Skip to contentSkip to conversation

x86/boot: This program cannot be run in DOS mode.$

PATCH In review Pali Rohár 3 participants 5 messages Apr 1, 2019 – Apr 18, 2019 x86

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 x86/boot: This program cannot be run in DOS mode.$

Every EFI binary is in PE format. And we know that PE format needs to have MZ MS-DOS header as there is written offset to PE header.

Therefore generated bzImage binary with CONFIG_EFI_STUB option is MS-DOS executable binary.

We already know the "requirement" that Windows PE executable started in MS-DOS must print legendary and famous message to computer screen:
"This program cannot be run in DOS mode."

But trying to run that bzImage of Linux kernel with MZ header just cause freezing whole MS-DOS instead of writing "the correct message" to user. This is not the compliant behavior of PE executables!

This patch fixes this problem. When Linux kernel compiled with CONFIG_EFI_STUB is started in MS-DOS then it prints message:

This program cannot be run in DOS mode.
To load Linux kernel from DOS mode use LOADLIN.EXE.

So it also helps MS-DOS users how to "correctly" start this bzImage binary by mentioning LOADLIN.EXE. Note that MS-DOS strings are not null-terminated but rather dollar-terminated.

To have error message unified bugger_off_msg for BIOS boot block code was changed to:

This program cannot be run in BIOS mode.

So if you copy generated bzImage directly to boot sector and try to boot it by BIOS you get this new updated message.

Due to fixed offset of setup header (0x1f1), PE header was moved after entrytext section. bstext and bsdata sections where is full MZ header and MS-DOS code is now bigger.

---
 arch/x86/boot/header.S | 55 +++++++++++++++++++++++++++++++++++++++++++-------
 arch/x86/boot/setup.ld |  1 +
 2 files changed, 49 insertions(+), 7 deletions(-)
arch/x86/boot/header.S +48 -7
index 850b8762e889..58fcab7d00c8 100644
@@ -45,6 +45,46 @@ bootsect_start:
 	# "MZ", MS-DOS header
 	.byte 0x4d
 	.byte 0x5a
+
+	# Explicitly enter this as bytes, or the assembler
+	# tries to generate a 3-byte jump here, which causes
+	# everything else to push off to the wrong offset.
+	.byte	0xeb    # short (2-byte) jump
+	.byte	bios_start-1f
+1:
+
+	.org	0x04
+	.short	3       # e_cp - Pages in file
+	.short	0       # e_crlc - Relocations
+	.short	4       # e_cparhdr - Size of header in paragraphs
+	.short	0       # e_minalloc - Minimum extra paragraphs needed
+	.short	0xffff  # e_maxalloc - Maximum extra paragraphs needed
+	.short	0       # e_ss - Initial (relative) SS value
+	.short	0       # e_sp - Initial SP value
+	.short	0       # e_csum - Checksum
+	.short	0       # e_ip - Initial IP value
+	.short	-4      # e_cs - Initial (relative) CS value
+	.short	0x40    # e_lfarlc - File address of relocation table
+
+	.org	0x3c
+	.long	pe_header  # Offset to the PE header
+
+	#
+	# MS-DOS start code
+	#
+	push	%cs
+	pop	%ds
+
+	# Write msdos_msg string
+	mov	$msdos_msg, %dx
+	mov	$0x09, %ah
+	int	$0x21
+
+	# Terminate program
+	mov	$0x4c01, %ax
+	int	$0x21
+
+bios_start:
 #endif
 
 	# Normalize the start address
@@ -80,22 +120,23 @@ bs_die:
 	# invoke the BIOS reset code...
 	ljmp	$0xf000,$0xfff0
 
+	.section ".bsdata", "a"
 #ifdef CONFIG_EFI_STUB
-	.org	0x3c
-	#
-	# Offset to the PE header.
-	#
-	.long	pe_header
+msdos_msg:
+	.ascii	"This program cannot be run in DOS mode.\r\n"
+	.ascii	"To load Linux kernel from DOS mode use LOADLIN.EXE.\r\r\n"
+	.ascii	"$"
 #endif /* CONFIG_EFI_STUB */
 
-	.section ".bsdata", "a"
 bugger_off_msg:
-	.ascii	"Use a boot loader.\r\n"
+	.ascii	"This program cannot be run in BIOS mode.\r\n"
+	.ascii	"To load Linux kernel from BIOS mode use a boot loader.\r\n"
 	.ascii	"\n"
 	.ascii	"Remove disk and press any key to reboot...\r\n"
 	.byte	0
 
 #ifdef CONFIG_EFI_STUB
+	.section ".pedata", "a"
 pe_header:
 	.ascii	"PE"
 	.word 	0
arch/x86/boot/setup.ld +1 -0
index 0149e41d42c2..c0ec2fe09d2d 100644
@@ -16,6 +16,7 @@ SECTIONS
 	. = 495;
 	.header		: { *(.header) }
 	.entrytext	: { *(.entrytext) }
+	.pedata		: { *(.pedata) }
 	.inittext	: { *(.inittext) }
 	.initdata	: { *(.initdata) }
 	__end_init = .;
Signature · 1 line
2.11.0
#1 lore raw
Quoted 27 lines · Pali Rohár

Every EFI binary is in PE format. And we know that PE format needs to have MZ MS-DOS header as there is written offset to PE header.

Therefore generated bzImage binary with CONFIG_EFI_STUB option is MS-DOS executable binary.

We already know the "requirement" that Windows PE executable started in MS-DOS must print legendary and famous message to computer screen:
"This program cannot be run in DOS mode."

But trying to run that bzImage of Linux kernel with MZ header just cause freezing whole MS-DOS instead of writing "the correct message" to user. This is not the compliant behavior of PE executables!

This patch fixes this problem. When Linux kernel compiled with CONFIG_EFI_STUB is started in MS-DOS then it prints message:

This program cannot be run in DOS mode.
To load Linux kernel from DOS mode use LOADLIN.EXE.

So it also helps MS-DOS users how to "correctly" start this bzImage binary by mentioning LOADLIN.EXE. Note that MS-DOS strings are not null-terminated but rather dollar-terminated.

To have error message unified bugger_off_msg for BIOS boot block code was changed to:

Quoted 8 lines

This program cannot be run in BIOS mode.

So if you copy generated bzImage directly to boot sector and try to boot it by BIOS you get this new updated message.

Due to fixed offset of setup header (0x1f1), PE header was moved after entrytext section. bstext and bsdata sections where is full MZ header and MS-DOS code is now bigger.

Hehe, I guess the patch may have been dropped due to april's fools?

You may want to retransmit?
Pavel

Quoted 100 lines
---
 arch/x86/boot/header.S | 55 +++++++++++++++++++++++++++++++++++++++++++-------
 arch/x86/boot/setup.ld |  1 +
 2 files changed, 49 insertions(+), 7 deletions(-)
arch/x86/boot/header.S +48 -7
index 850b8762e889..58fcab7d00c8 100644
@@ -45,6 +45,46 @@ bootsect_start:
 	# "MZ", MS-DOS header
 	.byte 0x4d
 	.byte 0x5a
+
+	# Explicitly enter this as bytes, or the assembler
+	# tries to generate a 3-byte jump here, which causes
+	# everything else to push off to the wrong offset.
+	.byte	0xeb    # short (2-byte) jump
+	.byte	bios_start-1f
+1:
+
+	.org	0x04
+	.short	3       # e_cp - Pages in file
+	.short	0       # e_crlc - Relocations
+	.short	4       # e_cparhdr - Size of header in paragraphs
+	.short	0       # e_minalloc - Minimum extra paragraphs needed
+	.short	0xffff  # e_maxalloc - Maximum extra paragraphs needed
+	.short	0       # e_ss - Initial (relative) SS value
+	.short	0       # e_sp - Initial SP value
+	.short	0       # e_csum - Checksum
+	.short	0       # e_ip - Initial IP value
+	.short	-4      # e_cs - Initial (relative) CS value
+	.short	0x40    # e_lfarlc - File address of relocation table
+
+	.org	0x3c
+	.long	pe_header  # Offset to the PE header
+
+	#
+	# MS-DOS start code
+	#
+	push	%cs
+	pop	%ds
+
+	# Write msdos_msg string
+	mov	$msdos_msg, %dx
+	mov	$0x09, %ah
+	int	$0x21
+
+	# Terminate program
+	mov	$0x4c01, %ax
+	int	$0x21
+
+bios_start:
 #endif
 
 	# Normalize the start address
@@ -80,22 +120,23 @@ bs_die:
 	# invoke the BIOS reset code...
 	ljmp	$0xf000,$0xfff0
 
+	.section ".bsdata", "a"
 #ifdef CONFIG_EFI_STUB
-	.org	0x3c
-	#
-	# Offset to the PE header.
-	#
-	.long	pe_header
+msdos_msg:
+	.ascii	"This program cannot be run in DOS mode.\r\n"
+	.ascii	"To load Linux kernel from DOS mode use LOADLIN.EXE.\r\r\n"
+	.ascii	"$"
 #endif /* CONFIG_EFI_STUB */
 
-	.section ".bsdata", "a"
 bugger_off_msg:
-	.ascii	"Use a boot loader.\r\n"
+	.ascii	"This program cannot be run in BIOS mode.\r\n"
+	.ascii	"To load Linux kernel from BIOS mode use a boot loader.\r\n"
 	.ascii	"\n"
 	.ascii	"Remove disk and press any key to reboot...\r\n"
 	.byte	0
 
 #ifdef CONFIG_EFI_STUB
+	.section ".pedata", "a"
 pe_header:
 	.ascii	"PE"
 	.word 	0
arch/x86/boot/setup.ld +1 -0
index 0149e41d42c2..c0ec2fe09d2d 100644
@@ -16,6 +16,7 @@ SECTIONS
 	. = 495;
 	.header		: { *(.header) }
 	.entrytext	: { *(.entrytext) }
+	.pedata		: { *(.pedata) }
 	.inittext	: { *(.inittext) }
 	.initdata	: { *(.initdata) }
 	__end_init = .;
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
#2 lore raw
Quoted 30 lines · On Monday 08 April 2019 20:04:22 Pavel Machek wrote:
Quoted 29 lines · Pali Rohár

Every EFI binary is in PE format. And we know that PE format needs to have MZ MS-DOS header as there is written offset to PE header.

Therefore generated bzImage binary with CONFIG_EFI_STUB option is MS-DOS executable binary.

We already know the "requirement" that Windows PE executable started in MS-DOS must print legendary and famous message to computer screen:
"This program cannot be run in DOS mode."

But trying to run that bzImage of Linux kernel with MZ header just cause freezing whole MS-DOS instead of writing "the correct message" to user. This is not the compliant behavior of PE executables!

This patch fixes this problem. When Linux kernel compiled with CONFIG_EFI_STUB is started in MS-DOS then it prints message:

This program cannot be run in DOS mode.
To load Linux kernel from DOS mode use LOADLIN.EXE.

So it also helps MS-DOS users how to "correctly" start this bzImage binary by mentioning LOADLIN.EXE. Note that MS-DOS strings are not null-terminated but rather dollar-terminated.

To have error message unified bugger_off_msg for BIOS boot block code was changed to:

This program cannot be run in BIOS mode.

Quoted 8 lines
Quoted 6 lines

So if you copy generated bzImage directly to boot sector and try to boot it by BIOS you get this new updated message.

Due to fixed offset of setup header (0x1f1), PE header was moved after entrytext section. bstext and bsdata sections where is full MZ header and MS-DOS code is now bigger.

Hehe, I guess the patch may have been dropped due to april's fools?

Yea, it was mean as first April patch :-) I tested it with MS-DOS 7.0 and DOSBox and it worked.

Quoted 1 line

You may want to retransmit?

Do you really think it can be useful? :-)

Quoted 103 lines

Pavel

Quoted 100 lines
---
 arch/x86/boot/header.S | 55 +++++++++++++++++++++++++++++++++++++++++++-------
 arch/x86/boot/setup.ld |  1 +
 2 files changed, 49 insertions(+), 7 deletions(-)
arch/x86/boot/header.S +48 -7
index 850b8762e889..58fcab7d00c8 100644
@@ -45,6 +45,46 @@ bootsect_start:
 	# "MZ", MS-DOS header
 	.byte 0x4d
 	.byte 0x5a
+
+	# Explicitly enter this as bytes, or the assembler
+	# tries to generate a 3-byte jump here, which causes
+	# everything else to push off to the wrong offset.
+	.byte	0xeb    # short (2-byte) jump
+	.byte	bios_start-1f
+1:
+
+	.org	0x04
+	.short	3       # e_cp - Pages in file
+	.short	0       # e_crlc - Relocations
+	.short	4       # e_cparhdr - Size of header in paragraphs
+	.short	0       # e_minalloc - Minimum extra paragraphs needed
+	.short	0xffff  # e_maxalloc - Maximum extra paragraphs needed
+	.short	0       # e_ss - Initial (relative) SS value
+	.short	0       # e_sp - Initial SP value
+	.short	0       # e_csum - Checksum
+	.short	0       # e_ip - Initial IP value
+	.short	-4      # e_cs - Initial (relative) CS value
+	.short	0x40    # e_lfarlc - File address of relocation table
+
+	.org	0x3c
+	.long	pe_header  # Offset to the PE header
+
+	#
+	# MS-DOS start code
+	#
+	push	%cs
+	pop	%ds
+
+	# Write msdos_msg string
+	mov	$msdos_msg, %dx
+	mov	$0x09, %ah
+	int	$0x21
+
+	# Terminate program
+	mov	$0x4c01, %ax
+	int	$0x21
+
+bios_start:
 #endif
 
 	# Normalize the start address
@@ -80,22 +120,23 @@ bs_die:
 	# invoke the BIOS reset code...
 	ljmp	$0xf000,$0xfff0
 
+	.section ".bsdata", "a"
 #ifdef CONFIG_EFI_STUB
-	.org	0x3c
-	#
-	# Offset to the PE header.
-	#
-	.long	pe_header
+msdos_msg:
+	.ascii	"This program cannot be run in DOS mode.\r\n"
+	.ascii	"To load Linux kernel from DOS mode use LOADLIN.EXE.\r\r\n"
+	.ascii	"$"
 #endif /* CONFIG_EFI_STUB */
 
-	.section ".bsdata", "a"
 bugger_off_msg:
-	.ascii	"Use a boot loader.\r\n"
+	.ascii	"This program cannot be run in BIOS mode.\r\n"
+	.ascii	"To load Linux kernel from BIOS mode use a boot loader.\r\n"
 	.ascii	"\n"
 	.ascii	"Remove disk and press any key to reboot...\r\n"
 	.byte	0
 
 #ifdef CONFIG_EFI_STUB
+	.section ".pedata", "a"
 pe_header:
 	.ascii	"PE"
 	.word 	0
arch/x86/boot/setup.ld +1 -0
index 0149e41d42c2..c0ec2fe09d2d 100644
@@ -16,6 +16,7 @@ SECTIONS
 	. = 495;
 	.header		: { *(.header) }
 	.entrytext	: { *(.entrytext) }
+	.pedata		: { *(.pedata) }
 	.inittext	: { *(.inittext) }
 	.initdata	: { *(.initdata) }
 	__end_init = .;
Signature · 2 lines
Pali Rohár
[email protected]
#3 lore raw
Quoted 38 lines · Pali Rohár
Quoted 37 lines · On Monday 08 April 2019 20:04:22 Pavel Machek wrote:
Quoted 35 lines · Pali Rohár

Every EFI binary is in PE format. And we know that PE format needs to have MZ MS-DOS header as there is written offset to PE header.

Therefore generated bzImage binary with CONFIG_EFI_STUB option is MS-DOS executable binary.

We already know the "requirement" that Windows PE executable started in MS-DOS must print legendary and famous message to computer screen:
"This program cannot be run in DOS mode."

But trying to run that bzImage of Linux kernel with MZ header just cause freezing whole MS-DOS instead of writing "the correct message" to user. This is not the compliant behavior of PE executables!

This patch fixes this problem. When Linux kernel compiled with CONFIG_EFI_STUB is started in MS-DOS then it prints message:

This program cannot be run in DOS mode.
To load Linux kernel from DOS mode use LOADLIN.EXE.

So it also helps MS-DOS users how to "correctly" start this bzImage binary by mentioning LOADLIN.EXE. Note that MS-DOS strings are not null-terminated but rather dollar-terminated.

To have error message unified bugger_off_msg for BIOS boot block code was changed to:

This program cannot be run in BIOS mode.

So if you copy generated bzImage directly to boot sector and try to boot it by BIOS you get this new updated message.

Due to fixed offset of setup header (0x1f1), PE header was moved after entrytext section. bstext and bsdata sections where is full MZ header and MS-DOS code is now bigger.

Quoted 8 lines
Quoted 1 line

Hehe, I guess the patch may have been dropped due to april's fools?

Yea, it was mean as first April patch :-) I tested it with MS-DOS 7.0 and DOSBox and it worked.

Quoted 1 line

You may want to retransmit?

Do you really think it can be useful? :-)

Dunno. It is quite simple, and quite a nice hack ;-).

Pavel

Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
#4 lore raw
Quoted 41 lines · Pavel Machek
Quoted 40 lines · Pali Rohár
Quoted 38 lines · On Monday 08 April 2019 20:04:22 Pavel Machek wrote:
Quoted 27 lines · Pali Rohár

Every EFI binary is in PE format. And we know that PE format needs to have MZ MS-DOS header as there is written offset to PE header.

Therefore generated bzImage binary with CONFIG_EFI_STUB option is MS-DOS executable binary.

We already know the "requirement" that Windows PE executable started in MS-DOS must print legendary and famous message to computer screen:
"This program cannot be run in DOS mode."

But trying to run that bzImage of Linux kernel with MZ header just cause freezing whole MS-DOS instead of writing "the correct message" to user. This is not the compliant behavior of PE executables!

This patch fixes this problem. When Linux kernel compiled with CONFIG_EFI_STUB is started in MS-DOS then it prints message:

This program cannot be run in DOS mode.
To load Linux kernel from DOS mode use LOADLIN.EXE.

So it also helps MS-DOS users how to "correctly" start this bzImage binary by mentioning LOADLIN.EXE. Note that MS-DOS strings are not null-terminated but rather dollar-terminated.

To have error message unified bugger_off_msg for BIOS boot block code was changed to:

Quoted 8 lines

This program cannot be run in BIOS mode.

So if you copy generated bzImage directly to boot sector and try to boot it by BIOS you get this new updated message.

Due to fixed offset of setup header (0x1f1), PE header was moved after entrytext section. bstext and bsdata sections where is full MZ header and MS-DOS code is now bigger.

Hehe, I guess the patch may have been dropped due to april's fools?

Quoted 8 lines
Quoted 6 lines

Yea, it was mean as first April patch :-) I tested it with MS-DOS 7.0 and DOSBox and it worked.

Quoted 1 line

You may want to retransmit?

Do you really think it can be useful? :-)

Dunno. It is quite simple, and quite a nice hack ;-).

Agreed, looks simple enough, no objections from me! :)

Ingo