Skip to contentSkip to conversation

usb: host: xhci-tegra: Add Tegra186 XUSB support

PATCH In review Thierry Reding 2 participants 10 messages Apr 1, 2019 – Apr 8, 2019

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v2 cover usb: host: xhci-tegra: Add Tegra186 XUSB support

From: Thierry Reding <[email protected]>

Hi,

This series introduces support for XUSB to the Tegra186 SoC. This is mostly the same as on earlier generations in that it provides an XHCI compatible interface with a bit of vendor-specific glue. Perhaps the most notable change is the removal of the IPFS wrapper. Patches for the UPHY related changes that control the PHYs for the XUSB controller were merged into v5.1.

This version is a rebase of the series posted here:

    http://patchwork.ozlabs.org/project/linux-tegra/list/?series=88193

There have been no code changes and I collected Reviewed-by and Acked-by tags.

Greg, can you pick up patches 1-3 with Rob's and Mathias' Acked-by, respectively? I'll pick up patches 4-6 into the Tegra tree.

Thanks,
Thierry

JC Kuo (2):
usb: host: xhci-tegra: Selectively program IPFS
usb: host: xhci-tegra: Add Tegra186 XUSB support

Thierry Reding (4):
dt-bindings: usb: xhci-tegra: Add Tegra186 support
arm64: tegra: Add XUSB and pad controller on Tegra186
arm64: tegra: Enable XUSB on P2771
arm64: tegra: Remove regulator hacks on Jetson TX2

 .../bindings/usb/nvidia,tegra124-xusb.txt     |   4 +
 .../boot/dts/nvidia/tegra186-p2771-0000.dts   | 115 +++++++++++++++
 .../arm64/boot/dts/nvidia/tegra186-p3310.dtsi |  42 ++----
 arch/arm64/boot/dts/nvidia/tegra186.dtsi      | 135 ++++++++++++++++++
 drivers/usb/host/xhci-tegra.c                 |  68 ++++++---
 5 files changed, 320 insertions(+), 44 deletions(-)
Signature · 1 line
2.21.0
#1 lore raw

PATCH v2 1/6 dt-bindings: usb: xhci-tegra: Add Tegra186 support

From: Thierry Reding <[email protected]>

Extend the bindings to cover the set of features found in Tegra186.

---
 .../devicetree/bindings/usb/nvidia,tegra124-xusb.txt          | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt +4 -0
index 4156c3e181c5..5bfcc0b4d6b9 100644
@@ -10,6 +10,7 @@ Required properties:
   - Tegra124: "nvidia,tegra124-xusb"
   - Tegra132: "nvidia,tegra132-xusb", "nvidia,tegra124-xusb"
   - Tegra210: "nvidia,tegra210-xusb"
+  - Tegra186: "nvidia,tegra186-xusb"
 - reg: Must contain the base and length of the xHCI host registers, XUSB FPCI
   registers and XUSB IPFS registers.
 - reg-names: Must contain the following entries:
@@ -59,6 +60,8 @@ For Tegra210:
 - avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V.
 - dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V.
 - hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V.
+
+For Tegra210 and Tegra186:
 - power-domains: A list of PM domain specifiers that reference each power-domain
   used by the xHCI controller. This list must comprise of a specifier for the
   XUSBA and XUSBC power-domains. See ../power/power_domain.txt and
@@ -78,6 +81,7 @@ Optional properties:
   - Tegra132: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1
   - Tegra210: usb2-0, usb2-1, usb2-2, usb2-3, hsic-0, usb3-0, usb3-1, usb3-2,
               usb3-3
+  - Tegra186: usb2-0, usb2-1, usb2-2, hsic-0, usb3-0, usb3-1, usb3-2
 
 Example:
 --------
Signature · 1 line
2.21.0
#2 lore raw

PATCH v2 2/6 usb: host: xhci-tegra: Selectively program IPFS

In reply to Thierry Reding

From: JC Kuo <[email protected]>

Starting with Tegra186, the XUSB controller no longer has the IPFS wrapper. This commit adds a "has_ipfs" field to struct tegra_xusb_soc that can be used to declare the existence of the IPFS wrapper.

For the existing chips (i.e. Tegra124 and Tegra210), the new field is set to true. A future patch adding support for Tegra186 will set it to false.

---
 drivers/usb/host/xhci-tegra.c | 43 +++++++++++++++++++++--------------
 1 file changed, 26 insertions(+), 17 deletions(-)
drivers/usb/host/xhci-tegra.c +26 -17
index efb0cad8710e..4d133bbabdda 100644
@@ -161,6 +161,7 @@ struct tegra_xusb_soc {
 	} ports;
 
 	bool scale_ss_clock;
+	bool has_ipfs;
 };
 
 struct tegra_xusb {
@@ -637,16 +638,18 @@ static irqreturn_t tegra_xusb_mbox_thread(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
-static void tegra_xusb_ipfs_config(struct tegra_xusb *tegra,
-				   struct resource *regs)
+static void tegra_xusb_config(struct tegra_xusb *tegra,
+			      struct resource *regs)
 {
 	u32 value;
 
-	value = ipfs_readl(tegra, IPFS_XUSB_HOST_CONFIGURATION_0);
-	value |= IPFS_EN_FPCI;
-	ipfs_writel(tegra, value, IPFS_XUSB_HOST_CONFIGURATION_0);
+	if (tegra->soc->has_ipfs) {
+		value = ipfs_readl(tegra, IPFS_XUSB_HOST_CONFIGURATION_0);
+		value |= IPFS_EN_FPCI;
+		ipfs_writel(tegra, value, IPFS_XUSB_HOST_CONFIGURATION_0);
 
-	usleep_range(10, 20);
+		usleep_range(10, 20);
+	}
 
 	/* Program BAR0 space */
 	value = fpci_readl(tegra, XUSB_CFG_4);
@@ -661,13 +664,15 @@ static void tegra_xusb_ipfs_config(struct tegra_xusb *tegra,
 	value |= XUSB_IO_SPACE_EN | XUSB_MEM_SPACE_EN | XUSB_BUS_MASTER_EN;
 	fpci_writel(tegra, value, XUSB_CFG_1);
 
-	/* Enable interrupt assertion */
-	value = ipfs_readl(tegra, IPFS_XUSB_HOST_INTR_MASK_0);
-	value |= IPFS_IP_INT_MASK;
-	ipfs_writel(tegra, value, IPFS_XUSB_HOST_INTR_MASK_0);
+	if (tegra->soc->has_ipfs) {
+		/* Enable interrupt assertion */
+		value = ipfs_readl(tegra, IPFS_XUSB_HOST_INTR_MASK_0);
+		value |= IPFS_IP_INT_MASK;
+		ipfs_writel(tegra, value, IPFS_XUSB_HOST_INTR_MASK_0);
 
-	/* Set hysteresis */
-	ipfs_writel(tegra, 0x80, IPFS_XUSB_HOST_CLKGATE_HYSTERESIS_0);
+		/* Set hysteresis */
+		ipfs_writel(tegra, 0x80, IPFS_XUSB_HOST_CLKGATE_HYSTERESIS_0);
+	}
 }
 
 static int tegra_xusb_clk_enable(struct tegra_xusb *tegra)
@@ -1015,10 +1020,12 @@ static int tegra_xusb_probe(struct platform_device *pdev)
 	if (IS_ERR(tegra->fpci_base))
 		return PTR_ERR(tegra->fpci_base);
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
-	tegra->ipfs_base = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(tegra->ipfs_base))
-		return PTR_ERR(tegra->ipfs_base);
+	if (tegra->soc->has_ipfs) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+		tegra->ipfs_base = devm_ioremap_resource(&pdev->dev, res);
+		if (IS_ERR(tegra->ipfs_base))
+			return PTR_ERR(tegra->ipfs_base);
+	}
 
 	tegra->xhci_irq = platform_get_irq(pdev, 0);
 	if (tegra->xhci_irq < 0)
@@ -1208,7 +1215,7 @@ static int tegra_xusb_probe(struct platform_device *pdev)
 		goto disable_rpm;
 	}
 
-	tegra_xusb_ipfs_config(tegra, regs);
+	tegra_xusb_config(tegra, regs);
 
 	err = tegra_xusb_load_firmware(tegra);
 	if (err < 0) {
@@ -1380,6 +1387,7 @@ static const struct tegra_xusb_soc tegra124_soc = {
 		.usb3 = { .offset = 0, .count = 2, },
 	},
 	.scale_ss_clock = true,
+	.has_ipfs = true,
 };
 MODULE_FIRMWARE("nvidia/tegra124/xusb.bin");
 
@@ -1411,6 +1419,7 @@ static const struct tegra_xusb_soc tegra210_soc = {
 		.usb3 = { .offset = 0, .count = 4, },
 	},
 	.scale_ss_clock = false,
+	.has_ipfs = true,
 };
 MODULE_FIRMWARE("nvidia/tegra210/xusb.bin");
 
Signature · 1 line
2.21.0
#3 lore raw

PATCH v2 3/6 usb: host: xhci-tegra: Add Tegra186 XUSB support

In reply to Thierry Reding

From: JC Kuo <[email protected]>

This commit adds Tegra186 XUSB host mode controller support. This is very similar to the existing support for Tegra124 and Tegra210, except that the number of ports and PHYs differs and the IPFS wrapper being gone.

---
 drivers/usb/host/xhci-tegra.c | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)
drivers/usb/host/xhci-tegra.c +25 -0
index 4d133bbabdda..294158113d62 100644
@@ -1423,9 +1423,34 @@ static const struct tegra_xusb_soc tegra210_soc = {
 };
 MODULE_FIRMWARE("nvidia/tegra210/xusb.bin");
 
+static const char * const tegra186_supply_names[] = {
+};
+
+static const struct tegra_xusb_phy_type tegra186_phy_types[] = {
+	{ .name = "usb3", .num = 3, },
+	{ .name = "usb2", .num = 3, },
+	{ .name = "hsic", .num = 1, },
+};
+
+static const struct tegra_xusb_soc tegra186_soc = {
+	.firmware = "nvidia/tegra186/xusb.bin",
+	.supply_names = tegra186_supply_names,
+	.num_supplies = ARRAY_SIZE(tegra186_supply_names),
+	.phy_types = tegra186_phy_types,
+	.num_types = ARRAY_SIZE(tegra186_phy_types),
+	.ports = {
+		.usb3 = { .offset = 0, .count = 3, },
+		.usb2 = { .offset = 3, .count = 3, },
+		.hsic = { .offset = 6, .count = 1, },
+	},
+	.scale_ss_clock = false,
+	.has_ipfs = false,
+};
+
 static const struct of_device_id tegra_xusb_of_match[] = {
 	{ .compatible = "nvidia,tegra124-xusb", .data = &tegra124_soc },
 	{ .compatible = "nvidia,tegra210-xusb", .data = &tegra210_soc },
+	{ .compatible = "nvidia,tegra186-xusb", .data = &tegra186_soc },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, tegra_xusb_of_match);
Signature · 1 line
2.21.0
#4 lore raw

PATCH v2 4/6 arm64: tegra: Add XUSB and pad controller on Tegra186

In reply to Thierry Reding

From: Thierry Reding <[email protected]>

Adds the XUSB pad and XUSB controllers on Tegra186.

---
 arch/arm64/boot/dts/nvidia/tegra186.dtsi | 135 +++++++++++++++++++++++
 1 file changed, 135 insertions(+)
arch/arm64/boot/dts/nvidia/tegra186.dtsi +135 -0
index 97aeb946ed5e..c444b6fa304c 100644
@@ -340,6 +340,141 @@
 		status = "disabled";
 	};
 
+	padctl: padctl@3520000 {
+		compatible = "nvidia,tegra186-xusb-padctl";
+		reg = <0x0 0x03520000 0x0 0x1000>,
+		      <0x0 0x03540000 0x0 0x1000>;
+		reg-names = "padctl", "ao";
+
+		resets = <&bpmp TEGRA186_RESET_XUSB_PADCTL>;
+		reset-names = "padctl";
+
+		status = "disabled";
+
+		pads {
+			usb2 {
+				clocks = <&bpmp TEGRA186_CLK_USB2_TRK>;
+				clock-names = "trk";
+				status = "disabled";
+
+				lanes {
+					usb2-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					usb2-1 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					usb2-2 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+
+			hsic {
+				clocks = <&bpmp TEGRA186_CLK_HSIC_TRK>;
+				clock-names = "trk";
+				status = "disabled";
+
+				lanes {
+					hsic-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+
+			usb3 {
+				status = "disabled";
+
+				lanes {
+					usb3-0 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					usb3-1 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+
+					usb3-2 {
+						status = "disabled";
+						#phy-cells = <0>;
+					};
+				};
+			};
+		};
+
+		ports {
+			usb2-0 {
+				status = "disabled";
+			};
+
+			usb2-1 {
+				status = "disabled";
+			};
+
+			usb2-2 {
+				status = "disabled";
+			};
+
+			hsic-0 {
+				status = "disabled";
+			};
+
+			usb3-0 {
+				status = "disabled";
+			};
+
+			usb3-1 {
+				status = "disabled";
+			};
+
+			usb3-2 {
+				status = "disabled";
+			};
+		};
+	};
+
+	usb@3530000 {
+		compatible = "nvidia,tegra186-xusb";
+		reg = <0x0 0x03530000 0x0 0x8000>,
+		      <0x0 0x03538000 0x0 0x1000>;
+		reg-names = "hcd", "fpci";
+
+		interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
+
+		clocks = <&bpmp TEGRA186_CLK_XUSB_HOST>,
+			 <&bpmp TEGRA186_CLK_XUSB_FALCON>,
+			 <&bpmp TEGRA186_CLK_XUSB_SS>,
+			 <&bpmp TEGRA186_CLK_XUSB_CORE_SS>,
+			 <&bpmp TEGRA186_CLK_CLK_M>,
+			 <&bpmp TEGRA186_CLK_XUSB_FS>,
+			 <&bpmp TEGRA186_CLK_PLLU>,
+			 <&bpmp TEGRA186_CLK_CLK_M>,
+			 <&bpmp TEGRA186_CLK_PLLE>;
+		clock-names = "xusb_host", "xusb_falcon_src", "xusb_ss",
+			      "xusb_ss_src", "xusb_hs_src", "xusb_fs_src",
+			      "pll_u_480m", "clk_m", "pll_e";
+
+		power-domains = <&bpmp TEGRA186_POWER_DOMAIN_XUSBC>,
+				<&bpmp TEGRA186_POWER_DOMAIN_XUSBA>;
+		power-domain-names = "xusb_host", "xusb_ss";
+		nvidia,xusb-padctl = <&padctl>;
+
+		status = "disabled";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
 	fuse@3820000 {
 		compatible = "nvidia,tegra186-efuse";
 		reg = <0x0 0x03820000 0x0 0x10000>;
Signature · 1 line
2.21.0
#5 lore raw

PATCH v2 5/6 arm64: tegra: Enable XUSB on P2771

In reply to Thierry Reding

From: Thierry Reding <[email protected]>

Enable the relevant pads for XUSB support on P2771-0000 and hook up the USB supply voltage regulators to the ports.

---
 .../boot/dts/nvidia/tegra186-p2771-0000.dts   | 115 ++++++++++++++++++
 .../arm64/boot/dts/nvidia/tegra186-p3310.dtsi |  19 ++-
 2 files changed, 130 insertions(+), 4 deletions(-)
arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts +115 -0
index 31457f32e4d0..75ee6cf1e1b4 100644
@@ -58,6 +58,93 @@
 		status = "okay";
 	};
 
+	padctl@3520000 {
+		status = "okay";
+
+		avdd-pll-erefeut-supply = <&vdd_1v8_pll>;
+		avdd-usb-supply = <&vdd_3v3_sys>;
+		dvdd-pex-supply = <&vdd_pex>;
+		dvdd-pex-pll-supply = <&vdd_pex>;
+		hvdd-pex-supply = <&vdd_1v8>;
+		hvdd-pex-pll-supply = <&vdd_1v8>;
+		vclamp-usb-supply = <&vdd_1v8>;
+		vddio-hsic-supply = <&gnd>;
+
+		pads {
+			usb2 {
+				status = "okay";
+
+				lanes {
+					usb2-0 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+
+					usb2-1 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+
+					usb2-2 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+				};
+			};
+
+			usb3 {
+				status = "okay";
+
+				lanes {
+					usb3-0 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+
+					usb3-1 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+
+					usb3-2 {
+						nvidia,function = "xusb";
+						status = "okay";
+					};
+				};
+			};
+		};
+
+		ports {
+			usb2-0 {
+				status = "okay";
+				mode = "otg";
+
+				vbus-supply = <&vdd_usb0>;
+			};
+
+			usb2-1 {
+				status = "okay";
+				mode = "host";
+
+				vbus-supply = <&vdd_usb1>;
+			};
+
+			usb3-0 {
+				nvidia,usb2-companion = <1>;
+				status = "okay";
+			};
+		};
+	};
+
+	usb@3530000 {
+		status = "okay";
+
+		phys = <&{/padctl@3520000/pads/usb2/lanes/usb2-0}>,
+		       <&{/padctl@3520000/pads/usb2/lanes/usb2-1}>,
+		       <&{/padctl@3520000/pads/usb3/lanes/usb3-0}>;
+		phy-names = "usb2-0", "usb2-1", "usb3-0";
+	};
+
 	pcie@10003000 {
 		status = "okay";
 
@@ -182,5 +269,33 @@
 
 			vin-supply = <&vdd_5v0_sys>;
 		};
+
+		vdd_usb0: regulator@102 {
+			compatible = "regulator-fixed";
+			reg = <102>;
+
+			regulator-name = "VDD_USB0";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+
+			gpio = <&gpio TEGRA_MAIN_GPIO(L, 4) GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+
+			vin-supply = <&vdd_5v0_sys>;
+		};
+
+		vdd_usb1: regulator@103 {
+			compatible = "regulator-fixed";
+			reg = <103>;
+
+			regulator-name = "VDD_USB1";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+
+			gpio = <&gpio TEGRA_MAIN_GPIO(L, 5) GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+
+			vin-supply = <&vdd_5v0_sys>;
+		};
 	};
 };
arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi +15 -4
index 89a2da46efae..952062f0b9a9 100644
@@ -291,7 +291,7 @@
 						regulator-boot-on;
 					};
 
-					ldo0 {
+					vdd_1v8_pll: ldo0 {
 						regulator-name = "VDD_1V8_AP_PLL";
 						regulator-min-microvolt = <1800000>;
 						regulator-max-microvolt = <1800000>;
@@ -360,10 +360,21 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		vdd_5v0_sys: regulator@0 {
+		gnd: regulator@0 {
 			compatible = "regulator-fixed";
 			reg = <0>;
 
+			regulator-name = "GND";
+			regulator-min-microvolt = <0>;
+			regulator-max-microvolt = <0>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		vdd_5v0_sys: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+
 			regulator-name = "VDD_5V0_SYS";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
@@ -371,9 +382,9 @@
 			regulator-boot-on;
 		};
 
-		vdd_1v8_ap: regulator@1 {
+		vdd_1v8_ap: regulator@2 {
 			compatible = "regulator-fixed";
-			reg = <1>;
+			reg = <2>;
 
 			regulator-name = "VDD_1V8_AP";
 			regulator-min-microvolt = <1800000>;
Signature · 1 line
2.21.0
#6 lore raw

PATCH v2 6/6 arm64: tegra: Remove regulator hacks on Jetson TX2

In reply to Thierry Reding

From: Thierry Reding <[email protected]>

Various regulators were marked as always-on for Jetson TX2. At this point, all of the regulators are properly hooked up, so this workaround is no longer required.

---
 .../arm64/boot/dts/nvidia/tegra186-p3310.dtsi | 23 -------------------
 1 file changed, 23 deletions(-)
arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi +0 -23
index 952062f0b9a9..64686b033c38 100644
@@ -268,43 +268,30 @@
 						regulator-name = "AVDD_DSI_CSI_1V2";
 						regulator-min-microvolt = <1200000>;
 						regulator-max-microvolt = <1200000>;
-						/* XXX */
-						regulator-always-on;
-						regulator-boot-on;
 					};
 
 					vdd_1v8: sd2 {
 						regulator-name = "VDD_1V8";
 						regulator-min-microvolt = <1800000>;
 						regulator-max-microvolt = <1800000>;
-						/* XXX */
-						regulator-always-on;
-						regulator-boot-on;
 					};
 
 					vdd_3v3_sys: sd3 {
 						regulator-name = "VDD_3V3_SYS";
 						regulator-min-microvolt = <3300000>;
 						regulator-max-microvolt = <3300000>;
-						/* XXX */
-						regulator-always-on;
-						regulator-boot-on;
 					};
 
 					vdd_1v8_pll: ldo0 {
 						regulator-name = "VDD_1V8_AP_PLL";
 						regulator-min-microvolt = <1800000>;
 						regulator-max-microvolt = <1800000>;
-						/* XXX */
-						regulator-always-on;
-						regulator-boot-on;
 					};
 
 					ldo2 {
 						regulator-name = "VDDIO_3V3_AOHV";
 						regulator-min-microvolt = <3300000>;
 						regulator-max-microvolt = <3300000>;
-						/* XXX */
 						regulator-always-on;
 						regulator-boot-on;
 					};
@@ -331,18 +318,12 @@
 						regulator-name = "VDD_HDMI_1V05";
 						regulator-min-microvolt = <1050000>;
 						regulator-max-microvolt = <1050000>;
-						/* XXX */
-						regulator-always-on;
-						regulator-boot-on;
 					};
 
 					vdd_pex: ldo8 {
 						regulator-name = "VDD_PEX_1V05";
 						regulator-min-microvolt = <1050000>;
 						regulator-max-microvolt = <1050000>;
-						/* XXX */
-						regulator-always-on;
-						regulator-boot-on;
 					};
 				};
 			};
@@ -390,10 +371,6 @@
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 
-			/* XXX */
-			regulator-always-on;
-			regulator-boot-on;
-
 			gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
 			enable-active-high;
 
Signature · 1 line
2.21.0
#7 lore raw
In reply to Thierry Reding
Quoted 13 lines · Thierry Reding

From: Thierry Reding <[email protected]>

Hi,

This series introduces support for XUSB to the Tegra186 SoC. This is mostly the same as on earlier generations in that it provides an XHCI compatible interface with a bit of vendor-specific glue. Perhaps the most notable change is the removal of the IPFS wrapper. Patches for the UPHY related changes that control the PHYs for the XUSB controller were merged into v5.1.

This version is a rebase of the series posted here:

Quoted 7 lines
    http://patchwork.ozlabs.org/project/linux-tegra/list/?series=88193

There have been no code changes and I collected Reviewed-by and Acked-by tags.

Greg, can you pick up patches 1-3 with Rob's and Mathias' Acked-by, respectively? I'll pick up patches 4-6 into the Tegra tree.

Hi Greg,

would you mind picking up patches 1-3 of this series?

Thanks,
Thierry

#8 lore raw
Quoted 19 lines · Thierry Reding
Quoted 18 lines · Thierry Reding

From: Thierry Reding <[email protected]>

Hi,

This series introduces support for XUSB to the Tegra186 SoC. This is mostly the same as on earlier generations in that it provides an XHCI compatible interface with a bit of vendor-specific glue. Perhaps the most notable change is the removal of the IPFS wrapper. Patches for the UPHY related changes that control the PHYs for the XUSB controller were merged into v5.1.

This version is a rebase of the series posted here:

    http://patchwork.ozlabs.org/project/linux-tegra/list/?series=88193

There have been no code changes and I collected Reviewed-by and Acked-by tags.

Quoted 6 lines
Quoted 2 lines

Greg, can you pick up patches 1-3 with Rob's and Mathias' Acked-by, respectively? I'll pick up patches 4-6 into the Tegra tree.

Hi Greg,

would you mind picking up patches 1-3 of this series?

FYI: Greg is on vacation for the coming week, with no email access.

Alan Stern

#9 lore raw
Quoted 21 lines · Alan Stern
Quoted 19 lines · Thierry Reding
Quoted 18 lines · Thierry Reding

From: Thierry Reding <[email protected]>

Hi,

This series introduces support for XUSB to the Tegra186 SoC. This is mostly the same as on earlier generations in that it provides an XHCI compatible interface with a bit of vendor-specific glue. Perhaps the most notable change is the removal of the IPFS wrapper. Patches for the UPHY related changes that control the PHYs for the XUSB controller were merged into v5.1.

This version is a rebase of the series posted here:

    http://patchwork.ozlabs.org/project/linux-tegra/list/?series=88193

There have been no code changes and I collected Reviewed-by and Acked-by tags.

Quoted 8 lines
Quoted 6 lines
Quoted 2 lines

Greg, can you pick up patches 1-3 with Rob's and Mathias' Acked-by, respectively? I'll pick up patches 4-6 into the Tegra tree.

Hi Greg,

would you mind picking up patches 1-3 of this series?

FYI: Greg is on vacation for the coming week, with no email access.

Thanks for letting me know, Alan. I'll ping Greg again when he's back.

Thierry