Skip to contentSkip to conversation

4.14.105-stable review

PATCH In review Greg Kroah-Hartman 5 participants 57 messages Mar 4, 2019 – Mar 5, 2019

Subsystems (8)
lore
Share & tools
lore

Greg Kroah-Hartman

author maintainer
#0 lore raw

cover 4.14.105-stable review

This is the start of the stable review cycle for the 4.14.105 release. There are 52 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Wed Mar 6 08:15:55 UTC 2019. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.14.105-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.14.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <[email protected]>

    Linux 4.14.105-rc1

Andy Lutomirski <[email protected]>
x86/uaccess: Don't leak the AC flag into __put_user() value evaluation

Paul Burton <[email protected]>
MIPS: eBPF: Fix icache flush end address

Michael Clark <[email protected]>
MIPS: fix truncation in __cmpxchg_small for short values

Jann Horn <[email protected]>
mm: enforce min addr even if capable() in expand_downwards()

BOUGH CHEN <[email protected]>
mmc: sdhci-esdhc-imx: correct the fix of ERR004536

Takeshi Saito <[email protected]>
mmc: tmio: fix access width of Block Count Register

Sergei Shtylyov <[email protected]>
mmc: tmio_mmc_core: don't claim spurious interrupts

Jonathan Neuschäfer <[email protected]>
mmc: spi: Fix card detection during probe

Seth Forshee <[email protected]>
powerpc: Always initialize input array when calling epapr_hypercall()

Vitaly Kuznetsov <[email protected]>
KVM: nSVM: clear events pending from svm_complete_interrupts() when exiting to L1

Suravee Suthikulpanit <[email protected]>
svm: Fix AVIC incomplete IPI emulation

Chaitanya Tata <[email protected]>
cfg80211: extend range deviation for DMG

Mathieu Malaterre <[email protected]>
mac80211: Add attribute aligned(2) to struct 'action'

Balaji Pothunoori <[email protected]>
mac80211: don't initiate TDLS connection if station is not associated to AP

Thomas Falcon <[email protected]>
ibmveth: Do not process frames after calling napi_reschedule

Maciej Żenczykowski <[email protected]>
net: dev_is_mac_header_xmit() true for ARPHRD_RAWIP

Zhang Run <[email protected]>
net: usb: asix: ax88772_bind return error when hw_reset fail

Haiyang Zhang <[email protected]>
hv_netvsc: Fix ethtool change hash key error

Atsushi Nemoto <[email protected]>
net: altera_tse: fix connect_local_phy error path

Varun Prakash <[email protected]>
scsi: csiostor: fix NULL pointer dereference in csio_vport_set_state()

Tejun Heo <[email protected]>
writeback: synchronize sync(2) against cgroup writeback membership switches

Ernesto A. Fernández <[email protected]>
direct-io: allow direct writes to empty inodes

Liam Mark <[email protected]>
staging: android: ion: Support cpu access during dma_buf_detach

Tomonori Sakita <[email protected]>
serial: fsl_lpuart: fix maximum acceptable baud rate with over-sampling

Kenneth Feng <[email protected]>
drm/amd/powerplay: OD setting fix on Vega10

Xie Yongji <[email protected]>
locking/rwsem: Fix (possible) missed wakeup

Peter Zijlstra <[email protected]>
futex: Fix (possible) missed wakeup

Prateek Sood <[email protected]>
sched/wait: Fix rcuwait_wake_up() ordering

Bob Copeland <[email protected]>
mac80211: fix miscounting of ttl-dropped frames

Nathan Chancellor <[email protected]>
staging: rtl8723bs: Fix build error with Clang when inlining is disabled

Aaron Hill <[email protected]>

    drivers: thermal: int340x_thermal: Fix sysfs race condition

Eugeniy Paltsev <[email protected]>
ARC: fix __ffs return value to avoid build warnings

Geert Uytterhoeven <[email protected]>
selftests: gpio-mockup-chardev: Check asprintf() for error

Fathi Boudra <[email protected]>
selftests: seccomp: use LDLIBS instead of LDFLAGS

Silvio Cesare <[email protected]>
ASoC: imx-audmux: change snprintf to scnprintf for possible overflow

Silvio Cesare <[email protected]>
ASoC: dapm: change snprintf to scnprintf for possible overflow

Srinivas Ramana <[email protected]>
genirq: Make sure the initial affinity is not empty

Dan Carpenter <[email protected]>
usb: gadget: Potential NULL dereference on allocation error

Zeng Tao <[email protected]>
usb: dwc3: gadget: Fix the uninitialized link_state when udc starts

Bo He <[email protected]>
usb: dwc3: gadget: synchronize_irq dwc irq in suspend

Dan Carpenter <[email protected]>

    thermal: int340x_thermal: Fix a NULL vs IS_ERR() check

Marek Vasut <[email protected]>
clk: vc5: Abort clock configuration without upstream clock

Yizhuo <[email protected]>
ASoC: Variable "val" in function rt274_i2c_probe() could be uninitialized

Dan Carpenter <[email protected]>
ALSA: compress: prevent potential divide by zero bugs

Rander Wang <[email protected]>
ASoC: Intel: Haswell/Broadwell: fix setting for .dynamic field

Kristian H. Kristensen <[email protected]>
drm/msm: Unblock writer if reader closes file

John Garry <[email protected]>
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached

Jose Abreu <[email protected]>
net: stmmac: Disable ACS Feature for GMAC >= 4

Florian Fainelli <[email protected]>
net: stmmac: Fix reception of Broadcom switches tags

Greg Kroah-Hartman <[email protected]>
Revert "loop: Fold __loop_release into loop_release"

Greg Kroah-Hartman <[email protected]>
Revert "loop: Get rid of loop_index_mutex"

Greg Kroah-Hartman <[email protected]>
Revert "loop: Fix double mutex_unlock(&loop_ctl_mutex) in loop_control_ioctl()"

-------------

Diffstat:

 Makefile                                           |  4 +-
 arch/arc/include/asm/bitops.h                      |  6 +--
 arch/mips/kernel/cmpxchg.c                         |  3 +-
 arch/mips/net/ebpf_jit.c                           |  2 +-
 arch/powerpc/include/asm/epapr_hcalls.h            | 12 +++---
 arch/x86/include/asm/uaccess.h                     |  7 ++--
 arch/x86/kvm/svm.c                                 | 27 ++++++-------
 drivers/block/loop.c                               | 47 ++++++++++++----------
 drivers/clk/clk-versaclock5.c                      |  4 +-
 .../amd/powerplay/hwmgr/vega10_processpptables.c   | 22 +++++++++-
 drivers/gpu/drm/msm/msm_rd.c                       |  7 +++-
 drivers/mmc/host/mmc_spi.c                         |  1 +
 drivers/mmc/host/renesas_sdhi_sys_dmac.c           |  1 +
 drivers/mmc/host/sdhci-esdhc-imx.c                 |  9 +++--
 drivers/mmc/host/tmio_mmc.h                        |  5 +++
 drivers/mmc/host/tmio_mmc_core.c                   | 17 +++++---
 drivers/net/ethernet/altera/altera_tse_main.c      |  4 +-
 drivers/net/ethernet/ibm/ibmveth.c                 |  2 -
 drivers/net/ethernet/stmicro/stmmac/common.h       |  2 +-
 drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c  |  3 +-
 .../net/ethernet/stmicro/stmmac/dwmac1000_core.c   | 12 +++++-
 .../net/ethernet/stmicro/stmmac/dwmac100_core.c    | 15 ++++++-
 drivers/net/ethernet/stmicro/stmmac/dwmac4.h       |  2 +-
 drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c  |  5 ++-
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c  |  9 ++++-
 drivers/net/hyperv/rndis_filter.c                  | 25 +++++++++---
 drivers/net/usb/asix_devices.c                     |  9 ++++-
 drivers/scsi/csiostor/csio_attr.c                  |  2 +-
 drivers/scsi/libsas/sas_expander.c                 |  2 +
 drivers/staging/android/ion/ion.c                  |  2 +-
 drivers/staging/rtl8723bs/include/ieee80211.h      |  6 +--
 .../int340x_thermal/processor_thermal_device.c     | 30 +++++++-------
 drivers/tty/serial/fsl_lpuart.c                    |  2 +-
 drivers/usb/dwc3/gadget.c                          |  3 ++
 drivers/usb/gadget/function/f_sourcesink.c         |  2 +-
 fs/direct-io.c                                     |  5 ++-
 fs/fs-writeback.c                                  | 40 +++++++++++++++++-
 include/linux/backing-dev-defs.h                   |  1 +
 include/linux/if_arp.h                             |  1 +
 kernel/exit.c                                      |  2 +-
 kernel/futex.c                                     | 13 +++---
 kernel/irq/manage.c                                |  3 ++
 kernel/locking/rwsem-xadd.c                        | 11 ++++-
 mm/backing-dev.c                                   |  1 +
 mm/mmap.c                                          |  7 ++--
 net/mac80211/cfg.c                                 |  4 ++
 net/mac80211/rx.c                                  |  6 ++-
 net/wireless/reg.c                                 |  4 +-
 sound/core/compress_offload.c                      |  3 +-
 sound/soc/codecs/rt274.c                           |  5 ++-
 sound/soc/fsl/imx-audmux.c                         | 24 +++++------
 sound/soc/intel/boards/broadwell.c                 |  2 +-
 sound/soc/intel/boards/haswell.c                   |  2 +-
 sound/soc/soc-dapm.c                               | 10 ++---
 tools/testing/selftests/gpio/gpio-mockup-chardev.c |  9 +++--
 tools/testing/selftests/seccomp/Makefile           |  2 +-
 56 files changed, 314 insertions(+), 152 deletions(-)
author maintainer
#1 lore raw

PATCH 1/52 Revert "loop: Fix double mutex_unlock(&loop_ctl_mutex) in loop_control_ioctl()"

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Greg Kroah-Hartman <[email protected]>

This reverts commit d2762edcb6af99fc9322bab0b1d4e71a427760e8 which is commit 628bd85947091830a8c4872adfd5ed1d515a9cf2 upstream.

It does not work properly in the 4.14.y tree and causes more problems than it fixes, so revert it.

---
 drivers/block/loop.c |    2 ++
 1 file changed, 2 insertions(+)
drivers/block/loop.c +2 -0
@@ -1996,10 +1996,12 @@ static long loop_control_ioctl(struct fi
 			break;
 		if (lo->lo_state != Lo_unbound) {
 			ret = -EBUSY;
+			mutex_unlock(&loop_ctl_mutex);
 			break;
 		}
 		if (atomic_read(&lo->lo_refcnt) > 0) {
 			ret = -EBUSY;
+			mutex_unlock(&loop_ctl_mutex);
 			break;
 		}
 		lo->lo_disk->private_data = NULL;
author maintainer
#2 lore raw

PATCH 2/52 Revert "loop: Get rid of loop_index_mutex"

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Greg Kroah-Hartman <[email protected]>

This reverts commit c1e63df4f30c3918476ac9bc594355b0e9629893 which is commit 0a42e99b58a208839626465af194cfe640ef9493 upstream.

It does not work properly in the 4.14.y tree and causes more problems than it fixes, so revert it.

---
 drivers/block/loop.c |   39 +++++++++++++++++++--------------------
 1 file changed, 19 insertions(+), 20 deletions(-)
drivers/block/loop.c +19 -20
@@ -81,6 +81,7 @@
 #include <linux/uaccess.h>
 
 static DEFINE_IDR(loop_index_idr);
+static DEFINE_MUTEX(loop_index_mutex);
 static DEFINE_MUTEX(loop_ctl_mutex);
 
 static int max_part;
@@ -1618,11 +1619,9 @@ static int lo_compat_ioctl(struct block_
 static int lo_open(struct block_device *bdev, fmode_t mode)
 {
 	struct loop_device *lo;
-	int err;
+	int err = 0;
 
-	err = mutex_lock_killable(&loop_ctl_mutex);
-	if (err)
-		return err;
+	mutex_lock(&loop_index_mutex);
 	lo = bdev->bd_disk->private_data;
 	if (!lo) {
 		err = -ENXIO;
@@ -1631,7 +1630,7 @@ static int lo_open(struct block_device *
 
 	atomic_inc(&lo->lo_refcnt);
 out:
-	mutex_unlock(&loop_ctl_mutex);
+	mutex_unlock(&loop_index_mutex);
 	return err;
 }
 
@@ -1640,11 +1639,12 @@ static void lo_release(struct gendisk *d
 	struct loop_device *lo;
 	int err;
 
-	mutex_lock(&loop_ctl_mutex);
+	mutex_lock(&loop_index_mutex);
 	lo = disk->private_data;
 	if (atomic_dec_return(&lo->lo_refcnt))
-		goto out_unlock;
+		goto unlock_index;
 
+	mutex_lock(&loop_ctl_mutex);
 	if (lo->lo_flags & LO_FLAGS_AUTOCLEAR) {
 		/*
 		 * In autoclear mode, stop the loop thread
@@ -1652,7 +1652,7 @@ static void lo_release(struct gendisk *d
 		 */
 		err = loop_clr_fd(lo);
 		if (!err)
-			return;
+			goto unlock_index;
 	} else if (lo->lo_state == Lo_bound) {
 		/*
 		 * Otherwise keep thread (if running) and config,
@@ -1662,8 +1662,9 @@ static void lo_release(struct gendisk *d
 		blk_mq_unfreeze_queue(lo->lo_queue);
 	}
 
-out_unlock:
 	mutex_unlock(&loop_ctl_mutex);
+unlock_index:
+	mutex_unlock(&loop_index_mutex);
 }
 
 static const struct block_device_operations lo_fops = {
@@ -1956,7 +1957,7 @@ static struct kobject *loop_probe(dev_t
 	struct kobject *kobj;
 	int err;
 
-	mutex_lock(&loop_ctl_mutex);
+	mutex_lock(&loop_index_mutex);
 	err = loop_lookup(&lo, MINOR(dev) >> part_shift);
 	if (err < 0)
 		err = loop_add(&lo, MINOR(dev) >> part_shift);
@@ -1964,7 +1965,7 @@ static struct kobject *loop_probe(dev_t
 		kobj = NULL;
 	else
 		kobj = get_disk(lo->lo_disk);
-	mutex_unlock(&loop_ctl_mutex);
+	mutex_unlock(&loop_index_mutex);
 
 	*part = 0;
 	return kobj;
@@ -1974,13 +1975,9 @@ static long loop_control_ioctl(struct fi
 			       unsigned long parm)
 {
 	struct loop_device *lo;
-	int ret;
-
-	ret = mutex_lock_killable(&loop_ctl_mutex);
-	if (ret)
-		return ret;
+	int ret = -ENOSYS;
 
-	ret = -ENOSYS;
+	mutex_lock(&loop_index_mutex);
 	switch (cmd) {
 	case LOOP_CTL_ADD:
 		ret = loop_lookup(&lo, parm);
@@ -1994,6 +1991,7 @@ static long loop_control_ioctl(struct fi
 		ret = loop_lookup(&lo, parm);
 		if (ret < 0)
 			break;
+		mutex_lock(&loop_ctl_mutex);
 		if (lo->lo_state != Lo_unbound) {
 			ret = -EBUSY;
 			mutex_unlock(&loop_ctl_mutex);
@@ -2005,6 +2003,7 @@ static long loop_control_ioctl(struct fi
 			break;
 		}
 		lo->lo_disk->private_data = NULL;
+		mutex_unlock(&loop_ctl_mutex);
 		idr_remove(&loop_index_idr, lo->lo_number);
 		loop_remove(lo);
 		break;
@@ -2014,7 +2013,7 @@ static long loop_control_ioctl(struct fi
 			break;
 		ret = loop_add(&lo, -1);
 	}
-	mutex_unlock(&loop_ctl_mutex);
+	mutex_unlock(&loop_index_mutex);
 
 	return ret;
 }
@@ -2098,10 +2097,10 @@ static int __init loop_init(void)
 				  THIS_MODULE, loop_probe, NULL, NULL);
 
 	/* pre-create number of devices given by config or max_loop */
-	mutex_lock(&loop_ctl_mutex);
+	mutex_lock(&loop_index_mutex);
 	for (i = 0; i < nr; i++)
 		loop_add(&lo, i);
-	mutex_unlock(&loop_ctl_mutex);
+	mutex_unlock(&loop_index_mutex);
 
 	printk(KERN_INFO "loop: module loaded\n");
 	return 0;
author maintainer
#3 lore raw

PATCH 3/52 Revert "loop: Fold __loop_release into loop_release"

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Greg Kroah-Hartman <[email protected]>

This reverts commit f1e81ba8a3fa56dcc48828869b392b29559a0ac3 which is commit 967d1dc144b50ad005e5eecdfadfbcfb399ffff6 upstream.

It does not work properly in the 4.14.y tree and causes more problems than it fixes, so revert it.

---
 drivers/block/loop.c |   16 +++++++++-------
 1 file changed, 9 insertions(+), 7 deletions(-)
drivers/block/loop.c +9 -7
@@ -1634,15 +1634,12 @@ out:
 	return err;
 }
 
-static void lo_release(struct gendisk *disk, fmode_t mode)
+static void __lo_release(struct loop_device *lo)
 {
-	struct loop_device *lo;
 	int err;
 
-	mutex_lock(&loop_index_mutex);
-	lo = disk->private_data;
 	if (atomic_dec_return(&lo->lo_refcnt))
-		goto unlock_index;
+		return;
 
 	mutex_lock(&loop_ctl_mutex);
 	if (lo->lo_flags & LO_FLAGS_AUTOCLEAR) {
@@ -1652,7 +1649,7 @@ static void lo_release(struct gendisk *d
 		 */
 		err = loop_clr_fd(lo);
 		if (!err)
-			goto unlock_index;
+			return;
 	} else if (lo->lo_state == Lo_bound) {
 		/*
 		 * Otherwise keep thread (if running) and config,
@@ -1663,7 +1660,12 @@ static void lo_release(struct gendisk *d
 	}
 
 	mutex_unlock(&loop_ctl_mutex);
-unlock_index:
+}
+
+static void lo_release(struct gendisk *disk, fmode_t mode)
+{
+	mutex_lock(&loop_index_mutex);
+	__lo_release(disk->private_data);
 	mutex_unlock(&loop_index_mutex);
 }
 
author maintainer
#4 lore raw

PATCH 4/52 net: stmmac: Fix reception of Broadcom switches tags

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Florian Fainelli <[email protected]>

commit 8cad443eacf661796a740903a75cb8944c675b4e upstream.

Broadcom tags inserted by Broadcom switches put a 4 byte header after the MAC SA and before the EtherType, which may look like some sort of 0 length LLC/SNAP packet (tcpdump and wireshark do think that way). With ACS enabled in stmmac the packets were truncated to 8 bytes on reception, whereas clearing this bit allowed normal reception to occur.

In order to make that possible, we need to pass a net_device argument to the different core_init() functions and we are dependent on the Broadcom tagger padding packets correctly (which it now does). To be as little invasive as possible, this is only done for gmac1000 when the network device is DSA-enabled (netdev_uses_dsa() returns true).

---
 drivers/net/ethernet/stmicro/stmmac/common.h         |    2 +-
 drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c    |    3 ++-
 drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c |   12 +++++++++++-
 drivers/net/ethernet/stmicro/stmmac/dwmac100_core.c  |   15 +++++++++++++--
 drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c    |   12 +++++++++++-
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c    |    2 +-
 6 files changed, 39 insertions(+), 7 deletions(-)
drivers/net/ethernet/stmicro/stmmac/common.h +1 -1
@@ -475,7 +475,7 @@ struct mac_device_info;
 /* Helpers to program the MAC core */
 struct stmmac_ops {
 	/* MAC core initialization */
-	void (*core_init)(struct mac_device_info *hw, int mtu);
+	void (*core_init)(struct mac_device_info *hw, struct net_device *dev);
 	/* Enable the MAC RX/TX */
 	void (*set_mac)(void __iomem *ioaddr, bool enable);
 	/* Enable and verify that the IPC module is supported */
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +2 -1
@@ -477,7 +477,8 @@ static int sun8i_dwmac_init(struct platf
 	return 0;
 }
 
-static void sun8i_dwmac_core_init(struct mac_device_info *hw, int mtu)
+static void sun8i_dwmac_core_init(struct mac_device_info *hw,
+				  struct net_device *dev)
 {
 	void __iomem *ioaddr = hw->pcsr;
 	u32 v;
drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c +11 -1
@@ -25,18 +25,28 @@
 #include <linux/crc32.h>
 #include <linux/slab.h>
 #include <linux/ethtool.h>
+#include <net/dsa.h>
 #include <asm/io.h>
 #include "stmmac_pcs.h"
 #include "dwmac1000.h"
 
-static void dwmac1000_core_init(struct mac_device_info *hw, int mtu)
+static void dwmac1000_core_init(struct mac_device_info *hw,
+				struct net_device *dev)
 {
 	void __iomem *ioaddr = hw->pcsr;
 	u32 value = readl(ioaddr + GMAC_CONTROL);
+	int mtu = dev->mtu;
 
 	/* Configure GMAC core */
 	value |= GMAC_CORE_INIT;
 
+	/* Clear ACS bit because Ethernet switch tagging formats such as
+	 * Broadcom tags can look like invalid LLC/SNAP packets and cause the
+	 * hardware to truncate packets on reception.
+	 */
+	if (netdev_uses_dsa(dev))
+		value &= ~GMAC_CONTROL_ACS;
+
 	if (mtu > 1500)
 		value |= GMAC_CONTROL_2K;
 	if (mtu > 2000)
drivers/net/ethernet/stmicro/stmmac/dwmac100_core.c +13 -2
@@ -25,15 +25,26 @@
 *******************************************************************************/
 
 #include <linux/crc32.h>
+#include <net/dsa.h>
 #include <asm/io.h>
 #include "dwmac100.h"
 
-static void dwmac100_core_init(struct mac_device_info *hw, int mtu)
+static void dwmac100_core_init(struct mac_device_info *hw,
+			       struct net_device *dev)
 {
 	void __iomem *ioaddr = hw->pcsr;
 	u32 value = readl(ioaddr + MAC_CONTROL);
 
-	writel((value | MAC_CORE_INIT), ioaddr + MAC_CONTROL);
+	value |= MAC_CORE_INIT;
+
+	/* Clear ASTP bit because Ethernet switch tagging formats such as
+	 * Broadcom tags can look like invalid LLC/SNAP packets and cause the
+	 * hardware to truncate packets on reception.
+	 */
+	if (netdev_uses_dsa(dev))
+		value &= ~MAC_CONTROL_ASTP;
+
+	writel(value, ioaddr + MAC_CONTROL);
 
 #ifdef STMMAC_VLAN_TAG_USED
 	writel(ETH_P_8021Q, ioaddr + MAC_VLAN1);
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +11 -1
@@ -17,16 +17,26 @@
 #include <linux/slab.h>
 #include <linux/ethtool.h>
 #include <linux/io.h>
+#include <net/dsa.h>
 #include "stmmac_pcs.h"
 #include "dwmac4.h"
 
-static void dwmac4_core_init(struct mac_device_info *hw, int mtu)
+static void dwmac4_core_init(struct mac_device_info *hw,
+			     struct net_device *dev)
 {
 	void __iomem *ioaddr = hw->pcsr;
 	u32 value = readl(ioaddr + GMAC_CONFIG);
+	int mtu = dev->mtu;
 
 	value |= GMAC_CORE_INIT;
 
+	/* Clear ACS bit because Ethernet switch tagging formats such as
+	 * Broadcom tags can look like invalid LLC/SNAP packets and cause the
+	 * hardware to truncate packets on reception.
+	 */
+	if (netdev_uses_dsa(dev))
+		value &= ~GMAC_CONFIG_ACS;
+
 	if (mtu > 1500)
 		value |= GMAC_CONFIG_2K;
 	if (mtu > 2000)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1 -1
@@ -2497,7 +2497,7 @@ static int stmmac_hw_setup(struct net_de
 	}
 
 	/* Initialize the MAC Core */
-	priv->hw->mac->core_init(priv->hw, dev->mtu);
+	priv->hw->mac->core_init(priv->hw, dev);
 
 	/* Initialize MTL*/
 	if (priv->synopsys_id >= DWMAC_CORE_4_00)
author maintainer
#5 lore raw

PATCH 5/52 net: stmmac: Disable ACS Feature for GMAC >= 4

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jose Abreu <[email protected]>

commit 565020aaeebfa7c8b3ec077bee38f4c15acc9905 upstream.

ACS Feature is currently enabled for GMAC >= 4 but the llc_snap status is never checked in descriptor rx_status callback. This will cause stmmac to always strip packets even that ACS feature is already stripping them.

Lets be safe and disable the ACS feature for GMAC >= 4 and always strip the packets for this GMAC version.

Fixes 477286b53f55 ("stmmac: add GMAC4 core support")
Cc David S. Miller <[email protected]>
Cc Joao Pinto <[email protected]>
Cc Giuseppe Cavallaro <[email protected]>
Cc Alexandre Torgue <[email protected]>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac4.h      |    2 +-
 drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c |    7 -------
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c |    7 ++++++-
 3 files changed, 7 insertions(+), 9 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac4.h +1 -1
@@ -336,7 +336,7 @@ enum power_event {
 #define MTL_RX_OVERFLOW_INT		BIT(16)
 
 /* Default operating mode of the MAC */
-#define GMAC_CORE_INIT (GMAC_CONFIG_JD | GMAC_CONFIG_PS | GMAC_CONFIG_ACS | \
+#define GMAC_CORE_INIT (GMAC_CONFIG_JD | GMAC_CONFIG_PS | \
 			GMAC_CONFIG_BE | GMAC_CONFIG_DCRS)
 
 /* To dump the core regs excluding  the Address Registers */
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +0 -7
@@ -30,13 +30,6 @@ static void dwmac4_core_init(struct mac_
 
 	value |= GMAC_CORE_INIT;
 
-	/* Clear ACS bit because Ethernet switch tagging formats such as
-	 * Broadcom tags can look like invalid LLC/SNAP packets and cause the
-	 * hardware to truncate packets on reception.
-	 */
-	if (netdev_uses_dsa(dev))
-		value &= ~GMAC_CONFIG_ACS;
-
 	if (mtu > 1500)
 		value |= GMAC_CONFIG_2K;
 	if (mtu > 2000)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +6 -1
@@ -3415,8 +3415,13 @@ static int stmmac_rx(struct stmmac_priv
 
 			/* ACS is set; GMAC core strips PAD/FCS for IEEE 802.3
 			 * Type frames (LLC/LLC-SNAP)
+			 *
+			 * llc_snap is never checked in GMAC >= 4, so this ACS
+			 * feature is always disabled and packets need to be
+			 * stripped manually.
 			 */
-			if (unlikely(status != llc_snap))
+			if (unlikely(priv->synopsys_id >= DWMAC_CORE_4_00) ||
+			    unlikely(status != llc_snap))
 				frame_len -= ETH_FCS_LEN;
 
 			if (netif_msg_rx_status(priv)) {
author maintainer
#6 lore raw

PATCH 6/52 scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: John Garry <[email protected]>

commit ffeafdd2bf0b280d67ec1a47ea6287910d271f3f upstream.

The sysfs phy_identifier attribute for a sas_end_device comes from the rphy phy_identifier value.

Currently this is not being set for rphys with an end device attached, so we see incorrect symlinks from systemd disk/by-path:

root@localhost:~# ls -l /dev/disk/by-path/
total 0
lrwxrwxrwx 1 root root  9 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0 -> ../../sdb
lrwxrwxrwx 1 root root 10 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0-part1 -> ../../sdb1
lrwxrwxrwx 1 root root 10 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0-part2 -> ../../sdb2
lrwxrwxrwx 1 root root 10 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0-part3 -> ../../sdc3

Indeed, each sas_end_device phy_identifier value is 0:

root@localhost:/# more sys/class/sas_device/end_device-0\:0\:2/phy_identifier
0
root@localhost:/# more sys/class/sas_device/end_device-0\:0\:10/phy_identifier
0

This patch fixes the discovery code to set the phy_identifier. With this, we now get proper symlinks:

root@localhost:~# ls -l /dev/disk/by-path/
total 0
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy10-lun-0 -> ../../sdg
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy11-lun-0 -> ../../sdh
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy2-lun-0 -> ../../sda
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy2-lun-0-part1 -> ../../sda1
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy3-lun-0 -> ../../sdb
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy3-lun-0-part1 -> ../../sdb1
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy3-lun-0-part2 -> ../../sdb2
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0 -> ../../sdc
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0-part1 -> ../../sdc1
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0-part2 -> ../../sdc2
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0-part3 -> ../../sdc3
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy5-lun-0 -> ../../sdd
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0 -> ../../sde
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0-part1 -> ../../sde1
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0-part2 -> ../../sde2
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0-part3 -> ../../sde3
lrwxrwxrwx 1 root root  9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0 -> ../../sdf
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0-part1 -> ../../sdf1
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0-part2 -> ../../sdf2
lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0-part3 -> ../../sdf3
---
 drivers/scsi/libsas/sas_expander.c |    2 ++
 1 file changed, 2 insertions(+)
drivers/scsi/libsas/sas_expander.c +2 -0
@@ -829,6 +829,7 @@ static struct domain_device *sas_ex_disc
 		rphy = sas_end_device_alloc(phy->port);
 		if (!rphy)
 			goto out_free;
+		rphy->identify.phy_identifier = phy_id;
 
 		child->rphy = rphy;
 		get_device(&rphy->dev);
@@ -856,6 +857,7 @@ static struct domain_device *sas_ex_disc
 
 		child->rphy = rphy;
 		get_device(&rphy->dev);
+		rphy->identify.phy_identifier = phy_id;
 		sas_fill_in_rphy(child, rphy);
 
 		list_add_tail(&child->disco_list_node, &parent->port->disco_list);
author maintainer
#7 lore raw

PATCH 7/52 drm/msm: Unblock writer if reader closes file

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 99c66bc051e7407fe0bf0607b142ec0be1a1d1dd ]

Prevents deadlock when fifo is full and reader closes file.

---
 drivers/gpu/drm/msm/msm_rd.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
drivers/gpu/drm/msm/msm_rd.c +6 -1
index ec56794ad0399..bdce1c9434c6c 100644
@@ -109,7 +109,9 @@ static void rd_write(struct msm_rd_state *rd, const void *buf, int sz)
 		char *fptr = &fifo->buf[fifo->head];
 		int n;
 
-		wait_event(rd->fifo_event, circ_space(&rd->fifo) > 0);
+		wait_event(rd->fifo_event, circ_space(&rd->fifo) > 0 || !rd->open);
+		if (!rd->open)
+			return;
 
 		/* Note that smp_load_acquire() is not strictly required
 		 * as CIRC_SPACE_TO_END() does not access the tail more
@@ -207,7 +209,10 @@ static int rd_open(struct inode *inode, struct file *file)
 static int rd_release(struct inode *inode, struct file *file)
 {
 	struct msm_rd_state *rd = inode->i_private;
+
 	rd->open = false;
+	wake_up_all(&rd->fifo_event);
+
 	return 0;
 }
 
Signature · 1 line
2.19.1
author maintainer
#8 lore raw

PATCH 8/52 ASoC: Intel: Haswell/Broadwell: fix setting for .dynamic field

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 906a9abc5de73c383af518f5a806f4be2993a0c7 ]

For some reason this field was set to zero when all other drivers use .dynamic = 1 for front-ends. This change was tested on Dell XPS13 and has no impact with the existing legacy driver. The SOF driver also works with this change which enables it to override the fixed topology.

---
 sound/soc/intel/boards/broadwell.c | 2 +-
 sound/soc/intel/boards/haswell.c   | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
sound/soc/intel/boards/broadwell.c +1 -1
index 6dcbbcefc25b4..88c26ab7b0273 100644
@@ -191,7 +191,7 @@ static struct snd_soc_dai_link broadwell_rt286_dais[] = {
 		.stream_name = "Loopback",
 		.cpu_dai_name = "Loopback Pin",
 		.platform_name = "haswell-pcm-audio",
-		.dynamic = 0,
+		.dynamic = 1,
 		.codec_name = "snd-soc-dummy",
 		.codec_dai_name = "snd-soc-dummy-dai",
 		.trigger = {SND_SOC_DPCM_TRIGGER_POST, SND_SOC_DPCM_TRIGGER_POST},
sound/soc/intel/boards/haswell.c +1 -1
index 5e1ea0371c909..8158409921e02 100644
@@ -145,7 +145,7 @@ static struct snd_soc_dai_link haswell_rt5640_dais[] = {
 		.stream_name = "Loopback",
 		.cpu_dai_name = "Loopback Pin",
 		.platform_name = "haswell-pcm-audio",
-		.dynamic = 0,
+		.dynamic = 1,
 		.codec_name = "snd-soc-dummy",
 		.codec_dai_name = "snd-soc-dummy-dai",
 		.trigger = {SND_SOC_DPCM_TRIGGER_POST, SND_SOC_DPCM_TRIGGER_POST},
Signature · 1 line
2.19.1
author maintainer
#9 lore raw

PATCH 9/52 ALSA: compress: prevent potential divide by zero bugs

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 678e2b44c8e3fec3afc7202f1996a4500a50be93 ]

The problem is seen in the q6asm_dai_compr_set_params() function:

	ret = q6asm_map_memory_regions(dir, prtd->audio_client, prtd->phys,
				       (prtd->pcm_size / prtd->periods),
                                        ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
				       prtd->periods);

In this code prtd->pcm_size is the buffer_size and prtd->periods comes from params->buffer.fragments. If we allow the number of fragments to be zero then it results in a divide by zero bug. One possible fix would be to use prtd->pcm_count directly instead of using the division to re-calculate it. But I decided that it doesn't really make sense to allow zero fragments.

---
 sound/core/compress_offload.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
sound/core/compress_offload.c +2 -1
index 4490a699030b1..555df64d46ffc 100644
@@ -529,7 +529,8 @@ static int snd_compress_check_input(struct snd_compr_params *params)
 {
 	/* first let's check the buffer parameter's */
 	if (params->buffer.fragment_size == 0 ||
-	    params->buffer.fragments > INT_MAX / params->buffer.fragment_size)
+	    params->buffer.fragments > INT_MAX / params->buffer.fragment_size ||
+	    params->buffer.fragments == 0)
 		return -EINVAL;
 
 	/* now codec parameters */
Signature · 1 line
2.19.1
author maintainer
#10 lore raw

PATCH 10/52 ASoC: Variable "val" in function rt274_i2c_probe() could be uninitialized

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 8c3590de0a378c2449fc1aec127cc693632458e4 ]

Inside function rt274_i2c_probe(), if regmap_read() function returns -EINVAL, then local variable "val" leaves uninitialized but used in if statement. This is potentially unsafe.

---
 sound/soc/codecs/rt274.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
sound/soc/codecs/rt274.c +4 -1
index 8f92e5c4dd9d7..cd048df762327 100644
@@ -1128,8 +1128,11 @@ static int rt274_i2c_probe(struct i2c_client *i2c,
 		return ret;
 	}
 
-	regmap_read(rt274->regmap,
+	ret = regmap_read(rt274->regmap,
 		RT274_GET_PARAM(AC_NODE_ROOT, AC_PAR_VENDOR_ID), &val);
+	if (ret)
+		return ret;
+
 	if (val != RT274_VENDOR_ID) {
 		dev_err(&i2c->dev,
 			"Device with ID register %#x is not rt274\n", val);
Signature · 1 line
2.19.1
author maintainer
#11 lore raw

PATCH 11/52 clk: vc5: Abort clock configuration without upstream clock

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 2137a109a5e39c2bdccfffe65230ed3fadbaac0e ]

In case the upstream clock are not set, which can happen in case the VC5 has no valid upstream clock, the $src variable is used uninited by regmap_update_bits(). Check for this condition and return -EINVAL in such case.

Note that in case the VC5 has no valid upstream clock, the VC5 can not operate correctly. That is a hardware property of the VC5. The internal oscilator present in some VC5 models is also considered upstream clock.

Cc Alexey Firago <[email protected]>
Cc Laurent Pinchart <[email protected]>
Cc Stephen Boyd <[email protected]>

[[email protected]: Added comment about probe preventing this from happening in the first place]

---
 drivers/clk/clk-versaclock5.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/clk/clk-versaclock5.c +3 -1
index decffb3826ece..a738af893532f 100644
@@ -262,8 +262,10 @@ static int vc5_mux_set_parent(struct clk_hw *hw, u8 index)
 
 		if (vc5->clk_mux_ins == VC5_MUX_IN_XIN)
 			src = VC5_PRIM_SRC_SHDN_EN_XTAL;
-		if (vc5->clk_mux_ins == VC5_MUX_IN_CLKIN)
+		else if (vc5->clk_mux_ins == VC5_MUX_IN_CLKIN)
 			src = VC5_PRIM_SRC_SHDN_EN_CLKIN;
+		else /* Invalid; should have been caught by vc5_probe() */
+			return -EINVAL;
 	}
 
 	return regmap_update_bits(vc5->regmap, VC5_PRIM_SRC_SHDN, mask, src);
Signature · 1 line
2.19.1
author maintainer
#12 lore raw

PATCH 12/52 thermal: int340x_thermal: Fix a NULL vs IS_ERR() check

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 3fe931b31a4078395c1967f0495dcc9e5ec6b5e3 ]

The intel_soc_dts_iosf_init() function doesn't return NULL, it returns error pointers.

Fixes 4d0dd6c1576b ("Thermal/int340x/processor_thermal: Enable auxiliary DTS for Braswell")
---
 drivers/thermal/int340x_thermal/processor_thermal_device.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/thermal/int340x_thermal/processor_thermal_device.c +1 -1
index f02341f7134d4..c6ab7db8c8e23 100644
@@ -416,7 +416,7 @@ static int  proc_thermal_pci_probe(struct pci_dev *pdev,
 		proc_priv->soc_dts = intel_soc_dts_iosf_init(
 					INTEL_SOC_DTS_INTERRUPT_MSI, 2, 0);
 
-		if (proc_priv->soc_dts && pdev->irq) {
+		if (!IS_ERR(proc_priv->soc_dts) && pdev->irq) {
 			ret = pci_enable_msi(pdev);
 			if (!ret) {
 				ret = request_threaded_irq(pdev->irq, NULL,
Signature · 1 line
2.19.1
author maintainer
#13 lore raw

PATCH 13/52 usb: dwc3: gadget: synchronize_irq dwc irq in suspend

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 01c10880d24291a96a4ab0da773e3c5ce4d12da8 ]

We see dwc3 endpoint stopped by unwanted irq during suspend resume test, which is caused dwc3 ep can't be started with error "No Resource".

Here, add synchronize_irq before suspend to sync the pending IRQ handlers complete.

---
 drivers/usb/dwc3/gadget.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/usb/dwc3/gadget.c +2 -0
index 2f96d2d0addd1..5da078bf5f76a 100644
@@ -3327,6 +3327,8 @@ int dwc3_gadget_suspend(struct dwc3 *dwc)
 	dwc3_disconnect_gadget(dwc);
 	__dwc3_gadget_stop(dwc);
 
+	synchronize_irq(dwc->irq_gadget);
+
 	return 0;
 }
 
Signature · 1 line
2.19.1
author maintainer
#14 lore raw

PATCH 14/52 usb: dwc3: gadget: Fix the uninitialized link_state when udc starts

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 88b1bb1f3b88e0bf20b05d543a53a5b99bd7ceb6 ]

Currently the link_state is uninitialized and the default value is 0(U0) before the first time we start the udc, and after we start the udc then
stop the udc, the link_state will be undefined.
We may have the following warnings if we start the udc again with an undefined link_state:

WARNING: CPU: 0 PID: 327 at drivers/usb/dwc3/gadget.c:294 dwc3_send_gadget_ep_cmd+0x304/0x308
dwc3 100e0000.hidwc3_0: wakeup failed --> -22
[...]
Call Trace:
[<c010f270>] (unwind_backtrace) from [<c010b3d8>] (show_stack+0x10/0x14)
[<c010b3d8>] (show_stack) from [<c034a4dc>] (dump_stack+0x84/0x98)
[<c034a4dc>] (dump_stack) from [<c0118000>] (__warn+0xe8/0x100)
[<c0118000>] (__warn) from [<c0118050>](warn_slowpath_fmt+0x38/0x48)
[<c0118050>] (warn_slowpath_fmt) from [<c0442ec0>](dwc3_send_gadget_ep_cmd+0x304/0x308)
[<c0442ec0>] (dwc3_send_gadget_ep_cmd) from [<c0445e68>](dwc3_ep0_start_trans+0x48/0xf4)
[<c0445e68>] (dwc3_ep0_start_trans) from [<c0446750>](dwc3_ep0_out_start+0x64/0x80)
[<c0446750>] (dwc3_ep0_out_start) from [<c04451c0>](__dwc3_gadget_start+0x1e0/0x278)
[<c04451c0>] (__dwc3_gadget_start) from [<c04452e0>](dwc3_gadget_start+0x88/0x10c)
[<c04452e0>] (dwc3_gadget_start) from [<c045ee54>](udc_bind_to_driver+0x88/0xbc)
[<c045ee54>] (udc_bind_to_driver) from [<c045f29c>](usb_gadget_probe_driver+0xf8/0x140)
[<c045f29c>] (usb_gadget_probe_driver) from [<bf005424>](gadget_dev_desc_UDC_store+0xac/0xc4 [libcomposite])
[<bf005424>] (gadget_dev_desc_UDC_store [libcomposite]) from[<c023d8e0>] (configfs_write_file+0xd4/0x160)
[<c023d8e0>] (configfs_write_file) from [<c01d51e8>] (__vfs_write+0x1c/0x114)
[<c01d51e8>] (__vfs_write) from [<c01d5ff4>] (vfs_write+0xa4/0x168)
[<c01d5ff4>] (vfs_write) from [<c01d6d40>] (SyS_write+0x3c/0x90)
[<c01d6d40>] (SyS_write) from [<c0107400>] (ret_fast_syscall+0x0/0x3c)
---
 drivers/usb/dwc3/gadget.c | 1 +
 1 file changed, 1 insertion(+)
drivers/usb/dwc3/gadget.c +1 -0
index 5da078bf5f76a..32dd0d3462da1 100644
@@ -1910,6 +1910,7 @@ static int __dwc3_gadget_start(struct dwc3 *dwc)
 
 	/* begin to receive SETUP packets */
 	dwc->ep0state = EP0_SETUP_PHASE;
+	dwc->link_state = DWC3_LINK_STATE_SS_DIS;
 	dwc3_ep0_out_start(dwc);
 
 	dwc3_gadget_enable_irq(dwc);
Signature · 1 line
2.19.1
author maintainer
#15 lore raw

PATCH 15/52 usb: gadget: Potential NULL dereference on allocation error

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit df28169e1538e4a8bcd8b779b043e5aa6524545c ]

The source_sink_alloc_func() function is supposed to return error pointers on error. The function is called from usb_get_function() which doesn't check for NULL returns so it would result in an Oops.

Of course, in the current kernel, small allocations always succeed so this doesn't affect runtime.

---
 drivers/usb/gadget/function/f_sourcesink.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/usb/gadget/function/f_sourcesink.c +1 -1
index 8784fa12ea2c6..6e9d958004a0d 100644
@@ -842,7 +842,7 @@ static struct usb_function *source_sink_alloc_func(
 
 	ss = kzalloc(sizeof(*ss), GFP_KERNEL);
 	if (!ss)
-		return NULL;
+		return ERR_PTR(-ENOMEM);
 
 	ss_opts =  container_of(fi, struct f_ss_opts, func_inst);
 
Signature · 1 line
2.19.1
author maintainer
#16 lore raw

PATCH 16/52 genirq: Make sure the initial affinity is not empty

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit bddda606ec76550dd63592e32a6e87e7d32583f7 ]

If all CPUs in the irq_default_affinity mask are offline when an interrupt is initialized then irq_setup_affinity() can set an empty affinity mask for a newly allocated interrupt.

Fix this by falling back to cpu_online_mask in case the resulting affinity mask is zero.

---
 kernel/irq/manage.c | 3 +++
 1 file changed, 3 insertions(+)
kernel/irq/manage.c +3 -0
index 4cd85870f00e6..6c877d28838f2 100644
@@ -360,6 +360,9 @@ int irq_setup_affinity(struct irq_desc *desc)
 	}
 
 	cpumask_and(&mask, cpu_online_mask, set);
+	if (cpumask_empty(&mask))
+		cpumask_copy(&mask, cpu_online_mask);
+
 	if (node != NUMA_NO_NODE) {
 		const struct cpumask *nodemask = cpumask_of_node(node);
 
Signature · 1 line
2.19.1
author maintainer
#17 lore raw

PATCH 17/52 ASoC: dapm: change snprintf to scnprintf for possible overflow

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit e581e151e965bf1f2815dd94620b638fec4d0a7e ]

Change snprintf to scnprintf. There are generally two cases where using snprintf causes problems.

1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the buffer size (SIZE) is, then size will end up larger than SIZE. In later uses of snprintf, SIZE - size will result in a negative number, leading to problems. Note that size might already be too large by using size = snprintf before the code reaches a case of size += snprintf.

2) If size is ultimately used as a length parameter for a copy back to user space, then it will potentially allow for a buffer overflow and information disclosure when size is greater than SIZE. When the size is used to index the buffer directly, we can have memory corruption. This also means when size = snprintf... is used, it may also cause problems since size may become large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel configuration.

The solution to these issues is to use scnprintf which returns the number of characters actually written to the buffer, so the size variable will never exceed SIZE.

---
 sound/soc/soc-dapm.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
sound/soc/soc-dapm.c +5 -5
index 53c9d75256393..bba6a917cd02d 100644
@@ -2009,19 +2009,19 @@ static ssize_t dapm_widget_power_read_file(struct file *file,
 		out = is_connected_output_ep(w, NULL, NULL);
 	}
 
-	ret = snprintf(buf, PAGE_SIZE, "%s: %s%s  in %d out %d",
+	ret = scnprintf(buf, PAGE_SIZE, "%s: %s%s  in %d out %d",
 		       w->name, w->power ? "On" : "Off",
 		       w->force ? " (forced)" : "", in, out);
 
 	if (w->reg >= 0)
-		ret += snprintf(buf + ret, PAGE_SIZE - ret,
+		ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 				" - R%d(0x%x) mask 0x%x",
 				w->reg, w->reg, w->mask << w->shift);
 
-	ret += snprintf(buf + ret, PAGE_SIZE - ret, "\n");
+	ret += scnprintf(buf + ret, PAGE_SIZE - ret, "\n");
 
 	if (w->sname)
-		ret += snprintf(buf + ret, PAGE_SIZE - ret, " stream %s %s\n",
+		ret += scnprintf(buf + ret, PAGE_SIZE - ret, " stream %s %s\n",
 				w->sname,
 				w->active ? "active" : "inactive");
 
@@ -2034,7 +2034,7 @@ static ssize_t dapm_widget_power_read_file(struct file *file,
 			if (!p->connect)
 				continue;
 
-			ret += snprintf(buf + ret, PAGE_SIZE - ret,
+			ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 					" %s  \"%s\" \"%s\"\n",
 					(rdir == SND_SOC_DAPM_DIR_IN) ? "in" : "out",
 					p->name ? p->name : "static",
Signature · 1 line
2.19.1
author maintainer
#18 lore raw

PATCH 18/52 ASoC: imx-audmux: change snprintf to scnprintf for possible overflow

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit c407cd008fd039320d147088b52d0fa34ed3ddcb ]

Change snprintf to scnprintf. There are generally two cases where using snprintf causes problems.

1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the buffer size (SIZE) is, then size will end up larger than SIZE. In later uses of snprintf, SIZE - size will result in a negative number, leading to problems. Note that size might already be too large by using size = snprintf before the code reaches a case of size += snprintf.

2) If size is ultimately used as a length parameter for a copy back to user space, then it will potentially allow for a buffer overflow and information disclosure when size is greater than SIZE. When the size is used to index the buffer directly, we can have memory corruption. This also means when size = snprintf... is used, it may also cause problems since size may become large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel configuration.

The solution to these issues is to use scnprintf which returns the number of characters actually written to the buffer, so the size variable will never exceed SIZE.

---
 sound/soc/fsl/imx-audmux.c | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)
sound/soc/fsl/imx-audmux.c +12 -12
index 392d5eef356d3..99e07b01a2ce9 100644
@@ -86,49 +86,49 @@ static ssize_t audmux_read_file(struct file *file, char __user *user_buf,
 	if (!buf)
 		return -ENOMEM;
 
-	ret = snprintf(buf, PAGE_SIZE, "PDCR: %08x\nPTCR: %08x\n",
+	ret = scnprintf(buf, PAGE_SIZE, "PDCR: %08x\nPTCR: %08x\n",
 		       pdcr, ptcr);
 
 	if (ptcr & IMX_AUDMUX_V2_PTCR_TFSDIR)
-		ret += snprintf(buf + ret, PAGE_SIZE - ret,
+		ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 				"TxFS output from %s, ",
 				audmux_port_string((ptcr >> 27) & 0x7));
 	else
-		ret += snprintf(buf + ret, PAGE_SIZE - ret,
+		ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 				"TxFS input, ");
 
 	if (ptcr & IMX_AUDMUX_V2_PTCR_TCLKDIR)
-		ret += snprintf(buf + ret, PAGE_SIZE - ret,
+		ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 				"TxClk output from %s",
 				audmux_port_string((ptcr >> 22) & 0x7));
 	else
-		ret += snprintf(buf + ret, PAGE_SIZE - ret,
+		ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 				"TxClk input");
 
-	ret += snprintf(buf + ret, PAGE_SIZE - ret, "\n");
+	ret += scnprintf(buf + ret, PAGE_SIZE - ret, "\n");
 
 	if (ptcr & IMX_AUDMUX_V2_PTCR_SYN) {
-		ret += snprintf(buf + ret, PAGE_SIZE - ret,
+		ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 				"Port is symmetric");
 	} else {
 		if (ptcr & IMX_AUDMUX_V2_PTCR_RFSDIR)
-			ret += snprintf(buf + ret, PAGE_SIZE - ret,
+			ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 					"RxFS output from %s, ",
 					audmux_port_string((ptcr >> 17) & 0x7));
 		else
-			ret += snprintf(buf + ret, PAGE_SIZE - ret,
+			ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 					"RxFS input, ");
 
 		if (ptcr & IMX_AUDMUX_V2_PTCR_RCLKDIR)
-			ret += snprintf(buf + ret, PAGE_SIZE - ret,
+			ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 					"RxClk output from %s",
 					audmux_port_string((ptcr >> 12) & 0x7));
 		else
-			ret += snprintf(buf + ret, PAGE_SIZE - ret,
+			ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 					"RxClk input");
 	}
 
-	ret += snprintf(buf + ret, PAGE_SIZE - ret,
+	ret += scnprintf(buf + ret, PAGE_SIZE - ret,
 			"\nData received from %s\n",
 			audmux_port_string((pdcr >> 13) & 0x7));
 
Signature · 1 line
2.19.1
author maintainer
#19 lore raw

PATCH 19/52 selftests: seccomp: use LDLIBS instead of LDFLAGS

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 5bbc73a841d7f0bbe025a342146dde462a796a5a ]

seccomp_bpf fails to build due to undefined reference errors:

aarch64-linaro-linux-gcc --sysroot=/build/tmp-rpb-glibc/sysroots/hikey
-O2 -pipe -g -feliminate-unused-debug-types -Wl,-no-as-needed -Wall
-Wl,-O1 -Wl,--hash-style=gnu -Wl,--as-needed -lpthread seccomp_bpf.c -o /build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf /tmp/ccrlR3MW.o: In function `tsync_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1920: undefined reference to sem_post' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1920: undefined reference to sem_post' /tmp/ccrlR3MW.o: In function `TSYNC_setup':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1863: undefined reference to sem_init' /tmp/ccrlR3MW.o: In function TSYNC_teardown':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1904: undefined reference to sem_destroy' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1897: undefined reference to pthread_kill' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1898: undefined reference to pthread_cancel' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1899: undefined reference to pthread_join' /tmp/ccrlR3MW.o: In function `tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /tmp/ccrlR3MW.o: In function `TSYNC_siblings_fail_prctl':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1978: undefined reference to sem_wait' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1990: undefined reference to pthread_join' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1992: undefined reference to pthread_join' /tmp/ccrlR3MW.o: In function tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_with_ancestor':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2016: undefined reference to sem_wait' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2032: undefined reference to pthread_join' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2034: undefined reference to pthread_join' /tmp/ccrlR3MW.o: In function tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /tmp/ccrlR3MW.o: In function `TSYNC_two_sibling_want_nnp':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2046: undefined reference to sem_wait' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2058: undefined reference to pthread_join' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2060: undefined reference to pthread_join' /tmp/ccrlR3MW.o: In function tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_with_no_filter':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2073: undefined reference to sem_wait' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2098: undefined reference to pthread_join' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2100: undefined reference to pthread_join' /tmp/ccrlR3MW.o: In function tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_with_one_divergence':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2125: undefined reference to sem_wait' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2143: undefined reference to pthread_join' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2145: undefined reference to pthread_join' /tmp/ccrlR3MW.o: In function tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to pthread_create' /tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_not_under_filter':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2169: undefined reference to sem_wait' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2202: undefined reference to pthread_join' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2227: undefined reference to pthread_join' /tmp/ccrlR3MW.o: In function tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'

It's GNU Make and linker specific.

The default Makefile rule looks like:

$(CC) $(CFLAGS) $(LDFLAGS) $@ $^ $(LDLIBS)

When linking is done by gcc itself, no issue, but when it needs to be passed to proper ld, only LDLIBS follows and then ld cannot know what libs to link with.

More detail:
https://www.gnu.org/software/make/manual/html_node/Implicit-Variables.html

LDFLAGS
Extra flags to give to compilers when they are supposed to invoke the linker, ‘ld’, such as -L. Libraries (-lfoo) should be added to the LDLIBS variable instead.

LDLIBS
Library flags or names given to compilers when they are supposed to invoke the linker, ‘ld’. LOADLIBES is a deprecated (but still supported) alternative to LDLIBS. Non-library linker flags, such as -L, should go in the LDFLAGS variable.

https://lkml.org/lkml/2010/2/10/362

tools/perf: libraries must come after objects

Link order matters, use LDLIBS instead of LDFLAGS to properly link against libpthread.

---
 tools/testing/selftests/seccomp/Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/testing/selftests/seccomp/Makefile +1 -1
index fce7f4ce06925..1760b3e397306 100644
@@ -9,7 +9,7 @@ BINARIES := seccomp_bpf seccomp_benchmark
 CFLAGS += -Wl,-no-as-needed -Wall
 
 seccomp_bpf: seccomp_bpf.c ../kselftest_harness.h
-	$(CC) $(CFLAGS) $(LDFLAGS) -lpthread $< -o $@
+	$(CC) $(CFLAGS) $(LDFLAGS) $< -lpthread -o $@
 
 TEST_PROGS += $(BINARIES)
 EXTRA_CLEAN := $(BINARIES)
Signature · 1 line
2.19.1
author maintainer
#20 lore raw

PATCH 20/52 selftests: gpio-mockup-chardev: Check asprintf() for error

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 508cacd7da6659ae7b7bdd0a335f675422277758 ]

With gcc 7.3.0:

gpio-mockup-chardev.c: In function ‘get_debugfs’:
gpio-mockup-chardev.c:62:3: warning: ignoring return value of ‘asprintf’, declared with attribute warn_unused_result [-Wunused-result]
asprintf(path, "%s/gpio", mnt_fs_get_target(fs));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Handle asprintf() failures to fix this.

---
 tools/testing/selftests/gpio/gpio-mockup-chardev.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
tools/testing/selftests/gpio/gpio-mockup-chardev.c +6 -3
index 667e916fa7cc1..6ceeeed4eeb98 100644
@@ -37,7 +37,7 @@ static int get_debugfs(char **path)
 	struct libmnt_table *tb;
 	struct libmnt_iter *itr = NULL;
 	struct libmnt_fs *fs;
-	int found = 0;
+	int found = 0, ret;
 
 	cxt = mnt_new_context();
 	if (!cxt)
@@ -58,8 +58,11 @@ static int get_debugfs(char **path)
 			break;
 		}
 	}
-	if (found)
-		asprintf(path, "%s/gpio", mnt_fs_get_target(fs));
+	if (found) {
+		ret = asprintf(path, "%s/gpio", mnt_fs_get_target(fs));
+		if (ret < 0)
+			err(EXIT_FAILURE, "failed to format string");
+	}
 
 	mnt_free_iter(itr);
 	mnt_free_context(cxt);
Signature · 1 line
2.19.1
author maintainer
#21 lore raw

PATCH 21/52 ARC: fix __ffs return value to avoid build warnings

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 4e868f8419cb4cb558c5d428e7ab5629cef864c7 ]

|  CC      mm/nobootmem.o
|In file included from ./include/asm-generic/bug.h:18:0,
|                 from ./arch/arc/include/asm/bug.h:32,
|                 from ./include/linux/bug.h:5,
|                 from ./include/linux/mmdebug.h:5,
|                 from ./include/linux/gfp.h:5,
|                 from ./include/linux/slab.h:15,
|                 from mm/nobootmem.c:14:
|mm/nobootmem.c: In function '__free_pages_memory':
|./include/linux/kernel.h:845:29: warning: comparison of distinct pointer types lacks a cast
|   (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
|                             ^
|./include/linux/kernel.h:859:4: note: in expansion of macro '__typecheck'
|   (__typecheck(x, y) && __no_side_effects(x, y))
|    ^~~~~~~~~~~
|./include/linux/kernel.h:869:24: note: in expansion of macro '__safe_cmp'
|  __builtin_choose_expr(__safe_cmp(x, y), \
|                        ^~~~~~~~~~
|./include/linux/kernel.h:878:19: note: in expansion of macro '__careful_cmp'
| #define min(x, y) __careful_cmp(x, y, <)
|                   ^~~~~~~~~~~~~
|mm/nobootmem.c:104:11: note: in expansion of macro 'min'
|   order = min(MAX_ORDER - 1UL, __ffs(start));

Change __ffs return value from 'int' to 'unsigned long' as it is done in other implementations (like asm-generic, x86, etc...) to avoid build-time warnings in places where type is strictly checked.

As __ffs may return values in [0-31] interval changing return type to unsigned is valid.

---
 arch/arc/include/asm/bitops.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
arch/arc/include/asm/bitops.h +3 -3
index 8da87feec59aa..99e6d8948f4ac 100644
@@ -340,7 +340,7 @@ static inline __attribute__ ((const)) int __fls(unsigned long x)
 /*
  * __ffs: Similar to ffs, but zero based (0-31)
  */
-static inline __attribute__ ((const)) int __ffs(unsigned long word)
+static inline __attribute__ ((const)) unsigned long __ffs(unsigned long word)
 {
 	if (!word)
 		return word;
@@ -400,9 +400,9 @@ static inline __attribute__ ((const)) int ffs(unsigned long x)
 /*
  * __ffs: Similar to ffs, but zero based (0-31)
  */
-static inline __attribute__ ((const)) int __ffs(unsigned long x)
+static inline __attribute__ ((const)) unsigned long __ffs(unsigned long x)
 {
-	int n;
+	unsigned long n;
 
 	asm volatile(
 	"	ffs.f	%0, %1		\n"  /* 0:31; 31(Z) if src 0 */
Signature · 1 line
2.19.1
author maintainer
#22 lore raw

PATCH 22/52 drivers: thermal: int340x_thermal: Fix sysfs race condition

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 129699bb8c7572106b5bbb2407c2daee4727ccad ]

Changes since V1:
* Use dev_info instead of printk
* Use dev_warn instead of BUG_ON

Previously, sysfs_create_group was called before all initialization had fully run - specifically, before pci_set_drvdata was called. Since the sysctl group is visible to userspace as soon as sysfs_create_group returns, a small window of time existed during which a process could read from an uninitialized/partially-initialized device.

This commit moves the creation of the sysctl group to after all initialized is completed. This ensures that it's impossible for userspace to read from a sysctl file before initialization has fully completed.

To catch any future regressions, I've added a check to ensure that proc_thermal_emum_mode is never PROC_THERMAL_NONE when a process tries to read from a sysctl file. Previously, the aforementioned race condition could result in the 'else' branch
running while PROC_THERMAL_NONE was set,
leading to a null pointer deference.

---
 .../processor_thermal_device.c                | 28 ++++++++++---------
 1 file changed, 15 insertions(+), 13 deletions(-)
drivers/thermal/int340x_thermal/processor_thermal_device.c +15 -13
index c6ab7db8c8e23..c344a3783625a 100644
@@ -77,7 +77,12 @@ static ssize_t power_limit_##index##_##suffix##_show(struct device *dev, \
 	struct pci_dev *pci_dev; \
 	struct platform_device *pdev; \
 	struct proc_thermal_device *proc_dev; \
-\
+	\
+	if (proc_thermal_emum_mode == PROC_THERMAL_NONE) { \
+		dev_warn(dev, "Attempted to get power limit before device was initialized!\n"); \
+		return 0; \
+	} \
+	\
 	if (proc_thermal_emum_mode == PROC_THERMAL_PLATFORM_DEV) { \
 		pdev = to_platform_device(dev); \
 		proc_dev = platform_get_drvdata(pdev); \
@@ -291,11 +296,6 @@ static int proc_thermal_add(struct device *dev,
 	*priv = proc_priv;
 
 	ret = proc_thermal_read_ppcc(proc_priv);
-	if (!ret) {
-		ret = sysfs_create_group(&dev->kobj,
-					 &power_limit_attribute_group);
-
-	}
 	if (ret)
 		return ret;
 
@@ -309,8 +309,7 @@ static int proc_thermal_add(struct device *dev,
 
 	proc_priv->int340x_zone = int340x_thermal_zone_add(adev, ops);
 	if (IS_ERR(proc_priv->int340x_zone)) {
-		ret = PTR_ERR(proc_priv->int340x_zone);
-		goto remove_group;
+		return PTR_ERR(proc_priv->int340x_zone);
 	} else
 		ret = 0;
 
@@ -324,9 +323,6 @@ static int proc_thermal_add(struct device *dev,
 
 remove_zone:
 	int340x_thermal_zone_remove(proc_priv->int340x_zone);
-remove_group:
-	sysfs_remove_group(&proc_priv->dev->kobj,
-			   &power_limit_attribute_group);
 
 	return ret;
 }
@@ -357,7 +353,10 @@ static int int3401_add(struct platform_device *pdev)
 	platform_set_drvdata(pdev, proc_priv);
 	proc_thermal_emum_mode = PROC_THERMAL_PLATFORM_DEV;
 
-	return 0;
+	dev_info(&pdev->dev, "Creating sysfs group for PROC_THERMAL_PLATFORM_DEV\n");
+
+	return sysfs_create_group(&pdev->dev.kobj,
+					 &power_limit_attribute_group);
 }
 
 static int int3401_remove(struct platform_device *pdev)
@@ -434,7 +433,10 @@ static int  proc_thermal_pci_probe(struct pci_dev *pdev,
 			dev_err(&pdev->dev, "No auxiliary DTSs enabled\n");
 	}
 
-	return 0;
+	dev_info(&pdev->dev, "Creating sysfs group for PROC_THERMAL_PCI\n");
+
+	return sysfs_create_group(&pdev->dev.kobj,
+					 &power_limit_attribute_group);
 }
 
 static void  proc_thermal_pci_remove(struct pci_dev *pdev)
Signature · 1 line
2.19.1
author maintainer
#23 lore raw

PATCH 23/52 staging: rtl8723bs: Fix build error with Clang when inlining is disabled

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 97715058b70da1262fd07798c8b2e3e894f759dd ]

When CONFIG_NO_AUTO_INLINE was present in linux-next (which added '-fno-inline-functions' to KBUILD_CFLAGS), an allyesconfig build with Clang failed at the modpost stage:

ERROR: "is_broadcast_mac_addr" [drivers/staging/rtl8723bs/r8723bs.ko] undefined!
ERROR: "is_zero_mac_addr" [drivers/staging/rtl8723bs/r8723bs.ko] undefined!
ERROR: "is_multicast_mac_addr" [drivers/staging/rtl8723bs/r8723bs.ko] undefined!

These functions were marked as extern inline, meaning that if inlining doesn't happen, the function will be undefined, as it is above.

This happens to work with GCC because the '-fno-inline-functions' option respects the __inline attribute so all instances of these functions are inlined as expected and the definition doesn't actually matter. However, with Clang and '-fno-inline-functions', a function has to be marked with the __always_inline attribute to be considered for inlining, which none of these functions are. Clang tries to find the symbol definition elsewhere as it was told and fails, which trickles down to modpost.

To make sure that this code compiles regardless of compiler and make the intention of the code clearer, use 'static' to ensure these functions are always defined, regardless of inlining. Additionally, silence a checkpatch warning by switching from '__inline' to 'inline'.

---
 drivers/staging/rtl8723bs/include/ieee80211.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/staging/rtl8723bs/include/ieee80211.h +3 -3
index 73ce63770c3ce..fa9c80fc77739 100644
@@ -1008,18 +1008,18 @@ enum ieee80211_state {
 #define IP_FMT "%pI4"
 #define IP_ARG(x) (x)
 
-extern __inline int is_multicast_mac_addr(const u8 *addr)
+static inline int is_multicast_mac_addr(const u8 *addr)
 {
         return ((addr[0] != 0xff) && (0x01 & addr[0]));
 }
 
-extern __inline int is_broadcast_mac_addr(const u8 *addr)
+static inline int is_broadcast_mac_addr(const u8 *addr)
 {
 	return ((addr[0] == 0xff) && (addr[1] == 0xff) && (addr[2] == 0xff) &&   \
 		(addr[3] == 0xff) && (addr[4] == 0xff) && (addr[5] == 0xff));
 }
 
-extern __inline int is_zero_mac_addr(const u8 *addr)
+static inline int is_zero_mac_addr(const u8 *addr)
 {
 	return ((addr[0] == 0x00) && (addr[1] == 0x00) && (addr[2] == 0x00) &&   \
 		(addr[3] == 0x00) && (addr[4] == 0x00) && (addr[5] == 0x00));
Signature · 1 line
2.19.1
author maintainer
#24 lore raw

PATCH 24/52 mac80211: fix miscounting of ttl-dropped frames

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit a0dc02039a2ee54fb4ae400e0b755ed30e73e58c ]

In ieee80211_rx_h_mesh_fwding, we increment the 'dropped_frames_ttl' counter when we decrement the ttl to zero. For unicast frames destined for other hosts, we stop processing the frame at that point.

For multicast frames, we do not rebroadcast it in this case, but we do pass the frame up the stack to process it on this STA. That doesn't match the usual definition of "dropped," so don't count those as such.

With this change, something like ping6 -i0.2 ff02::1%mesh0 from a peer in a ttl=1 network no longer increments the counter rapidly.

---
 net/mac80211/rx.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
net/mac80211/rx.c +3 -1
index c7ac1a480b1dd..dfc2af6833aff 100644
@@ -2533,7 +2533,9 @@ ieee80211_rx_h_mesh_fwding(struct ieee80211_rx_data *rx)
 	skb_set_queue_mapping(skb, q);
 
 	if (!--mesh_hdr->ttl) {
-		IEEE80211_IFSTA_MESH_CTR_INC(ifmsh, dropped_frames_ttl);
+		if (!is_multicast_ether_addr(hdr->addr1))
+			IEEE80211_IFSTA_MESH_CTR_INC(ifmsh,
+						     dropped_frames_ttl);
 		goto out;
 	}
 
Signature · 1 line
2.19.1
author maintainer
#25 lore raw

PATCH 25/52 sched/wait: Fix rcuwait_wake_up() ordering

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 6dc080eeb2ba01973bfff0d79844d7a59e12542e ]

For some peculiar reason rcuwait_wake_up() has the right barrier in the comment, but not in the code.

This mistake has been observed to cause a deadlock in the following situation:

    P1					P2

    percpu_up_read()			percpu_down_write()
      rcu_sync_is_idle() // false
					  rcu_sync_enter()
					  ...
      __percpu_up_read()
[S] ,-  __this_cpu_dec(*sem->read_count)
    |   smp_rmb();
[L] |   task = rcu_dereference(w->task) // NULL
    |
    |				    [S]	    w->task = current
    |					    smp_mb();
    |				    [L]	    readers_active_check() // fail
    `-> <store happens here>

Where the smp_rmb() (obviously) fails to constrain the store.

[ peterz: Added changelog. ]

Cc Linus Torvalds <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Thomas Gleixner <[email protected]>
Fixes 8f95c90ceb54 ("sched/wait, RCU: Introduce rcuwait machinery")
---
 kernel/exit.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/exit.c +1 -1
index 3aa01b74c1e36..5523fb0c20c8c 100644
@@ -306,7 +306,7 @@ void rcuwait_wake_up(struct rcuwait *w)
 	 *        MB (A)	      MB (B)
 	 *    [L] cond		  [L] tsk
 	 */
-	smp_rmb(); /* (B) */
+	smp_mb(); /* (B) */
 
 	/*
 	 * Avoid using task_rcu_dereference() magic as long as we are careful,
Signature · 1 line
2.19.1
author maintainer
#26 lore raw

PATCH 26/52 futex: Fix (possible) missed wakeup

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit b061c38bef43406df8e73c5be06cbfacad5ee6ad ]

We must not rely on wake_q_add() to delay the wakeup; in particular commit:

1d0dcb3ad9d3 ("futex: Implement lockless wakeups")

moved wake_q_add() before smp_store_release(&q->lock_ptr, NULL), which could result in futex_wait() waking before observing ->lock_ptr == NULL and going back to sleep again.

Cc Linus Torvalds <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Thomas Gleixner <[email protected]>
Fixes 1d0dcb3ad9d3 ("futex: Implement lockless wakeups")
---
 kernel/futex.c | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)
kernel/futex.c +8 -5
index 29d708d0b3d19..22f83064abb35 100644
@@ -1462,11 +1462,7 @@ static void mark_wake_futex(struct wake_q_head *wake_q, struct futex_q *q)
 	if (WARN(q->pi_state || q->rt_waiter, "refusing to wake PI futex\n"))
 		return;
 
-	/*
-	 * Queue the task for later wakeup for after we've released
-	 * the hb->lock. wake_q_add() grabs reference to p.
-	 */
-	wake_q_add(wake_q, p);
+	get_task_struct(p);
 	__unqueue_futex(q);
 	/*
 	 * The waiting task can free the futex_q as soon as q->lock_ptr = NULL
@@ -1476,6 +1472,13 @@ static void mark_wake_futex(struct wake_q_head *wake_q, struct futex_q *q)
 	 * plist_del in __unqueue_futex().
 	 */
 	smp_store_release(&q->lock_ptr, NULL);
+
+	/*
+	 * Queue the task for later wakeup for after we've released
+	 * the hb->lock. wake_q_add() grabs reference to p.
+	 */
+	wake_q_add(wake_q, p);
+	put_task_struct(p);
 }
 
 /*
Signature · 1 line
2.19.1
author maintainer
#27 lore raw

PATCH 27/52 locking/rwsem: Fix (possible) missed wakeup

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit e158488be27b157802753a59b336142dc0eb0380 ]

Because wake_q_add() can imply an immediate wakeup (cmpxchg failure case), we must not rely on the wakeup being delayed. However, commit:

e38513905eea ("locking/rwsem: Rework zeroing reader waiter->task")

relies on exactly that behaviour in that the wakeup must not happen until after we clear waiter->task.

[ peterz: Added changelog. ]

Cc Linus Torvalds <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Thomas Gleixner <[email protected]>
Fixes e38513905eea ("locking/rwsem: Rework zeroing reader waiter->task")
---
 kernel/locking/rwsem-xadd.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
kernel/locking/rwsem-xadd.c +9 -2
index a903367793758..c75017326c37a 100644
@@ -198,15 +198,22 @@ static void __rwsem_mark_wake(struct rw_semaphore *sem,
 		woken++;
 		tsk = waiter->task;
 
-		wake_q_add(wake_q, tsk);
+		get_task_struct(tsk);
 		list_del(&waiter->list);
 		/*
-		 * Ensure that the last operation is setting the reader
+		 * Ensure calling get_task_struct() before setting the reader
 		 * waiter to nil such that rwsem_down_read_failed() cannot
 		 * race with do_exit() by always holding a reference count
 		 * to the task to wakeup.
 		 */
 		smp_store_release(&waiter->task, NULL);
+		/*
+		 * Ensure issuing the wakeup (either by us or someone else)
+		 * after setting the reader waiter to nil.
+		 */
+		wake_q_add(wake_q, tsk);
+		/* wake_q_add() already take the task ref */
+		put_task_struct(tsk);
 	}
 
 	adjustment = woken * RWSEM_ACTIVE_READ_BIAS - adjustment;
Signature · 1 line
2.19.1
author maintainer
#28 lore raw

PATCH 28/52 drm/amd/powerplay: OD setting fix on Vega10

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 6d87dc97eb3341de3f7b1efa3156cb0e014f4a96 ]

gfxclk for OD setting is limited to 1980M for non-acg ASICs of Vega10

---
 .../powerplay/hwmgr/vega10_processpptables.c  | 22 ++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)
drivers/gpu/drm/amd/powerplay/hwmgr/vega10_processpptables.c +21 -1
index e343df1903754..05bb87a54e909 100644
@@ -32,6 +32,7 @@
 #include "vega10_pptable.h"
 
 #define NUM_DSPCLK_LEVELS 8
+#define VEGA10_ENGINECLOCK_HARDMAX 198000
 
 static void set_hw_cap(struct pp_hwmgr *hwmgr, bool enable,
 		enum phm_platform_caps cap)
@@ -258,7 +259,26 @@ static int init_over_drive_limits(
 		struct pp_hwmgr *hwmgr,
 		const ATOM_Vega10_POWERPLAYTABLE *powerplay_table)
 {
-	hwmgr->platform_descriptor.overdriveLimit.engineClock =
+	const ATOM_Vega10_GFXCLK_Dependency_Table *gfxclk_dep_table =
+			(const ATOM_Vega10_GFXCLK_Dependency_Table *)
+			(((unsigned long) powerplay_table) +
+			le16_to_cpu(powerplay_table->usGfxclkDependencyTableOffset));
+	bool is_acg_enabled = false;
+	ATOM_Vega10_GFXCLK_Dependency_Record_V2 *patom_record_v2;
+
+	if (gfxclk_dep_table->ucRevId == 1) {
+		patom_record_v2 =
+			(ATOM_Vega10_GFXCLK_Dependency_Record_V2 *)gfxclk_dep_table->entries;
+		is_acg_enabled =
+			(bool)patom_record_v2[gfxclk_dep_table->ucNumEntries-1].ucACGEnable;
+	}
+
+	if (powerplay_table->ulMaxODEngineClock > VEGA10_ENGINECLOCK_HARDMAX &&
+		!is_acg_enabled)
+		hwmgr->platform_descriptor.overdriveLimit.engineClock =
+			VEGA10_ENGINECLOCK_HARDMAX;
+	else
+		hwmgr->platform_descriptor.overdriveLimit.engineClock =
 			le32_to_cpu(powerplay_table->ulMaxODEngineClock);
 	hwmgr->platform_descriptor.overdriveLimit.memoryClock =
 			le32_to_cpu(powerplay_table->ulMaxODMemoryClock);
Signature · 1 line
2.19.1
author maintainer
#29 lore raw

PATCH 29/52 serial: fsl_lpuart: fix maximum acceptable baud rate with over-sampling

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 815d835b7ba46685c316b000013367dacb2b461b ]

Using over-sampling ratio, lpuart can accept baud rate upto uartclk / 4.

---
 drivers/tty/serial/fsl_lpuart.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/tty/serial/fsl_lpuart.c +1 -1
index 716c33b2a11cb..32a473f9d1d38 100644
@@ -1701,7 +1701,7 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
 	}
 
 	/* ask the core to calculate the divisor */
-	baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16);
+	baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 4);
 
 	spin_lock_irqsave(&sport->port.lock, flags);
 
Signature · 1 line
2.19.1
author maintainer
#30 lore raw

PATCH 30/52 staging: android: ion: Support cpu access during dma_buf_detach

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 31eb79db420a3f94c4c45a8c0a05cd30e333f981 ]

Often userspace doesn't know when the kernel will be calling dma_buf_detach on the buffer.
If userpace starts its CPU access at the same time as the sg list is being freed it could end up accessing the sg list after it has been freed.

Thread A Thread B
- DMA_BUF_IOCTL_SYNC IOCT
- ion_dma_buf_begin_cpu_access
- list_for_each_entry
- ion_dma_buf_detatch
- free_duped_table
- dma_sync_sg_for_cpu

Fix this by getting the ion_buffer lock before freeing the sg table memory.

Fixes 2a55e7b5e544 ("staging: android: ion: Call dma_map_sg for syncing and mapping")
---
 drivers/staging/android/ion/ion.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/staging/android/ion/ion.c +1 -1
index 24cb666c92242..dd96ca61a5152 100644
@@ -257,10 +257,10 @@ static void ion_dma_buf_detatch(struct dma_buf *dmabuf,
 	struct ion_dma_buf_attachment *a = attachment->priv;
 	struct ion_buffer *buffer = dmabuf->priv;
 
-	free_duped_table(a->table);
 	mutex_lock(&buffer->lock);
 	list_del(&a->list);
 	mutex_unlock(&buffer->lock);
+	free_duped_table(a->table);
 
 	kfree(a);
 }
Signature · 1 line
2.19.1
author maintainer
#31 lore raw

PATCH 31/52 direct-io: allow direct writes to empty inodes

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 8b9433eb4de3c26a9226c981c283f9f4896ae030 ]

On a DIO_SKIP_HOLES filesystem, the ->get_block() method is currently not allowed to create blocks for an empty inode. This confusion comes from trying to bit shift a negative number, so check the size of the inode first.

The problem is most visible for hfsplus, because the fallback to buffered I/O doesn't happen and the write fails with EIO. This is in part the fault of the module, because it gives a wrong return value on ->get_block(); that will be fixed in a separate patch.

---
 fs/direct-io.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
fs/direct-io.c +3 -2
index 40567501015f2..2c90d541f5275 100644
@@ -658,6 +658,7 @@ static int get_more_blocks(struct dio *dio, struct dio_submit *sdio,
 	unsigned long fs_count;	/* Number of filesystem-sized blocks */
 	int create;
 	unsigned int i_blkbits = sdio->blkbits + sdio->blkfactor;
+	loff_t i_size;
 
 	/*
 	 * If there was a memory error and we've overwritten all the
@@ -687,8 +688,8 @@ static int get_more_blocks(struct dio *dio, struct dio_submit *sdio,
 		 */
 		create = dio->op == REQ_OP_WRITE;
 		if (dio->flags & DIO_SKIP_HOLES) {
-			if (fs_startblk <= ((i_size_read(dio->inode) - 1) >>
-							i_blkbits))
+			i_size = i_size_read(dio->inode);
+			if (i_size && fs_startblk <= (i_size - 1) >> i_blkbits)
 				create = 0;
 		}
 
Signature · 1 line
2.19.1
author maintainer
#32 lore raw

PATCH 32/52 writeback: synchronize sync(2) against cgroup writeback membership switches

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 7fc5854f8c6efae9e7624970ab49a1eac2faefb1 ]

sync_inodes_sb() can race against cgwb (cgroup writeback) membership switches and fail to writeback some inodes. For example, if an inode switches to another wb while sync_inodes_sb() is in progress, the new wb might not be visible to bdi_split_work_to_wbs() at all or the inode might jump from a wb which hasn't issued writebacks yet to one which already has.

This patch adds backing_dev_info->wb_switch_rwsem to synchronize cgwb switch path against sync_inodes_sb() so that sync_inodes_sb() is guaranteed to see all the target wbs and inodes can't jump wbs to escape syncing.

v2: Fixed misplaced rwsem init. Spotted by Jiufei.

---
 fs/fs-writeback.c                | 40 ++++++++++++++++++++++++++++++--
 include/linux/backing-dev-defs.h |  1 +
 mm/backing-dev.c                 |  1 +
 3 files changed, 40 insertions(+), 2 deletions(-)
fs/fs-writeback.c +38 -2
index 3244932f4d5cc..6a76616c9401b 100644
@@ -331,11 +331,22 @@ struct inode_switch_wbs_context {
 	struct work_struct	work;
 };
 
+static void bdi_down_write_wb_switch_rwsem(struct backing_dev_info *bdi)
+{
+	down_write(&bdi->wb_switch_rwsem);
+}
+
+static void bdi_up_write_wb_switch_rwsem(struct backing_dev_info *bdi)
+{
+	up_write(&bdi->wb_switch_rwsem);
+}
+
 static void inode_switch_wbs_work_fn(struct work_struct *work)
 {
 	struct inode_switch_wbs_context *isw =
 		container_of(work, struct inode_switch_wbs_context, work);
 	struct inode *inode = isw->inode;
+	struct backing_dev_info *bdi = inode_to_bdi(inode);
 	struct address_space *mapping = inode->i_mapping;
 	struct bdi_writeback *old_wb = inode->i_wb;
 	struct bdi_writeback *new_wb = isw->new_wb;
@@ -343,6 +354,12 @@ static void inode_switch_wbs_work_fn(struct work_struct *work)
 	bool switched = false;
 	void **slot;
 
+	/*
+	 * If @inode switches cgwb membership while sync_inodes_sb() is
+	 * being issued, sync_inodes_sb() might miss it.  Synchronize.
+	 */
+	down_read(&bdi->wb_switch_rwsem);
+
 	/*
 	 * By the time control reaches here, RCU grace period has passed
 	 * since I_WB_SWITCH assertion and all wb stat update transactions
@@ -435,6 +452,8 @@ static void inode_switch_wbs_work_fn(struct work_struct *work)
 	spin_unlock(&new_wb->list_lock);
 	spin_unlock(&old_wb->list_lock);
 
+	up_read(&bdi->wb_switch_rwsem);
+
 	if (switched) {
 		wb_wakeup(new_wb);
 		wb_put(old_wb);
@@ -475,9 +494,18 @@ static void inode_switch_wbs(struct inode *inode, int new_wb_id)
 	if (inode->i_state & I_WB_SWITCH)
 		return;
 
+	/*
+	 * Avoid starting new switches while sync_inodes_sb() is in
+	 * progress.  Otherwise, if the down_write protected issue path
+	 * blocks heavily, we might end up starting a large number of
+	 * switches which will block on the rwsem.
+	 */
+	if (!down_read_trylock(&bdi->wb_switch_rwsem))
+		return;
+
 	isw = kzalloc(sizeof(*isw), GFP_ATOMIC);
 	if (!isw)
-		return;
+		goto out_unlock;
 
 	/* find and pin the new wb */
 	rcu_read_lock();
@@ -511,12 +539,14 @@ static void inode_switch_wbs(struct inode *inode, int new_wb_id)
 	 * Let's continue after I_WB_SWITCH is guaranteed to be visible.
 	 */
 	call_rcu(&isw->rcu_head, inode_switch_wbs_rcu_fn);
-	return;
+	goto out_unlock;
 
 out_free:
 	if (isw->new_wb)
 		wb_put(isw->new_wb);
 	kfree(isw);
+out_unlock:
+	up_read(&bdi->wb_switch_rwsem);
 }
 
 /**
@@ -894,6 +924,9 @@ fs_initcall(cgroup_writeback_init);
 
 #else	/* CONFIG_CGROUP_WRITEBACK */
 
+static void bdi_down_write_wb_switch_rwsem(struct backing_dev_info *bdi) { }
+static void bdi_up_write_wb_switch_rwsem(struct backing_dev_info *bdi) { }
+
 static struct bdi_writeback *
 locked_inode_to_wb_and_lock_list(struct inode *inode)
 	__releases(&inode->i_lock)
@@ -2408,8 +2441,11 @@ void sync_inodes_sb(struct super_block *sb)
 		return;
 	WARN_ON(!rwsem_is_locked(&sb->s_umount));
 
+	/* protect against inode wb switch, see inode_switch_wbs_work_fn() */
+	bdi_down_write_wb_switch_rwsem(bdi);
 	bdi_split_work_to_wbs(bdi, &work, false);
 	wb_wait_for_completion(bdi, &done);
+	bdi_up_write_wb_switch_rwsem(bdi);
 
 	wait_sb_inodes(sb);
 }
include/linux/backing-dev-defs.h +1 -0
index 19240379637fe..b186c4b464e02 100644
@@ -165,6 +165,7 @@ struct backing_dev_info {
 	struct radix_tree_root cgwb_tree; /* radix tree of active cgroup wbs */
 	struct rb_root cgwb_congested_tree; /* their congested states */
 	struct mutex cgwb_release_mutex;  /* protect shutdown of wb structs */
+	struct rw_semaphore wb_switch_rwsem; /* no cgwb switch while syncing */
 #else
 	struct bdi_writeback_congested *wb_congested;
 #endif
mm/backing-dev.c +1 -0
index 9386c98dac123..6fa31754eadd9 100644
@@ -684,6 +684,7 @@ static int cgwb_bdi_init(struct backing_dev_info *bdi)
 	INIT_RADIX_TREE(&bdi->cgwb_tree, GFP_ATOMIC);
 	bdi->cgwb_congested_tree = RB_ROOT;
 	mutex_init(&bdi->cgwb_release_mutex);
+	init_rwsem(&bdi->wb_switch_rwsem);
 
 	ret = wb_init(&bdi->wb, bdi, 1, GFP_KERNEL);
 	if (!ret) {
Signature · 1 line
2.19.1
author maintainer
#33 lore raw

PATCH 33/52 scsi: csiostor: fix NULL pointer dereference in csio_vport_set_state()

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit fe35a40e675473eb65f2f5462b82770f324b5689 ]

Assign fc_vport to ln->fc_vport before calling csio_fcoe_alloc_vnp() to avoid a NULL pointer dereference in csio_vport_set_state().

ln->fc_vport is dereferenced in csio_vport_set_state().

---
 drivers/scsi/csiostor/csio_attr.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/scsi/csiostor/csio_attr.c +1 -1
index 2d1c4ebd40f91..6587f20cff1a1 100644
@@ -582,12 +582,12 @@ csio_vport_create(struct fc_vport *fc_vport, bool disable)
 	}
 
 	fc_vport_set_state(fc_vport, FC_VPORT_INITIALIZING);
+	ln->fc_vport = fc_vport;
 
 	if (csio_fcoe_alloc_vnp(hw, ln))
 		goto error;
 
 	*(struct csio_lnode **)fc_vport->dd_data = ln;
-	ln->fc_vport = fc_vport;
 	if (!fc_vport->node_name)
 		fc_vport->node_name = wwn_to_u64(csio_ln_wwnn(ln));
 	if (!fc_vport->port_name)
Signature · 1 line
2.19.1
author maintainer
#34 lore raw

PATCH 34/52 net: altera_tse: fix connect_local_phy error path

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 17b42a20d7ca59377788c6a2409e77569570cc10 ]

The connect_local_phy should return NULL (not negative errno) on error, since its caller expects it.

---
 drivers/net/ethernet/altera/altera_tse_main.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/net/ethernet/altera/altera_tse_main.c +3 -1
index 527908c7e3845..84def1ff6cb64 100644
@@ -714,8 +714,10 @@ static struct phy_device *connect_local_phy(struct net_device *dev)
 
 		phydev = phy_connect(dev, phy_id_fmt, &altera_tse_adjust_link,
 				     priv->phy_iface);
-		if (IS_ERR(phydev))
+		if (IS_ERR(phydev)) {
 			netdev_err(dev, "Could not attach to PHY\n");
+			phydev = NULL;
+		}
 
 	} else {
 		int ret;
Signature · 1 line
2.19.1
author maintainer
#35 lore raw

PATCH 35/52 hv_netvsc: Fix ethtool change hash key error

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit b4a10c750424e01b5e37372fef0a574ebf7b56c3 ]

Hyper-V hosts require us to disable RSS before changing RSS key, otherwise the changing request will fail. This patch fixes the coding error.

Fixes ff4a44199012 ("netvsc: allow get/set of RSS indirection table")
[sl: fix up subject line]
---
 drivers/net/hyperv/rndis_filter.c | 25 +++++++++++++++++++------
 1 file changed, 19 insertions(+), 6 deletions(-)
drivers/net/hyperv/rndis_filter.c +19 -6
index 17025d46bdac8..fc1d5e14d83e9 100644
@@ -711,8 +711,8 @@ rndis_filter_set_offload_params(struct net_device *ndev,
 	return ret;
 }
 
-int rndis_filter_set_rss_param(struct rndis_device *rdev,
-			       const u8 *rss_key)
+static int rndis_set_rss_param_msg(struct rndis_device *rdev,
+				   const u8 *rss_key, u16 flag)
 {
 	struct net_device *ndev = rdev->ndev;
 	struct rndis_request *request;
@@ -741,7 +741,7 @@ int rndis_filter_set_rss_param(struct rndis_device *rdev,
 	rssp->hdr.type = NDIS_OBJECT_TYPE_RSS_PARAMETERS;
 	rssp->hdr.rev = NDIS_RECEIVE_SCALE_PARAMETERS_REVISION_2;
 	rssp->hdr.size = sizeof(struct ndis_recv_scale_param);
-	rssp->flag = 0;
+	rssp->flag = flag;
 	rssp->hashinfo = NDIS_HASH_FUNC_TOEPLITZ | NDIS_HASH_IPV4 |
 			 NDIS_HASH_TCP_IPV4 | NDIS_HASH_IPV6 |
 			 NDIS_HASH_TCP_IPV6;
@@ -766,9 +766,12 @@ int rndis_filter_set_rss_param(struct rndis_device *rdev,
 
 	wait_for_completion(&request->wait_event);
 	set_complete = &request->response_msg.msg.set_complete;
-	if (set_complete->status == RNDIS_STATUS_SUCCESS)
-		memcpy(rdev->rss_key, rss_key, NETVSC_HASH_KEYLEN);
-	else {
+	if (set_complete->status == RNDIS_STATUS_SUCCESS) {
+		if (!(flag & NDIS_RSS_PARAM_FLAG_DISABLE_RSS) &&
+		    !(flag & NDIS_RSS_PARAM_FLAG_HASH_KEY_UNCHANGED))
+			memcpy(rdev->rss_key, rss_key, NETVSC_HASH_KEYLEN);
+
+	} else {
 		netdev_err(ndev, "Fail to set RSS parameters:0x%x\n",
 			   set_complete->status);
 		ret = -EINVAL;
@@ -779,6 +782,16 @@ int rndis_filter_set_rss_param(struct rndis_device *rdev,
 	return ret;
 }
 
+int rndis_filter_set_rss_param(struct rndis_device *rdev,
+			       const u8 *rss_key)
+{
+	/* Disable RSS before change */
+	rndis_set_rss_param_msg(rdev, rss_key,
+				NDIS_RSS_PARAM_FLAG_DISABLE_RSS);
+
+	return rndis_set_rss_param_msg(rdev, rss_key, 0);
+}
+
 static int rndis_filter_query_device_link_status(struct rndis_device *dev,
 						 struct netvsc_device *net_device)
 {
Signature · 1 line
2.19.1
author maintainer
#36 lore raw

PATCH 36/52 net: usb: asix: ax88772_bind return error when hw_reset fail

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 6eea3527e68acc22483f4763c8682f223eb90029 ]

The ax88772_bind() should return error code immediately when the PHY was not reset properly through ax88772a_hw_reset(). Otherwise, The asix_get_phyid() will block when get the PHY Identifier from the PHYSID1 MII registers through asix_mdio_read() due to the PHY isn't ready. Furthermore, it will produce a lot of error message cause system crash.As follows:
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to send
software reset: ffffffb9
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
reg index 0x0000: -71
...

---
 drivers/net/usb/asix_devices.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)
drivers/net/usb/asix_devices.c +7 -2
index b1b3d8f7e67dd..d0c0ac0c3519c 100644
@@ -731,8 +731,13 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &chipcode, 0);
 	chipcode &= AX_CHIPCODE_MASK;
 
-	(chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) :
-					    ax88772a_hw_reset(dev, 0);
+	ret = (chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) :
+						  ax88772a_hw_reset(dev, 0);
+
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Failed to reset AX88772: %d\n", ret);
+		return ret;
+	}
 
 	/* Read PHYID register *AFTER* the PHY was reset properly */
 	phyid = asix_get_phyid(dev);
Signature · 1 line
2.19.1
author maintainer
#37 lore raw

PATCH 37/52 net: dev_is_mac_header_xmit() true for ARPHRD_RAWIP

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 3b707c3008cad04604c1f50e39f456621821c414 ]

__bpf_redirect() and act_mirred checks this boolean to determine whether to prefix an ethernet header.

---
 include/linux/if_arp.h | 1 +
 1 file changed, 1 insertion(+)
include/linux/if_arp.h +1 -0
index 3355efc897816..4125f60ee53b0 100644
@@ -54,6 +54,7 @@ static inline bool dev_is_mac_header_xmit(const struct net_device *dev)
 	case ARPHRD_IPGRE:
 	case ARPHRD_VOID:
 	case ARPHRD_NONE:
+	case ARPHRD_RAWIP:
 		return false;
 	default:
 		return true;
Signature · 1 line
2.19.1
author maintainer
#38 lore raw

PATCH 38/52 ibmveth: Do not process frames after calling napi_reschedule

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit e95d22c69b2c130ccce257b84daf283fd82d611e ]

The IBM virtual ethernet driver's polling function continues to process frames after rescheduling NAPI, resulting in a warning if it exhausted its budget. Do not restart polling after calling napi_reschedule. Instead let frames be processed in the following instance.

---
 drivers/net/ethernet/ibm/ibmveth.c | 2 --
 1 file changed, 2 deletions(-)
drivers/net/ethernet/ibm/ibmveth.c +0 -2
index 6c05819d995ea..754dff4c1771e 100644
@@ -1314,7 +1314,6 @@ static int ibmveth_poll(struct napi_struct *napi, int budget)
 	unsigned long lpar_rc;
 	u16 mss = 0;
 
-restart_poll:
 	while (frames_processed < budget) {
 		if (!ibmveth_rxq_pending_buffer(adapter))
 			break;
@@ -1402,7 +1401,6 @@ static int ibmveth_poll(struct napi_struct *napi, int budget)
 		    napi_reschedule(napi)) {
 			lpar_rc = h_vio_signal(adapter->vdev->unit_address,
 					       VIO_IRQ_DISABLE);
-			goto restart_poll;
 		}
 	}
 
Signature · 1 line
2.19.1
author maintainer
#39 lore raw

PATCH 39/52 mac80211: dont initiate TDLS connection if station is not associated to AP

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 7ed5285396c257fd4070b1e29e7b2341aae2a1ce ]

Following call trace is observed while adding TDLS peer entry in driver during TDLS setup.

Call Trace:
[<c1301476>] dump_stack+0x47/0x61
[<c10537d2>] __warn+0xe2/0x100
[<fa22415f>] ? sta_apply_parameters+0x49f/0x550 [mac80211]
[<c1053895>] warn_slowpath_null+0x25/0x30
[<fa22415f>] sta_apply_parameters+0x49f/0x550 [mac80211]
[<fa20ad42>] ? sta_info_alloc+0x1c2/0x450 [mac80211]
[<fa224623>] ieee80211_add_station+0xe3/0x160 [mac80211]
[<c1876fe3>] nl80211_new_station+0x273/0x420
[<c170f6d9>] genl_rcv_msg+0x219/0x3c0
[<c170f4c0>] ? genl_rcv+0x30/0x30
[<c170ee7e>] netlink_rcv_skb+0x8e/0xb0
[<c170f4ac>] genl_rcv+0x1c/0x30
[<c170e8aa>] netlink_unicast+0x13a/0x1d0
[<c170ec18>] netlink_sendmsg+0x2d8/0x390
[<c16c5acd>] sock_sendmsg+0x2d/0x40
[<c16c6369>] ___sys_sendmsg+0x1d9/0x1e0

Fixing this by allowing TDLS setup request only when we have completed association.

---
 net/mac80211/cfg.c | 4 ++++
 1 file changed, 4 insertions(+)
net/mac80211/cfg.c +4 -0
index ebc8045ddee68..150dd2160cefb 100644
@@ -1466,6 +1466,10 @@ static int ieee80211_add_station(struct wiphy *wiphy, struct net_device *dev,
 	if (params->sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER))
 		sta->sta.tdls = true;
 
+	if (sta->sta.tdls && sdata->vif.type == NL80211_IFTYPE_STATION &&
+	    !sdata->u.mgd.associated)
+		return -EINVAL;
+
 	err = sta_apply_parameters(local, sta, params);
 	if (err) {
 		sta_info_free(local, sta);
Signature · 1 line
2.19.1
author maintainer
#40 lore raw

PATCH 40/52 mac80211: Add attribute aligned(2) to struct action

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 7c53eb5d87bc21464da4268c3c0c47457b6d9c9b ]

During refactor in commit 9e478066eae4 ("mac80211: fix MU-MIMO follow-MAC mode") a new struct 'action' was declared with packed attribute as:

  struct {
          struct ieee80211_hdr_3addr hdr;
          u8 category;
          u8 action_code;
  } __packed action;

But since struct 'ieee80211_hdr_3addr' is declared with an aligned keyword as:

  struct ieee80211_hdr {
  	__le16 frame_control;
  	__le16 duration_id;
  	u8 addr1[ETH_ALEN];
  	u8 addr2[ETH_ALEN];
  	u8 addr3[ETH_ALEN];
  	__le16 seq_ctrl;
  	u8 addr4[ETH_ALEN];
  } __packed __aligned(2);

Solve the ambiguity of placing aligned structure in a packed one by adding the aligned(2) attribute to struct 'action'.

This removes the following warning (W=1):

net/mac80211/rx.c:234:2: warning: alignment 1 of 'struct <anonymous>' is less than 2 [-Wpacked-not-aligned]

---
 net/mac80211/rx.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/mac80211/rx.c +1 -1
index dfc2af6833aff..1512e547a5e05 100644
@@ -206,7 +206,7 @@ static void ieee80211_handle_mu_mimo_mon(struct ieee80211_sub_if_data *sdata,
 		struct ieee80211_hdr_3addr hdr;
 		u8 category;
 		u8 action_code;
-	} __packed action;
+	} __packed __aligned(2) action;
 
 	if (!sdata)
 		return;
Signature · 1 line
2.19.1
author maintainer
#41 lore raw

PATCH 41/52 cfg80211: extend range deviation for DMG

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 93183bdbe73bbdd03e9566c8dc37c9d06b0d0db6 ]

Recently, DMG frequency bands have been extended till 71GHz, so extend the range check till 20GHz (45-71GHZ), else some channels will be marked as disabled.

---
 net/wireless/reg.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
net/wireless/reg.c +2 -2
index bd91de4160353..ebfbc3f1be428 100644
@@ -759,7 +759,7 @@ static bool is_valid_rd(const struct ieee80211_regdomain *rd)
  * definitions (the "2.4 GHz band", the "5 GHz band" and the "60GHz band"),
  * however it is safe for now to assume that a frequency rule should not be
  * part of a frequency's band if the start freq or end freq are off by more
- * than 2 GHz for the 2.4 and 5 GHz bands, and by more than 10 GHz for the
+ * than 2 GHz for the 2.4 and 5 GHz bands, and by more than 20 GHz for the
  * 60 GHz band.
  * This resolution can be lowered and should be considered as we add
  * regulatory rule support for other "bands".
@@ -774,7 +774,7 @@ static bool freq_in_rule_band(const struct ieee80211_freq_range *freq_range,
 	 * with the Channel starting frequency above 45 GHz.
 	 */
 	u32 limit = freq_khz > 45 * ONE_GHZ_IN_KHZ ?
-			10 * ONE_GHZ_IN_KHZ : 2 * ONE_GHZ_IN_KHZ;
+			20 * ONE_GHZ_IN_KHZ : 2 * ONE_GHZ_IN_KHZ;
 	if (abs(freq_khz - freq_range->start_freq_khz) <= limit)
 		return true;
 	if (abs(freq_khz - freq_range->end_freq_khz) <= limit)
Signature · 1 line
2.19.1
author maintainer
#42 lore raw

PATCH 42/52 svm: Fix AVIC incomplete IPI emulation

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit bb218fbcfaaa3b115d4cd7a43c0ca164f3a96e57 ]

In case of incomplete IPI with invalid interrupt type, the current SVM driver does not properly emulate the IPI, and fails to boot FreeBSD guests with multiple vcpus when enabling AVIC.

Fix this by update APIC ICR high/low registers, which also emulate sending the IPI.

---
 arch/x86/kvm/svm.c | 19 ++++---------------
 1 file changed, 4 insertions(+), 15 deletions(-)
arch/x86/kvm/svm.c +4 -15
index 656ac12f54392..a94beaecd3e02 100644
@@ -4006,25 +4006,14 @@ static int avic_incomplete_ipi_interception(struct vcpu_svm *svm)
 		kvm_lapic_reg_write(apic, APIC_ICR, icrl);
 		break;
 	case AVIC_IPI_FAILURE_TARGET_NOT_RUNNING: {
-		int i;
-		struct kvm_vcpu *vcpu;
-		struct kvm *kvm = svm->vcpu.kvm;
 		struct kvm_lapic *apic = svm->vcpu.arch.apic;
 
 		/*
-		 * At this point, we expect that the AVIC HW has already
-		 * set the appropriate IRR bits on the valid target
-		 * vcpus. So, we just need to kick the appropriate vcpu.
+		 * Update ICR high and low, then emulate sending IPI,
+		 * which is handled when writing APIC_ICR.
 		 */
-		kvm_for_each_vcpu(i, vcpu, kvm) {
-			bool m = kvm_apic_match_dest(vcpu, apic,
-						     icrl & KVM_APIC_SHORT_MASK,
-						     GET_APIC_DEST_FIELD(icrh),
-						     icrl & KVM_APIC_DEST_MASK);
-
-			if (m && !avic_vcpu_is_running(vcpu))
-				kvm_vcpu_wake_up(vcpu);
-		}
+		kvm_lapic_reg_write(apic, APIC_ICR2, icrh);
+		kvm_lapic_reg_write(apic, APIC_ICR, icrl);
 		break;
 	}
 	case AVIC_IPI_FAILURE_INVALID_TARGET:
Signature · 1 line
2.19.1
author maintainer
#43 lore raw

PATCH 43/52 KVM: nSVM: clear events pending from svm_complete_interrupts() when exiting to L1

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

[ Upstream commit 619ad846fc3452adaf71ca246c5aa711e2055398 ]

kvm-unit-tests' eventinj "NMI failing on IDT" test results in NMI being delivered to the host (L1) when it's running nested. The problem seems to
be: svm_complete_interrupts() raises 'nmi_injected' flag but later we decide to reflect EXIT_NPF to L1. The flag remains pending and we do NMI injection upon entry so it got delivered to L1 instead of L2.

It seems that VMX code solves the same issue in prepare_vmcs12(), this was introduced with code refactoring in commit 5f3d5799974b ("KVM: nVMX: Rework event injection and recovery").

---
 arch/x86/kvm/svm.c | 8 ++++++++
 1 file changed, 8 insertions(+)
arch/x86/kvm/svm.c +8 -0
index a94beaecd3e02..c387047e926a2 100644
@@ -2929,6 +2929,14 @@ static int nested_svm_vmexit(struct vcpu_svm *svm)
 	kvm_mmu_reset_context(&svm->vcpu);
 	kvm_mmu_load(&svm->vcpu);
 
+	/*
+	 * Drop what we picked up for L2 via svm_complete_interrupts() so it
+	 * doesn't end up in L1.
+	 */
+	svm->vcpu.arch.nmi_injected = false;
+	kvm_clear_exception_queue(&svm->vcpu);
+	kvm_clear_interrupt_queue(&svm->vcpu);
+
 	return 0;
 }
 
Signature · 1 line
2.19.1
author maintainer
#44 lore raw

PATCH 44/52 powerpc: Always initialize input array when calling epapr_hypercall()

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Seth Forshee <[email protected]>

commit 186b8f1587c79c2fa04bfa392fdf084443e398c1 upstream.

Several callers to epapr_hypercall() pass an uninitialized stack allocated array for the input arguments, presumably because they have no input arguments. However this can produce errors like this one

arch/powerpc/include/asm/epapr_hcalls.h:470:42: error: 'in' may be used uninitialized in this function [-Werror=maybe-uninitialized]

  unsigned long register r3 asm("r3") = in[0];
                                        ~~^~~

Fix callers to this function to always zero-initialize the input arguments array to prevent this.

---
 arch/powerpc/include/asm/epapr_hcalls.h |   12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
arch/powerpc/include/asm/epapr_hcalls.h +6 -6
@@ -508,7 +508,7 @@ static unsigned long epapr_hypercall(uns
 
 static inline long epapr_hypercall0_1(unsigned int nr, unsigned long *r2)
 {
-	unsigned long in[8];
+	unsigned long in[8] = {0};
 	unsigned long out[8];
 	unsigned long r;
 
@@ -520,7 +520,7 @@ static inline long epapr_hypercall0_1(un
 
 static inline long epapr_hypercall0(unsigned int nr)
 {
-	unsigned long in[8];
+	unsigned long in[8] = {0};
 	unsigned long out[8];
 
 	return epapr_hypercall(in, out, nr);
@@ -528,7 +528,7 @@ static inline long epapr_hypercall0(unsi
 
 static inline long epapr_hypercall1(unsigned int nr, unsigned long p1)
 {
-	unsigned long in[8];
+	unsigned long in[8] = {0};
 	unsigned long out[8];
 
 	in[0] = p1;
@@ -538,7 +538,7 @@ static inline long epapr_hypercall1(unsi
 static inline long epapr_hypercall2(unsigned int nr, unsigned long p1,
 				    unsigned long p2)
 {
-	unsigned long in[8];
+	unsigned long in[8] = {0};
 	unsigned long out[8];
 
 	in[0] = p1;
@@ -549,7 +549,7 @@ static inline long epapr_hypercall2(unsi
 static inline long epapr_hypercall3(unsigned int nr, unsigned long p1,
 				    unsigned long p2, unsigned long p3)
 {
-	unsigned long in[8];
+	unsigned long in[8] = {0};
 	unsigned long out[8];
 
 	in[0] = p1;
@@ -562,7 +562,7 @@ static inline long epapr_hypercall4(unsi
 				    unsigned long p2, unsigned long p3,
 				    unsigned long p4)
 {
-	unsigned long in[8];
+	unsigned long in[8] = {0};
 	unsigned long out[8];
 
 	in[0] = p1;
author maintainer
#45 lore raw

PATCH 45/52 mmc: spi: Fix card detection during probe

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jonathan Neuschäfer <[email protected]>

commit c9bd505dbd9d3dc80c496f88eafe70affdcf1ba6 upstream.

When using the mmc_spi driver with a card-detect pin, I noticed that the card was not detected immediately after probe, but only after it was unplugged and plugged back in (and the CD IRQ fired).

The call tree looks something like this:

mmc_spi_probe
mmc_add_host

    mmc_start_host
      _mmc_detect_change
        mmc_schedule_delayed_work(&host->detect, 0)
          mmc_rescan
            host->bus_ops->detect(host)
              mmc_detect
                _mmc_detect_card_removed
                  host->ops->get_cd(host)
                    mmc_gpio_get_cd -> -ENOSYS (ctx->cd_gpio not set)
  mmc_gpiod_request_cd
    ctx->cd_gpio = desc

To fix this issue, call mmc_detect_change after the card-detect GPIO/IRQ is registered.

---
 drivers/mmc/host/mmc_spi.c |    1 +
 1 file changed, 1 insertion(+)
drivers/mmc/host/mmc_spi.c +1 -0
@@ -1447,6 +1447,7 @@ static int mmc_spi_probe(struct spi_devi
 		mmc->caps &= ~MMC_CAP_NEEDS_POLL;
 		mmc_gpiod_request_cd_irq(mmc);
 	}
+	mmc_detect_change(mmc, 0);
 
 	if (host->pdata && host->pdata->flags & MMC_SPI_USE_RO_GPIO) {
 		has_ro = true;
author maintainer
#46 lore raw

PATCH 46/52 mmc: tmio_mmc_core: dont claim spurious interrupts

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Sergei Shtylyov <[email protected]>

commit 5c27ff5db1491a947264d6d4e4cbe43ae6535bae upstream.

I have encountered an interrupt storm during the eMMC chip probing (and the chip finally didn't get detected). It turned out that U-Boot left the DMAC interrupts enabled while the Linux driver didn't use those. The SDHI driver's interrupt handler somehow assumes that, even if an SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think that if none of the enabled interrupts happened and got handled, we should return IRQ_NONE -- that way the kernel IRQ code recoginizes a spurious interrupt and masks it off pretty quickly...

---
 drivers/mmc/host/tmio_mmc_core.c |   11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)
drivers/mmc/host/tmio_mmc_core.c +7 -4
@@ -688,7 +688,7 @@ static bool __tmio_mmc_sdcard_irq(struct
 	return false;
 }
 
-static void __tmio_mmc_sdio_irq(struct tmio_mmc_host *host)
+static bool __tmio_mmc_sdio_irq(struct tmio_mmc_host *host)
 {
 	struct mmc_host *mmc = host->mmc;
 	struct tmio_mmc_data *pdata = host->pdata;
@@ -696,7 +696,7 @@ static void __tmio_mmc_sdio_irq(struct t
 	unsigned int sdio_status;
 
 	if (!(pdata->flags & TMIO_MMC_SDIO_IRQ))
-		return;
+		return false;
 
 	status = sd_ctrl_read16(host, CTL_SDIO_STATUS);
 	ireg = status & TMIO_SDIO_MASK_ALL & ~host->sdio_irq_mask;
@@ -709,6 +709,8 @@ static void __tmio_mmc_sdio_irq(struct t
 
 	if (mmc->caps & MMC_CAP_SDIO_IRQ && ireg & TMIO_SDIO_STAT_IOIRQ)
 		mmc_signal_sdio_irq(mmc);
+
+	return ireg;
 }
 
 irqreturn_t tmio_mmc_irq(int irq, void *devid)
@@ -727,9 +729,10 @@ irqreturn_t tmio_mmc_irq(int irq, void *
 	if (__tmio_mmc_sdcard_irq(host, ireg, status))
 		return IRQ_HANDLED;
 
-	__tmio_mmc_sdio_irq(host);
+	if (__tmio_mmc_sdio_irq(host))
+		return IRQ_HANDLED;
 
-	return IRQ_HANDLED;
+	return IRQ_NONE;
 }
 EXPORT_SYMBOL_GPL(tmio_mmc_irq);
 
author maintainer
#47 lore raw

PATCH 47/52 mmc: tmio: fix access width of Block Count Register

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Takeshi Saito <[email protected]>

commit 5603731a15ef9ca317c122cc8c959f1dee1798b4 upstream.

In R-Car Gen2 or later, the maximum number of transfer blocks are changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register should use iowrite32().

If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this value will not be cleared. So, SD/MMC card initialization fails.

So, check for the bigger register and use apropriate write. Also, mark the register as extended on Gen2.

[wsa: use max_blk_count in if(), add Gen2, update commit message]
[Ulf: Fixed build error]
---
 drivers/mmc/host/renesas_sdhi_sys_dmac.c |    1 +
 drivers/mmc/host/tmio_mmc.h              |    5 +++++
 drivers/mmc/host/tmio_mmc_core.c         |    6 +++++-
 3 files changed, 11 insertions(+), 1 deletion(-)
drivers/mmc/host/renesas_sdhi_sys_dmac.c +1 -0
@@ -68,6 +68,7 @@ static const struct renesas_sdhi_of_data
 	.scc_offset	= 0x0300,
 	.taps		= rcar_gen2_scc_taps,
 	.taps_num	= ARRAY_SIZE(rcar_gen2_scc_taps),
+	.max_blk_count  = 0xffffffff,
 };
 
 /* Definitions for sampling clocks */
drivers/mmc/host/tmio_mmc.h +5 -0
@@ -286,6 +286,11 @@ static inline void sd_ctrl_write32_as_16
 	writew(val >> 16, host->ctl + ((addr + 2) << host->bus_shift));
 }
 
+static inline void sd_ctrl_write32(struct tmio_mmc_host *host, int addr, u32 val)
+{
+	iowrite32(val, host->ctl + (addr << host->bus_shift));
+}
+
 static inline void sd_ctrl_write32_rep(struct tmio_mmc_host *host, int addr,
 				       const u32 *buf, int count)
 {
drivers/mmc/host/tmio_mmc_core.c +5 -1
@@ -46,6 +46,7 @@
 #include <linux/regulator/consumer.h>
 #include <linux/mmc/sdio.h>
 #include <linux/scatterlist.h>
+#include <linux/sizes.h>
 #include <linux/spinlock.h>
 #include <linux/swiotlb.h>
 #include <linux/workqueue.h>
@@ -761,7 +762,10 @@ static int tmio_mmc_start_data(struct tm
 
 	/* Set transfer length / blocksize */
 	sd_ctrl_write16(host, CTL_SD_XFER_LEN, data->blksz);
-	sd_ctrl_write16(host, CTL_XFER_BLK_COUNT, data->blocks);
+	if (host->mmc->max_blk_count >= SZ_64K)
+		sd_ctrl_write32(host, CTL_XFER_BLK_COUNT, data->blocks);
+	else
+		sd_ctrl_write16(host, CTL_XFER_BLK_COUNT, data->blocks);
 
 	tmio_mmc_start_dma(host, data);
 
author maintainer
#48 lore raw

PATCH 48/52 mmc: sdhci-esdhc-imx: correct the fix of ERR004536

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: BOUGH CHEN <[email protected]>

commit e30be063d6dbcc0f18b1eb25fa709fdef89201fb upstream.

Commit 18094430d6b5 ("mmc: sdhci-esdhc-imx: add ADMA Length Mismatch errata fix") involve the fix of ERR004536, but the fix is incorrect. Double confirm with IC, need to clear the bit 7 of register 0x6c rather than set this bit 7. Here is the definition of bit 7 of 0x6c:
0: enable the new IC fix for ERR004536
1: do not use the IC fix, keep the same as before

Find this issue on i.MX845s-evk board when enable CMDQ, and let system in heavy loading.

root@imx8mmevk:~# dd if=/dev/mmcblk2 of=/dev/null bs=1M &
root@imx8mmevk:~# memtester 1000M > /dev/zero &
root@imx8mmevk:~# [  139.897220] mmc2: cqhci: timeout for tag 16
[  139.901417] mmc2: cqhci: ============ CQHCI REGISTER DUMP ===========
[  139.907862] mmc2: cqhci: Caps:      0x0000310a | Version:  0x00000510
[  139.914311] mmc2: cqhci: Config:    0x00001001 | Control:  0x00000000
[  139.920753] mmc2: cqhci: Int stat:  0x00000000 | Int enab: 0x00000006
[  139.927193] mmc2: cqhci: Int sig:   0x00000006 | Int Coal: 0x00000000
[  139.933634] mmc2: cqhci: TDL base:  0x7809c000 | TDL up32: 0x00000000
[  139.940073] mmc2: cqhci: Doorbell:  0x00030000 | TCN:      0x00000000
[  139.946518] mmc2: cqhci: Dev queue: 0x00010000 | Dev Pend: 0x00010000
[  139.952967] mmc2: cqhci: Task clr:  0x00000000 | SSC1:     0x00011000
[  139.959411] mmc2: cqhci: SSC2:      0x00000001 | DCMD rsp: 0x00000000
[  139.965857] mmc2: cqhci: RED mask:  0xfdf9a080 | TERRI:    0x00000000
[  139.972308] mmc2: cqhci: Resp idx:  0x0000002e | Resp arg: 0x00000900
[  139.978761] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[  139.985214] mmc2: sdhci: Sys addr:  0xb2c19000 | Version:  0x00000002
[  139.991669] mmc2: sdhci: Blk size:  0x00000200 | Blk cnt:  0x00000400
[  139.998127] mmc2: sdhci: Argument:  0x40110400 | Trn mode: 0x00000033
[  140.004618] mmc2: sdhci: Present:   0x01088a8f | Host ctl: 0x00000030
[  140.011113] mmc2: sdhci: Power:     0x00000002 | Blk gap:  0x00000080
[  140.017583] mmc2: sdhci: Wake-up:   0x00000008 | Clock:    0x0000000f
[  140.024039] mmc2: sdhci: Timeout:   0x0000008f | Int stat: 0x00000000
[  140.030497] mmc2: sdhci: Int enab:  0x107f4000 | Sig enab: 0x107f4000
[  140.036972] mmc2: sdhci: AC12 err:  0x00000000 | Slot int: 0x00000502
[  140.043426] mmc2: sdhci: Caps:      0x07eb0000 | Caps_1:   0x8000b407
[  140.049867] mmc2: sdhci: Cmd:       0x00002c1a | Max curr: 0x00ffffff
[  140.056314] mmc2: sdhci: Resp[0]:   0x00000900 | Resp[1]:  0xffffffff
[  140.062755] mmc2: sdhci: Resp[2]:   0x328f5903 | Resp[3]:  0x00d00f00
[  140.069195] mmc2: sdhci: Host ctl2: 0x00000008
[  140.073640] mmc2: sdhci: ADMA Err:  0x00000007 | ADMA Ptr: 0x7809c108
[  140.080079] mmc2: sdhci: ============================================
[  140.086662] mmc2: running CQE recovery
Fixes 18094430d6b5 ("mmc: sdhci-esdhc-imx: add ADMA Length Mismatch errata fix")
---
 drivers/mmc/host/sdhci-esdhc-imx.c |    9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/mmc/host/sdhci-esdhc-imx.c +5 -4
@@ -1077,11 +1077,12 @@ static void sdhci_esdhc_imx_hwinit(struc
 		writel(readl(host->ioaddr + SDHCI_HOST_CONTROL)
 			| ESDHC_BURST_LEN_EN_INCR,
 			host->ioaddr + SDHCI_HOST_CONTROL);
+
 		/*
-		* erratum ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL
-		* TO1.1, it's harmless for MX6SL
-		*/
-		writel(readl(host->ioaddr + 0x6c) | BIT(7),
+		 * erratum ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL
+		 * TO1.1, it's harmless for MX6SL
+		 */
+		writel(readl(host->ioaddr + 0x6c) & ~BIT(7),
 			host->ioaddr + 0x6c);
 
 		/* disable DLL_CTRL delay line settings */
author maintainer
#49 lore raw

PATCH 49/52 mm: enforce min addr even if capable() in expand_downwards()

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jann Horn <[email protected]>

commit 0a1d52994d440e21def1c2174932410b4f2a98a1 upstream.

security_mmap_addr() does a capability check with current_cred(), but we can reach this code from contexts like a VFS write handler where current_cred() must not be used.

This can be abused on systems without SMAP to make NULL pointer dereferences exploitable again.

Fixes 8869477a49c3 ("security: protect from stack expansion into low vm addresses")
---
 mm/mmap.c |    7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)
mm/mmap.c +3 -4
@@ -2348,12 +2348,11 @@ int expand_downwards(struct vm_area_stru
 {
 	struct mm_struct *mm = vma->vm_mm;
 	struct vm_area_struct *prev;
-	int error;
+	int error = 0;
 
 	address &= PAGE_MASK;
-	error = security_mmap_addr(address);
-	if (error)
-		return error;
+	if (address < mmap_min_addr)
+		return -EPERM;
 
 	/* Enforce stack_guard_gap */
 	prev = vma->vm_prev;
author maintainer
#50 lore raw

PATCH 50/52 MIPS: fix truncation in __cmpxchg_small for short values

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Michael Clark <[email protected]>

commit 94ee12b507db8b5876e31c9d6c9d84f556a4b49f upstream.

__cmpxchg_small erroneously uses u8 for load comparison which can be either char or short. This patch changes the local variable to u32 which is sufficiently sized, as the loaded value is already masked and shifted appropriately. Using an integer size avoids any unnecessary canonicalization from use of non native widths.

This patch is part of a series that adapts the MIPS small word atomics code for xchg and cmpxchg on short and char to RISC-V.

Cc RISC-V Patches <[email protected]>
Cc Linux RISC-V <[email protected]>
Cc Linux MIPS <[email protected]>

[[email protected]:
- Fix varialble typo per Jonas Gorski.
- Consolidate load variable with other declarations.]

Fixes 3ba7f44d2b19 ("MIPS: cmpxchg: Implement 1 byte & 2 byte cmpxchg()")
Cc [email protected] # v4.13+
---
 arch/mips/kernel/cmpxchg.c |    3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
arch/mips/kernel/cmpxchg.c +1 -2
@@ -54,10 +54,9 @@ unsigned long __xchg_small(volatile void
 unsigned long __cmpxchg_small(volatile void *ptr, unsigned long old,
 			      unsigned long new, unsigned int size)
 {
-	u32 mask, old32, new32, load32;
+	u32 mask, old32, new32, load32, load;
 	volatile u32 *ptr32;
 	unsigned int shift;
-	u8 load;
 
 	/* Check that ptr is naturally aligned */
 	WARN_ON((unsigned long)ptr & (size - 1));

_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv

author maintainer
#51 lore raw

PATCH 51/52 MIPS: eBPF: Fix icache flush end address

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Paul Burton <[email protected]>

commit d1a2930d8a992fb6ac2529449f81a0056e1b98d1 upstream.

The MIPS eBPF JIT calls flush_icache_range() in order to ensure the icache observes the code that we just wrote. Unfortunately it gets the end address calculation wrong due to some bad pointer arithmetic.

The struct jit_ctx target field is of type pointer to u32, and as such adding one to it will increment the address being pointed to by 4 bytes. Therefore in order to find the address of the end of the code we simply need to add the number of 4 byte instructions emitted, but we mistakenly add the number of instructions multiplied by 4. This results in the call to flush_icache_range() operating on a memory region 4x larger than intended, which is always wasteful and can cause crashes if we overrun into an unmapped page.

Fix this by correcting the pointer arithmetic to remove the bogus multiplication, and use braces to remove the need for a set of brackets whilst also making it obvious that the target field is a pointer.

Fixes b6bd53f9c4e8 ("MIPS: Add missing file for eBPF JIT.")
Cc Alexei Starovoitov <[email protected]>
Cc Daniel Borkmann <[email protected]>
Cc Martin KaFai Lau <[email protected]>
Cc Song Liu <[email protected]>
Cc Yonghong Song <[email protected]>
Cc [email protected] # v4.13+
---
 arch/mips/net/ebpf_jit.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/mips/net/ebpf_jit.c +1 -1
@@ -1971,7 +1971,7 @@ struct bpf_prog *bpf_int_jit_compile(str
 
 	/* Update the icache */
 	flush_icache_range((unsigned long)ctx.target,
-			   (unsigned long)(ctx.target + ctx.idx * sizeof(u32)));
+			   (unsigned long)&ctx.target[ctx.idx]);
 
 	if (bpf_jit_enable > 1)
 		/* Dump JIT code */
author maintainer
#52 lore raw

PATCH 52/52 x86/uaccess: Dont leak the AC flag into __put_user() value evaluation

In reply to Greg Kroah-Hartman

4.14-stable review patch. If anyone has any objections, please let me know.

------------------

From: Andy Lutomirski <[email protected]>

commit 2a418cf3f5f1caf911af288e978d61c9844b0695 upstream.

When calling __put_user(foo(), ptr), the __put_user() macro would call foo() in between __uaccess_begin() and __uaccess_end(). If that code were buggy, then those bugs would be run without SMAP protection.

Fortunately, there seem to be few instances of the problem in the kernel. Nevertheless, __put_user() should be fixed to avoid doing this. Therefore, evaluate __put_user()'s argument before setting AC.

This issue was noticed when an objtool hack by Peter Zijlstra complained about genregs_get() and I compared the assembly output to the C source.

[ bp: Massage commit message and fixed up whitespace. ]

Fixes 11f1a4b9755f ("x86: reorganize SMAP handling in user space accesses")
Cc Peter Zijlstra <[email protected]>
Cc Brian Gerst <[email protected]>
Cc Josh Poimboeuf <[email protected]>
Cc Denys Vlasenko <[email protected]>
---
 arch/x86/include/asm/uaccess.h |    7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
arch/x86/include/asm/uaccess.h +4 -3
@@ -293,8 +293,7 @@ do {									\
 		__put_user_asm(x, ptr, retval, "l", "k", "ir", errret);	\
 		break;							\
 	case 8:								\
-		__put_user_asm_u64((__typeof__(*ptr))(x), ptr, retval,	\
-				   errret);				\
+		__put_user_asm_u64(x, ptr, retval, errret);		\
 		break;							\
 	default:							\
 		__put_user_bad();					\
@@ -440,8 +439,10 @@ do {									\
 #define __put_user_nocheck(x, ptr, size)			\
 ({								\
 	int __pu_err;						\
+	__typeof__(*(ptr)) __pu_val;				\
+	__pu_val = x;						\
 	__uaccess_begin();					\
-	__put_user_size((x), (ptr), (size), __pu_err, -EFAULT);	\
+	__put_user_size(__pu_val, (ptr), (size), __pu_err, -EFAULT);\
 	__uaccess_end();					\
 	__builtin_expect(__pu_err, 0);				\
 })
#53 lore raw
In reply to Greg Kroah-Hartman
Quoted 10 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.14.105 release. There are 52 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Wed Mar 6 08:15:55 UTC 2019. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

Quoted 9 lines
        https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.14.105-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.14.y
and the diffstat can be found below.

thanks,

greg k-h

Results from Linaro’s test farm.
No regressions on arm64, arm, x86_64, and i386.

Summary
------------------------------------------------------------------------

kernel: 4.14.105-rc1
git repo: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
git branch: linux-4.14.y
git commit: b0f58e2dfb7cf26c240d8e0fe6e08b5d11976e22
git describe: v4.14.104-53-gb0f58e2dfb7c
Test details: https://qa-reports.linaro.org/lkft/linux-stable-rc-4.14-oe/build/v4.14.104-53-gb0f58e2dfb7c

No regressions (compared to build v4.14.104)

No fixes (compared to build v4.14.104)

Ran 21829 total tests in the following environments and test suites.

Environments
--------------
- dragonboard-410c - arm64
- hi6220-hikey - arm64
- i386
- juno-r2 - arm64
- qemu_arm
- qemu_arm64
- qemu_i386
- qemu_x86_64
- x15 - arm
- x86_64

Test Suites
-----------
* boot
* install-android-platform-tools-r2600
* kselftest
* libhugetlbfs
* ltp-cap_bounds-tests
* ltp-commands-tests
* ltp-containers-tests
* ltp-cpuhotplug-tests
* ltp-cve-tests
* ltp-fcntl-locktests-tests
* ltp-filecaps-tests
* ltp-fs-tests
* ltp-fs_bind-tests
* ltp-fs_perms_simple-tests
* ltp-fsx-tests
* ltp-hugetlb-tests
* ltp-io-tests
* ltp-ipc-tests
* ltp-math-tests
* ltp-mm-tests
* ltp-nptl-tests
* ltp-pty-tests
* ltp-sched-tests
* ltp-securebits-tests
* ltp-syscalls-tests
* ltp-timers-tests
* spectre-meltdown-checker-test
* ltp-dio-tests
* ltp-open-posix-tests
* kselftest-vsyscall-mode-native
* kselftest-vsyscall-mode-none

Signature · 2 lines
Linaro LKFT
https://lkft.linaro.org
#54 lore raw
In reply to Greg Kroah-Hartman
Quoted 8 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.14.105 release. There are 52 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Wed Mar 6 08:15:55 UTC 2019. Anything received after that time might be too late.

Build results:

	total: 172 pass: 172 fail: 0
Qemu test results:
	total: 328 pass: 328 fail: 0

Guenter

maintainer
#55 lore raw
In reply to Greg Kroah-Hartman
Quoted 9 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.14.105 release. There are 52 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Wed Mar 6 08:15:55 UTC 2019. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

Quoted 8 lines
	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.14.105-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.14.y
and the diffstat can be found below.

thanks,

greg k-h

All tests are passing for Tegra ...

Test results for stable-v4.14:

    8 builds:	8 pass, 0 fail
    16 boots:	16 pass, 0 fail
    20 tests:	20 pass, 0 fail

Linux version: 4.14.105-rc1-gb0f58e2d
Boards tested: tegra124-jetson-tk1, tegra20-ventana,

                tegra210-p2371-2180, tegra30-cardhu-a04

Cheers
Jon

Signature · 1 line
nvpublic
#56 lore raw
In reply to Greg Kroah-Hartman
Quoted 9 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.14.105 release. There are 52 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Wed Mar 6 08:15:55 UTC 2019. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

Quoted 9 lines
	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.14.105-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.14.y
and the diffstat can be found below.

thanks,

greg k-h

Compiled and booted on my test system. No dmesg regressions.

thanks,
-- Shuah