0x54005, ((LPDDR4_PHY_RON << 8) |

LPDDR4_PHY_RTT) },//PHY Ron/Rtt

board/freescale/imx8mm_evk/lpddr4_timing.c new file +75 -0
+	{ 0x54006, LPDDR4_PHY_VREF_VALUE },
+	{ 0x54007, 0x0 },
+	{ 0x54008, 0x121f },
+	{ 0x54009, 0xc8 },
+	{ 0x5400a, 0x0 },
+	{ 0x5400b, 0x2 },
+	{ 0x5400c, 0x0 },
+	{ 0x5400d, 0x0 },
+	{ 0x5400e, 0x0 },
+	{ 0x5400f, 0x0 },
+	{ 0x54010, 0x0 },
+	{ 0x54011, 0x0 },
+	{ 0x54012, (LPDDR4_CS << 8) | (0x110 & 0xff) },
+	{ 0x54013, 0x0 },
+	{ 0x54014, 0x0 },
+	{ 0x54015, 0x0 },
+	{ 0x54016, 0x0 },
+	{ 0x54017, 0x0 },
+	{ 0x54018, 0x0 },
+	{ 0x54019, 0x84 },
+	{ 0x5401a, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x5401b, 0x4d66 },
+	{ 0x5401c, 0x4d08 },
+	{ 0x5401d, 0x0 },
+	{ 0x5401e, LPDDR4_MR22_RANK0/*0x16*/ },
+	{ 0x5401f, 0x84 },
+	{ 0x54020, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x54021, 0x4d66 },
+	{ 0x54022, 0x4d08 },
+	{ 0x54023, 0x0 },
+	{ 0x54024, LPDDR4_MR22_RANK1/*0x16*/ },
+	{ 0x54025, 0x0 },
+	{ 0x54026, 0x0 },
+	{ 0x54027, 0x0 },
+	{ 0x54028, 0x0 },
+	{ 0x54029, 0x0 },
+	{ 0x5402a, 0x0 },
+	{ 0x5402b, 0x1000 },
+	{ 0x5402c, LPDDR4_CS },
+	{ 0x5402d, 0x0 },
+	{ 0x5402e, 0x0 },
+	{ 0x5402f, 0x0 },
+	{ 0x54030, 0x0 },
+	{ 0x54031, 0x0 },
+	{ 0x54032, 0x8400 },
+	{ 0x54033, (LPDDR4_MR3 << 8) | (0x3100 & 0xff) },
+	{ 0x54034, 0x6600 },
+	{ 0x54035, 0x84d },
+	{ 0x54036, 0x4d },
+	{ 0x54037, (LPDDR4_MR22_RANK0 << 8)/*0x1600*/ },
+	{ 0x54038, 0x8400 },
+	{ 0x54039, (LPDDR4_MR3 << 8) | (0x3100 & 0xff) },
+	{ 0x5403a, 0x6600 },
+	{ 0x5403b, 0x84d },
+	{ 0x5403c, 0x4d },
+	{ 0x5403d, (LPDDR4_MR22_RANK1 << 8)/*0x1600*/ },
+	{ 0x5403e, 0x0 },
+	{ 0x5403f, 0x0 },
+	{ 0x54040, 0x0 },
+	{ 0x54041, 0x0 },
+	{ 0x54042, 0x0 },
+	{ 0x54043, 0x0 },
+	{ 0x54044, 0x0 },
+	{ 0xd0000, 0x1 },
+};
+
+/* P1 message block paremeter for training firmware */
+struct dram_cfg_param lpddr4_fsp2_cfg[] = {
+	{ 0xd0000, 0x0 },
+	{ 0x54000, 0x0 },
+	{ 0x54001, 0x0 },
+	{ 0x54002, 0x102 },
+	{ 0x54003, 0x64 },
+	{ 0x54004, 0x2 },
+	{ 0x54005, ((LPDDR4_PHY_RON << 8) |

LPDDR4_PHY_RTT) },//PHY Ron/Rtt

board/freescale/imx8mm_evk/lpddr4_timing.c new file +75 -0
+	{ 0x54006, LPDDR4_PHY_VREF_VALUE },
+	{ 0x54007, 0x0 },
+	{ 0x54008, 0x121f },
+	{ 0x54009, 0xc8 },
+	{ 0x5400a, 0x0 },
+	{ 0x5400b, 0x2 },
+	{ 0x5400c, 0x0 },
+	{ 0x5400d, 0x0 },
+	{ 0x5400e, 0x0 },
+	{ 0x5400f, 0x0 },
+	{ 0x54010, 0x0 },
+	{ 0x54011, 0x0 },
+	{ 0x54012, (LPDDR4_CS << 8) | (0x110 & 0xff) },
+	{ 0x54013, 0x0 },
+	{ 0x54014, 0x0 },
+	{ 0x54015, 0x0 },
+	{ 0x54016, 0x0 },
+	{ 0x54017, 0x0 },
+	{ 0x54018, 0x0 },
+	{ 0x54019, 0x84 },
+	{ 0x5401a, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x5401b, 0x4d66 },
+	{ 0x5401c, 0x4d08 },
+	{ 0x5401d, 0x0 },
+	{ 0x5401e, LPDDR4_MR22_RANK0/*0x16*/ },
+	{ 0x5401f, 0x84 },
+	{ 0x54020, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x54021, 0x4d66 },
+	{ 0x54022, 0x4d08 },
+	{ 0x54023, 0x0 },
+	{ 0x54024, LPDDR4_MR22_RANK1/*0x16*/ },
+	{ 0x54025, 0x0 },
+	{ 0x54026, 0x0 },
+	{ 0x54027, 0x0 },
+	{ 0x54028, 0x0 },
+	{ 0x54029, 0x0 },
+	{ 0x5402a, 0x0 },
+	{ 0x5402b, 0x1000 },
+	{ 0x5402c, LPDDR4_CS },
+	{ 0x5402d, 0x0 },
+	{ 0x5402e, 0x0 },
+	{ 0x5402f, 0x0 },
+	{ 0x54030, 0x0 },
+	{ 0x54031, 0x0 },
+	{ 0x54032, 0x8400 },
+	{ 0x54033, (LPDDR4_MR3 << 8) | (0x3100 & 0xff) },
+	{ 0x54034, 0x6600 },
+	{ 0x54035, 0x84d },
+	{ 0x54036, 0x4d },
+	{ 0x54037, (LPDDR4_MR22_RANK0 << 8)/*0x1600*/ },
+	{ 0x54038, 0x8400 },
+	{ 0x54039, (LPDDR4_MR3 << 8) | (0x3100 & 0xff) },
+	{ 0x5403a, 0x6600 },
+	{ 0x5403b, 0x84d },
+	{ 0x5403c, 0x4d },
+	{ 0x5403d, (LPDDR4_MR22_RANK1 << 8)/*0x1600*/ },
+	{ 0x5403e, 0x0 },
+	{ 0x5403f, 0x0 },
+	{ 0x54040, 0x0 },
+	{ 0x54041, 0x0 },
+	{ 0x54042, 0x0 },
+	{ 0x54043, 0x0 },
+	{ 0x54044, 0x0 },
+	{ 0xd0000, 0x1 },
+};
+
+/* P0 2D message block paremeter for training firmware */
+struct dram_cfg_param lpddr4_fsp0_2d_cfg[] = {
+	{ 0xd0000, 0x0 },
+	{ 0x54000, 0x0 },
+	{ 0x54001, 0x0 },
+	{ 0x54002, 0x0 },
+	{ 0x54003, 0xbb8 },
+	{ 0x54004, 0x2 },
+	{ 0x54005, ((LPDDR4_PHY_RON << 8) |

LPDDR4_PHY_RTT) },//PHY Ron/Rtt

board/freescale/imx8mm_evk/lpddr4_timing.c new file +647 -0
+	{ 0x54006, LPDDR4_PHY_VREF_VALUE },
+	{ 0x54007, 0x0 },
+	{ 0x54008, 0x61 },
+	{ 0x54009, 0xc8 },
+	{ 0x5400a, 0x0 },
+	{ 0x5400b, 0x2 },
+	{ 0x5400c, 0x0 },
+	{ 0x5400d, 0x0 },
+	{ 0x5400e, 0x0 },
+	{ 0x5400f, 0x100 },
+	{ 0x54010, 0x1f7f },
+	{ 0x54011, 0x0 },
+	{ 0x54012, (LPDDR4_CS << 8) | (0x110 & 0xff) },
+	{ 0x54013, 0x0 },
+	{ 0x54014, 0x0 },
+	{ 0x54015, 0x0 },
+	{ 0x54016, 0x0 },
+	{ 0x54017, 0x0 },
+	{ 0x54018, 0x0 },
+	{ 0x54019, 0x2dd4 },
+	{ 0x5401a, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x5401b, 0x4d66 },
+	{ 0x5401c, 0x4d08 },
+	{ 0x5401d, 0x0 },
+	{ 0x5401e, LPDDR4_MR22_RANK0/*0x16*/ },
+	{ 0x5401f, 0x2dd4 },
+	{ 0x54020, (0x31 & 0xff00) | LPDDR4_MR3 },
+	{ 0x54021, 0x4d66 },
+	{ 0x54022, 0x4d08 },
+	{ 0x54023, 0x0 },
+	{ 0x54024, LPDDR4_MR22_RANK1/*0x16*/ },
+	{ 0x54025, 0x0 },
+	{ 0x54026, 0x0 },
+	{ 0x54027, 0x0 },
+	{ 0x54028, 0x0 },
+	{ 0x54029, 0x0 },
+	{ 0x5402a, 0x0 },
+	{ 0x5402b, 0x1000 },
+	{ 0x5402c, LPDDR4_CS },
+	{ 0x5402d, 0x0 },
+	{ 0x5402e, 0x0 },
+	{ 0x5402f, 0x0 },
+	{ 0x54030, 0x0 },
+	{ 0x54031, 0x0 },
+	{ 0x54032, 0xd400 },
+	{ 0x54033, (LPDDR4_MR3 << 8) | (0x312d & 0xff) },
+	{ 0x54034, 0x6600 },
+	{ 0x54035, 0x84d },
+	{ 0x54036, 0x4d },
+	{ 0x54037, (LPDDR4_MR22_RANK0 << 8)/*0x1600*/ },
+	{ 0x54038, 0xd400 },
+	{ 0x54039, (LPDDR4_MR3 << 8) | (0x312d & 0xff) },
+	{ 0x5403a, 0x6600 },
+	{ 0x5403b, 0x84d },
+	{ 0x5403c, 0x4d },
+	{ 0x5403d, (LPDDR4_MR22_RANK1 << 8)/*0x1600*/ },
+	{ 0x5403e, 0x0 },
+	{ 0x5403f, 0x0 },
+	{ 0x54040, 0x0 },
+	{ 0x54041, 0x0 },
+	{ 0x54042, 0x0 },
+	{ 0x54043, 0x0 },
+	{ 0x54044, 0x0 },
+	{ 0xd0000, 0x1 },
+};
+
+/* DRAM PHY init engine image */
+struct dram_cfg_param lpddr4_phy_pie[] = {
+	{ 0xd0000, 0x0 },
+	{ 0x90000, 0x10 },
+	{ 0x90001, 0x400 },
+	{ 0x90002, 0x10e },
+	{ 0x90003, 0x0 },
+	{ 0x90004, 0x0 },
+	{ 0x90005, 0x8 },
+	{ 0x90029, 0xb },
+	{ 0x9002a, 0x480 },
+	{ 0x9002b, 0x109 },
+	{ 0x9002c, 0x8 },
+	{ 0x9002d, 0x448 },
+	{ 0x9002e, 0x139 },
+	{ 0x9002f, 0x8 },
+	{ 0x90030, 0x478 },
+	{ 0x90031, 0x109 },
+	{ 0x90032, 0x0 },
+	{ 0x90033, 0xe8 },
+	{ 0x90034, 0x109 },
+	{ 0x90035, 0x2 },
+	{ 0x90036, 0x10 },
+	{ 0x90037, 0x139 },
+	{ 0x90038, 0xf },
+	{ 0x90039, 0x7c0 },
+	{ 0x9003a, 0x139 },
+	{ 0x9003b, 0x44 },
+	{ 0x9003c, 0x630 },
+	{ 0x9003d, 0x159 },
+	{ 0x9003e, 0x14f },
+	{ 0x9003f, 0x630 },
+	{ 0x90040, 0x159 },
+	{ 0x90041, 0x47 },
+	{ 0x90042, 0x630 },
+	{ 0x90043, 0x149 },
+	{ 0x90044, 0x4f },
+	{ 0x90045, 0x630 },
+	{ 0x90046, 0x179 },
+	{ 0x90047, 0x8 },
+	{ 0x90048, 0xe0 },
+	{ 0x90049, 0x109 },
+	{ 0x9004a, 0x0 },
+	{ 0x9004b, 0x7c8 },
+	{ 0x9004c, 0x109 },
+	{ 0x9004d, 0x0 },
+	{ 0x9004e, 0x1 },
+	{ 0x9004f, 0x8 },
+	{ 0x90050, 0x0 },
+	{ 0x90051, 0x45a },
+	{ 0x90052, 0x9 },
+	{ 0x90053, 0x0 },
+	{ 0x90054, 0x448 },
+	{ 0x90055, 0x109 },
+	{ 0x90056, 0x40 },
+	{ 0x90057, 0x630 },
+	{ 0x90058, 0x179 },
+	{ 0x90059, 0x1 },
+	{ 0x9005a, 0x618 },
+	{ 0x9005b, 0x109 },
+	{ 0x9005c, 0x40c0 },
+	{ 0x9005d, 0x630 },
+	{ 0x9005e, 0x149 },
+	{ 0x9005f, 0x8 },
+	{ 0x90060, 0x4 },
+	{ 0x90061, 0x48 },
+	{ 0x90062, 0x4040 },
+	{ 0x90063, 0x630 },
+	{ 0x90064, 0x149 },
+	{ 0x90065, 0x0 },
+	{ 0x90066, 0x4 },
+	{ 0x90067, 0x48 },
+	{ 0x90068, 0x40 },
+	{ 0x90069, 0x630 },
+	{ 0x9006a, 0x149 },
+	{ 0x9006b, 0x10 },
+	{ 0x9006c, 0x4 },
+	{ 0x9006d, 0x18 },
+	{ 0x9006e, 0x0 },
+	{ 0x9006f, 0x4 },
+	{ 0x90070, 0x78 },
+	{ 0x90071, 0x549 },
+	{ 0x90072, 0x630 },
+	{ 0x90073, 0x159 },
+	{ 0x90074, 0xd49 },
+	{ 0x90075, 0x630 },
+	{ 0x90076, 0x159 },
+	{ 0x90077, 0x94a },
+	{ 0x90078, 0x630 },
+	{ 0x90079, 0x159 },
+	{ 0x9007a, 0x441 },
+	{ 0x9007b, 0x630 },
+	{ 0x9007c, 0x149 },
+	{ 0x9007d, 0x42 },
+	{ 0x9007e, 0x630 },
+	{ 0x9007f, 0x149 },
+	{ 0x90080, 0x1 },
+	{ 0x90081, 0x630 },
+	{ 0x90082, 0x149 },
+	{ 0x90083, 0x0 },
+	{ 0x90084, 0xe0 },
+	{ 0x90085, 0x109 },
+	{ 0x90086, 0xa },
+	{ 0x90087, 0x10 },
+	{ 0x90088, 0x109 },
+	{ 0x90089, 0x9 },
+	{ 0x9008a, 0x3c0 },
+	{ 0x9008b, 0x149 },
+	{ 0x9008c, 0x9 },
+	{ 0x9008d, 0x3c0 },
+	{ 0x9008e, 0x159 },
+	{ 0x9008f, 0x18 },
+	{ 0x90090, 0x10 },
+	{ 0x90091, 0x109 },
+	{ 0x90092, 0x0 },
+	{ 0x90093, 0x3c0 },
+	{ 0x90094, 0x109 },
+	{ 0x90095, 0x18 },
+	{ 0x90096, 0x4 },
+	{ 0x90097, 0x48 },
+	{ 0x90098, 0x18 },
+	{ 0x90099, 0x4 },
+	{ 0x9009a, 0x58 },
+	{ 0x9009b, 0xa },
+	{ 0x9009c, 0x10 },
+	{ 0x9009d, 0x109 },
+	{ 0x9009e, 0x2 },
+	{ 0x9009f, 0x10 },
+	{ 0x900a0, 0x109 },
+	{ 0x900a1, 0x5 },
+	{ 0x900a2, 0x7c0 },
+	{ 0x900a3, 0x109 },
+	{ 0x900a4, 0x10 },
+	{ 0x900a5, 0x10 },
+	{ 0x900a6, 0x109 },
+	{ 0x40000, 0x811 },
+	{ 0x40020, 0x880 },
+	{ 0x40040, 0x0 },
+	{ 0x40060, 0x0 },
+	{ 0x40001, 0x4008 },
+	{ 0x40021, 0x83 },
+	{ 0x40041, 0x4f },
+	{ 0x40061, 0x0 },
+	{ 0x40002, 0x4040 },
+	{ 0x40022, 0x83 },
+	{ 0x40042, 0x51 },
+	{ 0x40062, 0x0 },
+	{ 0x40003, 0x811 },
+	{ 0x40023, 0x880 },
+	{ 0x40043, 0x0 },
+	{ 0x40063, 0x0 },
+	{ 0x40004, 0x720 },
+	{ 0x40024, 0xf },
+	{ 0x40044, 0x1740 },
+	{ 0x40064, 0x0 },
+	{ 0x40005, 0x16 },
+	{ 0x40025, 0x83 },
+	{ 0x40045, 0x4b },
+	{ 0x40065, 0x0 },
+	{ 0x40006, 0x716 },
+	{ 0x40026, 0xf },
+	{ 0x40046, 0x2001 },
+	{ 0x40066, 0x0 },
+	{ 0x40007, 0x716 },
+	{ 0x40027, 0xf },
+	{ 0x40047, 0x2800 },
+	{ 0x40067, 0x0 },
+	{ 0x40008, 0x716 },
+	{ 0x40028, 0xf },
+	{ 0x40048, 0xf00 },
+	{ 0x40068, 0x0 },
+	{ 0x40009, 0x720 },
+	{ 0x40029, 0xf },
+	{ 0x40049, 0x1400 },
+	{ 0x40069, 0x0 },
+	{ 0x4000a, 0xe08 },
+	{ 0x4002a, 0xc15 },
+	{ 0x4004a, 0x0 },
+	{ 0x4006a, 0x0 },
+	{ 0x4000b, 0x623 },
+	{ 0x4002b, 0x15 },
+	{ 0x4004b, 0x0 },
+	{ 0x4006b, 0x0 },
+	{ 0x4000c, 0x4028 },
+	{ 0x4002c, 0x80 },
+	{ 0x4004c, 0x0 },
+	{ 0x4006c, 0x0 },
+	{ 0x4000d, 0xe08 },
+	{ 0x4002d, 0xc1a },
+	{ 0x4004d, 0x0 },
+	{ 0x4006d, 0x0 },
+	{ 0x4000e, 0x623 },
+	{ 0x4002e, 0x1a },
+	{ 0x4004e, 0x0 },
+	{ 0x4006e, 0x0 },
+	{ 0x4000f, 0x4040 },
+	{ 0x4002f, 0x80 },
+	{ 0x4004f, 0x0 },
+	{ 0x4006f, 0x0 },
+	{ 0x40010, 0x2604 },
+	{ 0x40030, 0x15 },
+	{ 0x40050, 0x0 },
+	{ 0x40070, 0x0 },
+	{ 0x40011, 0x708 },
+	{ 0x40031, 0x5 },
+	{ 0x40051, 0x0 },
+	{ 0x40071, 0x2002 },
+	{ 0x40012, 0x8 },
+	{ 0x40032, 0x80 },
+	{ 0x40052, 0x0 },
+	{ 0x40072, 0x0 },
+	{ 0x40013, 0x2604 },
+	{ 0x40033, 0x1a },
+	{ 0x40053, 0x0 },
+	{ 0x40073, 0x0 },
+	{ 0x40014, 0x708 },
+	{ 0x40034, 0xa },
+	{ 0x40054, 0x0 },
+	{ 0x40074, 0x2002 },
+	{ 0x40015, 0x4040 },
+	{ 0x40035, 0x80 },
+	{ 0x40055, 0x0 },
+	{ 0x40075, 0x0 },
+	{ 0x40016, 0x60a },
+	{ 0x40036, 0x15 },
+	{ 0x40056, 0x1200 },
+	{ 0x40076, 0x0 },
+	{ 0x40017, 0x61a },
+	{ 0x40037, 0x15 },
+	{ 0x40057, 0x1300 },
+	{ 0x40077, 0x0 },
+	{ 0x40018, 0x60a },
+	{ 0x40038, 0x1a },
+	{ 0x40058, 0x1200 },
+	{ 0x40078, 0x0 },
+	{ 0x40019, 0x642 },
+	{ 0x40039, 0x1a },
+	{ 0x40059, 0x1300 },
+	{ 0x40079, 0x0 },
+	{ 0x4001a, 0x4808 },
+	{ 0x4003a, 0x880 },
+	{ 0x4005a, 0x0 },
+	{ 0x4007a, 0x0 },
+	{ 0x900a7, 0x0 },
+	{ 0x900a8, 0x790 },
+	{ 0x900a9, 0x11a },
+	{ 0x900aa, 0x8 },
+	{ 0x900ab, 0x7aa },
+	{ 0x900ac, 0x2a },
+	{ 0x900ad, 0x10 },
+	{ 0x900ae, 0x7b2 },
+	{ 0x900af, 0x2a },
+	{ 0x900b0, 0x0 },
+	{ 0x900b1, 0x7c8 },
+	{ 0x900b2, 0x109 },
+	{ 0x900b3, 0x10 },
+	{ 0x900b4, 0x2a8 },
+	{ 0x900b5, 0x129 },
+	{ 0x900b6, 0x8 },
+	{ 0x900b7, 0x370 },
+	{ 0x900b8, 0x129 },
+	{ 0x900b9, 0xa },
+	{ 0x900ba, 0x3c8 },
+	{ 0x900bb, 0x1a9 },
+	{ 0x900bc, 0xc },
+	{ 0x900bd, 0x408 },
+	{ 0x900be, 0x199 },
+	{ 0x900bf, 0x14 },
+	{ 0x900c0, 0x790 },
+	{ 0x900c1, 0x11a },
+	{ 0x900c2, 0x8 },
+	{ 0x900c3, 0x4 },
+	{ 0x900c4, 0x18 },
+	{ 0x900c5, 0xe },
+	{ 0x900c6, 0x408 },
+	{ 0x900c7, 0x199 },
+	{ 0x900c8, 0x8 },
+	{ 0x900c9, 0x8568 },
+	{ 0x900ca, 0x108 },
+	{ 0x900cb, 0x18 },
+	{ 0x900cc, 0x790 },
+	{ 0x900cd, 0x16a },
+	{ 0x900ce, 0x8 },
+	{ 0x900cf, 0x1d8 },
+	{ 0x900d0, 0x169 },
+	{ 0x900d1, 0x10 },
+	{ 0x900d2, 0x8558 },
+	{ 0x900d3, 0x168 },
+	{ 0x900d4, 0x70 },
+	{ 0x900d5, 0x788 },
+	{ 0x900d6, 0x16a },
+	{ 0x900d7, 0x1ff8 },
+	{ 0x900d8, 0x85a8 },
+	{ 0x900d9, 0x1e8 },
+	{ 0x900da, 0x50 },
+	{ 0x900db, 0x798 },
+	{ 0x900dc, 0x16a },
+	{ 0x900dd, 0x60 },
+	{ 0x900de, 0x7a0 },
+	{ 0x900df, 0x16a },
+	{ 0x900e0, 0x8 },
+	{ 0x900e1, 0x8310 },
+	{ 0x900e2, 0x168 },
+	{ 0x900e3, 0x8 },
+	{ 0x900e4, 0xa310 },
+	{ 0x900e5, 0x168 },
+	{ 0x900e6, 0xa },
+	{ 0x900e7, 0x408 },
+	{ 0x900e8, 0x169 },
+	{ 0x900e9, 0x6e },
+	{ 0x900ea, 0x0 },
+	{ 0x900eb, 0x68 },
+	{ 0x900ec, 0x0 },
+	{ 0x900ed, 0x408 },
+	{ 0x900ee, 0x169 },
+	{ 0x900ef, 0x0 },
+	{ 0x900f0, 0x8310 },
+	{ 0x900f1, 0x168 },
+	{ 0x900f2, 0x0 },
+	{ 0x900f3, 0xa310 },
+	{ 0x900f4, 0x168 },
+	{ 0x900f5, 0x1ff8 },
+	{ 0x900f6, 0x85a8 },
+	{ 0x900f7, 0x1e8 },
+	{ 0x900f8, 0x68 },
+	{ 0x900f9, 0x798 },
+	{ 0x900fa, 0x16a },
+	{ 0x900fb, 0x78 },
+	{ 0x900fc, 0x7a0 },
+	{ 0x900fd, 0x16a },
+	{ 0x900fe, 0x68 },
+	{ 0x900ff, 0x790 },
+	{ 0x90100, 0x16a },
+	{ 0x90101, 0x8 },
+	{ 0x90102, 0x8b10 },
+	{ 0x90103, 0x168 },
+	{ 0x90104, 0x8 },
+	{ 0x90105, 0xab10 },
+	{ 0x90106, 0x168 },
+	{ 0x90107, 0xa },
+	{ 0x90108, 0x408 },
+	{ 0x90109, 0x169 },
+	{ 0x9010a, 0x58 },
+	{ 0x9010b, 0x0 },
+	{ 0x9010c, 0x68 },
+	{ 0x9010d, 0x0 },
+	{ 0x9010e, 0x408 },
+	{ 0x9010f, 0x169 },
+	{ 0x90110, 0x0 },
+	{ 0x90111, 0x8b10 },
+	{ 0x90112, 0x168 },
+	{ 0x90113, 0x0 },
+	{ 0x90114, 0xab10 },
+	{ 0x90115, 0x168 },
+	{ 0x90116, 0x0 },
+	{ 0x90117, 0x1d8 },
+	{ 0x90118, 0x169 },
+	{ 0x90119, 0x80 },
+	{ 0x9011a, 0x790 },
+	{ 0x9011b, 0x16a },
+	{ 0x9011c, 0x18 },
+	{ 0x9011d, 0x7aa },
+	{ 0x9011e, 0x6a },
+	{ 0x9011f, 0xa },
+	{ 0x90120, 0x0 },
+	{ 0x90121, 0x1e9 },
+	{ 0x90122, 0x8 },
+	{ 0x90123, 0x8080 },
+	{ 0x90124, 0x108 },
+	{ 0x90125, 0xf },
+	{ 0x90126, 0x408 },
+	{ 0x90127, 0x169 },
+	{ 0x90128, 0xc },
+	{ 0x90129, 0x0 },
+	{ 0x9012a, 0x68 },
+	{ 0x9012b, 0x9 },
+	{ 0x9012c, 0x0 },
+	{ 0x9012d, 0x1a9 },
+	{ 0x9012e, 0x0 },
+	{ 0x9012f, 0x408 },
+	{ 0x90130, 0x169 },
+	{ 0x90131, 0x0 },
+	{ 0x90132, 0x8080 },
+	{ 0x90133, 0x108 },
+	{ 0x90134, 0x8 },
+	{ 0x90135, 0x7aa },
+	{ 0x90136, 0x6a },
+	{ 0x90137, 0x0 },
+	{ 0x90138, 0x8568 },
+	{ 0x90139, 0x108 },
+	{ 0x9013a, 0xb7 },
+	{ 0x9013b, 0x790 },
+	{ 0x9013c, 0x16a },
+	{ 0x9013d, 0x1f },
+	{ 0x9013e, 0x0 },
+	{ 0x9013f, 0x68 },
+	{ 0x90140, 0x8 },
+	{ 0x90141, 0x8558 },
+	{ 0x90142, 0x168 },
+	{ 0x90143, 0xf },
+	{ 0x90144, 0x408 },
+	{ 0x90145, 0x169 },
+	{ 0x90146, 0xc },
+	{ 0x90147, 0x0 },
+	{ 0x90148, 0x68 },
+	{ 0x90149, 0x0 },
+	{ 0x9014a, 0x408 },
+	{ 0x9014b, 0x169 },
+	{ 0x9014c, 0x0 },
+	{ 0x9014d, 0x8558 },
+	{ 0x9014e, 0x168 },
+	{ 0x9014f, 0x8 },
+	{ 0x90150, 0x3c8 },
+	{ 0x90151, 0x1a9 },
+	{ 0x90152, 0x3 },
+	{ 0x90153, 0x370 },
+	{ 0x90154, 0x129 },
+	{ 0x90155, 0x20 },
+	{ 0x90156, 0x2aa },
+	{ 0x90157, 0x9 },
+	{ 0x90158, 0x0 },
+	{ 0x90159, 0x400 },
+	{ 0x9015a, 0x10e },
+	{ 0x9015b, 0x8 },
+	{ 0x9015c, 0xe8 },
+	{ 0x9015d, 0x109 },
+	{ 0x9015e, 0x0 },
+	{ 0x9015f, 0x8140 },
+	{ 0x90160, 0x10c },
+	{ 0x90161, 0x10 },
+	{ 0x90162, 0x8138 },
+	{ 0x90163, 0x10c },
+	{ 0x90164, 0x8 },
+	{ 0x90165, 0x7c8 },
+	{ 0x90166, 0x101 },
+	{ 0x90167, 0x8 },
+	{ 0x90168, 0x0 },
+	{ 0x90169, 0x8 },
+	{ 0x9016a, 0x8 },
+	{ 0x9016b, 0x448 },
+	{ 0x9016c, 0x109 },
+	{ 0x9016d, 0xf },
+	{ 0x9016e, 0x7c0 },
+	{ 0x9016f, 0x109 },
+	{ 0x90170, 0x0 },
+	{ 0x90171, 0xe8 },
+	{ 0x90172, 0x109 },
+	{ 0x90173, 0x47 },
+	{ 0x90174, 0x630 },
+	{ 0x90175, 0x109 },
+	{ 0x90176, 0x8 },
+	{ 0x90177, 0x618 },
+	{ 0x90178, 0x109 },
+	{ 0x90179, 0x8 },
+	{ 0x9017a, 0xe0 },
+	{ 0x9017b, 0x109 },
+	{ 0x9017c, 0x0 },
+	{ 0x9017d, 0x7c8 },
+	{ 0x9017e, 0x109 },
+	{ 0x9017f, 0x8 },
+	{ 0x90180, 0x8140 },
+	{ 0x90181, 0x10c },
+	{ 0x90182, 0x0 },
+	{ 0x90183, 0x1 },
+	{ 0x90184, 0x8 },
+	{ 0x90185, 0x8 },
+	{ 0x90186, 0x4 },
+	{ 0x90187, 0x8 },
+	{ 0x90188, 0x8 },
+	{ 0x90189, 0x7c8 },
+	{ 0x9018a, 0x101 },
+	{ 0x90006, 0x0 },
+	{ 0x90007, 0x0 },
+	{ 0x90008, 0x8 },
+	{ 0x90009, 0x0 },
+	{ 0x9000a, 0x0 },
+	{ 0x9000b, 0x0 },
+	{ 0xd00e7, 0x400 },
+	{ 0x90017, 0x0 },
+	{ 0x9001f, 0x2a },
+	{ 0x90026, 0x6a },
+	{ 0x400d0, 0x0 },
+	{ 0x400d1, 0x101 },
+	{ 0x400d2, 0x105 },
+	{ 0x400d3, 0x107 },
+	{ 0x400d4, 0x10f },
+	{ 0x400d5, 0x202 },
+	{ 0x400d6, 0x20a },
+	{ 0x400d7, 0x20b },
+	{ 0x2003a, 0x2 },
+	{ 0x2000b, 0x5d },
+	{ 0x2000c, 0xbb },
+	{ 0x2000d, 0x753 },
+	{ 0x2000e, 0x2c },
+	{ 0x12000b, 0xc },
+	{ 0x12000c, 0x19 },
+	{ 0x12000d, 0xfa },
+	{ 0x12000e, 0x10 },
+	{ 0x22000b, 0x3 },
+	{ 0x22000c, 0x6 },
+	{ 0x22000d, 0x3e },
+	{ 0x22000e, 0x10 },
+	{ 0x9000c, 0x0 },
+	{ 0x9000d, 0x173 },
+	{ 0x9000e, 0x60 },
+	{ 0x9000f, 0x6110 },
+	{ 0x90010, 0x2152 },
+	{ 0x90011, 0xdfbd },
+	{ 0x90012, 0x60 },
+	{ 0x90013, 0x6152 },
+	{ 0x20010, 0x5a },
+	{ 0x20011, 0x3 },
+	{ 0x40080, 0xe0 },
+	{ 0x40081, 0x12 },
+	{ 0x40082, 0xe0 },
+	{ 0x40083, 0x12 },
+	{ 0x40084, 0xe0 },
+	{ 0x40085, 0x12 },
+	{ 0x140080, 0xe0 },
+	{ 0x140081, 0x12 },
+	{ 0x140082, 0xe0 },
+	{ 0x140083, 0x12 },
+	{ 0x140084, 0xe0 },
+	{ 0x140085, 0x12 },
+	{ 0x240080, 0xe0 },
+	{ 0x240081, 0x12 },
+	{ 0x240082, 0xe0 },
+	{ 0x240083, 0x12 },
+	{ 0x240084, 0xe0 },
+	{ 0x240085, 0x12 },
+	{ 0x400fd, 0xf },
+	{ 0x10011, 0x1 },
+	{ 0x10012, 0x1 },
+	{ 0x10013, 0x180 },
+	{ 0x10018, 0x1 },
+	{ 0x10002, 0x6209 },
+	{ 0x100b2, 0x1 },
+	{ 0x101b4, 0x1 },
+	{ 0x102b4, 0x1 },
+	{ 0x103b4, 0x1 },
+	{ 0x104b4, 0x1 },
+	{ 0x105b4, 0x1 },
+	{ 0x106b4, 0x1 },
+	{ 0x107b4, 0x1 },
+	{ 0x108b4, 0x1 },
+	{ 0x11011, 0x1 },
+	{ 0x11012, 0x1 },
+	{ 0x11013, 0x180 },
+	{ 0x11018, 0x1 },
+	{ 0x11002, 0x6209 },
+	{ 0x110b2, 0x1 },
+	{ 0x111b4, 0x1 },
+	{ 0x112b4, 0x1 },
+	{ 0x113b4, 0x1 },
+	{ 0x114b4, 0x1 },
+	{ 0x115b4, 0x1 },
+	{ 0x116b4, 0x1 },
+	{ 0x117b4, 0x1 },
+	{ 0x118b4, 0x1 },
+	{ 0x12011, 0x1 },
+	{ 0x12012, 0x1 },
+	{ 0x12013, 0x180 },
+	{ 0x12018, 0x1 },
+	{ 0x12002, 0x6209 },
+	{ 0x120b2, 0x1 },
+	{ 0x121b4, 0x1 },
+	{ 0x122b4, 0x1 },
+	{ 0x123b4, 0x1 },
+	{ 0x124b4, 0x1 },
+	{ 0x125b4, 0x1 },
+	{ 0x126b4, 0x1 },
+	{ 0x127b4, 0x1 },
+	{ 0x128b4, 0x1 },
+	{ 0x13011, 0x1 },
+	{ 0x13012, 0x1 },
+	{ 0x13013, 0x180 },
+	{ 0x13018, 0x1 },
+	{ 0x13002, 0x6209 },
+	{ 0x130b2, 0x1 },
+	{ 0x131b4, 0x1 },
+	{ 0x132b4, 0x1 },

board/freescale/imx8mm_evk/lpddr4_timing.c

Quoted 10 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +10 -0
+	{ 0x133b4, 0x1 },
+	{ 0x134b4, 0x1 },
+	{ 0x135b4, 0x1 },
+	{ 0x136b4, 0x1 },
+	{ 0x137b4, 0x1 },
+	{ 0x138b4, 0x1 },
+	{ 0x2003a, 0x2 },
+	{ 0xc0080, 0x2 },
+	{ 0xd0000, 0x1 },
+};  

The same as above.

Quoted 47 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +8 -0
+
+struct dram_fsp_msg lpddr4_dram_fsp_msg[] = {
+	{
+		/* P0 3000mts 1D */
+		.drate = 3000,
+		.fw_type = FW_1D_IMAGE,
+		.fsp_cfg = lpddr4_fsp0_cfg,
+		.fsp_cfg_num =

ARRAY_SIZE(lpddr4_fsp0_cfg),

board/freescale/imx8mm_evk/lpddr4_timing.c new file +7 -0
+	},
+	{
+		/* P0 3000mts 2D */
+		.drate = 3000,
+		.fw_type = FW_2D_IMAGE,
+		.fsp_cfg = lpddr4_fsp0_2d_cfg,
+		.fsp_cfg_num =

ARRAY_SIZE(lpddr4_fsp0_2d_cfg),

board/freescale/imx8mm_evk/lpddr4_timing.c new file +7 -0
+	},
+	{
+		/* P1 400mts 1D */
+		.drate = 400,
+		.fw_type = FW_1D_IMAGE,
+		.fsp_cfg = lpddr4_fsp1_cfg,
+		.fsp_cfg_num =

ARRAY_SIZE(lpddr4_fsp1_cfg),

board/freescale/imx8mm_evk/lpddr4_timing.c new file +7 -0
+	},
+	{
+		/* P1 100mts 1D */
+		.drate = 100,
+		.fw_type = FW_1D_IMAGE,
+		.fsp_cfg = lpddr4_fsp2_cfg,
+		.fsp_cfg_num =

ARRAY_SIZE(lpddr4_fsp2_cfg),

board/freescale/imx8mm_evk/lpddr4_timing.c new file +13 -0
+	},
+};
+
+/* lpddr4 timing config params on EVK board */
+struct dram_timing_info dram_timing = {
+	.ddrc_cfg = lpddr4_ddrc_cfg,
+	.ddrc_cfg_num = ARRAY_SIZE(lpddr4_ddrc_cfg),
+	.ddrphy_cfg = lpddr4_ddrphy_cfg,
+	.ddrphy_cfg_num = ARRAY_SIZE(lpddr4_ddrphy_cfg),
+	.fsp_msg = lpddr4_dram_fsp_msg,
+	.fsp_msg_num = ARRAY_SIZE(lpddr4_dram_fsp_msg),
+	.ddrphy_trained_csr = lpddr4_ddrphy_trained_csr,
+	.ddrphy_trained_csr_num =

ARRAY_SIZE(lpddr4_ddrphy_trained_csr),

board/freescale/imx8mm_evk/lpddr4_timing.c

Quoted 2 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +2 -0
+	.ddrphy_pie = lpddr4_phy_pie,
+	.ddrphy_pie_num = ARRAY_SIZE(lpddr4_phy_pie),  

It would be best to get the above values calculated dynamically for this SoC.

Quoted 29 lines
board/freescale/imx8mm_evk/lpddr4_timing.c new file +1 -0
+};
(quoted diff) +0 -0

b/board/freescale/imx8mm_evk/spl.c new file mode 100644 index 0000000000..cf1dfc2c2a

board/freescale/imx8mm_evk/spl.c new file +22 -0
@@ -0,0 +1,187 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/arch/imx8mm_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <power/pmic.h>
+#include <asm/arch/clock.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <asm/arch/ddr.h>
+
+DECLARE_GLOBAL_DATA_PTR;

board/freescale/imx8mm_evk/spl.c line 32

Quoted 10 lines
board/freescale/imx8mm_evk/spl.c new file +10 -0
+
+void spl_dram_init(void)
+{
+	ddr_init(&dram_timing);
+}
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(2, 18)
+#define USDHC2_PWR_GPIO IMX_GPIO_NR(2, 19)
+
+#define USDHC_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS |  

PAD_CTL_PUE | \

Quoted 24 lines
board/freescale/imx8mm_evk/spl.c new file +5 -0
+			PAD_CTL_PE | PAD_CTL_FSEL2)
+#define USDHC_GPIO_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE1)
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	IMX8MM_PAD_NAND_WE_B_USDHC3_CLK |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_WP_B_USDHC3_CMD |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_DATA04_USDHC3_DATA0 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_DATA05_USDHC3_DATA1 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_DATA06_USDHC3_DATA2 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_DATA07_USDHC3_DATA3 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_RE_B_USDHC3_DATA4 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_CE2_B_USDHC3_DATA5 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_CE3_B_USDHC3_DATA6 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_NAND_CLE_USDHC3_DATA7 |

MUX_PAD_CTRL(USDHC_PAD_CTRL), +};

board/freescale/imx8mm_evk/spl.c

Quoted 3 lines
board/freescale/imx8mm_evk/spl.c new file +3 -0
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	IMX8MM_PAD_SD2_CLK_USDHC2_CLK |  

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c

Quoted 1 line
board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_CMD_USDHC2_CMD |  

MUX_PAD_CTRL(USDHC_PAD_CTRL),

Quoted 60 lines
board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_DATA0_USDHC2_DATA0 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_DATA1_USDHC2_DATA1 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_DATA2_USDHC2_DATA2 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 |

MUX_PAD_CTRL(USDHC_PAD_CTRL),

board/freescale/imx8mm_evk/spl.c new file +1 -0
+	IMX8MM_PAD_SD2_RESET_B_GPIO2_IO19 |

MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL), +};

board/freescale/imx8mm_evk/spl.c new file +4 -0
+
+/*
+ * The evk board uses DAT3 to detect CD card plugin,
+ * in u-boot we mux the pin to GPIO when doing

board_mmc_getcd.
+ */

board/freescale/imx8mm_evk/spl.c new file +2 -0
+static iomux_v3_cfg_t const usdhc2_cd_pad =
+	IMX8MM_PAD_SD2_DATA3_GPIO2_IO18 |

MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL); +

board/freescale/imx8mm_evk/spl.c new file +14 -0
+static iomux_v3_cfg_t const usdhc2_dat3_pad =
+	IMX8MM_PAD_SD2_DATA3_USDHC2_DATA3 |
+	MUX_PAD_CTRL(USDHC_PAD_CTRL);
+
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+	{USDHC2_BASE_ADDR, 0, 1},
+	{USDHC3_BASE_ADDR, 0, 1},
+};
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+	/*
+	 * According to the board_mmc_init() the

following map is done:

board/freescale/imx8mm_evk/spl.c new file +8 -0
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0                    USDHC1
+	 * mmc1                    USDHC2
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			usdhc_cfg[0].sdhc_clk =

mxc_get_clock(MXC_ESDHC2_CLK);
+
imx_iomux_v3_setup_multiple_pads(usdhc2_pads, + ARRAY_SIZE(usdhc2_pads));

board/freescale/imx8mm_evk/spl.c new file +1 -0
+			gpio_request(USDHC2_PWR_GPIO,

"usdhc2_reset");
+
gpio_direction_output(USDHC2_PWR_GPIO, 0);

board/freescale/imx8mm_evk/spl.c new file +2 -0
+			udelay(500);
+

gpio_direction_output(USDHC2_PWR_GPIO, 1);

board/freescale/imx8mm_evk/spl.c new file +3 -0
+			break;
+		case 1:
+			usdhc_cfg[1].sdhc_clk =

mxc_get_clock(MXC_ESDHC3_CLK);
+
imx_iomux_v3_setup_multiple_pads(usdhc3_pads, + ARRAY_SIZE(usdhc3_pads));

board/freescale/imx8mm_evk/spl.c

Quoted 1 line
board/freescale/imx8mm_evk/spl.c new file +1 -0
+			break;  

It would be best if you could enable DM/DTS in SPL too from the outset (and share the SPL size).

Do you have any timeline for converting SPL to DM/DTS?

Quoted 106 lines
board/freescale/imx8mm_evk/spl.c new file +2 -0
+		default:
+			printf("USDHC controllers %d not

supported \n", i + 1);

board/freescale/imx8mm_evk/spl.c new file +4 -0
+			return -EINVAL;
+		}
+
+		ret = fsl_esdhc_initialize(bis,

&usdhc_cfg[i]);

board/freescale/imx8mm_evk/spl.c new file +10 -0
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg

*)mmc->priv;

board/freescale/imx8mm_evk/spl.c new file +9 -0
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC3_BASE_ADDR:
+		ret = 1;
+		break;
+	case USDHC2_BASE_ADDR:
+		imx_iomux_v3_setup_pad(usdhc2_cd_pad);
+		gpio_request(USDHC2_CD_GPIO, "usdhc2

cd");

board/freescale/imx8mm_evk/spl.c new file +4 -0
+		gpio_direction_input(USDHC2_CD_GPIO);
+
+		/*
+		 * Since it is the DAT3 pin, this pin is

pulled to

board/freescale/imx8mm_evk/spl.c new file +20 -0
+		 * low voltage if no card
[… more lines in the raw message]

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

choose */

board/freescale/imx8mm_evk/spl.c new file +39 -0

Lines of this file are not shown. View the raw message.

(quoted diff) +0 -0

The rest of this diff is not shown. View the raw message.

b/configs/imx8mm_evk_defconfig new file mode 100644 index 0000000000..6110f23e38

configs/imx8mm_evk_defconfig new file +6 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Quoted 8 lines
Quoted 8 lines
Quoted 7 lines
Quoted 7 lines

configs/imx8mm_evk_defconfig

Quoted 7 lines
configs/imx8mm_evk_defconfig new file +6 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

+CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"

Quoted 3 lines
Quoted 3 lines
Quoted 2 lines
Quoted 2 lines
Quoted 1 line

+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/imx8m

Quoted 50 lines
Quoted 50 lines
Quoted 50 lines
Quoted 50 lines

/imximage.cfg,SPL_TEXT_BASE=0x7E1000"

configs/imx8mm_evk_defconfig

Quoted 20 lines
configs/imx8mm_evk_defconfig new file +20 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Here you enable the DM_ETH, but the welcome u-boot info says:

"Net: No ethernet found."

Quoted 23 lines
configs/imx8mm_evk_defconfig new file +7 -0

Lines of this file are not shown. View the raw message.

(quoted diff) +0 -0

The rest of this diff is not shown. View the raw message.

b/include/configs/imx8mm_evk.h new file mode 100644 index 0000000000..f944308757

include/configs/imx8mm_evk.h new file +10 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

8K region */ +#endif

include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

1024) +#define

CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR

Quoted 162 lines
Quoted 162 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line

+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR

	0x300  
Quoted 15 lines
Quoted 15 lines

include/configs/imx8mm_evk.h

Quoted 3 lines
include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR *

Quoted 10 lines

512) +

include/configs/imx8mm_evk.h new file +6 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
+#define CONFIG_SPL_STACK 0x91fff0 +#define
CONFIG_SPL_LIBCOMMON_SUPPORT +#define

CONFIG_SPL_LIBGENERIC_SUPPORT

Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

8 KB */ +#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 /*
512 KB */ +#define CONFIG_SYS_ICACHE_OFF

include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

malloc f used before GD_FLG_FULL_MALLOC_INIT set */ + +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image

gives a

Quoted 134 lines
Quoted 134 lines

error

include/configs/imx8mm_evk.h

Quoted 4 lines

info not panic */ +

include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Why do you need to undef those config options?

include/configs/imx8mm_evk.h

Quoted 20 lines
include/configs/imx8mm_evk.h new file +20 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

There seems to be some issue with inheritance, as you need to undef those values manually.

Why is it needed?

Quoted 100 lines
include/configs/imx8mm_evk.h new file +27 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

earlycon=ec_imx6q,0x30890000,115200\0" \

include/configs/imx8mm_evk.h new file +7 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

\

include/configs/imx8mm_evk.h new file +1 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

__stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \

include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

console=${console} root=${mmcroot}\0 " \

include/configs/imx8mm_evk.h new file +1 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${loadaddr} ${script};\0" \

include/configs/imx8mm_evk.h new file +1 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

mmc ...; " \

include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${loadaddr} ${image}\0" \

include/configs/imx8mm_evk.h new file +1 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${fdt_addr} ${fdt_file}\0" \

include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${boot_fdt} = try; then " \

include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${fdt_addr}; " \

include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

the DT; " \

include/configs/imx8mm_evk.h new file +5 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

console=${console} " \

include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

nfsroot=${serverip}:${nfsroot},v3,tcp\0" \

include/configs/imx8mm_evk.h new file +9 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${boot_fdt} = try; then " \

include/configs/imx8mm_evk.h new file +1 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${fdt_file}; then " \

include/configs/imx8mm_evk.h new file +1 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

${fdt_addr}; " \

include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

the DT; " \

include/configs/imx8mm_evk.h new file +13 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

include/configs/imx8mm_evk.h

Quoted 8 lines
include/configs/imx8mm_evk.h new file +8 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

CONFIG_LOADADDR

Quoted 76 lines
Quoted 76 lines
Quoted 76 lines
Quoted 76 lines

include/configs/imx8mm_evk.h

Quoted 26 lines
include/configs/imx8mm_evk.h new file +5 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \

include/configs/imx8mm_evk.h new file +1 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

CONFIG_SYS_INIT_SP_OFFSET) +

include/configs/imx8mm_evk.h new file +6 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

USDHC2 */ +#define
CONFIG_MMCROOT "/dev/mmcblk1p2" /*
USDHC2 */ + +/* Size of malloc() pool */

include/configs/imx8mm_evk.h new file +5 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

0x80000000 /* 2GB DDR */ +

include/configs/imx8mm_evk.h new file +2 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

(CONFIG_SYS_MEMTEST_START +

Quoted 33 lines

(PHYS_SDRAM_SIZE >> 1)) +

include/configs/imx8mm_evk.h new file +3 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

UART2_BASE_ADDR +

include/configs/imx8mm_evk.h new file +8 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

(CONFIG_SYS_CBSIZE
+ \ +
sizeof(CONFIG_SYS_PROMPT) + 16) +

include/configs/imx8mm_evk.h new file +11 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

*/ +#define CONFIG_SYS_MMC_IMG_LOAD_PART 1

include/configs/imx8mm_evk.h new file +5 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Quoted 4 lines

I2C bus 1 */ +#define
CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus
2 */ +#define CONFIG_SYS_I2C_MXC_I2C3 /*
enable I2C bus 3 */ +#define CONFIG_SYS_I2C_SPEED 100000

Some of those values are (SYS_I2C_*, MXC_OCOTP, FSL_*) are already supported by Kconfig. Please use Kconfig instead.

include/configs/imx8mm_evk.h

Quoted 4 lines
include/configs/imx8mm_evk.h new file +4 -0

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Best regards,

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director:

Wolfgang

Quoted 9 lines
Quoted 9 lines
Quoted 3 lines
Quoted 3 lines

Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-59 Fax:
(+49)-8142-66989-80 Email: lukma at denx.de

Best regards,

Quoted 8 lines
Quoted 8 lines

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang
Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-59 Fax:
(+49)-8142-66989-80 Email: lukma at denx.de

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang
Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
lukma at denx.de

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190130/5f31757e/attachment.sig>

Part of the diff is not shown here. View the raw message.