Skip to contentSkip to conversation

package/ecryptfs-utils: Add support without gettext

PATCH New Vadim Kochan 3 participants 6 messages Mar 15, 2019 – Mar 26, 2019

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 package/ecryptfs-utils: Add support without gettext

Add custom ecryptfs-common script which provides gettext wrapper as function, script checks if there is gettext tool, if no - the "printf" will be used instead. Each script which uses gettext is patched with including this ecryptfs-common script.

gettext package is now selected automatically only if NLS is enabled.

Also replaced AM_GLIB_GNU_GETTEXT by AM_GNU_GETTEXT because original macro is removed during autoreconf. Actually AM_GLIB_GNU_GETTEXT is marked as deprecated in:

https://gitlab.gnome.org/GNOME/glib/blob/master/m4macros/glib-gettext.m4#L437

so it is ok to use the gettext's one.

---

v2:
1) Move ecryptfs-common from package/ecryptfs-utils to *.patch and install it from src/utils/Makefile.am

2) Use solution from Yann E. Morin for gettext-wrapper

3) Replace AM_GLIB_GNU_GETTEXT by AM_GNU_GETTEXT

4) Use @prefix@ and @PACKAGE@ variables to properly include the ecryptfs-common script in utils which uses gettext, it requires to add these utils scripts into configure.ac AC_CONFIG_FILES for variable replacement.

 ...tils-Use-printf-if-gettext-does-not-exist.patch | 217 +++++++++++++++++++++
 package/ecryptfs-utils/Config.in                   |   2 +-
 package/ecryptfs-utils/ecryptfs-utils.mk           |   5 +
 3 files changed, 223 insertions(+), 1 deletion(-)
 create mode 100644 package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +217 -0
new file mode 100644
index 0000000000..7fe8756323
@@ -0,0 +1,217 @@
+From e2a69d509653ff189dd8dd7ed30ff568a0183f1a Mon Sep 17 00:00:00 2001
+From: Vadim Kochan <[email protected]>
+Date: Tue, 12 Mar 2019 02:15:33 +0200
+Subject: [PATCH] utils: Use "printf" if gettext does not exist
+
+There might be a case when gettext does not exist on the system,
+so use just "printf" instead. Added gettext wrapper which imitates
+gettext behaviour, wrapper is used only if gettext is not found
+by "which". ecryptfs-common is included by each script which uses
+gettext tool.
+
+AM_GLIB_GNU_GETTEXT is replaced by AM_GNU_GETTEXT, to get rid of
+glib2 dependency just only for this macro. Actually this macro is marked
+as deprecated in:
+
+    https://gitlab.gnome.org/GNOME/glib/blob/master/m4macros/glib-gettext.m4#L437
+
+Signed-off-by: Vadim Kochan <[email protected]>
+---
+ configure.ac                      | 12 ++++++++++--
+ src/utils/Makefile.am             |  4 +++-
+ src/utils/ecryptfs-common         | 30 ++++++++++++++++++++++++++++++
+ src/utils/ecryptfs-migrate-home   |  2 ++
+ src/utils/ecryptfs-mount-private  |  2 ++
+ src/utils/ecryptfs-rewrite-file   |  2 ++
+ src/utils/ecryptfs-setup-private  |  3 +++
+ src/utils/ecryptfs-setup-swap     |  2 ++
+ src/utils/ecryptfs-umount-private |  2 ++
+ src/utils/ecryptfs-verify         |  2 ++
+ 10 files changed, 58 insertions(+), 3 deletions(-)
+ create mode 100755 src/utils/ecryptfs-common
+
+diff --git a/configure.ac b/configure.ac
+index bbc6ffc..eec1ebc 100644
+--- a/configure.ac
++++ b/configure.ac
+@@ -13,7 +13,7 @@ AC_PREREQ(2.59)
+ AC_INIT([ecryptfs-utils],[111])
+ AC_CANONICAL_HOST
+ AC_CANONICAL_TARGET
+-AM_INIT_AUTOMAKE([${PACKAGE_NAME}], [${PACKAGE_VERSION}])
++AM_INIT_AUTOMAKE([foreign])
+ AC_CONFIG_SRCDIR([src/libecryptfs])
+ AC_CONFIG_HEADERS([config.h])
+ AC_SUBST(AM_CPPFLAGS, '-include $(top_builddir)/config.h')
+@@ -369,7 +369,8 @@ AC_SUBST(GETTEXT_PACKAGE)
+ AC_DEFINE_UNQUOTED(GETTEXT_PACKAGE,"$GETTEXT_PACKAGE",
+                    [the gettext translation domain])
+ 
+-AM_GLIB_GNU_GETTEXT
++AM_GNU_GETTEXT_VERSION([0.19])
++AM_GNU_GETTEXT([external])
+ 
+ IT_PROG_INTLTOOL([0.41.0])
+ 
+@@ -439,6 +440,13 @@ AC_CONFIG_FILES([
+ 	tests/kernel/Makefile
+ 	tests/userspace/Makefile
+ 	po/Makefile.in
++	src/utils/ecryptfs-migrate-home:src/utils/ecryptfs-migrate-home
++	src/utils/ecryptfs-mount-private:src/utils/ecryptfs-mount-private
++	src/utils/ecryptfs-rewrite-file:src/utils/ecryptfs-rewrite-file
++	src/utils/ecryptfs-setup-private:src/utils/ecryptfs-setup-private
++	src/utils/ecryptfs-setup-swap:src/utils/ecryptfs-setup-swap
++	src/utils/ecryptfs-umount-private:src/utils/ecryptfs-umount-private
++	src/utils/ecryptfs-verify:src/utils/ecryptfs-verify
+ ])
+ AC_OUTPUT
+ 
+diff --git a/src/utils/Makefile.am b/src/utils/Makefile.am
+index 83cf851..54c3bdc 100644
+--- a/src/utils/Makefile.am
++++ b/src/utils/Makefile.am
+@@ -21,9 +21,11 @@ bin_SCRIPTS = ecryptfs-setup-private \
+ 	      ecryptfs-find \
+ 	      ecryptfs-verify
+ bin2dir = $(bindir)
+-
+ noinst_PROGRAMS=test
+ 
++commonlibdir=$(libdir)/ecryptfs-utils
++commonlib_SCRIPTS=ecryptfs-common
++
+ if ENABLE_TESTS
+ TESTS=test
+ endif
+diff --git a/src/utils/ecryptfs-common b/src/utils/ecryptfs-common
+new file mode 100755
+index 0000000..3b18568
+--- /dev/null
++++ b/src/utils/ecryptfs-common
+@@ -0,0 +1,30 @@
++# Thanks to "Yann E. MORIN" <[email protected]>
++# for this gettext replacement function
++if ! which gettext >/dev/null 2>&1; then
++gettext() {
++    if [ -n "${GETTEXT}" ]; then
++	# Weird construct so that script that are 'set -e'
++	# fail at the call site of gettext and not here.
++	"${GETTEXT}" "${@}" || return $?
++	return 0
++    fi
++    while [ ${#} -ne 0 ]; do
++	case "${1}" in
++	  (-h)              printf "no help\n"; return 0;;
++	  (-V)              printf "0.0.0\n"; return 0;;
++	  (-d|--domain)     shift 2;;
++	  (-d*|--domain=*)  shift 1;;
++	  (-e|-E|-n)        shift 1;;
++	  (-s)              shift 1;;  # Ignore?
++	  (-*)              printf "invalid option '%s'\n" "${1}" >&2; return 1;;
++	  (*)               break;;
++	esac
++    done
++    case ${#} in
++      (0)   printf "missing arguments\n" >&2; return 1;;
++      (1)   printf "%s" "${1}";;
++      (2)   shift; printf "%s" "${2}";;
++      (*)   printf "too many arguments\n" >&2; return 1;;
++    esac
++}
++fi
+diff --git a/src/utils/ecryptfs-migrate-home b/src/utils/ecryptfs-migrate-home
+index b810146..1233910 100755
+--- a/src/utils/ecryptfs-migrate-home
++++ b/src/utils/ecryptfs-migrate-home
+@@ -24,6 +24,8 @@
+ 
+ set -e
+ 
++. @prefix@/lib/@PACKAGE@/ecryptfs-common
++
+ PRIVATE_DIR="Private"
+ 
+ usage() {
+diff --git a/src/utils/ecryptfs-mount-private b/src/utils/ecryptfs-mount-private
+index c32708f..218d0a2 100755
+--- a/src/utils/ecryptfs-mount-private
++++ b/src/utils/ecryptfs-mount-private
+@@ -12,6 +12,8 @@
+ #  * inserts the mount passphrase into the keyring
+ #  * and mounts a user's encrypted private folder
+ 
++. @prefix@/lib/@PACKAGE@/ecryptfs-common
++
+ PRIVATE_DIR="Private"
+ WRAPPING_PASS="LOGIN"
+ PW_ATTEMPTS=3
+diff --git a/src/utils/ecryptfs-rewrite-file b/src/utils/ecryptfs-rewrite-file
+index c4f67f5..6b00370 100755
+--- a/src/utils/ecryptfs-rewrite-file
++++ b/src/utils/ecryptfs-rewrite-file
+@@ -17,6 +17,8 @@
+ #    You should have received a copy of the GNU General Public License
+ #    along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ 
++. @prefix@/lib/@PACKAGE@/ecryptfs-common
++
+ TEXTDOMAIN="ecryptfs-utils"
+ 
+ error() {
+diff --git a/src/utils/ecryptfs-setup-private b/src/utils/ecryptfs-setup-private
+index e90d1d0..50073d4 100755
+--- a/src/utils/ecryptfs-setup-private
++++ b/src/utils/ecryptfs-setup-private
+@@ -6,6 +6,9 @@
+ # Ported for use on Ubuntu by Dustin Kirkland <[email protected]>
+ # Copyright (C) 2008 Canonical Ltd.
+ # Copyright (C) 2007-2008 International Business Machines
++
++. @prefix@/lib/@PACKAGE@/ecryptfs-common
++
+ PRIVATE_DIR="Private"
+ WRAPPING_PASS="LOGIN"
+ ECRYPTFS_DIR="/home/.ecryptfs"
+diff --git a/src/utils/ecryptfs-setup-swap b/src/utils/ecryptfs-setup-swap
+index 41cf18a..f122674 100755
+--- a/src/utils/ecryptfs-setup-swap
++++ b/src/utils/ecryptfs-setup-swap
+@@ -19,6 +19,8 @@
+ # The cryptswap setup used here follows a guide published at:
+ #  * http://ubuntumagnet.com/2007/11/creating-encrypted-swap-file-ubuntu-using-cryptsetup
+ 
++. @prefix@/lib/@PACKAGE@/ecryptfs-common
++
+ TEXTDOMAIN="ecryptfs-utils"
+ 
+ error() {
+diff --git a/src/utils/ecryptfs-umount-private b/src/utils/ecryptfs-umount-private
+index 27edeaa..5645f4d 100755
+--- a/src/utils/ecryptfs-umount-private
++++ b/src/utils/ecryptfs-umount-private
+@@ -5,6 +5,8 @@
+ # Original by Michael Halcrow, IBM
+ # Extracted to a stand-alone script by Dustin Kirkland <[email protected]>
+ 
++. @prefix@/lib/@PACKAGE@/ecryptfs-common
++
+ TEXTDOMAIN="ecryptfs-utils"
+ 
+ if grep -qs "$HOME/.Private $PWD ecryptfs " /proc/mounts 2>/dev/null; then
+diff --git a/src/utils/ecryptfs-verify b/src/utils/ecryptfs-verify
+index b55641d..f102d2b 100755
+--- a/src/utils/ecryptfs-verify
++++ b/src/utils/ecryptfs-verify
+@@ -16,6 +16,8 @@
+ #    You should have received a copy of the GNU General Public License
+ #    along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ 
++. @prefix@/lib/@PACKAGE@/ecryptfs-common
++
+ error() {
+ 	echo `gettext "ERROR:"` "$@" 1>&2
+ 	echo `gettext "ERROR:"` "Configuration invalid" 1>&2
+-- 
+2.14.1
+
package/ecryptfs-utils/Config.in +1 -1
index 6652d33e0e..1438c1754c 100644
@@ -12,7 +12,7 @@ config BR2_PACKAGE_ECRYPTFS_UTILS
 	select BR2_PACKAGE_LIBNSS
 	# runtime dependency only, some scripts are using the
 	# 'gettext' program to get translations
-	select BR2_PACKAGE_GETTEXT
+	select BR2_PACKAGE_GETTEXT if BR2_SYSTEM_ENABLE_NLS
 	# runtime dependency only
 	select BR2_PACKAGE_GETENT
 	help
package/ecryptfs-utils/ecryptfs-utils.mk +5 -0
index eb3194b6d0..1b49397137 100644
@@ -25,4 +25,9 @@ else
 ECRYPTFS_UTILS_CONF_OPTS += --disable-openssl
 endif
 
+define ECRYPTFS_UTILS_RUN_AUTOGEN
+	cd $(@D) && PATH=$(BR_PATH) ./autogen.sh
+endef
+ECRYPTFS_UTILS_PRE_CONFIGURE_HOOKS += ECRYPTFS_UTILS_RUN_AUTOGEN
+
 $(eval $(autotools-package))
Signature · 1 line
2.14.1
#1 lore raw

PATCH v2 1/1 package/ecryptfs-utils: Add support without gettext

Vadim, All,

On 2019-03-15 04:34 +0200, Vadim Kochan spake thusly:

Quoted 7 lines

Add custom ecryptfs-common script which provides gettext wrapper as function, script checks if there is gettext tool, if no - the "printf" will be used instead. Each script which uses gettext is patched with including this ecryptfs-common script.

gettext package is now selected automatically only if NLS is enabled.

Quoted 7 lines

Also replaced AM_GLIB_GNU_GETTEXT by AM_GNU_GETTEXT because original macro is removed during autoreconf. Actually AM_GLIB_GNU_GETTEXT is marked as deprecated in:

https://gitlab.gnome.org/GNOME/glib/blob/master/m4macros/glib-gettext.m4#L437

so it is ok to use the gettext's one.

I know you've pourred quite some effort into this solution, but I am still not entirely convinced.

So, my position on how we should handle this in Buildroot is as follows:

1. When the real 'gettext' utility is not available (for whatever reason), then we should install our own, fake gettext, like the one I previously suggested.

2. If you are really interested, push a change upstream that makes ecryptfs-utils not require gettext, but with a solution that does not use a wrapper. see below for more on that.

3. If/when upstream supports running without a gettext utility, then we can either bump the version in Buildroot, or backport the patches.

Now, for (1), what package should be responsible for providing the fake gettext is not clear-cut. gettext-tiny would look like a good candidate, though.

For (2), see below...

Quoted 1 line

[--SNIP--]

package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch line 4

Quoted 10 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +4 -0
new file mode 100644
index 0000000000..7fe8756323
@@ -0,0 +1,217 @@
+From e2a69d509653ff189dd8dd7ed30ff568a0183f1a Mon Sep 17 00:00:00 2001
+From: Vadim Kochan <[email protected]>
+Date: Tue, 12 Mar 2019 02:15:33 +0200
+Subject: [PATCH] utils: Use "printf" if gettext does not exist

You should definitely send this upstream.

package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch line 10

Quoted 5 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +5 -0
+There might be a case when gettext does not exist on the system,
+so use just "printf" instead. Added gettext wrapper which imitates
+gettext behaviour, wrapper is used only if gettext is not found
+by "which". ecryptfs-common is included by each script which uses
+gettext tool.

I think upstream will want a solution that does not require a fake wrapper that really mimicks the reall gettext entirely, this their use of it is entirely confined to their scripts, and they always call it with just the message to display.

In this case, the wrapper-function would probably be just as easy as:

    # This is in ${libdir}/ecryptfs-utils/sh-functions
    if ! which gettext >/dev/null 2>&1; then
        gettext() {
            if [ -n "${GETTEXT}" ]; then
                "${GETTEXT}" "${@}"
            else
                printf "%s" "${*}"
            fi || return $?  # Trick for 'set -e' to fail at call-site, not here
        }
    fi

and be done with it.

package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch line 16

Quoted 5 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +5 -0
+AM_GLIB_GNU_GETTEXT is replaced by AM_GNU_GETTEXT, to get rid of
+glib2 dependency just only for this macro. Actually this macro is marked
+as deprecated in:
+
+    https://gitlab.gnome.org/GNOME/glib/blob/master/m4macros/glib-gettext.m4#L437

So, when you send this upstream, you should probably split it up in different patches:

1. fix for the call to AM_INIT_AUTOMAKE()
2. change from AM_GLIB_GNU_GETTEXT() to AM_GNU_GETTEXT()
3. Convert of scripts to use the gettext wrapper-function

Quoted 39 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +39 -0
+Signed-off-by: Vadim Kochan <[email protected]>
+---
+ configure.ac                      | 12 ++++++++++--
+ src/utils/Makefile.am             |  4 +++-
+ src/utils/ecryptfs-common         | 30 ++++++++++++++++++++++++++++++
+ src/utils/ecryptfs-migrate-home   |  2 ++
+ src/utils/ecryptfs-mount-private  |  2 ++
+ src/utils/ecryptfs-rewrite-file   |  2 ++
+ src/utils/ecryptfs-setup-private  |  3 +++
+ src/utils/ecryptfs-setup-swap     |  2 ++
+ src/utils/ecryptfs-umount-private |  2 ++
+ src/utils/ecryptfs-verify         |  2 ++
+ 10 files changed, 58 insertions(+), 3 deletions(-)
+ create mode 100755 src/utils/ecryptfs-common
+
+diff --git a/configure.ac b/configure.ac
+index bbc6ffc..eec1ebc 100644
+--- a/configure.ac
++++ b/configure.ac
+@@ -13,7 +13,7 @@ AC_PREREQ(2.59)
+ AC_INIT([ecryptfs-utils],[111])
+ AC_CANONICAL_HOST
+ AC_CANONICAL_TARGET
+-AM_INIT_AUTOMAKE([${PACKAGE_NAME}], [${PACKAGE_VERSION}])
++AM_INIT_AUTOMAKE([foreign])
+ AC_CONFIG_SRCDIR([src/libecryptfs])
+ AC_CONFIG_HEADERS([config.h])
+ AC_SUBST(AM_CPPFLAGS, '-include $(top_builddir)/config.h')
+@@ -369,7 +369,8 @@ AC_SUBST(GETTEXT_PACKAGE)
+ AC_DEFINE_UNQUOTED(GETTEXT_PACKAGE,"$GETTEXT_PACKAGE",
+                    [the gettext translation domain])
+ 
+-AM_GLIB_GNU_GETTEXT
++AM_GNU_GETTEXT_VERSION([0.19])
++AM_GNU_GETTEXT([external])
+ 
+ IT_PROG_INTLTOOL([0.41.0])
+ 
+@@ -439,6 +440,13 @@ AC_CONFIG_FILES([

package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch line 66

Quoted 10 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +10 -0
+ 	tests/kernel/Makefile
+ 	tests/userspace/Makefile
+ 	po/Makefile.in
++	src/utils/ecryptfs-migrate-home:src/utils/ecryptfs-migrate-home
++	src/utils/ecryptfs-mount-private:src/utils/ecryptfs-mount-private
++	src/utils/ecryptfs-rewrite-file:src/utils/ecryptfs-rewrite-file
++	src/utils/ecryptfs-setup-private:src/utils/ecryptfs-setup-private
++	src/utils/ecryptfs-setup-swap:src/utils/ecryptfs-setup-swap
++	src/utils/ecryptfs-umount-private:src/utils/ecryptfs-umount-private
++	src/utils/ecryptfs-verify:src/utils/ecryptfs-verify

Since those will now undergo pattern substitution, they should be renamed with a .in extension.

Also, it is usualy bad practice to generate such scripts from configure. Instead, they should be generated in Makefile.am as new targets. Yes, this is a bit more involved, but is much cleaner: when you change such a script, you just have to run 'make' again, rather than re-run configure.

package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch line 82

Quoted 2 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +2 -0
++commonlibdir=$(libdir)/ecryptfs-utils
++commonlib_SCRIPTS=ecryptfs-common

I think 'sh-functions' is more appropriate.

Regards,
Yann E. MORIN.

Signature · 6 lines
.-----------------.--------------------.------------------.--------------------.
|  Yann E. MORIN  | Real-Time Embedded | /"\ ASCII RIBBON | Erics' conspiracy: |
| +33 662 376 056 | Software  Designer | \ / CAMPAIGN     |  ___               |
| +33 561 099 427 `------------.-------:  X  AGAINST      |  \e/  There is no  |
| http://ymorin.is-a-geek.org/ | _/*\_ | / \ HTML MAIL    |   v   conspiracy.  |
'------------------------------^-------^------------------^--------------------'
#2 lore raw

PATCH v2 1/1 package/ecryptfs-utils: Add support without gettext

Quoted 4 lines · Yann E. MORIN

Also, it is usualy bad practice to generate such scripts from configure. Instead, they should be generated in Makefile.am as new targets. Yes, this is a bit more involved, but is much cleaner: when you change such a script, you just have to run 'make' again, rather than re-run configure.

Is that really so? I thought automake would generate a rule that just re-runs
config.status when such a file changes. Haven't tested though.

Regards,
Arnout

#3 lore raw

PATCH v2 1/1 package/ecryptfs-utils: Add support without gettext

Arnout, All,

On 2019-03-26 21:49 +0100, Arnout Vandecappelle spake thusly:

Quoted 8 lines · Yann E. MORIN
Quoted 4 lines

Also, it is usualy bad practice to generate such scripts from configure. Instead, they should be generated in Makefile.am as new targets. Yes, this is a bit more involved, but is much cleaner: when you change such a script, you just have to run 'make' again, rather than re-run configure.

Is that really so? I thought automake would generate a rule that just re-runs
config.status when such a file changes. Haven't tested though.

Hmm.. Maybe. It's been a while I wrote my last autotool package.

In any case, I still remember that it's good practice to only generate from ./configure things that are needed to do the actual build, and that anything not needed to run 'make' should be handled in Makefile.am.

(pushing the comparison to the limits: if they were C files, you'd compile them from Makefile.am, not configure).

Regards,
Yann E. MORIN.

Signature · 6 lines
.-----------------.--------------------.------------------.--------------------.
|  Yann E. MORIN  | Real-Time Embedded | /"\ ASCII RIBBON | Erics' conspiracy: |
| +33 662 376 056 | Software  Designer | \ / CAMPAIGN     |  ___               |
| +33 561 099 427 `------------.-------:  X  AGAINST      |  \e/  There is no  |
| http://ymorin.is-a-geek.org/ | _/*\_ | / \ HTML MAIL    |   v   conspiracy.  |
'------------------------------^-------^------------------^--------------------'
#4 lore raw

PATCH v2 1/1 package/ecryptfs-utils: Add support without gettext

In reply to Yann E. MORIN

Hi Yann,

Quoted 148 lines · Yann E. MORIN

Vadim, All,

On 2019-03-15 04:34 +0200, Vadim Kochan spake thusly:

Quoted 7 lines

Add custom ecryptfs-common script which provides gettext wrapper as function, script checks if there is gettext tool, if no - the "printf" will be used instead. Each script which uses gettext is patched with including this ecryptfs-common script.

gettext package is now selected automatically only if NLS is enabled.

Quoted 7 lines

Also replaced AM_GLIB_GNU_GETTEXT by AM_GNU_GETTEXT because original macro is removed during autoreconf. Actually AM_GLIB_GNU_GETTEXT is marked as deprecated in:

https://gitlab.gnome.org/GNOME/glib/blob/master/m4macros/glib-gettext.m4#L437

so it is ok to use the gettext's one.

I know you've pourred quite some effort into this solution, but I am still not entirely convinced.

So, my position on how we should handle this in Buildroot is as follows:

1. When the real 'gettext' utility is not available (for whatever reason), then we should install our own, fake gettext, like the one I previously suggested.

2. If you are really interested, push a change upstream that makes ecryptfs-utils not require gettext, but with a solution that does not use a wrapper. see below for more on that.

3. If/when upstream supports running without a gettext utility, then we can either bump the version in Buildroot, or backport the patches.

Now, for (1), what package should be responsible for providing the fake gettext is not clear-cut. gettext-tiny would look like a good candidate, though.

For (2), see below...

Quoted 1 line

[--SNIP--]

package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch line 4

Quoted 10 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +4 -0
new file mode 100644
index 0000000000..7fe8756323
@@ -0,0 +1,217 @@
+From e2a69d509653ff189dd8dd7ed30ff568a0183f1a Mon Sep 17 00:00:00 2001
+From: Vadim Kochan <[email protected]>
+Date: Tue, 12 Mar 2019 02:15:33 +0200
+Subject: [PATCH] utils: Use "printf" if gettext does not exist

You should definitely send this upstream.

package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch line 10

Quoted 5 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +5 -0
+There might be a case when gettext does not exist on the system,
+so use just "printf" instead. Added gettext wrapper which imitates
+gettext behaviour, wrapper is used only if gettext is not found
+by "which". ecryptfs-common is included by each script which uses
+gettext tool.

I think upstream will want a solution that does not require a fake wrapper that really mimicks the reall gettext entirely, this their use of it is entirely confined to their scripts, and they always call it with just the message to display.

In this case, the wrapper-function would probably be just as easy as:

    # This is in ${libdir}/ecryptfs-utils/sh-functions
    if ! which gettext >/dev/null 2>&1; then
        gettext() {
            if [ -n "${GETTEXT}" ]; then
                "${GETTEXT}" "${@}"
            else
                printf "%s" "${*}"
            fi || return $?  # Trick for 'set -e' to fail at call-site, not here
        }
    fi

and be done with it.

package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch line 16

Quoted 5 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +5 -0
+AM_GLIB_GNU_GETTEXT is replaced by AM_GNU_GETTEXT, to get rid of
+glib2 dependency just only for this macro. Actually this macro is marked
+as deprecated in:
+
+    https://gitlab.gnome.org/GNOME/glib/blob/master/m4macros/glib-gettext.m4#L437

So, when you send this upstream, you should probably split it up in different patches:

1. fix for the call to AM_INIT_AUTOMAKE()
2. change from AM_GLIB_GNU_GETTEXT() to AM_GNU_GETTEXT()
3. Convert of scripts to use the gettext wrapper-function

Quoted 39 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +39 -0
+Signed-off-by: Vadim Kochan <[email protected]>
+---
+ configure.ac                      | 12 ++++++++++--
+ src/utils/Makefile.am             |  4 +++-
+ src/utils/ecryptfs-common         | 30 ++++++++++++++++++++++++++++++
+ src/utils/ecryptfs-migrate-home   |  2 ++
+ src/utils/ecryptfs-mount-private  |  2 ++
+ src/utils/ecryptfs-rewrite-file   |  2 ++
+ src/utils/ecryptfs-setup-private  |  3 +++
+ src/utils/ecryptfs-setup-swap     |  2 ++
+ src/utils/ecryptfs-umount-private |  2 ++
+ src/utils/ecryptfs-verify         |  2 ++
+ 10 files changed, 58 insertions(+), 3 deletions(-)
+ create mode 100755 src/utils/ecryptfs-common
+
+diff --git a/configure.ac b/configure.ac
+index bbc6ffc..eec1ebc 100644
+--- a/configure.ac
++++ b/configure.ac
+@@ -13,7 +13,7 @@ AC_PREREQ(2.59)
+ AC_INIT([ecryptfs-utils],[111])
+ AC_CANONICAL_HOST
+ AC_CANONICAL_TARGET
+-AM_INIT_AUTOMAKE([${PACKAGE_NAME}], [${PACKAGE_VERSION}])
++AM_INIT_AUTOMAKE([foreign])
+ AC_CONFIG_SRCDIR([src/libecryptfs])
+ AC_CONFIG_HEADERS([config.h])
+ AC_SUBST(AM_CPPFLAGS, '-include $(top_builddir)/config.h')
+@@ -369,7 +369,8 @@ AC_SUBST(GETTEXT_PACKAGE)
+ AC_DEFINE_UNQUOTED(GETTEXT_PACKAGE,"$GETTEXT_PACKAGE",
+                    [the gettext translation domain])
+ 
+-AM_GLIB_GNU_GETTEXT
++AM_GNU_GETTEXT_VERSION([0.19])
++AM_GNU_GETTEXT([external])
+ 
+ IT_PROG_INTLTOOL([0.41.0])
+ 
+@@ -439,6 +440,13 @@ AC_CONFIG_FILES([

package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch line 66

Quoted 10 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +10 -0
+ 	tests/kernel/Makefile
+ 	tests/userspace/Makefile
+ 	po/Makefile.in
++	src/utils/ecryptfs-migrate-home:src/utils/ecryptfs-migrate-home
++	src/utils/ecryptfs-mount-private:src/utils/ecryptfs-mount-private
++	src/utils/ecryptfs-rewrite-file:src/utils/ecryptfs-rewrite-file
++	src/utils/ecryptfs-setup-private:src/utils/ecryptfs-setup-private
++	src/utils/ecryptfs-setup-swap:src/utils/ecryptfs-setup-swap
++	src/utils/ecryptfs-umount-private:src/utils/ecryptfs-umount-private
++	src/utils/ecryptfs-verify:src/utils/ecryptfs-verify

Since those will now undergo pattern substitution, they should be renamed with a .in extension.

Quoted 2 lines

Also, it is usualy bad practice to generate such scripts from configure. Instead, they should be generated in Makefile.am as new targets. Yes,

You meant - replace inclusion of this ecryptfs-utils from Makefile.am ?

Quoted 8 lines

this is a bit more involved, but is much cleaner: when you change such a script, you just have to run 'make' again, rather than re-run configure.

package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch line 82

Quoted 2 lines
package/ecryptfs-utils/0003-utils-Use-printf-if-gettext-does-not-exist.patch new file +2 -0
++commonlibdir=$(libdir)/ecryptfs-utils
++commonlib_SCRIPTS=ecryptfs-common

I think 'sh-functions' is more appropriate.

So, in case of (2) then we should wait till ecryptfs's community apply the solution. In case of gettext-tiny ... as I remember Thomas did not like the idea with using gettext-tiny for target :), ehhh ... but I totally AGREE with you because your suggestions are more clear and well defined, what I tried - is to provide solution which touches not so much ectyptfs's sources but provides solution w/o gettext to finally close one gap with gettext-tiny solution :)

Back to gettext-tiny, may be it is OK to start with providing gettext-tiny (as target's gettext provider) just only with this gettext wrapper (which you suggested previously), and after take gettext-tiny patches (which I sent and Thomas adapted in his repo) and merge with solution which provides just gettext util.

Thanks Yann with your suggestions.

Regards,
Vadim Kochan

Regards,
Vadim Kochan

#5 lore raw

PATCH v2 1/1 package/ecryptfs-utils: Add support without gettext

Vadim, All,

On 2019-03-26 23:09 +0200, Vadim Kochan spake thusly:

Quoted 3 lines · Yann E. MORIN
Quoted 2 lines

On 2019-03-15 04:34 +0200, Vadim Kochan spake thusly:

Quoted 1 line

Add custom ecryptfs-common script which provides gettext wrapper as

[--SNIP--]

Quoted 9 lines
Quoted 9 lines

I know you've pourred quite some effort into this solution, but I am still not entirely convinced.

So, my position on how we should handle this in Buildroot is as follows:

1. When the real 'gettext' utility is not available (for whatever reason), then we should install our own, fake gettext, like the one I previously suggested.

Quoted 7 lines
Quoted 7 lines

2. If you are really interested, push a change upstream that makes ecryptfs-utils not require gettext, but with a solution that does not use a wrapper. see below for more on that.

3. If/when upstream supports running without a gettext utility, then we can either bump the version in Buildroot, or backport the patches.

[--SNIP--]

Quoted 8 lines
Quoted 8 lines
Quoted 7 lines

++ src/utils/ecryptfs-migrate-home:src/utils/ecryptfs-migrate-home
++ src/utils/ecryptfs-mount-private:src/utils/ecryptfs-mount-private
++ src/utils/ecryptfs-rewrite-file:src/utils/ecryptfs-rewrite-file
++ src/utils/ecryptfs-setup-private:src/utils/ecryptfs-setup-private
++ src/utils/ecryptfs-setup-swap:src/utils/ecryptfs-setup-swap
++ src/utils/ecryptfs-umount-private:src/utils/ecryptfs-umount-private
++ src/utils/ecryptfs-verify:src/utils/ecryptfs-verify

Quoted 7 lines
Quoted 5 lines

Since those will now undergo pattern substitution, they should be renamed with a .in extension.

Also, it is usualy bad practice to generate such scripts from configure. Instead, they should be generated in Makefile.am as new targets. Yes,

You meant - replace inclusion of this ecryptfs-utils from Makefile.am ?

Yes. That would IMHO be the best. But if upstream is willing to take a patch that generates them from configure, I won't be picky! ;-)

So, you could keep them generated by configure and send the patch upstream, and see what they say about it.

Quoted 11 lines
Quoted 8 lines

this is a bit more involved, but is much cleaner: when you change such a script, you just have to run 'make' again, rather than re-run configure.

Quoted 2 lines

++commonlibdir=$(libdir)/ecryptfs-utils
++commonlib_SCRIPTS=ecryptfs-common

I think 'sh-functions' is more appropriate.

So, in case of (2) then we should wait till ecryptfs's community apply the solution.

Before we can use it in Buildroot? Yes.

Quoted 2 lines

In case of gettext-tiny ... as I remember Thomas did not like the idea with using gettext-tiny for target :),

We discussed this live a few days ago, and I think I could somehow mostly convince him. I think. Probably. ;-)

He also inquired on IRC a few hours ago about my opinion, and after I exposed it, he asked that I did the reply to you. So again, I think he mostly aligns with the idea now. Hopefully! ;-)

Quoted 5 lines

ehhh ... but I
totally AGREE with you because your suggestions are more clear and well defined, what I tried - is to provide solution which touches not so much ectyptfs's sources but provides solution w/o gettext to finally close one gap with gettext-tiny solution :)

Yes, this is an "easier" first step, at least.

Quoted 5 lines

Back to gettext-tiny, may be it is OK to start with providing gettext-tiny (as target's gettext provider) just only with this gettext wrapper (which you suggested previously), and after take gettext-tiny patches (which I sent and Thomas adapted in his repo) and merge with solution which provides just gettext util.

Sorry, I am not sure I understood the above.

When we introduce gettext-tiny, it should also install this fake gettext. I.e. gettext-tiny is as much as possible a drop-in replacement for the real gettext (the package) and thus shall provide gettext (the program).

Quoted 1 line

Thanks Yann with your suggestions.

My pleasure. And thank you for staying afloat with the back-and-forth mind-switching there's been on this series. ;-)

Regards,
Yann E. MORIN.

Signature · 6 lines
.-----------------.--------------------.------------------.--------------------.
|  Yann E. MORIN  | Real-Time Embedded | /"\ ASCII RIBBON | Erics' conspiracy: |
| +33 662 376 056 | Software  Designer | \ / CAMPAIGN     |  ___               |
| +33 561 099 427 `------------.-------:  X  AGAINST      |  \e/  There is no  |
| http://ymorin.is-a-geek.org/ | _/*\_ | / \ HTML MAIL    |   v   conspiracy.  |
'------------------------------^-------^------------------^--------------------'