Skip to contentSkip to conversation

extcon: intel: Split out some definitions to a common header

PATCH Superseded Andy Shevchenko 2 participants 8 messages Mar 18, 2019 – Mar 19, 2019

Subsystems (2)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 extcon: intel: Split out some definitions to a common header

We are going to use some definitions in the other Intel extcon drivers, thus, split out them to a common header file.

---
 drivers/extcon/extcon-intel-cht-wc.c | 21 +++++++--------------
 drivers/extcon/extcon-intel.h        | 20 ++++++++++++++++++++
 2 files changed, 27 insertions(+), 14 deletions(-)
 create mode 100644 drivers/extcon/extcon-intel.h
drivers/extcon/extcon-intel-cht-wc.c +7 -14
index 5ef215297101..110bd38a4d24 100644
@@ -17,6 +17,8 @@
 #include <linux/regmap.h>
 #include <linux/slab.h>
 
+#include "extcon-intel.h"
+
 #define CHT_WC_PHYCTRL			0x5e07
 
 #define CHT_WC_CHGRCTRL0		0x5e16
@@ -65,15 +67,6 @@
 #define CHT_WC_VBUS_GPIO_CTLO_DRV_OD	BIT(4)
 #define CHT_WC_VBUS_GPIO_CTLO_DIR_OUT	BIT(5)
 
-enum cht_wc_usb_id {
-	USB_ID_OTG,
-	USB_ID_GND,
-	USB_ID_FLOAT,
-	USB_RID_A,
-	USB_RID_B,
-	USB_RID_C,
-};
-
 enum cht_wc_mux_select {
 	MUX_SEL_PMIC = 0,
 	MUX_SEL_SOC,
@@ -101,9 +94,9 @@ static int cht_wc_extcon_get_id(struct cht_wc_extcon_data *ext, int pwrsrc_sts)
 {
 	switch ((pwrsrc_sts & CHT_WC_PWRSRC_USBID_MASK) >> CHT_WC_PWRSRC_USBID_SHIFT) {
 	case CHT_WC_PWRSRC_RID_GND:
-		return USB_ID_GND;
+		return INTEL_USB_ID_GND;
 	case CHT_WC_PWRSRC_RID_FLOAT:
-		return USB_ID_FLOAT;
+		return INTEL_USB_ID_FLOAT;
 	case CHT_WC_PWRSRC_RID_ACA:
 	default:
 		/*
@@ -111,7 +104,7 @@ static int cht_wc_extcon_get_id(struct cht_wc_extcon_data *ext, int pwrsrc_sts)
 		 * the USBID GPADC channel here and determine ACA role
 		 * based on that.
 		 */
-		return USB_ID_FLOAT;
+		return INTEL_USB_ID_FLOAT;
 	}
 }
 
@@ -221,7 +214,7 @@ static void cht_wc_extcon_pwrsrc_event(struct cht_wc_extcon_data *ext)
 	}
 
 	id = cht_wc_extcon_get_id(ext, pwrsrc_sts);
-	if (id == USB_ID_GND) {
+	if (id == INTEL_USB_ID_GND) {
 		/* The 5v boost causes a false VBUS / SDP detect, skip */
 		goto charger_det_done;
 	}
@@ -248,7 +241,7 @@ static void cht_wc_extcon_pwrsrc_event(struct cht_wc_extcon_data *ext)
 		ext->previous_cable = cable;
 	}
 
-	ext->usb_host = ((id == USB_ID_GND) || (id == USB_RID_A));
+	ext->usb_host = ((id == INTEL_USB_ID_GND) || (id == INTEL_USB_RID_A));
 	extcon_set_state_sync(ext->edev, EXTCON_USB_HOST, ext->usb_host);
 }
 
drivers/extcon/extcon-intel.h new file +20 -0
new file mode 100644
index 000000000000..455986b2b004
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Header file for Intel extcon hardware
+ *
+ * Copyright (C) 2018 Intel Corporation. All rights reserved.
+ */
+
+#ifndef __EXTCON_INTEL_H__
+#define __EXTCON_INTEL_H__
+
+enum extcon_intel_usb_id {
+	INTEL_USB_ID_OTG,
+	INTEL_USB_ID_GND,
+	INTEL_USB_ID_FLOAT,
+	INTEL_USB_RID_A,
+	INTEL_USB_RID_B,
+	INTEL_USB_RID_C,
+};
+
+#endif	/* __EXTCON_INTEL_H__ */
Signature · 1 line
2.20.1
#1 lore raw

PATCH 2/2 extcon: mrfld: Introduce extcon driver for Basin Cove PMIC

TBD

---
 drivers/extcon/Kconfig              |   7 +
 drivers/extcon/Makefile             |   1 +
 drivers/extcon/extcon-intel-mrfld.c | 256 ++++++++++++++++++++++++++++
 3 files changed, 264 insertions(+)
 create mode 100644 drivers/extcon/extcon-intel-mrfld.c
drivers/extcon/Kconfig +7 -0
index 8e17149655f0..75349c6cc89e 100644
@@ -60,6 +60,13 @@ config EXTCON_INTEL_CHT_WC
 	  Say Y here to enable extcon support for charger detection / control
 	  on the Intel Cherrytrail Whiskey Cove PMIC.
 
+config EXTCON_INTEL_MRFLD
+	tristate "Intel MErrifield Basin Cove PMIC extcon driver"
+	depends on INTEL_SOC_PMIC_MRFLD
+	help
+	  Say Y here to enable extcon support for charger detection / control
+	  on the Intel Merrifiel Basin Cove PMIC.
+
 config EXTCON_MAX14577
 	tristate "Maxim MAX14577/77836 EXTCON Support"
 	depends on MFD_MAX14577
drivers/extcon/Makefile +1 -0
index 261ce4cfe209..d3941a735df3 100644
@@ -11,6 +11,7 @@ obj-$(CONFIG_EXTCON_AXP288)	+= extcon-axp288.o
 obj-$(CONFIG_EXTCON_GPIO)	+= extcon-gpio.o
 obj-$(CONFIG_EXTCON_INTEL_INT3496) += extcon-intel-int3496.o
 obj-$(CONFIG_EXTCON_INTEL_CHT_WC) += extcon-intel-cht-wc.o
+obj-$(CONFIG_EXTCON_INTEL_MRFLD) += extcon-intel-mrfld.o
 obj-$(CONFIG_EXTCON_MAX14577)	+= extcon-max14577.o
 obj-$(CONFIG_EXTCON_MAX3355)	+= extcon-max3355.o
 obj-$(CONFIG_EXTCON_MAX77693)	+= extcon-max77693.o
drivers/extcon/extcon-intel-mrfld.c new file +256 -0

256 lines not on this page · raw message

Signature · 1 line
2.20.1
#2 lore raw

Re: [PATCH v1 2/2] extcon: mrfld: Introduce extcon driver for Basin Cove PMIC

Quoted 1 line · Andy Shevchenko

TBD

Oops.
I though I have written it already.

I will wait for other comments today and sent a new version with commit message filled as follows:

On Intel Merrifield the Basin Cove PMIC provides a feature to detect the USB connection type. This driver utilizes the feature in order to support the USB dual role detection.

Quoted 14 lines
---
 drivers/extcon/Kconfig              |   7 +
 drivers/extcon/Makefile             |   1 +
 drivers/extcon/extcon-intel-mrfld.c | 256 ++++++++++++++++++++++++++++
 3 files changed, 264 insertions(+)
 create mode 100644 drivers/extcon/extcon-intel-mrfld.c
drivers/extcon/Kconfig +0 -0
index 8e17149655f0..75349c6cc89e 100644

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 65

Quoted 6 lines
drivers/extcon/Kconfig +2 -0
@@ -60,6 +60,13 @@ config EXTCON_INTEL_CHT_WC
 	  Say Y here to enable extcon support for charger detection / control
 	  on the Intel Cherrytrail Whiskey Cove PMIC.
 
+config EXTCON_INTEL_MRFLD
 
+	tristate "Intel MErrifield Basin Cove PMIC extcon driver"

ME -> Me (will be fixed)

Quoted 26 lines
drivers/extcon/Kconfig +5 -0
+	depends on INTEL_SOC_PMIC_MRFLD
+	help
+	  Say Y here to enable extcon support for charger detection / control
+	  on the Intel Merrifiel Basin Cove PMIC.
+
 config EXTCON_MAX14577
 	tristate "Maxim MAX14577/77836 EXTCON Support"
drivers/extcon/Kconfig +0 -0
 	depends on MFD_MAX14577
drivers/extcon/Makefile +1 -0
index 261ce4cfe209..d3941a735df3 100644
@@ -11,6 +11,7 @@ obj-$(CONFIG_EXTCON_AXP288)	+= extcon-axp288.o
 obj-$(CONFIG_EXTCON_GPIO)	+= extcon-gpio.o
 obj-$(CONFIG_EXTCON_INTEL_INT3496) += extcon-intel-int3496.o
 obj-$(CONFIG_EXTCON_INTEL_CHT_WC) += extcon-intel-cht-wc.o
+obj-$(CONFIG_EXTCON_INTEL_MRFLD) += extcon-intel-mrfld.o
 obj-$(CONFIG_EXTCON_MAX14577)	+= extcon-max14577.o
 obj-$(CONFIG_EXTCON_MAX3355)	+= extcon-max3355.o
 obj-$(CONFIG_EXTCON_MAX77693)	+= extcon-max77693.o
drivers/extcon/extcon-intel-mrfld.c new file +0 -0
new file mode 100644
index 000000000000..d45db4975b5f

drivers/extcon/extcon-intel-mrfld.c line 5

Quoted 5 lines
drivers/extcon/extcon-intel-mrfld.c new file +5 -0
@@ -0,0 +1,256 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Extcon driver for Basin Cove PMIC
+ *
+ * Copyright (c) 2018, Intel Corporation.

2019 I suppose :-)

Quoted 254 lines
drivers/extcon/extcon-intel-mrfld.c new file +251 -0
+ * Author: Andy Shevchenko <[email protected]>
+ */
+
+#include <linux/extcon-provider.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/intel_soc_pmic.h>
+#include <linux/mfd/intel_soc_pmic_mrfld.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "extcon-intel.h"
+
+#define BCOVE_USBIDCTRL			0x19
+#define BCOVE_USBIDCTRL_ID		BIT(0)
+#define BCOVE_USBIDCTRL_ACA		BIT(1)
+#define BCOVE_USBIDCTRL_ALL	(BCOVE_USBIDCTRL_ID | BCOVE_USBIDCTRL_ACA)
+
+#define BCOVE_USBIDSTS			0x1a
+#define BCOVE_USBIDSTS_GND		BIT(0)
+#define BCOVE_USBIDSTS_RARBRC_MASK	GENMASK(2, 1)
+#define BCOVE_USBIDSTS_RARBRC_SHIFT	1
+#define BCOVE_USBIDSTS_NO_ACA		0
+#define BCOVE_USBIDSTS_R_ID_A		1
+#define BCOVE_USBIDSTS_R_ID_B		2
+#define BCOVE_USBIDSTS_R_ID_C		3
+#define BCOVE_USBIDSTS_FLOAT		BIT(3)
+#define BCOVE_USBIDSTS_SHORT		BIT(4)
+
+#define BCOVE_CHGRIRQ_ALL	(BCOVE_CHGRIRQ_VBUSDET | BCOVE_CHGRIRQ_DCDET | \
+				 BCOVE_CHGRIRQ_BATTDET | BCOVE_CHGRIRQ_USBIDDET)
+
+#define BCOVE_CHGRCTRL0			0x4b
+#define BCOVE_CHGRCTRL0_CHGRRESET	BIT(0)
+#define BCOVE_CHGRCTRL0_EMRGCHREN	BIT(1)
+#define BCOVE_CHGRCTRL0_EXTCHRDIS	BIT(2)
+#define BCOVE_CHGRCTRL0_SWCONTROL	BIT(3)
+#define BCOVE_CHGRCTRL0_TTLCK		BIT(4)
+#define BCOVE_CHGRCTRL0_BIT_5		BIT(5)
+#define BCOVE_CHGRCTRL0_BIT_6		BIT(6)
+#define BCOVE_CHGRCTRL0_CHR_WDT_NOKICK	BIT(7)
+
+struct mrfld_extcon_data {
+	struct device *dev;
+	struct regmap *regmap;
+	struct extcon_dev *edev;
+	unsigned int status;
+	unsigned int id;
+};
+
+static const unsigned int mrfld_extcon_cable[] = {
+	EXTCON_USB,
+	EXTCON_USB_HOST,
+	EXTCON_CHG_USB_SDP,
+	EXTCON_CHG_USB_CDP,
+	EXTCON_CHG_USB_DCP,
+	EXTCON_CHG_USB_ACA,
+	EXTCON_NONE,
+};
+
+static int mrfld_extcon_clear(struct mrfld_extcon_data *data, unsigned int reg,
+			      unsigned int mask)
+{
+	return regmap_update_bits(data->regmap, reg, mask, 0x00);
+}
+
+static int mrfld_extcon_set(struct mrfld_extcon_data *data, unsigned int reg,
+			    unsigned int mask)
+{
+	return regmap_update_bits(data->regmap, reg, mask, 0xff);
+}
+
+static int mrfld_extcon_get_id(struct mrfld_extcon_data *data)
+{
+	struct regmap *regmap = data->regmap;
+	unsigned int id;
+	bool ground;
+	int ret;
+
+	ret = regmap_read(regmap, BCOVE_USBIDSTS, &id);
+	if (ret)
+		return ret;
+
+	if (id & BCOVE_USBIDSTS_FLOAT)
+		return INTEL_USB_ID_FLOAT;
+
+	switch ((id & BCOVE_USBIDSTS_RARBRC_MASK) >> BCOVE_USBIDSTS_RARBRC_SHIFT) {
+	case BCOVE_USBIDSTS_R_ID_A:
+		return INTEL_USB_RID_A;
+	case BCOVE_USBIDSTS_R_ID_B:
+		return INTEL_USB_RID_B;
+	case BCOVE_USBIDSTS_R_ID_C:
+		return INTEL_USB_RID_C;
+	}
+
+	/*
+	 * PMIC A0 reports USBIDSTS_GND = 1 for ID_GND,
+	 * but PMIC B0 reports USBIDSTS_GND = 0 for ID_GND.
+	 * Thus we must check this bit at last.
+	 */
+	ground = id & BCOVE_USBIDSTS_GND;
+	switch ('A' + BCOVE_MAJOR(data->id)) {
+	case 'A':
+		return ground ? INTEL_USB_ID_GND : INTEL_USB_ID_FLOAT;
+	case 'B':
+		return ground ? INTEL_USB_ID_FLOAT : INTEL_USB_ID_GND;
+	}
+
+	/* Unknown or unsupported type */
+	return INTEL_USB_ID_FLOAT;
+}
+
+static int mrfld_extcon_role_detect(struct mrfld_extcon_data *data)
+{
+	unsigned int id;
+	bool usb_host;
+	int ret;
+
+	ret = mrfld_extcon_get_id(data);
+	if (ret < 0)
+		return ret;
+
+	id = ret;
+
+	usb_host = (id == INTEL_USB_ID_GND) || (id == INTEL_USB_RID_A);
+	extcon_set_state_sync(data->edev, EXTCON_USB_HOST, usb_host);
+
+	return 0;
+}
+
+static int mrfld_extcon_cable_detect(struct mrfld_extcon_data *data)
+{
+	struct regmap *regmap = data->regmap;
+	unsigned int status;
+	int ret;
+
+	/*
+	 * It seems SCU firmware clears the content of BCOVE_CHGRIRQ1
+	 * and makes it useless for OS. Instead we compare a previously
+	 * stored status to the current one, provided by BCOVE_SCHGRIRQ1.
+	 */
+	ret = regmap_read(regmap, BCOVE_SCHGRIRQ1, &status);
+	if (ret)
+		return ret;
+
+	if (!(status ^ data->status))
+		return -ENODATA;
+
+	if ((status ^ data->status) & BCOVE_CHGRIRQ_USBIDDET)
+		ret = mrfld_extcon_role_detect(data);
+
+	data->status = status;
+	return ret;
+}
+
+static irqreturn_t mrfld_extcon_interrupt(int irq, void *dev_id)
+{
+	struct mrfld_extcon_data *data = dev_id;
+	int ret;
+
+	ret = mrfld_extcon_cable_detect(data);
+
+	mrfld_extcon_clear(data, BCOVE_MIRQLVL1, BCOVE_LVL1_CHGR);
+
+	return ret ? IRQ_NONE: IRQ_HANDLED;
+}
+
+static int mrfld_extcon_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct intel_soc_pmic *pmic = dev_get_drvdata(dev->parent);
+	struct regmap *regmap = pmic->regmap;
+	struct mrfld_extcon_data *data;
+	unsigned int id;
+	int irq, ret;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->dev = dev;
+	data->regmap = regmap;
+
+	data->edev = devm_extcon_dev_allocate(dev, mrfld_extcon_cable);
+	if (IS_ERR(data->edev))
+		return -ENOMEM;
+
+	ret = devm_extcon_dev_register(dev, data->edev);
+	if (ret < 0) {
+		dev_err(dev, "can't register extcon device: %d\n", ret);
+		return ret;
+	}
+
+	ret = devm_request_threaded_irq(dev, irq, NULL, mrfld_extcon_interrupt,
+					IRQF_ONESHOT | IRQF_SHARED, pdev->name,
+					data);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(regmap, BCOVE_ID, &id);
+	if (ret)
+		return ret;
+
+	data->id = id;
+
+	mrfld_extcon_set(data, BCOVE_CHGRCTRL0, BCOVE_CHGRCTRL0_SWCONTROL);
+
+	/* Get initial state */
+	mrfld_extcon_role_detect(data);
+
+	mrfld_extcon_clear(data, BCOVE_MIRQLVL1, BCOVE_LVL1_CHGR);
+	mrfld_extcon_clear(data, BCOVE_MCHGRIRQ1, BCOVE_CHGRIRQ_ALL);
+
+	mrfld_extcon_set(data, BCOVE_USBIDCTRL, BCOVE_USBIDCTRL_ALL);
+
+	platform_set_drvdata(pdev, data);
+	return 0;
+}
+
+static int mrfld_extcon_remove(struct platform_device *pdev)
+{
+	struct mrfld_extcon_data *data = platform_get_drvdata(pdev);
+
+	mrfld_extcon_clear(data, BCOVE_CHGRCTRL0, BCOVE_CHGRCTRL0_SWCONTROL);
+	return 0;
+}
+
+static const struct platform_device_id mrfld_extcon_id_table[] = {
+	{ .name = "mrfld_bcove_extcon" },
+	{}
+};
+MODULE_DEVICE_TABLE(platform, mrfld_extcon_id_table);
+
+static struct platform_driver mrfld_extcon_driver = {
+	.driver = {
+		.name	= KBUILD_MODNAME,
+	},
+	.probe		= mrfld_extcon_probe,
+	.remove		= mrfld_extcon_remove,
+	.id_table	= mrfld_extcon_id_table,
+};
+module_platform_driver(mrfld_extcon_driver);
+
+MODULE_AUTHOR("Andy Shevchenko <[email protected]>");
+MODULE_DESCRIPTION("Extcon driver for Basin Cove PMIC");
+MODULE_LICENSE("GPL v2");
Signature · 1 line
2.20.1
Signature · 2 lines
With Best Regards,
Andy Shevchenko
maintainer
#3 lore raw

Re: [PATCH v1 2/2] extcon: mrfld: Introduce extcon driver for Basin Cove PMIC

Hi Andy,

Thanks for comment. I add my comments
and then you have to rebase it on latest v5.0-rc1
because the merge conflict happen on v5.0-rc1.

Quoted 30 lines · Andy Shevchenko
Quoted 1 line · Andy Shevchenko

TBD

Oops.
I though I have written it already.

I will wait for other comments today and sent a new version with commit message filled as follows:

On Intel Merrifield the Basin Cove PMIC provides a feature to detect the USB connection type. This driver utilizes the feature in order to support the USB dual role detection.

Quoted 17 lines
---
 drivers/extcon/Kconfig              |   7 +
 drivers/extcon/Makefile             |   1 +
 drivers/extcon/extcon-intel-mrfld.c | 256 ++++++++++++++++++++++++++++
 3 files changed, 264 insertions(+)
 create mode 100644 drivers/extcon/extcon-intel-mrfld.c
drivers/extcon/Kconfig +0 -0
index 8e17149655f0..75349c6cc89e 100644
@@ -60,6 +60,13 @@ config EXTCON_INTEL_CHT_WC
 	  Say Y here to enable extcon support for charger detection / control
 	  on the Intel Cherrytrail Whiskey Cove PMIC.
 
Quoted 7 lines

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 64

Quoted 3 lines
drivers/extcon/Kconfig +2 -0
+config EXTCON_INTEL_MRFLD
 
+	tristate "Intel MErrifield Basin Cove PMIC extcon driver"

ME -> Me (will be fixed)

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 65

Quoted 1 line
drivers/extcon/Kconfig +1 -0
+	depends on INTEL_SOC_PMIC_MRFLD

This driver uses the regmap interface. So, you better to add following dependency?
- select REGMAP_I2C or REGMAP_SPI

But, if 'INTEL_SOC_PMIC_MRFLE' selects already REGMAP_* configuration. It is not necessary.

Quoted 3 lines

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 68

Quoted 3 lines
drivers/extcon/Kconfig +3 -0
+	help
+	  Say Y here to enable extcon support for charger detection / control
+	  on the Intel Merrifiel Basin Cove PMIC.

What is correct word?
- Merrifield? is used on above
- Merrifiel?

Quoted 21 lines
Quoted 21 lines
drivers/extcon/Kconfig +1 -0
+
 config EXTCON_MAX14577
 	tristate "Maxim MAX14577/77836 EXTCON Support"
drivers/extcon/Kconfig +0 -0
 	depends on MFD_MAX14577
drivers/extcon/Makefile +1 -0
index 261ce4cfe209..d3941a735df3 100644
@@ -11,6 +11,7 @@ obj-$(CONFIG_EXTCON_AXP288)	+= extcon-axp288.o
 obj-$(CONFIG_EXTCON_GPIO)	+= extcon-gpio.o
 obj-$(CONFIG_EXTCON_INTEL_INT3496) += extcon-intel-int3496.o
 obj-$(CONFIG_EXTCON_INTEL_CHT_WC) += extcon-intel-cht-wc.o
+obj-$(CONFIG_EXTCON_INTEL_MRFLD) += extcon-intel-mrfld.o
 obj-$(CONFIG_EXTCON_MAX14577)	+= extcon-max14577.o
 obj-$(CONFIG_EXTCON_MAX3355)	+= extcon-max3355.o
 obj-$(CONFIG_EXTCON_MAX77693)	+= extcon-max77693.o
drivers/extcon/extcon-intel-mrfld.c new file +0 -0
new file mode 100644
index 000000000000..d45db4975b5f
Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 5

Quoted 6 lines
drivers/extcon/extcon-intel-mrfld.c new file +5 -0
@@ -0,0 +1,256 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Extcon driver for Basin Cove PMIC
+ *
+ * Copyright (c) 2018, Intel Corporation.

2019 I suppose :-)

Right.

Quoted 65 lines
Quoted 65 lines
drivers/extcon/extcon-intel-mrfld.c new file +64 -0
+ * Author: Andy Shevchenko <[email protected]>
+ */
+
+#include <linux/extcon-provider.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/intel_soc_pmic.h>
+#include <linux/mfd/intel_soc_pmic_mrfld.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "extcon-intel.h"
+
+#define BCOVE_USBIDCTRL			0x19
+#define BCOVE_USBIDCTRL_ID		BIT(0)
+#define BCOVE_USBIDCTRL_ACA		BIT(1)
+#define BCOVE_USBIDCTRL_ALL	(BCOVE_USBIDCTRL_ID | BCOVE_USBIDCTRL_ACA)
+
+#define BCOVE_USBIDSTS			0x1a
+#define BCOVE_USBIDSTS_GND		BIT(0)
+#define BCOVE_USBIDSTS_RARBRC_MASK	GENMASK(2, 1)
+#define BCOVE_USBIDSTS_RARBRC_SHIFT	1
+#define BCOVE_USBIDSTS_NO_ACA		0
+#define BCOVE_USBIDSTS_R_ID_A		1
+#define BCOVE_USBIDSTS_R_ID_B		2
+#define BCOVE_USBIDSTS_R_ID_C		3
+#define BCOVE_USBIDSTS_FLOAT		BIT(3)
+#define BCOVE_USBIDSTS_SHORT		BIT(4)
+
+#define BCOVE_CHGRIRQ_ALL	(BCOVE_CHGRIRQ_VBUSDET | BCOVE_CHGRIRQ_DCDET | \
+				 BCOVE_CHGRIRQ_BATTDET | BCOVE_CHGRIRQ_USBIDDET)
+
+#define BCOVE_CHGRCTRL0			0x4b
+#define BCOVE_CHGRCTRL0_CHGRRESET	BIT(0)
+#define BCOVE_CHGRCTRL0_EMRGCHREN	BIT(1)
+#define BCOVE_CHGRCTRL0_EXTCHRDIS	BIT(2)
+#define BCOVE_CHGRCTRL0_SWCONTROL	BIT(3)
+#define BCOVE_CHGRCTRL0_TTLCK		BIT(4)
+#define BCOVE_CHGRCTRL0_BIT_5		BIT(5)
+#define BCOVE_CHGRCTRL0_BIT_6		BIT(6)
+#define BCOVE_CHGRCTRL0_CHR_WDT_NOKICK	BIT(7)
+
+struct mrfld_extcon_data {
+	struct device *dev;
+	struct regmap *regmap;
+	struct extcon_dev *edev;
+	unsigned int status;
+	unsigned int id;
+};
+
+static const unsigned int mrfld_extcon_cable[] = {
+	EXTCON_USB,
+	EXTCON_USB_HOST,
+	EXTCON_CHG_USB_SDP,
+	EXTCON_CHG_USB_CDP,
+	EXTCON_CHG_USB_DCP,
+	EXTCON_CHG_USB_ACA,
+	EXTCON_NONE,
+};
+
+static int mrfld_extcon_clear(struct mrfld_extcon_data *data, unsigned int reg,
+			      unsigned int mask)
+{
Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 77

Quoted 8 lines
drivers/extcon/extcon-intel-mrfld.c new file +8 -0
+	return regmap_update_bits(data->regmap, reg, mask, 0x00);
+}
+
+static int mrfld_extcon_set(struct mrfld_extcon_data *data, unsigned int reg,
+			    unsigned int mask)
+{
+	return regmap_update_bits(data->regmap, reg, mask, 0xff);
+}

mrfld_extcon_clear() and mrfld_extcon_set() are just wrapper function for regmap interface. I think that you better to define the meaningful defintion for '0x00' and '0xff' as following:

(just example, you may make the more correct name)
#define INTEL_MRFLD_RESET 0x00
#define INTEL_MRFLD_SET 0xff

And then you better to use the 'regmap_update_bits()' function directly instead of mrfld_extcon_clear/set'.

Also, you should handle the exception hanlding when using regmap function.

Quoted 14 lines
Quoted 14 lines
drivers/extcon/extcon-intel-mrfld.c new file +14 -0
+
+static int mrfld_extcon_get_id(struct mrfld_extcon_data *data)
+{
+	struct regmap *regmap = data->regmap;
+	unsigned int id;
+	bool ground;
+	int ret;
+
+	ret = regmap_read(regmap, BCOVE_USBIDSTS, &id);
+	if (ret)
+		return ret;
+
+	if (id & BCOVE_USBIDSTS_FLOAT)
+		return INTEL_USB_ID_FLOAT;
Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 99

Quoted 8 lines
drivers/extcon/extcon-intel-mrfld.c new file +8 -0
+
+	switch ((id & BCOVE_USBIDSTS_RARBRC_MASK) >> BCOVE_USBIDSTS_RARBRC_SHIFT) {
+	case BCOVE_USBIDSTS_R_ID_A:
+		return INTEL_USB_RID_A;
+	case BCOVE_USBIDSTS_R_ID_B:
+		return INTEL_USB_RID_B;
+	case BCOVE_USBIDSTS_R_ID_C:
+		return INTEL_USB_RID_C;

Please add 'default' statement for exception handling.

Quoted 48 lines
Quoted 48 lines
drivers/extcon/extcon-intel-mrfld.c new file +48 -0
+	}
+
+	/*
+	 * PMIC A0 reports USBIDSTS_GND = 1 for ID_GND,
+	 * but PMIC B0 reports USBIDSTS_GND = 0 for ID_GND.
+	 * Thus we must check this bit at last.
+	 */
+	ground = id & BCOVE_USBIDSTS_GND;
+	switch ('A' + BCOVE_MAJOR(data->id)) {
+	case 'A':
+		return ground ? INTEL_USB_ID_GND : INTEL_USB_ID_FLOAT;
+	case 'B':
+		return ground ? INTEL_USB_ID_FLOAT : INTEL_USB_ID_GND;
+	}
+
+	/* Unknown or unsupported type */
+	return INTEL_USB_ID_FLOAT;
+}
+
+static int mrfld_extcon_role_detect(struct mrfld_extcon_data *data)
+{
+	unsigned int id;
+	bool usb_host;
+	int ret;>> +
+	ret = mrfld_extcon_get_id(data);
+	if (ret < 0)
+		return ret;
+
+	id = ret;
+
+	usb_host = (id == INTEL_USB_ID_GND) || (id == INTEL_USB_RID_A);
+	extcon_set_state_sync(data->edev, EXTCON_USB_HOST, usb_host);
+
+	return 0;
+}
+
+static int mrfld_extcon_cable_detect(struct mrfld_extcon_data *data)
+{
+	struct regmap *regmap = data->regmap;
+	unsigned int status;
+	int ret;
+
+	/*
+	 * It seems SCU firmware clears the content of BCOVE_CHGRIRQ1
+	 * and makes it useless for OS. Instead we compare a previously
+	 * stored status to the current one, provided by BCOVE_SCHGRIRQ1.
+	 */
+	ret = regmap_read(regmap, BCOVE_SCHGRIRQ1, &status);
Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 156

Quoted 8 lines
drivers/extcon/extcon-intel-mrfld.c new file +8 -0
+	if (ret)
+		return ret;
+
+	if (!(status ^ data->status))
+		return -ENODATA;
+
+	if ((status ^ data->status) & BCOVE_CHGRIRQ_USBIDDET)
+		ret = mrfld_extcon_role_detect(data);

This line gets the return value from mrfld_extcon_role_detect(data) without any error handling and then the below line just saves 'status' to 'data->status' regardless of 'ret' value.

I think that you have to handle the error case of
'ret = mrfld_extcon_role_detect(data)'.

Quoted 2 lines

drivers/extcon/extcon-intel-mrfld.c line 157

Quoted 2 lines
drivers/extcon/extcon-intel-mrfld.c new file +2 -0
+
+	data->status = status;

nitpick. better to add one blank line.

Quoted 42 lines
Quoted 42 lines
drivers/extcon/extcon-intel-mrfld.c new file +42 -0
+	return ret;
+}
+
+static irqreturn_t mrfld_extcon_interrupt(int irq, void *dev_id)
+{
+	struct mrfld_extcon_data *data = dev_id;
+	int ret;
+
+	ret = mrfld_extcon_cable_detect(data);
+
+	mrfld_extcon_clear(data, BCOVE_MIRQLVL1, BCOVE_LVL1_CHGR);
+
+	return ret ? IRQ_NONE: IRQ_HANDLED;
+}
+
+static int mrfld_extcon_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct intel_soc_pmic *pmic = dev_get_drvdata(dev->parent);
+	struct regmap *regmap = pmic->regmap;
+	struct mrfld_extcon_data *data;
+	unsigned int id;
+	int irq, ret;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->dev = dev;
+	data->regmap = regmap;
+
+	data->edev = devm_extcon_dev_allocate(dev, mrfld_extcon_cable);
+	if (IS_ERR(data->edev))
+		return -ENOMEM;
+
+	ret = devm_extcon_dev_register(dev, data->edev);
+	if (ret < 0) {
+		dev_err(dev, "can't register extcon device: %d\n", ret);
Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 208

Quoted 8 lines
drivers/extcon/extcon-intel-mrfld.c new file +8 -0
+		return ret;
+	}
+
+	ret = devm_request_threaded_irq(dev, irq, NULL, mrfld_extcon_interrupt,
+					IRQF_ONESHOT | IRQF_SHARED, pdev->name,
+					data);
+	if (ret)
+		return ret;

You better add the error log with dev_err.

Quoted 4 lines

drivers/extcon/extcon-intel-mrfld.c line 212

Quoted 4 lines
drivers/extcon/extcon-intel-mrfld.c new file +4 -0
+
+	ret = regmap_read(regmap, BCOVE_ID, &id);
+	if (ret)
+		return ret;

ditto for error log.

Quoted 7 lines

drivers/extcon/extcon-intel-mrfld.c line 219

Quoted 7 lines
drivers/extcon/extcon-intel-mrfld.c new file +7 -0
+
+	data->id = id;
+
+	mrfld_extcon_set(data, BCOVE_CHGRCTRL0, BCOVE_CHGRCTRL0_SWCONTROL);
+
+	/* Get initial state */
+	mrfld_extcon_role_detect(data);

Please handle the return value for exception handling with log.

Quoted 7 lines

drivers/extcon/extcon-intel-mrfld.c line 226

Quoted 7 lines
drivers/extcon/extcon-intel-mrfld.c new file +7 -0
+
+	mrfld_extcon_clear(data, BCOVE_MIRQLVL1, BCOVE_LVL1_CHGR);
+	mrfld_extcon_clear(data, BCOVE_MCHGRIRQ1, BCOVE_CHGRIRQ_ALL);
+
+	mrfld_extcon_set(data, BCOVE_USBIDCTRL, BCOVE_USBIDCTRL_ALL);
+
+	platform_set_drvdata(pdev, data);

nitpick. better to add one blank line.

Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 234

Quoted 8 lines
drivers/extcon/extcon-intel-mrfld.c new file +8 -0
+	return 0;
+}
+
+static int mrfld_extcon_remove(struct platform_device *pdev)
+{
+	struct mrfld_extcon_data *data = platform_get_drvdata(pdev);
+
+	mrfld_extcon_clear(data, BCOVE_CHGRCTRL0, BCOVE_CHGRCTRL0_SWCONTROL);

nitpick. better to add one blank line.

Quoted 5 lines

drivers/extcon/extcon-intel-mrfld.c line 239

Quoted 5 lines
drivers/extcon/extcon-intel-mrfld.c new file +5 -0
+	return 0;
+}
+
+static const struct platform_device_id mrfld_extcon_id_table[] = {
+	{ .name = "mrfld_bcove_extcon" },

I think that it is not proper to use 'extcon' word for the compatible name because 'extcon' word is linuxium. So, I recommend that you remove the 'extcon' word. Instead, you better to use new word related to h/w.

Quoted 7 lines

drivers/extcon/extcon-intel-mrfld.c line 246

Quoted 7 lines
drivers/extcon/extcon-intel-mrfld.c new file +7 -0
+	{}
+};
+MODULE_DEVICE_TABLE(platform, mrfld_extcon_id_table);
+
+static struct platform_driver mrfld_extcon_driver = {
+	.driver = {
+		.name	= KBUILD_MODNAME,

Where is the definition of KBUILD_MODNAME? Are you missing?

Quoted 9 lines

drivers/extcon/extcon-intel-mrfld.c line 255

Quoted 9 lines
drivers/extcon/extcon-intel-mrfld.c new file +9 -0
+	},
+	.probe		= mrfld_extcon_probe,
+	.remove		= mrfld_extcon_remove,
+	.id_table	= mrfld_extcon_id_table,
+};
+module_platform_driver(mrfld_extcon_driver);
+
+MODULE_AUTHOR("Andy Shevchenko <[email protected]>");
+MODULE_DESCRIPTION("Extcon driver for Basin Cove PMIC");

Add the 'Merrifield' word in front of 'Basin Cove PMIC' as following:
- Merrifield Basic Cove PMIC

Quoted 5 lines
Quoted 4 lines
drivers/extcon/extcon-intel-mrfld.c new file +1 -0
+MODULE_LICENSE("GPL v2");
Signature · 1 line
2.20.1
Signature · 3 lines
Best Regards,
Chanwoo Choi
Samsung Electronics
maintainer
#4 lore raw

Re: [PATCH v1 2/2] extcon: mrfld: Introduce extcon driver for Basin Cove PMIC

Hi Andy,

Quoted 5 lines · Chanwoo Choi

Hi Andy,

Thanks for comment. I add my comments
and then you have to rebase it on latest v5.0-rc1
because the merge conflict happen on v5.0-rc1.

Please rebase the extcon-next branch instead of v5.0-rc1.

Quoted 399 lines · Andy Shevchenko
Quoted 30 lines · Andy Shevchenko
Quoted 1 line

TBD

Oops.
I though I have written it already.

I will wait for other comments today and sent a new version with commit message filled as follows:

On Intel Merrifield the Basin Cove PMIC provides a feature to detect the USB connection type. This driver utilizes the feature in order to support the USB dual role detection.

Quoted 17 lines
---
 drivers/extcon/Kconfig              |   7 +
 drivers/extcon/Makefile             |   1 +
 drivers/extcon/extcon-intel-mrfld.c | 256 ++++++++++++++++++++++++++++
 3 files changed, 264 insertions(+)
 create mode 100644 drivers/extcon/extcon-intel-mrfld.c
drivers/extcon/Kconfig +0 -0
index 8e17149655f0..75349c6cc89e 100644
@@ -60,6 +60,13 @@ config EXTCON_INTEL_CHT_WC
 	  Say Y here to enable extcon support for charger detection / control
 	  on the Intel Cherrytrail Whiskey Cove PMIC.
 
Quoted 7 lines

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 64

Quoted 3 lines
drivers/extcon/Kconfig +2 -0
+config EXTCON_INTEL_MRFLD
 
+	tristate "Intel MErrifield Basin Cove PMIC extcon driver"

ME -> Me (will be fixed)

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 65

Quoted 1 line
drivers/extcon/Kconfig +1 -0
+	depends on INTEL_SOC_PMIC_MRFLD

This driver uses the regmap interface. So, you better to add following dependency?
- select REGMAP_I2C or REGMAP_SPI

But, if 'INTEL_SOC_PMIC_MRFLE' selects already REGMAP_* configuration. It is not necessary.

Quoted 3 lines

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 68

Quoted 3 lines
drivers/extcon/Kconfig +3 -0
+	help
+	  Say Y here to enable extcon support for charger detection / control
+	  on the Intel Merrifiel Basin Cove PMIC.

What is correct word?
- Merrifield? is used on above
- Merrifiel?

Quoted 21 lines
Quoted 21 lines
drivers/extcon/Kconfig +1 -0
+
 config EXTCON_MAX14577
 	tristate "Maxim MAX14577/77836 EXTCON Support"
drivers/extcon/Kconfig +0 -0
 	depends on MFD_MAX14577
drivers/extcon/Makefile +1 -0
index 261ce4cfe209..d3941a735df3 100644
@@ -11,6 +11,7 @@ obj-$(CONFIG_EXTCON_AXP288)	+= extcon-axp288.o
 obj-$(CONFIG_EXTCON_GPIO)	+= extcon-gpio.o
 obj-$(CONFIG_EXTCON_INTEL_INT3496) += extcon-intel-int3496.o
 obj-$(CONFIG_EXTCON_INTEL_CHT_WC) += extcon-intel-cht-wc.o
+obj-$(CONFIG_EXTCON_INTEL_MRFLD) += extcon-intel-mrfld.o
 obj-$(CONFIG_EXTCON_MAX14577)	+= extcon-max14577.o
 obj-$(CONFIG_EXTCON_MAX3355)	+= extcon-max3355.o
 obj-$(CONFIG_EXTCON_MAX77693)	+= extcon-max77693.o
drivers/extcon/extcon-intel-mrfld.c new file +0 -0
new file mode 100644
index 000000000000..d45db4975b5f
Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 5

Quoted 6 lines
drivers/extcon/extcon-intel-mrfld.c new file +5 -0
@@ -0,0 +1,256 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Extcon driver for Basin Cove PMIC
+ *
+ * Copyright (c) 2018, Intel Corporation.

2019 I suppose :-)

Right.

Quoted 65 lines
Quoted 65 lines
drivers/extcon/extcon-intel-mrfld.c new file +64 -0
+ * Author: Andy Shevchenko <[email protected]>
+ */
+
+#include <linux/extcon-provider.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/intel_soc_pmic.h>
+#include <linux/mfd/intel_soc_pmic_mrfld.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "extcon-intel.h"
+
+#define BCOVE_USBIDCTRL			0x19
+#define BCOVE_USBIDCTRL_ID		BIT(0)
+#define BCOVE_USBIDCTRL_ACA		BIT(1)
+#define BCOVE_USBIDCTRL_ALL	(BCOVE_USBIDCTRL_ID | BCOVE_USBIDCTRL_ACA)
+
+#define BCOVE_USBIDSTS			0x1a
+#define BCOVE_USBIDSTS_GND		BIT(0)
+#define BCOVE_USBIDSTS_RARBRC_MASK	GENMASK(2, 1)
+#define BCOVE_USBIDSTS_RARBRC_SHIFT	1
+#define BCOVE_USBIDSTS_NO_ACA		0
+#define BCOVE_USBIDSTS_R_ID_A		1
+#define BCOVE_USBIDSTS_R_ID_B		2
+#define BCOVE_USBIDSTS_R_ID_C		3
+#define BCOVE_USBIDSTS_FLOAT		BIT(3)
+#define BCOVE_USBIDSTS_SHORT		BIT(4)
+
+#define BCOVE_CHGRIRQ_ALL	(BCOVE_CHGRIRQ_VBUSDET | BCOVE_CHGRIRQ_DCDET | \
+				 BCOVE_CHGRIRQ_BATTDET | BCOVE_CHGRIRQ_USBIDDET)
+
+#define BCOVE_CHGRCTRL0			0x4b
+#define BCOVE_CHGRCTRL0_CHGRRESET	BIT(0)
+#define BCOVE_CHGRCTRL0_EMRGCHREN	BIT(1)
+#define BCOVE_CHGRCTRL0_EXTCHRDIS	BIT(2)
+#define BCOVE_CHGRCTRL0_SWCONTROL	BIT(3)
+#define BCOVE_CHGRCTRL0_TTLCK		BIT(4)
+#define BCOVE_CHGRCTRL0_BIT_5		BIT(5)
+#define BCOVE_CHGRCTRL0_BIT_6		BIT(6)
+#define BCOVE_CHGRCTRL0_CHR_WDT_NOKICK	BIT(7)
+
+struct mrfld_extcon_data {
+	struct device *dev;
+	struct regmap *regmap;
+	struct extcon_dev *edev;
+	unsigned int status;
+	unsigned int id;
+};
+
+static const unsigned int mrfld_extcon_cable[] = {
+	EXTCON_USB,
+	EXTCON_USB_HOST,
+	EXTCON_CHG_USB_SDP,
+	EXTCON_CHG_USB_CDP,
+	EXTCON_CHG_USB_DCP,
+	EXTCON_CHG_USB_ACA,
+	EXTCON_NONE,
+};
+
+static int mrfld_extcon_clear(struct mrfld_extcon_data *data, unsigned int reg,
+			      unsigned int mask)
+{
Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 77

Quoted 8 lines
drivers/extcon/extcon-intel-mrfld.c new file +8 -0
+	return regmap_update_bits(data->regmap, reg, mask, 0x00);
+}
+
+static int mrfld_extcon_set(struct mrfld_extcon_data *data, unsigned int reg,
+			    unsigned int mask)
+{
+	return regmap_update_bits(data->regmap, reg, mask, 0xff);
+}

mrfld_extcon_clear() and mrfld_extcon_set() are just wrapper function for regmap interface. I think that you better to define the meaningful defintion for '0x00' and '0xff' as following:

(just example, you may make the more correct name)
#define INTEL_MRFLD_RESET 0x00
#define INTEL_MRFLD_SET 0xff

And then you better to use the 'regmap_update_bits()' function directly instead of mrfld_extcon_clear/set'.

Also, you should handle the exception hanlding when using regmap function.

Quoted 14 lines
Quoted 14 lines
drivers/extcon/extcon-intel-mrfld.c new file +14 -0
+
+static int mrfld_extcon_get_id(struct mrfld_extcon_data *data)
+{
+	struct regmap *regmap = data->regmap;
+	unsigned int id;
+	bool ground;
+	int ret;
+
+	ret = regmap_read(regmap, BCOVE_USBIDSTS, &id);
+	if (ret)
+		return ret;
+
+	if (id & BCOVE_USBIDSTS_FLOAT)
+		return INTEL_USB_ID_FLOAT;
Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 99

Quoted 8 lines
drivers/extcon/extcon-intel-mrfld.c new file +8 -0
+
+	switch ((id & BCOVE_USBIDSTS_RARBRC_MASK) >> BCOVE_USBIDSTS_RARBRC_SHIFT) {
+	case BCOVE_USBIDSTS_R_ID_A:
+		return INTEL_USB_RID_A;
+	case BCOVE_USBIDSTS_R_ID_B:
+		return INTEL_USB_RID_B;
+	case BCOVE_USBIDSTS_R_ID_C:
+		return INTEL_USB_RID_C;

Please add 'default' statement for exception handling.

Quoted 48 lines
Quoted 48 lines
drivers/extcon/extcon-intel-mrfld.c new file +48 -0
+	}
+
+	/*
+	 * PMIC A0 reports USBIDSTS_GND = 1 for ID_GND,
+	 * but PMIC B0 reports USBIDSTS_GND = 0 for ID_GND.
+	 * Thus we must check this bit at last.
+	 */
+	ground = id & BCOVE_USBIDSTS_GND;
+	switch ('A' + BCOVE_MAJOR(data->id)) {
+	case 'A':
+		return ground ? INTEL_USB_ID_GND : INTEL_USB_ID_FLOAT;
+	case 'B':
+		return ground ? INTEL_USB_ID_FLOAT : INTEL_USB_ID_GND;
+	}
+
+	/* Unknown or unsupported type */
+	return INTEL_USB_ID_FLOAT;
+}
+
+static int mrfld_extcon_role_detect(struct mrfld_extcon_data *data)
+{
+	unsigned int id;
+	bool usb_host;
+	int ret;>> +
+	ret = mrfld_extcon_get_id(data);
+	if (ret < 0)
+		return ret;
+
+	id = ret;
+
+	usb_host = (id == INTEL_USB_ID_GND) || (id == INTEL_USB_RID_A);
+	extcon_set_state_sync(data->edev, EXTCON_USB_HOST, usb_host);
+
+	return 0;
+}
+
+static int mrfld_extcon_cable_detect(struct mrfld_extcon_data *data)
+{
+	struct regmap *regmap = data->regmap;
+	unsigned int status;
+	int ret;
+
+	/*
+	 * It seems SCU firmware clears the content of BCOVE_CHGRIRQ1
+	 * and makes it useless for OS. Instead we compare a previously
+	 * stored status to the current one, provided by BCOVE_SCHGRIRQ1.
+	 */
+	ret = regmap_read(regmap, BCOVE_SCHGRIRQ1, &status);
Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 156

Quoted 8 lines
drivers/extcon/extcon-intel-mrfld.c new file +8 -0
+	if (ret)
+		return ret;
+
+	if (!(status ^ data->status))
+		return -ENODATA;
+
+	if ((status ^ data->status) & BCOVE_CHGRIRQ_USBIDDET)
+		ret = mrfld_extcon_role_detect(data);

This line gets the return value from mrfld_extcon_role_detect(data) without any error handling and then the below line just saves 'status' to 'data->status' regardless of 'ret' value.

I think that you have to handle the error case of
'ret = mrfld_extcon_role_detect(data)'.

Quoted 2 lines

drivers/extcon/extcon-intel-mrfld.c line 157

Quoted 2 lines
drivers/extcon/extcon-intel-mrfld.c new file +2 -0
+
+	data->status = status;

nitpick. better to add one blank line.

Quoted 42 lines
Quoted 42 lines
drivers/extcon/extcon-intel-mrfld.c new file +42 -0
+	return ret;
+}
+
+static irqreturn_t mrfld_extcon_interrupt(int irq, void *dev_id)
+{
+	struct mrfld_extcon_data *data = dev_id;
+	int ret;
+
+	ret = mrfld_extcon_cable_detect(data);
+
+	mrfld_extcon_clear(data, BCOVE_MIRQLVL1, BCOVE_LVL1_CHGR);
+
+	return ret ? IRQ_NONE: IRQ_HANDLED;
+}
+
+static int mrfld_extcon_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct intel_soc_pmic *pmic = dev_get_drvdata(dev->parent);
+	struct regmap *regmap = pmic->regmap;
+	struct mrfld_extcon_data *data;
+	unsigned int id;
+	int irq, ret;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->dev = dev;
+	data->regmap = regmap;
+
+	data->edev = devm_extcon_dev_allocate(dev, mrfld_extcon_cable);
+	if (IS_ERR(data->edev))
+		return -ENOMEM;
+
+	ret = devm_extcon_dev_register(dev, data->edev);
+	if (ret < 0) {
+		dev_err(dev, "can't register extcon device: %d\n", ret);
Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 208

Quoted 8 lines
drivers/extcon/extcon-intel-mrfld.c new file +8 -0
+		return ret;
+	}
+
+	ret = devm_request_threaded_irq(dev, irq, NULL, mrfld_extcon_interrupt,
+					IRQF_ONESHOT | IRQF_SHARED, pdev->name,
+					data);
+	if (ret)
+		return ret;

You better add the error log with dev_err.

Quoted 4 lines

drivers/extcon/extcon-intel-mrfld.c line 212

Quoted 4 lines
drivers/extcon/extcon-intel-mrfld.c new file +4 -0
+
+	ret = regmap_read(regmap, BCOVE_ID, &id);
+	if (ret)
+		return ret;

ditto for error log.

Quoted 7 lines

drivers/extcon/extcon-intel-mrfld.c line 219

Quoted 7 lines
drivers/extcon/extcon-intel-mrfld.c new file +7 -0
+
+	data->id = id;
+
+	mrfld_extcon_set(data, BCOVE_CHGRCTRL0, BCOVE_CHGRCTRL0_SWCONTROL);
+
+	/* Get initial state */
+	mrfld_extcon_role_detect(data);

Please handle the return value for exception handling with log.

Quoted 7 lines

drivers/extcon/extcon-intel-mrfld.c line 226

Quoted 7 lines
drivers/extcon/extcon-intel-mrfld.c new file +7 -0
+
+	mrfld_extcon_clear(data, BCOVE_MIRQLVL1, BCOVE_LVL1_CHGR);
+	mrfld_extcon_clear(data, BCOVE_MCHGRIRQ1, BCOVE_CHGRIRQ_ALL);
+
+	mrfld_extcon_set(data, BCOVE_USBIDCTRL, BCOVE_USBIDCTRL_ALL);
+
+	platform_set_drvdata(pdev, data);

nitpick. better to add one blank line.

Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 234

Quoted 8 lines
drivers/extcon/extcon-intel-mrfld.c new file +8 -0
+	return 0;
+}
+
+static int mrfld_extcon_remove(struct platform_device *pdev)
+{
+	struct mrfld_extcon_data *data = platform_get_drvdata(pdev);
+
+	mrfld_extcon_clear(data, BCOVE_CHGRCTRL0, BCOVE_CHGRCTRL0_SWCONTROL);

nitpick. better to add one blank line.

Quoted 5 lines

drivers/extcon/extcon-intel-mrfld.c line 239

Quoted 5 lines
drivers/extcon/extcon-intel-mrfld.c new file +5 -0
+	return 0;
+}
+
+static const struct platform_device_id mrfld_extcon_id_table[] = {
+	{ .name = "mrfld_bcove_extcon" },

I think that it is not proper to use 'extcon' word for the compatible name because 'extcon' word is linuxium. So, I recommend that you remove the 'extcon' word. Instead, you better to use new word related to h/w.

Quoted 7 lines

drivers/extcon/extcon-intel-mrfld.c line 246

Quoted 7 lines
drivers/extcon/extcon-intel-mrfld.c new file +7 -0
+	{}
+};
+MODULE_DEVICE_TABLE(platform, mrfld_extcon_id_table);
+
+static struct platform_driver mrfld_extcon_driver = {
+	.driver = {
+		.name	= KBUILD_MODNAME,

Where is the definition of KBUILD_MODNAME? Are you missing?

Quoted 9 lines

drivers/extcon/extcon-intel-mrfld.c line 255

Quoted 9 lines
drivers/extcon/extcon-intel-mrfld.c new file +9 -0
+	},
+	.probe		= mrfld_extcon_probe,
+	.remove		= mrfld_extcon_remove,
+	.id_table	= mrfld_extcon_id_table,
+};
+module_platform_driver(mrfld_extcon_driver);
+
+MODULE_AUTHOR("Andy Shevchenko <[email protected]>");
+MODULE_DESCRIPTION("Extcon driver for Basin Cove PMIC");

Add the 'Merrifield' word in front of 'Basin Cove PMIC' as following:
- Merrifield Basic Cove PMIC

Quoted 5 lines
Quoted 4 lines
drivers/extcon/extcon-intel-mrfld.c new file +1 -0
+MODULE_LICENSE("GPL v2");
Signature · 1 line
2.20.1
Signature · 3 lines
Best Regards,
Chanwoo Choi
Samsung Electronics
#5 lore raw

Re: [PATCH v1 2/2] extcon: mrfld: Introduce extcon driver for Basin Cove PMIC

In reply to Chanwoo Choi
Quoted 3 lines · Chanwoo Choi

Thanks for comment. I add my comments
and then you have to rebase it on latest v5.0-rc1
because the merge conflict happen on v5.0-rc1.

Thanks for review, see my answers below. Non-answered items will be fixed accordingly.

Quoted 6 lines
Quoted 6 lines

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 64

Quoted 3 lines
drivers/extcon/Kconfig +2 -0
+config EXTCON_INTEL_MRFLD
 
+	tristate "Intel MErrifield Basin Cove PMIC extcon driver"

ME -> Me (will be fixed)

Quoted 6 lines
Quoted 1 line

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 65

Quoted 1 line
drivers/extcon/Kconfig +1 -0
+	depends on INTEL_SOC_PMIC_MRFLD

This driver uses the regmap interface. So, you better to add following dependency?

- select REGMAP_I2C or REGMAP_SPI

None of them fits this or MFD driver. See below.

Quoted 2 lines

But, if 'INTEL_SOC_PMIC_MRFLE' selects already REGMAP_* configuration. It is not necessary.

https://lore.kernel.org/lkml/[email protected]/

It selects REGMAP_IRQ which selects necessary bits from regmap API.

Quoted 7 lines
Quoted 3 lines

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 68

Quoted 3 lines
drivers/extcon/Kconfig +3 -0
+	help
+	  Say Y here to enable extcon support for charger detection / control
+	  on the Intel Merrifiel Basin Cove PMIC.

What is correct word?
- Merrifield? is used on above
- Merrifiel?

Merrifield is a correct one. Thanks for spotting this.

Quoted 10 lines
Quoted 5 lines

drivers/extcon/extcon-intel-mrfld.c line 77

Quoted 5 lines
drivers/extcon/extcon-intel-mrfld.c new file +5 -0
+static int mrfld_extcon_set(struct mrfld_extcon_data *data, unsigned int reg,
+			    unsigned int mask)
+{
+	return regmap_update_bits(data->regmap, reg, mask, 0xff);
+}

mrfld_extcon_clear() and mrfld_extcon_set() are just wrapper function for regmap interface. I think that you better to define the meaningful defintion for '0x00' and '0xff' as following:

Quoted 3 lines

(just example, you may make the more correct name)
#define INTEL_MRFLD_RESET 0x00
#define INTEL_MRFLD_SET 0xff

It makes a little sense here, the idea is to reduce parameters.

I could ideally write
(..., mask, ~mask) for clear
and
(..., mask, mask) for set

Quoted 2 lines

And then you better to use the 'regmap_update_bits()' function directly instead of mrfld_extcon_clear/set'.

It will bring duplication of long definitions and reduce readability of the code.

Quoted 18 lines
Quoted 6 lines
Quoted 6 lines
drivers/extcon/extcon-intel-mrfld.c new file +6 -0
+	/*
+	 * It seems SCU firmware clears the content of BCOVE_CHGRIRQ1
+	 * and makes it useless for OS. Instead we compare a previously
+	 * stored status to the current one, provided by BCOVE_SCHGRIRQ1.
+	 */
+	ret = regmap_read(regmap, BCOVE_SCHGRIRQ1, &status);
Quoted 8 lines

drivers/extcon/extcon-intel-mrfld.c line 156

Quoted 8 lines
drivers/extcon/extcon-intel-mrfld.c new file +8 -0
+	if (ret)
+		return ret;
+
+	if (!(status ^ data->status))
+		return -ENODATA;
+
+	if ((status ^ data->status) & BCOVE_CHGRIRQ_USBIDDET)
+		ret = mrfld_extcon_role_detect(data);

This line gets the return value from mrfld_extcon_role_detect(data) without any error handling and then the below line just saves 'status' to 'data->status' regardless of 'ret' value.

Quoted 2 lines

I think that you have to handle the error case of
'ret = mrfld_extcon_role_detect(data)'.

I'm not sure of the consequences of such change.
I will give it some tests, and then will proceed accordingly.

Quoted 3 lines
Quoted 1 line

drivers/extcon/extcon-intel-mrfld.c line 246

Quoted 1 line
drivers/extcon/extcon-intel-mrfld.c new file +1 -0
+		.name	= KBUILD_MODNAME,

Where is the definition of KBUILD_MODNAME? Are you missing?

In the Makefile.
Nothing is missed here.

But I could put its content explicitly here.

Signature · 2 lines
With Best Regards,
Andy Shevchenko
maintainer
#6 lore raw

Re: [PATCH v1 2/2] extcon: mrfld: Introduce extcon driver for Basin Cove PMIC

Hi Andy,

Quoted 22 lines · Andy Shevchenko
Quoted 3 lines · Chanwoo Choi

Thanks for comment. I add my comments
and then you have to rebase it on latest v5.0-rc1
because the merge conflict happen on v5.0-rc1.

Thanks for review, see my answers below. Non-answered items will be fixed accordingly.

Quoted 6 lines
Quoted 6 lines

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 64

Quoted 3 lines
drivers/extcon/Kconfig +2 -0
+config EXTCON_INTEL_MRFLD
 
+	tristate "Intel MErrifield Basin Cove PMIC extcon driver"

ME -> Me (will be fixed)

Quoted 6 lines
Quoted 1 line

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 65

Quoted 1 line
drivers/extcon/Kconfig +1 -0
+	depends on INTEL_SOC_PMIC_MRFLD

This driver uses the regmap interface. So, you better to add following dependency?

- select REGMAP_I2C or REGMAP_SPI

Quoted 8 lines

None of them fits this or MFD driver. See below.

Quoted 2 lines

But, if 'INTEL_SOC_PMIC_MRFLE' selects already REGMAP_* configuration. It is not necessary.

https://lore.kernel.org/lkml/[email protected]/

It selects REGMAP_IRQ which selects necessary bits from regmap API.

OK.

Quoted 32 lines
Quoted 8 lines
Quoted 4 lines

drivers/extcon/Kconfig config EXTCON_INTEL_CHT_WC · line 68

Quoted 4 lines
drivers/extcon/Kconfig +3 -0
+	help
+	  Say Y here to enable extcon support for charger detection / control
+	  on the Intel Merrifiel Basin Cove PMIC.

What is correct word?
- Merrifield? is used on above
- Merrifiel?

Merrifield is a correct one. Thanks for spotting this.

Quoted 10 lines
Quoted 5 lines

drivers/extcon/extcon-intel-mrfld.c line 77

Quoted 5 lines
drivers/extcon/extcon-intel-mrfld.c new file +5 -0
+static int mrfld_extcon_set(struct mrfld_extcon_data *data, unsigned int reg,
+			    unsigned int mask)
+{
+	return regmap_update_bits(data->regmap, reg, mask, 0xff);
+}

mrfld_extcon_clear() and mrfld_extcon_set() are just wrapper function for regmap interface. I think that you better to define the meaningful defintion for '0x00' and '0xff' as following:

Quoted 3 lines

(just example, you may make the more correct name)
#define INTEL_MRFLD_RESET 0x00
#define INTEL_MRFLD_SET 0xff

It makes a little sense here, the idea is to reduce parameters.

I could ideally write
(..., mask, ~mask) for clear
and
(..., mask, mask) for set

Quoted 5 lines
Quoted 2 lines

And then you better to use the 'regmap_update_bits()' function directly instead of mrfld_extcon_clear/set'.

It will bring duplication of long definitions and reduce readability of the code.

Actually, it is not critical issue. If you don't agree my comments, you keep your style on next version. I have no any strong objection.

Quoted 19 lines
Quoted 19 lines
Quoted 15 lines
Quoted 5 lines
drivers/extcon/extcon-intel-mrfld.c new file +4 -0
+	/*
+	 * It seems SCU firmware clears the content of BCOVE_CHGRIRQ1
+	 * and makes it useless for OS. Instead we compare a previously
+	 * stored status to the current one, provided by BCOVE_SCHGRIRQ1.

drivers/extcon/extcon-intel-mrfld.c line 156

Quoted 10 lines
drivers/extcon/extcon-intel-mrfld.c new file +10 -0
+	 */
+	ret = regmap_read(regmap, BCOVE_SCHGRIRQ1, &status);
+	if (ret)
+		return ret;
+
+	if (!(status ^ data->status))
+		return -ENODATA;
+
+	if ((status ^ data->status) & BCOVE_CHGRIRQ_USBIDDET)
+		ret = mrfld_extcon_role_detect(data);

This line gets the return value from mrfld_extcon_role_detect(data) without any error handling and then the below line just saves 'status' to 'data->status' regardless of 'ret' value.

Quoted 5 lines
Quoted 2 lines

I think that you have to handle the error case of
'ret = mrfld_extcon_role_detect(data)'.

I'm not sure of the consequences of such change.
I will give it some tests, and then will proceed accordingly.

OK. Thanks.

Quoted 9 lines
Quoted 4 lines
Quoted 2 lines

drivers/extcon/extcon-intel-mrfld.c line 246

Quoted 2 lines
drivers/extcon/extcon-intel-mrfld.c new file +1 -0
+		.name	= KBUILD_MODNAME,

Where is the definition of KBUILD_MODNAME? Are you missing?

In the Makefile.
Nothing is missed here.

But I could put its content explicitly here.

OK. Thanks.

Quoted 1 line
Signature · 3 lines
Best Regards,
Chanwoo Choi
Samsung Electronics
maintainer
#7 lore raw
In reply to Andy Shevchenko

Hi,

Looks good to me. But just there is minor one comment as following:
- 2018 -> 2019

Quoted 84 lines · Andy Shevchenko

We are going to use some definitions in the other Intel extcon drivers, thus, split out them to a common header file.

---
 drivers/extcon/extcon-intel-cht-wc.c | 21 +++++++--------------
 drivers/extcon/extcon-intel.h        | 20 ++++++++++++++++++++
 2 files changed, 27 insertions(+), 14 deletions(-)
 create mode 100644 drivers/extcon/extcon-intel.h
drivers/extcon/extcon-intel-cht-wc.c +7 -14
index 5ef215297101..110bd38a4d24 100644
@@ -17,6 +17,8 @@
 #include <linux/regmap.h>
 #include <linux/slab.h>
 
+#include "extcon-intel.h"
+
 #define CHT_WC_PHYCTRL			0x5e07
 
 #define CHT_WC_CHGRCTRL0		0x5e16
@@ -65,15 +67,6 @@
 #define CHT_WC_VBUS_GPIO_CTLO_DRV_OD	BIT(4)
 #define CHT_WC_VBUS_GPIO_CTLO_DIR_OUT	BIT(5)
 
-enum cht_wc_usb_id {
-	USB_ID_OTG,
-	USB_ID_GND,
-	USB_ID_FLOAT,
-	USB_RID_A,
-	USB_RID_B,
-	USB_RID_C,
-};
-
 enum cht_wc_mux_select {
 	MUX_SEL_PMIC = 0,
 	MUX_SEL_SOC,
@@ -101,9 +94,9 @@ static int cht_wc_extcon_get_id(struct cht_wc_extcon_data *ext, int pwrsrc_sts)
 {
 	switch ((pwrsrc_sts & CHT_WC_PWRSRC_USBID_MASK) >> CHT_WC_PWRSRC_USBID_SHIFT) {
 	case CHT_WC_PWRSRC_RID_GND:
-		return USB_ID_GND;
+		return INTEL_USB_ID_GND;
 	case CHT_WC_PWRSRC_RID_FLOAT:
-		return USB_ID_FLOAT;
+		return INTEL_USB_ID_FLOAT;
 	case CHT_WC_PWRSRC_RID_ACA:
 	default:
 		/*
@@ -111,7 +104,7 @@ static int cht_wc_extcon_get_id(struct cht_wc_extcon_data *ext, int pwrsrc_sts)
 		 * the USBID GPADC channel here and determine ACA role
 		 * based on that.
 		 */
-		return USB_ID_FLOAT;
+		return INTEL_USB_ID_FLOAT;
 	}
 }
 
@@ -221,7 +214,7 @@ static void cht_wc_extcon_pwrsrc_event(struct cht_wc_extcon_data *ext)
 	}
 
 	id = cht_wc_extcon_get_id(ext, pwrsrc_sts);
-	if (id == USB_ID_GND) {
+	if (id == INTEL_USB_ID_GND) {
 		/* The 5v boost causes a false VBUS / SDP detect, skip */
 		goto charger_det_done;
 	}
@@ -248,7 +241,7 @@ static void cht_wc_extcon_pwrsrc_event(struct cht_wc_extcon_data *ext)
 		ext->previous_cable = cable;
 	}
 
-	ext->usb_host = ((id == USB_ID_GND) || (id == USB_RID_A));
+	ext->usb_host = ((id == INTEL_USB_ID_GND) || (id == INTEL_USB_RID_A));
 	extcon_set_state_sync(ext->edev, EXTCON_USB_HOST, ext->usb_host);
 }
 
drivers/extcon/extcon-intel.h new file +0 -0
new file mode 100644
index 000000000000..455986b2b004

drivers/extcon/extcon-intel.h line 5

Quoted 5 lines
drivers/extcon/extcon-intel.h new file +5 -0
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Header file for Intel extcon hardware
+ *
+ * Copyright (C) 2018 Intel Corporation. All rights reserved.

2018 -> 2019

Quoted 16 lines
drivers/extcon/extcon-intel.h new file +15 -0
+ */
+
+#ifndef __EXTCON_INTEL_H__
+#define __EXTCON_INTEL_H__
+
+enum extcon_intel_usb_id {
+	INTEL_USB_ID_OTG,
+	INTEL_USB_ID_GND,
+	INTEL_USB_ID_FLOAT,
+	INTEL_USB_RID_A,
+	INTEL_USB_RID_B,
+	INTEL_USB_RID_C,
+};
+
+#endif	/* __EXTCON_INTEL_H__ */
Signature · 3 lines
Best Regards,
Chanwoo Choi
Samsung Electronics