Skip to contentSkip to conversation

gpio: zynq: properly support runtime PM for GPIO used as interrupts

PATCH In review Thomas Petazzoni 3 participants 3 messages Feb 8, 2019 – Feb 13, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 gpio: zynq: properly support runtime PM for GPIO used as interrupts

The Zynq GPIO driver currently implements runtime PM by:

- Enabling runtime PM support in ->probe() and letting the runtime PM reference counter drop to zero at the end of ->probe().

- Increasing the runtime PM reference counter in ->request() and decreasing it in ->free().

However, the latter is not sufficient: when a GPIO is used as an interrupt, ->request() and ->free() are not called. Due to this, the runtime PM counter remains to zero when the only GPIOs in use are used as interrupts, causing them to simply not work.

To address this problem, this commit implement the ->irq_request_resources() and ->irq_release_resources() hooks, ensuring that the runtime PM counter is properly incremented/decremented. Since we override the default hooks, we keep the existing behavior by making sure they call gpiochip_reqres_irq() / gpiochip_relres_irq() respectively.

---
 drivers/gpio/gpio-zynq.c | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)
drivers/gpio/gpio-zynq.c +24 -0
index 3f5fcdd5a429..65c0c29ce851 100644
@@ -533,6 +533,26 @@ static int zynq_gpio_set_wake(struct irq_data *data, unsigned int on)
 	return 0;
 }
 
+static int zynq_gpio_irq_reqres(struct irq_data *d)
+{
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(d);
+	int ret;
+
+	ret = pm_runtime_get_sync(chip->parent);
+	if (ret < 0)
+		return ret;
+
+	return gpiochip_reqres_irq(chip, d->hwirq);
+}
+
+static void zynq_gpio_irq_relres(struct irq_data *d)
+{
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(d);
+
+	gpiochip_relres_irq(chip, d->hwirq);
+	pm_runtime_put(chip->parent);
+}
+
 /* irq chip descriptor */
 static struct irq_chip zynq_gpio_level_irqchip = {
 	.name		= DRIVER_NAME,
@@ -542,6 +562,8 @@ static struct irq_chip zynq_gpio_level_irqchip = {
 	.irq_unmask	= zynq_gpio_irq_unmask,
 	.irq_set_type	= zynq_gpio_set_irq_type,
 	.irq_set_wake	= zynq_gpio_set_wake,
+	.irq_request_resources = zynq_gpio_irq_reqres,
+	.irq_release_resources = zynq_gpio_irq_relres,
 	.flags		= IRQCHIP_EOI_THREADED | IRQCHIP_EOI_IF_HANDLED |
 			  IRQCHIP_MASK_ON_SUSPEND,
 };
@@ -554,6 +576,8 @@ static struct irq_chip zynq_gpio_edge_irqchip = {
 	.irq_unmask	= zynq_gpio_irq_unmask,
 	.irq_set_type	= zynq_gpio_set_irq_type,
 	.irq_set_wake	= zynq_gpio_set_wake,
+	.irq_request_resources = zynq_gpio_irq_reqres,
+	.irq_release_resources = zynq_gpio_irq_relres,
 	.flags		= IRQCHIP_MASK_ON_SUSPEND,
 };
 
Signature · 1 line
2.20.1
Reviewed-by on v1 1/1
#1 lore raw

Hi Thomas,

Thanks for the patch.

Quoted 21 lines · Thomas Petazzoni

The Zynq GPIO driver currently implements runtime PM by:

- Enabling runtime PM support in ->probe() and letting the runtime PM reference counter drop to zero at the end of ->probe().

- Increasing the runtime PM reference counter in ->request() and decreasing it in ->free().

However, the latter is not sufficient: when a GPIO is used as an interrupt, ->request() and ->free() are not called. Due to this, the runtime PM counter remains to zero when the only GPIOs in use are used as interrupts, causing them to simply not work.

To address this problem, this commit implement the ->irq_request_resources() and ->irq_release_resources() hooks, ensuring that the runtime PM counter is properly incremented/decremented. Since we override the default hooks, we keep the existing behavior by making sure they call gpiochip_reqres_irq() / gpiochip_relres_irq() respectively.

Quoted 2 lines

---

Quoted 1 line
#2 lore raw
In reply to Thomas Petazzoni
Quoted 13 lines · Thomas Petazzoni

The Zynq GPIO driver currently implements runtime PM by:

- Enabling runtime PM support in ->probe() and letting the runtime PM reference counter drop to zero at the end of ->probe().

- Increasing the runtime PM reference counter in ->request() and decreasing it in ->free().

However, the latter is not sufficient: when a GPIO is used as an interrupt, ->request() and ->free() are not called. Due to this, the runtime PM counter remains to zero when the only GPIOs in use are used as interrupts, causing them to simply not work.

Quoted 8 lines

To address this problem, this commit implement the ->irq_request_resources() and ->irq_release_resources() hooks, ensuring that the runtime PM counter is properly incremented/decremented. Since we override the default hooks, we keep the existing behavior by making sure they call gpiochip_reqres_irq() / gpiochip_relres_irq() respectively.

Patch applied with Shubhrajyoti's review tag.

Yours,
Linus Walleij