hw/arm/bcm2835_peripherals: add bcm283x sp804-alike timer
Subsystems (2)
PATCH v3 1/1 hw/arm/bcm2835_peripherals: add bcm283x sp804-alike timer
--- hw/arm/bcm2835_peripherals.c | 20 ++ hw/timer/Makefile.objs | 2 + hw/timer/bcm283x_timer.c | 299 +++++++++++++++++++++++++++ include/hw/arm/bcm2835_peripherals.h | 2 + include/hw/timer/bcm283x_timer.h | 38 ++++ 5 files changed, 361 insertions(+) create mode 100644 hw/timer/bcm283x_timer.c create mode 100644 include/hw/timer/bcm283x_timer.h
hw/arm/bcm2835_peripherals.c +20 -0
@@ -117,6 +117,13 @@ static void bcm2835_peripherals_init(Object *obj) OBJECT(&s->sdhci.sdbus), &error_abort);object_property_add_const_link (OBJECT (&s->gpio),"sdbus-sdhost" ,OBJECT (&s->sdhost.sdbus), &error_abort); + +/* SP804-alike ARM Timer */ +object_initialize (&s->bcm283xsp804,sizeof (s->bcm283xsp804), + TYPE_BCM283xSP804); +object_property_add_child (obj,"bcm283xsp804" ,OBJECT (&s->bcm283xsp804), +NULL ); +qdev_set_parent_bus (DEVICE (&s->bcm283xsp804),sysbus_get_default ()); }static void bcm2835_peripherals_realize (DeviceState *dev,Error **errp)
@@ -334,6 +341,19 @@ static void bcm2835_peripherals_realize(DeviceState *dev, Error **errp)error_propagate (errp, err);return ; } + +/* SP804-alike ARM Timer */ +object_property_set_bool (OBJECT (&s->bcm283xsp804), true,"realized" , &err); +if (err) { +error_propagate (errp, err); +return ; + } + +memory_region_add_subregion (&s->peri_mr,ARMCTRL_TIMER0_1_OFFSET , +sysbus_mmio_get_region (SYS_BUS_DEVICE (&s->bcm283xsp804),0 )); +sysbus_connect_irq (SYS_BUS_DEVICE (&s->bcm283xsp804),0 , +qdev_get_gpio_in_named (DEVICE (&s->ic),BCM2835_IC_ARM_IRQ , +INTERRUPT_ARM_TIMER )); }static void bcm2835_peripherals_class_init (ObjectClass *oc,void *data)
hw/timer/Makefile.objs +2 -0
@@ -47,3 +47,5 @@ common-obj-$(CONFIG_SUN4V_RTC) += sun4v-rtc.o common-obj-$(CONFIG_CMSDK_APB_TIMER) += cmsdk-apb-timer.o common-obj-$(CONFIG_CMSDK_APB_DUALTIMER) += cmsdk-apb-dualtimer.o common-obj-$(CONFIG_MSF2) += mss-timer.o + +common-obj-$(CONFIG_RASPI) += bcm283x_timer.o
hw/timer/bcm283x_timer.c new file +299 -0
299 lines not on this page · raw message
include/hw/arm/bcm2835_peripherals.h +2 -0
@@ -23,6 +23,7 @@#include "hw/sd/sdhci.h" #include "hw/sd/bcm2835_sdhost.h" #include "hw/gpio/bcm2835_gpio.h" +#include "hw/timer/bcm283x_timer.h" #define TYPE_BCM2835_PERIPHERALS "bcm2835-peripherals"#define BCM2835_PERIPHERALS (obj) \
@@ -48,6 +49,7 @@ typedef struct BCM2835PeripheralState {SDHCIState sdhci;BCM2835SDHostState sdhost;BCM2835GpioState gpio; + BCM283xSP804State bcm283xsp804; } BCM2835PeripheralState;#endif /* BCM2835_PERIPHERALS_H */
include/hw/timer/bcm283x_timer.h new file +38 -0
@@ -0,0 +1,38 @@ +/* +* Broadcom BCM283x ARM timer variant based on ARM SP804 +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License +* as published by the Free Software Foundation; either version +* 2 of the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License along +* with this program; if not, see <http://www.gnu.org/licenses/>. +*/ +#ifndef HW_TIMER_BCM2835_TIMER_H +#define HW_TIMER_BCM2835_TIMER_H + +#include "hw/sysbus.h" + +#define TYPE_BCM283xSP804 "bcm283xsp804" +#define BCM283xSP804 (obj) \ + OBJECT_CHECK(BCM283xSP804State, (obj), TYPE_BCM283xSP804) + +typedef struct bcm283x_timer_state bcm283x_timer_state ; + +typedef struct { +SysBusDevice parent_obj; + +MemoryRegion iomem; +bcm283x_timer_state *timer; +uint32_t freq0; +int level; +qemu_irq irq; +}BCM283xSP804State ; + +#endif
--
2.20.1
Hi Mark,
Quoted 4 lines
From: Mark <[email protected]>
Sent: Sunday, 10 February 2019 08:58
Subject: [v3 PATCH] hw/arm/bcm2835_peripherals: add bcm283x sp804-alike timer
Thanks for the patch. The integration with bcm2835_peripherals looks good, but hopefully one of the QEMU maintainers can give you a review of the timer implementation as I'm really short on time at the moment.
If you didn't already see it, you may want to compare with the implementation here, which originates from Gregory Estrade:
https://github.com/0xabu/qemu/blob/raspi/hw/timer/bcm2835_timer.c
... sadly I never got around to merging it upstream with the rest of the raspi emulation. ☹
Cheers,
Andrew
Hi Andrew,
Thanks for reviewing the patch I've submitted. I've already messed up two and this is my first time contributing to any open-source software. ☺
I've checked the implementation you suggested and I think it would be a great example for me to implement free-running counters, too.
Best regards,
Mark
Quoted 2 lines · Mark
Signed-off-by Mark <[email protected]>
Hi; thanks for submitting this patch! I have some review comments below. As Andrew suggests, it's probably also a good idea to look at Gregory Estrade's implementation of the timer, to see which is the best basis for a patchset to push upstream.
Quoted 15 lines
--- hw/arm/bcm2835_peripherals.c | 20 ++ hw/timer/Makefile.objs | 2 + hw/timer/bcm283x_timer.c | 299 +++++++++++++++++++++++++++ include/hw/arm/bcm2835_peripherals.h | 2 + include/hw/timer/bcm283x_timer.h | 38 ++++ 5 files changed, 361 insertions(+) create mode 100644 hw/timer/bcm283x_timer.c create mode 100644 include/hw/timer/bcm283x_timer.hhw/arm/bcm2835_peripherals.c +0
-0
hw/arm/bcm2835_peripherals.c static void bcm2835_peripherals_init(Object *obj) · line 126
Quoted 10 lines
hw/arm/bcm2835_peripherals.c +7
-0@@ -117,6 +117,13 @@ static void bcm2835_peripherals_init(Object *obj) OBJECT(&s->sdhci.sdbus), &error_abort);object_property_add_const_link (OBJECT (&s->gpio),"sdbus-sdhost" ,OBJECT (&s->sdhost.sdbus), &error_abort); + +/* SP804-alike ARM Timer */ +object_initialize (&s->bcm283xsp804,sizeof (s->bcm283xsp804), + TYPE_BCM283xSP804); +object_property_add_child (obj,"bcm283xsp804" ,OBJECT (&s->bcm283xsp804), +NULL ); +qdev_set_parent_bus (DEVICE (&s->bcm283xsp804),sysbus_get_default ());
Rather than these three calls, you can do it in one line with
sysbus-init_child_obj(obj, "bcm283xsp804", &s->bcm283xsp804,
sizeof(s->bcm283xsp804), TYPE_BCM283xSP804);hw/timer/Makefile.objs common-obj-$(CONFIG_SUN4V_RTC) += sun4v-rtc.o · line 50
Quoted 9 lines
hw/timer/Makefile.objs +1
-0@@ -47,3 +47,5 @@ common-obj-$(CONFIG_SUN4V_RTC) += sun4v-rtc.o common-obj-$(CONFIG_CMSDK_APB_TIMER) += cmsdk-apb-timer.o common-obj-$(CONFIG_CMSDK_APB_DUALTIMER) += cmsdk-apb-dualtimer.o common-obj-$(CONFIG_MSF2) += mss-timer.o +
Stray blank line.
hw/timer/bcm283x_timer.c
Quoted 7 lines
hw/timer/Makefile.objs +1
-0+common-obj-$(CONFIG_RASPI) += bcm283x_timer.ohw/timer/bcm283x_timer.c new file +0
-0@@ -0,0 +1,299 @@
All new source files in QEMU need to start with a comment that has:
* a brief statement of what the source code is
* a copyright line
* the license that the code is under
Quoted 15 lines
hw/timer/bcm283x_timer.c new file +15
-0+#include "qemu/osdep.h" +#include "hw/sysbus.h" +#include "qemu/timer.h" +#include "qemu-common.h" +#include "hw/qdev.h" +#include "hw/ptimer.h" +#include "hw/timer/bcm283x_timer.h" +#include "qemu/main-loop.h" +#include "qemu/log.h" + +/* TODO: implement free-running timer as per BCM283x peripheral specification */ + +#define TIMER_CTRL_32BIT (1 << 1) +#define TIMER_CTRL_DIV1 (0 << 2) +#define TIMER_CTRL_DIV16 (1 << 2)
hw/timer/bcm283x_timer.c line 25
Quoted 10 lines
hw/timer/bcm283x_timer.c new file +10
-0+#define TIMER_CTRL_DIV256 (2 << 2) +#define TIMER_CTRL_IE (1 << 5) +#define TIMER_CTRL_ENABLE (1 << 7) + +struct bcm283x_timer_state { +ptimer_state *timer; +uint32_t control; +uint32_t limit; +int freq; +int int_level;
In device state structures, types like 'int' don't usually work very well with the VMSTATE_ macros that are used to save and restore state. It's better to use the fixed-width types like uint32_t and int32_t.
hw/timer/bcm283x_timer.c line 31
Quoted 6 lines
hw/timer/bcm283x_timer.c new file +6
-0+qemu_irq irq; +/* Not implemented */ +int prev_div; +/* Not implemented */ +int free_run_cnt; +};
Unlike the SP804, this device has only one timer in it. So I think you'll find it simpler to just drop this struct and put the members directly into the BCM283xSP804State struct.
Quoted 17 lines
hw/timer/bcm283x_timer.c new file +17
-0+ +static void bcm283x_timer_update (bcm283x_timer_state *s) +{ +if (s->int_level && (s->control &TIMER_CTRL_IE )) { +qemu_irq_raise (s->irq); + }else { +qemu_irq_lower (s->irq); + } +} + +static uint32_t bcm283x_timer_read (void *opaque,hwaddr offset) +{ +bcm283x_timer_state *s = (bcm283x_timer_state *) opaque; + +switch (offset >>2 ) { +case 0 :/* Load register */ +case 6 :/* Reload register */
hw/timer/bcm283x_timer.c line 58
Quoted 10 lines
hw/timer/bcm283x_timer.c new file +10
-0+return s->limit; +case 1 :/* Value register */ +return ptimer_get_count (s->timer); +case 2 :/* Control register */ +return s->control; +case 3 :/* IRQ clear/ACK register */ +/* +* The register is write-only, +* but returns reverse "ARMT" string bytes +*/
I was surprised to find that this is actually what the hardware is documented as doing !
Quoted 13 lines
hw/timer/bcm283x_timer.c new file +13
-0+return 0x544D5241 ; +case 4 :/* RAW IRQ register */ +return s->int_level; +case 5 :/* Masked IRQ register */ +if ((s->control &TIMER_CTRL_IE ) ==0 ) { +return 0 ; + } +return s->int_level; +default : +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Bad offset %x\n" , __func__, (int ) offset); +return 0 ; + }
hw/timer/bcm283x_timer.c line 81
Quoted 10 lines
hw/timer/bcm283x_timer.c new file +10
-0+} + +static void bcm283x_timer_recalibrate (bcm283x_timer_state *s,int reload) +{ +uint32_t limit; + +/* Consider timer periodic */ + limit = s->limit; + +ptimer_set_limit (s->timer, limit, reload);
You could just pass s->limit to the function call rather than having a local variable here.
Quoted 87 lines
hw/timer/bcm283x_timer.c new file +87
-0+} + +static void bcm283x_timer_write (void *opaque,hwaddr offset,uint32_t value) +{ +bcm283x_timer_state *s = (bcm283x_timer_state *) opaque; +int freq; + +switch (offset >>2 ) { +case 0 :/* Load register */ + s->limit = value; +bcm283x_timer_recalibrate (s,1 ); +break ; +case 1 :/* Value register */ +/* Read only */ +break ; +case 2 :/* Control register */ +if (s->control &TIMER_CTRL_ENABLE ) { +ptimer_stop (s->timer); + } + + s->control = value; + freq = s->freq; + +/* Set pre-scaler */ +switch ((value >>2 ) &3 ) { +case 1 :/* 16 */ + freq >>=4 ; +break ; +case 2 :/* 256 */ + freq >>=8 ; +break ; + } + +bcm283x_timer_recalibrate (s, s->control &TIMER_CTRL_ENABLE ); +ptimer_set_freq (s->timer, freq); +if (s->control &TIMER_CTRL_ENABLE ) { +ptimer_run (s->timer,0 ); + } +break ; +case 3 :/* IRQ clear/ACK register */ + s->int_level =0 ; +break ; +case 6 :/* Reload register */ + s->limit = value; +bcm283x_timer_recalibrate (s,0 ); +break ; +default : +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Bad offset %x\n" , __func__, (int ) offset); +break ; + } + +bcm283x_timer_update (s); +} + +static void bcm283x_timer_tick (void *opaque) +{ +bcm283x_timer_state *s = (bcm283x_timer_state *) opaque; + s->int_level =1 ; +bcm283x_timer_update (s); +} + +static const VMStateDescription vmstate_bcm283x_timer = { + .name ="bcm283x_timer" , + .version_id =1 , + .minimum_version_id =1 , + .fields = (VMStateField []) { +VMSTATE_UINT32 (control, bcm283x_timer_state), +VMSTATE_UINT32 (limit, bcm283x_timer_state), +VMSTATE_INT32 (int_level, bcm283x_timer_state), +VMSTATE_PTIMER (timer, bcm283x_timer_state), +VMSTATE_END_OF_LIST () + } +}; + +static bcm283x_timer_state *bcm283x_timer_init (uint32_t freq) +{ +bcm283x_timer_state *s; +QEMUBH *bh; + + s =g_new0 (bcm283x_timer_state,1 ); + s->freq = freq; + s->control =TIMER_CTRL_IE ; + + bh =qemu_bh_new (bcm283x_timer_tick, s); + s->timer =ptimer_init (bh,PTIMER_POLICY_DEFAULT ); +vmstate_register (NULL ,-1 , &vmstate_bcm283x_timer, s);
hw/timer/bcm283x_timer.c line 178
Quoted 10 lines
hw/timer/bcm283x_timer.c new file +10
-0+ +return s; +} + +/* BCM283x's implementation of SP804 ARM timer */ + +/* +* XXX: BCM's datasheet does not seem to +* provide these values and they may differ +*/
These ID registers I think do not exist at all. You can tell because the space in the address map for the timer is only 0x400 bytes (the following device, the "SBM", comes after that). So there's no space for the IDs.
Quoted 4 lines
hw/timer/bcm283x_timer.c new file +4
-0+static const uint8_t bcm283xsp803_ids[] = { +/* Timer ID */ +0x04 ,0x18 ,0x14 ,0x00 , +/* PrimeCell ID */
hw/timer/bcm283x_timer.c line 192
Quoted 10 lines
hw/timer/bcm283x_timer.c new file +10
-0+ 0x0D, 0xF0, 0x05, 0xB1 +}; + +static void bcm283xsp804_set_irq (void *opaque,int irq,int level) +{ +BCM283xSP804State *s = (BCM283xSP804State *) opaque; + + s->level = level; +qemu_set_irq (s->irq, s->level); +}
I don't think you need this 'level' field in the struct or this function.
Quoted 8 lines
hw/timer/bcm283x_timer.c new file +8
-0+ +static uint64_t bcm283xsp804_read (void *opaque,hwaddr offset,unsigned size) +{ +BCM283xSP804State *s = (BCM283xSP804State *) opaque; + +if (offset <0x20 ) { +return bcm283x_timer_read (s->timer, offset); + }
hw/timer/bcm283x_timer.c line 210
Quoted 10 lines
hw/timer/bcm283x_timer.c new file +10
-0+/* No second timer (0x20 < offset < 0x40) */ + +if (offset >=0xFE0 && offset <=0xFFC ) { +return bcm283xsp803_ids[(offset -0xFE0 ) >>2 ]; + } + +switch (offset) { +/* Unimplemented: integration test control registers */ +case 0xF00 : +case 0xF04 :
Similarly, these registers can't exist in the bcm2835 timer, because they're off the end of the space available for the device. (So this whole function collapses down to just calling bcm283x_timer_read(), which you can then just put inline in this function, rather than having a separate function. The sp804 code only has the split like this because the sp804 has two identical timer modules in one device.)
hw/timer/bcm283x_timer.c line 223
Quoted 13 lines
hw/timer/bcm283x_timer.c new file +13
-0+qemu_log_mask (LOG_UNIMP , +"%s: integration test registers unimplemented\n" , + __func__); +return 0 ; + } + +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Bad offset %x\n" , __func__, (int ) offset); +return 0 ; +} + +static void bcm283xsp803_write (void *opaque,hwaddr offset,uint64_t value, +unsigned size)
Typo in the function name ('3' instead of '4').
Quoted 40 lines
hw/timer/bcm283x_timer.c new file +40
-0+{ +BCM283xSP804State *s = (BCM283xSP804State *) opaque; + +if (offset <0x20 ) { +bcm283x_timer_write (s->timer, offset, value); + } +/* No second timer (0x20 < offset < 0x40) */ + +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Bad offset %x\n" , __func__, (int ) offset); +} + +static const MemoryRegionOps bcm283xsp804_ops = { + .read = bcm283xsp804_read, + .write = bcm283xsp803_write, + .endianness =DEVICE_NATIVE_ENDIAN +}; + +static const VMStateDescription vmstate_bcm283xsp804 = { + .name ="bcm283xsp804" , + .version_id =1 , + .minimum_version_id =1 , + .fields = (VMStateField []) { +VMSTATE_INT32 (level, BCM283xSP804State), +VMSTATE_END_OF_LIST () + } +}; + +static void bcm283xsp804_init (Object *obj) +{ +BCM283xSP804State *s =BCM283xSP804 (obj); +SysBusDevice *sbd =SYS_BUS_DEVICE (obj); + +sysbus_init_irq (sbd, &s->irq); +memory_region_init_io (&s->iomem, obj, &bcm283xsp804_ops, s, +"bcm283xsp804" ,0x1000 ); + +sysbus_init_mmio (sbd, &s->iomem); +} +
hw/timer/bcm283x_timer.c line 273
Quoted 10 lines
hw/timer/bcm283x_timer.c new file +10
-0+static void bcm283xsp804_realize (DeviceState *dev,Error **errp) +{ +BCM283xSP804State *s =BCM283xSP804 (dev); + + s->timer =bcm283x_timer_init (s->freq0); + s->timer->irq =qemu_allocate_irq (bcm283xsp804_set_irq, s,0 ); +} + +static Property bcm283xsp804_properties[] = { +DEFINE_PROP_UINT32 ("freq0" , BCM283xSP804State, freq0,1000000 ),
The only user of this device doesn't specify the freq0 property, so you might as well not put it in at all. Just use a #define for the frequency. (We can wire it up properly later if we need to.)
hw/timer/bcm283x_timer.c line 283
Quoted 10 lines
hw/timer/bcm283x_timer.c new file +10
-0+ DEFINE_PROP_END_OF_LIST() +}; + +static void bcm283xsp804_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *k =DEVICE_CLASS (klass); + + k->realize = bcm283xsp804_realize; + k->props = bcm283xsp804_properties; + k->vmsd = &vmstate_bcm283xsp804;
You also want a reset function, which should be hooked in via k->reset here.
Quoted 48 lines
hw/timer/bcm283x_timer.c new file +16
-0+} + +static const TypeInfo bcm283xsp804_info = { + .name = TYPE_BCM283xSP804, + .parent =TYPE_SYS_BUS_DEVICE , + .instance_size =sizeof (BCM283xSP804State), + .instance_init = bcm283xsp804_init, + .class_init = bcm283xsp804_class_init +}; + +static void bcm283x_timer_register_types (void ) +{ +type_register_static (&bcm283xsp804_info); +} + +type_init (bcm283x_timer_register_types)include/hw/arm/bcm2835_peripherals.h +2
-0@@ -23,6 +23,7 @@#include "hw/sd/sdhci.h" #include "hw/sd/bcm2835_sdhost.h" #include "hw/gpio/bcm2835_gpio.h" +#include "hw/timer/bcm283x_timer.h" #define TYPE_BCM2835_PERIPHERALS "bcm2835-peripherals"#define BCM2835_PERIPHERALS (obj) \@@ -48,6 +49,7 @@ typedef struct BCM2835PeripheralState {SDHCIState sdhci;BCM2835SDHostState sdhost;BCM2835GpioState gpio; + BCM283xSP804State bcm283xsp804; } BCM2835PeripheralState;#endif /* BCM2835_PERIPHERALS_H */ include/hw/timer/bcm283x_timer.h new file +6
-0@@ -0,0 +1,38 @@ +/* +* Broadcom BCM283x ARM timer variant based on ARM SP804 +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License +* as published by the Free Software Foundation; either version
include/hw/timer/bcm283x_timer.h line 16
Quoted 10 lines
include/hw/timer/bcm283x_timer.h new file +10
-0+* 2 of the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License along +* with this program; if not, see <http://www.gnu.org/licenses/>. +*/
You should put a copyright line in here too.
include/hw/timer/bcm283x_timer.h line 24
Quoted 8 lines
include/hw/timer/bcm283x_timer.h new file +8
-0+#ifndef HW_TIMER_BCM2835_TIMER_H +#define HW_TIMER_BCM2835_TIMER_H + +#include "hw/sysbus.h" + +#define TYPE_BCM283xSP804 "bcm283xsp804" +#define BCM283xSP804 (obj) \ + OBJECT_CHECK(BCM283xSP804State, (obj), TYPE_BCM283xSP804)
I would suggest dropping "SP804" from the name entirely. Then you can have "BCM283xTimerState" for the struct name, TYPE_BCM283x_TIMER for the type name, and so on. This matches better with how we've named the other devices in the SoC.
include/hw/timer/bcm283x_timer.h line 36
Quoted 12 lines
include/hw/timer/bcm283x_timer.h new file +12
-0+ +typedef struct bcm283x_timer_state bcm283x_timer_state ; + +typedef struct { +SysBusDevice parent_obj; + +MemoryRegion iomem; +bcm283x_timer_state *timer; +uint32_t freq0; +int level; +qemu_irq irq; +}BCM283xSP804State ;
thanks
-- PMM