arm: dts: imx8mq: Add cpufreq support
Subsystems (3)
v3 cover arm: dts: imx8mq: Add cpufreq support
Changes since v2:
* renamed the regulator
* removed the useless enable-active-high from the regulator
* renamed a53_0_opp_table to a53_opp_table
Abel Vesa (3):
arm64: dts: imx8mq: Add the clocks and the latencies for the A53 cores
arm64: dts: imx8mq: Add the buck vdd_arm regulator
arm64: dts: imx8mq: Add the opp table and cores opp properties
arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 35 ++++++++++++++++++++++++++++ arch/arm64/boot/dts/freescale/imx8mq.dtsi | 31 ++++++++++++++++++++++++ 2 files changed, 66 insertions(+)
Signature · 1 line
2.7.4
PATCH v3 1/3 arm64: dts: imx8mq: Add the clocks and the latencies for the A53 cores
The clocks and their latencies will be used by cpufreq-dt.
--- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/arm64/boot/dts/freescale/imx8mq.dtsi +8 -0
@@ -87,6 +87,8 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x0>; + clock-latency = <61036>; /* two CLK32 periods */ + clocks = <&clk IMX8MQ_CLK_ARM>; enable-method = "psci"; next-level-cache = <&A53_L2>; };
@@ -95,6 +97,8 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x1>; + clock-latency = <61036>; /* two CLK32 periods */ + clocks = <&clk IMX8MQ_CLK_ARM>; enable-method = "psci"; next-level-cache = <&A53_L2>; };
@@ -103,6 +107,8 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x2>; + clock-latency = <61036>; /* two CLK32 periods */ + clocks = <&clk IMX8MQ_CLK_ARM>; enable-method = "psci"; next-level-cache = <&A53_L2>; };
@@ -111,6 +117,8 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x3>; + clock-latency = <61036>; /* two CLK32 periods */ + clocks = <&clk IMX8MQ_CLK_ARM>; enable-method = "psci"; next-level-cache = <&A53_L2>; };
Signature · 1 line
2.7.4
PATCH v3 2/3 arm64: dts: imx8mq: Add the buck vdd_arm regulator
In reply to Abel VesaAccording to the schematics, this is a MP2147 switch converter which is controlled by GPIO1_IO13. When set the gpio is set to high the regulator output is set to 0.9V. When the gpio is set to low the regulator output is set to 1V.
--- arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 35 ++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
arch/arm64/boot/dts/freescale/imx8mq-evk.dts +35 -0
@@ -31,6 +31,34 @@ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; enable-active-high; }; + + buck2_reg: regulator-buck2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_buck2>; + compatible = "regulator-gpio"; + regulator-name = "vdd_arm"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1000000>; + gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; + states = <1000000 0x0 + 900000 0x1>; + }; +}; + +&A53_0 { + cpu-supply = <&buck2_reg>; +}; + +&A53_1 { + cpu-supply = <&buck2_reg>; +}; + +&A53_2 { + cpu-supply = <&buck2_reg>; +}; + +&A53_3 { + cpu-supply = <&buck2_reg>; }; &fec1 {
@@ -203,6 +231,13 @@ }; &iomuxc { + pinctrl_buck2: vddarmgrp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x19 + >; + + }; + pinctrl_fec1: fec1grp { fsl,pins = < MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
Signature · 1 line
2.7.4
PATCH v3 3/3 arm64: dts: imx8mq: Add the opp table and cores opp properties
In reply to Abel VesaAdd the 0.8GHz and 1GHz opps. According to the datasheet:
https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQIEC.pdf
section 3.1.3 Operating ranges.
The 0.8GHz opp runs in nominal mode with the regulator set to 0.9V. The 1GHz runs in overdrive mode with the regulator set to 1V.
--- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)
arch/arm64/boot/dts/freescale/imx8mq.dtsi +23 -0
@@ -91,6 +91,7 @@ clocks = <&clk IMX8MQ_CLK_ARM>; enable-method = "psci"; next-level-cache = <&A53_L2>; + operating-points-v2 = <&a53_opp_table>; }; A53_1: cpu@1 {
@@ -101,6 +102,7 @@ clocks = <&clk IMX8MQ_CLK_ARM>; enable-method = "psci"; next-level-cache = <&A53_L2>; + operating-points-v2 = <&a53_opp_table>; }; A53_2: cpu@2 {
@@ -111,6 +113,7 @@ clocks = <&clk IMX8MQ_CLK_ARM>; enable-method = "psci"; next-level-cache = <&A53_L2>; + operating-points-v2 = <&a53_opp_table>; }; A53_3: cpu@3 {
@@ -121,6 +124,7 @@ clocks = <&clk IMX8MQ_CLK_ARM>; enable-method = "psci"; next-level-cache = <&A53_L2>; + operating-points-v2 = <&a53_opp_table>; }; A53_L2: l2-cache0 {
@@ -666,6 +670,25 @@ status = "disabled"; }; + + a53_opp_table: opp-table { + compatible = "operating-points-v2"; + opp-shared; + + opp-800000000 { + opp-hz = /bits/ 64 <800000000>; + opp-microvolt = <900000>; + clock-latency-ns = <150000>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1000000>; + clock-latency-ns = <150000>; + opp-suspend; + }; + }; + gic: interrupt-controller@38800000 { compatible = "arm,gic-v3"; reg = <0x38800000 0x10000>, /* GIC Dist */
Signature · 1 line
2.7.4
Shawn Guo
AppliedQuoted 9 lines · Abel Vesa
Changes since v2:
* renamed the regulator
* removed the useless enable-active-high from the regulator
* renameda53_0_opp_tabletoa53_opp_tableAbel Vesa (3):
arm64: dts: imx8mq: Add the clocks and the latencies for the A53 cores
arm64: dts: imx8mq: Add the buckvdd_armregulator
arm64: dts: imx8mq: Add the opp table and cores opp properties
Applied all, thanks.