Skip to contentSkip to conversation

brcmfmac: improve code handling bandwidth of firmware reported channels

PATCH In review Rafał Miłecki 2 participants 3 messages Feb 11, 2019 – Feb 19, 2019 Broadcom BRCM80211 IEEE802.11 wireless drivers

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 brcmfmac: improve code handling bandwidth of firmware reported channels

From: Rafał Miłecki <[email protected]>

1) Use switch to simplify/improve the code & avoid some duplication
2) Add warning for unsupported values

---
 .../wireless/broadcom/brcm80211/brcmfmac/cfg80211.c | 13 ++++++++++---
 1 file changed, 10 insertions(+), 3 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c +10 -3
index b5e291ed9496..fa752ec04f22 100644
@@ -6049,11 +6049,18 @@ static int brcmf_construct_chaninfo(struct brcmf_cfg80211_info *cfg,
 		/* assuming the chanspecs order is HT20,
 		 * HT40 upper, HT40 lower, and VHT80.
 		 */
-		if (ch.bw == BRCMU_CHAN_BW_80) {
+		switch (ch.bw) {
+		case BRCMU_CHAN_BW_80:
 			channel->flags &= ~IEEE80211_CHAN_NO_80MHZ;
-		} else if (ch.bw == BRCMU_CHAN_BW_40) {
+			break;
+		case BRCMU_CHAN_BW_40:
 			brcmf_update_bw40_channel_flag(channel, &ch);
-		} else {
+			break;
+		default:
+			wiphy_warn(wiphy, "Firmware reported unsupported bandwidth %d\n",
+				   ch.bw);
+			/* fall through */
+		case BRCMU_CHAN_BW_20:
 			/* enable the channel and disable other bandwidths
 			 * for now as mentioned order assure they are enabled
 			 * for subsequent chanspecs.
Signature · 1 line
2.20.1
#1 lore raw

PATCH 2/2 brcmfmac: support firmware reporting 160 MHz channels

From: Rafał Miłecki <[email protected]>

So far 160 MHz channels were treated as 20 MHz ones which was breaking support for 40/80 MHz due to the brcmf_construct_chaninfo() logic and its assumptions.

---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c +3 -0
index fa752ec04f22..b3611f0f68bf 100644
@@ -6050,6 +6050,9 @@ static int brcmf_construct_chaninfo(struct brcmf_cfg80211_info *cfg,
 		 * HT40 upper, HT40 lower, and VHT80.
 		 */
 		switch (ch.bw) {
+		case BRCMU_CHAN_BW_160:
+			channel->flags &= ~IEEE80211_CHAN_NO_160MHZ;
+			break;
 		case BRCMU_CHAN_BW_80:
 			channel->flags &= ~IEEE80211_CHAN_NO_80MHZ;
 			break;
Signature · 1 line
2.20.1
#2 lore raw
In reply to Rafał Miłecki
Quoted 6 lines · Rafał Miłecki

From: Rafał Miłecki <[email protected]>

1) Use switch to simplify/improve the code & avoid some duplication
2) Add warning for unsupported values

2 patches applied to wireless-drivers-next.git, thanks.

f4e183293b87 brcmfmac: improve code handling bandwidth of firmware reported channels 30519cbe339a brcmfmac: support firmware reporting 160 MHz channels

Signature · 3 lines
https://patchwork.kernel.org/patch/10806865/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches