configs/zynq_zybo: remove defconfig
PATCH 1/1 configs/zynq_zybo: remove defconfig
This defconfig was added in October 2016 and was never updated since then. It currently fails to build because U-Boot is too old and doesn't build with host-openssl in version 1.1.x.
On February 13, 2019, the original submitter was notified, but didn't reply, so let's remove the defconfig for this platform.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/165766194
--- .gitlab-ci.yml | 1 - DEVELOPERS | 4 -- board/digilent/zybo/genimage.cfg | 29 ------------ board/digilent/zybo/post-image.sh | 18 -------- board/digilent/zybo/readme.txt | 76 ------------------------------- board/digilent/zybo/system.bit | 0 board/digilent/zybo/uEnv.txt | 5 -- configs/zynq_zybo_defconfig | 30 ------------ 8 files changed, 163 deletions(-) delete mode 100644 board/digilent/zybo/genimage.cfg delete mode 100755 board/digilent/zybo/post-image.sh delete mode 100644 board/digilent/zybo/readme.txt delete mode 100644 board/digilent/zybo/system.bit delete mode 100644 board/digilent/zybo/uEnv.txt delete mode 100644 configs/zynq_zybo_defconfig
.gitlab-ci.yml +0 -1
@@ -276,7 +276,6 @@ warpboard_defconfig: { extends: .defconfig } zynq_microzed_defconfig: { extends: .defconfig } zynq_zc706_defconfig: { extends: .defconfig } zynq_zed_defconfig: { extends: .defconfig } -zynq_zybo_defconfig: { extends: .defconfig } zynqmp_zcu106_defconfig: { extends: .defconfig } tests.boot.test_atf.TestATFAllwinner: { extends: .runtime_test } tests.boot.test_atf.TestATFMarvell: { extends: .runtime_test }
DEVELOPERS +0 -4
@@ -1925,10 +1925,6 @@ F: package/python-flask-jsonrpc/ F: package/python-flask-login/ F: package/qt5/qt5charts/ -N: Sebastien Van Cauwenberghe <[email protected]> -F: board/digilent/zybo/ -F: configs/zynq_zybo_defconfig - N: Semyon Kolganov <[email protected]> F: package/fmt/ F: package/libbson/
board/digilent/zybo/genimage.cfg deleted +0 -29
@@ -1,29 +0,0 @@ -image boot.vfat { - vfat { - files = { - "BOOT.BIN", - "uEnv.txt", - "system.bit", - "zynq-zybo.dtb", - "u-boot-dtb.img", - "uImage" - } - } - size = 32M -} - -image sdcard.img { - hdimage { - } - - partition boot { - partition-type = 0xC - bootable = "true" - image = "boot.vfat" - } - - partition rootfs { - partition-type = 0x83 - image = "rootfs.ext4" - } -}
board/digilent/zybo/post-image.sh deleted +0 -18
@@ -1,18 +0,0 @@ -#!/bin/sh - -BOARD_DIR="$(dirname $0)" -GENIMAGE_CFG="${BOARD_DIR}/genimage.cfg" -GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp" -OUTPUT_DIR="${O}/images" - -rm -rf "${GENIMAGE_TMP}" - -cp board/digilent/zybo/uEnv.txt ${BINARIES_DIR} -cp board/digilent/zybo/system.bit ${BINARIES_DIR} - -genimage \ - --rootpath "${TARGET_DIR}" \ - --tmppath "${GENIMAGE_TMP}" \ - --inputpath "${BINARIES_DIR}" \ - --outputpath "${BINARIES_DIR}" \ - --config "${GENIMAGE_CFG}"
board/digilent/zybo/readme.txt deleted +0 -76
76 lines not on this page · raw message
board/digilent/zybo/system.bit deleted +0 -0
board/digilent/zybo/uEnv.txt deleted +0 -5
@@ -1,5 +0,0 @@ -bootargs=root=/dev/mmcblk0p2 rootwait rw rootfstype=ext4 -fpga_image=system.bit -fpgaboot=if fatload mmc 0 0x1000000 ${fpga_image}; then echo Booting FPGA from ${fpga_image}; fpga info 0 && fpga loadb 0 0x1000000 $filesize; else echo FPGA image ${fpga_image} was not found, skipping...; fi; -kernel_image=uImage -sdboot=echo Booting from SD...; run fpgaboot; fatload mmc 0 0x1000000 ${kernel_image} && fatload mmc 0 0x2000000 zynq-zybo.dtb && bootm 0x1000000 - 0x2000000
configs/zynq_zybo_defconfig deleted +0 -30
@@ -1,30 +0,0 @@ -BR2_arm=y -BR2_cortex_a9=y -BR2_ARM_ENABLE_NEON=y -BR2_ARM_ENABLE_VFP=y -BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_6=y -BR2_TARGET_GENERIC_GETTY_PORT="ttyPS0" -BR2_ROOTFS_POST_IMAGE_SCRIPT="board/digilent/zybo/post-image.sh" -BR2_LINUX_KERNEL=y -BR2_LINUX_KERNEL_CUSTOM_VERSION=y -BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.6.4" -BR2_LINUX_KERNEL_DEFCONFIG="multi_v7" -BR2_LINUX_KERNEL_UIMAGE=y -BR2_LINUX_KERNEL_UIMAGE_LOADADDR="0x8000" -BR2_LINUX_KERNEL_DTS_SUPPORT=y -BR2_LINUX_KERNEL_INTREE_DTS_NAME="zynq-zybo" -BR2_TARGET_ROOTFS_EXT2=y -BR2_TARGET_ROOTFS_EXT2_4=y -BR2_TARGET_UBOOT=y -BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y -BR2_TARGET_UBOOT_CUSTOM_VERSION=y -BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2016.05" -BR2_TARGET_UBOOT_BOARD_DEFCONFIG="zynq_zybo" -BR2_TARGET_UBOOT_NEEDS_DTC=y -BR2_TARGET_UBOOT_NEEDS_OPENSSL=y -BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y -BR2_TARGET_UBOOT_SPL=y -BR2_TARGET_UBOOT_ZYNQ_IMAGE=y -BR2_PACKAGE_HOST_DOSFSTOOLS=y -BR2_PACKAGE_HOST_GENIMAGE=y -BR2_PACKAGE_HOST_MTOOLS=y
Signature · 1 line
2.20.1
PATCH 1/1 configs/zynq_zybo: remove defconfig
Quoted 4 lines · Thomas Petazzoni
This defconfig was added in October 2016 and was never updated since then. It currently fails to build because U-Boot is too old and doesn't build with host-openssl in version 1.1.x.
You can probably just replace uboot with this version
https://github.com/Xilinx/u-boot-xlnx/tree/xilinx-v2018.3 for xilinx devices like these.
Quoted 251 lines
On February 13, 2019, the original submitter was notified, but didn't reply, so let's remove the defconfig for this platform.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/165766194
Signed-off-by Thomas Petazzoni <[email protected]>--- .gitlab-ci.yml | 1 - DEVELOPERS | 4 -- board/digilent/zybo/genimage.cfg | 29 ------------ board/digilent/zybo/post-image.sh | 18 -------- board/digilent/zybo/readme.txt | 76 ------------------------------- board/digilent/zybo/system.bit | 0 board/digilent/zybo/uEnv.txt | 5 -- configs/zynq_zybo_defconfig | 30 ------------ 8 files changed, 163 deletions(-) delete mode 100644 board/digilent/zybo/genimage.cfg delete mode 100755 board/digilent/zybo/post-image.sh delete mode 100644 board/digilent/zybo/readme.txt delete mode 100644 board/digilent/zybo/system.bit delete mode 100644 board/digilent/zybo/uEnv.txt delete mode 100644 configs/zynq_zybo_defconfig.gitlab-ci.yml +0
-1@@ -276,7 +276,6 @@ warpboard_defconfig: { extends: .defconfig } zynq_microzed_defconfig: { extends: .defconfig } zynq_zc706_defconfig: { extends: .defconfig } zynq_zed_defconfig: { extends: .defconfig } -zynq_zybo_defconfig: { extends: .defconfig } zynqmp_zcu106_defconfig: { extends: .defconfig } tests.boot.test_atf.TestATFAllwinner: { extends: .runtime_test } tests.boot.test_atf.TestATFMarvell: { extends: .runtime_test }DEVELOPERS +0
-4@@ -1925,10 +1925,6 @@ F: package/python-flask-jsonrpc/ F: package/python-flask-login/ F: package/qt5/qt5charts/ -N: Sebastien Van Cauwenberghe <[email protected]> -F: board/digilent/zybo/ -F: configs/zynq_zybo_defconfig - N: Semyon Kolganov <[email protected]> F: package/fmt/ F: package/libbson/board/digilent/zybo/genimage.cfg deleted +0
-29@@ -1,29 +0,0 @@ -image boot.vfat { - vfat { - files = { - "BOOT.BIN", - "uEnv.txt", - "system.bit", - "zynq-zybo.dtb", - "u-boot-dtb.img", - "uImage" - } - } - size = 32M -} - -image sdcard.img { - hdimage { - } - - partition boot { - partition-type = 0xC - bootable = "true" - image = "boot.vfat" - } - - partition rootfs { - partition-type = 0x83 - image = "rootfs.ext4" - } -}board/digilent/zybo/post-image.sh deleted +0
-18@@ -1,18 +0,0 @@ -#!/bin/sh - -BOARD_DIR="$(dirname $0)" -GENIMAGE_CFG="${BOARD_DIR}/genimage.cfg" -GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp" -OUTPUT_DIR="${O}/images" - -rm -rf "${GENIMAGE_TMP}" - -cp board/digilent/zybo/uEnv.txt ${BINARIES_DIR} -cp board/digilent/zybo/system.bit ${BINARIES_DIR} - -genimage \ - --rootpath "${TARGET_DIR}" \ - --tmppath "${GENIMAGE_TMP}" \ - --inputpath "${BINARIES_DIR}" \ - --outputpath "${BINARIES_DIR}" \ - --config "${GENIMAGE_CFG}"board/digilent/zybo/readme.txt deleted +0
-76@@ -1,76 +0,0 @@ -Digilent Zybo -============= - -This is the Buildroot board support for the Digilent Zybo. The Zybo is -a development board based on the Xilinx Zynq-7000 based All-Programmable -System-On-Chip. - -Zybo information including schematics, reference designs, and manuals are -available from http://store.digilentinc.com/zybo-zynq-7000-arm-fpga-soc-trainer-board/ . - -If you want a custom FPGA bitstream to be loaded by U-Boot, copy it as -system.bit in board/digilent/zybo/. - -Steps to create a working system for Zybo: - -1) make zynq_zybo_defconfig -2) make -3) write your SD Card with the sdcard.img file using dd by doing - $ sudo dd if=output/images/sdcard.img of=/dev/sdX -4) insert the SD Card and power up your Zybo -5) Expect serial console on the second USB serial port exposed by the board - -The expected output: - - U-Boot SPL 2016.05 (May 20 2016 - 16:16:24) - mmc boot - Trying to boot from MMC1 - reading system.dtb - spl_load_image_fat_os: error reading image system.dtb, err - -1 - reading u-boot-dtb.img - reading u-boot-dtb.img - - - U-Boot 2016.05 (May 20 2016 - 16:16:24 +0200) - - Model: Zynq ZYBO Development Board - Board: Xilinx Zynq - I2C: ready - DRAM: ECC disabled 512 MiB - MMC: sdhci at e0100000: 0 - SF: Detected S25FL128S_64K with page size 256 Bytes, erase size 64 KiB, total 16 MiB - In: serial at e0001000 - Out: serial at e0001000 - Err: serial at e0001000 - Model: Zynq ZYBO Development Board - Board: Xilinx Zynq - Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id - I2C EEPROM MAC address read failed - - Warning: ethernet at e000b000 (eth0) using random MAC address - 56:64:dd:a7:6d:94 - eth0: ethernet at e000b000 - ... - -Resulting system ----------------- -Once the build process is finished you will have an image called "sdcard.img" -in the output/images/ directory. - -The first partition is a FAT32 partition created at the beginning of the SD Card -that contains the following files : - /BOOT.BIN - /zynq-zybo.dtb - /uEnv.txt - /system.bit - /uImage - /u-boot-dtb.img - -The second partition is an ext4 partition that contains the root filesystem. - -You can alter the booting procedure by modifying the uEnv.txt file -in first partition of the SD card. It is a plain text file in format -<key>=<value> one per line: - -kernel_image=myimage -modeboot=myboot -myboot=...board/digilent/zybo/system.bit deleted +0
-0board/digilent/zybo/uEnv.txt deleted +0
-5@@ -1,5 +0,0 @@ -bootargs=root=/dev/mmcblk0p2 rootwait rw rootfstype=ext4 -fpga_image=system.bit -fpgaboot=if fatload mmc 0 0x1000000 ${fpga_image}; then echo Booting FPGA from ${fpga_image}; fpga info 0 && fpga loadb 0 0x1000000 $filesize; else echo FPGA image ${fpga_image} was not found, skipping...; fi; -kernel_image=uImage -sdboot=echo Booting from SD...; run fpgaboot; fatload mmc 0 0x1000000 ${kernel_image} && fatload mmc 0 0x2000000 zynq-zybo.dtb && bootm 0x1000000 - 0x2000000configs/zynq_zybo_defconfig deleted +0
-31@@ -1,30 +0,0 @@ -BR2_arm=y -BR2_cortex_a9=y -BR2_ARM_ENABLE_NEON=y -BR2_ARM_ENABLE_VFP=y -BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_6=y -BR2_TARGET_GENERIC_GETTY_PORT="ttyPS0" -BR2_ROOTFS_POST_IMAGE_SCRIPT="board/digilent/zybo/post-image.sh" -BR2_LINUX_KERNEL=y -BR2_LINUX_KERNEL_CUSTOM_VERSION=y -BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.6.4" -BR2_LINUX_KERNEL_DEFCONFIG="multi_v7" -BR2_LINUX_KERNEL_UIMAGE=y -BR2_LINUX_KERNEL_UIMAGE_LOADADDR="0x8000" -BR2_LINUX_KERNEL_DTS_SUPPORT=y -BR2_LINUX_KERNEL_INTREE_DTS_NAME="zynq-zybo" -BR2_TARGET_ROOTFS_EXT2=y -BR2_TARGET_ROOTFS_EXT2_4=y -BR2_TARGET_UBOOT=y -BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y -BR2_TARGET_UBOOT_CUSTOM_VERSION=y -BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2016.05" -BR2_TARGET_UBOOT_BOARD_DEFCONFIG="zynq_zybo" -BR2_TARGET_UBOOT_NEEDS_DTC=y -BR2_TARGET_UBOOT_NEEDS_OPENSSL=y -BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y -BR2_TARGET_UBOOT_SPL=y -BR2_TARGET_UBOOT_ZYNQ_IMAGE=y -BR2_PACKAGE_HOST_DOSFSTOOLS=y -BR2_PACKAGE_HOST_GENIMAGE=y -BR2_PACKAGE_HOST_MTOOLS=y --2.20.1
_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot
PATCH 1/1 configs/zynq_zybo: remove defconfig
Hello,
Quoted 9 lines · On Fri, 22 Feb 2019 13:54:11 -0700 James Hilliard <[email protected]>…
Quoted 4 lines · Thomas Petazzoni
This defconfig was added in October 2016 and was never updated since then. It currently fails to build because U-Boot is too old and doesn't build with host-openssl in version 1.1.x.
You can probably just replace uboot with this version
https://github.com/Xilinx/u-boot-xlnx/tree/xilinx-v2018.3 for xilinx devices like these.
I'm pretty sure mainline U-Boot has support for this board, so it's not really the problem. The thing is that defconfigs are meant to be tested on real HW. Since I don't have this HW, and the original submitter didn't reply, there is not much I can do except suggesting to drop the defconfig. Either someone with the HW platform steps in, fixes the build issue and checks that the new U-Boot version runs OK on the HW, or we simply drop the defconfig.
Best regards,
Thomas
Signature · 3 lines
Thomas Petazzoni, CTO, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
PATCH 1/1 configs/zynq_zybo: remove defconfig
In reply to James HilliardQuoted 11 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
"James" == James Hilliard <[email protected]> writes:
Quoted 4 lines · Thomas Petazzoni
This defconfig was added in October 2016 and was never updated since then. It currently fails to build because U-Boot is too old and doesn't build with host-openssl in version 1.1.x.
You can probably just replace uboot with this version
https://github.com/Xilinx/u-boot-xlnx/tree/xilinx-v2018.3 for xilinx devices like these.
Possibly, but if nobody has access to and is interesting in maintaining this defconfig, then it makes more sense to remove it.
Signature · 1 line
Bye, Peter Korsgaard
PATCH 1/1 configs/zynq_zybo: remove defconfig
In reply to Thomas PetazzoniQuoted 6 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Thomas" == Thomas Petazzoni <[email protected]> writes:
This defconfig was added in October 2016 and was never updated since then. It currently fails to build because U-Boot is too old and doesn't build with host-openssl in version 1.1.x.
Quoted 8 lines
On February 13, 2019, the original submitter was notified, but didn't reply, so let's remove the defconfig for this platform.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/165766194
Signed-off-by Thomas Petazzoni <[email protected]>
Committed, thanks.
Signature · 1 line
Bye, Peter Korsgaard