ARM: dts: am43xx-epos-evm: Keep DCDC5 and DCDC6 always on
Subsystems (5)
PATCH 1/5 ARM: dts: am43xx-epos-evm: Keep DCDC5 and DCDC6 always on
From: Kabir Sahane <[email protected]>
These regulator outputs are needed even in deep sleep modes to prevent low-voltage detection events. Make these always ON to avoid this.
--- arch/arm/boot/dts/am43x-epos-evm.dts | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm/boot/dts/am43x-epos-evm.dts +4 -0
@@ -634,12 +634,16 @@ regulator-name = "v1_0bat"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; + regulator-boot-on; + regulator-always-on; }; dcdc6: regulator-dcdc6 { regulator-name = "v1_8bat"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; }; ldo1: regulator-ldo1 {
Signature · 1 line
2.21.0
PATCH 2/5 ARM: dts: am43xx-epos-evm: Keep DCDC3 regulator on in suspend to memory
From: Mike Erdahl <[email protected]>
When going to suspend to ram mode (or rtc-only mode), the DDR regulator must be told to stay on, else this rail will go down when the PMIC_EN signal is deasserted.
--- arch/arm/boot/dts/am43x-epos-evm.dts | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/boot/dts/am43x-epos-evm.dts +6 -0
@@ -620,6 +620,12 @@ regulator-name = "vdcdc3"; regulator-boot-on; regulator-always-on; + regulator-state-mem { + regulator-on-in-suspend; + }; + regulator-state-disk { + regulator-off-in-suspend; + }; }; dcdc4: regulator-dcdc4 {
Signature · 1 line
2.21.0
PATCH 3/5 ARM: dts: am43xx-epos-evm: Add matrix keypad as wakeup source
In reply to Andrew F. DavisMark matrix-keypad as a wakeup source.
--- arch/arm/boot/dts/am43x-epos-evm.dts | 1 + 1 file changed, 1 insertion(+)
arch/arm/boot/dts/am43x-epos-evm.dts +1 -0
@@ -80,6 +80,7 @@ pinctrl-names = "default", "sleep"; pinctrl-0 = <&matrix_keypad_default>; pinctrl-1 = <&matrix_keypad_sleep>; + wakeup-source; row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH /* Bank0, pin12 */ &gpio0 13 GPIO_ACTIVE_HIGH /* Bank0, pin13 */
Signature · 1 line
2.21.0
PATCH 4/5 ARM: OMAP: Wakeupgen: AM43xx HS devices should save context like non-HS
In reply to Andrew F. DavisUnlike some previous generation devices, AM43xx HS IRQ and Wakegen context is handled by the ROM for us, and no secure service call is needed or supported. Non-GP AM43xx devices should take the same path as GP.
--- arch/arm/mach-omap2/omap-wakeupgen.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/mach-omap2/omap-wakeupgen.c +2 -2
@@ -436,13 +436,13 @@ static int irq_notifier(struct notifier_block *self, unsigned long cmd, void *v) {switch (cmd) {case CPU_CLUSTER_PM_ENTER : -if (omap_type () ==OMAP2_DEVICE_TYPE_GP ) +if (omap_type () ==OMAP2_DEVICE_TYPE_GP ||soc_is_am43xx ())irq_save_context ();else irq_save_secure_context ();break ;case CPU_CLUSTER_PM_EXIT : -if (omap_type () ==OMAP2_DEVICE_TYPE_GP ) +if (omap_type () ==OMAP2_DEVICE_TYPE_GP ||soc_is_am43xx ())irq_restore_context ();break ; }
Signature · 1 line
2.21.0
Tony Lindgren
maintainerRe: [PATCH 4/5] ARM: OMAP: Wakeupgen: AM43xx HS devices should save context like non-HS
Quoted 4 lines · Andrew F. Davis
Unlike some previous generation devices, AM43xx HS IRQ and Wakegen context is handled by the ROM for us, and no secure service call is needed or supported. Non-GP AM43xx devices should take the same path as GP.
Applying the two SoC related changes into omap-for-v5.2/soc.
Tony
PATCH 5/5 ARM: OMAP2+: pm33xx-core: Do not Turn OFF CEFUSE as PPA may be using it
In reply to Andrew F. DavisFrom: Kabir Sahane <[email protected]>
This area is used to store keys by HSPPA in case of AM438x SOC. Leave it active.
--- arch/arm/mach-omap2/pm33xx-core.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
arch/arm/mach-omap2/pm33xx-core.c +5 -3
@@ -51,10 +51,12 @@ static int amx3_common_init(void)/* CEFUSE domain can be turned off post bootup */ cefuse_pwrdm =pwrdm_lookup ("cefuse_pwrdm" ); -if (cefuse_pwrdm) -omap_set_pwrdm_state (cefuse_pwrdm,PWRDM_POWER_OFF ); -else +if (!cefuse_pwrdm)pr_err ("PM: Failed to get cefuse_pwrdm\n" ); +else if (omap_type () !=OMAP2_DEVICE_TYPE_GP ) +pr_info ("PM: Leaving EFUSE power domain active\n" ); +else +omap_set_pwrdm_state (cefuse_pwrdm,PWRDM_POWER_OFF );return 0 ; }
Signature · 1 line
2.21.0
Tony Lindgren
maintainerQuoted 4 lines · Andrew F. Davis
From: Kabir Sahane <[email protected]>
These regulator outputs are needed even in deep sleep modes to prevent low-voltage detection events. Make these always ON to avoid this.
Thanks applying the three dts changes into omap-for-v5.2/dt.
Regards,
Tony