Skip to contentSkip to conversation

ipmi_si: Fix crash when using hard-coded device

PATCH Applied [email protected] 2 participants 2 messages Mar 26, 2019 – Mar 27, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ipmi_si: Fix crash when using hard-coded device

From: Corey Minyard <[email protected]>

Backport from 41b766d661bf94a364960862cfc248a78313dbd3

When excuting a command like:
modprobe ipmi_si ports=0xffc0e3 type=bt
The system would get an oops.

The trouble here is that ipmi_si_hardcode_find_bmc() is called before ipmi_si_platform_init(), but initialization of the hard-coded device creates an IPMI platform device, which won't be initialized yet.

The real trouble is that hard-coded devices aren't created with any device, and the fixup is done later. So do it right, create the hard-coded devices as normal platform devices.

This required adding some new resource types to the IPMI platform code for passing information required by the hard-coded device and adding some code to remove the hard-coded platform devices on module removal.

To enforce the "hard-coded devices passed by the user take priority over firmware devices" rule, some special code was added to check and see if a hard-coded device already exists.

The backport required some minor fixups and adding the device id table that had been added in another change and was used in this one.

---

This backport is for 4.19, the backport from the main tree failed. Passes basic tests.

 drivers/char/ipmi/ipmi_si.h          |   4 +-
 drivers/char/ipmi/ipmi_si_hardcode.c | 236 ++++++++++++++++++++-------
 drivers/char/ipmi/ipmi_si_intf.c     |  22 ++-
 drivers/char/ipmi/ipmi_si_platform.c |  30 +++-
 4 files changed, 218 insertions(+), 74 deletions(-)
drivers/char/ipmi/ipmi_si.h +3 -1
index 52f6152d1fcb..7ae52c17618e 100644
@@ -25,7 +25,9 @@ void ipmi_irq_finish_setup(struct si_sm_io *io);
 int ipmi_si_remove_by_dev(struct device *dev);
 void ipmi_si_remove_by_data(int addr_space, enum si_type si_type,
 			    unsigned long addr);
-int ipmi_si_hardcode_find_bmc(void);
+void ipmi_hardcode_init(void);
+void ipmi_si_hardcode_exit(void);
+int ipmi_si_hardcode_match(int addr_type, unsigned long addr);
 void ipmi_si_platform_init(void);
 void ipmi_si_platform_shutdown(void);
 
drivers/char/ipmi/ipmi_si_hardcode.c +174 -62

269 lines not on this page · raw message

drivers/char/ipmi/ipmi_si_intf.c +16 -6
index 82d831b103f9..75e5006f395a 100644
@@ -1862,6 +1862,18 @@ int ipmi_si_add_smi(struct si_sm_io *io)
 	int rv = 0;
 	struct smi_info *new_smi, *dup;
 
+	/*
+	 * If the user gave us a hard-coded device at the same
+	 * address, they presumably want us to use it and not what is
+	 * in the firmware.
+	 */
+	if (io->addr_source != SI_HARDCODED &&
+	    ipmi_si_hardcode_match(io->addr_type, io->addr_data)) {
+		dev_info(io->dev,
+			 "Hard-coded device at this address already exists");
+		return -ENODEV;
+	}
+
 	if (!io->io_setup) {
 		if (io->addr_type == IPMI_IO_ADDR_SPACE) {
 			io->io_setup = ipmi_si_port_setup;
@@ -2094,7 +2106,7 @@ static int try_smi_init(struct smi_info *new_smi)
 	return rv;
 }
 
-static int init_ipmi_si(void)
+static int __init init_ipmi_si(void)
 {
 	struct smi_info *e;
 	enum ipmi_addr_src type = SI_INVALID;
@@ -2102,12 +2114,9 @@ static int init_ipmi_si(void)
 	if (initialized)
 		return 0;
 
+	ipmi_hardcode_init();
 	pr_info("IPMI System Interface driver.\n");
 
-	/* If the user gave us a device, they presumably want us to use it */
-	if (!ipmi_si_hardcode_find_bmc())
-		goto do_scan;
-
 	ipmi_si_platform_init();
 
 	ipmi_si_pci_init();
@@ -2118,7 +2127,6 @@ static int init_ipmi_si(void)
 	   with multiple BMCs we assume that there will be several instances
 	   of a given type so if we succeed in registering a type then also
 	   try to register everything else of the same type */
-do_scan:
 	mutex_lock(&smi_infos_lock);
 	list_for_each_entry(e, &smi_infos, link) {
 		/* Try to register a device if it has an IRQ and we either
@@ -2304,6 +2312,8 @@ static void cleanup_ipmi_si(void)
 	list_for_each_entry_safe(e, tmp_e, &smi_infos, link)
 		cleanup_one_si(e);
 	mutex_unlock(&smi_infos_lock);
+
+	ipmi_si_hardcode_exit();
 }
 module_exit(cleanup_ipmi_si);
 
drivers/char/ipmi/ipmi_si_platform.c +25 -5
index bf69927502bd..d32b0dd377c5 100644
@@ -126,8 +126,6 @@ ipmi_get_info_from_resources(struct platform_device *pdev,
 		if (res_second->start > io->addr_data)
 			io->regspacing = res_second->start - io->addr_data;
 	}
-	io->regsize = DEFAULT_REGSIZE;
-	io->regshift = 0;
 
 	return res;
 }
@@ -135,7 +133,7 @@ ipmi_get_info_from_resources(struct platform_device *pdev,
 static int platform_ipmi_probe(struct platform_device *pdev)
 {
 	struct si_sm_io io;
-	u8 type, slave_addr, addr_source;
+	u8 type, slave_addr, addr_source, regsize, regshift;
 	int rv;
 
 	rv = device_property_read_u8(&pdev->dev, "addr-source", &addr_source);
@@ -147,7 +145,7 @@ static int platform_ipmi_probe(struct platform_device *pdev)
 	if (addr_source == SI_SMBIOS) {
 		if (!si_trydmi)
 			return -ENODEV;
-	} else {
+	} else if (addr_source != SI_HARDCODED) {
 		if (!si_tryplatform)
 			return -ENODEV;
 	}
@@ -167,11 +165,23 @@ static int platform_ipmi_probe(struct platform_device *pdev)
 	case SI_BT:
 		io.si_type = type;
 		break;
+	case SI_TYPE_INVALID: /* User disabled this in hardcode. */
+		return -ENODEV;
 	default:
 		dev_err(&pdev->dev, "ipmi-type property is invalid\n");
 		return -EINVAL;
 	}
 
+	io.regsize = DEFAULT_REGSIZE;
+	rv = device_property_read_u8(&pdev->dev, "reg-size", &regsize);
+	if (!rv)
+		io.regsize = regsize;
+
+	io.regshift = 0;
+	rv = device_property_read_u8(&pdev->dev, "reg-shift", &regshift);
+	if (!rv)
+		io.regshift = regshift;
+
 	if (!ipmi_get_info_from_resources(pdev, &io))
 		return -EINVAL;
 
@@ -191,7 +201,8 @@ static int platform_ipmi_probe(struct platform_device *pdev)
 
 	io.dev = &pdev->dev;
 
-	pr_info("ipmi_si: SMBIOS: %s %#lx regsize %d spacing %d irq %d\n",
+	pr_info("ipmi_si: %s: %s %#lx regsize %d spacing %d irq %d\n",
+		ipmi_addr_src_to_str(addr_source),
 		(io.addr_type == IPMI_IO_ADDR_SPACE) ? "io" : "mem",
 		io.addr_data, io.regsize, io.regspacing, io.irq);
 
@@ -356,6 +367,9 @@ static int acpi_ipmi_probe(struct platform_device *pdev)
 		goto err_free;
 	}
 
+	io.regsize = DEFAULT_REGSIZE;
+	io.regshift = 0;
+
 	res = ipmi_get_info_from_resources(pdev, &io);
 	if (!res) {
 		rv = -EINVAL;
@@ -417,6 +431,11 @@ static int ipmi_remove(struct platform_device *pdev)
 	return ipmi_si_remove_by_dev(&pdev->dev);
 }
 
+static const struct platform_device_id si_plat_ids[] = {
+    { "hardcode-ipmi-si", 0 },
+    { }
+};
+
 struct platform_driver ipmi_platform_driver = {
 	.driver = {
 		.name = DEVICE_NAME,
@@ -425,6 +444,7 @@ struct platform_driver ipmi_platform_driver = {
 	},
 	.probe		= ipmi_probe,
 	.remove		= ipmi_remove,
+	.id_table       = si_plat_ids
 };
 
 void ipmi_si_platform_init(void)
Signature · 1 line
2.17.1
maintainer Applied
#1 lore raw
Quoted 29 lines · On Tue, Mar 26, 2019 at 11:10:04AM -0500, [email protected] wrote:

From: Corey Minyard <[email protected]>

Backport from 41b766d661bf94a364960862cfc248a78313dbd3

When excuting a command like:
modprobe ipmi_si ports=0xffc0e3 type=bt
The system would get an oops.

The trouble here is that ipmi_si_hardcode_find_bmc() is called before ipmi_si_platform_init(), but initialization of the hard-coded device creates an IPMI platform device, which won't be initialized yet.

The real trouble is that hard-coded devices aren't created with any device, and the fixup is done later. So do it right, create the hard-coded devices as normal platform devices.

This required adding some new resource types to the IPMI platform code for passing information required by the hard-coded device and adding some code to remove the hard-coded platform devices on module removal.

To enforce the "hard-coded devices passed by the user take priority over firmware devices" rule, some special code was added to check and see if a hard-coded device already exists.

The backport required some minor fixups and adding the device id table that had been added in another change and was used in this one.

Quoted 8 lines

---

This backport is for 4.19, the backport from the main tree failed. Passes basic tests.

Queued for 4.19, thank you.

--
Thanks,
Sasha