Skip to contentSkip to conversation

drm/bridge: dw-hdmi: disable SCDC configuration for invalid setups

PATCH In review Neil Armstrong 3 participants 5 messages Mar 15, 2019 – Mar 25, 2019

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 drm/bridge: dw-hdmi: disable SCDC configuration for invalid setups

This patch is an attempt to limit HDMI 2.0 SCDC setup when :
- the SoC embeds an HDMI 1.4 only controller
- the EDID supports SCDC but not scrambling
- the EDID supports SCDC scrambling but not for low TMDS bit rates, while only supporting low TMDS bit rates

This to avoid communicating with the SCDC DDC slave uncessary, and setting the DW-HDMI TMDS Scrambler setup when not supported by the underlying hardware.

Fixes 264fce6cc2c1 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support")

---

Rob,

this patch should also solve your issue with your 11' display, could you test it ?
If this works, I will focus on the underlying issue where the RK3399 SoC freezes in your setup.

Thanks,
Neil

 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 34 ++++++++++++++++++++---
 1 file changed, 30 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +30 -4
index a63e5f0dae56..db761329a1e3 100644
@@ -1037,6 +1037,31 @@ void dw_hdmi_phy_i2c_write(struct dw_hdmi *hdmi, unsigned short data,
 }
 EXPORT_SYMBOL_GPL(dw_hdmi_phy_i2c_write);
 
+/* Filter out invalid setups to avoid configuring SCDC and scrambling */
+static bool dw_hdmi_support_scdc(struct dw_hdmi *hdmi)
+{
+	struct drm_display_info *display = &hdmi->connector.display_info;
+
+	/* Completely disable SCDC support for older controllers */
+	if (hdmi->version < 0x200a)
+		return false;
+
+	/* Disable if SCDC is not supported, or if an HF-VSDB block is absent */
+	if (!display->hdmi.scdc.supported ||
+	    !display->hdmi.scdc.scrambling.supported)
+		return false;
+
+	/*
+	 * Disable if display only support low TMDS rates and scrambling
+	 * for low rates is not supported either
+	 */
+	if (!display->hdmi.scdc.scrambling.low_rates &&
+	    display->max_tmds_clock <= 340000)
+		return false;
+
+	return true;
+}
+
 /*
  * HDMI2.0 Specifies the following procedure for High TMDS Bit Rates:
  * - The Source shall suspend transmission of the TMDS clock and data
@@ -1055,7 +1080,7 @@ void dw_hdmi_set_high_tmds_clock_ratio(struct dw_hdmi *hdmi)
 	unsigned long mtmdsclock = hdmi->hdmi_data.video_mode.mtmdsclock;
 
 	/* Control for TMDS Bit Period/TMDS Clock-Period Ratio */
-	if (hdmi->connector.display_info.hdmi.scdc.supported) {
+	if (dw_hdmi_support_scdc(hdmi)) {
 		if (mtmdsclock > HDMI14_MAX_TMDSCLK)
 			drm_scdc_set_high_tmds_clock_ratio(hdmi->ddc, 1);
 		else
@@ -1579,8 +1604,9 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 
 	/* Set up HDMI_FC_INVIDCONF */
 	inv_val = (hdmi->hdmi_data.hdcp_enable ||
-		   vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
-		   hdmi_info->scdc.scrambling.low_rates ?
+		   (dw_hdmi_support_scdc(hdmi) &&
+		    (vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
+		     hdmi_info->scdc.scrambling.low_rates)) ?
 		HDMI_FC_INVIDCONF_HDCP_KEEPOUT_ACTIVE :
 		HDMI_FC_INVIDCONF_HDCP_KEEPOUT_INACTIVE);
 
@@ -1646,7 +1672,7 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 	}
 
 	/* Scrambling Control */
-	if (hdmi_info->scdc.supported) {
+	if (dw_hdmi_support_scdc(hdmi)) {
 		if (vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
 		    hdmi_info->scdc.scrambling.low_rates) {
 			/*
Signature · 1 line
2.20.1
Tested-by on v1 1/1
#1 lore raw
Quoted 14 lines · Neil Armstrong

This patch is an attempt to limit HDMI 2.0 SCDC setup when :
- the SoC embeds an HDMI 1.4 only controller
- the EDID supports SCDC but not scrambling
- the EDID supports SCDC scrambling but not for low TMDS bit rates, while only supporting low TMDS bit rates

This to avoid communicating with the SCDC DDC slave uncessary, and setting the DW-HDMI TMDS Scrambler setup when not supported by the underlying hardware.

Fixes 264fce6cc2c1 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support")
Quoted 6 lines

---

Rob,

this patch should also solve your issue with your 11' display, could you test it ?

That works for me.

Too answer your question on the other thread, there's not really any model name for the panel I have. Probably what's in the EDID is the best thing to go on.

Here's the panel on Amazon:

https://www.amazon.com/gp/product/B07GDDG3WJ/ref=ppx_yo_dt_b_asin_title_o00_s01?ie=UTF8&psc=1

Quoted 78 lines

If this works, I will focus on the underlying issue where the RK3399 SoC freezes in your setup.

Thanks,
Neil

 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 34 ++++++++++++++++++++---
 1 file changed, 30 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +30 -5
index a63e5f0dae56..db761329a1e3 100644
@@ -1037,6 +1037,31 @@ void dw_hdmi_phy_i2c_write(struct dw_hdmi *hdmi, unsigned short data,
 }
 EXPORT_SYMBOL_GPL(dw_hdmi_phy_i2c_write);
 
+/* Filter out invalid setups to avoid configuring SCDC and scrambling */
+static bool dw_hdmi_support_scdc(struct dw_hdmi *hdmi)
+{
+       struct drm_display_info *display = &hdmi->connector.display_info;
+
+       /* Completely disable SCDC support for older controllers */
+       if (hdmi->version < 0x200a)
+               return false;
+
+       /* Disable if SCDC is not supported, or if an HF-VSDB block is absent */
+       if (!display->hdmi.scdc.supported ||
+           !display->hdmi.scdc.scrambling.supported)
+               return false;
+
+       /*
+        * Disable if display only support low TMDS rates and scrambling
+        * for low rates is not supported either
+        */
+       if (!display->hdmi.scdc.scrambling.low_rates &&
+           display->max_tmds_clock <= 340000)
+               return false;
+
+       return true;
+}
+
 /*
  * HDMI2.0 Specifies the following procedure for High TMDS Bit Rates:
  * - The Source shall suspend transmission of the TMDS clock and data
@@ -1055,7 +1080,7 @@ void dw_hdmi_set_high_tmds_clock_ratio(struct dw_hdmi *hdmi)
        unsigned long mtmdsclock = hdmi->hdmi_data.video_mode.mtmdsclock;
 
        /* Control for TMDS Bit Period/TMDS Clock-Period Ratio */
-       if (hdmi->connector.display_info.hdmi.scdc.supported) {
+       if (dw_hdmi_support_scdc(hdmi)) {
                if (mtmdsclock > HDMI14_MAX_TMDSCLK)
                        drm_scdc_set_high_tmds_clock_ratio(hdmi->ddc, 1);
                else
@@ -1579,8 +1604,9 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 
        /* Set up HDMI_FC_INVIDCONF */
        inv_val = (hdmi->hdmi_data.hdcp_enable ||
-                  vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
-                  hdmi_info->scdc.scrambling.low_rates ?
+                  (dw_hdmi_support_scdc(hdmi) &&
+                   (vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
+                    hdmi_info->scdc.scrambling.low_rates)) ?
                HDMI_FC_INVIDCONF_HDCP_KEEPOUT_ACTIVE :
                HDMI_FC_INVIDCONF_HDCP_KEEPOUT_INACTIVE);
 
@@ -1646,7 +1672,7 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
        }
 
        /* Scrambling Control */
-       if (hdmi_info->scdc.supported) {
+       if (dw_hdmi_support_scdc(hdmi)) {
                if (vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
                    hdmi_info->scdc.scrambling.low_rates) {
                        /*
--

2.20.1

#2 lore raw
In reply to Neil Armstrong

Hi Andrzej, Laurent,

Gentle ping,
Did you have time to review this fix ?

Thanks !
Neil

Quoted 95 lines · Neil Armstrong

This patch is an attempt to limit HDMI 2.0 SCDC setup when :
- the SoC embeds an HDMI 1.4 only controller
- the EDID supports SCDC but not scrambling
- the EDID supports SCDC scrambling but not for low TMDS bit rates, while only supporting low TMDS bit rates

This to avoid communicating with the SCDC DDC slave uncessary, and setting the DW-HDMI TMDS Scrambler setup when not supported by the underlying hardware.

Fixes 264fce6cc2c1 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support")

---

Rob,

this patch should also solve your issue with your 11' display, could you test it ?
If this works, I will focus on the underlying issue where the RK3399 SoC freezes in your setup.

Thanks,
Neil

 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 34 ++++++++++++++++++++---
 1 file changed, 30 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +30 -4
index a63e5f0dae56..db761329a1e3 100644
@@ -1037,6 +1037,31 @@ void dw_hdmi_phy_i2c_write(struct dw_hdmi *hdmi, unsigned short data,
 }
 EXPORT_SYMBOL_GPL(dw_hdmi_phy_i2c_write);
 
+/* Filter out invalid setups to avoid configuring SCDC and scrambling */
+static bool dw_hdmi_support_scdc(struct dw_hdmi *hdmi)
+{
+	struct drm_display_info *display = &hdmi->connector.display_info;
+
+	/* Completely disable SCDC support for older controllers */
+	if (hdmi->version < 0x200a)
+		return false;
+
+	/* Disable if SCDC is not supported, or if an HF-VSDB block is absent */
+	if (!display->hdmi.scdc.supported ||
+	    !display->hdmi.scdc.scrambling.supported)
+		return false;
+
+	/*
+	 * Disable if display only support low TMDS rates and scrambling
+	 * for low rates is not supported either
+	 */
+	if (!display->hdmi.scdc.scrambling.low_rates &&
+	    display->max_tmds_clock <= 340000)
+		return false;
+
+	return true;
+}
+
 /*
  * HDMI2.0 Specifies the following procedure for High TMDS Bit Rates:
  * - The Source shall suspend transmission of the TMDS clock and data
@@ -1055,7 +1080,7 @@ void dw_hdmi_set_high_tmds_clock_ratio(struct dw_hdmi *hdmi)
 	unsigned long mtmdsclock = hdmi->hdmi_data.video_mode.mtmdsclock;
 
 	/* Control for TMDS Bit Period/TMDS Clock-Period Ratio */
-	if (hdmi->connector.display_info.hdmi.scdc.supported) {
+	if (dw_hdmi_support_scdc(hdmi)) {
 		if (mtmdsclock > HDMI14_MAX_TMDSCLK)
 			drm_scdc_set_high_tmds_clock_ratio(hdmi->ddc, 1);
 		else
@@ -1579,8 +1604,9 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 
 	/* Set up HDMI_FC_INVIDCONF */
 	inv_val = (hdmi->hdmi_data.hdcp_enable ||
-		   vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
-		   hdmi_info->scdc.scrambling.low_rates ?
+		   (dw_hdmi_support_scdc(hdmi) &&
+		    (vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
+		     hdmi_info->scdc.scrambling.low_rates)) ?
 		HDMI_FC_INVIDCONF_HDCP_KEEPOUT_ACTIVE :
 		HDMI_FC_INVIDCONF_HDCP_KEEPOUT_INACTIVE);
 
@@ -1646,7 +1672,7 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 	}
 
 	/* Scrambling Control */
-	if (hdmi_info->scdc.supported) {
+	if (dw_hdmi_support_scdc(hdmi)) {
 		if (vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
 		    hdmi_info->scdc.scrambling.low_rates) {
 			/*
Reviewed-by on v1 1/1
#3 lore raw
In reply to Neil Armstrong
Quoted 74 lines · Neil Armstrong

This patch is an attempt to limit HDMI 2.0 SCDC setup when :
- the SoC embeds an HDMI 1.4 only controller
- the EDID supports SCDC but not scrambling
- the EDID supports SCDC scrambling but not for low TMDS bit rates, while only supporting low TMDS bit rates

This to avoid communicating with the SCDC DDC slave uncessary, and setting the DW-HDMI TMDS Scrambler setup when not supported by the underlying hardware.

Fixes 264fce6cc2c1 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support")

---

Rob,

this patch should also solve your issue with your 11' display, could you test it ?
If this works, I will focus on the underlying issue where the RK3399 SoC freezes in your setup.

Thanks,
Neil

 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 34 ++++++++++++++++++++---
 1 file changed, 30 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +26 -1
index a63e5f0dae56..db761329a1e3 100644
@@ -1037,6 +1037,31 @@ void dw_hdmi_phy_i2c_write(struct dw_hdmi *hdmi, unsigned short data,
 }
 EXPORT_SYMBOL_GPL(dw_hdmi_phy_i2c_write);
 
+/* Filter out invalid setups to avoid configuring SCDC and scrambling */
+static bool dw_hdmi_support_scdc(struct dw_hdmi *hdmi)
+{
+	struct drm_display_info *display = &hdmi->connector.display_info;
+
+	/* Completely disable SCDC support for older controllers */
+	if (hdmi->version < 0x200a)
+		return false;
+
+	/* Disable if SCDC is not supported, or if an HF-VSDB block is absent */
+	if (!display->hdmi.scdc.supported ||
+	    !display->hdmi.scdc.scrambling.supported)
+		return false;
+
+	/*
+	 * Disable if display only support low TMDS rates and scrambling
+	 * for low rates is not supported either
+	 */
+	if (!display->hdmi.scdc.scrambling.low_rates &&
+	    display->max_tmds_clock <= 340000)
+		return false;
+
+	return true;
+}
+
 /*
  * HDMI2.0 Specifies the following procedure for High TMDS Bit Rates:
  * - The Source shall suspend transmission of the TMDS clock and data
@@ -1055,7 +1080,7 @@ void dw_hdmi_set_high_tmds_clock_ratio(struct dw_hdmi *hdmi)
 	unsigned long mtmdsclock = hdmi->hdmi_data.video_mode.mtmdsclock;
 
 	/* Control for TMDS Bit Period/TMDS Clock-Period Ratio */
-	if (hdmi->connector.display_info.hdmi.scdc.supported) {
+	if (dw_hdmi_support_scdc(hdmi)) {
 		if (mtmdsclock > HDMI14_MAX_TMDSCLK)
 			drm_scdc_set_high_tmds_clock_ratio(hdmi->ddc, 1);
 		else

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c static void hdmi_av_composer(struct dw_hdmi *hdmi, · line 1611

Quoted 10 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +3 -2
@@ -1579,8 +1604,9 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 
 	/* Set up HDMI_FC_INVIDCONF */
 	inv_val = (hdmi->hdmi_data.hdcp_enable ||
-		   vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
-		   hdmi_info->scdc.scrambling.low_rates ?
+		   (dw_hdmi_support_scdc(hdmi) &&
+		    (vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
+		     hdmi_info->scdc.scrambling.low_rates)) ?
 		HDMI_FC_INVIDCONF_HDCP_KEEPOUT_ACTIVE :
 		HDMI_FC_INVIDCONF_HDCP_KEEPOUT_INACTIVE);

The condition is hard to read, but I have no idea atm how make it compact and pretty :)

Anyway:

As I remember you can queue it to drm-misc, if not I can do it, just let me know.

 --
Regards
Andrzej

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c static void hdmi_av_composer(struct dw_hdmi *hdmi, · line 1678

Quoted 10 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +1 -1
@@ -1646,7 +1672,7 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 	}
 
 	/* Scrambling Control */
-	if (hdmi_info->scdc.supported) {
+	if (dw_hdmi_support_scdc(hdmi)) {
 		if (vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
 		    hdmi_info->scdc.scrambling.low_rates) {
 			/*

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#4 lore raw
Quoted 76 lines · Andrzej Hajda
Quoted 75 lines · Neil Armstrong

This patch is an attempt to limit HDMI 2.0 SCDC setup when :
- the SoC embeds an HDMI 1.4 only controller
- the EDID supports SCDC but not scrambling
- the EDID supports SCDC scrambling but not for low TMDS bit rates, while only supporting low TMDS bit rates

This to avoid communicating with the SCDC DDC slave uncessary, and setting the DW-HDMI TMDS Scrambler setup when not supported by the underlying hardware.

Fixes 264fce6cc2c1 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support")

---

Rob,

this patch should also solve your issue with your 11' display, could you test it ?
If this works, I will focus on the underlying issue where the RK3399 SoC freezes in your setup.

Thanks,
Neil

 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 34 ++++++++++++++++++++---
 1 file changed, 30 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +26 -1
index a63e5f0dae56..db761329a1e3 100644
@@ -1037,6 +1037,31 @@ void dw_hdmi_phy_i2c_write(struct dw_hdmi *hdmi, unsigned short data,
 }
 EXPORT_SYMBOL_GPL(dw_hdmi_phy_i2c_write);
 
+/* Filter out invalid setups to avoid configuring SCDC and scrambling */
+static bool dw_hdmi_support_scdc(struct dw_hdmi *hdmi)
+{
+	struct drm_display_info *display = &hdmi->connector.display_info;
+
+	/* Completely disable SCDC support for older controllers */
+	if (hdmi->version < 0x200a)
+		return false;
+
+	/* Disable if SCDC is not supported, or if an HF-VSDB block is absent */
+	if (!display->hdmi.scdc.supported ||
+	    !display->hdmi.scdc.scrambling.supported)
+		return false;
+
+	/*
+	 * Disable if display only support low TMDS rates and scrambling
+	 * for low rates is not supported either
+	 */
+	if (!display->hdmi.scdc.scrambling.low_rates &&
+	    display->max_tmds_clock <= 340000)
+		return false;
+
+	return true;
+}
+
 /*
  * HDMI2.0 Specifies the following procedure for High TMDS Bit Rates:
  * - The Source shall suspend transmission of the TMDS clock and data
@@ -1055,7 +1080,7 @@ void dw_hdmi_set_high_tmds_clock_ratio(struct dw_hdmi *hdmi)
 	unsigned long mtmdsclock = hdmi->hdmi_data.video_mode.mtmdsclock;
 
 	/* Control for TMDS Bit Period/TMDS Clock-Period Ratio */
-	if (hdmi->connector.display_info.hdmi.scdc.supported) {
+	if (dw_hdmi_support_scdc(hdmi)) {
 		if (mtmdsclock > HDMI14_MAX_TMDSCLK)
 			drm_scdc_set_high_tmds_clock_ratio(hdmi->ddc, 1);
 		else
@@ -1579,8 +1604,9 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 
Quoted 13 lines

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c static void hdmi_av_composer(struct dw_hdmi *hdmi, · line 1611

Quoted 9 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +3 -2
 	/* Set up HDMI_FC_INVIDCONF */
 	inv_val = (hdmi->hdmi_data.hdcp_enable ||
-		   vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
-		   hdmi_info->scdc.scrambling.low_rates ?
+		   (dw_hdmi_support_scdc(hdmi) &&
+		    (vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
+		     hdmi_info->scdc.scrambling.low_rates)) ?
 		HDMI_FC_INVIDCONF_HDCP_KEEPOUT_ACTIVE :
 		HDMI_FC_INVIDCONF_HDCP_KEEPOUT_INACTIVE);

The condition is hard to read, but I have no idea atm how make it compact and pretty :)

I made my best to make it barely readable...

We may need to reword this condition since on the DW-HMI in the Allwinner H6, this is no more needed for scrambling !

Quoted 8 lines

Anyway:

As I remember you can queue it to drm-misc, if not I can do it, just let me know.

I can and I'm queuing it right now, thanks for the review !

Neil

Quoted 20 lines

 --
Regards
Andrzej

Quoted 10 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +1 -1
@@ -1646,7 +1672,7 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 	}
 
 	/* Scrambling Control */
-	if (hdmi_info->scdc.supported) {
+	if (dw_hdmi_support_scdc(hdmi)) {
 		if (vmode->mtmdsclock > HDMI14_MAX_TMDSCLK ||
 		    hdmi_info->scdc.scrambling.low_rates) {
 			/*