Skip to contentSkip to conversation

board/qemu/riscv32-virt: Convert defconfig into a fragment

PATCH New Alistair Francis 3 participants 11 messages Mar 20, 2019 – Mar 26, 2019 RISC-V

lore
Share & tools
lore
#0 lore raw

PATCH v6 1/5 board/qemu/riscv32-virt: Convert defconfig into a fragment

Convert the config to the arch defconfig plus a fragment. When this fragment is applied we will generate the same config as we previously did.

---
 board/qemu/riscv32-virt/linux.config          |  23 ----
 board/qemu/riscv32-virt/linux.config.fragment | 104 ++++++++++++++++++
 configs/qemu_riscv32_virt_defconfig           |   4 +-
 3 files changed, 106 insertions(+), 25 deletions(-)
 delete mode 100644 board/qemu/riscv32-virt/linux.config
 create mode 100644 board/qemu/riscv32-virt/linux.config.fragment
board/qemu/riscv32-virt/linux.config deleted +0 -23
deleted file mode 100644
index c25583f768..0000000000
@@ -1,23 +0,0 @@
-CONFIG_ARCH_RV32I=y
-CONFIG_SMP=y
-CONFIG_NR_CPUS=8
-CONFIG_PCI=y
-CONFIG_SYSVIPC=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-# CONFIG_WIRELESS is not set
-CONFIG_VIRTIO_BLK=y
-CONFIG_NETDEVICES=y
-CONFIG_VIRTIO_NET=y
-# CONFIG_ETHERNET is not set
-# CONFIG_WLAN is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_VIRT_DRIVERS=y
-CONFIG_VIRTIO_MMIO=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT4_FS=y
-CONFIG_TMPFS=y
board/qemu/riscv32-virt/linux.config.fragment new file +104 -0

104 lines not on this page · raw message

configs/qemu_riscv32_virt_defconfig +2 -2
index 6f9a61b11c..fab152e50a 100644
@@ -18,8 +18,8 @@ BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/riscv/riscv-linux.git"
 BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="8fe28cb58bcb235034b64cbbb7550a8a43fd88be"
-BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/riscv32-virt/linux.config"
+BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y
+BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="board/qemu/riscv32-virt/linux.config.fragment"
 
 # Bootloader
 BR2_TARGET_RISCV_PK=y
Signature · 1 line
2.21.0
#1 lore raw

PATCH v6 2/5 board/qemu/riscv32-virt: Simplify the linux config

Reduce the config fragment to the bare minimum to enable 32-bit support. This means we are as close as possible to the arch defconfig.

---
 board/qemu/riscv32-virt/linux.config.fragment | 100 +-----------------
 1 file changed, 4 insertions(+), 96 deletions(-)
board/qemu/riscv32-virt/linux.config.fragment +4 -96
index 2ecc83c8e1..bca9aa61c7 100644
@@ -1,104 +1,12 @@
+CONFIG_32BIT=y
 CONFIG_ARCH_RV32I=y
 # CONFIG_ARCH_RV64I is not set
-# CONFIG_ATA is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-# CONFIG_BLK_DEV_INITRD is not set
-# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BPF_SYSCALL is not set
-# CONFIG_CGROUPS is not set
-# CONFIG_CHECKPOINT_RESTORE is not set
-# CONFIG_CMODEL_MEDANY is not set
-CONFIG_CMODEL_MEDLOW=y
-CONFIG_CRYPTO_AEAD=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_DEV_VIRTIO=y
-CONFIG_CRYPTO_DRBG=y
-CONFIG_CRYPTO_DRBG_MENU=y
-CONFIG_CRYPTO_ECHAINIV=y
-CONFIG_CRYPTO_ENGINE=y
-CONFIG_CRYPTO_HMAC=y
-CONFIG_CRYPTO_JITTERENTROPY=y
-CONFIG_CRYPTO_MANAGER=y
-CONFIG_CRYPTO_NULL=y
-CONFIG_CRYPTO_RNG=y
-CONFIG_CRYPTO_RNG_DEFAULT=y
-CONFIG_CRYPTO_SHA256=y
-# CONFIG_CRYPTO_USER_API_HASH is not set
-# CONFIG_DEBUG_KERNEL is not set
-CONFIG_DEBUG_MEMORY_INIT=y
-# CONFIG_DRM is not set
-# CONFIG_ETHERNET is not set
-# CONFIG_EXPERT is not set
-CONFIG_EXT2_FS=y
-# CONFIG_EXT4_FS_POSIX_ACL is not set
-# CONFIG_FB is not set
-CONFIG_FRAME_WARN=1024
-# CONFIG_FTRACE is not set
-CONFIG_HID_A4TECH=y
-CONFIG_HID_APPLE=y
-CONFIG_HID_BELKIN=y
-CONFIG_HID_CHERRY=y
-CONFIG_HID_CHICONY=y
-CONFIG_HID_CYPRESS=y
-CONFIG_HID_EZKEY=y
-CONFIG_HID_ITE=y
-CONFIG_HID_KENSINGTON=y
-CONFIG_HID_LOGITECH=y
-CONFIG_HID_MICROSOFT=y
-CONFIG_HID_MONTEREY=y
-CONFIG_HID_REDRAGON=y
-# CONFIG_HVC_RISCV_SBI is not set
-CONFIG_HW_RANDOM=y
-# CONFIG_I2C is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_INPUT_FF_MEMLESS=y
-# CONFIG_INPUT_MOUSEDEV is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_PNP is not set
-# CONFIG_KEYS is not set
 CONFIG_MAXPHYSMEM_2GB=y
-# CONFIG_MDIO_DEVICE is not set
-# CONFIG_MODULES is not set
-# CONFIG_MSDOS_FS is not set
-# CONFIG_NETLINK_DIAG is not set
-# CONFIG_NFS_FS is not set
-# CONFIG_NLS is not set
-CONFIG_PAGE_OFFSET=0xC0000000
-# CONFIG_PCIE_XILINX is not set
-CONFIG_PGTABLE_LEVELS=2
-# CONFIG_PHYLIB is not set
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_PRINTK_TIME is not set
-# CONFIG_PROC_CHILDREN is not set
-# CONFIG_RAS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SIFIVE_PLIC is not set
-# CONFIG_SYNC_FILE is not set
-# CONFIG_TMPFS_POSIX_ACL is not set
-# CONFIG_TMPFS_XATTR is not set
-# CONFIG_USB is not set
-# CONFIG_USER_NS is not set
-# CONFIG_VFAT_FS is not set
-CONFIG_VIRT_DRIVERS=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-# CONFIG_WIRELESS is not set
-# CONFIG_WLAN is not set
-# CONFIG_XZ_DEC is not set
-CONFIG_32BIT=y
-# CONFIG_EXT2_FS_XATTR is not set
+CONFIG_LBDAF=y
+# CONFIG_SCSI_NSP32 is not set
 CONFIG_GENERIC_ATOMIC64=y
 CONFIG_GENERIC_LIB_ASHLDI3=y
 CONFIG_GENERIC_LIB_ASHRDI3=y
 CONFIG_GENERIC_LIB_LSHRDI3=y
 CONFIG_GENERIC_LIB_UCMPDI2=y
-# CONFIG_HID_LOGITECH_HIDPP is not set
-CONFIG_LBDAF=y
-# CONFIG_LOGIG940_FF is not set
-# CONFIG_LOGIRUMBLEPAD2_FF is not set
-# CONFIG_LOGITECH_FF is not set
-# CONFIG_LOGIWHEELS_FF is not set
-
+CONFIG_GENERIC_LIB_UMODDI3=y
Signature · 1 line
2.21.0
#2 lore raw

PATCH v6 2/5 board/qemu/riscv32-virt: Simplify the linux config

Quoted 8 lines · On Wed, 20 Mar 2019 23:05:21 +0000 Alistair Francis <[email protected]>…

Reduce the config fragment to the bare minimum to enable 32-bit support. This means we are as close as possible to the arch defconfig.

---
 board/qemu/riscv32-virt/linux.config.fragment | 100 +-----------------
 1 file changed, 4 insertions(+), 96 deletions(-)

Applied to master, thanks.

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
#3 lore raw

PATCH v6 3/5 boot/opensbi: new package

In reply to Alistair Francis

OpenSBI is a much improved alternative to BBL (riscv-pk). Add OpenSBI support to buildroot.

---
 DEVELOPERS              |  1 +
 boot/Config.in          |  1 +
 boot/opensbi/Config.in  | 25 +++++++++++++++++++++++++
 boot/opensbi/opensbi.mk | 37 +++++++++++++++++++++++++++++++++++++
 4 files changed, 64 insertions(+)
 create mode 100644 boot/opensbi/Config.in
 create mode 100644 boot/opensbi/opensbi.mk
DEVELOPERS +1 -0
index 3e0ac08e11..91eda42949 100644
@@ -122,6 +122,7 @@ F:	package/kvazaar/
 F:	package/v4l2loopback/
 
 N:	Alistair Francis <[email protected]>
+F:	boot/opensbi/
 F:	package/xen/
 
 N:	Alvaro G. M <[email protected]>
boot/Config.in +1 -0
index 74481e7545..97bd3de6e9 100644
@@ -14,6 +14,7 @@ source "boot/lpc32xxcdl/Config.in"
 source "boot/mv-ddr-marvell/Config.in"
 source "boot/mxs-bootlets/Config.in"
 source "boot/optee-os/Config.in"
+source "boot/opensbi/Config.in"
 source "boot/riscv-pk/Config.in"
 source "boot/s500-bootloader/Config.in"
 source "boot/shim/Config.in"
boot/opensbi/Config.in new file +25 -0
new file mode 100644
index 0000000000..5f3cc13312
@@ -0,0 +1,25 @@
+config BR2_TARGET_OPENSBI
+	bool "opensbi"
+	depends on BR2_riscv
+	help
+	  OpenSBI aims to provide an open-source and extensible
+	  implementation of the RISC-V SBI specification for a platform
+	  specific firmware (M-mode) and a general purpose OS,
+	  hypervisor or bootloader (S-mode or HS-mode). OpenSBI
+	  implementation can be easily extended by RISC-V platform or
+	  System-on-Chip vendors to fit a particular hadware
+	  configuration.
+
+	  https://github.com/riscv/opensbi.git
+
+if BR2_TARGET_OPENSBI
+config BR2_TARGET_OPENSBI_PLAT
+	string "OpenSBI Platform"
+	default ""
+	help
+	  Specifies the OpenSBI platform to build. If no platform is
+	  specified only the OpenSBI platform independent static
+	  library libsbi.a is built. If a platform is specified then
+	  the platform specific static library libplatsbi.a and firmware
+	  examples are built.
+endif
boot/opensbi/opensbi.mk new file +37 -0
new file mode 100644
index 0000000000..ba4ff06c28
@@ -0,0 +1,37 @@
+################################################################################
+#
+# opensbi
+#
+################################################################################
+
+OPENSBI_VERSION = v0.3
+OPENSBI_SITE = $(call github,riscv,opensbi,$(OPENSBI_VERSION))
+OPENSBI_LICENSE = BSD-2-Clause
+OPENSBI_LICENSE_FILES = COPYING.BSD
+OPENSBI_INSTALL_IMAGES = YES
+
+OPENSBI_MAKE_ENV = \
+	CROSS_COMPILE=$(TARGET_CROSS)
+
+OPENSBI_PLAT = $(call qstrip,$(BR2_TARGET_OPENSBI_PLAT))
+ifneq ($(OPENSBI_PLAT),)
+OPENSBI_MAKE_ENV += PLATFORM=$(OPENSBI_PLAT)
+endif
+
+define OPENSBI_BUILD_CMDS
+	$(TARGET_MAKE_ENV) $(OPENSBI_MAKE_ENV) $(MAKE) -C $(@D)
+endef
+
+ifneq ($(OPENSBI_PLAT),)
+define OPENSBI_INSTALL_IMAGES_CMDS
+	$(INSTALL) -m 0644 -D $(@D)/build/platform/$(OPENSBI_PLAT)/firmware/fw_jump.bin $(BINARIES_DIR)/fw_jump.bin
+	$(INSTALL) -m 0644 -D $(@D)/build/platform/$(OPENSBI_PLAT)/firmware/fw_jump.elf $(BINARIES_DIR)/fw_jump.elf
+endef
+endif
+
+# Install libsbi.a in the host lib dir so it can be linked in the future.
+define OPENSBI_INSTALL_STAGING_CMDS
+	$(INSTALL) -m 0644 -D $(@D)/build/lib/libsbi.a $(STAGING_DIR)/usr/share/opensbi/libsbi.a
+endef
+
+$(eval $(generic-package))
Signature · 1 line
2.21.0
#4 lore raw

PATCH v6 3/5 boot/opensbi: new package

Hello,

Quoted 4 lines · On Wed, 20 Mar 2019 23:05:21 +0000 Alistair Francis <[email protected]>…

OpenSBI is a much improved alternative to BBL (riscv-pk). Add OpenSBI support to buildroot.

I have applied, but after doing a few changes for things that were not completely correct. See below.

boot/opensbi/opensbi.mk line 11

Quoted 5 lines
boot/opensbi/opensbi.mk new file +5 -0
+OPENSBI_VERSION = v0.3
+OPENSBI_SITE = $(call github,riscv,opensbi,$(OPENSBI_VERSION))
+OPENSBI_LICENSE = BSD-2-Clause
+OPENSBI_LICENSE_FILES = COPYING.BSD
+OPENSBI_INSTALL_IMAGES = YES

This is only really needed when OPENSBI_PLAT != "", so I've moved this statement inside the appropriate condition.

I've added OPENSBI_INSTALL_TARGET = NO, because we're not installing anything to target.

But more importantly, I've added OPENSBI_INSTALL_STAGING = YES, without which your OPENSBI_INSTALL_STAGING_CMDS is never called. I'm not sure how you tested this, but it clearly couldn't work as is.

Quoted 1 line

+# Install libsbi.a in the host lib dir so it can be linked in the future.

The library is not installed in host dir. So I've changed this to rather explain why we install in usr/share/opensbi and not in usr/lib.

Applied with those issues fixed. Thanks!

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
#5 lore raw

PATCH v6 3/5 boot/opensbi: new package

Quoted 6 lines · Thomas Petazzoni

Hello,

On Wed, 20 Mar 2019 23:05:21 +0000 Alistair Francis <[email protected]> wrote:

Quoted 7 lines
Quoted 4 lines

OpenSBI is a much improved alternative to BBL (riscv-pk). Add OpenSBI support to buildroot.

I have applied, but after doing a few changes for things that were not completely correct. See below.

Thanks for applying this and the rest of the series.

Quoted 10 lines

boot/opensbi/opensbi.mk line 11

Quoted 6 lines
boot/opensbi/opensbi.mk new file +5 -0
+OPENSBI_VERSION = v0.3
+OPENSBI_SITE = $(call github,riscv,opensbi,$(OPENSBI_VERSION))
+OPENSBI_LICENSE = BSD-2-Clause
+OPENSBI_LICENSE_FILES = COPYING.BSD
+OPENSBI_INSTALL_IMAGES = YES

This is only really needed when OPENSBI_PLAT != "", so I've moved this statement inside the appropriate condition.

Quoted 2 lines

I've added OPENSBI_INSTALL_TARGET = NO, because we're not installing anything to target.

Thanks

Quoted 4 lines

But more importantly, I've added OPENSBI_INSTALL_STAGING = YES, without which your OPENSBI_INSTALL_STAGING_CMDS is never called. I'm not sure how you tested this, but it clearly couldn't work as is.

Ah, I tested it in the previous version when I was using the Image install, but must have missed checking it was installed in the latest version. Sorry about that.

Quoted 5 lines
Quoted 2 lines

+# Install libsbi.a in the host lib dir so it can be linked in the future.

The library is not installed in host dir. So I've changed this to rather explain why we install in usr/share/opensbi and not in usr/lib.

Thanks for this.

Alistair

Quoted 8 lines

Applied with those issues fixed. Thanks!

Thomas
--
Thomas Petazzoni, CTO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

#6 lore raw

PATCH v6 4/5 configs: qemu_riscv*_virt: Use OpenSBI by default

In reply to Alistair Francis

Use OpenSBI by default instead of riscv-pk (BBL).

---
 board/qemu/riscv32-virt/readme.txt  | 6 +++---
 board/qemu/riscv64-virt/readme.txt  | 6 +++---
 configs/qemu_riscv32_virt_defconfig | 5 ++++-
 configs/qemu_riscv64_virt_defconfig | 5 ++++-
 4 files changed, 14 insertions(+), 8 deletions(-)
board/qemu/riscv32-virt/readme.txt +3 -3
index 2da99580e5..b984e47105 100644
@@ -1,7 +1,7 @@
-Run the emulation with:
+Run Linux in emulation with:
 
-  qemu-system-riscv32 -M virt -kernel output/images/bbl -append "root=/dev/vda ro console=ttyS0" -drive file=output/images/rootfs.ext2,format=raw,id=hd0 -device virtio-blk-device,drive=hd0 -netdev user,id=net0 -device virtio-net-device,netdev=net0 -nographic
+  qemu-system-riscv32 -M virt -kernel output/images/fw_jump.elf -device loader,file=output/images/Image,addr=0x80400000 -append "root=/dev/vda ro" -drive file=output/images/rootfs.ext2,format=raw,id=hd0 -device virtio-blk-device,drive=hd0 -netdev user,id=net0 -device virtio-net-device,netdev=net0 -nographic
 
 The login prompt will appear in the terminal that started Qemu.
 
-Tested with QEMU 2.12.1
+Tested with QEMU 3.1
board/qemu/riscv64-virt/readme.txt +3 -3
index 9f6e35c867..84c7ab3221 100644
@@ -1,7 +1,7 @@
-Run the emulation with:
+Run Linux in emulation with:
 
-  qemu-system-riscv64 -M virt -kernel output/images/bbl -append "root=/dev/vda ro console=ttyS0" -drive file=output/images/rootfs.ext2,format=raw,id=hd0 -device virtio-blk-device,drive=hd0 -netdev user,id=net0 -device virtio-net-device,netdev=net0 -nographic
+  qemu-system-riscv64 -M virt -kernel output/images/fw_jump.elf -device loader,file=output/images/Image,addr=0x80200000 -append "root=/dev/vda ro" -drive file=output/images/rootfs.ext2,format=raw,id=hd0 -device virtio-blk-device,drive=hd0 -netdev user,id=net0 -device virtio-net-device,netdev=net0 -nographic
 
 The login prompt will appear in the terminal that started Qemu.
 
-Tested with QEMU 2.12.1
+Tested with QEMU 3.1
configs/qemu_riscv32_virt_defconfig +4 -1
index fab152e50a..5d3e06bf3c 100644
@@ -20,6 +20,9 @@ BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/riscv/riscv-linux.git"
 BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="8fe28cb58bcb235034b64cbbb7550a8a43fd88be"
 BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y
 BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="board/qemu/riscv32-virt/linux.config.fragment"
+BR2_LINUX_KERNEL_IMAGE=y
 
 # Bootloader
-BR2_TARGET_RISCV_PK=y
+BR2_TARGET_OPENSBI=y
+BR2_TARGET_OPENSBI_USE_PLAT=y
+BR2_TARGET_OPENSBI_PLAT="qemu/virt"
configs/qemu_riscv64_virt_defconfig +4 -1
index 596edf2fcd..05d2764003 100644
@@ -19,6 +19,9 @@ BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/riscv/riscv-linux.git"
 BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="8fe28cb58bcb235034b64cbbb7550a8a43fd88be"
 BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y
+BR2_LINUX_KERNEL_IMAGE=y
 
 # Bootloader
-BR2_TARGET_RISCV_PK=y
+BR2_TARGET_OPENSBI=y
+BR2_TARGET_OPENSBI_USE_PLAT=y
+BR2_TARGET_OPENSBI_PLAT="qemu/virt"
Signature · 1 line
2.21.0
#7 lore raw

PATCH v6 4/5 configs: qemu_riscv*_virt: Use OpenSBI by default

Quoted 9 lines · On Wed, 20 Mar 2019 23:05:21 +0000 Alistair Francis <[email protected]>…

Use OpenSBI by default instead of riscv-pk (BBL).

---
 board/qemu/riscv32-virt/readme.txt  | 6 +++---
 board/qemu/riscv64-virt/readme.txt  | 6 +++---
 configs/qemu_riscv32_virt_defconfig | 5 ++++-
 configs/qemu_riscv64_virt_defconfig | 5 ++++-
 4 files changed, 14 insertions(+), 8 deletions(-)

Applied to master, thanks.

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
#8 lore raw

PATCH v6 5/5 boot/riscv-pk: Deprecate riscv-pk and BBL

In reply to Alistair Francis
---
 boot/riscv-pk/Config.in | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
boot/riscv-pk/Config.in +4 -1
index b4fe36590f..cf9c5cd8ee 100644
@@ -3,10 +3,13 @@ comment "riscv-pk needs a Linux kernel to be built"
 	depends on !BR2_LINUX_KERNEL
 
 config BR2_TARGET_RISCV_PK
-	bool "riscv-pk"
+	bool "riscv-pk (deprecated)"
 	depends on BR2_riscv
 	depends on BR2_LINUX_KERNEL
 	help
+	  The RISC-V Proxy Kernel (pk) and Boot Loader (BBL) have
+	  been deprecated. Please use OpenSBI instead.
+
 	  The RISC-V Proxy Kernel (pk) package contains the Berkeley
 	  Boot Loader (BBL) which has been designed to boot a Linux
 	  kernel on a RISC-V processor.
Signature · 1 line
2.21.0
#9 lore raw

PATCH v6 5/5 boot/riscv-pk: Deprecate riscv-pk and BBL

Quoted 4 lines · On Wed, 20 Mar 2019 23:05:22 +0000 Alistair Francis <[email protected]>…
---
 boot/riscv-pk/Config.in | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

Applied to master, thanks.

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
#10 lore raw

PATCH v6 1/5 board/qemu/riscv32-virt: Convert defconfig into a fragment

In reply to Alistair Francis
Quoted 4 lines · On Wed, 20 Mar 2019 23:05:21 +0000 Alistair Francis <[email protected]>…

Convert the config to the arch defconfig plus a fragment. When this fragment is applied we will generate the same config as we previously did.

Quoted 8 lines
---
 board/qemu/riscv32-virt/linux.config          |  23 ----
 board/qemu/riscv32-virt/linux.config.fragment | 104 ++++++++++++++++++
 configs/qemu_riscv32_virt_defconfig           |   4 +-
 3 files changed, 106 insertions(+), 25 deletions(-)
 delete mode 100644 board/qemu/riscv32-virt/linux.config
 create mode 100644 board/qemu/riscv32-virt/linux.config.fragment

Applied to master, thanks.

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com