Skip to contentSkip to conversation

tty/serial: atmel: Add is_half_duplex helper

PATCH Applied Razvan Stefanescu 2 participants 5 messages Apr 2, 2019 – Apr 3, 2019

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 tty/serial: atmel: Add is_half_duplex helper

commit f3040983132b ("tty/serial: atmel: Add is_half_duplex helper") upstream.

Use a helper function to check that a port needs to use half duplex communication, replacing several occurrences of multi-line bit checking.

Fixes b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done")
Cc stable <[email protected]>
---
 drivers/tty/serial/atmel_serial.c | 19 +++++++++++--------
 1 file changed, 11 insertions(+), 8 deletions(-)
drivers/tty/serial/atmel_serial.c +11 -8
index 8e4428725848..6b38eed7b3d0 100644
@@ -225,6 +225,12 @@ static inline void atmel_uart_write_char(struct uart_port *port, u8 value)
 	__raw_writeb(value, port->membase + ATMEL_US_THR);
 }
 
+static inline int atmel_uart_is_half_duplex(struct uart_port *port)
+{
+	return (port->rs485.flags & SER_RS485_ENABLED) &&
+		!(port->rs485.flags & SER_RS485_RX_DURING_TX);
+}
+
 #ifdef CONFIG_SERIAL_ATMEL_PDC
 static bool atmel_use_pdc_rx(struct uart_port *port)
 {
@@ -481,9 +487,9 @@ static void atmel_stop_tx(struct uart_port *port)
 	/* Disable interrupts */
 	atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
 
-	if ((port->rs485.flags & SER_RS485_ENABLED) &&
-	    !(port->rs485.flags & SER_RS485_RX_DURING_TX))
+	if (atmel_uart_is_half_duplex(port))
 		atmel_start_rx(port);
+
 }
 
 /*
@@ -500,8 +506,7 @@ static void atmel_start_tx(struct uart_port *port)
 		return;
 
 	if (atmel_use_pdc_tx(port) || atmel_use_dma_tx(port))
-		if ((port->rs485.flags & SER_RS485_ENABLED) &&
-		    !(port->rs485.flags & SER_RS485_RX_DURING_TX))
+		if (atmel_uart_is_half_duplex(port))
 			atmel_stop_rx(port);
 
 	if (atmel_use_pdc_tx(port))
@@ -799,8 +804,7 @@ static void atmel_complete_tx_dma(void *arg)
 	 */
 	if (!uart_circ_empty(xmit))
 		atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
-	else if ((port->rs485.flags & SER_RS485_ENABLED) &&
-		 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
+	else if (atmel_uart_is_half_duplex(port)) {
 		/* DMA done, stop TX, start RX for RS485 */
 		atmel_start_rx(port);
 	}
@@ -1373,8 +1377,7 @@ static void atmel_tx_pdc(struct uart_port *port)
 		atmel_uart_writel(port, ATMEL_US_IER,
 				  atmel_port->tx_done_mask);
 	} else {
-		if ((port->rs485.flags & SER_RS485_ENABLED) &&
-		    !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
+		if (atmel_uart_is_half_duplex(port)) {
 			/* DMA done, stop TX, start RX for RS485 */
 			atmel_start_rx(port);
 		}
Signature · 1 line
2.19.1
#1 lore raw

PATCH 2/2 tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped

commit 69646d7a3689 ("tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped") upstream.

In half-duplex operation, RX should be started after TX completes.

If DMA is used, there is a case when the DMA transfer completes but the TX FIFO is not emptied, so the RX cannot be restarted just yet.

Use a boolean variable to store this state and rearm TX interrupt mask to be signaled again that the transfer finished. In interrupt transmit handler this variable is used to start RX. A warning message is generated if RX is activated before TX fifo is cleared.

Fixes b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable

RX after TX is done")

---
 drivers/tty/serial/atmel_serial.c | 24 +++++++++++++++++++++---
 1 file changed, 21 insertions(+), 3 deletions(-)
drivers/tty/serial/atmel_serial.c +21 -3
index 6b38eed7b3d0..7c49c7ce2449 100644
@@ -163,6 +163,8 @@ struct atmel_uart_port {
 	unsigned int		pending_status;
 	spinlock_t		lock_suspended;
 
+	bool			hd_start_rx;	/* can start RX during half-duplex operation */
+
 #ifdef CONFIG_PM
 	struct {
 		u32		cr;
@@ -805,8 +807,13 @@ static void atmel_complete_tx_dma(void *arg)
 	if (!uart_circ_empty(xmit))
 		atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
 	else if (atmel_uart_is_half_duplex(port)) {
-		/* DMA done, stop TX, start RX for RS485 */
-		atmel_start_rx(port);
+		/*
+		 * DMA done, re-enable TXEMPTY and signal that we can stop
+		 * TX and start RX for RS485
+		 */
+		atmel_port->hd_start_rx = true;
+		atmel_uart_writel(port, ATMEL_US_IER,
+				  atmel_port->tx_done_mask);
 	}
 
 	spin_unlock_irqrestore(&port->lock, flags);
@@ -1248,9 +1255,20 @@ atmel_handle_transmit(struct uart_port *port, unsigned int pending)
 	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
 
 	if (pending & atmel_port->tx_done_mask) {
-		/* Either PDC or interrupt transmission */
 		atmel_uart_writel(port, ATMEL_US_IDR,
 				  atmel_port->tx_done_mask);
+
+		/* Start RX if flag was set and FIFO is empty */
+		if (atmel_port->hd_start_rx) {
+			if (!(atmel_uart_readl(port, ATMEL_US_CSR)
+					& ATMEL_US_TXEMPTY))
+				dev_warn(port->dev, "Should start RX, but TX fifo is not empty\n");
+
+			atmel_port->hd_start_rx = false;
+			atmel_start_rx(port);
+			return;
+		}
+
 		atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
 	}
 }
Signature · 1 line
2.19.1
maintainer Applied
#2 lore raw

Re: [PATCH for-4.19 2/2] tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped

Quoted 13 lines · Razvan Stefanescu

commit 69646d7a3689 ("tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped") upstream.

In half-duplex operation, RX should be started after TX completes.

If DMA is used, there is a case when the DMA transfer completes but the TX FIFO is not emptied, so the RX cannot be restarted just yet.

Use a boolean variable to store this state and rearm TX interrupt mask to be signaled again that the transfer finished. In interrupt transmit handler this variable is used to start RX. A warning message is generated if RX is activated before TX fifo is cleared.

Fixes b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable
Quoted 9 lines

RX after TX is done")

---
 drivers/tty/serial/atmel_serial.c | 24 +++++++++++++++++++++---
 1 file changed, 21 insertions(+), 3 deletions(-)

Happen to have a version of this for 4.4.y and 4.9.y?

I've queued both of these patches up now, thanks.

greg k-h

#3 lore raw

Re: [PATCH for-4.19 2/2] tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped

Quoted 24 lines · Greg Kroah-Hartman
Quoted 13 lines · Razvan Stefanescu

commit 69646d7a3689 ("tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped") upstream.

In half-duplex operation, RX should be started after TX completes.

If DMA is used, there is a case when the DMA transfer completes but the TX FIFO is not emptied, so the RX cannot be restarted just yet.

Use a boolean variable to store this state and rearm TX interrupt mask to be signaled again that the transfer finished. In interrupt transmit handler this variable is used to start RX. A warning message is generated if RX is activated before TX fifo is cleared.

Fixes b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable
Quoted 9 lines

RX after TX is done")

---
  drivers/tty/serial/atmel_serial.c | 24 +++++++++++++++++++++---
  1 file changed, 21 insertions(+), 3 deletions(-)
Quoted 4 lines

Happen to have a version of this for 4.4.y and 4.9.y?

I've queued both of these patches up now, thanks.

Thank you for picking them. I've sent the patches for 4.4.y and 4.9.y.

Best regards,
Razvan Stefanescu

maintainer
#4 lore raw

Re: [PATCH for-4.19 2/2] tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped

Quoted 27 lines · On Wed, Apr 03, 2019 at 03:07:18PM +0000, [email protected] wrote:
Quoted 24 lines · Greg Kroah-Hartman
Quoted 22 lines · Razvan Stefanescu

commit 69646d7a3689 ("tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped") upstream.

In half-duplex operation, RX should be started after TX completes.

If DMA is used, there is a case when the DMA transfer completes but the TX FIFO is not emptied, so the RX cannot be restarted just yet.

Use a boolean variable to store this state and rearm TX interrupt mask to be signaled again that the transfer finished. In interrupt transmit handler this variable is used to start RX. A warning message is generated if RX is activated before TX fifo is cleared.

Fixes b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable

RX after TX is done")

---
  drivers/tty/serial/atmel_serial.c | 24 +++++++++++++++++++++---
  1 file changed, 21 insertions(+), 3 deletions(-)
Quoted 6 lines
Quoted 4 lines

Happen to have a version of this for 4.4.y and 4.9.y?

I've queued both of these patches up now, thanks.

Thank you for picking them. I've sent the patches for 4.4.y and 4.9.y.

Thanks for those, now queued up.

greg k-h