lx2160aqds : Add support for LX2160AQDS platform
PATCH v6 1/1 lx2160aqds : Add support for LX2160AQDS platform
LX2160AQDS is a development board that supports LX2160A family SoCs. This patch add base support for this board.
---
Notes:
This patch depends on following patches:
http://patchwork.ozlabs.org/patch/1030280/
V6
- Rebased on latest LX2160ARDB distro boot support patch
- Added 2019 in copyright
- Fixed some formatting errors.
V5
- Add "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" in phy nodes for PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45 specifications.
V4
- changed the LX2160ARDB to LX2160AQDS in dts file description Also removed the Author info from dts file header
dts file : arch/arm/dts/fsl-lx2160a-qds.dts
V3
- modified the fdt phy fixup function as per fdt.
refer https://patchwork.codeaurora.org/patch/657515/
V2:
- removed checkpatch warnings about line over 80 chars
- Added CONFIG_FSL_MC_ENET macro in eth_lx2160aqds.c file
to avoid compilation errors if this macro is not defined
V1:
The checkpatch script reported 28 warnings about line over 80 characters, that i have not corrected. as IMO doing so, makes the code less legible.
arch/arm/Kconfig | 13 + arch/arm/cpu/armv8/Kconfig | 1 + arch/arm/dts/Makefile | 3 +- arch/arm/dts/fsl-lx2160a-qds.dts | 17 + .../asm/arch-fsl-layerscape/immap_lsch3.h | 10 +- board/freescale/lx2160a/Kconfig | 18 + board/freescale/lx2160a/MAINTAINERS | 9 + board/freescale/lx2160a/Makefile | 1 + board/freescale/lx2160a/README | 118 +++ board/freescale/lx2160a/eth_lx2160aqds.c | 805 +++++++++++++++++ board/freescale/lx2160a/lx2160a.c | 279 +++++- configs/lx2160aqds_tfa_defconfig | 72 ++ include/configs/lx2160aqds.h | 140 +++ 13 files changed, 1483 insertions(+), 3 deletions(-)
arch/arm/Kconfig +13 -0
@@ -1090,6 +1090,19 @@ config TARGET_LX2160ARDB is a high-performance development platform that supports the QorIQ LX2160A/LX2120A/LX2080A Layerscape Architecture processor. +config TARGET_LX2160AQDS + bool "Support lx2160aqds" + select ARCH_LX2160A + select ARCH_MISC_INIT + select ARM64 + select ARMV8_MULTIENTRY + select BOARD_LATE_INIT + help + Support for NXP LX2160AQDS platform. + The lx2160aqds (LX2160A QorIQ Development System (QDS) + is a high-performance development platform that supports the + QorIQ LX2160A/LX2120A/LX2080A Layerscape Architecture processor. + config TARGET_HIKEY bool "Support HiKey 96boards Consumer Edition Platform" select ARM64
arch/arm/cpu/armv8/Kconfig +1 -0
@@ -107,6 +107,7 @@ config PSCI_RESET !TARGET_LS1043ARDB && !TARGET_LS1043AQDS && \ !TARGET_LS1046ARDB && !TARGET_LS1046AQDS && \ !TARGET_LS2081ARDB && !TARGET_LX2160ARDB && \ + !TARGET_LX2160AQDS && \ !ARCH_UNIPHIER && !TARGET_S32V234EVB help Most armv8 systems have PSCI support enabled in EL3, either through
arch/arm/dts/Makefile +2 -1
@@ -242,7 +242,8 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \ fsl-ls2088a-rdb-qspi.dtb \ fsl-ls1088a-rdb.dtb \ fsl-ls1088a-qds.dtb \ - fsl-lx2160a-rdb.dtb + fsl-lx2160a-rdb.dtb \ + fsl-lx2160a-qds.dtb dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \ fsl-ls1043a-qds-lpuart.dtb \ fsl-ls1043a-rdb.dtb \
arch/arm/dts/fsl-lx2160a-qds.dts new file +17 -0
@@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2160AQDS device tree source + * + * Copyright 2018-2019 NXP + * + */ + +/dts-v1/; + +#include "fsl-lx2160a.dtsi" + +/ { + model = "NXP Layerscape LX2160AQDS Board"; + compatible = "fsl,lx2160aqds", "fsl,lx2160a"; +}; +
arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h +9 -1
@@ -2,7 +2,7 @@/* * LayerScape Internal Memory Map * -* Copyright 2017-2018 NXP +* Copyright 2017-2019 NXP * Copyright 2014 Freescale Semiconductor, Inc. */
@@ -350,6 +350,14 @@ struct ccsr_gur {#define FSL_CHASSIS3_SRDS1_REGSR 29#define FSL_CHASSIS3_SRDS2_REGSR 29#define FSL_CHASSIS3_SRDS3_REGSR 29 +#define FSL_CHASSIS3_RCWSR12_REGSR 12 +#define FSL_CHASSIS3_RCWSR13_REGSR 13 +#define FSL_CHASSIS3_SDHC1_BASE_PMUX_MASK 0x07000000 +#define FSL_CHASSIS3_SDHC1_BASE_PMUX_SHIFT 24 +#define FSL_CHASSIS3_SDHC2_BASE_PMUX_MASK 0x00000038 +#define FSL_CHASSIS3_SDHC2_BASE_PMUX_SHIFT 3 +#define FSL_CHASSIS3_IIC5_PMUX_MASK 0x00000E00 +#define FSL_CHASSIS3_IIC5_PMUX_SHIFT 9#elif defined(CONFIG_ARCH_LS1088A )#define FSL_CHASSIS3_EC1_REGSR 26#define FSL_CHASSIS3_EC2_REGSR 26
board/freescale/lx2160a/Kconfig +18 -0
@@ -14,3 +14,21 @@ config SYS_CONFIG_NAME source "board/freescale/common/Kconfig" endif + +if TARGET_LX2160AQDS + +config SYS_BOARD + default "lx2160a" + +config SYS_VENDOR + default "freescale" + +config SYS_SOC + default "fsl-layerscape" + +config SYS_CONFIG_NAME + default "lx2160aqds" + +source "board/freescale/common/Kconfig" +endif +
board/freescale/lx2160a/MAINTAINERS +9 -0
@@ -6,3 +6,12 @@ F: include/configs/lx2160a_common.h F: include/configs/lx2160ardb.h F: configs/lx2160ardb_defconfig F: arch/arm/dts/fsl-lx2160a-rdb.dts + +LX2160AQDS BOARD +M: Pankaj Bansal <[email protected]> +S: Maintained +F: board/freescale/lx2160a/eth_lx2160aqds.h +F: include/configs/lx2160aqds.h +F: configs/lx2160aqds_tfa_defconfig +F: arch/arm/dts/fsl-lx2160a-qds.dts +
board/freescale/lx2160a/Makefile +1 -0
@@ -7,3 +7,4 @@ obj-y += lx2160a.o obj-y += ddr.o obj-$(CONFIG_TARGET_LX2160ARDB) += eth_lx2160ardb.o +obj-$(CONFIG_TARGET_LX2160AQDS) += eth_lx2160aqds.o
board/freescale/lx2160a/README +118 -0
121 lines not on this page · raw message
board/freescale/lx2160a/eth_lx2160aqds.c new file +805 -0
805 lines not on this page · raw message
board/freescale/lx2160a/lx2160a.c +278 -1
333 lines not on this page · raw message
configs/lx2160aqds_tfa_defconfig new file +72 -0
72 lines not on this page · raw message
include/configs/lx2160aqds.h new file +140 -0
140 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v6 1/1 lx2160aqds : Add support for LX2160AQDS platform
Quoted 10 lines
-----Original Message-----
From: Pankaj Bansal
Sent: Friday, February 8, 2019 4:00 PM
To: Meenakshi Aggarwal <[email protected]>; Prabhakar Kushwaha <[email protected]>
Cc: u-boot at lists.denx.de; Pankaj Bansal <[email protected]>; Wasim Khan <[email protected]>; Sriram Dash <[email protected]>
Subject: [PATCH v6] lx2160aqds : Add support for LX2160AQDS platform
Quoted 7 lines
LX2160AQDS is a development board that supports LX2160A family SoCs. This patch add base support for this board.
Signed-off-by Wasim Khan <[email protected]>Signed-off-by Sriram Dash <[email protected]>Signed-off-by Pankaj Bansal <[email protected]>---
This patch been applied to fsl-qoriq master, awaiting upstream.
--pk
Quoted 1,793 lines
Notes:
This patch depends on following patches:
http://patchwork.ozlabs.org/patch/1030280/
V6
- Rebased on latest LX2160ARDB distro boot support patch
- Added 2019 in copyright
- Fixed some formatting errors.
V5
- Add "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" in
phy
nodes for PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45 specifications.
V4
- changed the LX2160ARDB to LX2160AQDS in dts file description Also removed the Author info from dts file header
dts file :arch/arm/dts/fsl-lx2160a-qds.dts
V3
- modified the fdt phy fixup function as per fdt.
refer https://patchwork.codeaurora.org/patch/657515/
V2:
- removed checkpatch warnings about line over 80 chars
- AddedCONFIG_FSL_MC_ENETmacro ineth_lx2160aqds.cfile
to avoid compilation errors if this macro is not defined
V1:
The checkpatch script reported 28 warnings about line over 80 characters, that i have not corrected. as IMO doing so, makes the code less legible.arch/arm/Kconfig | 13 + arch/arm/cpu/armv8/Kconfig | 1 + arch/arm/dts/Makefile | 3 +- arch/arm/dts/fsl-lx2160a-qds.dts | 17 + .../asm/arch-fsl-layerscape/immap_lsch3.h | 10 +- board/freescale/lx2160a/Kconfig | 18 + board/freescale/lx2160a/MAINTAINERS | 9 + board/freescale/lx2160a/Makefile | 1 + board/freescale/lx2160a/README | 118 +++ board/freescale/lx2160a/eth_lx2160aqds.c | 805 +++++++++++++++++ board/freescale/lx2160a/lx2160a.c | 279 +++++- configs/lx2160aqds_tfa_defconfig | 72 ++ include/configs/lx2160aqds.h | 140 +++ 13 files changed, 1483 insertions(+), 3 deletions(-)arch/arm/Kconfig +0
-0@@ -1090,6 +1090,19 @@ config TARGET_LX2160ARDB is a high-performance development platform that supports the QorIQ LX2160A/LX2120A/LX2080A Layerscape Architectureprocessor.
arch/arm/Kconfig +12
-0+config TARGET_LX2160AQDS + bool "Support lx2160aqds" + select ARCH_LX2160A + select ARCH_MISC_INIT + select ARM64 + select ARMV8_MULTIENTRY + select BOARD_LATE_INIT + help + Support for NXP LX2160AQDS platform. + The lx2160aqds (LX2160A QorIQ Development System (QDS) + is a high-performance development platform that supports the + QorIQ LX2160A/LX2120A/LX2080A Layerscape Architectureprocessor.
arch/arm/Kconfig +1
-0+ config TARGET_HIKEY bool "Support HiKey 96boards Consumer Edition Platform" select ARM64arch/arm/cpu/armv8/Kconfig +1
-0@@ -107,6 +107,7 @@ config PSCI_RESET !TARGET_LS1043ARDB && !TARGET_LS1043AQDS && \ !TARGET_LS1046ARDB && !TARGET_LS1046AQDS && \ !TARGET_LS2081ARDB && !TARGET_LX2160ARDB && \ + !TARGET_LX2160AQDS && \ !ARCH_UNIPHIER && !TARGET_S32V234EVB help Most armv8 systems have PSCI support enabled in EL3, eitherthrough
arch/arm/dts/Makefile +2
-1@@ -242,7 +242,8 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \ fsl-ls2088a-rdb-qspi.dtb \ fsl-ls1088a-rdb.dtb \ fsl-ls1088a-qds.dtb \ - fsl-lx2160a-rdb.dtb + fsl-lx2160a-rdb.dtb \ + fsl-lx2160a-qds.dtb dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \ fsl-ls1043a-qds-lpuart.dtb \ fsl-ls1043a-rdb.dtb \arch/arm/dts/fsl-lx2160a- renamed from arch/arm/dts/fsl-lx2160a-qds.dts +0
-0
qds.dts
new file mode 100644
index 0000000000..6192156fc3arch/arm/dts/fsl-lx2160a-qds.dts new file +17
-0@@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2160AQDS device tree source + * + * Copyright 2018-2019 NXP + * + */ + +/dts-v1/; + +#include "fsl-lx2160a.dtsi" + +/ { + model = "NXP Layerscape LX2160AQDS Board"; + compatible = "fsl,lx2160aqds", "fsl,lx2160a"; +}; +arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h +9
-1@@ -2,7 +2,7 @@/* * LayerScape Internal Memory Map * -* Copyright 2017-2018 NXP +* Copyright 2017-2019 NXP * Copyright 2014 Freescale Semiconductor, Inc. */ @@ -350,6 +350,14 @@ struct ccsr_gur {#define FSL_CHASSIS3_SRDS1_REGSR 29#define FSL_CHASSIS3_SRDS2_REGSR 29#define FSL_CHASSIS3_SRDS3_REGSR 29 +#define FSL_CHASSIS3_RCWSR12_REGSR 12 +#define FSL_CHASSIS3_RCWSR13_REGSR 13 +#define FSL_CHASSIS3_SDHC1_BASE_PMUX_MASK 0x07000000 +#define FSL_CHASSIS3_SDHC1_BASE_PMUX_SHIFT 24 +#define FSL_CHASSIS3_SDHC2_BASE_PMUX_MASK 0x00000038 +#define FSL_CHASSIS3_SDHC2_BASE_PMUX_SHIFT 3 +#define FSL_CHASSIS3_IIC5_PMUX_MASK 0x00000E00 +#define FSL_CHASSIS3_IIC5_PMUX_SHIFT 9#elif defined(CONFIG_ARCH_LS1088A )#define FSL_CHASSIS3_EC1_REGSR 26#define FSL_CHASSIS3_EC2_REGSR 26board/freescale/lx2160a/Kconfig +18
-0@@ -14,3 +14,21 @@ config SYS_CONFIG_NAME source "board/freescale/common/Kconfig" endif + +if TARGET_LX2160AQDS + +config SYS_BOARD + default "lx2160a" + +config SYS_VENDOR + default "freescale" + +config SYS_SOC + default "fsl-layerscape" + +config SYS_CONFIG_NAME + default "lx2160aqds" + +source "board/freescale/common/Kconfig" +endif +board/freescale/lx2160a/MAINTAINERS +9
-0@@ -6,3 +6,12 @@ F: include/configs/lx2160a_common.h F: include/configs/lx2160ardb.h F: configs/lx2160ardb_defconfig F: arch/arm/dts/fsl-lx2160a-rdb.dts + +LX2160AQDS BOARD +M: Pankaj Bansal <[email protected]> +S: Maintained +F: board/freescale/lx2160a/eth_lx2160aqds.h +F: include/configs/lx2160aqds.h +F: configs/lx2160aqds_tfa_defconfig +F: arch/arm/dts/fsl-lx2160a-qds.dts +board/freescale/lx2160a/Makefile +1
-0@@ -7,3 +7,4 @@ obj-y += lx2160a.o obj-y += ddr.o obj-$(CONFIG_TARGET_LX2160ARDB) += eth_lx2160ardb.o +obj-$(CONFIG_TARGET_LX2160AQDS) += eth_lx2160aqds.oboard/freescale/lx2160a/README +4
-0@@ -77,3 +77,121 @@ DPAA2 MC Firmware 0x05000 DPAA2 DPL 0x06800 DPAA2 DPC 0x07000 Kernel.itb 0x08000 + +LX2160AQDS board Overview +---------------------- +Various Mezzanine cards and their connection for different SERDESprotocols is
board/freescale/lx2160a/README +56
-0+as below: + +SERDES1 |CARDS +----------------------------------------------------------------------- +1 |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J110) + |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT2 (J111) + |Connect I/O cable to IO_SLOT2(J113) +------------------------------------------------------------------------ +3 |Mezzanine:X-M11-USXGMII (29828) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J110) + |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT2 (J111) + |Connect I/O cable to IO_SLOT2(J113) +------------------------------------------------------------------------ +7 |Mezzanine:X-M11-USXGMII (29828) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J110) + |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT2 (J111) + |Connect I/O cable to IO_SLOT2(J113) +------------------------------------------------------------------------ +8 |Mezzanine:X-M12-XFI (29829) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J110) + |Mezzanine:X-M12-XFI (29829) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT2 (J111) + |Connect I/O cable to IO_SLOT2(J113) +------------------------------------------------------------------------ +13 |Mezzanine:X-M8-100G (29734) + |Connect Hydra Cable (HDR-198816-XX-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J110) + |Mezzanine:X-M8-100G (29734) + |Connect Hydra Cable (HDR-198816-XX-ECUE) to SD_SLOT2(J111) + |Connect I/O cable to IO_SLOT2(J113) +------------------------------------------------------------------------ +15 |Mezzanine:X-M8-100G (29734) + |Connect Hydra Cable (HDR-198816-XX-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J110) + |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT2 (J111) + |Connect I/O cable to IO_SLOT2(J113) +------------------------------------------------------------------------ +17 |Mezzanine:X-M13-25G (32133) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J110) + |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT2 (J111) + |Connect I/O cable to IO_SLOT2(J113) +------------------------------------------------------------------------ +19 |Mezzanine:X-M11-USXGMII (29828), X-M13-25G (32133) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT1 (J108) + |Connect M11 I/O cable to IO_SLOT1(J110), M13 I/O cable to
IO_SLOT6(J125)board/freescale/lx2160a/README +58
-0+ |Mezzanine:X-M7-40G (29738) + |Connect Straight Cable (HDR-198816-XX-ECUE) to SD_SLOT2 (J111) + |Connect I/O cable to IO_SLOT2(J113) +------------------------------------------------------------------------ +20 |Mezzanine:X-M7-40G (29738) + |Connect Straight Cable (HDR-198816-XX-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J108) + |Mezzanine:X-M7-40G (29738) + |Connect Straight Cable (HDR-198816-XX-ECUE) to SD_SLOT2 (J111) + |Connect I/O cable to IO_SLOT2(J113) +------------------------------------------------------------------------ + + +SERDES2 |CARDS +----------------------------------------------------------------------- +2 |Mezzanine:X-M6-PCIE-X8 (29737) * + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT3 (J114) + |Connect Straight Cable (HDR-198816-XX-ECUE) to SD_SLOT4 (J117) + |Connect I/O cable to IO_SLOT3(J116) +------------------------------------------------------------------------ +3 |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT3 (J114) + |Connect I/O cable to IO_SLOT3(J116) + |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT4 (J117) + |Connect I/O cable to IO_SLOT4(J119) +------------------------------------------------------------------------ +5 |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT3 (J114) + |Connect I/O cable to IO_SLOT3(J116) + |Mezzanine:X-M5-SATA (29687) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT4 (J117) + |Connect I/O cable to IO_SLOT4(J119) +------------------------------------------------------------------------ +11 |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT3 (J114) + |Connect I/O cable to IO_SLOT7(J127) + |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT4 (J117) + |Connect I/O cable to IO_SLOT8(J131) +------------------------------------------------------------------------ + + +SERDES3 |CARDS +----------------------------------------------------------------------- +2 |Mezzanine:X-M6-PCIE-X8 (29737) * + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT5 (J120) + |Connect Straight Cable (HDR-198816-XX-ECUE) to SD_SLOT6 (J123) + |Connect I/O cable to IO_SLOT5(J122) +------------------------------------------------------------------------- +3 |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT5 (J120) + |Connect I/O cable to IO_SLOT5(J122) + |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT6 (J123) + |Connect I/O cable to IO_SLOT6(J125) +------------------------------------------------------------------------- +board/freescale/lx2160a/eth_lx2160aqds.c new file +68
-0@@ -0,0 +1,805 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright 2018-2019 NXP +* +*/ + +#include <common.h> +#include <hwconfig.h> +#include <command.h> +#include <netdev.h> +#include <malloc.h> +#include <fsl_mdio.h> +#include <miiphy.h> +#include <phy.h> +#include <fm_eth.h> +#include <asm/io.h> +#include <exports.h> +#include <asm/arch/fsl_serdes.h> +#include <fsl-mc/fsl_mc.h> +#include <fsl-mc/ldpaa_wriop.h> + +#include "../common/qixis.h" + +DECLARE_GLOBAL_DATA_PTR ; + +#define EMI_NONE 0 +#define EMI1 1/* Mdio Bus 1 */ +#define EMI2 2/* Mdio Bus 2 */ + +#if defined(CONFIG_FSL_MC_ENET ) +enum io_slot { +IO_SLOT_NONE =0 , +IO_SLOT_1 , +IO_SLOT_2 , +IO_SLOT_3 , +IO_SLOT_4 , +IO_SLOT_5 , +IO_SLOT_6 , +IO_SLOT_7 , +IO_SLOT_8 , +EMI1_RGMII1 , +EMI1_RGMII2 , +IO_SLOT_MAX +}; + +struct lx2160a_qds_mdio { +enum io_slot ioslot :4 ; +u8 realbusnum :4 ; +struct mii_dev *realbus; +}; + +/* structure explaining the phy configuration on 8 lanes of a serdes*/ +struct serdes_phy_config { +u8 serdes;/* serdes protocol */ +struct phy_config { +u8 dpmacid; +/* -1 terminated array */ +int phy_address[WRIOP_MAX_PHY_NUM +1 ]; +u8 mdio_bus; +enum io_slot ioslot; + } phy_config[SRDS_MAX_LANES ]; +}; + +/* Table defining the phy configuration on 8 lanes of a serdes. +* Various assumptions have been made while defining this table. +* e.g. for serdes1 protocol 19 it is being assumed that X-M11-USXGMII +* card is being used for dpmac 3-4. (X-M12-XFI could also have been used) +* And also that this card is connected to IO Slot 1 (could have been connected
+ * to any of the 8 IO slots (IO slot 1 - IO slot 8)).
+ * similarly, it is also being assumed that MDIO 1 is selected on X-M7-40G card
+ * used in serdes1 protocol 19 (could have selected MDIO 2)
+ * To override these settings "dpmac" environment variable can be used after
+ * defining "dpmac_override" in hwconfig environment variable.
+ * This table has limited serdes protocol entries. It can be expanded as per
+ * requirement.
+ */board/freescale/lx2160a/eth_lx2160aqds.c new file +27
-0+static const struct serdes_phy_config serdes1_phy_config[] = { + {3 , {{WRIOP1_DPMAC3 , {AQ_PHY_ADDR1 ,-1 }, +EMI1 ,IO_SLOT_1 }, + {WRIOP1_DPMAC4 , {AQ_PHY_ADDR2 ,-1 }, +EMI1 ,IO_SLOT_1 }, + {WRIOP1_DPMAC5 , {AQ_PHY_ADDR3 ,-1 }, +EMI1 ,IO_SLOT_1 }, + {WRIOP1_DPMAC6 , {AQ_PHY_ADDR4 ,-1 }, +EMI1 ,IO_SLOT_1 } } }, + {7 , {{WRIOP1_DPMAC3 , {AQ_PHY_ADDR1 ,-1 }, +EMI1 ,IO_SLOT_1 }, + {WRIOP1_DPMAC4 , {AQ_PHY_ADDR2 ,-1 }, +EMI1 ,IO_SLOT_1 }, + {WRIOP1_DPMAC5 , {AQ_PHY_ADDR3 ,-1 }, +EMI1 ,IO_SLOT_1 }, + {WRIOP1_DPMAC6 , {AQ_PHY_ADDR4 ,-1 }, +EMI1 ,IO_SLOT_1 }, + {WRIOP1_DPMAC7 , {SGMII_CARD_PORT1_PHY_ADDR ,-1 }, +EMI1 ,IO_SLOT_2 }, + {WRIOP1_DPMAC8 , {SGMII_CARD_PORT2_PHY_ADDR ,-1 }, +EMI1 ,IO_SLOT_2 }, + {WRIOP1_DPMAC9 , {SGMII_CARD_PORT3_PHY_ADDR ,-1 }, +EMI1 ,IO_SLOT_2 }, + {WRIOP1_DPMAC10 , {SGMII_CARD_PORT4_PHY_ADDR ,-1 }, +EMI1 ,IO_SLOT_2 } } }, + {8 , {} }, + {13, {{WRIOP1_DPMAC1, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1},
board/freescale/lx2160a/eth_lx2160aqds.c new file +4
-0+ EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC2, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_2} } }, + {15, {{WRIOP1_DPMAC1, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1},
board/freescale/lx2160a/eth_lx2160aqds.c new file +4
-0+ EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC2, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1} } }, + {17, {{WRIOP1_DPMAC3, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1},
board/freescale/lx2160a/eth_lx2160aqds.c new file +49
-0+ EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC4, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC5, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC6, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1} } }, + {19, {{WRIOP1_DPMAC2, {CORTINA_PHY_ADDR1, -1}, + EMI1, IO_SLOT_2}, + {WRIOP1_DPMAC3, {AQ_PHY_ADDR1, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC4, {AQ_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC5, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_6}, + {WRIOP1_DPMAC6, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_6} } }, + {20, {{WRIOP1_DPMAC1, {CORTINA_PHY_ADDR1, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC2, {CORTINA_PHY_ADDR1, -1}, + EMI1, IO_SLOT_2} } } +}; + +static const struct serdes_phy_config serdes2_phy_config[] = { + {2 , {} }, + {3 , {} }, + {5 , {} }, + {11 , {{WRIOP1_DPMAC12 , {SGMII_CARD_PORT2_PHY_ADDR ,-1 }, +EMI1 ,IO_SLOT_7 }, + {WRIOP1_DPMAC17 , {SGMII_CARD_PORT3_PHY_ADDR ,-1 }, +EMI1 ,IO_SLOT_7 }, + {WRIOP1_DPMAC18 , {SGMII_CARD_PORT4_PHY_ADDR ,-1 }, +EMI1 ,IO_SLOT_7 }, + {WRIOP1_DPMAC16 , {SGMII_CARD_PORT2_PHY_ADDR ,-1 }, +EMI1 ,IO_SLOT_8 }, + {WRIOP1_DPMAC13 , {SGMII_CARD_PORT3_PHY_ADDR ,-1 }, +EMI1 ,IO_SLOT_8 }, + {WRIOP1_DPMAC14 , {SGMII_CARD_PORT4_PHY_ADDR ,-1 }, +EMI1 ,IO_SLOT_8 } } }, +}; + +static const struct serdes_phy_config serdes3_phy_config[] = { + {2 , {} }, + {3 , {} } +}; + +static inline +const struct phy_config *get_phy_config (u8 serdes, + const struct serdes_phy_config*table,
board/freescale/lx2160a/eth_lx2160aqds.c new file +39
-0+ u8 table_size) +{ +int i; + +for (i =0 ; i < table_size; i++) { +if (table[i].serdes == serdes) +return table[i].phy_config; + } + +return NULL ; +} + +/* BRDCFG4 controls EMI routing for the board. +* Bits Function +* 7-6 EMI Interface #1 Primary Routing (CFG_MUX1_EMI1) (1.8V): +* EMI1 00= On-board PHY #1 +* 01= On-board PHY #2 +* 10= (reserved) +* 11= Slots 1..8 multiplexer and translator. +* 5-3 EMI Interface #1 Secondary Routing (CFG_MUX2_EMI1) (2.5V): +* EMI1X 000= Slot #1 +* 001= Slot #2 +* 010= Slot #3 +* 011= Slot #4 +* 100= Slot #5 +* 101= Slot #6 +* 110= Slot #7 +* 111= Slot #8 +* 2-0 EMI Interface #2 Routing (CFG_MUX_EMI2): +* EMI2 000= Slot #1 (secondary EMI) +* 001= Slot #2 (secondary EMI) +* 010= Slot #3 (secondary EMI) +* 011= Slot #4 (secondary EMI) +* 100= Slot #5 (secondary EMI) +* 101= Slot #6 (secondary EMI) +* 110= Slot #7 (secondary EMI) +* 111= Slot #8 (secondary EMI) +*/ +static int lx2160a_qds_get_mdio_mux_val(u8 realbusnum, enum io_slotioslot)
board/freescale/lx2160a/eth_lx2160aqds.c new file +10
-0+{ +switch (realbusnum) { +case EMI1 : +switch (ioslot) { +case EMI1_RGMII1 : +return 0 ; +case EMI1_RGMII2 : +return 0x40 ; +default : + return (((ioslot - 1) << BRDCFG4_EMI1SEL_SHIFT) |
0xC0);board/freescale/lx2160a/eth_lx2160aqds.c new file +16
-0+ } +break ; +case EMI2 : +return ((ioslot -1 ) <<BRDCFG4_EMI2SEL_SHIFT ); +default : +return -1 ; + } +} + +static void lx2160a_qds_mux_mdio (struct lx2160a_qds_mdio *priv) +{ +u8 brdcfg4, mux_val, reg; + + brdcfg4 =QIXIS_READ (brdcfg[4 ]); + reg = brdcfg4; + mux_val = lx2160a_qds_get_mdio_mux_val(priv->realbusnum, priv-Quoted 1 line
ioslot);
board/freescale/lx2160a/eth_lx2160aqds.c new file +34
-0+ +switch (priv->realbusnum) { +case EMI1 : + brdcfg4 &= ~BRDCFG4_EMI1SEL_MASK ; + brdcfg4 |= mux_val; +break ; +case EMI2 : + brdcfg4 &= ~BRDCFG4_EMI2SEL_MASK ; + brdcfg4 |= mux_val; +break ; + } + +if (brdcfg4 ^ reg) +QIXIS_WRITE (brdcfg[4 ], brdcfg4); +} + +static int lx2160a_qds_mdio_read (struct mii_dev *bus,int addr, +int devad,int regnum) +{ +struct lx2160a_qds_mdio *priv = bus->priv; + +lx2160a_qds_mux_mdio (priv); + +return priv->realbus->read (priv->realbus, addr, devad, regnum); +} + +static int lx2160a_qds_mdio_write (struct mii_dev *bus,int addr,int devad, +int regnum,u16 value) +{ +struct lx2160a_qds_mdio *priv = bus->priv; + +lx2160a_qds_mux_mdio (priv); + + return priv->realbus->write(priv->realbus, addr, devad, regnum,value);
board/freescale/lx2160a/eth_lx2160aqds.c new file +10
-0+} + +static int lx2160a_qds_mdio_reset (struct mii_dev *bus) +{ +struct lx2160a_qds_mdio *priv = bus->priv; + +return priv->realbus->reset (priv->realbus); +} + +static struct mii_dev *lx2160a_qds_mdio_init(u8 realbusnum, enum io_slotioslot)
board/freescale/lx2160a/eth_lx2160aqds.c new file +23
-0+{ +struct lx2160a_qds_mdio *pmdio; +struct mii_dev *bus; +/*should be within MDIO_NAME_LEN*/ +char dummy_mdio_name[] ="LX2160A_QDS_MDIO1_IOSLOT1" ; + +if (realbusnum ==EMI2 ) { +if (ioslot <IO_SLOT_1 || ioslot >IO_SLOT_8 ) { +printf ("invalid ioslot %d\n" , ioslot); +return NULL ; + } + }else if (realbusnum ==EMI1 ) { +if (ioslot <IO_SLOT_1 || ioslot >EMI1_RGMII2 ) { +printf ("invalid ioslot %d\n" , ioslot); +return NULL ; + } + }else { +printf ("not supported real mdio bus %d\n" , realbusnum); +return NULL ; + } + +if (ioslot ==EMI1_RGMII1 ) + strcpy(dummy_mdio_name,"
LX2160A_QDS_MDIO1_RGMII1");board/freescale/lx2160a/eth_lx2160aqds.c new file +2
-0+else if (ioslot ==EMI1_RGMII2 ) + strcpy(dummy_mdio_name,"
LX2160A_QDS_MDIO1_RGMII2");board/freescale/lx2160a/eth_lx2160aqds.c new file +2
-0+else + sprintf(dummy_mdio_name,"LX2160A_QDS_MDIO%d_IOSLOT%d",
board/freescale/lx2160a/eth_lx2160aqds.c new file +15
-0+ realbusnum, ioslot); + bus =miiphy_get_dev_by_name (dummy_mdio_name); + +if (bus) +return bus; + + bus =mdio_alloc (); +if (!bus) { +printf ("Failed to allocate %s bus\n" , dummy_mdio_name); +return NULL ; + } + + pmdio =malloc (sizeof (*pmdio)); +if (!pmdio) { + printf("Failed to allocate %s private data\n",
dummy_mdio_name);board/freescale/lx2160a/eth_lx2160aqds.c new file +8
-0+free (bus); +return NULL ; + } + +switch (realbusnum) { +case EMI1 : + pmdio->realbus = +
miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO1_NAME);board/freescale/lx2160a/eth_lx2160aqds.c new file +4
-0+break ; +case EMI2 : + pmdio->realbus = +
miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO2_NAME);board/freescale/lx2160a/eth_lx2160aqds.c new file +40
-0+break ; + } + +if (!pmdio->realbus) { +printf ("No real mdio bus num %d found\n" , realbusnum); +free (bus); +free (pmdio); +return NULL ; + } + + pmdio->realbusnum = realbusnum; + pmdio->ioslot = ioslot; + bus->read = lx2160a_qds_mdio_read; + bus->write = lx2160a_qds_mdio_write; + bus->reset = lx2160a_qds_mdio_reset; +strcpy (bus->name, dummy_mdio_name); + bus->priv = pmdio; + +if (!mdio_register (bus)) +return bus; + +printf ("No bus with name %s\n" , dummy_mdio_name); +free (bus); +free (pmdio); +return NULL ; +} + +static inline void do_phy_config (const struct phy_config *phy_config) +{ +struct mii_dev *bus; +int i, phy_num, phy_address; + +for (i =0 ; i <SRDS_MAX_LANES ; i++) { +if (!phy_config[i].dpmacid) +continue ; + +for (phy_num =0 ; + phy_num <ARRAY_SIZE (phy_config[i].phy_address); + phy_num++) { + phy_address =phy_config[i].phy_address[phy_num];
board/freescale/lx2160a/eth_lx2160aqds.c new file +29
-0+if (phy_address ==-1 ) +break ; +wriop_set_phy_address (phy_config[i].dpmacid, + phy_num, phy_address); + } +/*Register the muxing front-ends to the MDIO buses*/ + bus =lx2160a_qds_mdio_init (phy_config[i].mdio_bus, + phy_config[i].ioslot); +if (!bus) +printf ("could not get bus for mdio %d ioslot %d\n" , + phy_config[i].mdio_bus, + phy_config[i].ioslot); +else +wriop_set_mdio (phy_config[i].dpmacid, bus); + } +} + +static inline void do_dpmac_config (int dpmac,const char *arg_dpmacid, +char *env_dpmac) +{ +const char *ret; +size_t len; +u8 realbusnum, ioslot; +struct mii_dev *bus; +int phy_num; +char *phystr ="phy00" ; + +/*search phy in dpmac arg*/ + for (phy_num = 0; phy_num < WRIOP_MAX_PHY_NUM;phy_num++) {
board/freescale/lx2160a/eth_lx2160aqds.c new file +2
-0+sprintf (phystr,"phy%d" , phy_num +1 ); + ret = hwconfig_subarg_f(arg_dpmacid, phystr, &len,
env_dpmac);board/freescale/lx2160a/eth_lx2160aqds.c new file +4
-0+if (!ret) { +/*look for phy instead of phy1*/ +if (!phy_num) + ret = hwconfig_subarg_f(arg_dpmacid,"phy",
board/freescale/lx2160a/eth_lx2160aqds.c new file +24
-0+ &len, env_dpmac); +if (!ret) +continue ; + } + +if (len !=4 ||strncmp (ret,"0x" ,2 )) +printf ("invalid phy format in %s variable.\n" +"specify phy%d for %s in hex format e.g. 0x12\n" , + env_dpmac, phy_num +1 , arg_dpmacid); +else +wriop_set_phy_address (dpmac, phy_num, +simple_strtoul (ret,NULL ,16 )); + } + +/*search mdio in dpmac arg*/ + ret =hwconfig_subarg_f (arg_dpmacid,"mdio" , &len, env_dpmac); +if (ret) + realbusnum = *ret -'0' ; +else + realbusnum =EMI_NONE ; + +if (realbusnum) { +/*search io in dpmac arg*/ + ret = hwconfig_subarg_f(arg_dpmacid, "io", &len,
env_dpmac);board/freescale/lx2160a/eth_lx2160aqds.c new file +46
-0+if (ret) + ioslot = *ret -'0' ; +else + ioslot =IO_SLOT_NONE ; +/*Register the muxing front-ends to the MDIO buses*/ + bus =lx2160a_qds_mdio_init (realbusnum, ioslot); +if (!bus) +printf ("could not get bus for mdio %d ioslot %d\n" , + realbusnum, ioslot); +else + wriop_set_mdio(dpmac, bus); + } +} + +#endif + +int board_eth_init (bd_t *bis) +{ +#if defined(CONFIG_FSL_MC_ENET ) +struct memac_mdio_info mdio_info; +struct memac_mdio_controller *regs; +int i; +const char *ret; +char *env_dpmac; +char dpmacid[] ="dpmac00" , srds[] ="00_00_00" ; +size_t len; +struct mii_dev *bus; +const struct phy_config *phy_config; +struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR ); +u32 srds_s1, srds_s2, srds_s3; + + srds_s1 =in_le32 (&gur->rcwsr[28 ]) & +FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK ; + srds_s1 >>=FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT ; + + srds_s2 =in_le32 (&gur->rcwsr[28 ]) & +FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK ; + srds_s2 >>=FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT ; + + srds_s3 =in_le32 (&gur->rcwsr[28 ]) & +FSL_CHASSIS3_RCWSR28_SRDS3_PRTCL_MASK ; + srds_s3 >>=FSL_CHASSIS3_RCWSR28_SRDS3_PRTCL_SHIFT ; + +sprintf (srds,"%d_%d_%d" , srds_s1, srds_s2, srds_s3); + + regs = (struct memac_mdio_controller*)CONFIG_SYS_FSL_WRIOP1_MDIO1;
board/freescale/lx2160a/eth_lx2160aqds.c new file +7
-0+ mdio_info.regs = regs; + mdio_info.name =DEFAULT_WRIOP_MDIO1_NAME ; + +/*Register the EMI 1*/ +fm_memac_mdio_init (bis, &mdio_info); + + regs = (struct memac_mdio_controller*)CONFIG_SYS_FSL_WRIOP1_MDIO2;
board/freescale/lx2160a/eth_lx2160aqds.c new file +16
-0+ mdio_info.regs = regs; + mdio_info.name =DEFAULT_WRIOP_MDIO2_NAME ; + +/*Register the EMI 2*/ +fm_memac_mdio_init (bis, &mdio_info); + +/* "dpmac" environment variable can be used after +* defining "dpmac_override" in hwconfig environment variable. +*/ +if (hwconfig ("dpmac_override" )) { + env_dpmac =env_get ("dpmac" ); +if (env_dpmac) { + ret =hwconfig_arg_f ("srds" , &len, env_dpmac); +if (ret) { +if (strncmp (ret, srds,strlen (srds))) { + printf("SERDES configurationchanged.\n"
board/freescale/lx2160a/eth_lx2160aqds.c new file +11
-0+"previous: %.*s, current: %s.\n" +"update dpmac variable.\n" , + (int)len, ret, srds); + } + }else { +printf ("SERDES configuration not found.\n" +"Please add srds:%s in dpmac variable\n" , + srds); + } + + for (i = WRIOP1_DPMAC1; i < NUM_WRIOP_PORTS;i++) {
board/freescale/lx2160a/eth_lx2160aqds.c new file +1
-0+/* Look for dpmac1 to dpmac24(current max) arg
board/freescale/lx2160a/eth_lx2160aqds.c new file +4
-0+* in dpmac environment variable +*/ +sprintf (dpmacid,"dpmac%d" , i); + ret = hwconfig_arg_f(dpmacid, &len,
env_dpmac);board/freescale/lx2160a/eth_lx2160aqds.c new file +2
-0+if (ret) + do_dpmac_config(i, dpmacid,
env_dpmac);board/freescale/lx2160a/eth_lx2160aqds.c new file +11
-0+ } + }else { +printf ("Warning: environment dpmac not found.\n" +"DPAA network interfaces may not work\n" ); + } + }else { +/*Look for phy config for serdes1 in phy config table*/ + phy_config =get_phy_config (srds_s1, serdes1_phy_config, +ARRAY_SIZE (serdes1_phy_config)); +if (!phy_config) { + printf("%s WRIOP: Unsupported SerDes1 Protocol%d\n",
board/freescale/lx2160a/eth_lx2160aqds.c new file +8
-0+ __func__, srds_s1); + }else { +do_phy_config (phy_config); + } + phy_config =get_phy_config (srds_s2, serdes2_phy_config, +ARRAY_SIZE (serdes2_phy_config)); +if (!phy_config) { + printf("%s WRIOP: Unsupported SerDes2 Protocol%d\n",
board/freescale/lx2160a/eth_lx2160aqds.c new file +8
-0+ __func__, srds_s2); + }else { +do_phy_config (phy_config); + } + phy_config =get_phy_config (srds_s3, serdes3_phy_config, +ARRAY_SIZE (serdes3_phy_config)); +if (!phy_config) { + printf("%s WRIOP: Unsupported SerDes3 Protocol%d\n",
board/freescale/lx2160a/eth_lx2160aqds.c new file +7
-0+ __func__, srds_s3); + }else { +do_phy_config (phy_config); + } + } + + if (wriop_get_enet_if(WRIOP1_DPMAC17) ==
PHY_INTERFACE_MODE_RGMII_ID) {board/freescale/lx2160a/eth_lx2160aqds.c new file +1
-0+ wriop_set_phy_address(WRIOP1_DPMAC17, 0,
RGMII_PHY_ADDR1);board/freescale/lx2160a/eth_lx2160aqds.c new file +8
-0+ bus =lx2160a_qds_mdio_init (EMI1 ,EMI1_RGMII1 ); +if (!bus) +printf ("could not get bus for RGMII1\n" ); +else +wriop_set_mdio (WRIOP1_DPMAC17 , bus); + } + + if (wriop_get_enet_if(WRIOP1_DPMAC18) ==
PHY_INTERFACE_MODE_RGMII_ID) {board/freescale/lx2160a/eth_lx2160aqds.c new file +1
-0+ wriop_set_phy_address(WRIOP1_DPMAC18, 0,
RGMII_PHY_ADDR2);board/freescale/lx2160a/eth_lx2160aqds.c new file +36
-0+ bus =lx2160a_qds_mdio_init (EMI1 ,EMI1_RGMII2 ); +if (!bus) +printf ("could not get bus for RGMII2\n" ); +else +wriop_set_mdio (WRIOP1_DPMAC18 , bus); + } + +cpu_eth_init (bis); +#endif /* CONFIG_FMAN_ENET */ + +#ifdef CONFIG_PHY_AQUANTIA +/* +* Export functions to be used by AQ firmware +* upload application +*/ + gd->jt->strcpy = strcpy; + gd->jt->mdelay = mdelay; + gd->jt->mdio_get_current_dev = mdio_get_current_dev; + gd->jt->phy_find_by_mask = phy_find_by_mask; + gd->jt->mdio_phydev_for_ethname = mdio_phydev_for_ethname; + gd->jt->miiphy_set_current_dev = miiphy_set_current_dev; +#endif +return pci_eth_init (bis); +} + +#if defined(CONFIG_RESET_PHY_R ) +void reset_phy (void ) +{ +#if defined(CONFIG_FSL_MC_ENET ) +mc_env_boot (); +#endif +} +#endif /* CONFIG_RESET_PHY_R */ + +#if defined(CONFIG_FSL_MC_ENET ) +int fdt_fixup_dpmac_phy_handle(void *fdt, int dpmac_id, int
node_phandle)board/freescale/lx2160a/eth_lx2160aqds.c new file +26
-0+{ +int offset; +int ret; +char dpmac_str[] ="dpmacs at 00" ; +const char *phy_string; + + offset =fdt_path_offset (fdt,"/soc/fsl-mc/dpmacs" ); + +if (offset <0 ) + offset =fdt_path_offset (fdt,"/fsl-mc/dpmacs" ); + +if (offset <0 ) { +printf ("dpmacs node not found in device tree\n" ); +return offset; + } + +sprintf (dpmac_str,"dpmac@%x" , dpmac_id); +debug ("dpmac_str = %s\n" , dpmac_str); + + offset =fdt_subnode_offset (fdt, offset, dpmac_str); +if (offset <0 ) { +printf ("%s node not found in device tree\n" , dpmac_str); +return offset; + } + + ret = fdt_appendprop_cell(fdt, offset, "phy-handle",
node_phandle);board/freescale/lx2160a/eth_lx2160aqds.c new file +4
-0+if (ret) +printf ("%d@%s %d\n" , __LINE__, __func__, ret); + + phy_string =phy_string_for_interface(wriop_get_enet_if(dpmac_id));
board/freescale/lx2160a/eth_lx2160aqds.c new file +9
-0+ ret =fdt_setprop_string (fdt, offset,"phy-connection-type" , + phy_string); +if (ret) +printf ("%d@%s %d\n" , __LINE__, __func__, ret); + +return ret; +} + +int fdt_get_ioslot_offset(void *fdt, struct mii_dev *mii_dev, int
fpga_offset)board/freescale/lx2160a/eth_lx2160aqds.c new file +26
-0+{ +char mdio_ioslot_str[] ="mdio at 00" ; +char mdio_mux_str[] ="mdio-mux-0" ; +struct lx2160a_qds_mdio *priv; +int offset, mux_val; + +/*Test if the MDIO bus is real mdio bus or muxing front end ?*/ +if (strncmp (mii_dev->name,"LX2160A_QDS_MDIO" , +strlen ("LX2160A_QDS_MDIO" ))) +return -1 ; + +/*Get the real MDIO bus num and ioslot info from bus's priv data*/ + priv = mii_dev->priv; + +debug ("real_bus_num = %d, ioslot = %d\n" , + priv->realbusnum, priv->ioslot); + +sprintf (mdio_mux_str,"mdio-mux-%1d" , priv->realbusnum); + offset =fdt_subnode_offset (fdt, fpga_offset, mdio_mux_str); +if (offset <0 ) { +printf ("%s node not found under node %s in device tree\n" , + mdio_mux_str,fdt_get_name (fdt, fpga_offset,NULL )); +return offset; + } + + mux_val = lx2160a_qds_get_mdio_mux_val(priv->realbusnum, priv-Quoted 1 line
ioslot);
board/freescale/lx2160a/eth_lx2160aqds.c new file +5
-0+sprintf (mdio_ioslot_str,"mdio@%x" , (u8 )mux_val); + + offset =fdt_subnode_offset (fdt, offset, mdio_ioslot_str); +if (offset <0 ) { + printf("%s node not found in device tree\n",
mdio_ioslot_str);board/freescale/lx2160a/eth_lx2160aqds.c new file +7
-0+return offset; + } + +return offset; +} + +int fdt_create_phy_node(void *fdt, int offset, u8 phyaddr, int*subnodeoffset,
board/freescale/lx2160a/eth_lx2160aqds.c new file +28
-0+ struct phy_device *phy_dev, int phandle) +{ + char phy_node_name[] = "ethernet-phy at 00"; +char phy_id_compatible_str[] ="ethernet-phy-id0000.0000" ; +int ret; + +sprintf (phy_node_name,"ethernet-phy@%x" , phyaddr); +debug ("phy_node_name = %s\n" , phy_node_name); + + *subnodeoffset =fdt_add_subnode (fdt, offset, phy_node_name); +if (*subnodeoffset <=0 ) { +printf ("Could not add subnode %s\n" , phy_node_name); +return *subnodeoffset; + } + +sprintf (phy_id_compatible_str,"ethernet-phy-id%04x.%04x" , + phy_dev->phy_id >>16 , phy_dev->phy_id &0xFFFF ); +debug ("phy_id_compatible_str %s\n" , phy_id_compatible_str); + + ret =fdt_setprop_string (fdt, *subnodeoffset,"compatible" , + phy_id_compatible_str); +if (ret) { +printf ("%d@%s %d\n" , __LINE__, __func__, ret); + goto out; + } + + if (phy_dev->is_c45) { + ret = fdt_appendprop_string(fdt, *subnodeoffset,"compatible",
board/freescale/lx2160a/eth_lx2160aqds.c new file +7
-0+ "ethernet-phy-ieee802.3-c45"); +if (ret) { +printf ("%d@%s %d\n" , __LINE__, __func__, ret); + goto out; + } + }else { + ret = fdt_appendprop_string(fdt, *subnodeoffset,"compatible",
board/freescale/lx2160a/eth_lx2160aqds.c new file +38
-0+ "ethernet-phy-ieee802.3-c22"); +if (ret) { +printf ("%d@%s %d\n" , __LINE__, __func__, ret); + goto out; + } + } + + ret =fdt_setprop_cell (fdt, *subnodeoffset,"reg" , phyaddr); +if (ret) { +printf ("%d@%s %d\n" , __LINE__, __func__, ret); + goto out; + } + + ret =fdt_set_phandle (fdt, *subnodeoffset, phandle); +if (ret) { +printf ("%d@%s %d\n" , __LINE__, __func__, ret); + goto out; + } + +out: +if (ret) +fdt_del_node (fdt, *subnodeoffset); + +return ret; +} + +int fdt_fixup_board_phy (void *fdt) +{ +int fpga_offset, offset, subnodeoffset; +struct mii_dev *mii_dev; +struct list_head *mii_devs, *entry; +int ret, dpmac_id, phandle, i; +struct phy_device *phy_dev; +char ethname[ETH_NAME_LEN ]; +phy_interface_t phy_iface; + + ret =0 ; +/* we know FPGA is connected to i2c0, therefore search path directly,
board/freescale/lx2160a/eth_lx2160aqds.c new file +23
-0+* instead of compatible property, as it saves time +*/ + fpga_offset =fdt_path_offset (fdt,"/soc/i2c at 2000000/fpga" ); + +if (fpga_offset <0 ) + fpga_offset =fdt_path_offset (fdt,"/i2c at 2000000/fpga" ); + +if (fpga_offset <0 ) { +printf ("i2c at 2000000/fpga node not found in device tree\n" ); +return fpga_offset; + } + + phandle =fdt_alloc_phandle (fdt); + mii_devs =mdio_get_list_head (); + +list_for_each (entry, mii_devs) { + mii_dev = list_entry(entry, struct mii_dev, link); +debug ("mii_dev name : %s\n" , mii_dev->name); + offset =fdt_get_ioslot_offset (fdt, mii_dev, fpga_offset); +if (offset <0 ) +continue ; + +// Look for phy devices attached to MDIO bus muxing front end
board/freescale/lx2160a/eth_lx2160aqds.c new file +1
-0+// and create their entries with compatible being the device id
board/freescale/lx2160a/eth_lx2160aqds.c new file +10
-0+for (i =0 ; i <PHY_MAX_ADDR ; i++) { + phy_dev = mii_dev->phymap[i]; +if (!phy_dev) +continue ; + +// TODO: use sscanf instead of loop + dpmac_id =WRIOP1_DPMAC1 ; +while (dpmac_id <NUM_WRIOP_PORTS ) { + phy_iface =wriop_get_enet_if (dpmac_id); + snprintf(ethname, ETH_NAME_LEN,"DPMAC%d@%s",
board/freescale/lx2160a/eth_lx2160aqds.c new file +2
-0+ dpmac_id, +
phy_string_for_interface(phy_iface));board/freescale/lx2160a/eth_lx2160aqds.c new file +1
-0+ if (strcmp(ethname, phy_dev->dev->name)== 0)
board/freescale/lx2160a/eth_lx2160aqds.c new file +29
-0+break ; + dpmac_id++; + } +if (dpmac_id ==NUM_WRIOP_PORTS ) +continue ; + + ret =fdt_create_phy_node (fdt, offset, i, + &subnodeoffset, + phy_dev, phandle); +if (ret) +break ; + + ret =fdt_fixup_dpmac_phy_handle (fdt, + dpmac_id, phandle); +if (ret) { +fdt_del_node (fdt, subnodeoffset); +break ; + } + phandle++; + } + +if (ret) +break ; + } + +return ret; +} +#endif // CONFIG_FSL_MC_ENET +board/freescale/lx2160a/lx2160a.c +150
-2@@ -26,6 +26,18 @@#include "../common/vid.h" #include <fsl_immap.h> +#ifdef CONFIG_TARGET_LX2160AQDS +#define CFG_MUX_I2C_SDHC (reg, value) ((reg & 0x3f) | value) +#define SET_CFG_MUX1_SDHC1_SDHC (reg) (reg & 0x3f) +#define SET_CFG_MUX2_SDHC1_SPI (reg, value) ((reg & 0xcf) | value) +#define SET_CFG_MUX3_SDHC1_SPI (reg, value) ((reg & 0xf8) | value) +#define SET_CFG_MUX_SDHC2_DSPI (reg, value) ((reg & 0xf8) | value) +#define SET_CFG_MUX1_SDHC1_DSPI (reg, value) ((reg & 0x3f) | value) +#define SDHC1_BASE_PMUX_DSPI 2 +#define SDHC2_BASE_PMUX_DSPI 2 +#define IIC5_PMUX_SPI3 3 +#endif /* CONFIG_TARGET_LX2160AQDS */ +DECLARE_GLOBAL_DATA_PTR ;static struct pl01x_serial_platdata serial0 = {@@ -85,12 +97,80 @@ int board_early_init_f(void)return 0 ; } +#if defined(CONFIG_TARGET_LX2160AQDS) +void esdhc_dspi_status_fixup(void *blob) +{ + const char esdhc0_path[] = "/soc/esdhc at 2140000"; + const char esdhc1_path[] = "/soc/esdhc at 2150000"; + const char dspi0_path[] = "/soc/dspi at 2100000"; + const char dspi1_path[] = "/soc/dspi at 2110000"; + const char dspi2_path[] = "/soc/dspi at 2120000"; + + struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); + u32 sdhc1_base_pmux; + u32 sdhc2_base_pmux; + u32 iic5_pmux; + + /* Check RCW field sdhc1_base_pmux to enable/disable + * esdhc0/dspi0 DT node + */ + sdhc1_base_pmux = gur_in32(&gur- >rcwsr[FSL_CHASSIS3_RCWSR12_REGSR - 1]) + & FSL_CHASSIS3_SDHC1_BASE_PMUX_MASK; + sdhc1_base_pmux >>= FSL_CHASSIS3_SDHC1_BASE_PMUX_SHIFT; + + if (sdhc1_base_pmux == SDHC1_BASE_PMUX_DSPI) { + do_fixup_by_path(blob, dspi0_path, "status", "okay", + sizeof("okay"), 1); + do_fixup_by_path(blob, esdhc0_path, "status", "disabled", + sizeof("disabled"), 1); + } else { + do_fixup_by_path(blob, esdhc0_path, "status", "okay", + sizeof("okay"), 1); + do_fixup_by_path(blob, dspi0_path, "status", "disabled", + sizeof("disabled"), 1); + } + + /* Check RCW field sdhc2_base_pmux to enable/disable + * esdhc1/dspi1 DT node + */ + sdhc2_base_pmux = gur_in32(&gur- >rcwsr[FSL_CHASSIS3_RCWSR13_REGSR - 1]) + & FSL_CHASSIS3_SDHC2_BASE_PMUX_MASK; + sdhc2_base_pmux >>= FSL_CHASSIS3_SDHC2_BASE_PMUX_SHIFT; + + if (sdhc2_base_pmux == SDHC2_BASE_PMUX_DSPI) { + do_fixup_by_path(blob, dspi1_path, "status", "okay", + sizeof("okay"), 1); + do_fixup_by_path(blob, esdhc1_path, "status", "disabled", + sizeof("disabled"), 1); + } else { + do_fixup_by_path(blob, esdhc1_path, "status", "okay", + sizeof("okay"), 1); + do_fixup_by_path(blob, dspi1_path, "status", "disabled", + sizeof("disabled"), 1); + } + + /* Check RCW field IIC5 to enable dspi2 DT node */ + iic5_pmux = gur_in32(&gur->rcwsr[FSL_CHASSIS3_RCWSR12_REGSR - 1]) + & FSL_CHASSIS3_IIC5_PMUX_MASK; + iic5_pmux >>= FSL_CHASSIS3_IIC5_PMUX_SHIFT; + + if (iic5_pmux == IIC5_PMUX_SPI3) { + do_fixup_by_path(blob, dspi2_path, "status", "okay", + sizeof("okay"), 1); + } +} +#endif + int esdhc_status_fixup(void *blob, const char *compat) { +#if defined(CONFIG_TARGET_LX2160AQDS) + /* Enable esdhc and dspi DT nodes based on RCW fields */ + esdhc_dspi_status_fixup(blob); +#else /* Enable both esdhc DT nodes for LX2160ARDB */ do_fixup_by_compat(blob, compat, "status", "okay", sizeof("okay"), 1); - +#endif return 0; }@@ -107,9 +187,20 @@ int checkboard(void)enum boot_src src =get_boot_src ();char buf[64 ];u8 sw; +#ifdef CONFIG_TARGET_LX2160AQDS +int clock; +static const char *const freq[] = {"100" ,"125" ,"156.25" , +"161.13" ,"322.26" ,"" ,"" ,"" , +"" ,"" ,"" ,"" ,"" ,"" ,"" , +"100 separate SSCG" }; +#endif cpu_name (buf); +#ifdef CONFIG_TARGET_LX2160AQDS +printf ("Board: %s-QDS, " , buf); +#else printf ("Board: %s-RDB, " , buf); +#endif sw =QIXIS_READ (arch);printf ("Board version: %c, boot from " , (sw &0xf ) -1 +'A' );@@ -136,22 +227,206 @@ int checkboard(void)break ; } } +#ifdef CONFIG_TARGET_LX2160AQDS +printf ("FPGA: v%d (%s), build %d" , + (int )QIXIS_READ (scver),qixis_read_tag (buf), + (int )qixis_read_minor ()); +/* the timestamp string contains "\n" at the end */ +printf (" on %s" ,qixis_read_time (buf)); + +puts ("SERDES1 Reference : " ); + sw =QIXIS_READ (brdcfg[2 ]); + clock = sw >>4 ; +printf ("Clock1 = %sMHz " , freq[clock]); + clock = sw &0x0f ; +printf ("Clock2 = %sMHz" , freq[clock]); + + sw =QIXIS_READ (brdcfg[3 ]); +puts ("\nSERDES2 Reference : " ); + clock = sw >>4 ; +printf ("Clock1 = %sMHz " , freq[clock]); + clock = sw &0x0f ; +printf ("Clock2 = %sMHz" , freq[clock]); + + sw =QIXIS_READ (brdcfg[12 ]); +puts ("\nSERDES3 Reference : " ); + clock = sw >>4 ; +printf ("Clock1 = %sMHz Clock2 = %sMHz\n" , freq[clock], freq[clock]); +#else printf ("FPGA: v%d.%d\n" ,QIXIS_READ (scver),QIXIS_READ (tagdata));puts ("SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 161.13MHz\n");puts ("SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz\n" );puts ("SERDES3 Reference: Clock1 = 100MHz Clock2 = 100Hz\n" ); +#endif return 0 ; } +#ifdef CONFIG_TARGET_LX2160AQDS +/* +* implementation of CONFIG_ESDHC_DETECT_QUIRK Macro. +*/ +u8 qixis_esdhc_detect_quirk (void ) +{ +/* for LX2160AQDS res1[1] @ offset 0x1A is SDHC1 Control/Status (SDHC1) +* SDHC1 Card ID: +* Specifies the type of card installed in the SDHC1 adapter slot. +* 000= (reserved) +* 001= eMMC V4.5 adapter is installed. +* 010= SD/MMC 3.3V adapter is installed. +* 011= eMMC V4.4 adapter is installed. +* 100= eMMC V5.0 adapter is installed. +* 101= MMC card/Legacy (3.3V) adapter is installed. +* 110= SDCard V2/V3 adapter installed. +* 111= no adapter is installed. +*/ +return ((QIXIS_READ (res1[1 ]) &QIXIS_SDID_MASK ) != +QIXIS_ESDHC_NO_ADAPTER ); +} + +int config_board_mux (void ) +{ +u8 reg11, reg5, reg13; +struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR ); +u32 sdhc1_base_pmux; +u32 sdhc2_base_pmux; +u32 iic5_pmux; + +/* Routes {I2C2_SCL, I2C2_SDA} to SDHC1 as {SDHC1_CD_B,
SDHC1_WP}.board/freescale/lx2160a/lx2160a.c +1
-0+* Routes {I2C3_SCL, I2C3_SDA} to CAN transceiver as {CAN1_TX,CAN1_RX}.
board/freescale/lx2160a/lx2160a.c +1
-0+* Routes {I2C4_SCL, I2C4_SDA} to CAN transceiver as {CAN2_TX,CAN2_RX}.
board/freescale/lx2160a/lx2160a.c +17
-0+* Qixis and remote systems are isolated from the I2C1 bus. +* Processor connections are still available. +* SPI2 CS2_B controls EN25S64 SPI memory device. +* SPI3 CS2_B controls EN25S64 SPI memory device. +* EC2 connects to PHY #2 using RGMII protocol. +* CLK_OUT connects to FPGA for clock measurement. +*/ + + reg5 =QIXIS_READ (brdcfg[5 ]); + reg5 =CFG_MUX_I2C_SDHC (reg5,0x40 ); +QIXIS_WRITE (brdcfg[5 ], reg5); + +/* Check RCW field sdhc1_base_pmux +* esdhc0 : sdhc1_base_pmux = 0 +* dspi0 : sdhc1_base_pmux = 2 +*/ + sdhc1_base_pmux = gur_in32(&gur-Quoted 1 line
rcwsr[FSL_CHASSIS3_RCWSR12_REGSR - 1])
board/freescale/lx2160a/lx2160a.c +9
-0+ &FSL_CHASSIS3_SDHC1_BASE_PMUX_MASK ; + sdhc1_base_pmux >>=FSL_CHASSIS3_SDHC1_BASE_PMUX_SHIFT ; + +if (sdhc1_base_pmux ==SDHC1_BASE_PMUX_DSPI ) { + reg11 =QIXIS_READ (brdcfg[11 ]); + reg11 =SET_CFG_MUX1_SDHC1_DSPI (reg11,0x40 ); +QIXIS_WRITE (brdcfg[11 ], reg11); + }else { +/* - Routes {SDHC1_CMD, SDHC1_CLK } to SDHC1 adapter slot.
board/freescale/lx2160a/lx2160a.c +13
-0+* {SDHC1_DAT3, SDHC1_DAT2} to SDHC1 adapter slot. +* {SDHC1_DAT1, SDHC1_DAT0} to SDHC1 adapter slot. +*/ + reg11 =QIXIS_READ (brdcfg[11 ]); + reg11 =SET_CFG_MUX1_SDHC1_SDHC (reg11); +QIXIS_WRITE (brdcfg[11 ], reg11); + } + +/* Check RCW field sdhc2_base_pmux +* esdhc1 : sdhc2_base_pmux = 0 (default) +* dspi1 : sdhc2_base_pmux = 2 +*/ + sdhc2_base_pmux = gur_in32(&gur-Quoted 1 line
rcwsr[FSL_CHASSIS3_RCWSR13_REGSR - 1])
board/freescale/lx2160a/lx2160a.c +22
-1+ &FSL_CHASSIS3_SDHC2_BASE_PMUX_MASK ; + sdhc2_base_pmux >>=FSL_CHASSIS3_SDHC2_BASE_PMUX_SHIFT ; + +if (sdhc2_base_pmux ==SDHC2_BASE_PMUX_DSPI ) { + reg13 =QIXIS_READ (brdcfg[13 ]); + reg13 =SET_CFG_MUX_SDHC2_DSPI (reg13,0x01 ); +QIXIS_WRITE (brdcfg[13 ], reg13); + }else { + reg13 =QIXIS_READ (brdcfg[13 ]); + reg13 =SET_CFG_MUX_SDHC2_DSPI (reg13,0x00 ); +QIXIS_WRITE (brdcfg[13 ], reg13); + } + +/* Check RCW field IIC5 to enable dspi2 DT nodei +* dspi2: IIC5 = 3 +*/ + iic5_pmux = gur_in32(&gur->rcwsr[FSL_CHASSIS3_RCWSR12_REGSR - 1]) + & FSL_CHASSIS3_IIC5_PMUX_MASK; + iic5_pmux >>= FSL_CHASSIS3_IIC5_PMUX_SHIFT; + + if (iic5_pmux == IIC5_PMUX_SPI3) { + /* - Routes {SDHC1_DAT4} to SPI3 devices as{
SPI3_M_CS0_B}. */board/freescale/lx2160a/lx2160a.c +7
-0+ reg11 =QIXIS_READ (brdcfg[11 ]); + reg11 =SET_CFG_MUX2_SDHC1_SPI (reg11,0x10 ); +QIXIS_WRITE (brdcfg[11 ], reg11); + +/* - Routes {SDHC1_DAT5, SDHC1_DAT6} nowhere. +* {SDHC1_DAT7, SDHC1_DS } to {nothing, SPI3_M0_CLK }. +* {I2C5_SCL, I2C5_SDA } to {SPI3_M0_MOSI,
SPI3_M0_MISO}.board/freescale/lx2160a/lx2160a.c +11
-0+*/ + reg11 =QIXIS_READ (brdcfg[11 ]); + reg11 =SET_CFG_MUX3_SDHC1_SPI (reg11,0x01 ); +QIXIS_WRITE (brdcfg[11 ], reg11); + }else { +/* Routes {SDHC1_DAT4} to SDHC1 adapter slot */ + reg11 =QIXIS_READ (brdcfg[11 ]); + reg11 =SET_CFG_MUX2_SDHC1_SPI (reg11,0x00 ); +QIXIS_WRITE (brdcfg[11 ], reg11); + +/* - Routes {SDHC1_DAT5, SDHC1_DAT6} to SDHC1 adapter slot.
board/freescale/lx2160a/lx2160a.c +47
-0+* {SDHC1_DAT7, SDHC1_DS } to SDHC1 adapter slot. +* {I2C5_SCL, I2C5_SDA } to SDHC1 adapter slot. +*/ + reg11 =QIXIS_READ (brdcfg[11 ]); + reg11 =SET_CFG_MUX3_SDHC1_SPI (reg11,0x00 ); + QIXIS_WRITE(brdcfg[11], reg11); + } + +return 0 ; +} +#else +int config_board_mux (void ) +{ +return 0 ; +} +#endif +unsigned long get_board_sys_clk (void ) { +#ifdef CONFIG_TARGET_LX2160AQDS +u8 sysclk_conf =QIXIS_READ (brdcfg[1 ]); + +switch (sysclk_conf &0x03 ) { +case QIXIS_SYSCLK_100 : +return 100000000 ; +case QIXIS_SYSCLK_125 : +return 125000000 ; +case QIXIS_SYSCLK_133 : +return 133333333 ; + } +return 100000000 ; +#else return 100000000 ; +#endif }unsigned long get_board_ddr_clk (void ) { +#ifdef CONFIG_TARGET_LX2160AQDS +u8 ddrclk_conf =QIXIS_READ (brdcfg[1 ]); + +switch ((ddrclk_conf &0x30 ) >>4 ) { +case QIXIS_DDRCLK_100 : +return 100000000 ; +case QIXIS_DDRCLK_125 : +return 125000000 ; +case QIXIS_DDRCLK_133 : +return 133333333 ; + } +return 100000000 ; +#else return 100000000 ; +#endif }int board_init (void )@@ -184,6 +459,8 @@ void detail_board_ddr_info(void)#if defined(CONFIG_ARCH_MISC_INIT )int arch_misc_init (void ) { +config_board_mux (); +return 0 ; }#endif configs/lx2160aqds_tfa_defconfig new file +15
-0@@ -0,0 +1,72 @@ +CONFIG_ARM=y +CONFIG_TARGET_LX2160AQDS=y +CONFIG_SYS_TEXT_BASE=0x82000000 +CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y +CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-lx2160a-qds" +CONFIG_NR_DRAM_BANKS=3 +CONFIG_DM=y +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_TFABOOT=y +CONFIG_BOOTDELAY=10 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyAMA0,115200 root=/dev/ram0earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0x2000000 default_hugepagesz=1024m hugepagesz=1024m hugepages=2 pci=pcie_bus_perf"
configs/lx2160aqds_tfa_defconfig new file +57
-0+# CONFIG_USE_BOOTCOMMAND is not set +CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +CONFIG_CMD_CACHE=y +CONFIG_MP=y +CONFIG_OF_CONTROL=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM_SERIAL=y +CONFIG_CONS_INDEX=0 +CONFIG_FSL_CAAM=y +CONFIG_FSL_ESDHC=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_USE_4K_SECTORS=n +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_NXP_FSPI=y +CONFIG_FSPI_AHB_EN_4BYTE=y +CONFIG_SYS_FSPI_AHB_INIT=y +CONFIG_PHYLIB=y +CONFIG_NETDEVICES=y +CONFIG_PHY_GIGE=y +CONFIG_CMD_NET=y +CONFIG_CMD_PING=y +CONFIG_CMD_PXE=y +CONFIG_CMD_MII=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_FAT=y +CONFIG_CMD_EXT2=y +CONFIG_NET=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_STORAGE=y +CONFIG_EFI_LOADER_BOUNCE_BUFFER=y +CONFIG_SCSI_AHCI=y +CONFIG_SCSI=y +# CONFIG_SYS_FSL_DDR_PHY is not set +CONFIG_SYS_GEN2_DDR_PHY=y +CONFIG_SYS_MALLOC_F=y +CONFIG_SYS_MALLOC_F_LEN=0x6000 +CONFIG_PHYLIB_10G=y +CONFIG_PHY_AQUANTIA=y # X-M11-USXGMII +CONFIG_PHY_CORTINA=y # X-M7-40G +CONFIG_PHY_REALTEK=y # RGMII +CONFIG_PHY_INPHI=y # X-M8-100G +CONFIG_PHY_VITESSE=y # SGMII PEX RISER +CONFIG_HUSH_PARSER=yinclude/configs/lx2160aqds.h new file +126
-0@@ -0,0 +1,140 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright 2018-2019 NXP +*/ + +#ifndef __LX2_QDS_H +#define __LX2_QDS_H + +#include "lx2160a_common.h" + +/* Qixis */ +#define QIXIS_XMAP_MASK 0x07 +#define QIXIS_XMAP_SHIFT 5 +#define QIXIS_RST_CTL_RESET_EN 0x30 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_ALTBANK 0x20 +#define QIXIS_LBMAP_QSPI 0x00 +#define QIXIS_RCW_SRC_QSPI 0xff +#define QIXIS_RST_CTL_RESET 0x31 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 +#define QIXIS_LBMAP_MASK 0x0f +#define QIXIS_LBMAP_SD +#define QIXIS_RCW_SRC_SD 0x08 +#define NON_EXTENDED_DUTCFG +#define QIXIS_SDID_MASK 0x07 +#define QIXIS_ESDHC_NO_ADAPTER 0x7 + +/* SYSCLK */ +#define QIXIS_SYSCLK_100 0x0 +#define QIXIS_SYSCLK_125 0x1 +#define QIXIS_SYSCLK_133 0x2 + +/* DDRCLK */ +#define QIXIS_DDRCLK_100 0x0 +#define QIXIS_DDRCLK_125 0x1 +#define QIXIS_DDRCLK_133 0x2 + +#define BRDCFG4_EMI1SEL_MASK 0xF8 +#define BRDCFG4_EMI1SEL_SHIFT 3 +#define BRDCFG4_EMI2SEL_MASK 0x07 +#define BRDCFG4_EMI2SEL_SHIFT 0 + +/* VID */ + +#define I2C_MUX_CH_VOL_MONITOR 0xA +/* Voltage monitor on channel 2*/ +#define I2C_VOL_MONITOR_ADDR 0x63 +#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 +#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 +#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 +#define CONFIG_VID_FLS_ENV "lx2160aqds_vdd_mv" +#define CONFIG_VID + +/* The lowest and highest voltage allowed*/ +#define VDD_MV_MIN 775 +#define VDD_MV_MAX 925 + +/* PM Bus commands code for LTC3882*/ +#define PMBUS_CMD_PAGE 0x0 +#define PMBUS_CMD_READ_VOUT 0x8B +#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 +#define PMBUS_CMD_VOUT_COMMAND 0x21 +#define PWM_CHANNEL0 0x0 + +#define CONFIG_VOL_MONITOR_LTC3882_SET +#define CONFIG_VOL_MONITOR_LTC3882_READ + +/* RTC */ +#define CONFIG_SYS_RTC_BUS_NUM 0 +#define I2C_MUX_CH_RTC 0xB + +/* +* MMC +*/ +#ifdef CONFIG_MMC +#ifndef __ASSEMBLY__ +u8 qixis_esdhc_detect_quirk (void ); +#endif +#define CONFIG_ESDHC_DETECT_QUIRK qixis_esdhc_detect_quirk() +#endif + +/* MAC/PHY configuration */ +#if defined(CONFIG_FSL_MC_ENET ) +#define CONFIG_MII +#define CONFIG_ETHPRIME "DPMAC17 at rgmii-id" + +#define AQ_PHY_ADDR1 0x00 +#define AQ_PHY_ADDR2 0x01 +#define AQ_PHY_ADDR3 0x02 +#define AQ_PHY_ADDR4 0x03 + +#define CORTINA_NO_FW_UPLOAD +#define CORTINA_PHY_ADDR1 0x0 + +#define INPHI_PHY_ADDR1 0x0 +#define INPHI_PHY_ADDR2 0x1 + +#define RGMII_PHY_ADDR1 0x01 +#define RGMII_PHY_ADDR2 0x02 + +#define SGMII_CARD_PORT1_PHY_ADDR 0x1C +#define SGMII_CARD_PORT2_PHY_ADDR 0x1D +#define SGMII_CARD_PORT3_PHY_ADDR 0x1E +#define SGMII_CARD_PORT4_PHY_ADDR 0x1F + +#endif + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + EXTRA_ENV_SETTINGS \ + "lx2160aqds_vdd_mv=800\0" \ + "BOARD=lx2160aqds\0" \ + "xspi_bootcmd=echo Trying load from flexspi..;" \ + "sf probe 0:0 && sf read $load_addr " \ + "$kernel_start $kernel_size ; env exists secureboot &&"\include/configs/lx2160aqds.h new file +2
-0+"sf read $kernelheader_addr_r $kernelheader_start " \ + "$kernelheader_size && esbc_validate${kernelheader_addr_r}; "\
include/configs/lx2160aqds.h new file +5
-0+" bootm $load_addr#$BOARD\0" \ +"sd_bootcmd=echo Trying load from sd card..;" \ +"mmcinfo; mmc read $load_addr " \ +"$kernel_addr_sd $kernel_size_sd ;" \ + "env exists secureboot && mmc read $kernelheader_addr_r"\
include/configs/lx2160aqds.h new file +7
-1+"$kernelhdr_addr_sd $kernelhdr_size_sd " \ +" && esbc_validate ${kernelheader_addr_r};" \ + "bootm $load_addr#$BOARD\0" + +#include <asm/fsl_secure_boot.h> + +#endif /* __LX2_QDS_H */ --2.17.1