arm64: dts: ls1028a: Add Audio DT nodes
Subsystems (2)
PATCH v2 1/1 arm64: dts: ls1028a: Add Audio DT nodes
This patch adds Audio DT nodes for LS1028ARDB and LS1028AQDS boards.
---
Changes in v2:
- Modify some nodes' names.
- Use GIC_SPI and IRQ_TYPE_LEVEL_HIGH.
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 62 ++++++++++++++++++++ arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 63 +++++++++++++++++++++ arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 57 +++++++++++++++++++ 3 files changed, 182 insertions(+), 0 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts +62 -0
@@ -32,6 +32,49 @@ device_type = "memory"; reg = <0x0 0x80000000 0x1 0x00000000>; }; + + sys_mclk: clock-mclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "1P8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,format = "i2s"; + simple-audio-card,widgets = + "Microphone", "Microphone Jack", + "Headphone", "Headphone Jack", + "Speaker", "Speaker Ext", + "Line", "Line In Jack"; + simple-audio-card,routing = + "MIC_IN", "Microphone Jack", + "Microphone Jack", "Mic Bias", + "LINE_IN", "Line In Jack", + "Headphone Jack", "HP_OUT", + "Speaker Ext", "LINE_OUT"; + + simple-audio-card,cpu { + sound-dai = <&sai1>; + frame-master; + bitclock-master; + }; + + simple-audio-card,codec { + sound-dai = <&sgtl5000>; + frame-master; + bitclock-master; + system-clock-frequency = <25000000>; + }; + }; }; &duart0 {
@@ -89,5 +132,24 @@ reg = <0x57>; }; }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x5>; + + sgtl5000: audio-codec@a { + #sound-dai-cells = <0>; + compatible = "fsl,sgtl5000"; + reg = <0xa>; + VDDA-supply = <®_1p8v>; + VDDIO-supply = <®_1p8v>; + clocks = <&sys_mclk>; + }; + }; }; }; + +&sai1 { + status = "okay"; +};
arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts +63 -0
78 lines not on this page · raw message
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +57 -0
62 lines not on this page · raw message
Signature · 1 line
1.7.1
Quoted 182 lines · Alison Wang
This patch adds Audio DT nodes for LS1028ARDB and LS1028AQDS boards.
Signed-off-by Alison Wang <[email protected]>---
Changes in v2:
- Modify some nodes' names.
- UseGIC_SPIandIRQ_TYPE_LEVEL_HIGH.arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 62 ++++++++++++++++++++ arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 63 +++++++++++++++++++++ arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 57 +++++++++++++++++++ 3 files changed, 182 insertions(+), 0 deletions(-)arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts +62
-0@@ -32,6 +32,49 @@ device_type = "memory"; reg = <0x0 0x80000000 0x1 0x00000000>; }; + + sys_mclk: clock-mclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "1P8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,format = "i2s"; + simple-audio-card,widgets = + "Microphone", "Microphone Jack", + "Headphone", "Headphone Jack", + "Speaker", "Speaker Ext", + "Line", "Line In Jack"; + simple-audio-card,routing = + "MIC_IN", "Microphone Jack", + "Microphone Jack", "Mic Bias", + "LINE_IN", "Line In Jack", + "Headphone Jack", "HP_OUT", + "Speaker Ext", "LINE_OUT"; + + simple-audio-card,cpu { + sound-dai = <&sai1>; + frame-master; + bitclock-master; + }; + + simple-audio-card,codec { + sound-dai = <&sgtl5000>; + frame-master; + bitclock-master; + system-clock-frequency = <25000000>; + }; + }; }; &duart0 {@@ -89,5 +132,24 @@ reg = <0x57>; }; }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x5>; + + sgtl5000: audio-codec@a { + #sound-dai-cells = <0>; + compatible = "fsl,sgtl5000"; + reg = <0xa>; + VDDA-supply = <®_1p8v>; + VDDIO-supply = <®_1p8v>; + clocks = <&sys_mclk>; + }; + }; }; }; + +&sai1 { + status = "okay"; +};arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts +63
-0@@ -28,6 +28,49 @@ device_type = "memory"; reg = <0x0 0x80000000 0x1 0x0000000>; }; + + sys_mclk: clock-mclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "1P8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,format = "i2s"; + simple-audio-card,widgets = + "Microphone", "Microphone Jack", + "Headphone", "Headphone Jack", + "Speaker", "Speaker Ext", + "Line", "Line In Jack"; + simple-audio-card,routing = + "MIC_IN", "Microphone Jack", + "Microphone Jack", "Mic Bias", + "LINE_IN", "Line In Jack", + "Headphone Jack", "HP_OUT", + "Speaker Ext", "LINE_OUT"; + + simple-audio-card,cpu { + sound-dai = <&sai4>; + frame-master; + bitclock-master; + }; + + simple-audio-card,codec { + sound-dai = <&sgtl5000>; + frame-master; + bitclock-master; + system-clock-frequency = <25000000>; + }; + }; }; &i2c0 {@@ -39,6 +82,22 @@ #address-cells = <1>; #size-cells = <0>; + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1>; + + sgtl5000: audio-codec@a { + #sound-dai-cells = <0>; + compatible = "fsl,sgtl5000"; + reg = <0xa>; + VDDA-supply = <®_1p8v>; + VDDIO-supply = <®_1p8v>; + clocks = <&sys_mclk>; + sclk-strength = <3>; + }; + }; + i2c@2 { #address-cells = <1>; #size-cells = <0>;@@ -71,3 +130,7 @@ &duart1 { status = "okay"; }; + +&sai4 { + status = "okay"; +};arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +0
-0
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi line 339
Quoted 5 lines
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +2
-0@@ -335,5 +335,62 @@ <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; }; + + edma0: dma-controller@22c0000 {
Please sort the node in unit-address.
Shawn
Quoted 60 lines
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +55
-0+ #dma-cells = <2>; + compatible = "fsl,vf610-edma"; + reg = <0x0 0x22c0000 0x0 0x10000>, + <0x0 0x22d0000 0x0 0x10000>, + <0x0 0x22e0000 0x0 0x10000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "edma-tx", "edma-err"; + dma-channels = <32>; + clock-names = "dmamux0", "dmamux1"; + clocks = <&clockgen 4 1>, + <&clockgen 4 1>; + }; + + sai1: audio-controller@f100000 { + #sound-dai-cells = <0>; + compatible = "fsl,vf610-sai"; + reg = <0x0 0xf100000 0x0 0x10000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 1>, <&clockgen 4 1>, + <&clockgen 4 1>, <&clockgen 4 1>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "tx", "rx"; + dmas = <&edma0 1 4>, + <&edma0 1 3>; + status = "disabled"; + }; + + sai2: audio-controller@f110000 { + #sound-dai-cells = <0>; + compatible = "fsl,vf610-sai"; + reg = <0x0 0xf110000 0x0 0x10000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 1>, <&clockgen 4 1>, + <&clockgen 4 1>, <&clockgen 4 1>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "tx", "rx"; + dmas = <&edma0 1 6>, + <&edma0 1 5>; + status = "disabled"; + }; + + sai4: audio-controller@f130000 { + #sound-dai-cells = <0>; + compatible = "fsl,vf610-sai"; + reg = <0x0 0xf130000 0x0 0x10000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 1>, <&clockgen 4 1>, + <&clockgen 4 1>, <&clockgen 4 1>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "tx", "rx"; + dmas = <&edma0 1 10>, + <&edma0 1 9>; + status = "disabled"; + }; }; };Signature · 1 line
1.7.1
Quoted 25 lines · Alison Wang
Quoted 9 lines
This patch adds Audio DT nodes for LS1028ARDB and LS1028AQDS boards.
Signed-off-by Alison Wang <[email protected]>---
Changes in v2:
- Modify some nodes' names.
- UseGIC_SPIandIRQ_TYPE_LEVEL_HIGH.arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 62++++++++++++++++++++
Quoted 1 line
arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 63+++++++++++++++++++++
Quoted 1 line
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 57+++++++++++++++++++
Review
Quoted 3 lines
3 files changed, 182 insertions(+), 0 deletions(-)<snip>
(quoted diff) +0
-0
b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsiarch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi line 335
Quoted 5 lines
index a8cf92a..de590ec 100644
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +0
-0@@ -335,5 +335,62 @@ <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 207
IRQ_TYPE_LEVEL_HIGH>,
Quoted 8 lines
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi line 336
Quoted 1 line
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +0
-0<GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 209
IRQ_TYPE_LEVEL_HIGH>;arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi line 339
Quoted 3 lines
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +2
-0}; + + edma0: dma-controller@22c0000 {Please sort the node in unit-address.
[Alison] Ok, I will update it in v3. Thanks.
Best Regards,
Alison Wang