Skip to contentSkip to conversation

ARM: meson: add p200 and p201 boards

PATCH Superseded Mohammad Rasim 2 participants 7 messages Mar 14, 2019

Subsystems (2)

v2 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v2 cover ARM: meson: add p200 and p201 boards

This adds support for p200 and p201 reference boards from amlogic

Mohammad Rasim (3):
ARM: dts: meson: add p200 and p201 boards
ARM: board: meson: add p201 board
ARM: board: meson: add p200 board

 arch/arm/dts/Makefile               |   2 +
 arch/arm/dts/meson-gxbb-p200.dts    |  99 +++++++++++
 arch/arm/dts/meson-gxbb-p201.dts    |  26 +++
 arch/arm/dts/meson-gxbb-p20x.dtsi   | 247 ++++++++++++++++++++++++++++
 board/amlogic/odroid-c2/README.p200 | 103 ++++++++++++
 board/amlogic/p201/MAINTAINERS      |   6 +
 board/amlogic/p201/Makefile         |   5 +
 board/amlogic/p201/README.p201      | 103 ++++++++++++
 board/amlogic/p201/p201.c           |  43 +++++
 configs/p200_defconfig              |  41 +++++
 configs/p201_defconfig              |  41 +++++
 11 files changed, 716 insertions(+)
 create mode 100644 arch/arm/dts/meson-gxbb-p200.dts
 create mode 100644 arch/arm/dts/meson-gxbb-p201.dts
 create mode 100644 arch/arm/dts/meson-gxbb-p20x.dtsi
 create mode 100644 board/amlogic/odroid-c2/README.p200
 create mode 100644 board/amlogic/p201/MAINTAINERS
 create mode 100644 board/amlogic/p201/Makefile
 create mode 100644 board/amlogic/p201/README.p201
 create mode 100644 board/amlogic/p201/p201.c
 create mode 100644 configs/p200_defconfig
 create mode 100644 configs/p201_defconfig

--
2.21.0

#1 lore raw

PATCH v2 1/3 ARM: dts: meson: add p200 and p201 boards

This adds the device trees for p200 and p201 boards.
Synced from kernel 5.0.0 revision a667cb7a94d48a483fb5d6006fe04a440f1a42ce.

---
 arch/arm/dts/Makefile             |   2 +
 arch/arm/dts/meson-gxbb-p200.dts  |  99 ++++++++++++
 arch/arm/dts/meson-gxbb-p201.dts  |  26 ++++
 arch/arm/dts/meson-gxbb-p20x.dtsi | 247 ++++++++++++++++++++++++++++++
 4 files changed, 374 insertions(+)
 create mode 100644 arch/arm/dts/meson-gxbb-p200.dts
 create mode 100644 arch/arm/dts/meson-gxbb-p201.dts
 create mode 100644 arch/arm/dts/meson-gxbb-p20x.dtsi
arch/arm/dts/Makefile +2 -0
index 2a040b20a5..adf5f26fac 100644
@@ -60,6 +60,8 @@ dtb-$(CONFIG_ARCH_MESON) += \
 	meson-gxbb-nanopi-k2.dtb \
 	meson-gxbb-odroidc2.dtb \
 	meson-gxbb-nanopi-k2.dtb \
+	meson-gxbb-p200.dtb \
+	meson-gxbb-p201.dtb \
 	meson-gxl-s905x-p212.dtb \
 	meson-gxl-s905x-libretech-cc.dtb \
 	meson-gxl-s905x-khadas-vim.dtb \
arch/arm/dts/meson-gxbb-p200.dts new file +99 -0

99 lines not on this page · raw message

arch/arm/dts/meson-gxbb-p201.dts new file +26 -0
new file mode 100644
index 0000000000..56e0dd1ff5
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Andreas Färber
+ * Copyright (c) 2016 BayLibre, Inc.
+ * Author: Kevin Hilman <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "meson-gxbb-p20x.dtsi"
+
+/ {
+	compatible = "amlogic,p201", "amlogic,meson-gxbb";
+	model = "Amlogic Meson GXBB P201 Development Board";
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rmii_pins>;
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+
+	snps,reset-gpio = <&gpio GPIOZ_14 0>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+};
arch/arm/dts/meson-gxbb-p20x.dtsi new file +247 -0

247 lines not on this page · raw message

--
2.21.0

#2 lore raw

PATCH v2 1/3 ARM: dts: meson: add p200 and p201 boards

Hi,

Quoted 2 lines · Mohammad Rasim

This adds the device trees for p200 and p201 boards.
Synced from kernel 5.0.0 revision a667cb7a94d48a483fb5d6006fe04a440f1a42ce.

Commits should be described using the 12bytes identifier, like the Fixes tag. You can update it if you resend, and keep my Acked-by.

Quoted 416 lines
---
 arch/arm/dts/Makefile             |   2 +
 arch/arm/dts/meson-gxbb-p200.dts  |  99 ++++++++++++
 arch/arm/dts/meson-gxbb-p201.dts  |  26 ++++
 arch/arm/dts/meson-gxbb-p20x.dtsi | 247 ++++++++++++++++++++++++++++++
 4 files changed, 374 insertions(+)
 create mode 100644 arch/arm/dts/meson-gxbb-p200.dts
 create mode 100644 arch/arm/dts/meson-gxbb-p201.dts
 create mode 100644 arch/arm/dts/meson-gxbb-p20x.dtsi
arch/arm/dts/Makefile +2 -0
index 2a040b20a5..adf5f26fac 100644
@@ -60,6 +60,8 @@ dtb-$(CONFIG_ARCH_MESON) += \
 	meson-gxbb-nanopi-k2.dtb \
 	meson-gxbb-odroidc2.dtb \
 	meson-gxbb-nanopi-k2.dtb \
+	meson-gxbb-p200.dtb \
+	meson-gxbb-p201.dtb \
 	meson-gxl-s905x-p212.dtb \
 	meson-gxl-s905x-libretech-cc.dtb \
 	meson-gxl-s905x-khadas-vim.dtb \
arch/arm/dts/meson-gxbb-p200.dts new file +99 -0
new file mode 100644
index 0000000000..9d2406a7c4
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Andreas Färber
+ * Copyright (c) 2016 BayLibre, Inc.
+ * Author: Kevin Hilman <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "meson-gxbb-p20x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "amlogic,p200", "amlogic,meson-gxbb";
+	model = "Amlogic Meson GXBB P200 Development Board";
+
+	avdd18_usb_adc: regulator-avdd18_usb_adc {
+		compatible = "regulator-fixed";
+		regulator-name = "AVDD18_USB_ADC";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	adc_keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 0>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+
+		button-home {
+			label = "Home";
+			linux,code = <KEY_HOME>;
+			press-threshold-microvolt = <900000>; /* 50% */
+		};
+
+		button-esc {
+			label = "Esc";
+			linux,code = <KEY_ESC>;
+			press-threshold-microvolt = <684000>; /* 38% */
+		};
+
+		button-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			press-threshold-microvolt = <468000>; /* 26% */
+		};
+
+		button-down {
+			label = "Volume Down";
+			linux,code = <KEY_VOLUMEDOWN>;
+			press-threshold-microvolt = <252000>; /* 14% */
+		};
+
+		button-menu {
+			label = "Menu";
+			linux,code = <KEY_MENU>;
+			press-threshold-microvolt = <0>; /* 0% */
+		};
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rgmii";
+
+	amlogic,tx-delay-ns = <2>;
+
+	snps,reset-gpio = <&gpio GPIOZ_14 0>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy0: ethernet-phy at 3 {
+			/* Micrel KSZ9031 (0x00221620) */
+			reg = <3>;
+			interrupt-parent = <&gpio_intc>;
+			/* MAC_INTR on GPIOZ_15 */
+			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&i2c_B {
+	status = "okay";
+	pinctrl-0 = <&i2c_b_pins>;
+	pinctrl-names = "default";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&avdd18_usb_adc>;
+};
arch/arm/dts/meson-gxbb-p201.dts new file +26 -0
new file mode 100644
index 0000000000..56e0dd1ff5
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Andreas Färber
+ * Copyright (c) 2016 BayLibre, Inc.
+ * Author: Kevin Hilman <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "meson-gxbb-p20x.dtsi"
+
+/ {
+	compatible = "amlogic,p201", "amlogic,meson-gxbb";
+	model = "Amlogic Meson GXBB P201 Development Board";
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rmii_pins>;
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+
+	snps,reset-gpio = <&gpio GPIOZ_14 0>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+};
arch/arm/dts/meson-gxbb-p20x.dtsi new file +247 -1
new file mode 100644
index 0000000000..0be0f2a5d2
@@ -0,0 +1,247 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Andreas Färber
+ * Copyright (c) 2016 BayLibre, Inc.
+ * Author: Kevin Hilman <[email protected]>
+ */
+
+#include "meson-gxbb.dtsi"
+
+/ {
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory at 0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	usb_pwr: regulator-usb-pwrs {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB_PWR";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		/* signal name in schematic: USB_PWR_EN */
+		gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vddio_card: gpio-regulator {
+		compatible = "regulator-gpio";
+
+		regulator-name = "VDDIO_CARD";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+
+		/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
+		states = <1800000 0
+			  3300000 1>;
+
+		regulator-settling-time-up-us = <10000>;
+		regulator-settling-time-down-us = <150000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	cvbs_connector: cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+
+	brcmf: wifi at 1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_card>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* This UART is brought out to the DB9 connector */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0_phy {
+	status = "okay";
+	phy-supply = <&usb_pwr>;
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
--
Quoted 2 lines

2.21.0

Thanks,
Neil

#3 lore raw

PATCH v2 2/3 ARM: board: meson: add p201 board

In reply to Mohammad Rasim
---
 board/amlogic/p201/MAINTAINERS |   6 ++
 board/amlogic/p201/Makefile    |   5 ++
 board/amlogic/p201/README.p201 | 103 +++++++++++++++++++++++++++++++++
 board/amlogic/p201/p201.c      |  43 ++++++++++++++
 configs/p201_defconfig         |  41 +++++++++++++
 5 files changed, 198 insertions(+)
 create mode 100644 board/amlogic/p201/MAINTAINERS
 create mode 100644 board/amlogic/p201/Makefile
 create mode 100644 board/amlogic/p201/README.p201
 create mode 100644 board/amlogic/p201/p201.c
 create mode 100644 configs/p201_defconfig
board/amlogic/p201/MAINTAINERS new file +6 -0
new file mode 100644
index 0000000000..6ebb5f6396
@@ -0,0 +1,6 @@
+P201
+M:	Beniamino Galvani <[email protected]>
+M:	Neil Armstrong <[email protected]>
+S:	Maintained
+F:	board/amlogic/p201/
+F:	configs/p201_defconfig
board/amlogic/p201/Makefile new file +5 -0
new file mode 100644
index 0000000000..11de5396ab
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2016 Beniamino Galvani <[email protected]>
+
+obj-y	:= p201.o
board/amlogic/p201/README.p201 new file +103 -0

103 lines not on this page · raw message

board/amlogic/p201/p201.c new file +43 -0

43 lines not on this page · raw message

configs/p201_defconfig new file +41 -0

41 lines not on this page · raw message

--
2.21.0

#4 lore raw

PATCH v2 2/3 ARM: board: meson: add p201 board

Hi,

Le 14/03/2019 18:00, Mohammad Rasim a écrit :

Quoted 21 lines
---
 board/amlogic/p201/MAINTAINERS |   6 ++
 board/amlogic/p201/Makefile    |   5 ++
 board/amlogic/p201/README.p201 | 103 +++++++++++++++++++++++++++++++++
 board/amlogic/p201/p201.c      |  43 ++++++++++++++
 configs/p201_defconfig         |  41 +++++++++++++
 5 files changed, 198 insertions(+)
 create mode 100644 board/amlogic/p201/MAINTAINERS
 create mode 100644 board/amlogic/p201/Makefile
 create mode 100644 board/amlogic/p201/README.p201
 create mode 100644 board/amlogic/p201/p201.c
 create mode 100644 configs/p201_defconfig
board/amlogic/p201/MAINTAINERS new file +0 -0
new file mode 100644
index 0000000000..6ebb5f6396

board/amlogic/p201/MAINTAINERS line 2

Quoted 2 lines
board/amlogic/p201/MAINTAINERS new file +2 -0
@@ -0,0 +1,6 @@
+P201
+M:	Beniamino Galvani <[email protected]>

You can remove Beniamino for this one.

Quoted 221 lines
board/amlogic/p201/MAINTAINERS new file +4 -0
+M:	Neil Armstrong <[email protected]>
+S:	Maintained
+F:	board/amlogic/p201/
+F:	configs/p201_defconfig
board/amlogic/p201/Makefile new file +5 -0
new file mode 100644
index 0000000000..11de5396ab
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2016 Beniamino Galvani <[email protected]>
+
+obj-y	:= p201.o
board/amlogic/p201/README.p201 new file +103 -0
new file mode 100644
index 0000000000..c251096ce1
@@ -0,0 +1,103 @@
+U-Boot for Amlogic P201
+=======================
+
+P201 is a reference board manufactured by Amlogic with the following
+specifications:
+
+ - Amlogic S905 ARM Cortex-A53 quad-core SoC @ 1.5GHz
+ - ARM Mali 450 GPU
+ - 2GB DDR3 SDRAM
+ - 10/100 Ethernet
+ - HDMI 2.0 4K/60Hz display
+ - 2 x USB 2.0 Host
+ - eMMC, microSD
+ - Infrared receiver
+ - SDIO WiFi Module
+ - CVBS+Stereo Audio Jack
+
+Schematics are available from Amlogic on demand.
+
+Currently the u-boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+ - I2C
+ - Regulators
+ - Reset controller
+ - Clock controller
+ - USB Host
+ - ADC
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make p201_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b n-amlogic-openlinux-20170606 amlogic-u-boot
+ > cd amlogic-u-boot
+ > make gxb_p201_v1_defconfig
+ > make
+ > export FIPDIR=$PWD/fip
+
+Go back to mainline U-boot source tree then :
+ > mkdir fip
+
+ > cp $FIPDIR/gxl/bl2.bin fip/
+ > cp $FIPDIR/gxl/acs.bin fip/
+ > cp $FIPDIR/gxl/bl21.bin fip/
+ > cp $FIPDIR/gxl/bl30.bin fip/
+ > cp $FIPDIR/gxl/bl301.bin fip/
+ > cp $FIPDIR/gxl/bl31.img fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > $FIPDIR/blx_fix.sh \
+	fip/bl30.bin \
+	fip/zero_tmp \
+	fip/bl30_zero.bin \
+	fip/bl301.bin \
+	fip/bl301_zero.bin \
+	fip/bl30_new.bin \
+	bl30
+
+ > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ > $FIPDIR/blx_fix.sh \
+	fip/bl2_acs.bin \
+	fip/zero_tmp \
+	fip/bl2_zero.bin \
+	fip/bl21.bin \
+	fip/bl21_zero.bin \
+	fip/bl2_new.bin \
+	bl2
+
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
+ > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \
+		--output fip/u-boot.bin \
+		--bl2 fip/bl2.n.bin.sig \
+		--bl30 fip/bl30_new.bin.enc \
+		--bl31 fip/bl31.img.enc \
+		--bl33 fip/bl33.bin.enc
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
board/amlogic/p201/p201.c new file +43 -0
new file mode 100644
index 0000000000..ef0c65cd9f
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2016 Beniamino Galvani <[email protected]>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <environment.h>
+#include <asm/io.h>
+#include <asm/arch/gx.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+#include <asm/arch/mem.h>
+
+#define EFUSE_SN_OFFSET		20
+#define EFUSE_SN_SIZE		16
+#define EFUSE_MAC_OFFSET	52
+#define EFUSE_MAC_SIZE		6
+
+int misc_init_r(void)
+{
+	u8 mac_addr[EFUSE_MAC_SIZE];
+	char serial[EFUSE_SN_SIZE];
+	ssize_t len;
+
+	meson_eth_init(PHY_INTERFACE_MODE_RMII, 0);
+
+	if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
+		len = meson_sm_read_efuse(EFUSE_MAC_OFFSET,
+					  mac_addr, EFUSE_MAC_SIZE);
+		if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr))
+			eth_env_set_enetaddr("ethaddr", mac_addr);
+	}
+
+	if (!env_get("serial#")) {
+		len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
+			EFUSE_SN_SIZE);
+		if (len == EFUSE_SN_SIZE)
+			env_set("serial#", serial);
+	}
+
+	return 0;
+}
configs/p201_defconfig new file +41 -1
new file mode 100644
index 0000000000..f6a821cf32
@@ -0,0 +1,41 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_DEBUG_UART_BASE=0xc81004c0
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" p201"
+CONFIG_DEBUG_UART=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_MISC_INIT_R=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-gxbb-p201"
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MESON=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_GXBB=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_SYS_BOARD="p201"
--
Quoted 2 lines

2.21.0

Lookgs good,

#5 lore raw

PATCH v2 3/3 ARM: board: meson: add p200 board

In reply to Mohammad Rasim
---
 board/amlogic/odroid-c2/README.p200 | 103 ++++++++++++++++++++++++++++
 configs/p200_defconfig              |  41 +++++++++++
 2 files changed, 144 insertions(+)
 create mode 100644 board/amlogic/odroid-c2/README.p200
 create mode 100644 configs/p200_defconfig
board/amlogic/odroid-c2/README.p200 new file +103 -0
new file mode 100644
index 0000000000..01d82d1e79
@@ -0,0 +1,103 @@
+U-Boot for Amlogic P200
+=======================
+
+P200 is a reference board manufactured by Amlogic with the following
+specifications:
+
+ - Amlogic S905 ARM Cortex-A53 quad-core SoC @ 1.5GHz
+ - ARM Mali 450 GPU
+ - 2GB DDR3 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.0 4K/60Hz display
+ - 2 x USB 2.0 Host
+ - eMMC, microSD
+ - Infrared receiver
+ - SDIO WiFi Module
+ - CVBS+Stereo Audio Jack
+
+Schematics are available from Amlogic on demand.
+
+Currently the u-boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+ - I2C
+ - Regulators
+ - Reset controller
+ - Clock controller
+ - USB Host
+ - ADC
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make p200_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b n-amlogic-openlinux-20170606 amlogic-u-boot
+ > cd amlogic-u-boot
+ > make gxb_p200_v1_defconfig
+ > make
+ > export FIPDIR=$PWD/fip
+
+Go back to mainline U-boot source tree then :
+ > mkdir fip
+
+ > cp $FIPDIR/gxl/bl2.bin fip/
+ > cp $FIPDIR/gxl/acs.bin fip/
+ > cp $FIPDIR/gxl/bl21.bin fip/
+ > cp $FIPDIR/gxl/bl30.bin fip/
+ > cp $FIPDIR/gxl/bl301.bin fip/
+ > cp $FIPDIR/gxl/bl31.img fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > $FIPDIR/blx_fix.sh \
+	fip/bl30.bin \
+	fip/zero_tmp \
+	fip/bl30_zero.bin \
+	fip/bl301.bin \
+	fip/bl301_zero.bin \
+	fip/bl30_new.bin \
+	bl30
+
+ > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ > $FIPDIR/blx_fix.sh \
+	fip/bl2_acs.bin \
+	fip/zero_tmp \
+	fip/bl2_zero.bin \
+	fip/bl21.bin \
+	fip/bl21_zero.bin \
+	fip/bl2_new.bin \
+	bl2
+
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
+ > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \
+		--output fip/u-boot.bin \
+		--bl2 fip/bl2.n.bin.sig \
+		--bl30 fip/bl30_new.bin.enc \
+		--bl31 fip/bl31.img.enc \
+		--bl33 fip/bl33.bin.enc
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
configs/p200_defconfig new file +41 -0

41 lines not on this page · raw message

--
2.21.0

#6 lore raw

PATCH v2 3/3 ARM: board: meson: add p200 board

Hi,

Le 14/03/2019 18:00, Mohammad Rasim a écrit :

Quoted 8 lines
---
 board/amlogic/odroid-c2/README.p200 | 103 ++++++++++++++++++++++++++++
 configs/p200_defconfig              |  41 +++++++++++
 2 files changed, 144 insertions(+)
 create mode 100644 board/amlogic/odroid-c2/README.p200
 create mode 100644 configs/p200_defconfig

You should also update the MAINTAINERS file in board/amlogic/odroid-c2/ for configs/p200_defconfig

Otherwise looks good

Neil

Quoted 160 lines
board/amlogic/odroid-c2/README.p200 new file +103 -0
new file mode 100644
index 0000000000..01d82d1e79
@@ -0,0 +1,103 @@
+U-Boot for Amlogic P200
+=======================
+
+P200 is a reference board manufactured by Amlogic with the following
+specifications:
+
+ - Amlogic S905 ARM Cortex-A53 quad-core SoC @ 1.5GHz
+ - ARM Mali 450 GPU
+ - 2GB DDR3 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.0 4K/60Hz display
+ - 2 x USB 2.0 Host
+ - eMMC, microSD
+ - Infrared receiver
+ - SDIO WiFi Module
+ - CVBS+Stereo Audio Jack
+
+Schematics are available from Amlogic on demand.
+
+Currently the u-boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+ - I2C
+ - Regulators
+ - Reset controller
+ - Clock controller
+ - USB Host
+ - ADC
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make p200_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b n-amlogic-openlinux-20170606 amlogic-u-boot
+ > cd amlogic-u-boot
+ > make gxb_p200_v1_defconfig
+ > make
+ > export FIPDIR=$PWD/fip
+
+Go back to mainline U-boot source tree then :
+ > mkdir fip
+
+ > cp $FIPDIR/gxl/bl2.bin fip/
+ > cp $FIPDIR/gxl/acs.bin fip/
+ > cp $FIPDIR/gxl/bl21.bin fip/
+ > cp $FIPDIR/gxl/bl30.bin fip/
+ > cp $FIPDIR/gxl/bl301.bin fip/
+ > cp $FIPDIR/gxl/bl31.img fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > $FIPDIR/blx_fix.sh \
+	fip/bl30.bin \
+	fip/zero_tmp \
+	fip/bl30_zero.bin \
+	fip/bl301.bin \
+	fip/bl301_zero.bin \
+	fip/bl30_new.bin \
+	bl30
+
+ > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ > $FIPDIR/blx_fix.sh \
+	fip/bl2_acs.bin \
+	fip/zero_tmp \
+	fip/bl2_zero.bin \
+	fip/bl21.bin \
+	fip/bl21_zero.bin \
+	fip/bl2_new.bin \
+	bl2
+
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
+ > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \
+		--output fip/u-boot.bin \
+		--bl2 fip/bl2.n.bin.sig \
+		--bl30 fip/bl30_new.bin.enc \
+		--bl31 fip/bl31.img.enc \
+		--bl33 fip/bl33.bin.enc
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
configs/p200_defconfig new file +41 -1
new file mode 100644
index 0000000000..4011866140
@@ -0,0 +1,41 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_DEBUG_UART_BASE=0xc81004c0
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" p200"
+CONFIG_DEBUG_UART=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_MISC_INIT_R=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-gxbb-p200"
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MESON=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_GXBB=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_SYS_BOARD="odroid-c2"
--

2.21.0