spi: spi-mem: Add driver for NXP FlexSPI controller
Subsystems (5)
v8 cover spi: spi-mem: Add driver for NXP FlexSPI controller
- Add driver for NXP FlexSPI host controller
FlexSPI is a flexsible SPI host controller [1], Chapter 30 page 1475,
which supports two SPI channels and up to 4 external devices.
Each channel supports Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional data lines) i.e. FlexSPI acts as an interface to external devices, maximum 4, each with up to 8 bidirectional data lines.
- Tested this driver with mtd_debug(Erase/Write/Read) utility and JFFS2 filesystem mounting and booting on NXP LX2160ARDB[2] and LX2160AQDS targets. LX2160ARDB is having two NOR slave device connected on single bus A i.e. A0 and A1 (CS0 and CS1).
LX2160AQDS is having two NOR slave device connected on separate buses one flash on A0 and second on B1 i.e. (CS0 and CS3).
Verified this driver on following SPI NOR flashes:
Micron, mt35xu512aba, [Read - 1 bit mode]
Cypress, s25fl512s, [Read - 1/2/4 bit mode]
[1] https://www.nxp.com/docs/en/reference-manual/IMXRT1050RM.pdf
[2] https://patchwork.kernel.org/project/linux-arm-kernel/list/?submitter=182097
Yogesh Narayan Gaur (5):
spi: spi-mem: Add driver for NXP FlexSPI controller
dt-bindings: spi: add binding file for NXP FlexSPI controller
arm64: dts: lx2160a: add FlexSPI node property
arm64: defconfig: enable NXP FlexSPI driver
MAINTAINERS: add maintainers for the NXP FlexSPI driver
Changes for v8:
- Incorporated review comments for
patch 'spi: spi-mem: Add driver for NXP FlexSPI controller'
- Update MAINTAINERS file
Changes for v7:
- Rebase on top of SPI tree
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git/
branch: for-next
- Incorporated review comments for
patch 'spi: spi-mem: Add driver for NXP FlexSPI controller'.
Changes for v6:
- Rebase on top of v5.0-rc1.
- Incorporated review comments for
patch 'spi: spi-mem: Add driver for NXP FlexSPI controller'.
- Updated s-b tag in all patches.
Changes for v5:
- Rebase on top of v4.20-rc2
- Incorporated review comments for
patch 'spi: spi-mem: Add driver for NXP FlexSPI controller'.
Changes for v4:
- Incorporated review comments for
patch 'spi: spi-mem: Add driver for NXP FlexSPI controller'.
- Incorporated binding file review comments.
Changes for v3:
- Incorporated review comments for
patch 'spi: spi-mem: Add driver for NXP FlexSPI controller'.
Changes for v2:
- Incorporated Boris review comments and drop below patches as per the comments.
- Patch 'spi: add slave device size in spi_device struct'
- Patch 'spi: add flags for octal I/O data transfer'
- Incorporated DTS and Binding file review comments of Shawn Guo and Rob Herring.
.../devicetree/bindings/spi/spi-nxp-fspi.txt | 39 + MAINTAINERS | 8 + .../boot/dts/freescale/fsl-lx2160a-rdb.dts | 22 + .../arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 13 + arch/arm64/configs/defconfig | 1 + drivers/spi/Kconfig | 10 + drivers/spi/Makefile | 1 + drivers/spi/spi-nxp-fspi.c | 1105 +++++++++++++++++ 8 files changed, 1199 insertions(+) create mode 100644 Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt create mode 100644 drivers/spi/spi-nxp-fspi.c
Signature · 6 lines
2.17.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH v8 1/5 spi: spi-mem: Add driver for NXP FlexSPI controller
- Add driver for NXP FlexSPI host controller
(0) What is the FlexSPI controller?
FlexSPI is a flexsible SPI host controller which supports two SPI channels and up to 4 external devices. Each channel supports Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional data lines) i.e. FlexSPI acts as an interface to external devices, maximum 4, each with up to 8 bidirectional data lines.
It uses new SPI memory interface of the SPI framework to issue flash memory operations to up to four connected flash devices (2 buses with 2 CS each).
(1) Tested this driver with the mtd_debug and JFFS2 filesystem utility on NXP LX2160ARDB and LX2160AQDS targets.
LX2160ARDB is having two NOR slave device connected on single bus A i.e. A0 and A1 (CS0 and CS1).
LX2160AQDS is having two NOR slave device connected on separate buses one flash on A0 and second on B1 i.e. (CS0 and CS3). Verified this driver on following SPI NOR flashes:
Micron, mt35xu512ab, [Read - 1 bit mode]
Cypress, s25fl512s, [Read - 1/2/4 bit mode]---
Changes for v8:
- Typo review comments changes
- Fix logic of read data for case when read size is less than 8 bytes.
- Add correct email address of Boris
- Add r-o-b tag of Frieder and Boris
Changes for v7:
- Add func pointer for '.get_name' for struct spi_controller_mem_ops
- Add input address range check as per controller memory mapped space
- Update _fill_txfifo/_read_rxfifo funcs as per Frieder review comments Changes for v6:
- Rebase on top of v5.0-rc1
- Updated as per Frieder review comments and perform code cleanup
- Updated _fill_txfifo/_read_rxfifo func write/read logic Changes for v5:
- Rebase on top of v4.20-rc2
- Modified fspi_readl_poll_tout() as per review comments
- Arrange header file in alphabetical order
- Removed usage of read()/write() function callback pointer
- Add support for 1 and 2 byte address length
- Change Frieder e-mail to new e-mail address
Changes for v4:
- Incorporate Boris review comments
* Use readl_poll_timeout() instead of busy looping.
* Re-define register masking as per comment.
* Drop fspi_devtype enum.
Changes for v3:
- Added endianness flag in platform specific structure instead of DTS.
- Modified nxp_fspi_read_ahb(), removed remapping code.
- Added Boris and Frieder as Author and provided reference of spi-fsl-qspi.c Changes for v2:
- Incorporated Boris review comments.
- Remove dependency of driver over connected flash device size.
- Modified the logic to select requested CS.
- Remove SPI-Octal Macros.
drivers/spi/Kconfig | 10 + drivers/spi/Makefile | 1 + drivers/spi/spi-nxp-fspi.c | 1105 ++++++++++++++++++++++++++++++++++++ 3 files changed, 1116 insertions(+) create mode 100644 drivers/spi/spi-nxp-fspi.c
drivers/spi/Kconfig +10 -0
@@ -279,6 +279,16 @@ config SPI_FSL_QUADSPI This controller does not support generic SPI messages. It only supports the high-level SPI memory interface. +config SPI_NXP_FLEXSPI + tristate "NXP Flex SPI controller" + depends on ARCH_LAYERSCAPE || HAS_IOMEM + help + This enables support for the Flex SPI controller in master mode. + Up to four slave devices can be connected on two buses with two + chipselects each. + This controller does not support generic SPI messages and only + supports the high-level SPI memory interface. + config SPI_GPIO tristate "GPIO-based bitbanging SPI Master" depends on GPIOLIB || COMPILE_TEST
drivers/spi/Makefile +1 -0
@@ -64,6 +64,7 @@ obj-$(CONFIG_SPI_MXIC) += spi-mxic.o obj-$(CONFIG_SPI_MXS) += spi-mxs.o obj-$(CONFIG_SPI_NPCM_PSPI) += spi-npcm-pspi.o obj-$(CONFIG_SPI_NUC900) += spi-nuc900.o +obj-$(CONFIG_SPI_NXP_FLEXSPI) += spi-nxp-fspi.o obj-$(CONFIG_SPI_OC_TINY) += spi-oc-tiny.o spi-octeon-objs := spi-cavium.o spi-cavium-octeon.o obj-$(CONFIG_SPI_OCTEON) += spi-octeon.o
drivers/spi/spi-nxp-fspi.c new file +1105 -0
1,105 lines not on this page · raw message
+MODULE_LICENSE("GPL v2");
Signature · 1 line
2.17.1
Hello Mark,
Can you please apply below patch in SPI tree?
Patch has been reviewed by Boris and Frieder.
--
Regards
Yogesh Gaur
Quoted 1,220 lines
-----Original Message-----
From: Yogesh Narayan Gaur
Sent: Tuesday, January 15, 2019 5:30 PM
To: [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]
Cc: [email protected]; [email protected]; [email protected]; linux- [email protected]; [email protected]; [email protected]; [email protected]; Yogesh Narayan Gaur <[email protected]>
Subject: [PATCH v8 1/5] spi: spi-mem: Add driver for NXP FlexSPI controller- Add driver for NXP FlexSPI host controller
(0) What is the FlexSPI controller?
FlexSPI is a flexsible SPI host controller which supports two SPI channels and up
to 4 external devices. Each channel supports Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional data lines) i.e. FlexSPI acts as an interface to external devices, maximum 4, each with up to 8 bidirectional data lines.It uses new SPI memory interface of the SPI framework to issue flash memory
operations to up to four connected flash devices (2 buses with 2 CS each).(1) Tested this driver with the
mtd_debugand JFFS2 filesystem utility on NXP LX2160ARDB and LX2160AQDS targets.
LX2160ARDB is having two NOR slave device connected on single bus A i.e. A0
and A1 (CS0 and CS1).
LX2160AQDS is having two NOR slave device connected on separate buses one
flash on A0 and second on B1 i.e. (CS0 and CS3).
Verified this driver on following SPI NOR flashes:Micron, mt35xu512ab, [Read - 1 bit mode] Cypress, s25fl512s, [Read - 1/2/4 bit mode]Signed-off-by Yogesh Narayan Gaur <[email protected]>Reviewed-by Frieder Schrempf <[email protected]>Reviewed-by Boris Brezillon <[email protected]>---
Changes for v8:
- Typo review comments changes
- Fix logic of read data for case when read size is less than 8 bytes.
- Add correct email address of Boris
- Add r-o-b tag of Frieder and Boris
Changes for v7:
- Add func pointer for '.get_name' for structspi_controller_mem_ops
- Add input address range check as per controller memory mapped space
- Update _fill_txfifo/_read_rxfifo funcs as per Frieder review comments Changes for v6:
- Rebase on top of v5.0-rc1
- Updated as per Frieder review comments and perform code cleanup
- Updated _fill_txfifo/_read_rxfifo func write/read logic Changes for v5:
- Rebase on top of v4.20-rc2
- Modifiedfspi_readl_poll_tout()as per review comments
- Arrange header file in alphabetical order
- Removed usage of read()/write() function callback pointer
- Add support for 1 and 2 byte address length
- Change Frieder e-mail to new e-mail address Changes for v4:
- Incorporate Boris review comments
* Usereadl_poll_timeout()instead of busy looping.
* Re-define register masking as per comment.
* Dropfspi_devtypeenum.
Changes for v3:
- Added endianness flag in platform specific structure instead of DTS.
- Modifiednxp_fspi_read_ahb(), removed remapping code.
- Added Boris and Frieder as Author and provided reference ofspi-fsl-qspi.cChanges for v2:
- Incorporated Boris review comments.
- Remove dependency of driver over connected flash device size.
- Modified the logic to select requested CS.
- Remove SPI-Octal Macros.drivers/spi/Kconfig | 10 + drivers/spi/Makefile | 1 + drivers/spi/spi-nxp-fspi.c | 1105 ++++++++++++++++++++++++++++++++++++ 3 files changed, 1116 insertions(+) create mode 100644 drivers/spi/spi-nxp-fspi.cdrivers/spi/Kconfig index renamed from drivers/spi/Kconfig +0
-0
dc67eda1788a..fc4cc7a65c33100644drivers/spi/Kconfig +10
-0@@ -279,6 +279,16 @@ config SPI_FSL_QUADSPI This controller does not support generic SPI messages. It only supports the high-level SPI memory interface. +config SPI_NXP_FLEXSPI + tristate "NXP Flex SPI controller" + depends on ARCH_LAYERSCAPE || HAS_IOMEM + help + This enables support for the Flex SPI controller in master mode. + Up to four slave devices can be connected on two buses with two + chipselects each. + This controller does not support generic SPI messages and only + supports the high-level SPI memory interface. + config SPI_GPIO tristate "GPIO-based bitbanging SPI Master" depends on GPIOLIB || COMPILE_TESTdrivers/spi/Makefile index renamed from drivers/spi/Makefile +0
-0
2a857cb9aa81..5c5af4676279100644drivers/spi/Makefile +1
-0@@ -64,6 +64,7 @@ obj-$(CONFIG_SPI_MXIC) += spi-mxic.o obj-$(CONFIG_SPI_MXS) += spi-mxs.o obj-$(CONFIG_SPI_NPCM_PSPI) += spi-npcm-pspi.o obj-$(CONFIG_SPI_NUC900) += spi-nuc900.o +obj-$(CONFIG_SPI_NXP_FLEXSPI) += spi-nxp-fspi.o obj-$(CONFIG_SPI_OC_TINY) += spi-oc-tiny.o spi-octeon-objs := spi-cavium.o spi-cavium-octeon.o obj-$(CONFIG_SPI_OCTEON) += spi-octeon.odrivers/spi/spi-nxp-fspi.c new file mode renamed from drivers/spi/spi-nxp-fspi.c +0
-0100644 index 000000000000..b8f19bab3b66
drivers/spi/spi-nxp-fspi.c new file +501
-0@@ -0,0 +1,1105 @@ +// SPDX-License-Identifier: GPL-2.0+ + +/* +* NXP FlexSPI(FSPI) controller driver. +* +* Copyright 2019 NXP. +* +* FlexSPI is a flexsible SPI host controller which supports two SPI +* channels and up to 4 external devices. Each channel supports +* Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional +* data lines). +* +* FlexSPI controller is driven by the LUT(Look-up Table) registers +* LUT registers are a look-up-table for sequences of instructions. +* A valid sequence consists of four LUT registers. +* Maximum 32 LUT sequences can be programmed simultaneously. +* +* LUTs are being created at run-time based on the commands passed +* from the spi-mem framework, thus using single LUT index. +* +* Software triggered Flash read/write access by IP Bus. +* +* Memory mapped read access by AHB Bus. +* +* Based on SPI MEM interface and spi-fsl-qspi.c driver. +* +* Author: +* Yogesh Narayan Gaur <[email protected]> +* Boris Brezillion <[email protected]> +* Frieder Schrempf <[email protected]> +*/ + +#include <linux/bitops.h> +#include <linux/clk.h> +#include <linux/completion.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/errno.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/iopoll.h> +#include <linux/jiffies.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/mutex.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/pm_qos.h> +#include <linux/sizes.h> + +#include <linux/spi/spi.h> +#include <linux/spi/spi-mem.h> + +/* +* The driver only uses one single LUT entry, that is updated on +* each call of exec_op(). Index 0 is preset at boot with a basic +* read operation, so let's use the last entry (31). +*/ +#define SEQID_LUT 31 + +/* Registers used by the driver */ +#define FSPI_MCR0 0x00 +#define FSPI_MCR0_AHB_TIMEOUT (x) ((x) << 24) +#define FSPI_MCR0_IP_TIMEOUT (x) ((x) << 16) +#define FSPI_MCR0_LEARN_EN BIT(15) +#define FSPI_MCR0_SCRFRUN_EN BIT(14) +#define FSPI_MCR0_OCTCOMB_EN BIT(13) +#define FSPI_MCR0_DOZE_EN BIT(12) +#define FSPI_MCR0_HSEN BIT(11) +#define FSPI_MCR0_SERCLKDIV BIT(8) +#define FSPI_MCR0_ATDF_EN BIT(7) +#define FSPI_MCR0_ARDF_EN BIT(6) +#define FSPI_MCR0_RXCLKSRC (x) ((x) << 4) +#define FSPI_MCR0_END_CFG (x) ((x) << 2) +#define FSPI_MCR0_MDIS BIT(1) +#define FSPI_MCR0_SWRST BIT(0) + +#define FSPI_MCR1 0x04 +#define FSPI_MCR1_SEQ_TIMEOUT (x) ((x) << 16) +#define FSPI_MCR1_AHB_TIMEOUT (x) (x) + +#define FSPI_MCR2 0x08 +#define FSPI_MCR2_IDLE_WAIT (x) ((x) << 24) +#define FSPI_MCR2_SAMEDEVICEEN BIT(15) +#define FSPI_MCR2_CLRLRPHS BIT(14) +#define FSPI_MCR2_ABRDATSZ BIT(8) +#define FSPI_MCR2_ABRLEARN BIT(7) +#define FSPI_MCR2_ABR_READ BIT(6) +#define FSPI_MCR2_ABRWRITE BIT(5) +#define FSPI_MCR2_ABRDUMMY BIT(4) +#define FSPI_MCR2_ABR_MODE BIT(3) +#define FSPI_MCR2_ABRCADDR BIT(2) +#define FSPI_MCR2_ABRRADDR BIT(1) +#define FSPI_MCR2_ABR_CMD BIT(0) + +#define FSPI_AHBCR 0x0c +#define FSPI_AHBCR_RDADDROPT BIT(6) +#define FSPI_AHBCR_PREF_EN BIT(5) +#define FSPI_AHBCR_BUFF_EN BIT(4) +#define FSPI_AHBCR_CACH_EN BIT(3) +#define FSPI_AHBCR_CLRTXBUF BIT(2) +#define FSPI_AHBCR_CLRRXBUF BIT(1) +#define FSPI_AHBCR_PAR_EN BIT(0) + +#define FSPI_INTEN 0x10 +#define FSPI_INTEN_SCLKSBWR BIT(9) +#define FSPI_INTEN_SCLKSBRD BIT(8) +#define FSPI_INTEN_DATALRNFL BIT(7) +#define FSPI_INTEN_IPTXWE BIT(6) +#define FSPI_INTEN_IPRXWA BIT(5) +#define FSPI_INTEN_AHBCMDERR BIT(4) +#define FSPI_INTEN_IPCMDERR BIT(3) +#define FSPI_INTEN_AHBCMDGE BIT(2) +#define FSPI_INTEN_IPCMDGE BIT(1) +#define FSPI_INTEN_IPCMDDONE BIT(0) + +#define FSPI_INTR 0x14 +#define FSPI_INTR_SCLKSBWR BIT(9) +#define FSPI_INTR_SCLKSBRD BIT(8) +#define FSPI_INTR_DATALRNFL BIT(7) +#define FSPI_INTR_IPTXWE BIT(6) +#define FSPI_INTR_IPRXWA BIT(5) +#define FSPI_INTR_AHBCMDERR BIT(4) +#define FSPI_INTR_IPCMDERR BIT(3) +#define FSPI_INTR_AHBCMDGE BIT(2) +#define FSPI_INTR_IPCMDGE BIT(1) +#define FSPI_INTR_IPCMDDONE BIT(0) + +#define FSPI_LUTKEY 0x18 +#define FSPI_LUTKEY_VALUE 0x5AF05AF0 + +#define FSPI_LCKCR 0x1C + +#define FSPI_LCKER_LOCK 0x1 +#define FSPI_LCKER_UNLOCK 0x2 + +#define FSPI_BUFXCR_INVALID_MSTRID 0xE +#define FSPI_AHBRX_BUF0CR0 0x20 +#define FSPI_AHBRX_BUF1CR0 0x24 +#define FSPI_AHBRX_BUF2CR0 0x28 +#define FSPI_AHBRX_BUF3CR0 0x2C +#define FSPI_AHBRX_BUF4CR0 0x30 +#define FSPI_AHBRX_BUF5CR0 0x34 +#define FSPI_AHBRX_BUF6CR0 0x38 +#define FSPI_AHBRX_BUF7CR0 0x3C +#define FSPI_AHBRXBUF0CR7_PREF BIT(31) + +#define FSPI_AHBRX_BUF0CR1 0x40 +#define FSPI_AHBRX_BUF1CR1 0x44 +#define FSPI_AHBRX_BUF2CR1 0x48 +#define FSPI_AHBRX_BUF3CR1 0x4C +#define FSPI_AHBRX_BUF4CR1 0x50 +#define FSPI_AHBRX_BUF5CR1 0x54 +#define FSPI_AHBRX_BUF6CR1 0x58 +#define FSPI_AHBRX_BUF7CR1 0x5C + +#define FSPI_FLSHA1CR0 0x60 +#define FSPI_FLSHA2CR0 0x64 +#define FSPI_FLSHB1CR0 0x68 +#define FSPI_FLSHB2CR0 0x6C +#define FSPI_FLSHXCR0_SZ_KB 10 +#define FSPI_FLSHXCR0_SZ (x) ((x) >> FSPI_FLSHXCR0_SZ_KB) + +#define FSPI_FLSHA1CR1 0x70 +#define FSPI_FLSHA2CR1 0x74 +#define FSPI_FLSHB1CR1 0x78 +#define FSPI_FLSHB2CR1 0x7C +#define FSPI_FLSHXCR1_CSINTR (x) ((x) << 16) +#define FSPI_FLSHXCR1_CAS (x) ((x) << 11) +#define FSPI_FLSHXCR1_WA BIT(10) +#define FSPI_FLSHXCR1_TCSH (x) ((x) << 5) +#define FSPI_FLSHXCR1_TCSS (x) (x) + +#define FSPI_FLSHA1CR2 0x80 +#define FSPI_FLSHA2CR2 0x84 +#define FSPI_FLSHB1CR2 0x88 +#define FSPI_FLSHB2CR2 0x8C +#define FSPI_FLSHXCR2_CLRINSP BIT(24) +#define FSPI_FLSHXCR2_AWRWAIT BIT(16) +#define FSPI_FLSHXCR2_AWRSEQN_SHIFT 13 +#define FSPI_FLSHXCR2_AWRSEQI_SHIFT 8 +#define FSPI_FLSHXCR2_ARDSEQN_SHIFT 5 +#define FSPI_FLSHXCR2_ARDSEQI_SHIFT 0 + +#define FSPI_IPCR0 0xA0 + +#define FSPI_IPCR1 0xA4 +#define FSPI_IPCR1_IPAREN BIT(31) +#define FSPI_IPCR1_SEQNUM_SHIFT 24 +#define FSPI_IPCR1_SEQID_SHIFT 16 +#define FSPI_IPCR1_IDATSZ (x) (x) + +#define FSPI_IPCMD 0xB0 +#define FSPI_IPCMD_TRG BIT(0) + +#define FSPI_DLPR 0xB4 + +#define FSPI_IPRXFCR 0xB8 +#define FSPI_IPRXFCR_CLR BIT(0) +#define FSPI_IPRXFCR_DMA_EN BIT(1) +#define FSPI_IPRXFCR_WMRK (x) ((x) << 2) + +#define FSPI_IPTXFCR 0xBC +#define FSPI_IPTXFCR_CLR BIT(0) +#define FSPI_IPTXFCR_DMA_EN BIT(1) +#define FSPI_IPTXFCR_WMRK (x) ((x) << 2) + +#define FSPI_DLLACR 0xC0 +#define FSPI_DLLACR_OVRDEN BIT(8) + +#define FSPI_DLLBCR 0xC4 +#define FSPI_DLLBCR_OVRDEN BIT(8) + +#define FSPI_STS0 0xE0 +#define FSPI_STS0_DLPHB (x) ((x) << 8) +#define FSPI_STS0_DLPHA (x) ((x) << 4) +#define FSPI_STS0_CMD_SRC (x) ((x) << 2) +#define FSPI_STS0_ARB_IDLE BIT(1) +#define FSPI_STS0_SEQ_IDLE BIT(0) + +#define FSPI_STS1 0xE4 +#define FSPI_STS1_IP_ERRCD (x) ((x) << 24) +#define FSPI_STS1_IP_ERRID (x) ((x) << 16) +#define FSPI_STS1_AHB_ERRCD (x) ((x) << 8) +#define FSPI_STS1_AHB_ERRID (x) (x) + +#define FSPI_AHBSPNST 0xEC +#define FSPI_AHBSPNST_DATLFT (x) ((x) << 16) +#define FSPI_AHBSPNST_BUFID (x) ((x) << 1) +#define FSPI_AHBSPNST_ACTIVE BIT(0) + +#define FSPI_IPRXFSTS 0xF0 +#define FSPI_IPRXFSTS_RDCNTR (x) ((x) << 16) +#define FSPI_IPRXFSTS_FILL (x) (x) + +#define FSPI_IPTXFSTS 0xF4 +#define FSPI_IPTXFSTS_WRCNTR (x) ((x) << 16) +#define FSPI_IPTXFSTS_FILL (x) (x) + +#define FSPI_RFDR 0x100 +#define FSPI_TFDR 0x180 + +#define FSPI_LUT_BASE 0x200 +#define FSPI_LUT_OFFSET (SEQID_LUT * 4 * 4) +#define FSPI_LUT_REG (idx) \ + (FSPI_LUT_BASE + FSPI_LUT_OFFSET + (idx) * 4) + +/* register map end */ + +/* Instruction set for the LUT register. */ +#define LUT_STOP 0x00 +#define LUT_CMD 0x01 +#define LUT_ADDR 0x02 +#define LUT_CADDR_SDR 0x03 +#define LUT_MODE 0x04 +#define LUT_MODE2 0x05 +#define LUT_MODE4 0x06 +#define LUT_MODE8 0x07 +#define LUT_NXP_WRITE 0x08 +#define LUT_NXP_READ 0x09 +#define LUT_LEARN_SDR 0x0A +#define LUT_DATSZ_SDR 0x0B +#define LUT_DUMMY 0x0C +#define LUT_DUMMY_RWDS_SDR 0x0D +#define LUT_JMP_ON_CS 0x1F +#define LUT_CMD_DDR 0x21 +#define LUT_ADDR_DDR 0x22 +#define LUT_CADDR_DDR 0x23 +#define LUT_MODE_DDR 0x24 +#define LUT_MODE2_DDR 0x25 +#define LUT_MODE4_DDR 0x26 +#define LUT_MODE8_DDR 0x27 +#define LUT_WRITE_DDR 0x28 +#define LUT_READ_DDR 0x29 +#define LUT_LEARN_DDR 0x2A +#define LUT_DATSZ_DDR 0x2B +#define LUT_DUMMY_DDR 0x2C +#define LUT_DUMMY_RWDS_DDR 0x2D + +/* +* Calculate number of required PAD bits for LUT register. +* +* The pad stands for the number of IO lines [0:7]. +* For example, the octal read needs eight IO lines, +* so you should use LUT_PAD(8). This macro +* returns 3 i.e. use eight (2^3) IP lines for read. +*/ +#define LUT_PAD (x) (fls(x) - 1) + +/* +* Macro for constructing the LUT entries with the following +* register layout: +* +* --------------------------------------------------- +* | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 | +* --------------------------------------------------- +*/ +#define PAD_SHIFT 8 +#define INSTR_SHIFT 10 +#define OPRND_SHIFT 16 + +/* Macros for constructing the LUT register. */ +#define LUT_DEF (idx, ins, pad, opr) \ + ((((ins) << INSTR_SHIFT) | ((pad) << PAD_SHIFT) | \ + (opr)) << (((idx) % 2) * OPRND_SHIFT)) + +#define POLL_TOUT 5000 +#define NXP_FSPI_MAX_CHIPSELECT 4 + +struct nxp_fspi_devtype_data { +unsigned int rxfifo; +unsigned int txfifo; +unsigned int ahb_buf_size; +unsigned int quirks; +bool little_endian; +}; + +static const struct nxp_fspi_devtype_data lx2160a_data = { + .rxfifo =SZ_512 ,/* (64 * 64 bits) */ + .txfifo =SZ_1K ,/* (128 * 64 bits) */ + .ahb_buf_size =SZ_2K ,/* (256 * 64 bits) */ + .quirks =0 , + .little_endian = true,/* little-endian */ +}; + +struct nxp_fspi { +void __iomem *iobase; +void __iomem *ahb_addr; +u32 memmap_phy; +u32 memmap_phy_size; +struct clk *clk, *clk_en; +struct device *dev; +struct completion c; +const struct nxp_fspi_devtype_data *devtype_data; +struct mutex lock; +struct pm_qos_request pm_qos_req; +int selected; +}; + +/* +* R/W functions for big- or little-endian registers: +* The FSPI controller's endianness is independent of +* the CPU core's endianness. So far, although the CPU +* core is little-endian the FSPI controller can use +* big-endian or little-endian. +*/ +static void fspi_writel (struct nxp_fspi *f,u32 val,void __iomem +*addr) { +if (f->devtype_data->little_endian) +iowrite32 (val, addr); +else +iowrite32be (val, addr); +} + +static u32 fspi_readl (struct nxp_fspi *f,void __iomem *addr) { +if (f->devtype_data->little_endian) +return ioread32 (addr); +else +return ioread32be (addr); +} + +static irqreturn_t nxp_fspi_irq_handler (int irq,void *dev_id) { +struct nxp_fspi *f = dev_id; +u32 reg; + +/* clear interrupt */ + reg =fspi_readl (f, f->iobase +FSPI_INTR ); +fspi_writel (f,FSPI_INTR_IPCMDDONE , f->iobase +FSPI_INTR ); + +if (reg &FSPI_INTR_IPCMDDONE ) +complete (&f->c); + +return IRQ_HANDLED ; +} + +static int nxp_fspi_check_buswidth (struct nxp_fspi *f,u8 width) { +switch (width) { +case 1 : +case 2 : +case 4 : +case 8 : +return 0 ; + } + +return -ENOTSUPP ; +} + +static bool nxp_fspi_supports_op (struct spi_mem *mem, +const struct spi_mem_op *op) +{ +struct nxp_fspi *f =spi_controller_get_devdata (mem->spi->master); +int ret; + + ret =nxp_fspi_check_buswidth (f, op->cmd.buswidth); + +if (op->addr.nbytes) + ret |=nxp_fspi_check_buswidth (f, op->addr.buswidth); + +if (op->dummy.nbytes) + ret |=nxp_fspi_check_buswidth (f, op->dummy.buswidth); + +if (op->data.nbytes) + ret |=nxp_fspi_check_buswidth (f, op->data.buswidth); + +if (ret) +return false; + +/* +* The number of address bytes should be equal to or less than 4 bytes. +*/ +if (op->addr.nbytes >4 ) +return false; + +/* +* If requested address value is greater than controller assigned +* memory mapped space, return error as it didn't fit in the range +* of assigned address space. +*/ +if (op->addr.val >= f->memmap_phy_size) +return false; + +/* Max 64 dummy clock cycles supported */ +if (op->dummy.buswidth && + (op->dummy.nbytes *8 / op->dummy.buswidth >64 )) +return false; + +/* Max data length, check controller limits and alignment */ +if (op->data.dir ==SPI_MEM_DATA_IN && + (op->data.nbytes > f->devtype_data->ahb_buf_size || + (op->data.nbytes > f->devtype_data->rxfifo -4 && + !IS_ALIGNED (op->data.nbytes,8 )))) +return false; + +if (op->data.dir ==SPI_MEM_DATA_OUT && + op->data.nbytes > f->devtype_data->txfifo) +return false; + +return true; +} + +/* Instead of busy looping invoke readl_poll_timeout functionality. */ +static int fspi_readl_poll_tout (struct nxp_fspi *f,void __iomem *base, +u32 mask,u32 delay_us, +u32 timeout_us,bool c) +{ +u32 reg; + +if (!f->devtype_data->little_endian) + mask = (u32 )cpu_to_be32 (mask); + +if (c) +return readl_poll_timeout (base, reg, (reg & mask), + delay_us, timeout_us); +else +return readl_poll_timeout (base, reg, !(reg & mask), + delay_us, timeout_us); +} + +/* +* If the slave device content being changed by Write/Erase, need to +* invalidate the AHB buffer. This can be achieved by doing the reset +* of controller after setting MCR0[SWRESET] bit. +*/ +static inline void nxp_fspi_invalid (struct nxp_fspi *f) { +u32 reg; +int ret; + + reg =fspi_readl (f, f->iobase +FSPI_MCR0 ); +fspi_writel (f, reg |FSPI_MCR0_SWRST , f->iobase +FSPI_MCR0 ); + +/* w1c register, wait unit clear */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_MCR0 , +FSPI_MCR0_SWRST ,0 ,POLL_TOUT , false); +WARN_ON (ret); +} + +static void nxp_fspi_prepare_lut (struct nxp_fspi *f, +const struct spi_mem_op *op) +{ +void __iomem *base = f->iobase; +u32 lutval[4 ] = {}; +int lutidx =1 , i; + +/* cmd */ + lutval[0 ] |=LUT_DEF (0 ,LUT_CMD ,LUT_PAD (op->cmd.buswidth), + op->cmd.opcode); + +/* addr bytes */ +if (op->addr.nbytes) { + lutval[lutidx /2 ] |=LUT_DEF (lutidx,LUT_ADDR , +LUT_PAD (op->addr.buswidth), + op->addr.nbytes *8 ); + lutidx++; + } + +/* dummy bytes, if needed */ +if (op->dummy.nbytes) { + lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_DUMMY, +/* +* Due to FlexSPI controller limitation number of PAD for dummy
drivers/spi/spi-nxp-fspi.c new file +12
-0+* buswidth needs to be programmed as equal to data buswidth. +*/ +LUT_PAD (op->data.buswidth), + op->dummy.nbytes *8 / + op->dummy.buswidth); + lutidx++; + } + +/* read/write data bytes */ +if (op->data.nbytes) { + lutval[lutidx / 2] |= LUT_DEF(lutidx, + op->data.dir ==
SPI_MEM_DATA_IN?drivers/spi/spi-nxp-fspi.c new file +359
-0+ LUT_NXP_READ :LUT_NXP_WRITE , +LUT_PAD (op->data.buswidth), + 0); + lutidx++; + } + +/* stop condition. */ + lutval[lutidx /2 ] |=LUT_DEF (lutidx,LUT_STOP ,0 ,0 ); + +/* unlock LUT */ +fspi_writel (f,FSPI_LUTKEY_VALUE , f->iobase +FSPI_LUTKEY ); +fspi_writel (f,FSPI_LCKER_UNLOCK , f->iobase +FSPI_LCKCR ); + +/* fill LUT */ +for (i =0 ; i <ARRAY_SIZE (lutval); i++) +fspi_writel (f, lutval[i], base +FSPI_LUT_REG (i)); + +dev_dbg (f->dev,"CMD[%x] lutval[0:%x \t 1:%x \t 2:%x \t 3:%x]\n" , + op->cmd.opcode, lutval[0 ], lutval[1 ], lutval[2 ], lutval[3 ]); + +/* lock LUT */ +fspi_writel (f,FSPI_LUTKEY_VALUE , f->iobase +FSPI_LUTKEY ); +fspi_writel (f,FSPI_LCKER_LOCK , f->iobase +FSPI_LCKCR ); } + +static int nxp_fspi_clk_prep_enable (struct nxp_fspi *f) { +int ret; + + ret =clk_prepare_enable (f->clk_en); +if (ret) +return ret; + + ret =clk_prepare_enable (f->clk); +if (ret) { +clk_disable_unprepare (f->clk_en); +return ret; + } + +return 0 ; +} + +static void nxp_fspi_clk_disable_unprep (struct nxp_fspi *f) { +clk_disable_unprepare (f->clk); +clk_disable_unprepare (f->clk_en); +} + +/* +* In FlexSPI controller, flash access is based on value of +FSPI_FLSHXXCR0 +* register and start base address of the slave device. +* +* (Higher address) +* -------- <-- FLSHB2CR0 +* | B2 | +* | | +* B2 start address --> -------- <-- FLSHB1CR0 +* | B1 | +* | | +* B1 start address --> -------- <-- FLSHA2CR0 +* | A2 | +* | | +* A2 start address --> -------- <-- FLSHA1CR0 +* | A1 | +* | | +* A1 start address --> -------- (Lower address) +* +* +* Start base address defines the starting address range for given CS +and +* FSPI_FLSHXXCR0 defines the size of the slave device connected at given CS. +* +* But, different targets are having different combinations of number +of CS, +* some targets only have single CS or two CS covering controller's +full +* memory mapped space area. +* Thus, implementation is being done as independent of the size and +number +* of the connected slave device. +* Assign controller memory mapped space size as the size to the +connected +* slave device. +* Mark FLSHxxCR0 as zero initially and then assign value only to the +selected +* chip-select Flash configuration register. +* +* For e.g. to access CS2 (B1), FLSHB1CR0 register would be equal to +the +* memory mapped size of the controller. +* Value for rest of the CS FLSHxxCR0 register would be zero. +* +*/ +static void nxp_fspi_select_mem (struct nxp_fspi *f,struct spi_device +*spi) { +unsigned long rate = spi->max_speed_hz; +int ret; +uint64_t size_kb; + +/* +* Return, if previously selected slave device is same as current +* requested slave device. +*/ +if (f->selected == spi->chip_select) +return ; + +/* Reset FLSHxxCR0 registers */ +fspi_writel (f,0 , f->iobase +FSPI_FLSHA1CR0 ); +fspi_writel (f,0 , f->iobase +FSPI_FLSHA2CR0 ); +fspi_writel (f,0 , f->iobase +FSPI_FLSHB1CR0 ); +fspi_writel (f,0 , f->iobase +FSPI_FLSHB2CR0 ); + +/* Assign controller memory mapped space as size, KBytes, of flash. */ + size_kb =FSPI_FLSHXCR0_SZ (f->memmap_phy_size); + +fspi_writel (f, size_kb, f->iobase +FSPI_FLSHA1CR0 + +4 * spi->chip_select); + +dev_dbg (f->dev,"Slave device [CS:%x] selected\n" , spi->chip_select); + +nxp_fspi_clk_disable_unprep (f); + + ret =clk_set_rate (f->clk, rate); +if (ret) +return ; + + ret =nxp_fspi_clk_prep_enable (f); +if (ret) +return ; + + f->selected = spi->chip_select; +} + +static void nxp_fspi_read_ahb (struct nxp_fspi *f,const struct +spi_mem_op *op) { +u32 len = op->data.nbytes; + +/* Read out the data directly from the AHB buffer. */ +memcpy_fromio (op->data.buf.in, (f->ahb_addr + op->addr.val), len); } + +static void nxp_fspi_fill_txfifo (struct nxp_fspi *f, +const struct spi_mem_op *op) +{ +void __iomem *base = f->iobase; +int i, ret; +u8 *buf = (u8 *) op->data.buf.out; + +/* clear the TX FIFO. */ +fspi_writel (f,FSPI_IPTXFCR_CLR , base +FSPI_IPTXFCR ); + +/* +* Default value of water mark level is 8 bytes, hence in single +* write request controller can write max 8 bytes of data. +*/ + +for (i =0 ; i <ALIGN_DOWN (op->data.nbytes,8 ); i +=8 ) { +/* Wait for TXFIFO empty */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_INTR , +FSPI_INTR_IPTXWE ,0 , +POLL_TOUT , true); +WARN_ON (ret); + +fspi_writel (f, *(u32 *) (buf + i), base +FSPI_TFDR ); +fspi_writel (f, *(u32 *) (buf + i +4 ), base +FSPI_TFDR +4 ); +fspi_writel (f,FSPI_INTR_IPTXWE , base +FSPI_INTR ); + } + +if (i < op->data.nbytes) { +u32 data =0 ; +int j; +/* Wait for TXFIFO empty */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_INTR , +FSPI_INTR_IPTXWE ,0 , +POLL_TOUT , true); +WARN_ON (ret); + +for (j =0 ; j <ALIGN (op->data.nbytes - i,4 ); j +=4 ) { +memcpy (&data, buf + i + j,4 ); +fspi_writel (f, data, base +FSPI_TFDR + j); + } +fspi_writel (f,FSPI_INTR_IPTXWE , base +FSPI_INTR ); + } +} + +static void nxp_fspi_read_rxfifo (struct nxp_fspi *f, +const struct spi_mem_op *op) +{ +void __iomem *base = f->iobase; +int i, ret; +int len = op->data.nbytes; +u8 *buf = (u8 *) op->data.buf.in; + +/* +* Default value of water mark level is 8 bytes, hence in single +* read request controller can read max 8 bytes of data. +*/ +for (i =0 ; i <ALIGN_DOWN (len,8 ); i +=8 ) { +/* Wait for RXFIFO available */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_INTR , +FSPI_INTR_IPRXWA ,0 , +POLL_TOUT , true); +WARN_ON (ret); + + *(u32 *)(buf + i) =fspi_readl (f, base +FSPI_RFDR ); + *(u32 *)(buf + i +4 ) =fspi_readl (f, base +FSPI_RFDR +4 ); +/* move the FIFO pointer */ +fspi_writel (f,FSPI_INTR_IPRXWA , base +FSPI_INTR ); + } + +if (i < len) { +u32 tmp; +int size, j; + + buf = op->data.buf.in + i; +/* Wait for RXFIFO available */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_INTR , +FSPI_INTR_IPRXWA ,0 , +POLL_TOUT , true); +WARN_ON (ret); + + len = op->data.nbytes - i; +for (j =0 ; j < op->data.nbytes - i; j +=4 ) { + tmp =fspi_readl (f, base +FSPI_RFDR + j); + size =min (len,4 ); +memcpy (buf + j, &tmp, size); + len -= size; + } + } + +/* invalid the RXFIFO */ +fspi_writel (f,FSPI_IPRXFCR_CLR , base +FSPI_IPRXFCR ); +/* move the FIFO pointer */ +fspi_writel (f,FSPI_INTR_IPRXWA , base +FSPI_INTR ); } + +static int nxp_fspi_do_op (struct nxp_fspi *f,const struct spi_mem_op +*op) { +void __iomem *base = f->iobase; +int seqnum =0 ; +int err =0 ; +u32 reg; + + reg =fspi_readl (f, base +FSPI_IPRXFCR ); +/* invalid RXFIFO first */ + reg &= ~FSPI_IPRXFCR_DMA_EN ; + reg = reg |FSPI_IPRXFCR_CLR ; +fspi_writel (f, reg, base +FSPI_IPRXFCR ); + +init_completion (&f->c); + +fspi_writel (f, op->addr.val, base +FSPI_IPCR0 ); +/* +* Always start the sequence at the same index since we update +* the LUT at each exec_op() call. And also specify the DATA +* length, since it's has not been specified in the LUT. +*/ +fspi_writel (f, op->data.nbytes | + (SEQID_LUT <<FSPI_IPCR1_SEQID_SHIFT ) | + (seqnum <<FSPI_IPCR1_SEQNUM_SHIFT ), + base +FSPI_IPCR1 ); + +/* Trigger the LUT now. */ +fspi_writel (f,FSPI_IPCMD_TRG , base +FSPI_IPCMD ); + +/* Wait for the interrupt. */ +if (!wait_for_completion_timeout (&f->c,msecs_to_jiffies (1000 ))) + err = -ETIMEDOUT ; + +/* Invoke IP data read, if request is of data read. */ +if (!err && op->data.nbytes && op->data.dir ==SPI_MEM_DATA_IN ) +nxp_fspi_read_rxfifo (f, op); + +return err; +} + +static int nxp_fspi_exec_op (struct spi_mem *mem,const struct +spi_mem_op *op) { +struct nxp_fspi *f =spi_controller_get_devdata (mem->spi->master); +int err =0 ; + +mutex_lock (&f->lock); + +/* Wait for controller being ready. */ + err =fspi_readl_poll_tout (f, f->iobase +FSPI_STS0 , +FSPI_STS0_ARB_IDLE ,1 ,POLL_TOUT , true); +WARN_ON (err); + +nxp_fspi_select_mem (f, mem->spi); + +nxp_fspi_prepare_lut (f, op); +/* +* If we have large chunks of data, we read them through the AHB bus +* by accessing the mapped memory. In all other cases we use +* IP commands to access the flash. +*/ +if (op->data.nbytes > (f->devtype_data->rxfifo -4 ) && + op->data.dir ==SPI_MEM_DATA_IN ) { +nxp_fspi_read_ahb (f, op); + }else { +if (op->data.nbytes && op->data.dir ==SPI_MEM_DATA_OUT ) +nxp_fspi_fill_txfifo (f, op); + + err =nxp_fspi_do_op (f, op); + } + +/* Invalidate the data in the AHB buffer. */ +nxp_fspi_invalid (f); + +mutex_unlock (&f->lock); + +return err; +} + +static int nxp_fspi_adjust_op_size (struct spi_mem *mem,struct +spi_mem_op *op) { +struct nxp_fspi *f =spi_controller_get_devdata (mem->spi->master); + +if (op->data.dir ==SPI_MEM_DATA_OUT ) { +if (op->data.nbytes > f->devtype_data->txfifo) + op->data.nbytes = f->devtype_data->txfifo; + }else { +if (op->data.nbytes > f->devtype_data->ahb_buf_size) + op->data.nbytes = f->devtype_data->ahb_buf_size; +else if (op->data.nbytes > (f->devtype_data->rxfifo -4 )) + op->data.nbytes =ALIGN_DOWN (op->data.nbytes,8 ); + } + +return 0 ; +} + +static int nxp_fspi_default_setup (struct nxp_fspi *f) { +void __iomem *base = f->iobase; +int ret, i; +u32 reg; + +/* disable and unprepare clock to avoid glitch pass to controller */ +nxp_fspi_clk_disable_unprep (f); + +/* the default frequency, we will change it later if necessary. */ + ret =clk_set_rate (f->clk,20000000 ); +if (ret) +return ret; + + ret =nxp_fspi_clk_prep_enable (f); +if (ret) +return ret; + +/* Reset the module */ +/* w1c register, wait unit clear */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_MCR0 , +FSPI_MCR0_SWRST ,0 ,POLL_TOUT , false); +WARN_ON (ret); + +/* Disable the module */ +fspi_writel (f,FSPI_MCR0_MDIS , base +FSPI_MCR0 ); + +/* Reset the DLL register to default value */ +fspi_writel (f,FSPI_DLLACR_OVRDEN , base +FSPI_DLLACR ); +fspi_writel (f,FSPI_DLLBCR_OVRDEN , base +FSPI_DLLBCR ); + +/* enable module */ + fspi_writel(f, FSPI_MCR0_AHB_TIMEOUT(0xFF) |
FSPI_MCR0_IP_TIMEOUT(0xFF),drivers/spi/spi-nxp-fspi.c new file +94
-0+ base + FSPI_MCR0); + +/* +* Disable same device enable bit and configure all slave devices +* independently. +*/ + reg =fspi_readl (f, f->iobase +FSPI_MCR2 ); + reg = reg & ~(FSPI_MCR2_SAMEDEVICEEN ); +fspi_writel (f, reg, base +FSPI_MCR2 ); + +/* AHB configuration for access buffer 0~7. */ +for (i =0 ; i <7 ; i++) +fspi_writel (f,0 , base +FSPI_AHBRX_BUF0CR0 +4 * i); + +/* +* Set ADATSZ with the maximum AHB buffer size to improve the read +* performance. +*/ +fspi_writel (f, (f->devtype_data->ahb_buf_size /8 | +FSPI_AHBRXBUF0CR7_PREF ), base +FSPI_AHBRX_BUF7CR0 ); + +/* prefetch and no start address alignment limitation */ +fspi_writel (f,FSPI_AHBCR_PREF_EN |FSPI_AHBCR_RDADDROPT , + base +FSPI_AHBCR ); + +/* AHB Read - Set lut sequence ID for all CS. */ +fspi_writel (f,SEQID_LUT , base +FSPI_FLSHA1CR2 ); +fspi_writel (f,SEQID_LUT , base +FSPI_FLSHA2CR2 ); +fspi_writel (f,SEQID_LUT , base +FSPI_FLSHB1CR2 ); +fspi_writel (f,SEQID_LUT , base +FSPI_FLSHB2CR2 ); + + f->selected =-1 ; + +/* enable the interrupt */ +fspi_writel (f,FSPI_INTEN_IPCMDDONE , base +FSPI_INTEN ); + +return 0 ; +} + +static const char *nxp_fspi_get_name (struct spi_mem *mem) { +struct nxp_fspi *f =spi_controller_get_devdata (mem->spi->master); +struct device *dev = &mem->spi->dev; +const char *name; + +// Set custom name derived from the platform_device of the controller. +if (of_get_available_child_count (f->dev->of_node) ==1 ) +return dev_name (f->dev); + + name =devm_kasprintf (dev,GFP_KERNEL , +"%s-%d" ,dev_name (f->dev), + mem->spi->chip_select); + +if (!name) { +dev_err (dev,"failed to get memory for custom flash name\n" ); +return ERR_PTR (-ENOMEM ); + } + +return name; +} + +static const struct spi_controller_mem_ops nxp_fspi_mem_ops = { + .adjust_op_size = nxp_fspi_adjust_op_size, + .supports_op = nxp_fspi_supports_op, + .exec_op = nxp_fspi_exec_op, + .get_name = nxp_fspi_get_name, +}; + +static int nxp_fspi_probe (struct platform_device *pdev) { +struct spi_controller *ctlr; +struct device *dev = &pdev->dev; +struct device_node *np = dev->of_node; +struct resource *res; +struct nxp_fspi *f; +int ret; + + ctlr =spi_alloc_master (&pdev->dev,sizeof (*f)); +if (!ctlr) +return -ENOMEM ; + + ctlr->mode_bits =SPI_RX_DUAL |SPI_RX_QUAD | +SPI_TX_DUAL |SPI_TX_QUAD ; + + f =spi_controller_get_devdata (ctlr); + f->dev = dev; + f->devtype_data =of_device_get_match_data (dev); +if (!f->devtype_data) { + ret = -ENODEV ; + goto err_put_ctrl; + } + +platform_set_drvdata (pdev, f); + +/* find the resources - configuration register address space */ + res = platform_get_resource_byname(pdev, IORESOURCE_MEM,"
fspi_base");drivers/spi/spi-nxp-fspi.c new file +8
-0+ f->iobase =devm_ioremap_resource (dev, res); +if (IS_ERR (f->iobase)) { + ret =PTR_ERR (f->iobase); + goto err_put_ctrl; + } + +/* find the resources - controller memory mapped space */ + res = platform_get_resource_byname(pdev, IORESOURCE_MEM,"
fspi_mmap");drivers/spi/spi-nxp-fspi.c new file +120
-0+ f->ahb_addr =devm_ioremap_resource (dev, res); +if (IS_ERR (f->ahb_addr)) { + ret =PTR_ERR (f->ahb_addr); + goto err_put_ctrl; + } + +/* assign memory mapped starting address and mapped size. */ + f->memmap_phy = res->start; + f->memmap_phy_size =resource_size (res); + +/* find the clocks */ + f->clk_en =devm_clk_get (dev,"fspi_en" ); +if (IS_ERR (f->clk_en)) { + ret =PTR_ERR (f->clk_en); + goto err_put_ctrl; + } + + f->clk =devm_clk_get (dev,"fspi" ); +if (IS_ERR (f->clk)) { + ret =PTR_ERR (f->clk); + goto err_put_ctrl; + } + + ret =nxp_fspi_clk_prep_enable (f); +if (ret) { +dev_err (dev,"can not enable the clock\n" ); + goto err_put_ctrl; + } + +/* find the irq */ + ret =platform_get_irq (pdev,0 ); +if (ret <0 ) { +dev_err (dev,"failed to get the irq: %d\n" , ret); + goto err_disable_clk; + } + + ret =devm_request_irq (dev, ret, + nxp_fspi_irq_handler,0 , pdev->name, f); +if (ret) { +dev_err (dev,"failed to request irq: %d\n" , ret); + goto err_disable_clk; + } + +mutex_init (&f->lock); + + ctlr->bus_num =-1 ; + ctlr->num_chipselect =NXP_FSPI_MAX_CHIPSELECT ; + ctlr->mem_ops = &nxp_fspi_mem_ops; + +nxp_fspi_default_setup (f); + + ctlr->dev.of_node = np; + + ret =spi_register_controller (ctlr); +if (ret) + goto err_destroy_mutex; + +return 0 ; + +err_destroy_mutex: +mutex_destroy (&f->lock); + +err_disable_clk: +nxp_fspi_clk_disable_unprep (f); + +err_put_ctrl: +spi_controller_put (ctlr); + +dev_err (dev,"NXP FSPI probe failed\n" ); +return ret; +} + +static int nxp_fspi_remove (struct platform_device *pdev) { +struct nxp_fspi *f =platform_get_drvdata (pdev); + +/* disable the hardware */ +fspi_writel (f,FSPI_MCR0_MDIS , f->iobase +FSPI_MCR0 ); + +nxp_fspi_clk_disable_unprep (f); + +mutex_destroy (&f->lock); + +return 0 ; +} + +static int nxp_fspi_suspend (struct device *dev) { +return 0 ; +} + +static int nxp_fspi_resume (struct device *dev) { +struct nxp_fspi *f =dev_get_drvdata (dev); + +nxp_fspi_default_setup (f); + +return 0 ; +} + +static const struct of_device_id nxp_fspi_dt_ids[] = { + { .compatible ="nxp,lx2160a-fspi" , .data = (void *)&lx2160a_data, }, + {/* sentinel */ } +}; +MODULE_DEVICE_TABLE (of, nxp_fspi_dt_ids); + +static const struct dev_pm_ops nxp_fspi_pm_ops = { + .suspend = nxp_fspi_suspend, + .resume = nxp_fspi_resume, +}; + +static struct platform_driver nxp_fspi_driver = { + .driver = { + .name ="nxp-fspi" , + .of_match_table = nxp_fspi_dt_ids, + .pm = &nxp_fspi_pm_ops, + }, + .probe = nxp_fspi_probe, + .remove = nxp_fspi_remove, +}; +module_platform_driver (nxp_fspi_driver); + +MODULE_DESCRIPTION ("NXP FSPI Controller Driver" );MODULE_AUTHOR("NXP
+Semiconductor");MODULE_AUTHOR("Yogesh Narayan Gaur +<[email protected]>");MODULE_AUTHOR("Boris Brezillion +<[email protected]>");MODULE_AUTHOR("Frieder Schrempf +<[email protected]>");MODULE_LICENSE("GPL v2"); --
2.17.1
Mark Brown
maintainerQuoted 4 lines · Yogesh Narayan Gaur
Hello Mark,
Can you please apply below patch in SPI tree?
Patch has been reviewed by Boris and Frieder.
Please don't send content free pings and please allow a reasonable time for review. People get busy, go on holiday, attend conferences and so on so unless there is some reason for urgency (like critical bug fixes) please allow at least a couple of weeks for review. If there have been review comments then people may be waiting for those to be addressed.
Sending content free pings adds to the mail volume (if they are seen at all) which is often the problem and since they can't be reviewed directly if something has gone wrong you'll have to resend the patches anyway, so sending again is generally a better approach though there are some other maintainers who like them - if in doubt look at how patches for the subsystem are normally handled.
Quoted 40 lines
-----Original Message-----
From: linux-mtd <[email protected]> On Behalf Of Yogesh Narayan Gaur
Sent: Tuesday, January 15, 2019 5:30 PM
To: [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]
Cc: [email protected]; [email protected]; Yogesh Narayan Gaur <[email protected]>; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]
Subject: [PATCH v8 1/5] spi: spi-mem: Add driver for NXP FlexSPI controller- Add driver for NXP FlexSPI host controller
(0) What is the FlexSPI controller?
FlexSPI is a flexsible SPI host controller which supports two SPI channels and up
to 4 external devices. Each channel supports Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional data lines) i.e. FlexSPI acts as an interface to external devices, maximum 4, each with up to 8 bidirectional data lines.It uses new SPI memory interface of the SPI framework to issue flash memory
operations to up to four connected flash devices (2 buses with 2 CS each).(1) Tested this driver with the
mtd_debugand JFFS2 filesystem utility on NXP LX2160ARDB and LX2160AQDS targets.
LX2160ARDB is having two NOR slave device connected on single bus A i.e. A0
and A1 (CS0 and CS1).
LX2160AQDS is having two NOR slave device connected on separate buses one
flash on A0 and second on B1 i.e. (CS0 and CS3).
Verified this driver on following SPI NOR flashes:Micron, mt35xu512ab, [Read - 1 bit mode] Cypress, s25fl512s, [Read - 1/2/4 bit mode]Signed-off-by Yogesh Narayan Gaur <[email protected]>Reviewed-by Frieder Schrempf <[email protected]>Reviewed-by Boris Brezillon <[email protected]>
Quoted 6 lines
---
Changes for v8:
- Typo review comments changes
- Fix logic of read data for case when read size is less than 8 bytes.
- Add correct email address of Boris
- Add r-o-b tag of Frieder and Boris
Tested on LX2160ARDB in 1-bit mode for read, write and erase
Regards
Ashish
Quoted 1,187 lines
Changes for v7:
- Add func pointer for '.get_name' for structspi_controller_mem_ops
- Add input address range check as per controller memory mapped space
- Update _fill_txfifo/_read_rxfifo funcs as per Frieder review comments Changes for v6:
- Rebase on top of v5.0-rc1
- Updated as per Frieder review comments and perform code cleanup
- Updated _fill_txfifo/_read_rxfifo func write/read logic Changes for v5:
- Rebase on top of v4.20-rc2
- Modifiedfspi_readl_poll_tout()as per review comments
- Arrange header file in alphabetical order
- Removed usage of read()/write() function callback pointer
- Add support for 1 and 2 byte address length
- Change Frieder e-mail to new e-mail address Changes for v4:
- Incorporate Boris review comments
* Usereadl_poll_timeout()instead of busy looping.
* Re-define register masking as per comment.
* Dropfspi_devtypeenum.
Changes for v3:
- Added endianness flag in platform specific structure instead of DTS.
- Modifiednxp_fspi_read_ahb(), removed remapping code.
- Added Boris and Frieder as Author and provided reference ofspi-fsl-qspi.cChanges for v2:
- Incorporated Boris review comments.
- Remove dependency of driver over connected flash device size.
- Modified the logic to select requested CS.
- Remove SPI-Octal Macros.drivers/spi/Kconfig | 10 + drivers/spi/Makefile | 1 + drivers/spi/spi-nxp-fspi.c | 1105 ++++++++++++++++++++++++++++++++++++ 3 files changed, 1116 insertions(+) create mode 100644 drivers/spi/spi-nxp-fspi.cdrivers/spi/Kconfig index renamed from drivers/spi/Kconfig +0
-0
dc67eda1788a..fc4cc7a65c33100644drivers/spi/Kconfig +10
-0@@ -279,6 +279,16 @@ config SPI_FSL_QUADSPI This controller does not support generic SPI messages. It only supports the high-level SPI memory interface. +config SPI_NXP_FLEXSPI + tristate "NXP Flex SPI controller" + depends on ARCH_LAYERSCAPE || HAS_IOMEM + help + This enables support for the Flex SPI controller in master mode. + Up to four slave devices can be connected on two buses with two + chipselects each. + This controller does not support generic SPI messages and only + supports the high-level SPI memory interface. + config SPI_GPIO tristate "GPIO-based bitbanging SPI Master" depends on GPIOLIB || COMPILE_TESTdrivers/spi/Makefile index renamed from drivers/spi/Makefile +0
-0
2a857cb9aa81..5c5af4676279100644drivers/spi/Makefile +1
-0@@ -64,6 +64,7 @@ obj-$(CONFIG_SPI_MXIC) += spi-mxic.o obj-$(CONFIG_SPI_MXS) += spi-mxs.o obj-$(CONFIG_SPI_NPCM_PSPI) += spi-npcm-pspi.o obj-$(CONFIG_SPI_NUC900) += spi-nuc900.o +obj-$(CONFIG_SPI_NXP_FLEXSPI) += spi-nxp-fspi.o obj-$(CONFIG_SPI_OC_TINY) += spi-oc-tiny.o spi-octeon-objs := spi-cavium.o spi-cavium-octeon.o obj-$(CONFIG_SPI_OCTEON) += spi-octeon.odrivers/spi/spi-nxp-fspi.c new file mode renamed from drivers/spi/spi-nxp-fspi.c +0
-0100644 index 000000000000..b8f19bab3b66
drivers/spi/spi-nxp-fspi.c new file +501
-0@@ -0,0 +1,1105 @@ +// SPDX-License-Identifier: GPL-2.0+ + +/* +* NXP FlexSPI(FSPI) controller driver. +* +* Copyright 2019 NXP. +* +* FlexSPI is a flexsible SPI host controller which supports two SPI +* channels and up to 4 external devices. Each channel supports +* Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional +* data lines). +* +* FlexSPI controller is driven by the LUT(Look-up Table) registers +* LUT registers are a look-up-table for sequences of instructions. +* A valid sequence consists of four LUT registers. +* Maximum 32 LUT sequences can be programmed simultaneously. +* +* LUTs are being created at run-time based on the commands passed +* from the spi-mem framework, thus using single LUT index. +* +* Software triggered Flash read/write access by IP Bus. +* +* Memory mapped read access by AHB Bus. +* +* Based on SPI MEM interface and spi-fsl-qspi.c driver. +* +* Author: +* Yogesh Narayan Gaur <[email protected]> +* Boris Brezillion <[email protected]> +* Frieder Schrempf <[email protected]> +*/ + +#include <linux/bitops.h> +#include <linux/clk.h> +#include <linux/completion.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/errno.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/iopoll.h> +#include <linux/jiffies.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/mutex.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/pm_qos.h> +#include <linux/sizes.h> + +#include <linux/spi/spi.h> +#include <linux/spi/spi-mem.h> + +/* +* The driver only uses one single LUT entry, that is updated on +* each call of exec_op(). Index 0 is preset at boot with a basic +* read operation, so let's use the last entry (31). +*/ +#define SEQID_LUT 31 + +/* Registers used by the driver */ +#define FSPI_MCR0 0x00 +#define FSPI_MCR0_AHB_TIMEOUT (x) ((x) << 24) +#define FSPI_MCR0_IP_TIMEOUT (x) ((x) << 16) +#define FSPI_MCR0_LEARN_EN BIT(15) +#define FSPI_MCR0_SCRFRUN_EN BIT(14) +#define FSPI_MCR0_OCTCOMB_EN BIT(13) +#define FSPI_MCR0_DOZE_EN BIT(12) +#define FSPI_MCR0_HSEN BIT(11) +#define FSPI_MCR0_SERCLKDIV BIT(8) +#define FSPI_MCR0_ATDF_EN BIT(7) +#define FSPI_MCR0_ARDF_EN BIT(6) +#define FSPI_MCR0_RXCLKSRC (x) ((x) << 4) +#define FSPI_MCR0_END_CFG (x) ((x) << 2) +#define FSPI_MCR0_MDIS BIT(1) +#define FSPI_MCR0_SWRST BIT(0) + +#define FSPI_MCR1 0x04 +#define FSPI_MCR1_SEQ_TIMEOUT (x) ((x) << 16) +#define FSPI_MCR1_AHB_TIMEOUT (x) (x) + +#define FSPI_MCR2 0x08 +#define FSPI_MCR2_IDLE_WAIT (x) ((x) << 24) +#define FSPI_MCR2_SAMEDEVICEEN BIT(15) +#define FSPI_MCR2_CLRLRPHS BIT(14) +#define FSPI_MCR2_ABRDATSZ BIT(8) +#define FSPI_MCR2_ABRLEARN BIT(7) +#define FSPI_MCR2_ABR_READ BIT(6) +#define FSPI_MCR2_ABRWRITE BIT(5) +#define FSPI_MCR2_ABRDUMMY BIT(4) +#define FSPI_MCR2_ABR_MODE BIT(3) +#define FSPI_MCR2_ABRCADDR BIT(2) +#define FSPI_MCR2_ABRRADDR BIT(1) +#define FSPI_MCR2_ABR_CMD BIT(0) + +#define FSPI_AHBCR 0x0c +#define FSPI_AHBCR_RDADDROPT BIT(6) +#define FSPI_AHBCR_PREF_EN BIT(5) +#define FSPI_AHBCR_BUFF_EN BIT(4) +#define FSPI_AHBCR_CACH_EN BIT(3) +#define FSPI_AHBCR_CLRTXBUF BIT(2) +#define FSPI_AHBCR_CLRRXBUF BIT(1) +#define FSPI_AHBCR_PAR_EN BIT(0) + +#define FSPI_INTEN 0x10 +#define FSPI_INTEN_SCLKSBWR BIT(9) +#define FSPI_INTEN_SCLKSBRD BIT(8) +#define FSPI_INTEN_DATALRNFL BIT(7) +#define FSPI_INTEN_IPTXWE BIT(6) +#define FSPI_INTEN_IPRXWA BIT(5) +#define FSPI_INTEN_AHBCMDERR BIT(4) +#define FSPI_INTEN_IPCMDERR BIT(3) +#define FSPI_INTEN_AHBCMDGE BIT(2) +#define FSPI_INTEN_IPCMDGE BIT(1) +#define FSPI_INTEN_IPCMDDONE BIT(0) + +#define FSPI_INTR 0x14 +#define FSPI_INTR_SCLKSBWR BIT(9) +#define FSPI_INTR_SCLKSBRD BIT(8) +#define FSPI_INTR_DATALRNFL BIT(7) +#define FSPI_INTR_IPTXWE BIT(6) +#define FSPI_INTR_IPRXWA BIT(5) +#define FSPI_INTR_AHBCMDERR BIT(4) +#define FSPI_INTR_IPCMDERR BIT(3) +#define FSPI_INTR_AHBCMDGE BIT(2) +#define FSPI_INTR_IPCMDGE BIT(1) +#define FSPI_INTR_IPCMDDONE BIT(0) + +#define FSPI_LUTKEY 0x18 +#define FSPI_LUTKEY_VALUE 0x5AF05AF0 + +#define FSPI_LCKCR 0x1C + +#define FSPI_LCKER_LOCK 0x1 +#define FSPI_LCKER_UNLOCK 0x2 + +#define FSPI_BUFXCR_INVALID_MSTRID 0xE +#define FSPI_AHBRX_BUF0CR0 0x20 +#define FSPI_AHBRX_BUF1CR0 0x24 +#define FSPI_AHBRX_BUF2CR0 0x28 +#define FSPI_AHBRX_BUF3CR0 0x2C +#define FSPI_AHBRX_BUF4CR0 0x30 +#define FSPI_AHBRX_BUF5CR0 0x34 +#define FSPI_AHBRX_BUF6CR0 0x38 +#define FSPI_AHBRX_BUF7CR0 0x3C +#define FSPI_AHBRXBUF0CR7_PREF BIT(31) + +#define FSPI_AHBRX_BUF0CR1 0x40 +#define FSPI_AHBRX_BUF1CR1 0x44 +#define FSPI_AHBRX_BUF2CR1 0x48 +#define FSPI_AHBRX_BUF3CR1 0x4C +#define FSPI_AHBRX_BUF4CR1 0x50 +#define FSPI_AHBRX_BUF5CR1 0x54 +#define FSPI_AHBRX_BUF6CR1 0x58 +#define FSPI_AHBRX_BUF7CR1 0x5C + +#define FSPI_FLSHA1CR0 0x60 +#define FSPI_FLSHA2CR0 0x64 +#define FSPI_FLSHB1CR0 0x68 +#define FSPI_FLSHB2CR0 0x6C +#define FSPI_FLSHXCR0_SZ_KB 10 +#define FSPI_FLSHXCR0_SZ (x) ((x) >> FSPI_FLSHXCR0_SZ_KB) + +#define FSPI_FLSHA1CR1 0x70 +#define FSPI_FLSHA2CR1 0x74 +#define FSPI_FLSHB1CR1 0x78 +#define FSPI_FLSHB2CR1 0x7C +#define FSPI_FLSHXCR1_CSINTR (x) ((x) << 16) +#define FSPI_FLSHXCR1_CAS (x) ((x) << 11) +#define FSPI_FLSHXCR1_WA BIT(10) +#define FSPI_FLSHXCR1_TCSH (x) ((x) << 5) +#define FSPI_FLSHXCR1_TCSS (x) (x) + +#define FSPI_FLSHA1CR2 0x80 +#define FSPI_FLSHA2CR2 0x84 +#define FSPI_FLSHB1CR2 0x88 +#define FSPI_FLSHB2CR2 0x8C +#define FSPI_FLSHXCR2_CLRINSP BIT(24) +#define FSPI_FLSHXCR2_AWRWAIT BIT(16) +#define FSPI_FLSHXCR2_AWRSEQN_SHIFT 13 +#define FSPI_FLSHXCR2_AWRSEQI_SHIFT 8 +#define FSPI_FLSHXCR2_ARDSEQN_SHIFT 5 +#define FSPI_FLSHXCR2_ARDSEQI_SHIFT 0 + +#define FSPI_IPCR0 0xA0 + +#define FSPI_IPCR1 0xA4 +#define FSPI_IPCR1_IPAREN BIT(31) +#define FSPI_IPCR1_SEQNUM_SHIFT 24 +#define FSPI_IPCR1_SEQID_SHIFT 16 +#define FSPI_IPCR1_IDATSZ (x) (x) + +#define FSPI_IPCMD 0xB0 +#define FSPI_IPCMD_TRG BIT(0) + +#define FSPI_DLPR 0xB4 + +#define FSPI_IPRXFCR 0xB8 +#define FSPI_IPRXFCR_CLR BIT(0) +#define FSPI_IPRXFCR_DMA_EN BIT(1) +#define FSPI_IPRXFCR_WMRK (x) ((x) << 2) + +#define FSPI_IPTXFCR 0xBC +#define FSPI_IPTXFCR_CLR BIT(0) +#define FSPI_IPTXFCR_DMA_EN BIT(1) +#define FSPI_IPTXFCR_WMRK (x) ((x) << 2) + +#define FSPI_DLLACR 0xC0 +#define FSPI_DLLACR_OVRDEN BIT(8) + +#define FSPI_DLLBCR 0xC4 +#define FSPI_DLLBCR_OVRDEN BIT(8) + +#define FSPI_STS0 0xE0 +#define FSPI_STS0_DLPHB (x) ((x) << 8) +#define FSPI_STS0_DLPHA (x) ((x) << 4) +#define FSPI_STS0_CMD_SRC (x) ((x) << 2) +#define FSPI_STS0_ARB_IDLE BIT(1) +#define FSPI_STS0_SEQ_IDLE BIT(0) + +#define FSPI_STS1 0xE4 +#define FSPI_STS1_IP_ERRCD (x) ((x) << 24) +#define FSPI_STS1_IP_ERRID (x) ((x) << 16) +#define FSPI_STS1_AHB_ERRCD (x) ((x) << 8) +#define FSPI_STS1_AHB_ERRID (x) (x) + +#define FSPI_AHBSPNST 0xEC +#define FSPI_AHBSPNST_DATLFT (x) ((x) << 16) +#define FSPI_AHBSPNST_BUFID (x) ((x) << 1) +#define FSPI_AHBSPNST_ACTIVE BIT(0) + +#define FSPI_IPRXFSTS 0xF0 +#define FSPI_IPRXFSTS_RDCNTR (x) ((x) << 16) +#define FSPI_IPRXFSTS_FILL (x) (x) + +#define FSPI_IPTXFSTS 0xF4 +#define FSPI_IPTXFSTS_WRCNTR (x) ((x) << 16) +#define FSPI_IPTXFSTS_FILL (x) (x) + +#define FSPI_RFDR 0x100 +#define FSPI_TFDR 0x180 + +#define FSPI_LUT_BASE 0x200 +#define FSPI_LUT_OFFSET (SEQID_LUT * 4 * 4) +#define FSPI_LUT_REG (idx) \ + (FSPI_LUT_BASE + FSPI_LUT_OFFSET + (idx) * 4) + +/* register map end */ + +/* Instruction set for the LUT register. */ +#define LUT_STOP 0x00 +#define LUT_CMD 0x01 +#define LUT_ADDR 0x02 +#define LUT_CADDR_SDR 0x03 +#define LUT_MODE 0x04 +#define LUT_MODE2 0x05 +#define LUT_MODE4 0x06 +#define LUT_MODE8 0x07 +#define LUT_NXP_WRITE 0x08 +#define LUT_NXP_READ 0x09 +#define LUT_LEARN_SDR 0x0A +#define LUT_DATSZ_SDR 0x0B +#define LUT_DUMMY 0x0C +#define LUT_DUMMY_RWDS_SDR 0x0D +#define LUT_JMP_ON_CS 0x1F +#define LUT_CMD_DDR 0x21 +#define LUT_ADDR_DDR 0x22 +#define LUT_CADDR_DDR 0x23 +#define LUT_MODE_DDR 0x24 +#define LUT_MODE2_DDR 0x25 +#define LUT_MODE4_DDR 0x26 +#define LUT_MODE8_DDR 0x27 +#define LUT_WRITE_DDR 0x28 +#define LUT_READ_DDR 0x29 +#define LUT_LEARN_DDR 0x2A +#define LUT_DATSZ_DDR 0x2B +#define LUT_DUMMY_DDR 0x2C +#define LUT_DUMMY_RWDS_DDR 0x2D + +/* +* Calculate number of required PAD bits for LUT register. +* +* The pad stands for the number of IO lines [0:7]. +* For example, the octal read needs eight IO lines, +* so you should use LUT_PAD(8). This macro +* returns 3 i.e. use eight (2^3) IP lines for read. +*/ +#define LUT_PAD (x) (fls(x) - 1) + +/* +* Macro for constructing the LUT entries with the following +* register layout: +* +* --------------------------------------------------- +* | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 | +* --------------------------------------------------- +*/ +#define PAD_SHIFT 8 +#define INSTR_SHIFT 10 +#define OPRND_SHIFT 16 + +/* Macros for constructing the LUT register. */ +#define LUT_DEF (idx, ins, pad, opr) \ + ((((ins) << INSTR_SHIFT) | ((pad) << PAD_SHIFT) | \ + (opr)) << (((idx) % 2) * OPRND_SHIFT)) + +#define POLL_TOUT 5000 +#define NXP_FSPI_MAX_CHIPSELECT 4 + +struct nxp_fspi_devtype_data { +unsigned int rxfifo; +unsigned int txfifo; +unsigned int ahb_buf_size; +unsigned int quirks; +bool little_endian; +}; + +static const struct nxp_fspi_devtype_data lx2160a_data = { + .rxfifo =SZ_512 ,/* (64 * 64 bits) */ + .txfifo =SZ_1K ,/* (128 * 64 bits) */ + .ahb_buf_size =SZ_2K ,/* (256 * 64 bits) */ + .quirks =0 , + .little_endian = true,/* little-endian */ +}; + +struct nxp_fspi { +void __iomem *iobase; +void __iomem *ahb_addr; +u32 memmap_phy; +u32 memmap_phy_size; +struct clk *clk, *clk_en; +struct device *dev; +struct completion c; +const struct nxp_fspi_devtype_data *devtype_data; +struct mutex lock; +struct pm_qos_request pm_qos_req; +int selected; +}; + +/* +* R/W functions for big- or little-endian registers: +* The FSPI controller's endianness is independent of +* the CPU core's endianness. So far, although the CPU +* core is little-endian the FSPI controller can use +* big-endian or little-endian. +*/ +static void fspi_writel (struct nxp_fspi *f,u32 val,void __iomem +*addr) { +if (f->devtype_data->little_endian) +iowrite32 (val, addr); +else +iowrite32be (val, addr); +} + +static u32 fspi_readl (struct nxp_fspi *f,void __iomem *addr) { +if (f->devtype_data->little_endian) +return ioread32 (addr); +else +return ioread32be (addr); +} + +static irqreturn_t nxp_fspi_irq_handler (int irq,void *dev_id) { +struct nxp_fspi *f = dev_id; +u32 reg; + +/* clear interrupt */ + reg =fspi_readl (f, f->iobase +FSPI_INTR ); +fspi_writel (f,FSPI_INTR_IPCMDDONE , f->iobase +FSPI_INTR ); + +if (reg &FSPI_INTR_IPCMDDONE ) +complete (&f->c); + +return IRQ_HANDLED ; +} + +static int nxp_fspi_check_buswidth (struct nxp_fspi *f,u8 width) { +switch (width) { +case 1 : +case 2 : +case 4 : +case 8 : +return 0 ; + } + +return -ENOTSUPP ; +} + +static bool nxp_fspi_supports_op (struct spi_mem *mem, +const struct spi_mem_op *op) +{ +struct nxp_fspi *f =spi_controller_get_devdata (mem->spi->master); +int ret; + + ret =nxp_fspi_check_buswidth (f, op->cmd.buswidth); + +if (op->addr.nbytes) + ret |=nxp_fspi_check_buswidth (f, op->addr.buswidth); + +if (op->dummy.nbytes) + ret |=nxp_fspi_check_buswidth (f, op->dummy.buswidth); + +if (op->data.nbytes) + ret |=nxp_fspi_check_buswidth (f, op->data.buswidth); + +if (ret) +return false; + +/* +* The number of address bytes should be equal to or less than 4 bytes. +*/ +if (op->addr.nbytes >4 ) +return false; + +/* +* If requested address value is greater than controller assigned +* memory mapped space, return error as it didn't fit in the range +* of assigned address space. +*/ +if (op->addr.val >= f->memmap_phy_size) +return false; + +/* Max 64 dummy clock cycles supported */ +if (op->dummy.buswidth && + (op->dummy.nbytes *8 / op->dummy.buswidth >64 )) +return false; + +/* Max data length, check controller limits and alignment */ +if (op->data.dir ==SPI_MEM_DATA_IN && + (op->data.nbytes > f->devtype_data->ahb_buf_size || + (op->data.nbytes > f->devtype_data->rxfifo -4 && + !IS_ALIGNED (op->data.nbytes,8 )))) +return false; + +if (op->data.dir ==SPI_MEM_DATA_OUT && + op->data.nbytes > f->devtype_data->txfifo) +return false; + +return true; +} + +/* Instead of busy looping invoke readl_poll_timeout functionality. */ +static int fspi_readl_poll_tout (struct nxp_fspi *f,void __iomem *base, +u32 mask,u32 delay_us, +u32 timeout_us,bool c) +{ +u32 reg; + +if (!f->devtype_data->little_endian) + mask = (u32 )cpu_to_be32 (mask); + +if (c) +return readl_poll_timeout (base, reg, (reg & mask), + delay_us, timeout_us); +else +return readl_poll_timeout (base, reg, !(reg & mask), + delay_us, timeout_us); +} + +/* +* If the slave device content being changed by Write/Erase, need to +* invalidate the AHB buffer. This can be achieved by doing the reset +* of controller after setting MCR0[SWRESET] bit. +*/ +static inline void nxp_fspi_invalid (struct nxp_fspi *f) { +u32 reg; +int ret; + + reg =fspi_readl (f, f->iobase +FSPI_MCR0 ); +fspi_writel (f, reg |FSPI_MCR0_SWRST , f->iobase +FSPI_MCR0 ); + +/* w1c register, wait unit clear */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_MCR0 , +FSPI_MCR0_SWRST ,0 ,POLL_TOUT , false); +WARN_ON (ret); +} + +static void nxp_fspi_prepare_lut (struct nxp_fspi *f, +const struct spi_mem_op *op) +{ +void __iomem *base = f->iobase; +u32 lutval[4 ] = {}; +int lutidx =1 , i; + +/* cmd */ + lutval[0 ] |=LUT_DEF (0 ,LUT_CMD ,LUT_PAD (op->cmd.buswidth), + op->cmd.opcode); + +/* addr bytes */ +if (op->addr.nbytes) { + lutval[lutidx /2 ] |=LUT_DEF (lutidx,LUT_ADDR , +LUT_PAD (op->addr.buswidth), + op->addr.nbytes *8 ); + lutidx++; + } + +/* dummy bytes, if needed */ +if (op->dummy.nbytes) { + lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_DUMMY, +/* +* Due to FlexSPI controller limitation number of PAD for dummy
drivers/spi/spi-nxp-fspi.c new file +12
-0+* buswidth needs to be programmed as equal to data buswidth. +*/ +LUT_PAD (op->data.buswidth), + op->dummy.nbytes *8 / + op->dummy.buswidth); + lutidx++; + } + +/* read/write data bytes */ +if (op->data.nbytes) { + lutval[lutidx / 2] |= LUT_DEF(lutidx, + op->data.dir ==
SPI_MEM_DATA_IN?drivers/spi/spi-nxp-fspi.c new file +359
-0+ LUT_NXP_READ :LUT_NXP_WRITE , +LUT_PAD (op->data.buswidth), + 0); + lutidx++; + } + +/* stop condition. */ + lutval[lutidx /2 ] |=LUT_DEF (lutidx,LUT_STOP ,0 ,0 ); + +/* unlock LUT */ +fspi_writel (f,FSPI_LUTKEY_VALUE , f->iobase +FSPI_LUTKEY ); +fspi_writel (f,FSPI_LCKER_UNLOCK , f->iobase +FSPI_LCKCR ); + +/* fill LUT */ +for (i =0 ; i <ARRAY_SIZE (lutval); i++) +fspi_writel (f, lutval[i], base +FSPI_LUT_REG (i)); + +dev_dbg (f->dev,"CMD[%x] lutval[0:%x \t 1:%x \t 2:%x \t 3:%x]\n" , + op->cmd.opcode, lutval[0 ], lutval[1 ], lutval[2 ], lutval[3 ]); + +/* lock LUT */ +fspi_writel (f,FSPI_LUTKEY_VALUE , f->iobase +FSPI_LUTKEY ); +fspi_writel (f,FSPI_LCKER_LOCK , f->iobase +FSPI_LCKCR ); } + +static int nxp_fspi_clk_prep_enable (struct nxp_fspi *f) { +int ret; + + ret =clk_prepare_enable (f->clk_en); +if (ret) +return ret; + + ret =clk_prepare_enable (f->clk); +if (ret) { +clk_disable_unprepare (f->clk_en); +return ret; + } + +return 0 ; +} + +static void nxp_fspi_clk_disable_unprep (struct nxp_fspi *f) { +clk_disable_unprepare (f->clk); +clk_disable_unprepare (f->clk_en); +} + +/* +* In FlexSPI controller, flash access is based on value of +FSPI_FLSHXXCR0 +* register and start base address of the slave device. +* +* (Higher address) +* -------- <-- FLSHB2CR0 +* | B2 | +* | | +* B2 start address --> -------- <-- FLSHB1CR0 +* | B1 | +* | | +* B1 start address --> -------- <-- FLSHA2CR0 +* | A2 | +* | | +* A2 start address --> -------- <-- FLSHA1CR0 +* | A1 | +* | | +* A1 start address --> -------- (Lower address) +* +* +* Start base address defines the starting address range for given CS +and +* FSPI_FLSHXXCR0 defines the size of the slave device connected at given CS. +* +* But, different targets are having different combinations of number +of CS, +* some targets only have single CS or two CS covering controller's +full +* memory mapped space area. +* Thus, implementation is being done as independent of the size and +number +* of the connected slave device. +* Assign controller memory mapped space size as the size to the +connected +* slave device. +* Mark FLSHxxCR0 as zero initially and then assign value only to the +selected +* chip-select Flash configuration register. +* +* For e.g. to access CS2 (B1), FLSHB1CR0 register would be equal to +the +* memory mapped size of the controller. +* Value for rest of the CS FLSHxxCR0 register would be zero. +* +*/ +static void nxp_fspi_select_mem (struct nxp_fspi *f,struct spi_device +*spi) { +unsigned long rate = spi->max_speed_hz; +int ret; +uint64_t size_kb; + +/* +* Return, if previously selected slave device is same as current +* requested slave device. +*/ +if (f->selected == spi->chip_select) +return ; + +/* Reset FLSHxxCR0 registers */ +fspi_writel (f,0 , f->iobase +FSPI_FLSHA1CR0 ); +fspi_writel (f,0 , f->iobase +FSPI_FLSHA2CR0 ); +fspi_writel (f,0 , f->iobase +FSPI_FLSHB1CR0 ); +fspi_writel (f,0 , f->iobase +FSPI_FLSHB2CR0 ); + +/* Assign controller memory mapped space as size, KBytes, of flash. */ + size_kb =FSPI_FLSHXCR0_SZ (f->memmap_phy_size); + +fspi_writel (f, size_kb, f->iobase +FSPI_FLSHA1CR0 + +4 * spi->chip_select); + +dev_dbg (f->dev,"Slave device [CS:%x] selected\n" , spi->chip_select); + +nxp_fspi_clk_disable_unprep (f); + + ret =clk_set_rate (f->clk, rate); +if (ret) +return ; + + ret =nxp_fspi_clk_prep_enable (f); +if (ret) +return ; + + f->selected = spi->chip_select; +} + +static void nxp_fspi_read_ahb (struct nxp_fspi *f,const struct +spi_mem_op *op) { +u32 len = op->data.nbytes; + +/* Read out the data directly from the AHB buffer. */ +memcpy_fromio (op->data.buf.in, (f->ahb_addr + op->addr.val), len); } + +static void nxp_fspi_fill_txfifo (struct nxp_fspi *f, +const struct spi_mem_op *op) +{ +void __iomem *base = f->iobase; +int i, ret; +u8 *buf = (u8 *) op->data.buf.out; + +/* clear the TX FIFO. */ +fspi_writel (f,FSPI_IPTXFCR_CLR , base +FSPI_IPTXFCR ); + +/* +* Default value of water mark level is 8 bytes, hence in single +* write request controller can write max 8 bytes of data. +*/ + +for (i =0 ; i <ALIGN_DOWN (op->data.nbytes,8 ); i +=8 ) { +/* Wait for TXFIFO empty */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_INTR , +FSPI_INTR_IPTXWE ,0 , +POLL_TOUT , true); +WARN_ON (ret); + +fspi_writel (f, *(u32 *) (buf + i), base +FSPI_TFDR ); +fspi_writel (f, *(u32 *) (buf + i +4 ), base +FSPI_TFDR +4 ); +fspi_writel (f,FSPI_INTR_IPTXWE , base +FSPI_INTR ); + } + +if (i < op->data.nbytes) { +u32 data =0 ; +int j; +/* Wait for TXFIFO empty */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_INTR , +FSPI_INTR_IPTXWE ,0 , +POLL_TOUT , true); +WARN_ON (ret); + +for (j =0 ; j <ALIGN (op->data.nbytes - i,4 ); j +=4 ) { +memcpy (&data, buf + i + j,4 ); +fspi_writel (f, data, base +FSPI_TFDR + j); + } +fspi_writel (f,FSPI_INTR_IPTXWE , base +FSPI_INTR ); + } +} + +static void nxp_fspi_read_rxfifo (struct nxp_fspi *f, +const struct spi_mem_op *op) +{ +void __iomem *base = f->iobase; +int i, ret; +int len = op->data.nbytes; +u8 *buf = (u8 *) op->data.buf.in; + +/* +* Default value of water mark level is 8 bytes, hence in single +* read request controller can read max 8 bytes of data. +*/ +for (i =0 ; i <ALIGN_DOWN (len,8 ); i +=8 ) { +/* Wait for RXFIFO available */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_INTR , +FSPI_INTR_IPRXWA ,0 , +POLL_TOUT , true); +WARN_ON (ret); + + *(u32 *)(buf + i) =fspi_readl (f, base +FSPI_RFDR ); + *(u32 *)(buf + i +4 ) =fspi_readl (f, base +FSPI_RFDR +4 ); +/* move the FIFO pointer */ +fspi_writel (f,FSPI_INTR_IPRXWA , base +FSPI_INTR ); + } + +if (i < len) { +u32 tmp; +int size, j; + + buf = op->data.buf.in + i; +/* Wait for RXFIFO available */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_INTR , +FSPI_INTR_IPRXWA ,0 , +POLL_TOUT , true); +WARN_ON (ret); + + len = op->data.nbytes - i; +for (j =0 ; j < op->data.nbytes - i; j +=4 ) { + tmp =fspi_readl (f, base +FSPI_RFDR + j); + size =min (len,4 ); +memcpy (buf + j, &tmp, size); + len -= size; + } + } + +/* invalid the RXFIFO */ +fspi_writel (f,FSPI_IPRXFCR_CLR , base +FSPI_IPRXFCR ); +/* move the FIFO pointer */ +fspi_writel (f,FSPI_INTR_IPRXWA , base +FSPI_INTR ); } + +static int nxp_fspi_do_op (struct nxp_fspi *f,const struct spi_mem_op +*op) { +void __iomem *base = f->iobase; +int seqnum =0 ; +int err =0 ; +u32 reg; + + reg =fspi_readl (f, base +FSPI_IPRXFCR ); +/* invalid RXFIFO first */ + reg &= ~FSPI_IPRXFCR_DMA_EN ; + reg = reg |FSPI_IPRXFCR_CLR ; +fspi_writel (f, reg, base +FSPI_IPRXFCR ); + +init_completion (&f->c); + +fspi_writel (f, op->addr.val, base +FSPI_IPCR0 ); +/* +* Always start the sequence at the same index since we update +* the LUT at each exec_op() call. And also specify the DATA +* length, since it's has not been specified in the LUT. +*/ +fspi_writel (f, op->data.nbytes | + (SEQID_LUT <<FSPI_IPCR1_SEQID_SHIFT ) | + (seqnum <<FSPI_IPCR1_SEQNUM_SHIFT ), + base +FSPI_IPCR1 ); + +/* Trigger the LUT now. */ +fspi_writel (f,FSPI_IPCMD_TRG , base +FSPI_IPCMD ); + +/* Wait for the interrupt. */ +if (!wait_for_completion_timeout (&f->c,msecs_to_jiffies (1000 ))) + err = -ETIMEDOUT ; + +/* Invoke IP data read, if request is of data read. */ +if (!err && op->data.nbytes && op->data.dir ==SPI_MEM_DATA_IN ) +nxp_fspi_read_rxfifo (f, op); + +return err; +} + +static int nxp_fspi_exec_op (struct spi_mem *mem,const struct +spi_mem_op *op) { +struct nxp_fspi *f =spi_controller_get_devdata (mem->spi->master); +int err =0 ; + +mutex_lock (&f->lock); + +/* Wait for controller being ready. */ + err =fspi_readl_poll_tout (f, f->iobase +FSPI_STS0 , +FSPI_STS0_ARB_IDLE ,1 ,POLL_TOUT , true); +WARN_ON (err); + +nxp_fspi_select_mem (f, mem->spi); + +nxp_fspi_prepare_lut (f, op); +/* +* If we have large chunks of data, we read them through the AHB bus +* by accessing the mapped memory. In all other cases we use +* IP commands to access the flash. +*/ +if (op->data.nbytes > (f->devtype_data->rxfifo -4 ) && + op->data.dir ==SPI_MEM_DATA_IN ) { +nxp_fspi_read_ahb (f, op); + }else { +if (op->data.nbytes && op->data.dir ==SPI_MEM_DATA_OUT ) +nxp_fspi_fill_txfifo (f, op); + + err =nxp_fspi_do_op (f, op); + } + +/* Invalidate the data in the AHB buffer. */ +nxp_fspi_invalid (f); + +mutex_unlock (&f->lock); + +return err; +} + +static int nxp_fspi_adjust_op_size (struct spi_mem *mem,struct +spi_mem_op *op) { +struct nxp_fspi *f =spi_controller_get_devdata (mem->spi->master); + +if (op->data.dir ==SPI_MEM_DATA_OUT ) { +if (op->data.nbytes > f->devtype_data->txfifo) + op->data.nbytes = f->devtype_data->txfifo; + }else { +if (op->data.nbytes > f->devtype_data->ahb_buf_size) + op->data.nbytes = f->devtype_data->ahb_buf_size; +else if (op->data.nbytes > (f->devtype_data->rxfifo -4 )) + op->data.nbytes =ALIGN_DOWN (op->data.nbytes,8 ); + } + +return 0 ; +} + +static int nxp_fspi_default_setup (struct nxp_fspi *f) { +void __iomem *base = f->iobase; +int ret, i; +u32 reg; + +/* disable and unprepare clock to avoid glitch pass to controller */ +nxp_fspi_clk_disable_unprep (f); + +/* the default frequency, we will change it later if necessary. */ + ret =clk_set_rate (f->clk,20000000 ); +if (ret) +return ret; + + ret =nxp_fspi_clk_prep_enable (f); +if (ret) +return ret; + +/* Reset the module */ +/* w1c register, wait unit clear */ + ret =fspi_readl_poll_tout (f, f->iobase +FSPI_MCR0 , +FSPI_MCR0_SWRST ,0 ,POLL_TOUT , false); +WARN_ON (ret); + +/* Disable the module */ +fspi_writel (f,FSPI_MCR0_MDIS , base +FSPI_MCR0 ); + +/* Reset the DLL register to default value */ +fspi_writel (f,FSPI_DLLACR_OVRDEN , base +FSPI_DLLACR ); +fspi_writel (f,FSPI_DLLBCR_OVRDEN , base +FSPI_DLLBCR ); + +/* enable module */ + fspi_writel(f, FSPI_MCR0_AHB_TIMEOUT(0xFF) |
FSPI_MCR0_IP_TIMEOUT(0xFF),drivers/spi/spi-nxp-fspi.c new file +94
-0+ base + FSPI_MCR0); + +/* +* Disable same device enable bit and configure all slave devices +* independently. +*/ + reg =fspi_readl (f, f->iobase +FSPI_MCR2 ); + reg = reg & ~(FSPI_MCR2_SAMEDEVICEEN ); +fspi_writel (f, reg, base +FSPI_MCR2 ); + +/* AHB configuration for access buffer 0~7. */ +for (i =0 ; i <7 ; i++) +fspi_writel (f,0 , base +FSPI_AHBRX_BUF0CR0 +4 * i); + +/* +* Set ADATSZ with the maximum AHB buffer size to improve the read +* performance. +*/ +fspi_writel (f, (f->devtype_data->ahb_buf_size /8 | +FSPI_AHBRXBUF0CR7_PREF ), base +FSPI_AHBRX_BUF7CR0 ); + +/* prefetch and no start address alignment limitation */ +fspi_writel (f,FSPI_AHBCR_PREF_EN |FSPI_AHBCR_RDADDROPT , + base +FSPI_AHBCR ); + +/* AHB Read - Set lut sequence ID for all CS. */ +fspi_writel (f,SEQID_LUT , base +FSPI_FLSHA1CR2 ); +fspi_writel (f,SEQID_LUT , base +FSPI_FLSHA2CR2 ); +fspi_writel (f,SEQID_LUT , base +FSPI_FLSHB1CR2 ); +fspi_writel (f,SEQID_LUT , base +FSPI_FLSHB2CR2 ); + + f->selected =-1 ; + +/* enable the interrupt */ +fspi_writel (f,FSPI_INTEN_IPCMDDONE , base +FSPI_INTEN ); + +return 0 ; +} + +static const char *nxp_fspi_get_name (struct spi_mem *mem) { +struct nxp_fspi *f =spi_controller_get_devdata (mem->spi->master); +struct device *dev = &mem->spi->dev; +const char *name; + +// Set custom name derived from the platform_device of the controller. +if (of_get_available_child_count (f->dev->of_node) ==1 ) +return dev_name (f->dev); + + name =devm_kasprintf (dev,GFP_KERNEL , +"%s-%d" ,dev_name (f->dev), + mem->spi->chip_select); + +if (!name) { +dev_err (dev,"failed to get memory for custom flash name\n" ); +return ERR_PTR (-ENOMEM ); + } + +return name; +} + +static const struct spi_controller_mem_ops nxp_fspi_mem_ops = { + .adjust_op_size = nxp_fspi_adjust_op_size, + .supports_op = nxp_fspi_supports_op, + .exec_op = nxp_fspi_exec_op, + .get_name = nxp_fspi_get_name, +}; + +static int nxp_fspi_probe (struct platform_device *pdev) { +struct spi_controller *ctlr; +struct device *dev = &pdev->dev; +struct device_node *np = dev->of_node; +struct resource *res; +struct nxp_fspi *f; +int ret; + + ctlr =spi_alloc_master (&pdev->dev,sizeof (*f)); +if (!ctlr) +return -ENOMEM ; + + ctlr->mode_bits =SPI_RX_DUAL |SPI_RX_QUAD | +SPI_TX_DUAL |SPI_TX_QUAD ; + + f =spi_controller_get_devdata (ctlr); + f->dev = dev; + f->devtype_data =of_device_get_match_data (dev); +if (!f->devtype_data) { + ret = -ENODEV ; + goto err_put_ctrl; + } + +platform_set_drvdata (pdev, f); + +/* find the resources - configuration register address space */ + res = platform_get_resource_byname(pdev, IORESOURCE_MEM,"
fspi_base");drivers/spi/spi-nxp-fspi.c new file +8
-0+ f->iobase =devm_ioremap_resource (dev, res); +if (IS_ERR (f->iobase)) { + ret =PTR_ERR (f->iobase); + goto err_put_ctrl; + } + +/* find the resources - controller memory mapped space */ + res = platform_get_resource_byname(pdev, IORESOURCE_MEM,"
fspi_mmap");drivers/spi/spi-nxp-fspi.c new file +120
-0+ f->ahb_addr =devm_ioremap_resource (dev, res); +if (IS_ERR (f->ahb_addr)) { + ret =PTR_ERR (f->ahb_addr); + goto err_put_ctrl; + } + +/* assign memory mapped starting address and mapped size. */ + f->memmap_phy = res->start; + f->memmap_phy_size =resource_size (res); + +/* find the clocks */ + f->clk_en =devm_clk_get (dev,"fspi_en" ); +if (IS_ERR (f->clk_en)) { + ret =PTR_ERR (f->clk_en); + goto err_put_ctrl; + } + + f->clk =devm_clk_get (dev,"fspi" ); +if (IS_ERR (f->clk)) { + ret =PTR_ERR (f->clk); + goto err_put_ctrl; + } + + ret =nxp_fspi_clk_prep_enable (f); +if (ret) { +dev_err (dev,"can not enable the clock\n" ); + goto err_put_ctrl; + } + +/* find the irq */ + ret =platform_get_irq (pdev,0 ); +if (ret <0 ) { +dev_err (dev,"failed to get the irq: %d\n" , ret); + goto err_disable_clk; + } + + ret =devm_request_irq (dev, ret, + nxp_fspi_irq_handler,0 , pdev->name, f); +if (ret) { +dev_err (dev,"failed to request irq: %d\n" , ret); + goto err_disable_clk; + } + +mutex_init (&f->lock); + + ctlr->bus_num =-1 ; + ctlr->num_chipselect =NXP_FSPI_MAX_CHIPSELECT ; + ctlr->mem_ops = &nxp_fspi_mem_ops; + +nxp_fspi_default_setup (f); + + ctlr->dev.of_node = np; + + ret =spi_register_controller (ctlr); +if (ret) + goto err_destroy_mutex; + +return 0 ; + +err_destroy_mutex: +mutex_destroy (&f->lock); + +err_disable_clk: +nxp_fspi_clk_disable_unprep (f); + +err_put_ctrl: +spi_controller_put (ctlr); + +dev_err (dev,"NXP FSPI probe failed\n" ); +return ret; +} + +static int nxp_fspi_remove (struct platform_device *pdev) { +struct nxp_fspi *f =platform_get_drvdata (pdev); + +/* disable the hardware */ +fspi_writel (f,FSPI_MCR0_MDIS , f->iobase +FSPI_MCR0 ); + +nxp_fspi_clk_disable_unprep (f); + +mutex_destroy (&f->lock); + +return 0 ; +} + +static int nxp_fspi_suspend (struct device *dev) { +return 0 ; +} + +static int nxp_fspi_resume (struct device *dev) { +struct nxp_fspi *f =dev_get_drvdata (dev); + +nxp_fspi_default_setup (f); + +return 0 ; +} + +static const struct of_device_id nxp_fspi_dt_ids[] = { + { .compatible ="nxp,lx2160a-fspi" , .data = (void *)&lx2160a_data, }, + {/* sentinel */ } +}; +MODULE_DEVICE_TABLE (of, nxp_fspi_dt_ids); + +static const struct dev_pm_ops nxp_fspi_pm_ops = { + .suspend = nxp_fspi_suspend, + .resume = nxp_fspi_resume, +}; + +static struct platform_driver nxp_fspi_driver = { + .driver = { + .name ="nxp-fspi" , + .of_match_table = nxp_fspi_dt_ids, + .pm = &nxp_fspi_pm_ops, + }, + .probe = nxp_fspi_probe, + .remove = nxp_fspi_remove, +}; +module_platform_driver (nxp_fspi_driver); + +MODULE_DESCRIPTION ("NXP FSPI Controller Driver" );MODULE_AUTHOR("NXP
+Semiconductor");MODULE_AUTHOR("Yogesh Narayan Gaur +<[email protected]>");MODULE_AUTHOR("Boris Brezillion +<[email protected]>");MODULE_AUTHOR("Frieder Schrempf +<[email protected]>");MODULE_LICENSE("GPL v2"); --
2.17.1______________________________________________________
Linux MTD discussion mailing list
https://emea01.safelinks.protection.outlook.com/?url=http%3A%2F%2Flists.infr
adead.org%2Fmailman%2Flistinfo%2Flinux- mtd%2F&data=02%7C01%7Cashish.kumar%40nxp.com%7Cf61d5430fbb8 46cc953e08d67ae1238f%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0 %7C636831504726799549&sdata=%2FUKvN5oeGCfp8kbre6XEhxl3dk78p pP5m0jzltcfAE4%3D&reserved=0
Mark Brown
maintainerApplied "spi: spi-mem: Add driver for NXP FlexSPI controller" to the spi tree
In reply to Yogesh Narayan GaurThe patch
spi: spi-mem: Add driver for NXP FlexSPI controller
has been applied to the spi tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
Quoted 1 line
From
a5356aef6a907c2e2aed0caaa2b88b6021394471Mon Sep 17 00:00:00 2001
From: Yogesh Narayan Gaur <[email protected]>
Date: Tue, 15 Jan 2019 12:00:15 +0000
Subject: [PATCH] spi: spi-mem: Add driver for NXP FlexSPI controller
- Add driver for NXP FlexSPI host controller
(0) What is the FlexSPI controller?
FlexSPI is a flexsible SPI host controller which supports two SPI channels and up to 4 external devices. Each channel supports Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional data lines) i.e. FlexSPI acts as an interface to external devices, maximum 4, each with up to 8 bidirectional data lines.
It uses new SPI memory interface of the SPI framework to issue flash memory operations to up to four connected flash devices (2 buses with 2 CS each).
(1) Tested this driver with the mtd_debug and JFFS2 filesystem utility on NXP LX2160ARDB and LX2160AQDS targets.
LX2160ARDB is having two NOR slave device connected on single bus A i.e. A0 and A1 (CS0 and CS1).
LX2160AQDS is having two NOR slave device connected on separate buses one flash on A0 and second on B1 i.e. (CS0 and CS3). Verified this driver on following SPI NOR flashes:
Micron, mt35xu512ab, [Read - 1 bit mode]
Cypress, s25fl512s, [Read - 1/2/4 bit mode]--- drivers/spi/Kconfig | 10 + drivers/spi/Makefile | 1 + drivers/spi/spi-nxp-fspi.c | 1105 ++++++++++++++++++++++++++++++++++++ 3 files changed, 1116 insertions(+) create mode 100644 drivers/spi/spi-nxp-fspi.c
drivers/spi/Kconfig +10 -0
@@ -279,6 +279,16 @@ config SPI_FSL_QUADSPI This controller does not support generic SPI messages. It only supports the high-level SPI memory interface. +config SPI_NXP_FLEXSPI + tristate "NXP Flex SPI controller" + depends on ARCH_LAYERSCAPE || HAS_IOMEM + help + This enables support for the Flex SPI controller in master mode. + Up to four slave devices can be connected on two buses with two + chipselects each. + This controller does not support generic SPI messages and only + supports the high-level SPI memory interface. + config SPI_GPIO tristate "GPIO-based bitbanging SPI Master" depends on GPIOLIB || COMPILE_TEST
drivers/spi/Makefile +1 -0
@@ -64,6 +64,7 @@ obj-$(CONFIG_SPI_MXIC) += spi-mxic.o obj-$(CONFIG_SPI_MXS) += spi-mxs.o obj-$(CONFIG_SPI_NPCM_PSPI) += spi-npcm-pspi.o obj-$(CONFIG_SPI_NUC900) += spi-nuc900.o +obj-$(CONFIG_SPI_NXP_FLEXSPI) += spi-nxp-fspi.o obj-$(CONFIG_SPI_OC_TINY) += spi-oc-tiny.o spi-octeon-objs := spi-cavium.o spi-cavium-octeon.o obj-$(CONFIG_SPI_OCTEON) += spi-octeon.o
drivers/spi/spi-nxp-fspi.c new file +1105 -0
1,105 lines not on this page · raw message
Signature · 1 line
2.20.1
PATCH v8 2/5 dt-bindings: spi: add binding file for NXP FlexSPI controller
In reply to Yogesh Narayan GaurAdd binding file for NXP FlexSPI controller
---
Changes for v8:
- None
Changes for v7:
- None
Changes for v6:
- None
Changes for v5:
- None
Changes for v4:
- Incorporated Rob review comments.
Changes for v3:
- Removed node property 'big-endian'.
Changes for v2:
- Incorporated Rob review comments.
.../devicetree/bindings/spi/spi-nxp-fspi.txt | 39 +++++++++++++++++++ 1 file changed, 39 insertions(+) create mode 100644 Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt
Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt new file +39 -0
@@ -0,0 +1,39 @@ +* NXP Flex Serial Peripheral Interface (FSPI) + +Required properties: + - compatible : Should be "nxp,lx2160a-fspi" + - reg : First contains the register location and length, + Second contains the memory mapping address and length + - reg-names : Should contain the resource reg names: + - fspi_base: configuration register address space + - fspi_mmap: memory mapped address space + - interrupts : Should contain the interrupt for the device + +Required SPI slave node properties: + - reg : There are two buses (A and B) with two chip selects each. + This encodes to which bus and CS the flash is connected: + - <0>: Bus A, CS 0 + - <1>: Bus A, CS 1 + - <2>: Bus B, CS 0 + - <3>: Bus B, CS 1 + +Example showing the usage of two SPI NOR slave devices on bus A: + +fspi0: spi@20c0000 { + compatible = "nxp,lx2160a-fspi"; + reg = <0x0 0x20c0000 0x0 0x10000>, <0x0 0x20000000 0x0 0x10000000>; + reg-names = "fspi_base", "fspi_mmap"; + interrupts = <0 25 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "fspi_en", "fspi"; + + mt35xu512aba0: flash@0 { + reg = <0>; + .... + }; + + mt35xu512aba1: flash@1 { + reg = <1>; + .... + }; +};
Signature · 1 line
2.17.1
RE: [PATCH v8 2/5] dt-bindings: spi: add binding file for NXP FlexSPI controller
Hi Rob / Shawn,
Can you please apply patches [1] [2].
--
Regards,
Yogesh Gaur
[1] https://patchwork.ozlabs.org/patch/1025136/
[2] https://patchwork.ozlabs.org/patch/1025137/
Quoted 86 lines
-----Original Message-----
From: Yogesh Narayan Gaur
Sent: Tuesday, January 15, 2019 5:30 PM
To: [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]
Cc: [email protected]; [email protected]; [email protected]; linux- [email protected]; [email protected]; [email protected]; [email protected]; Yogesh Narayan Gaur <[email protected]>
Subject: [PATCH v8 2/5] dt-bindings: spi: add binding file for NXP FlexSPI controllerAdd binding file for NXP FlexSPI controller
Signed-off-by Yogesh Narayan Gaur <[email protected]>Reviewed-by Rob Herring <[email protected]>---
Changes for v8:
- None
Changes for v7:
- None
Changes for v6:
- None
Changes for v5:
- None
Changes for v4:
- Incorporated Rob review comments.
Changes for v3:
- Removed node property 'big-endian'.
Changes for v2:
- Incorporated Rob review comments..../devicetree/bindings/spi/spi-nxp-fspi.txt | 39 +++++++++++++++++++ 1 file changed, 39 insertions(+) create mode 100644 Documentation/devicetree/bindings/spi/spi-nxp-fspi.txtDocumentation/devicetree/bindings/spi/spi-nxp-fspi.txt new file +24
-0@@ -0,0 +1,39 @@ +* NXP Flex Serial Peripheral Interface (FSPI) + +Required properties: + - compatible : Should be "nxp,lx2160a-fspi" + - reg : First contains the register location and length, + Second contains the memory mapping address and length + - reg-names : Should contain the resource reg names: + - fspi_base: configuration register address space + - fspi_mmap: memory mapped address space + - interrupts : Should contain the interrupt for the device + +Required SPI slave node properties: + - reg : There are two buses (A and B) with two chip selects each. + This encodes to which bus and CS the flash is connected: + - <0>: Bus A, CS 0 + - <1>: Bus A, CS 1 + - <2>: Bus B, CS 0 + - <3>: Bus B, CS 1 + +Example showing the usage of two SPI NOR slave devices on bus A: + +fspi0: spi@20c0000 { + compatible = "nxp,lx2160a-fspi"; + reg = <0x0 0x20c0000 0x0 0x10000>, <0x0 0x20000000 0x0
0x10000000>;Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt new file +15
-1+ reg-names = "fspi_base", "fspi_mmap"; + interrupts = <0 25 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "fspi_en", "fspi"; + + mt35xu512aba0: flash@0 { + reg = <0>; + .... + }; + + mt35xu512aba1: flash@1 { + reg = <1>; + .... + }; +}; --2.17.1
Re: [PATCH v8 2/5] dt-bindings: spi: add binding file for NXP FlexSPI controller
Quoted 3 lines · On Tue, 22 Jan 2019 09:00:14 +0000 Yogesh Narayan Gaur…
Hi Rob / Shawn,
Can you please apply patches [1] [2].
No, DT bindings should go through Mark's tree. Just wait a bit please.
RE: [PATCH v8 2/5] dt-bindings: spi: add binding file for NXP FlexSPI controller
Hi Boris,
Quoted 12 lines
-----Original Message-----
From: Boris Brezillon [mailto:[email protected]]
Sent: Tuesday, January 22, 2019 2:47 PM
To: Yogesh Narayan Gaur <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]
Subject: Re: [PATCH v8 2/5] dt-bindings: spi: add binding file for NXP FlexSPI controller
Quoted 8 lines
Quoted 3 lines · On Tue, 22 Jan 2019 09:00:14 +0000 Yogesh Narayan Gaur…
Hi Rob / Shawn,
Can you please apply patches [1] [2].
No, DT bindings should go through Mark's tree. Just wait a bit please.
Ok, thanks.
--
Regards
Yogesh Gaur
PATCH v8 3/5 arm64: dts: lx2160a: add FlexSPI node property
In reply to Yogesh Narayan GaurAdd fspi node property for LX2160A SoC for FlexSPI driver. Property added for the FlexSPI controller and for the connected slave device for the LX2160ARDB target.
This is having two SPI-NOR flash device, mt35xu512aba, connected at CS0 and CS1.
---
Changes for v8:
- None
Changes for v7:
- None
Changes for v6:
- None
Changes for v5:
- None
Changes for v4:
- Incorporated Rob review comments.
Changes for v3:
- None.
Changes for v2:
- Incorporated Shawn review comments.
.../boot/dts/freescale/fsl-lx2160a-rdb.dts | 22 +++++++++++++++++++ .../arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 13 +++++++++++ 2 files changed, 35 insertions(+)
arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts +22 -0
@@ -50,6 +50,28 @@ status = "okay"; }; +&fspi { + status = "okay"; + + mt35xu512aba0: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + m25p,fast-read; + spi-max-frequency = <50000000>; + reg = <0>; + }; + + mt35xu512aba1: flash@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + m25p,fast-read; + spi-max-frequency = <50000000>; + reg = <1>; + }; +}; + &i2c0 { status = "okay";
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +13 -0
@@ -762,5 +762,18 @@ <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; dma-coherent; }; + + fspi: spi@20c0000 { + compatible = "nxp,lx2160a-fspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x20c0000 0x0 0x10000>, + <0x0 0x20000000 0x0 0x10000000>; + reg-names = "fspi_base", "fspi_mmap"; + interrupts = <0 25 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "fspi_en", "fspi"; + status = "disabled"; + }; }; };
Signature · 1 line
2.17.1
Re: [PATCH v8 3/5] arm64: dts: lx2160a: add FlexSPI node property
Quoted 65 lines · Yogesh Narayan Gaur
Add fspi node property for LX2160A SoC for FlexSPI driver. Property added for the FlexSPI controller and for the connected slave device for the LX2160ARDB target.
This is having two SPI-NOR flash device, mt35xu512aba, connected at CS0 and CS1.Signed-off-by Yogesh Narayan Gaur <[email protected]>---
Changes for v8:
- None
Changes for v7:
- None
Changes for v6:
- None
Changes for v5:
- None
Changes for v4:
- Incorporated Rob review comments.
Changes for v3:
- None.
Changes for v2:
- Incorporated Shawn review comments..../boot/dts/freescale/fsl-lx2160a-rdb.dts | 22 +++++++++++++++++++ .../arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 13 +++++++++++ 2 files changed, 35 insertions(+)arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts +22
-0@@ -50,6 +50,28 @@ status = "okay"; }; +&fspi { + status = "okay"; + + mt35xu512aba0: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + m25p,fast-read; + spi-max-frequency = <50000000>; + reg = <0>; + }; + + mt35xu512aba1: flash@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + m25p,fast-read; + spi-max-frequency = <50000000>; + reg = <1>; + }; +}; + &i2c0 { status = "okay";arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +0
-0
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi line 766
Quoted 5 lines
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +2
-0@@ -762,5 +762,18 @@ <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; dma-coherent; }; + + fspi: spi@20c0000 {
To keep the nodes sorted in unit-address, it should go after i2c@2070000.
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi line 771
Quoted 5 lines
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +5
-0+ compatible = "nxp,lx2160a-fspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x20c0000 0x0 0x10000>, + <0x0 0x20000000 0x0 0x10000000>;
I would align the indentation with the above.
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi line 773
Quoted 2 lines
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +2
-0+ reg-names = "fspi_base", "fspi_mmap"; + interrupts = <0 25 0x4>; /* Level high type */
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; so that we can save the comment there.
I fixed up all these small things and applied the patch.
Shawn
Quoted 14 lines
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +4
-0+ clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "fspi_en", "fspi"; + status = "disabled"; + }; }; };Signature · 7 lines
2.17.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
RE: [PATCH v8 3/5] arm64: dts: lx2160a: add FlexSPI node property
Quoted 97 lines
-----Original Message-----
From: Shawn Guo [mailto:[email protected]]
Sent: Friday, February 1, 2019 8:24 AM
To: Yogesh Narayan Gaur <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; linux- [email protected]; [email protected]; [email protected]; [email protected]
Subject: Re: [PATCH v8 3/5] arm64: dts: lx2160a: add FlexSPI node propertyQuoted 67 lines · Yogesh Narayan Gaur
Add fspi node property for LX2160A SoC for FlexSPI driver. Property added for the FlexSPI controller and for the connected slave device for the LX2160ARDB target.
This is having two SPI-NOR flash device, mt35xu512aba, connected at CS0 and CS1.Signed-off-by Yogesh Narayan Gaur <[email protected]>---
Changes for v8:
- None
Changes for v7:
- None
Changes for v6:
- None
Changes for v5:
- None
Changes for v4:
- Incorporated Rob review comments.
Changes for v3:
- None.
Changes for v2:
- Incorporated Shawn review comments..../boot/dts/freescale/fsl-lx2160a-rdb.dts | 22 +++++++++++++++++++ .../arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 13 +++++++++++ 2 files changed, 35 insertions(+)arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts +22
-0@@ -50,6 +50,28 @@ status = "okay"; }; +&fspi { + status = "okay"; + + mt35xu512aba0: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + m25p,fast-read; + spi-max-frequency = <50000000>; + reg = <0>; + }; + + mt35xu512aba1: flash@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + m25p,fast-read; + spi-max-frequency = <50000000>; + reg = <1>; + }; +}; + &i2c0 { status = "okay";arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +0
-0arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi line 766
Quoted 5 lines
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +2
-0@@ -762,5 +762,18 @@ <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; dma-coherent; }; + + fspi: spi@20c0000 {To keep the nodes sorted in unit-address, it should go after i2c@2070000.
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi line 771
Quoted 5 lines
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +5
-0+ compatible = "nxp,lx2160a-fspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x20c0000 0x0 0x10000>, + <0x0 0x20000000 0x0 0x10000000>;I would align the indentation with the above.
Quoted 8 lines
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi line 773
Quoted 2 lines
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +2
-0+ reg-names = "fspi_base", "fspi_mmap"; + interrupts = <0 25 0x4>; /* Level high type */interrupts = <
GIC_SPI25IRQ_TYPE_LEVEL_HIGH>; so that we can save the comment there.I fixed up all these small things and applied the patch.
Ok, Thanks.
--
Regards
Yogesh Gaur.
Quoted 27 lines
Shawn
Quoted 10 lines
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +4
-1+ clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "fspi_en", "fspi"; + status = "disabled"; + }; }; }; --2.17.1
Quoted 5 lines
_______________________________________________
linux-arm-kernel mailing list
[email protected]
https://emea01.safelinks.protection.outlook.com/?url=http%3A%2F%2Flist
s.infradead.org%2Fmailman%2Flistinfo%2Flinux-arm-kernel&data=02%7C
Quoted 1 line
01%7Cyogeshnarayan.gaur%40nxp.com%7C6308464db1a541247dfd08d687f09 124%7
Quoted 1 line
C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C636845864632818753&a mp;sda
Quoted 1 line
ta=urGFUKDP6ZZZOTXS1ccfLceCV2OBV5%2BiZq9foCu7ZX8%3D&reserved= 0
PATCH v8 4/5 arm64: defconfig: enable NXP FlexSPI driver
In reply to Yogesh Narayan GaurEnable driver support of NXP FlexSPI controller.
---
Changes for v8:
- None
Changes for v7:
- None
Changes for v6:
- None
Changes for v5:
- None
Changes for v4:
- None
Changes for v3:
- None
Changes for v2:
- None
arch/arm64/configs/defconfig | 1 + 1 file changed, 1 insertion(+)
arch/arm64/configs/defconfig +1 -0
@@ -362,6 +362,7 @@ CONFIG_SPI_ROCKCHIP=y CONFIG_SPI_QUP=y CONFIG_SPI_S3C64XX=y CONFIG_SPI_SPIDEV=m +CONFIG_SPI_NXP_FLEXSPI=y CONFIG_SPMI=y CONFIG_PINCTRL_SINGLE=y CONFIG_PINCTRL_MAX77620=y
Signature · 1 line
2.17.1
Shawn Guo
AppliedRe: [PATCH v8 4/5] arm64: defconfig: enable NXP FlexSPI driver
Quoted 3 lines · Yogesh Narayan Gaur
Enable driver support of NXP FlexSPI controller.
Signed-off-by Yogesh Narayan Gaur <[email protected]>
Applied, thanks.
PATCH v8 5/5 MAINTAINERS: add maintainers for the NXP FlexSPI driver
In reply to Yogesh Narayan GaurAdd maintainers for the NXP FlexSPI driver
---
Changes for v8:
- Update entry for NXP FlexSPI maintainers name
Changes for v7:
- None
Changes for v6:
- None
Changes for v5:
- Add maintainers for binding file
Changes for v4:
- None
Changes for v3:
- None
Changes for v2:
- None
MAINTAINERS | 8 ++++++++ 1 file changed, 8 insertions(+)
MAINTAINERS +8 -0
@@ -10927,6 +10927,14 @@ F: lib/objagg.c F: lib/test_objagg.c F: include/linux/objagg.h +NXP FSPI DRIVER +R: Yogesh Gaur <[email protected]> +M: Ashish Kumar <[email protected]> +L: [email protected] +S: Maintained +F: drivers/spi/spi-nxp-fspi.c +F: Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt + OBJTOOL M: Josh Poimboeuf <[email protected]> M: Peter Zijlstra <[email protected]>
Signature · 1 line
2.17.1
Mark Brown
maintainerApplied "MAINTAINERS: add maintainers for the NXP FlexSPI driver" to the spi tree
The patch
MAINTAINERS: add maintainers for the NXP FlexSPI driver
has been applied to the spi tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
Quoted 1 line
From
c71f9fd4503addcfa306f9bec95c3e7deade7ce1Mon Sep 17 00:00:00 2001
From: Yogesh Narayan Gaur <[email protected]>
Date: Tue, 15 Jan 2019 12:00:37 +0000
Subject: [PATCH] MAINTAINERS: add maintainers for the NXP FlexSPI driver
Add maintainers for the NXP FlexSPI driver
--- MAINTAINERS | 8 ++++++++ 1 file changed, 8 insertions(+)
MAINTAINERS +8 -0
@@ -10927,6 +10927,14 @@ F: lib/objagg.c F: lib/test_objagg.c F: include/linux/objagg.h +NXP FSPI DRIVER +R: Yogesh Gaur <[email protected]> +M: Ashish Kumar <[email protected]> +L: [email protected] +S: Maintained +F: drivers/spi/spi-nxp-fspi.c +F: Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt + OBJTOOL M: Josh Poimboeuf <[email protected]> M: Peter Zijlstra <[email protected]>
Signature · 1 line
2.20.1