board: sun50i: h6: Add Beelink GS1 initial support
Subsystems (2)
PATCH 1/1 board: sun50i: h6: Add Beelink GS1 initial support
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 Host, OTG
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
---
This is based on Jagan Teki works for the OrangePi One Plus.
This board is closed source and some regulators may be wrong.
The sys_config.fex is available here: https://pastebin.com/TdnfRMJL
U-Boot bootlog is available here: https://pastebin.com/FXAU1app
Regards,
Clement
arch/arm/dts/Makefile | 1 + arch/arm/dts/sun50i-h6-beelink-gs1.dts | 152 +++++++++++++++++++++++++ configs/beelink_gs1_defconfig | 12 ++ 3 files changed, 165 insertions(+) create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts create mode 100644 configs/beelink_gs1_defconfig
arch/arm/dts/Makefile +1 -0
@@ -467,6 +467,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \ sun50i-h5-orangepi-prime.dtb \ sun50i-h5-orangepi-zero-plus2.dtb dtb-$(CONFIG_MACH_SUN50I_H6) += \ + sun50i-h6-beelink-gs1.dtb \ sun50i-h6-orangepi-lite2.dtb \ sun50i-h6-orangepi-one-plus.dtb \ sun50i-h6-pine-h64.dtb
arch/arm/dts/sun50i-h6-beelink-gs1.dts new file +152 -0
152 lines not on this page · raw message
configs/beelink_gs1_defconfig new file +12 -0
@@ -0,0 +1,12 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_SPL=y +CONFIG_MACH_SUN50I_H6=y +CONFIG_MMC0_CD_PIN="PF6" +# CONFIG_PSCI_RESET is not set +CONFIG_NR_DRAM_BANKS=1 +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_SPL_DOS_PARTITION is not set +# CONFIG_SPL_EFI_PARTITION is not set +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-beelink-gs1"
Signature · 1 line
2.17.1
PATCH 1/1 board: sun50i: h6: Add Beelink GS1 initial support
Hi,
Please Ignore this patch I will resend a new serie.
Thanks,
Clement
Quoted 227 lines · Clément Péron
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 Host, OTG
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)Signed-off-by Clément Péron <[email protected]>---
This is based on Jagan Teki works for the OrangePi One Plus.
This board is closed source and some regulators may be wrong.
The sys_config.fex is available here: https://pastebin.com/TdnfRMJL
U-Boot bootlog is available here: https://pastebin.com/FXAU1app
Regards,
Clementarch/arm/dts/Makefile | 1 + arch/arm/dts/sun50i-h6-beelink-gs1.dts | 152 +++++++++++++++++++++++++ configs/beelink_gs1_defconfig | 12 ++ 3 files changed, 165 insertions(+) create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts create mode 100644 configs/beelink_gs1_defconfigarch/arm/dts/Makefile +1
-0@@ -467,6 +467,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \ sun50i-h5-orangepi-prime.dtb \ sun50i-h5-orangepi-zero-plus2.dtb dtb-$(CONFIG_MACH_SUN50I_H6) += \ + sun50i-h6-beelink-gs1.dtb \ sun50i-h6-orangepi-lite2.dtb \ sun50i-h6-orangepi-one-plus.dtb \ sun50i-h6-pine-h64.dtbarch/arm/dts/sun50i-h6-beelink-gs1.dts new file +152
-0@@ -0,0 +1,152 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2019 Clément Péron <[email protected]> + * Based on: sun50i-h6-orangepi.dtsi + * - Copyright (C) 2018 Amarula Solutions + * Author: Jagan Teki <[email protected]> + */ + +/dts-v1/; + +#include "sun50i-h6.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Beelink GS1"; + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_cldo1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + bus-width = <4>; + status = "okay"; +}; + +&r_i2c { + status = "okay"; + + axp805: pmic at 36 { + compatible = "x-powers,axp805", "x-powers,axp806"; + reg = <0x36>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + x-powers,self-working-mode; + + regulators { + reg_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pl"; + }; + + reg_aldo2: aldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-ac200"; + }; + + reg_aldo3: aldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc25-dram"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-bias-pll"; + }; + + reg_bldo2: bldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-efuse-pcie-hdmi-io"; + }; + + reg_bldo3: bldo3 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-dcxoio"; + }; + + bldo4 { + /* unused */ + }; + + reg_cldo1: cldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; + }; + + reg_cldo2: cldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-1"; + }; + + reg_cldo3: cldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-2"; + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdcc: dcdcc { + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-gpu"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <960000>; + regulator-max-microvolt = <960000>; + regulator-name = "vdd-sys"; + }; + + reg_dcdce: dcdce { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; + }; + + sw { + /* unused */ + }; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +};configs/beelink_gs1_defconfig new file +12
-1@@ -0,0 +1,12 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_SPL=y +CONFIG_MACH_SUN50I_H6=y +CONFIG_MMC0_CD_PIN="PF6" +# CONFIG_PSCI_RESET is not set +CONFIG_NR_DRAM_BANKS=1 +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_SPL_DOS_PARTITION is not set +# CONFIG_SPL_EFI_PARTITION is not set +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-beelink-gs1" --2.17.1