keytable: minor rewording from TABLE to KEYMAP
PATCH 1/1 keytable: minor rewording from TABLE to KEYMAP
Signed-off-by Sean Young <[email protected]>
--- utils/keytable/ir-keytable.1.in | 15 +++++++++------ utils/keytable/keytable.c | 6 +++--- 2 files changed, 12 insertions(+), 9 deletions(-)
utils/keytable/ir-keytable.1.in +9 -6
@@ -57,8 +57,8 @@ test if the rc device is generating events \fB\-v\fR, \fB\-\-verbose\fR Enables debug messages. .TP -\fB\-w\fR, \fB\-\-write\fR=\fITABLE\fR -Reads the protocols and scancode to keycode mapping from the \fITABLE\fR file, +\fB\-w\fR, \fB\-\-write\fR=\fIKEYMAP\fR +Reads the protocols and scancode to keycode mapping from the \fIKEYMAP\fR file, and enables those on the rc device. .TP \fB\-?\fR, \fB\-\-help\fR
@@ -77,8 +77,9 @@ for any corresponding short options. Options can be combined together. the /dev/input/event* device to control .IP \fISYSDEV\fR the rc class as found at /sys/class/rc -.IP \fITABLE\fR -a toml file with a list of protocols and scancode to keycode mappings. +.IP \fIKEYMAP\fR +a toml keymap file with a list of protocols and scancodes to keycode mappings. +The format is described in rc_keymap(5). .IP \fISCANKEY\fR a set of scancode1=keycode1,scancode2=keycode2.. value pairs .IP \fIPROTOCOL\fR
@@ -112,7 +113,8 @@ To append more codes to the existing table: .br \fBir\-keytable \-w /etc/rc_keymaps/nec_terratec_cinergy_xs.toml\fR .PP -To read the current keytable, on the second remote controller: +To read the current scancode to keycode mapping on the second remote controller: +.br \fBir\-keytable \-s rc1 \-r\fR .PP To enable NEC protocol and load a BPF protocol, with a parameter for the BPF protocol:
@@ -135,5 +137,6 @@ License GPLv2: GNU GPL version 2 <http://gnu.org/licenses/gpl.html>. This is free software: you are free to change and redistribute it. There is NO WARRANTY, to the extent permitted by law. .SH SEE ALSO -rc_keymap(5). +The keymap format is described in rc_keymap(5). + To transmit IR or receive raw IR, see ir\-ctl(1).
utils/keytable/keytable.c +3 -3
@@ -232,10 +232,10 @@ static const char doc[] = N_("\nOn the options below, the arguments are:\n" " DEV - the /dev/input/event* device to control\n" " SYSDEV - the ir class as found at /sys/class/rc\n" -" TABLE - a file with a set of scancode=keycode value pairs\n" +" KEYMAP - a keymap file with protocols and scancode to keycode mappings\n" " SCANKEY - a set of scancode1=keycode1,scancode2=keycode2.. value pairs\n" " PROTOCOL - protocol name (nec, rc-5, rc-6, jvc, sony, sanyo, rc-5-sz, lirc,\n" -" sharp, mce_kbd, xmp, imon, rc_mm, other, all) to be enabled,\n" +" sharp, mce_kbd, xmp, imon, rc-mm, other, all) to be enabled,\n" " or a bpf protocol name or file\n" " DELAY - Delay before repeating a keystroke\n" " PERIOD - Period to repeat a keystroke\n"
@@ -251,7 +251,7 @@ static const struct argp_option options[] = { {"test", 't', 0, 0, N_("test if IR is generating events"), 0}, {"device", 'd', N_("DEV"), 0, N_("ir device to control"), 0}, {"read", 'r', 0, 0, N_("reads the current scancode/keycode table"), 0}, - {"write", 'w', N_("TABLE"), 0, N_("write (adds) the scancodes to the device scancode/keycode table from an specified file"), 0}, + {"write", 'w', N_("KEYMAP"), 0, N_("write (adds) the keymap from the specified file"), 0}, {"set-key", 'k', N_("SCANKEY"), 0, N_("Change scan/key pairs"), 0}, {"protocol", 'p', N_("PROTOCOL"), 0, N_("Protocol to enable (the other ones will be disabled). To enable more than one, use the option more than one time"), 0}, {"parameter", 'e', N_("PARAMETER"), 0, N_("Set a parameter for the protocol decoder")},
Signature · 1 line
2.20.1