Skip to contentSkip to conversation

omapdrm: hdmi4_cec: Fix CEC clock handling for PM

PATCH In review Tony Lindgren 3 participants 3 messages Mar 26, 2019 – Mar 27, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 omapdrm: hdmi4_cec: Fix CEC clock handling for PM

If CONFIG_OMAP4_DSS_HDMI_CEC is enabled in .config, deeper SoC idle states are blocked because the CEC clock gets always enabled on init.

Let's fix the issue by moving the CEC clock handling to happen later in hdmi_cec_adap_enable() as suggested by Hans Verkuil <[email protected]>. This way the CEC clock gets only enabled when needed. This can be tested by doing cec-ctl --playback to enable the CEC, and doing cec-ctl --clear to disable it.

Let's also fix the typo for "divider" in the comments while at it.

Fixes 8d7f934df8d8 ("omapdrm: hdmi4_cec: add OMAP4 HDMI CEC support")
Cc Hans Verkuil <[email protected]>
Cc Jyri Sarha <[email protected]>
Cc Laurent Pinchart <[email protected]>

---

Changes since v1:

- Move clock enable to happen after the whole disable section rather than add a pointless test for enable as noted by Hans

- Move clock enable to happen after hdmi4_core_enable() as otherwise doing cec-ctl --playback with no HDMI cable connected will cause imprecise external abort as HDMI core is idled

- Disable CEC device on possible errors

---
 drivers/gpu/drm/omapdrm/dss/hdmi4_cec.c | 26 ++++++++++++++++++-------
 1 file changed, 19 insertions(+), 7 deletions(-)
drivers/gpu/drm/omapdrm/dss/hdmi4_cec.c +19 -7
@@ -175,6 +175,7 @@ static int hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
 		REG_FLD_MOD(core->base, HDMI_CORE_SYS_INTR_UNMASK4, 0, 3, 3);
 		hdmi_wp_clear_irqenable(core->wp, HDMI_IRQ_CORE);
 		hdmi_wp_set_irqstatus(core->wp, HDMI_IRQ_CORE);
+		REG_FLD_MOD(core->wp->base, HDMI_WP_CLK, 0, 5, 0);
 		hdmi4_core_disable(core);
 		return 0;
 	}
@@ -182,16 +183,24 @@ static int hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
 	if (err)
 		return err;
 
+	/*
+	 * Initialize CEC clock divider: CEC needs 2MHz clock hence
+	 * set the divider to 24 to get 48/24=2MHz clock
+	 */
+	REG_FLD_MOD(core->wp->base, HDMI_WP_CLK, 0x18, 5, 0);
+
 	/* Clear TX FIFO */
 	if (!hdmi_cec_clear_tx_fifo(adap)) {
 		pr_err("cec-%s: could not clear TX FIFO\n", adap->name);
-		return -EIO;
+		err = -EIO;
+		goto err_disable_clk;
 	}
 
 	/* Clear RX FIFO */
 	if (!hdmi_cec_clear_rx_fifo(adap)) {
 		pr_err("cec-%s: could not clear RX FIFO\n", adap->name);
-		return -EIO;
+		err = -EIO;
+		goto err_disable_clk;
 	}
 
 	/* Clear CEC interrupts */
@@ -236,6 +245,12 @@ static int hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
 		hdmi_write_reg(core->base, HDMI_CEC_INT_STATUS_1, temp);
 	}
 	return 0;
+
+err_disable_clk:
+	REG_FLD_MOD(core->wp->base, HDMI_WP_CLK, 0, 5, 0);
+	hdmi4_core_disable(core);
+
+	return err;
 }
 
 static int hdmi_cec_adap_log_addr(struct cec_adapter *adap, u8 log_addr)
@@ -333,11 +348,8 @@ int hdmi4_cec_init(struct platform_device *pdev, struct hdmi_core_data *core,
 		return ret;
 	core->wp = wp;
 
-	/*
-	 * Initialize CEC clock divider: CEC needs 2MHz clock hence
-	 * set the devider to 24 to get 48/24=2MHz clock
-	 */
-	REG_FLD_MOD(core->wp->base, HDMI_WP_CLK, 0x18, 5, 0);
+	/* Disable clock initially, hdmi_cec_adap_enable() manages it */
+	REG_FLD_MOD(core->wp->base, HDMI_WP_CLK, 0, 5, 0);
 
 	ret = cec_register_adapter(core->adap, &pdev->dev);
 	if (ret < 0) {
Signature · 5 lines
2.21.0
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Reviewed-by on v2 1/1
#1 lore raw
Quoted 9 lines · Tony Lindgren

If CONFIG_OMAP4_DSS_HDMI_CEC is enabled in .config, deeper SoC idle states are blocked because the CEC clock gets always enabled on init.

Let's fix the issue by moving the CEC clock handling to happen later in hdmi_cec_adap_enable() as suggested by Hans Verkuil <[email protected]>. This way the CEC clock gets only enabled when needed. This can be tested by doing cec-ctl --playback to enable the CEC, and doing cec-ctl --clear to disable it.

Quoted 8 lines

Let's also fix the typo for "divider" in the comments while at it.

Fixes 8d7f934df8d8 ("omapdrm: hdmi4_cec: add OMAP4 HDMI CEC support")
Cc Hans Verkuil <[email protected]>
Cc Jyri Sarha <[email protected]>
Cc Laurent Pinchart <[email protected]>

Thank you!

Regards,

Hans

Quoted 73 lines

---

Changes since v1:

- Move clock enable to happen after the whole disable section rather than add a pointless test for enable as noted by Hans

- Move clock enable to happen after hdmi4_core_enable() as otherwise doing cec-ctl --playback with no HDMI cable connected will cause imprecise external abort as HDMI core is idled

- Disable CEC device on possible errors

---
 drivers/gpu/drm/omapdrm/dss/hdmi4_cec.c | 26 ++++++++++++++++++-------
 1 file changed, 19 insertions(+), 7 deletions(-)
drivers/gpu/drm/omapdrm/dss/hdmi4_cec.c +17 -2
@@ -175,6 +175,7 @@ static int hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
 		REG_FLD_MOD(core->base, HDMI_CORE_SYS_INTR_UNMASK4, 0, 3, 3);
 		hdmi_wp_clear_irqenable(core->wp, HDMI_IRQ_CORE);
 		hdmi_wp_set_irqstatus(core->wp, HDMI_IRQ_CORE);
+		REG_FLD_MOD(core->wp->base, HDMI_WP_CLK, 0, 5, 0);
 		hdmi4_core_disable(core);
 		return 0;
 	}
@@ -182,16 +183,24 @@ static int hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
 	if (err)
 		return err;
 
+	/*
+	 * Initialize CEC clock divider: CEC needs 2MHz clock hence
+	 * set the divider to 24 to get 48/24=2MHz clock
+	 */
+	REG_FLD_MOD(core->wp->base, HDMI_WP_CLK, 0x18, 5, 0);
+
 	/* Clear TX FIFO */
 	if (!hdmi_cec_clear_tx_fifo(adap)) {
 		pr_err("cec-%s: could not clear TX FIFO\n", adap->name);
-		return -EIO;
+		err = -EIO;
+		goto err_disable_clk;
 	}
 
 	/* Clear RX FIFO */
 	if (!hdmi_cec_clear_rx_fifo(adap)) {
 		pr_err("cec-%s: could not clear RX FIFO\n", adap->name);
-		return -EIO;
+		err = -EIO;
+		goto err_disable_clk;
 	}
 
 	/* Clear CEC interrupts */
@@ -236,6 +245,12 @@ static int hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable)
 		hdmi_write_reg(core->base, HDMI_CEC_INT_STATUS_1, temp);
 	}
 	return 0;
+
+err_disable_clk:
+	REG_FLD_MOD(core->wp->base, HDMI_WP_CLK, 0, 5, 0);
+	hdmi4_core_disable(core);
+
+	return err;
 }
 
 static int hdmi_cec_adap_log_addr(struct cec_adapter *adap, u8 log_addr)
@@ -333,11 +348,8 @@ int hdmi4_cec_init(struct platform_device *pdev, struct hdmi_core_data *core,
 		return ret;
 	core->wp = wp;
 

drivers/gpu/drm/omapdrm/dss/hdmi4_cec.c int hdmi4_cec_init(struct platform_device *pdev, struct hdmi_core_data *core, · line 355

Quoted 10 lines
drivers/gpu/drm/omapdrm/dss/hdmi4_cec.c +2 -5
-	/*
-	 * Initialize CEC clock divider: CEC needs 2MHz clock hence
-	 * set the devider to 24 to get 48/24=2MHz clock
-	 */
-	REG_FLD_MOD(core->wp->base, HDMI_WP_CLK, 0x18, 5, 0);
+	/* Disable clock initially, hdmi_cec_adap_enable() manages it */
+	REG_FLD_MOD(core->wp->base, HDMI_WP_CLK, 0, 5, 0);
 
 	ret = cec_register_adapter(core->adap, &pdev->dev);
 	if (ret < 0) {

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#2 lore raw
In reply to Tony Lindgren
Quoted 11 lines · Tony Lindgren

If CONFIG_OMAP4_DSS_HDMI_CEC is enabled in .config, deeper SoC idle states are blocked because the CEC clock gets always enabled on init.

Let's fix the issue by moving the CEC clock handling to happen later in hdmi_cec_adap_enable() as suggested by Hans Verkuil <[email protected]>. This way the CEC clock gets only enabled when needed. This can be tested by doing cec-ctl --playback to enable the CEC, and doing cec-ctl --clear to disable it.

Let's also fix the typo for "divider" in the comments while at it.

Quoted 7 lines
Fixes 8d7f934df8d8 ("omapdrm: hdmi4_cec: add OMAP4 HDMI CEC support")
Cc Hans Verkuil <[email protected]>
Cc Jyri Sarha <[email protected]>
Cc Laurent Pinchart <[email protected]>

---

Thanks! I'll pick this up.

Tomi

Signature · 6 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel