drm/i915: Ensure minimum CDCLK requirement for audio
Subsystems (2)
v6 cover drm/i915: Ensure minimum CDCLK requirement for audio
This replaces [1] and [2]. The main changes since then:
- A device link between i915 and HDA (added meanwhile as a separate change).
- Split the CDCLK change to happen before or after any updates to the pipe depending on whether we're increasing or decreasing CDCLK.
- Wait for vblank after an optimized CDCLK update.
Abhay confirmed that the patchset fixes the audio issues his team saw due to too low CDCLK.
[1] https://patchwork.freedesktop.org/patch/230817/?series=42459&rev=7
[2] https://patchwork.freedesktop.org/series/48763/
Ville Syrjälä (2):
drm/i915: Force 2*96 MHz cdclk on glk/cnl when audio power is enabled drm/i915: Skip modeset for cdclk changes if possible
drivers/gpu/drm/i915/i915_drv.h | 6 +- drivers/gpu/drm/i915/i915_reg.h | 3 +- drivers/gpu/drm/i915/intel_audio.c | 68 ++++++++++++- drivers/gpu/drm/i915/intel_cdclk.c | 185 +++++++++++++++++++++++++---------- drivers/gpu/drm/i915/intel_display.c | 48 ++++++++- drivers/gpu/drm/i915/intel_drv.h | 18 +++- 6 files changed, 268 insertions(+), 60 deletions(-)
Signature · 5 lines
2.13.2 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 1/2 drm/i915: Force 2*96 MHz cdclk on glk/cnl when audio power is enabled
From: Ville Syrjälä <[email protected]>
CDCLK has to be at least twice the BLCK regardless of audio. Audio driver has to probe using this hook and increase the clock even in absence of any display.
v2: Use atomic refcount for get_power, put_power so that we can
call each once(Abhay).
v3: Reset power well 2 to avoid any transaction on iDisp link
during cdclk change(Abhay).
v4: Remove Power well 2 reset workaround(Ville).
v5: Remove unwanted Power well 2 register defined in v4(Abhay). v6:
- Use a dedicated flag instead of state->modeset for min CDCLK changes
- Make get/put audio power domain symmetric
- Rebased on top of intel_wakref tracking changes.
--- drivers/gpu/drm/i915/i915_drv.h | 3 ++ drivers/gpu/drm/i915/intel_audio.c | 64 ++++++++++++++++++++++++++++++++++-- drivers/gpu/drm/i915/intel_cdclk.c | 30 ++++++----------- drivers/gpu/drm/i915/intel_display.c | 9 ++++- drivers/gpu/drm/i915/intel_drv.h | 3 ++ 5 files changed, 86 insertions(+), 23 deletions(-)
drivers/gpu/drm/i915/i915_drv.h +3 -0
@@ -1624,6 +1624,8 @@ struct drm_i915_private {struct intel_cdclk_state actual;/* The current hardware cdclk state */ struct intel_cdclk_state hw; + +int force_min_cdclk; } cdclk;/**
@@ -1743,6 +1745,7 @@ struct drm_i915_private {* */ struct mutex av_mutex; +int audio_power_refcount;struct {struct mutex mutex;
drivers/gpu/drm/i915/intel_audio.c +62 -2
80 lines not on this page · raw message
drivers/gpu/drm/i915/intel_cdclk.c +10 -20
@@ -2187,19 +2187,8 @@ int intel_crtc_compute_min_cdclk(const struct intel_crtc_state *crtc_state)/* * According to BSpec, "The CD clock frequency must be at least twice * the frequency of the Azalia BCLK." and BCLK is 96 MHz by default. -* -* FIXME: Check the actual, not default, BCLK being used. -* -* FIXME: This does not depend on ->has_audio because the higher CDCLK -* is required for audio probe, also when there are no audio capable -* displays connected at probe time. This leads to unnecessarily high -* CDCLK when audio is not required. -* -* FIXME: This limit is only applied when there are displays connected -* at probe time. If we probe without displays, we'll still end up using -* the platform minimum CDCLK, failing audio probe. */ -if (INTEL_GEN (dev_priv) >=9 ) +if (crtc_state->has_audio &&INTEL_GEN (dev_priv) >=9 ) min_cdclk =max (2 *96000 , min_cdclk);/*
@@ -2239,7 +2228,7 @@ static int intel_compute_min_cdclk(struct drm_atomic_state *state) intel_state->min_cdclk[i] = min_cdclk; } - min_cdclk =0 ; + min_cdclk = intel_state->cdclk.force_min_cdclk;for_each_pipe (dev_priv, pipe) min_cdclk =max (intel_state->min_cdclk[pipe], min_cdclk);
@@ -2300,7 +2289,8 @@ static int vlv_modeset_calc_cdclk(struct drm_atomic_state *state)vlv_calc_voltage_level (dev_priv, cdclk);if (!intel_state->active_crtcs) { - cdclk =vlv_calc_cdclk (dev_priv,0 ); + cdclk =vlv_calc_cdclk (dev_priv, + intel_state->cdclk.force_min_cdclk); intel_state->cdclk.actual.cdclk = cdclk; intel_state->cdclk.actual.voltage_level =
@@ -2333,7 +2323,7 @@ static int bdw_modeset_calc_cdclk(struct drm_atomic_state *state)bdw_calc_voltage_level (cdclk);if (!intel_state->active_crtcs) { - cdclk =bdw_calc_cdclk (0 ); + cdclk =bdw_calc_cdclk (intel_state->cdclk.force_min_cdclk); intel_state->cdclk.actual.cdclk = cdclk; intel_state->cdclk.actual.voltage_level =
@@ -2405,7 +2395,7 @@ static int skl_modeset_calc_cdclk(struct drm_atomic_state *state)skl_calc_voltage_level (cdclk);if (!intel_state->active_crtcs) { - cdclk =skl_calc_cdclk (0 , vco); + cdclk =skl_calc_cdclk (intel_state->cdclk.force_min_cdclk, vco); intel_state->cdclk.actual.vco = vco; intel_state->cdclk.actual.cdclk = cdclk;
@@ -2444,10 +2434,10 @@ static int bxt_modeset_calc_cdclk(struct drm_atomic_state *state)if (!intel_state->active_crtcs) {if (IS_GEMINILAKE (dev_priv)) { - cdclk =glk_calc_cdclk (0 ); + cdclk =glk_calc_cdclk (intel_state->cdclk.force_min_cdclk); vco =glk_de_pll_vco (dev_priv, cdclk); }else { - cdclk =bxt_calc_cdclk (0 ); + cdclk =bxt_calc_cdclk (intel_state->cdclk.force_min_cdclk); vco =bxt_de_pll_vco (dev_priv, cdclk); }
@@ -2483,7 +2473,7 @@ static int cnl_modeset_calc_cdclk(struct drm_atomic_state *state) cnl_compute_min_voltage_level(intel_state));if (!intel_state->active_crtcs) { - cdclk =cnl_calc_cdclk (0 ); + cdclk =cnl_calc_cdclk (intel_state->cdclk.force_min_cdclk); vco =cnl_cdclk_pll_vco (dev_priv, cdclk); intel_state->cdclk.actual.vco = vco;
@@ -2519,7 +2509,7 @@ static int icl_modeset_calc_cdclk(struct drm_atomic_state *state) cnl_compute_min_voltage_level(intel_state));if (!intel_state->active_crtcs) { - cdclk =icl_calc_cdclk (0 , ref); + cdclk =icl_calc_cdclk (intel_state->cdclk.force_min_cdclk, ref); vco =icl_calc_cdclk_pll_vco (dev_priv, cdclk); intel_state->cdclk.actual.vco = vco;
drivers/gpu/drm/i915/intel_display.c +8 -1
@@ -12973,6 +12973,11 @@ static int intel_modeset_checks(struct drm_atomic_state *state)return -EINVAL ; } +/* keep the current setting */ +if (!intel_state->cdclk.force_min_cdclk_changed) + intel_state->cdclk.force_min_cdclk = + dev_priv->cdclk.force_min_cdclk; + intel_state->modeset = true; intel_state->active_crtcs = dev_priv->active_crtcs; intel_state->cdclk.logical = dev_priv->cdclk.logical;
@@ -13068,7 +13073,7 @@ static int intel_atomic_check(struct drm_device *dev,struct drm_crtc *crtc;struct drm_crtc_state *old_crtc_state, *crtc_state;int ret, i; -bool any_ms = false; +bool any_ms = intel_state->cdclk.force_min_cdclk_changed;/* Catch I915_MODE_FLAG_INHERITED */ for_each_oldnew_crtc_in_state(state, crtc, old_crtc_state,
@@ -13660,6 +13665,8 @@ static int intel_atomic_commit(struct drm_device *dev, dev_priv->active_crtcs = intel_state->active_crtcs; dev_priv->cdclk.logical = intel_state->cdclk.logical; dev_priv->cdclk.actual = intel_state->cdclk.actual; + dev_priv->cdclk.force_min_cdclk = + intel_state->cdclk.force_min_cdclk; }drm_atomic_state_get (state);
drivers/gpu/drm/i915/intel_drv.h +3 -0
@@ -556,6 +556,9 @@ struct intel_atomic_state {* state only when all crtc's are DPMS off. */ struct intel_cdclk_state actual; + +int force_min_cdclk; +bool force_min_cdclk_changed; } cdclk;bool dpll_set, modeset;
Signature · 6 lines
2.13.2 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 2/2 drm/i915: Skip modeset for cdclk changes if possible
In reply to Imre DeakFrom: Ville Syrjälä <[email protected]>
If we have only a single active pipe and the cdclk change only requires the cd2x divider to be updated bxt+ can do the update with forcing a full modeset on the pipe. Try to hook that up.
v2:
- Wait for vblank after an optimized CDCLK change.
- Avoid optimization if the pipe needs a modeset (or was disabled).
- Split CDCLK change to a pre/post plane update step.
--- drivers/gpu/drm/i915/i915_drv.h | 3 +- drivers/gpu/drm/i915/i915_reg.h | 3 +- drivers/gpu/drm/i915/intel_cdclk.c | 155 ++++++++++++++++++++++++++++------- drivers/gpu/drm/i915/intel_display.c | 39 ++++++++- drivers/gpu/drm/i915/intel_drv.h | 15 +++- 5 files changed, 178 insertions(+), 37 deletions(-)
drivers/gpu/drm/i915/i915_drv.h +2 -1
@@ -277,7 +277,8 @@ struct drm_i915_display_funcs {void (*get_cdclk)(struct drm_i915_private *dev_priv,struct intel_cdclk_state *cdclk_state);void (*set_cdclk)(struct drm_i915_private *dev_priv, -const struct intel_cdclk_state *cdclk_state); +const struct intel_cdclk_state *cdclk_state, +enum pipe pipe);int (*get_fifo_size)(struct drm_i915_private *dev_priv,enum i9xx_plane_id i9xx_plane);int (*compute_pipe_wm)(struct intel_crtc_state *cstate);
drivers/gpu/drm/i915/i915_reg.h +2 -1
@@ -9521,7 +9521,8 @@ enum skl_power_gate {#define BXT_CDCLK_CD2X_PIPE (pipe) ((pipe) << 20)#define CDCLK_DIVMUX_CD_OVERRIDE (1 << 19)#define BXT_CDCLK_CD2X_PIPE_NONE BXT_CDCLK_CD2X_PIPE(3) -#define ICL_CDCLK_CD2X_PIPE_NONE (7 << 19) +#define ICL_CDCLK_CD2X_PIPE (pipe) ((pipe) << 19) +#define ICL_CDCLK_CD2X_PIPE_NONE ICL_CDCLK_CD2X_PIPE(7)#define BXT_CDCLK_SSA_PRECHARGE_ENABLE (1 << 16)#define CDCLK_FREQ_DECIMAL_MASK (0x7ff)
drivers/gpu/drm/i915/intel_cdclk.c +125 -30
302 lines not on this page · raw message
drivers/gpu/drm/i915/intel_display.c +36 -3
@@ -12982,6 +12982,7 @@ static int intel_modeset_checks(struct drm_atomic_state *state) intel_state->active_crtcs = dev_priv->active_crtcs; intel_state->cdclk.logical = dev_priv->cdclk.logical; intel_state->cdclk.actual = dev_priv->cdclk.actual; + intel_state->cdclk.pipe =INVALID_PIPE ;for_each_oldnew_crtc_in_state (state, crtc, old_crtc_state, new_crtc_state, i) {if (new_crtc_state->active)
@@ -13001,6 +13002,8 @@ static int intel_modeset_checks(struct drm_atomic_state *state)* adjusted_mode bits in the crtc directly. */ if (dev_priv->display.modeset_calc_cdclk) { +enum pipe pipe; + ret = dev_priv->display.modeset_calc_cdclk (state);if (ret <0 )return ret;
@@ -13017,12 +13020,36 @@ static int intel_modeset_checks(struct drm_atomic_state *state)return ret; } +if (is_power_of_2 (intel_state->active_crtcs)) { +struct drm_crtc *crtc; +struct drm_crtc_state *crtc_state; + + pipe =ilog2 (intel_state->active_crtcs); + crtc = &intel_get_crtc_for_pipe (dev_priv, pipe)->base; + crtc_state =drm_atomic_get_new_crtc_state (state, crtc); +if (crtc_state &&needs_modeset (crtc_state)) + pipe =INVALID_PIPE ; + }else { + pipe =INVALID_PIPE ; + } +/* All pipes must be switched off while we change the cdclk. */ -if (intel_cdclk_needs_modeset (&dev_priv->cdclk.actual, - &intel_state->cdclk.actual)) { +if (pipe !=INVALID_PIPE && +intel_cdclk_needs_cd2x_update (dev_priv, + &dev_priv->cdclk.actual, + &intel_state->cdclk.actual)) { + ret =intel_lock_all_pipes (state); +if (ret <0 ) +return ret; + + intel_state->cdclk.pipe = pipe; + }else if (intel_cdclk_needs_modeset (&dev_priv->cdclk.actual, + &intel_state->cdclk.actual)) { ret =intel_modeset_all_pipes (state);if (ret <0 )return ret; + + intel_state->cdclk.pipe =INVALID_PIPE ; } DRM_DEBUG_KMS("New cdclk calculated to be logical %u kHz, actual %u kHz\n",
@@ -13433,7 +13460,9 @@ static void intel_atomic_commit_tail(struct drm_atomic_state *state)if (intel_state->modeset) {drm_atomic_helper_update_legacy_modeset_state (state->dev, state); -intel_set_cdclk (dev_priv, &dev_priv->cdclk.actual); +intel_set_cdclk_pre_plane_update (dev_priv, + &dev_priv->cdclk.actual, + intel_state->cdclk.pipe);/* * SKL workaround: bspec recommends we disable the SAGV when we
@@ -13462,6 +13491,10 @@ static void intel_atomic_commit_tail(struct drm_atomic_state *state)/* Now enable the clocks, plane, pipe, and connectors that we set up. */ dev_priv->display.update_crtcs (state); +intel_set_cdclk_post_plane_update (dev_priv, + &dev_priv->cdclk.actual, + intel_state->cdclk.pipe); +/* FIXME: We should call drm_atomic_helper_commit_hw_done() here * already, but still need the state for the delayed optimization. To * fix this:
drivers/gpu/drm/i915/intel_drv.h +13 -2
@@ -559,6 +559,8 @@ struct intel_atomic_state {int force_min_cdclk;bool force_min_cdclk_changed; +/* pipe to which cd2x update is synchronized */ +enum pipe pipe; } cdclk;bool dpll_set, modeset;
@@ -1694,12 +1696,21 @@ void intel_init_cdclk_hooks(struct drm_i915_private *dev_priv);void intel_update_max_cdclk (struct drm_i915_private *dev_priv);void intel_update_cdclk (struct drm_i915_private *dev_priv);void intel_update_rawclk (struct drm_i915_private *dev_priv); +bool intel_cdclk_needs_cd2x_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *a, +const struct intel_cdclk_state *b);bool intel_cdclk_needs_modeset (const struct intel_cdclk_state *a,const struct intel_cdclk_state *b);bool intel_cdclk_changed (const struct intel_cdclk_state *a,const struct intel_cdclk_state *b); -void intel_set_cdclk (struct drm_i915_private *dev_priv, -const struct intel_cdclk_state *cdclk_state); +void +intel_set_cdclk_pre_plane_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *cdclk_state, +enum pipe pipe); +void +intel_set_cdclk_post_plane_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *cdclk_state, +enum pipe pipe);void intel_dump_cdclk_state (const struct intel_cdclk_state *cdclk_state,const char *context);
Signature · 6 lines
2.13.2 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH v6 2/2] drm/i915: Skip modeset for cdclk changes if possible
Quoted 10 lines · Imre Deak
drivers/gpu/drm/i915/intel_cdclk.c +6
-0@@ -2137,6 +2194,44 @@ void intel_set_cdclk(struct drm_i915_private *dev_priv, } } +/** +* intel_set_cdclk_pre_plane_update - Push the CDCLK state to the hardware +* @dev_priv: i915 device +* @cdclk_state: new CDCLK state +* @pipe: pipe with which to synchronize the update +*
drivers/gpu/drm/i915/intel_cdclk.c void intel_set_cdclk(struct drm_i915_private *dev_priv, · line 2212
Quoted 10 lines
drivers/gpu/drm/i915/intel_cdclk.c +10
-0+* Program the hardware before updating the HW plane state based on the passed +* in CDCLK state, if necessary. +*/ +void +intel_set_cdclk_pre_plane_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *cdclk_state, +enum pipe pipe) +{ +if (pipe ==INVALID_PIPE || + dev_priv->cdclk.actual.cdclk >= cdclk_state->cdclk)
cdclk_state == &dev_priv->cdclk.actual
so these look a bit buggered.
Would be somewhat nice to use the private obj stuff for this but the locking now enforced by that make it difficult. Perhaps a swap(dev_priv->cdlk, state->cdclk) would be possible? A quick scan through the code didn't reveal any uses of state->cdclk outside the compute code paths, so looks safeish. Another option is just comparing against dev_priv->cdclk.hw since we still have that.
Quoted 146 lines
drivers/gpu/drm/i915/intel_cdclk.c +22
-0+intel_set_cdclk (dev_priv, cdclk_state, pipe); +} + +/** +* intel_set_cdclk_post_plane_update - Push the CDCLK state to the hardware +* @dev_priv: i915 device +* @cdclk_state: new CDCLK state +* @pipe: pipe with which to synchronize the update +* +* Program the hardware after updating the HW plane state based on the passed +* in CDCLK state, if necessary. +*/ +void +intel_set_cdclk_post_plane_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *cdclk_state, +enum pipe pipe) +{ +if (pipe !=INVALID_PIPE && + dev_priv->cdclk.actual.cdclk < cdclk_state->cdclk) +intel_set_cdclk (dev_priv, cdclk_state, pipe); +} +static int intel_pixel_rate_to_cdclk (struct drm_i915_private *dev_priv,int pixel_rate) {drivers/gpu/drm/i915/intel_display.c +36
-3@@ -12982,6 +12982,7 @@ static int intel_modeset_checks(struct drm_atomic_state *state) intel_state->active_crtcs = dev_priv->active_crtcs; intel_state->cdclk.logical = dev_priv->cdclk.logical; intel_state->cdclk.actual = dev_priv->cdclk.actual; + intel_state->cdclk.pipe =INVALID_PIPE ;for_each_oldnew_crtc_in_state (state, crtc, old_crtc_state, new_crtc_state, i) {if (new_crtc_state->active)@@ -13001,6 +13002,8 @@ static int intel_modeset_checks(struct drm_atomic_state *state)* adjusted_mode bits in the crtc directly. */ if (dev_priv->display.modeset_calc_cdclk) { +enum pipe pipe; + ret = dev_priv->display.modeset_calc_cdclk (state);if (ret <0 )return ret;@@ -13017,12 +13020,36 @@ static int intel_modeset_checks(struct drm_atomic_state *state)return ret; } +if (is_power_of_2 (intel_state->active_crtcs)) { +struct drm_crtc *crtc; +struct drm_crtc_state *crtc_state; + + pipe =ilog2 (intel_state->active_crtcs); + crtc = &intel_get_crtc_for_pipe (dev_priv, pipe)->base; + crtc_state =drm_atomic_get_new_crtc_state (state, crtc); +if (crtc_state &&needs_modeset (crtc_state)) + pipe =INVALID_PIPE ; + }else { + pipe =INVALID_PIPE ; + } +/* All pipes must be switched off while we change the cdclk. */ -if (intel_cdclk_needs_modeset (&dev_priv->cdclk.actual, - &intel_state->cdclk.actual)) { +if (pipe !=INVALID_PIPE && +intel_cdclk_needs_cd2x_update (dev_priv, + &dev_priv->cdclk.actual, + &intel_state->cdclk.actual)) { + ret =intel_lock_all_pipes (state); +if (ret <0 ) +return ret; + + intel_state->cdclk.pipe = pipe; + }else if (intel_cdclk_needs_modeset (&dev_priv->cdclk.actual, + &intel_state->cdclk.actual)) { ret =intel_modeset_all_pipes (state);if (ret <0 )return ret; + + intel_state->cdclk.pipe =INVALID_PIPE ; } DRM_DEBUG_KMS("New cdclk calculated to be logical %u kHz, actual %u kHz\n",@@ -13433,7 +13460,9 @@ static void intel_atomic_commit_tail(struct drm_atomic_state *state)if (intel_state->modeset) {drm_atomic_helper_update_legacy_modeset_state (state->dev, state); -intel_set_cdclk (dev_priv, &dev_priv->cdclk.actual); +intel_set_cdclk_pre_plane_update (dev_priv, + &dev_priv->cdclk.actual, + intel_state->cdclk.pipe);/* * SKL workaround: bspec recommends we disable the SAGV when we @@ -13462,6 +13491,10 @@ static void intel_atomic_commit_tail(struct drm_atomic_state *state)/* Now enable the clocks, plane, pipe, and connectors that we set up. */ dev_priv->display.update_crtcs (state); +intel_set_cdclk_post_plane_update (dev_priv, + &dev_priv->cdclk.actual, + intel_state->cdclk.pipe); +/* FIXME: We should call drm_atomic_helper_commit_hw_done() here * already, but still need the state for the delayed optimization. To * fix this: drivers/gpu/drm/i915/intel_drv.h +13
-2@@ -559,6 +559,8 @@ struct intel_atomic_state {int force_min_cdclk;bool force_min_cdclk_changed; +/* pipe to which cd2x update is synchronized */ +enum pipe pipe; } cdclk;bool dpll_set, modeset;@@ -1694,12 +1696,21 @@ void intel_init_cdclk_hooks(struct drm_i915_private *dev_priv);void intel_update_max_cdclk (struct drm_i915_private *dev_priv);void intel_update_cdclk (struct drm_i915_private *dev_priv);void intel_update_rawclk (struct drm_i915_private *dev_priv); +bool intel_cdclk_needs_cd2x_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *a, +const struct intel_cdclk_state *b);bool intel_cdclk_needs_modeset (const struct intel_cdclk_state *a,const struct intel_cdclk_state *b);bool intel_cdclk_changed (const struct intel_cdclk_state *a,const struct intel_cdclk_state *b); -void intel_set_cdclk (struct drm_i915_private *dev_priv, -const struct intel_cdclk_state *cdclk_state); +void +intel_set_cdclk_pre_plane_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *cdclk_state, +enum pipe pipe); +void +intel_set_cdclk_post_plane_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *cdclk_state, +enum pipe pipe);void intel_dump_cdclk_state (const struct intel_cdclk_state *cdclk_state,const char *context);Signature · 1 line
2.13.2
Signature · 6 lines
Ville Syrjälä Intel _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH v6 2/2] drm/i915: Skip modeset for cdclk changes if possible
Quoted 16 lines · Ville Syrjälä
Quoted 15 lines · Imre Deak
drivers/gpu/drm/i915/intel_cdclk.c +11
-0@@ -2137,6 +2194,44 @@ void intel_set_cdclk(struct drm_i915_private *dev_priv, } } +/** +* intel_set_cdclk_pre_plane_update - Push the CDCLK state to the hardware +* @dev_priv: i915 device +* @cdclk_state: new CDCLK state +* @pipe: pipe with which to synchronize the update +* +* Program the hardware before updating the HW plane state based on the passed +* in CDCLK state, if necessary. +*/ +void +intel_set_cdclk_pre_plane_update(struct drm_i915_private *dev_priv,
Quoted 8 lines
drivers/gpu/drm/i915/intel_cdclk.c void intel_set_cdclk(struct drm_i915_private *dev_priv, · line 2212
Quoted 5 lines
drivers/gpu/drm/i915/intel_cdclk.c +5
-0+const struct intel_cdclk_state *cdclk_state, + enum pipe pipe) +{ + if (pipe == INVALID_PIPE || + dev_priv->cdclk.actual.cdclk >= cdclk_state->cdclk)
cdclk_state==&dev_priv->cdclk.actual
so these look a bit buggered.
Yep, screwed this up..
Quoted 3 lines
Would be somewhat nice to use the private obj stuff for this but the locking now enforced by that make it difficult. Perhaps a
swap(dev_priv->cdlk, state->cdclk)would be possible?
I suppose you mean in intel_atomic_commit() already, where the swap is done already halfway, so in the end state->cdclk would become old_cdclk_state. That sounds fine to me.
Quoted 149 lines
A quick scan through the code didn't reveal any uses of
state->cdclkoutside the compute code paths, so looks safeish. Another option is just comparing againstdev_priv->cdclk.hwsince we still have that.Quoted 144 lines
drivers/gpu/drm/i915/intel_cdclk.c +22
-0+intel_set_cdclk (dev_priv, cdclk_state, pipe); +} + +/** +* intel_set_cdclk_post_plane_update - Push the CDCLK state to the hardware +* @dev_priv: i915 device +* @cdclk_state: new CDCLK state +* @pipe: pipe with which to synchronize the update +* +* Program the hardware after updating the HW plane state based on the passed +* in CDCLK state, if necessary. +*/ +void +intel_set_cdclk_post_plane_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *cdclk_state, +enum pipe pipe) +{ +if (pipe !=INVALID_PIPE && + dev_priv->cdclk.actual.cdclk < cdclk_state->cdclk) +intel_set_cdclk (dev_priv, cdclk_state, pipe); +} +static int intel_pixel_rate_to_cdclk (struct drm_i915_private *dev_priv,int pixel_rate) {drivers/gpu/drm/i915/intel_display.c +36
-3@@ -12982,6 +12982,7 @@ static int intel_modeset_checks(struct drm_atomic_state *state) intel_state->active_crtcs = dev_priv->active_crtcs; intel_state->cdclk.logical = dev_priv->cdclk.logical; intel_state->cdclk.actual = dev_priv->cdclk.actual; + intel_state->cdclk.pipe =INVALID_PIPE ;for_each_oldnew_crtc_in_state (state, crtc, old_crtc_state, new_crtc_state, i) {if (new_crtc_state->active)@@ -13001,6 +13002,8 @@ static int intel_modeset_checks(struct drm_atomic_state *state)* adjusted_mode bits in the crtc directly. */ if (dev_priv->display.modeset_calc_cdclk) { +enum pipe pipe; + ret = dev_priv->display.modeset_calc_cdclk (state);if (ret <0 )return ret;@@ -13017,12 +13020,36 @@ static int intel_modeset_checks(struct drm_atomic_state *state)return ret; } +if (is_power_of_2 (intel_state->active_crtcs)) { +struct drm_crtc *crtc; +struct drm_crtc_state *crtc_state; + + pipe =ilog2 (intel_state->active_crtcs); + crtc = &intel_get_crtc_for_pipe (dev_priv, pipe)->base; + crtc_state =drm_atomic_get_new_crtc_state (state, crtc); +if (crtc_state &&needs_modeset (crtc_state)) + pipe =INVALID_PIPE ; + }else { + pipe =INVALID_PIPE ; + } +/* All pipes must be switched off while we change the cdclk. */ -if (intel_cdclk_needs_modeset (&dev_priv->cdclk.actual, - &intel_state->cdclk.actual)) { +if (pipe !=INVALID_PIPE && +intel_cdclk_needs_cd2x_update (dev_priv, + &dev_priv->cdclk.actual, + &intel_state->cdclk.actual)) { + ret =intel_lock_all_pipes (state); +if (ret <0 ) +return ret; + + intel_state->cdclk.pipe = pipe; + }else if (intel_cdclk_needs_modeset (&dev_priv->cdclk.actual, + &intel_state->cdclk.actual)) { ret =intel_modeset_all_pipes (state);if (ret <0 )return ret; + + intel_state->cdclk.pipe =INVALID_PIPE ; } DRM_DEBUG_KMS("New cdclk calculated to be logical %u kHz, actual %u kHz\n",@@ -13433,7 +13460,9 @@ static void intel_atomic_commit_tail(struct drm_atomic_state *state)if (intel_state->modeset) {drm_atomic_helper_update_legacy_modeset_state (state->dev, state); -intel_set_cdclk (dev_priv, &dev_priv->cdclk.actual); +intel_set_cdclk_pre_plane_update (dev_priv, + &dev_priv->cdclk.actual, + intel_state->cdclk.pipe);/* * SKL workaround: bspec recommends we disable the SAGV when we @@ -13462,6 +13491,10 @@ static void intel_atomic_commit_tail(struct drm_atomic_state *state)/* Now enable the clocks, plane, pipe, and connectors that we set up. */ dev_priv->display.update_crtcs (state); +intel_set_cdclk_post_plane_update (dev_priv, + &dev_priv->cdclk.actual, + intel_state->cdclk.pipe); +/* FIXME: We should call drm_atomic_helper_commit_hw_done() here * already, but still need the state for the delayed optimization. To * fix this: drivers/gpu/drm/i915/intel_drv.h +13
-2@@ -559,6 +559,8 @@ struct intel_atomic_state {int force_min_cdclk;bool force_min_cdclk_changed; +/* pipe to which cd2x update is synchronized */ +enum pipe pipe; } cdclk;bool dpll_set, modeset;@@ -1694,12 +1696,21 @@ void intel_init_cdclk_hooks(struct drm_i915_private *dev_priv);void intel_update_max_cdclk (struct drm_i915_private *dev_priv);void intel_update_cdclk (struct drm_i915_private *dev_priv);void intel_update_rawclk (struct drm_i915_private *dev_priv); +bool intel_cdclk_needs_cd2x_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *a, +const struct intel_cdclk_state *b);bool intel_cdclk_needs_modeset (const struct intel_cdclk_state *a,const struct intel_cdclk_state *b);bool intel_cdclk_changed (const struct intel_cdclk_state *a,const struct intel_cdclk_state *b); -void intel_set_cdclk (struct drm_i915_private *dev_priv, -const struct intel_cdclk_state *cdclk_state); +void +intel_set_cdclk_pre_plane_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *cdclk_state, +enum pipe pipe); +void +intel_set_cdclk_post_plane_update (struct drm_i915_private *dev_priv, +const struct intel_cdclk_state *cdclk_state, +enum pipe pipe);void intel_dump_cdclk_state (const struct intel_cdclk_state *cdclk_state,const char *context);
Quoted 6 lines
Quoted 2 lines
Signature · 1 line
2.13.2Signature · 2 lines
Ville Syrjälä Intel
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.CHECKPATCH: warning for drm/i915: Ensure minimum CDCLK requirement for audio
In reply to Imre Deak== Series Details ==
== Series Details ==
Series: drm/i915: Ensure minimum CDCLK requirement for audio
URL : https://patchwork.freedesktop.org/series/58132/
State : warning
== Summary ==
$ dim checkpatch origin/drm-tip f5ea7a63eeb3 drm/i915: Force 2*96 MHz cdclk on glk/cnl when audio power is enabled -:60: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis #60: FILE: drivers/gpu/drm/i915/intel_audio.c:745: +static void glk_force_audio_cdclk(struct drm_i915_private *dev_priv, + bool enable)
total: 0 errors, 0 warnings, 1 checks, 212 lines checked e871b62f8db1 drm/i915: Skip modeset for cdclk changes if possible
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.SPARSE: warning for drm/i915: Ensure minimum CDCLK requirement for audio
In reply to Imre Deak== Series Details ==
== Series Details ==
Series: drm/i915: Ensure minimum CDCLK requirement for audio
URL : https://patchwork.freedesktop.org/series/58132/
State : warning
== Summary ==
$ dim sparse origin/drm-tip Sparse version: v0.5.2 Commit: drm/i915: Force 2*96 MHz cdclk on glk/cnl when audio power is enabled -O:drivers/gpu/drm/i915/intel_cdclk.c:2203:29: warning: expression using sizeof(void) +drivers/gpu/drm/i915/intel_cdclk.c:2192:29: warning: expression using sizeof(void) -O:drivers/gpu/drm/i915/intel_cdclk.c:2244:29: warning: expression using sizeof(void) -O:drivers/gpu/drm/i915/intel_cdclk.c:2244:29: warning: expression using sizeof(void) +drivers/gpu/drm/i915/intel_cdclk.c:2233:29: warning: expression using sizeof(void) +drivers/gpu/drm/i915/intel_cdclk.c:2233:29: warning: expression using sizeof(void) -drivers/gpu/drm/i915/selftests/../i915_drv.h:3558:16: warning: expression using sizeof(void) +drivers/gpu/drm/i915/selftests/../i915_drv.h:3561:16: warning: expression using sizeof(void)
Commit: drm/i915: Skip modeset for cdclk changes if possible+drivers/gpu/drm/i915/intel_cdclk.c:2137:6: warning: symbol 'intel_cdclk_can_skip_modeset' was not declared. Should it be static? -drivers/gpu/drm/i915/selftests/../i915_drv.h:3561:16: warning: expression using sizeof(void) +drivers/gpu/drm/i915/selftests/../i915_drv.h:3562:16: warning: expression using sizeof(void)
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.BAT: success for drm/i915: Ensure minimum CDCLK requirement for audio
In reply to Imre Deak== Series Details ==
== Series Details ==
Series: drm/i915: Ensure minimum CDCLK requirement for audio
URL : https://patchwork.freedesktop.org/series/58132/
State : success
== Summary ==
CI Bug Log - changes from CI_DRM_5767 -> Patchwork_12498
====================================================
Summary
-------
**SUCCESS**
No regressions found.
External URL: https://patchwork.freedesktop.org/api/1.0/series/58132/revisions/1/mbox/
Known issues
------------
Here are the changes found in Patchwork_12498 that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@kms_chamelium@common-hpd-after-suspend:
- fi-skl-6700k2: PASS -> INCOMPLETE [fdo#104108]
* igt@kms_pipe_crc_basic@nonblocking-crc-pipe-a-frame-sequence:
- fi-byt-clapper: PASS -> FAIL [fdo#103191] / [fdo#107362]
* igt@kms_pipe_crc_basic@nonblocking-crc-pipe-c:
- fi-kbl-7567u: PASS -> SKIP [fdo#109271] +27
* igt@prime_vgem@basic-fence-flip:
- fi-gdg-551: PASS -> FAIL [fdo#103182] +1
#### Possible fixes ####
* igt@i915_selftest@live_execlists:
- fi-apl-guc: INCOMPLETE [fdo#103927] / [fdo#109720] -> PASS
#### Warnings ####
* igt@i915_selftest@live_contexts:
- fi-icl-u3: INCOMPLETE [fdo#108569] -> DMESG-FAIL [fdo#108569]
* igt@kms_pipe_crc_basic@suspend-read-crc-pipe-a:
- fi-kbl-7567u: DMESG-FAIL [fdo#105079] -> SKIP [fdo#109271]
[fdo#103182]: https://bugs.freedesktop.org/show_bug.cgi?id=103182
[fdo#103191]: https://bugs.freedesktop.org/show_bug.cgi?id=103191
[fdo#103927]: https://bugs.freedesktop.org/show_bug.cgi?id=103927
[fdo#104108]: https://bugs.freedesktop.org/show_bug.cgi?id=104108
[fdo#105079]: https://bugs.freedesktop.org/show_bug.cgi?id=105079
[fdo#107362]: https://bugs.freedesktop.org/show_bug.cgi?id=107362
[fdo#108569]: https://bugs.freedesktop.org/show_bug.cgi?id=108569
[fdo#109271]: https://bugs.freedesktop.org/show_bug.cgi?id=109271
[fdo#109720]: https://bugs.freedesktop.org/show_bug.cgi?id=109720
Participating hosts (49 -> 40)
------------------------------
Missing (9): fi-kbl-soraka fi-ilk-m540 fi-bdw-5557u fi-hsw-4200u fi-byt-squawks fi-bsw-cyan fi-ctg-p8600 fi-icl-y fi-bdw-samus
Build changes
-------------
* Linux: CI_DRM_5767 -> Patchwork_12498
CI_DRM_5767: 289bd1852756ddd2779c32cd13ae10e7bf44faca @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4888: 71ad19eb8fe4f0eecae3bf063e107293b90b9abc @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_12498: e871b62f8db1ac9783a7fadbc50abe78d2f43730 @ git://anongit.freedesktop.org/gfx-ci/linux
== Linux commits ==
e871b62f8db1 drm/i915: Skip modeset for cdclk changes if possible f5ea7a63eeb3 drm/i915: Force 2*96 MHz cdclk on glk/cnl when audio power is enabled
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_12498/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.IGT: failure for drm/i915: Ensure minimum CDCLK requirement for audio
In reply to Imre Deak== Series Details ==
== Series Details ==
Series: drm/i915: Ensure minimum CDCLK requirement for audio
URL : https://patchwork.freedesktop.org/series/58132/
State : failure
== Summary ==
CI Bug Log - changes from CI_DRM_5767_full -> Patchwork_12498_full
====================================================
Summary
-------
**FAILURE**
Serious unknown changes coming with Patchwork_12498_full absolutely need to be verified manually.
If you think the reported changes have nothing to do with the changes introduced in Patchwork_12498_full, please notify your bug team to allow them to document this new failure mode, which will reduce false positives in CI.
Possible new issues
-------------------
Here are the unknown changes that may have been introduced in Patchwork_12498_full:
### IGT changes ###
#### Possible regressions ####
* igt@gem_tiled_swapping@non-threaded:
- shard-iclb: PASS -> FAIL
Known issues
------------
Here are the changes found in Patchwork_12498_full that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@gem_exec_parallel@bsd1-fds:
- shard-iclb: NOTRUN -> SKIP [fdo#109276] +1
* igt@gem_exec_schedule@fifo-bsd2:
- shard-snb: NOTRUN -> SKIP [fdo#109271] +69
* igt@gem_exec_schedule@wide-blt:
- shard-iclb: PASS -> FAIL [fdo#109633]
* igt@i915_pm_rpm@sysfs-read:
- shard-skl: PASS -> INCOMPLETE [fdo#107807]
* igt@kms_atomic_transition@3x-modeset-transitions:
- shard-skl: NOTRUN -> SKIP [fdo#109271] / [fdo#109278] +9
* igt@kms_atomic_transition@6x-modeset-transitions-fencing:
- shard-iclb: NOTRUN -> SKIP [fdo#109278] +1
* igt@kms_busy@extended-modeset-hang-newfb-render-b:
- shard-snb: NOTRUN -> DMESG-WARN [fdo#107956]
* igt@kms_busy@extended-modeset-hang-newfb-render-d:
- shard-apl: NOTRUN -> SKIP [fdo#109271] / [fdo#109278] +2
* igt@kms_busy@extended-modeset-hang-newfb-with-reset-render-b:
- shard-iclb: NOTRUN -> DMESG-WARN [fdo#107956]
* igt@kms_busy@extended-pageflip-hang-newfb-render-c:
- shard-apl: NOTRUN -> DMESG-WARN [fdo#107956]
* igt@kms_busy@extended-pageflip-modeset-hang-oldfb-render-c:
- shard-skl: NOTRUN -> DMESG-WARN [fdo#107956] +1
* igt@kms_ccs@pipe-b-crc-sprite-planes-basic:
- shard-iclb: PASS -> FAIL [fdo#107725]
* igt@kms_chamelium@vga-frame-dump:
- shard-iclb: NOTRUN -> SKIP [fdo#109284]
* igt@kms_content_protection@atomic-dpms:
- shard-apl: NOTRUN -> FAIL [fdo#108739]
* igt@kms_cursor_crc@cursor-size-change:
- shard-apl: PASS -> FAIL [fdo#103232]
* igt@kms_cursor_legacy@cursor-vs-flip-atomic:
- shard-iclb: PASS -> FAIL [fdo#103355]
* igt@kms_cursor_legacy@cursor-vs-flip-legacy:
- shard-hsw: PASS -> FAIL [fdo#103355]
* igt@kms_fbcon_fbt@fbc:
- shard-iclb: PASS -> DMESG-WARN [fdo#109593]
* igt@kms_fbcon_fbt@psr:
- shard-skl: NOTRUN -> FAIL [fdo#103833]
* igt@kms_flip@2x-flip-vs-dpms:
- shard-iclb: NOTRUN -> SKIP [fdo#109274] +1
* igt@kms_flip@flip-vs-expired-vblank:
- shard-glk: PASS -> FAIL [fdo#102887] / [fdo#105363]
* igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-fullscreen:
- shard-skl: NOTRUN -> FAIL [fdo#103167]
* igt@kms_frontbuffer_tracking@fbc-2p-primscrn-cur-indfb-draw-mmap-cpu:
- shard-glk: PASS -> FAIL [fdo#103167] +6
* igt@kms_frontbuffer_tracking@fbcpsr-2p-primscrn-cur-indfb-draw-mmap-wc:
- shard-iclb: NOTRUN -> SKIP [fdo#109280] +3
* igt@kms_frontbuffer_tracking@fbcpsr-rgb565-draw-render:
- shard-iclb: PASS -> FAIL [fdo#103167] +6
* igt@kms_frontbuffer_tracking@psr-1p-primscrn-spr-indfb-fullscreen:
- shard-iclb: PASS -> FAIL [fdo#109247] +17
* igt@kms_frontbuffer_tracking@psr-2p-scndscrn-pri-indfb-draw-pwrite:
- shard-hsw: NOTRUN -> SKIP [fdo#109271] +9
* igt@kms_pipe_crc_basic@suspend-read-crc-pipe-c:
- shard-kbl: PASS -> INCOMPLETE [fdo#103665]
* igt@kms_plane_scaling@pipe-b-scaler-with-clipping-clamping:
- shard-apl: PASS -> INCOMPLETE [fdo#103927]
* igt@kms_psr@basic:
- shard-apl: NOTRUN -> SKIP [fdo#109271] +56
* igt@kms_psr@psr2_sprite_plane_move:
- shard-iclb: PASS -> SKIP [fdo#109441] +2
* igt@kms_psr@psr2_suspend:
- shard-iclb: NOTRUN -> SKIP [fdo#109441]
* igt@kms_psr@sprite_mmap_gtt:
- shard-iclb: PASS -> FAIL [fdo#107383] +3
* igt@kms_vblank@pipe-c-wait-busy:
- shard-snb: NOTRUN -> SKIP [fdo#109271] / [fdo#109278] +9
* igt@kms_vrr@flip-basic:
- shard-iclb: NOTRUN -> SKIP [fdo#109502]
* igt@perf@oa-exponents:
- shard-glk: PASS -> FAIL [fdo#105483]
* igt@perf_pmu@semaphore-wait-vcs1:
- shard-skl: NOTRUN -> SKIP [fdo#109271] +97
* igt@prime_nv_api@i915_nv_double_export:
- shard-iclb: NOTRUN -> SKIP [fdo#109291]
* igt@runner@aborted:
- shard-iclb: NOTRUN -> FAIL [fdo#109593]
* igt@sw_sync@sync_busy_fork_unixsocket:
- shard-iclb: NOTRUN -> FAIL [fdo#110150 ]
#### Possible fixes ####
* igt@gem_create@create-clear:
- shard-hsw: INCOMPLETE [fdo#103540] -> PASS
* igt@gem_pwrite@big-cpu-fbr:
- shard-iclb: TIMEOUT [fdo#109673] -> PASS +1
* igt@kms_ccs@pipe-a-crc-sprite-planes-basic:
- shard-glk: FAIL [fdo#108145] -> PASS
* igt@kms_color@pipe-a-degamma:
- shard-apl: FAIL [fdo#104782] / [fdo#108145] -> PASS
* igt@kms_cursor_crc@cursor-128x128-onscreen:
- shard-apl: FAIL [fdo#103232] -> PASS +1
* igt@kms_cursor_legacy@cursor-vs-flip-varying-size:
- shard-iclb: FAIL [fdo#103355] -> PASS
* igt@kms_flip@2x-flip-vs-expired-vblank:
- shard-glk: FAIL [fdo#105363] -> PASS
* igt@kms_flip@flip-vs-expired-vblank:
- shard-apl: FAIL [fdo#102887] / [fdo#105363] -> PASS
* igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-draw-mmap-cpu:
- shard-glk: FAIL [fdo#103167] -> PASS
* igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-draw-pwrite:
- shard-apl: FAIL [fdo#103167] -> PASS +1
* igt@kms_frontbuffer_tracking@fbcpsr-1p-offscren-pri-indfb-draw-blt:
- shard-iclb: FAIL [fdo#109247] -> PASS +12
* igt@kms_frontbuffer_tracking@fbcpsr-1p-primscrn-cur-indfb-draw-render:
- shard-iclb: FAIL [fdo#103167] -> PASS +8
* igt@kms_frontbuffer_tracking@fbcpsr-rgb101010-draw-blt:
- shard-iclb: FAIL [fdo#105682] / [fdo#109247] -> PASS +1
* {igt@kms_plane@pixel-format-pipe-b-planes}:
- shard-apl: FAIL [fdo#110033] -> PASS
* igt@kms_plane@plane-panning-bottom-right-suspend-pipe-a-planes:
- shard-snb: INCOMPLETE [fdo#105411] -> PASS
* {igt@kms_plane@plane-position-covered-pipe-a-planes}:
- shard-iclb: FAIL [fdo#110038] -> PASS
* igt@kms_plane_alpha_blend@pipe-b-constant-alpha-min:
- shard-skl: FAIL [fdo#108145] -> PASS
* {igt@kms_plane_multiple@atomic-pipe-b-tiling-none}:
- shard-iclb: FAIL [fdo#110037] -> PASS
* {igt@kms_plane_multiple@atomic-pipe-c-tiling-none}:
- shard-glk: FAIL [fdo#110037] -> PASS +1
* igt@kms_psr2_su@frontbuffer:
- shard-iclb: SKIP [fdo#109642] -> PASS
* igt@kms_psr@cursor_blt:
- shard-iclb: FAIL [fdo#107383] -> PASS +2
* igt@kms_psr@psr2_cursor_plane_move:
- shard-iclb: SKIP [fdo#109441] -> PASS
* igt@kms_rotation_crc@multiplane-rotation:
- shard-iclb: DMESG-WARN [fdo#106885] -> PASS
* igt@kms_setmode@basic:
- shard-apl: FAIL [fdo#99912] -> PASS
#### Warnings ####
* igt@i915_selftest@live_contexts:
- shard-iclb: DMESG-FAIL [fdo#108569] -> INCOMPLETE [fdo#108569]
* igt@kms_plane_scaling@pipe-b-scaler-with-rotation:
- shard-glk: SKIP [fdo#109271] / [fdo#109278] -> FAIL [fdo#110098]
### Piglit changes ###
#### Issues hit ####
* spec@arb_fragment_shader_interlock@arb_fragment_shader_interlock-image-load-store:
- pig-hsw-4770r: NOTRUN -> FAIL [fdo#109980]
{name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).
[fdo#102887]: https://bugs.freedesktop.org/show_bug.cgi?id=102887
[fdo#103167]: https://bugs.freedesktop.org/show_bug.cgi?id=103167
[fdo#103232]: https://bugs.freedesktop.org/show_bug.cgi?id=103232
[fdo#103355]: https://bugs.freedesktop.org/show_bug.cgi?id=103355
[fdo#103540]: https://bugs.freedesktop.org/show_bug.cgi?id=103540
[fdo#103665]: https://bugs.freedesktop.org/show_bug.cgi?id=103665
[fdo#103833]: https://bugs.freedesktop.org/show_bug.cgi?id=103833
[fdo#103927]: https://bugs.freedesktop.org/show_bug.cgi?id=103927
[fdo#104782]: https://bugs.freedesktop.org/show_bug.cgi?id=104782
[fdo#105363]: https://bugs.freedesktop.org/show_bug.cgi?id=105363
[fdo#105411]: https://bugs.freedesktop.org/show_bug.cgi?id=105411
[fdo#105483]: https://bugs.freedesktop.org/show_bug.cgi?id=105483
[fdo#105682]: https://bugs.freedesktop.org/show_bug.cgi?id=105682
[fdo#106885]: https://bugs.freedesktop.org/show_bug.cgi?id=106885
[fdo#107383]: https://bugs.freedesktop.org/show_bug.cgi?id=107383
[fdo#107725]: https://bugs.freedesktop.org/show_bug.cgi?id=107725
[fdo#107807]: https://bugs.freedesktop.org/show_bug.cgi?id=107807
[fdo#107956]: https://bugs.freedesktop.org/show_bug.cgi?id=107956
[fdo#108145]: https://bugs.freedesktop.org/show_bug.cgi?id=108145
[fdo#108569]: https://bugs.freedesktop.org/show_bug.cgi?id=108569
[fdo#108739]: https://bugs.freedesktop.org/show_bug.cgi?id=108739
[fdo#109247]: https://bugs.freedesktop.org/show_bug.cgi?id=109247
[fdo#109271]: https://bugs.freedesktop.org/show_bug.cgi?id=109271
[fdo#109274]: https://bugs.freedesktop.org/show_bug.cgi?id=109274
[fdo#109276]: https://bugs.freedesktop.org/show_bug.cgi?id=109276
[fdo#109278]: https://bugs.freedesktop.org/show_bug.cgi?id=109278
[fdo#109280]: https://bugs.freedesktop.org/show_bug.cgi?id=109280
[fdo#109284]: https://bugs.freedesktop.org/show_bug.cgi?id=109284
[fdo#109291]: https://bugs.freedesktop.org/show_bug.cgi?id=109291
[fdo#109441]: https://bugs.freedesktop.org/show_bug.cgi?id=109441
[fdo#109502]: https://bugs.freedesktop.org/show_bug.cgi?id=109502
[fdo#109593]: https://bugs.freedesktop.org/show_bug.cgi?id=109593
[fdo#109633]: https://bugs.freedesktop.org/show_bug.cgi?id=109633
[fdo#109642]: https://bugs.freedesktop.org/show_bug.cgi?id=109642
[fdo#109673]: https://bugs.freedesktop.org/show_bug.cgi?id=109673
[fdo#109980]: https://bugs.freedesktop.org/show_bug.cgi?id=109980
[fdo#110033]: https://bugs.freedesktop.org/show_bug.cgi?id=110033
[fdo#110037]: https://bugs.freedesktop.org/show_bug.cgi?id=110037
[fdo#110038]: https://bugs.freedesktop.org/show_bug.cgi?id=110038
[fdo#110098]: https://bugs.freedesktop.org/show_bug.cgi?id=110098
[fdo#110150 ]: https://bugs.freedesktop.org/show_bug.cgi?id=110150
[fdo#99912]: https://bugs.freedesktop.org/show_bug.cgi?id=99912
Participating hosts (9 -> 10)
------------------------------
Additional (1): pig-hsw-4770r
Build changes
-------------
* Linux: CI_DRM_5767 -> Patchwork_12498
CI_DRM_5767: 289bd1852756ddd2779c32cd13ae10e7bf44faca @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4888: 71ad19eb8fe4f0eecae3bf063e107293b90b9abc @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_12498: e871b62f8db1ac9783a7fadbc50abe78d2f43730 @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_12498/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx