Skip to contentSkip to conversation

ARM: dts: exynos: Add CPU cooling on Arndale Octa

PATCH New Krzysztof Kozlowski 1 participant 2 messages Feb 18, 2019

Subsystems (2)
lore
Share & tools
lore

Krzysztof Kozlowski

author maintainer
#0 lore raw

PATCH 1/2 ARM: dts: exynos: Add CPU cooling on Arndale Octa

Arndale Octa board comes without fan so proper CPU cooling is necessary to avoid critical shutdowns when CPUs are busy. Although thermal zones were present but CPU cooling was missing in DTS.

Adjust the trip points and add respective cooling nodes for each CPU thermal zone. The CPU throttling will start at 60 degrees of C, intensify at 80 degrees of C and slow down CPUs as much as possible at 110 degrees of C.

With this configuration, when running four CPU intensive tasks, the temperatures did not exceed 90 degrees of Celsius mostly oscillating around 88 degrees in hottest thermal zone. Test was however done with only four CPUs online (big cluster, Cortex A15) because of errors when booting secondary CPUs.

---
 arch/arm/boot/dts/exynos5420-arndale-octa.dts | 264 ++++++++++++++++++
 1 file changed, 264 insertions(+)
arch/arm/boot/dts/exynos5420-arndale-octa.dts +264 -0
index c7d9604a119e..2b227246c685 100644
@@ -59,6 +59,270 @@
 	cpu-supply = <&buck6_reg>;
 };
 
+&cpu0_thermal {
+	trips {
+		cpu0_alert0: cpu-alert-0 {
+			temperature = <60000>; /* millicelsius */
+			hysteresis = <5000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu0_alert1: cpu-alert-1 {
+			temperature = <80000>; /* millicelsius */
+			hysteresis = <10000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu0_alert2: cpu-alert-2 {
+			temperature = <110000>; /* millicelsius */
+			hysteresis = <10000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu0_crit0: cpu-crit-0 {
+			temperature = <120000>; /* millicelsius */
+			hysteresis = <0>; /* millicelsius */
+			type = "critical";
+		};
+	};
+
+	cooling-maps {
+		/*
+		 * Reduce the CPU speed by 2 steps, down to: 1600 MHz
+		 * and 1100 MHz.
+		 */
+		map0 {
+			trip = <&cpu0_alert0>;
+			cooling-device = <&cpu0 0 2>,
+					 <&cpu1 0 2>,
+					 <&cpu2 0 2>,
+					 <&cpu3 0 2>,
+					 <&cpu4 0 2>,
+					 <&cpu5 0 2>,
+					 <&cpu6 0 2>,
+					 <&cpu7 0 2>;
+		};
+
+		/*
+		 * Reduce the CPU speed down to 1200 MHz big (6 steps)
+		 * and 800 MHz LITTLE (5 steps).
+		 */
+		map1 {
+			trip = <&cpu0_alert1>;
+			cooling-device = <&cpu0 3 6>,
+					 <&cpu1 3 6>,
+					 <&cpu2 3 6>,
+					 <&cpu3 3 6>,
+					 <&cpu4 3 5>,
+					 <&cpu5 3 5>,
+					 <&cpu6 3 5>,
+					 <&cpu7 3 5>;
+		};
+
+		/*
+		 * Reduce the CPU speed as much as possible, down to 700 MHz
+		 * big (11 steps) and 600 MHz LITTLE (7 steps).
+		 */
+		map2 {
+			trip = <&cpu0_alert2>;
+			cooling-device = <&cpu0 6 11>,
+					 <&cpu1 6 11>,
+					 <&cpu2 6 11>,
+					 <&cpu3 6 11>,
+					 <&cpu4 5 7>,
+					 <&cpu5 5 7>,
+					 <&cpu6 5 7>,
+					 <&cpu7 5 7>;
+		};
+	};
+};
+
+&cpu1_thermal {
+	trips {
+		cpu1_alert0: cpu-alert-0 {
+			temperature = <60000>; /* millicelsius */
+			hysteresis = <5000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu1_alert1: cpu-alert-1 {
+			temperature = <80000>; /* millicelsius */
+			hysteresis = <10000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu1_alert2: cpu-alert-2 {
+			temperature = <110000>; /* millicelsius */
+			hysteresis = <10000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu1_crit0: cpu-crit-0 {
+			temperature = <120000>; /* millicelsius */
+			hysteresis = <0>; /* millicelsius */
+			type = "critical";
+		};
+	};
+
+	cooling-maps {
+		map0 {
+			trip = <&cpu1_alert0>;
+			cooling-device = <&cpu0 0 2>,
+					 <&cpu1 0 2>,
+					 <&cpu2 0 2>,
+					 <&cpu3 0 2>,
+					 <&cpu4 0 2>,
+					 <&cpu5 0 2>,
+					 <&cpu6 0 2>,
+					 <&cpu7 0 2>;
+		};
+
+		map1 {
+			trip = <&cpu1_alert1>;
+			cooling-device = <&cpu0 3 6>,
+					 <&cpu1 3 6>,
+					 <&cpu2 3 6>,
+					 <&cpu3 3 6>,
+					 <&cpu4 3 5>,
+					 <&cpu5 3 5>,
+					 <&cpu6 3 5>,
+					 <&cpu7 3 5>;
+		};
+
+		map2 {
+			trip = <&cpu1_alert2>;
+			cooling-device = <&cpu0 6 11>,
+					 <&cpu1 6 11>,
+					 <&cpu2 6 11>,
+					 <&cpu3 6 11>,
+					 <&cpu4 5 7>,
+					 <&cpu5 5 7>,
+					 <&cpu6 5 7>,
+					 <&cpu7 5 7>;
+		};
+	};
+};
+
+&cpu2_thermal {
+	trips {
+		cpu2_alert0: cpu-alert-0 {
+			temperature = <60000>; /* millicelsius */
+			hysteresis = <5000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu2_alert1: cpu-alert-1 {
+			temperature = <80000>; /* millicelsius */
+			hysteresis = <10000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu2_alert2: cpu-alert-2 {
+			temperature = <110000>; /* millicelsius */
+			hysteresis = <10000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu2_crit0: cpu-crit-0 {
+			temperature = <120000>; /* millicelsius */
+			hysteresis = <0>; /* millicelsius */
+			type = "critical";
+		};
+	};
+
+	cooling-maps {
+		map0 {
+			trip = <&cpu2_alert0>;
+			cooling-device = <&cpu0 0 2>,
+					 <&cpu1 0 2>,
+					 <&cpu2 0 2>,
+					 <&cpu3 0 2>,
+					 <&cpu4 0 2>,
+					 <&cpu5 0 2>,
+					 <&cpu6 0 2>,
+					 <&cpu7 0 2>;
+		};
+
+		map1 {
+			trip = <&cpu2_alert1>;
+			cooling-device = <&cpu0 3 6>,
+					 <&cpu1 3 6>,
+					 <&cpu2 3 6>,
+					 <&cpu3 3 6>,
+					 <&cpu4 3 5>,
+					 <&cpu5 3 5>,
+					 <&cpu6 3 5>,
+					 <&cpu7 3 5>;
+		};
+
+		map2 {
+			trip = <&cpu2_alert2>;
+			cooling-device = <&cpu0 6 11>,
+					 <&cpu1 6 11>,
+					 <&cpu2 6 11>,
+					 <&cpu3 6 11>,
+					 <&cpu4 6 7>,
+					 <&cpu5 6 7>,
+					 <&cpu6 6 7>,
+					 <&cpu7 6 7>;
+		};
+	};
+};
+
+&cpu3_thermal {
+	trips {
+		cpu3_alert0: cpu-alert-0 {
+			temperature = <60000>; /* millicelsius */
+			hysteresis = <5000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu3_alert1: cpu-alert-1 {
+			temperature = <80000>; /* millicelsius */
+			hysteresis = <10000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu3_alert2: cpu-alert-2 {
+			temperature = <110000>; /* millicelsius */
+			hysteresis = <10000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu3_crit0: cpu-crit-0 {
+			temperature = <120000>; /* millicelsius */
+			hysteresis = <0>; /* millicelsius */
+			type = "critical";
+		};
+	};
+
+	cooling-maps {
+		map0 {
+			trip = <&cpu3_alert0>;
+			cooling-device = <&cpu0 0 2>,
+					 <&cpu1 0 2>,
+					 <&cpu2 0 2>,
+					 <&cpu3 0 2>,
+					 <&cpu4 0 2>,
+					 <&cpu5 0 2>,
+					 <&cpu6 0 2>,
+					 <&cpu7 0 2>;
+		};
+
+		map1 {
+			trip = <&cpu3_alert1>;
+			cooling-device = <&cpu0 3 6>,
+					 <&cpu1 3 6>,
+					 <&cpu2 3 6>,
+					 <&cpu3 3 6>,
+					 <&cpu4 3 5>,
+					 <&cpu5 3 5>,
+					 <&cpu6 3 5>,
+					 <&cpu7 3 5>;
+		};
+
+		map2 {
+			trip = <&cpu3_alert2>;
+			cooling-device = <&cpu0 6 11>,
+					 <&cpu1 6 11>,
+					 <&cpu2 6 11>,
+					 <&cpu3 6 11>,
+					 <&cpu4 5 7>,
+					 <&cpu5 5 7>,
+					 <&cpu6 5 7>,
+					 <&cpu7 5 7>;
+		};
+	};
+};
+
 &usbdrd_dwc3_1 {
 	dr_mode = "host";
 };
Signature · 1 line
2.17.1
author maintainer
#1 lore raw

PATCH 2/2 ARM: dts: exynos: Order nodes alphabetically in Arndale Octa

Having nodes and overrides-by-label ordered alphabetically reduces the possibility of conflicts from simultaneous edits. No functional change.

---
 arch/arm/boot/dts/exynos5420-arndale-octa.dts | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)
arch/arm/boot/dts/exynos5420-arndale-octa.dts +8 -8
index 2b227246c685..6b4bf5ee2e45 100644
@@ -51,6 +51,10 @@
 	};
 };
 
+&cci {
+	status = "disabled";
+};
+
 &cpu0 {
 	cpu-supply = <&buck2_reg>;
 };
@@ -323,14 +327,6 @@
 	};
 };
 
-&usbdrd_dwc3_1 {
-	dr_mode = "host";
-};
-
-&cci {
-	status = "disabled";
-};
-
 &hdmi {
 	hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
 	vdd_osc-supply = <&ldo7_reg>;
@@ -724,3 +720,7 @@
 	clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
 	clock-names = "rtc", "rtc_src";
 };
+
+&usbdrd_dwc3_1 {
+	dr_mode = "host";
+};
Signature · 1 line
2.17.1