Skip to contentSkip to conversation

arm64: dts: rockchip: fix rk3328 rgmii high tx error rate

PATCH Applied Peter Geis 3 participants 3 messages Mar 13, 2019 – Apr 3, 2019

Subsystems (2)
lore
Share & tools
lore

Peter Geis

author
#0 lore raw

PATCH 1/1 arm64: dts: rockchip: fix rk3328 rgmii high tx error rate

Resubmitting, after further research, review, comments, and suggestions.

Several rk3328 based boards experience high rgmii tx error rates. This is due to several pins in the rk3328.dtsi rgmii pinmux that are missing a defined pull strength setting.
This causes the pinmux driver to default to 2ma (bit mask 00).

These pins are only defined in the rk3328.dtsi, and are not listed in the rk3328 specification.
The TRM only lists them as "Reserved"
(RK3328 TRM V1.1, 3.3.3 Detail Register Description, GRF_GPIO0B_IOMUX, GRF_GPIO0C_IOMUX, GRF_GPIO0D_IOMUX).
However, removal of these pins from the rgmii pinmux definition causes the interface to fail to transmit.

Also, the rgmii tx and rx pins defined in the dtsi are not consistent with the rk3328 specification, with tx pins currently set to 12ma and rx pins set to 2ma.

Fix this by setting tx pins to 8ma and the rx pins to 4ma, consistent with the specification.
Defining the drive strength for the undefined pins eliminated the high tx packet error rate observed under heavy data transfers. Aligning the drive strength to the TRM values eliminated the occasional packet retry errors under iperf3 testing.
This allows much higher data rates with no recorded tx errors.

Tested on the rk3328-roc-cc board.

---
 arch/arm64/boot/dts/rockchip/rk3328.dtsi | 44 ++++++++++++------------
 1 file changed, 22 insertions(+), 22 deletions(-)
arch/arm64/boot/dts/rockchip/rk3328.dtsi +22 -22
index 84f14b132e8f..c55a3f1a87ff 100644
@@ -1642,50 +1642,50 @@
 			rgmiim1_pins: rgmiim1-pins {
 				rockchip,pins =
 					/* mac_txclk */
-					<1 RK_PB4 2 &pcfg_pull_none_12ma>,
+					<1 RK_PB4 2 &pcfg_pull_none_8ma>,
 					/* mac_rxclk */
-					<1 RK_PB5 2 &pcfg_pull_none_2ma>,
+					<1 RK_PB5 2 &pcfg_pull_none_4ma>,
 					/* mac_mdio */
-					<1 RK_PC3 2 &pcfg_pull_none_2ma>,
+					<1 RK_PC3 2 &pcfg_pull_none_4ma>,
 					/* mac_txen */
-					<1 RK_PD1 2 &pcfg_pull_none_12ma>,
+					<1 RK_PD1 2 &pcfg_pull_none_8ma>,
 					/* mac_clk */
-					<1 RK_PC5 2 &pcfg_pull_none_2ma>,
+					<1 RK_PC5 2 &pcfg_pull_none_4ma>,
 					/* mac_rxdv */
-					<1 RK_PC6 2 &pcfg_pull_none_2ma>,
+					<1 RK_PC6 2 &pcfg_pull_none_4ma>,
 					/* mac_mdc */
-					<1 RK_PC7 2 &pcfg_pull_none_2ma>,
+					<1 RK_PC7 2 &pcfg_pull_none_4ma>,
 					/* mac_rxd1 */
-					<1 RK_PB2 2 &pcfg_pull_none_2ma>,
+					<1 RK_PB2 2 &pcfg_pull_none_4ma>,
 					/* mac_rxd0 */
-					<1 RK_PB3 2 &pcfg_pull_none_2ma>,
+					<1 RK_PB3 2 &pcfg_pull_none_4ma>,
 					/* mac_txd1 */
-					<1 RK_PB0 2 &pcfg_pull_none_12ma>,
+					<1 RK_PB0 2 &pcfg_pull_none_8ma>,
 					/* mac_txd0 */
-					<1 RK_PB1 2 &pcfg_pull_none_12ma>,
+					<1 RK_PB1 2 &pcfg_pull_none_8ma>,
 					/* mac_rxd3 */
-					<1 RK_PB6 2 &pcfg_pull_none_2ma>,
+					<1 RK_PB6 2 &pcfg_pull_none_4ma>,
 					/* mac_rxd2 */
-					<1 RK_PB7 2 &pcfg_pull_none_2ma>,
+					<1 RK_PB7 2 &pcfg_pull_none_4ma>,
 					/* mac_txd3 */
-					<1 RK_PC0 2 &pcfg_pull_none_12ma>,
+					<1 RK_PC0 2 &pcfg_pull_none_8ma>,
 					/* mac_txd2 */
-					<1 RK_PC1 2 &pcfg_pull_none_12ma>,
+					<1 RK_PC1 2 &pcfg_pull_none_8ma>,
 
 					/* mac_txclk */
-					<0 RK_PB0 1 &pcfg_pull_none>,
+					<0 RK_PB0 1 &pcfg_pull_none_8ma>,
 					/* mac_txen */
-					<0 RK_PB4 1 &pcfg_pull_none>,
+					<0 RK_PB4 1 &pcfg_pull_none_8ma>,
 					/* mac_clk */
-					<0 RK_PD0 1 &pcfg_pull_none>,
+					<0 RK_PD0 1 &pcfg_pull_none_4ma>,
 					/* mac_txd1 */
-					<0 RK_PC0 1 &pcfg_pull_none>,
+					<0 RK_PC0 1 &pcfg_pull_none_8ma>,
 					/* mac_txd0 */
-					<0 RK_PC1 1 &pcfg_pull_none>,
+					<0 RK_PC1 1 &pcfg_pull_none_8ma>,
 					/* mac_txd3 */
-					<0 RK_PC7 1 &pcfg_pull_none>,
+					<0 RK_PC7 1 &pcfg_pull_none_8ma>,
 					/* mac_txd2 */
-					<0 RK_PC6 1 &pcfg_pull_none>;
+					<0 RK_PC6 1 &pcfg_pull_none_8ma>;
 			};
 
 			rmiim1_pins: rmiim1-pins {
Signature · 1 line
2.20.1
maintainer Applied
#1 lore raw

Am Mittwoch, 13. März 2019, 19:45:36 CET schrieb Peter Geis:

Quoted 27 lines

Resubmitting, after further research, review, comments, and suggestions.

Several rk3328 based boards experience high rgmii tx error rates. This is due to several pins in the rk3328.dtsi rgmii pinmux that are missing a defined pull strength setting.
This causes the pinmux driver to default to 2ma (bit mask 00).

These pins are only defined in the rk3328.dtsi, and are not listed in the rk3328 specification.
The TRM only lists them as "Reserved"
(RK3328 TRM V1.1, 3.3.3 Detail Register Description, GRF_GPIO0B_IOMUX, GRF_GPIO0C_IOMUX, GRF_GPIO0D_IOMUX).
However, removal of these pins from the rgmii pinmux definition causes the interface to fail to transmit.

Also, the rgmii tx and rx pins defined in the dtsi are not consistent with the rk3328 specification, with tx pins currently set to 12ma and rx pins set to 2ma.

Fix this by setting tx pins to 8ma and the rx pins to 4ma, consistent with the specification.
Defining the drive strength for the undefined pins eliminated the high tx packet error rate observed under heavy data transfers. Aligning the drive strength to the TRM values eliminated the occasional packet retry errors under iperf3 testing.
This allows much higher data rates with no recorded tx errors.

Quoted 3 lines

Tested on the rk3328-roc-cc board.

applied as fix for 5.1 after adding Fixes and Cc-stable-tags

Thanks
Heiko

#2 lore raw
Quoted 28 lines · Heiko Stuebner

Am Mittwoch, 13. März 2019, 19:45:36 CET schrieb Peter Geis:

Quoted 27 lines

Resubmitting, after further research, review, comments, and suggestions.

Several rk3328 based boards experience high rgmii tx error rates. This is due to several pins in the rk3328.dtsi rgmii pinmux that are missing a defined pull strength setting.
This causes the pinmux driver to default to 2ma (bit mask 00).

These pins are only defined in the rk3328.dtsi, and are not listed in the rk3328 specification.
The TRM only lists them as "Reserved"
(RK3328 TRM V1.1, 3.3.3 Detail Register Description, GRF_GPIO0B_IOMUX, GRF_GPIO0C_IOMUX, GRF_GPIO0D_IOMUX).
However, removal of these pins from the rgmii pinmux definition causes the interface to fail to transmit.

Also, the rgmii tx and rx pins defined in the dtsi are not consistent with the rk3328 specification, with tx pins currently set to 12ma and rx pins set to 2ma.

Fix this by setting tx pins to 8ma and the rx pins to 4ma, consistent with the specification.
Defining the drive strength for the undefined pins eliminated the high tx packet error rate observed under heavy data transfers. Aligning the drive strength to the TRM values eliminated the occasional packet retry errors under iperf3 testing.
This allows much higher data rates with no recorded tx errors.

Quoted 5 lines
Quoted 3 lines

Tested on the rk3328-roc-cc board.

applied as fix for 5.1 after adding Fixes and Cc-stable-tags

FWIW, whilst looking for something else I think I've actually stumbled across some sort-of-documentation for this mystery pinmux business. Section 22.5 on p560 of the RK3328 TRM seems to describe IOMUX settings that line up with the DT snippets from the BSP kernel even though the GRF section denies them, while Section 22.6.9 on p578 details a wacky arrangement which at least sheds a little light on that curious "third mux setting" and why it implies interaction with the apparently-unconnected internal Tx pads, even if the reasoning behind it remains rather baffling.

Robin.

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel