Skip to contentSkip to conversation

ARM: dts: imx: Fix the AR803X phy-mode

PATCH Superseded Fabio Estevam 3 participants 5 messages Apr 2, 2019 – Apr 3, 2019

Subsystems (3)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Fabio Estevam

author reviewer
#0 lore raw

PATCH v2 1/1 ARM: dts: imx: Fix the AR803X phy-mode

Commit 6d4cd041f0af ("net: phy: at803x: disable delay only for RGMII mode") exposed an issue on imx DTS files using AR8031/AR8035 PHYs.

The end result is that the boards can no longer obtain an IP address via UDHCP, for example.

Quoting Andrew Lunn:

"The problem here is, all the DTs were broken since day 0. However, because the PHY driver was also broken, nobody noticed and it worked. Now that the PHY driver has been fixed, all the bugs in the DTs now become an issue"

To fix this problem, the phy-mode property needs to be "rgmii-id", which has the following meaning as per Documentation/devicetree/bindings/net/ethernet.txt:

"RGMII with internal RX and TX delays provided by the PHY, the MAC should not add the RX or TX delays in this case)"

Tested on imx6-sabresd, imx6sx-sdb and imx7d-pico boards with successfully restored networking.

Based on the initial submission from Steve Twiss for the imx6qdl-sabresd.

---
Changes since v1:
- Also fix imx6-logicpd and imx6q-marsboard

 arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi | 2 +-
 arch/arm/boot/dts/imx6dl-riotboard.dts        | 2 +-
 arch/arm/boot/dts/imx6q-marsboard.dts         | 2 +-
 arch/arm/boot/dts/imx6q-tbs2910.dts           | 2 +-
 arch/arm/boot/dts/imx6qdl-apf6.dtsi           | 2 +-
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi      | 2 +-
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi        | 2 +-
 arch/arm/boot/dts/imx6qdl-sr-som.dtsi         | 2 +-
 arch/arm/boot/dts/imx6qdl-wandboard.dtsi      | 2 +-
 arch/arm/boot/dts/imx6sx-sabreauto.dts        | 2 +-
 arch/arm/boot/dts/imx6sx-sdb.dtsi             | 2 +-
 arch/arm/boot/dts/imx7d-pico.dtsi             | 2 +-
 12 files changed, 12 insertions(+), 12 deletions(-)
arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi +1 -1
index fb01fa6e4224..3cae139e6396 100644
@@ -216,7 +216,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-duration = <10>;
 	phy-reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 	phy-supply = <&reg_enet>;
arch/arm/boot/dts/imx6dl-riotboard.dts +1 -1
index 65c184bb8fb0..d9de49efa802 100644
@@ -92,7 +92,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
arch/arm/boot/dts/imx6q-marsboard.dts +1 -1
index d8ccb533b6b7..84b30bd6908f 100644
@@ -110,7 +110,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
arch/arm/boot/dts/imx6q-tbs2910.dts +1 -1
index 2ce8399a10ba..bfff87ce2e1f 100644
@@ -98,7 +98,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
arch/arm/boot/dts/imx6qdl-apf6.dtsi +1 -1
index 1ebf29f43a24..4738c3c1ab50 100644
@@ -51,7 +51,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-duration = <10>;
 	phy-reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 	status = "okay";
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +1 -1
index 1280de50a984..f3404dd10537 100644
@@ -292,7 +292,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
arch/arm/boot/dts/imx6qdl-sabresd.dtsi +1 -1
index a0705066ccba..185fb17a3500 100644
@@ -202,7 +202,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
arch/arm/boot/dts/imx6qdl-sr-som.dtsi +1 -1
index 4ccb7afc4b35..6d7f6b9035bc 100644
@@ -53,7 +53,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-duration = <2>;
 	phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
 	status = "okay";
arch/arm/boot/dts/imx6qdl-wandboard.dtsi +1 -1
index b7d5fb421404..50d9a989e06a 100644
@@ -224,7 +224,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
arch/arm/boot/dts/imx6sx-sabreauto.dts +1 -1
index b0ee324afe58..315044ccd65f 100644
@@ -75,7 +75,7 @@
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy1>;
 	fsl,magic-packet;
 	status = "okay";
arch/arm/boot/dts/imx6sx-sdb.dtsi +1 -1
index 08ede56c3f10..f6972deb5e39 100644
@@ -191,7 +191,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1>;
 	phy-supply = <&reg_enet_3v3>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy1>;
 	phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
 	status = "okay";
arch/arm/boot/dts/imx7d-pico.dtsi +1 -1
index 3fd595a71202..6f50ebf31a0a 100644
@@ -92,7 +92,7 @@
 			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
 	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
 	assigned-clock-rates = <0>, <100000000>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy0>;
 	fsl,magic-packet;
 	phy-reset-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
Signature · 1 line
2.17.1
Tested-by on v2 1/1
#1 lore raw
Quoted 27 lines · Fabio Estevam

Commit 6d4cd041f0af ("net: phy: at803x: disable delay only for RGMII mode") exposed an issue on imx DTS files using AR8031/AR8035 PHYs.

The end result is that the boards can no longer obtain an IP address via UDHCP, for example.

Quoting Andrew Lunn:

"The problem here is, all the DTs were broken since day 0. However, because the PHY driver was also broken, nobody noticed and it worked. Now that the PHY driver has been fixed, all the bugs in the DTs now become an issue"

To fix this problem, the phy-mode property needs to be "rgmii-id", which has the following meaning as per Documentation/devicetree/bindings/net/ethernet.txt:

"RGMII with internal RX and TX delays provided by the PHY, the MAC should not add the RX or TX delays in this case)"

Tested on imx6-sabresd, imx6sx-sdb and imx7d-pico boards with successfully restored networking.

Based on the initial submission from Steve Twiss for the imx6qdl-sabresd.

Quoted 9 lines
Quoted 5 lines

---
Changes since v1:
- Also fix imx6-logicpd and imx6q-marsboard

 arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi | 2 +-

Thanks for doing that.

adam

Quoted 172 lines
 arch/arm/boot/dts/imx6dl-riotboard.dts        | 2 +-
 arch/arm/boot/dts/imx6q-marsboard.dts         | 2 +-
 arch/arm/boot/dts/imx6q-tbs2910.dts           | 2 +-
 arch/arm/boot/dts/imx6qdl-apf6.dtsi           | 2 +-
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi      | 2 +-
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi        | 2 +-
 arch/arm/boot/dts/imx6qdl-sr-som.dtsi         | 2 +-
 arch/arm/boot/dts/imx6qdl-wandboard.dtsi      | 2 +-
 arch/arm/boot/dts/imx6sx-sabreauto.dts        | 2 +-
 arch/arm/boot/dts/imx6sx-sdb.dtsi             | 2 +-
 arch/arm/boot/dts/imx7d-pico.dtsi             | 2 +-
 12 files changed, 12 insertions(+), 12 deletions(-)
arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi +1 -1
index fb01fa6e4224..3cae139e6396 100644
@@ -216,7 +216,7 @@
 &fec {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_enet>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        phy-reset-duration = <10>;
        phy-reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
        phy-supply = <&reg_enet>;
arch/arm/boot/dts/imx6dl-riotboard.dts +1 -1
index 65c184bb8fb0..d9de49efa802 100644
@@ -92,7 +92,7 @@
 &fec {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_enet>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        phy-reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
        interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
                              <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
arch/arm/boot/dts/imx6q-marsboard.dts +1 -1
index d8ccb533b6b7..84b30bd6908f 100644
@@ -110,7 +110,7 @@
 &fec {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_enet>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        phy-reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
        status = "okay";
 };
arch/arm/boot/dts/imx6q-tbs2910.dts +1 -1
index 2ce8399a10ba..bfff87ce2e1f 100644
@@ -98,7 +98,7 @@
 &fec {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_enet>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
        status = "okay";
 };
arch/arm/boot/dts/imx6qdl-apf6.dtsi +1 -1
index 1ebf29f43a24..4738c3c1ab50 100644
@@ -51,7 +51,7 @@
 &fec {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_enet>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        phy-reset-duration = <10>;
        phy-reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
        status = "okay";
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +1 -1
index 1280de50a984..f3404dd10537 100644
@@ -292,7 +292,7 @@
 &fec {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_enet>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
                              <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
        fsl,err006687-workaround-present;
arch/arm/boot/dts/imx6qdl-sabresd.dtsi +1 -1
index a0705066ccba..185fb17a3500 100644
@@ -202,7 +202,7 @@
 &fec {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_enet>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
        status = "okay";
 };
arch/arm/boot/dts/imx6qdl-sr-som.dtsi +1 -1
index 4ccb7afc4b35..6d7f6b9035bc 100644
@@ -53,7 +53,7 @@
 &fec {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        phy-reset-duration = <2>;
        phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
        status = "okay";
arch/arm/boot/dts/imx6qdl-wandboard.dtsi +1 -1
index b7d5fb421404..50d9a989e06a 100644
@@ -224,7 +224,7 @@
 &fec {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_enet>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
        interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
                              <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
arch/arm/boot/dts/imx6sx-sabreauto.dts +1 -1
index b0ee324afe58..315044ccd65f 100644
@@ -75,7 +75,7 @@
 &fec1 {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_enet1>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        phy-handle = <&ethphy1>;
        fsl,magic-packet;
        status = "okay";
arch/arm/boot/dts/imx6sx-sdb.dtsi +1 -1
index 08ede56c3f10..f6972deb5e39 100644
@@ -191,7 +191,7 @@
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_enet1>;
        phy-supply = <&reg_enet_3v3>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        phy-handle = <&ethphy1>;
        phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
        status = "okay";
arch/arm/boot/dts/imx7d-pico.dtsi +1 -2
index 3fd595a71202..6f50ebf31a0a 100644
@@ -92,7 +92,7 @@
                          <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
        assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
        assigned-clock-rates = <0>, <100000000>;
-       phy-mode = "rgmii";
+       phy-mode = "rgmii-id";
        phy-handle = <&ethphy0>;
        fsl,magic-packet;
        phy-reset-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
--

2.17.1

maintainer
#2 lore raw
In reply to Fabio Estevam

Hi,

[This is an automated email]

This commit has been processed because it contains a -stable tag. The stable tag indicates that it's relevant for the following trees: 4.9+

The bot has tested the following trees: v5.0.5, v4.19.32, v4.14.109, v4.9.166.

v5.0.5: Failed to apply! Possible dependencies:
1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM")

v4.19.32: Failed to apply! Possible dependencies:
1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM") 29988e867cb1 ("ARM: dts: imx7: Fix memory node duplication") 4edbe6aa46d1 ("ARM: dts: imx7d-pico-pi: Move SoM related part to imx7d-pico.dtsi") 50536c661194 ("ARM: dts: imx7d-pico: Do not harcode the memory size")

v4.14.109: Failed to apply! Possible dependencies:
1bf52b98ae1c ("ARM: dts: imx6sx-sabreauto: add external 24MHz clock source") 1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM") 221aaa198e70 ("ARM: dts: imx6sx-sabreauto: drop board specific pinctrl container node") 37accf72e04b ("ARM: dts: imx6sx-sabreauto: add fec support") 41bbeadceb03 ("ARM: dts: imx7d-pico-pi: Separate into cpu and baseboard dts") 4edbe6aa46d1 ("ARM: dts: imx7d-pico-pi: Move SoM related part to imx7d-pico.dtsi") 76dc340e7585 ("ARM: dts: imx6qdl: SolidRun: move AR8035 into microsom") 8dccafaa281a ("arm: dts: fix unit-address leading 0s")
99a52450c707 ("ARM: dts: imx7d-pico: Add Wifi support")
d9e246cc2880 ("ARM: dts: imx6sx-sabreauto: add PMIC support")

v4.9.166: Failed to apply! Possible dependencies:
12de44f55dcd ("ARM: dts: imx: Fix Ethernet PHY reset polarity") 1317efa1699f ("ARM: dts: imx6ul: Add DTS for liteSOM module") 13283626c889 ("ARM: dts: imx/vf: Correct license text")
1bf52b98ae1c ("ARM: dts: imx6sx-sabreauto: add external 24MHz clock source") 1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM") 221aaa198e70 ("ARM: dts: imx6sx-sabreauto: drop board specific pinctrl container node") 23c787a99ff7 ("ARM: dts: imx7d-pico: Add initial support")
26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia")
37accf72e04b ("ARM: dts: imx6sx-sabreauto: add fec support")
3faa1bb2e89c ("ARM: dts: imx: add Boundary Devices Nitrogen6_SOM2 support") 41bbeadceb03 ("ARM: dts: imx7d-pico-pi: Separate into cpu and baseboard dts") 478c9440b328 ("ARM: dts: imx6ul: Add DTS for liteBoard")
4edbe6aa46d1 ("ARM: dts: imx7d-pico-pi: Move SoM related part to imx7d-pico.dtsi") 6df11287f7c9 ("ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual initial support") 76dc340e7585 ("ARM: dts: imx6qdl: SolidRun: move AR8035 into microsom") 8dccafaa281a ("arm: dts: fix unit-address leading 0s")
99a52450c707 ("ARM: dts: imx7d-pico: Add Wifi support")
9daee3076940 ("ARM: dts: imx6q: Add Engicam i.CoreM6 DualLite/Solo initial support") a58d73340b0e ("ARM: dts: armada-385-synology-ds116: add support for Synology DS116 NAS") c201369d4aa5 ("ARM: dts: imx6ull: add imx6ull support")
d9e246cc2880 ("ARM: dts: imx6sx-sabreauto: add PMIC support") fc48e76489fd ("ARM: dts: imx6: Add support for Toradex Colibri iMX6 module")

How should we proceed with this patch?

--
Thanks,
Sasha

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#3 lore raw
Quoted 9 lines · Sasha Levin

Hi,

[This is an automated email]

This commit has been processed because it contains a -stable tag. The stable tag indicates that it's relevant for the following trees: 4.9+

The bot has tested the following trees: v5.0.5, v4.19.32, v4.14.109, v4.9.166.

Support for the LogicPD i.MX6QD EVM wasn't added until recently. I would expect it's OK to ignore it. It's not present in anything older than 5.1-RCx

adam

Quoted 57 lines

v5.0.5: Failed to apply! Possible dependencies:
1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM")

v4.19.32: Failed to apply! Possible dependencies:
1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM") 29988e867cb1 ("ARM: dts: imx7: Fix memory node duplication") 4edbe6aa46d1 ("ARM: dts: imx7d-pico-pi: Move SoM related part to imx7d-pico.dtsi") 50536c661194 ("ARM: dts: imx7d-pico: Do not harcode the memory size")

v4.14.109: Failed to apply! Possible dependencies:
1bf52b98ae1c ("ARM: dts: imx6sx-sabreauto: add external 24MHz clock source") 1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM") 221aaa198e70 ("ARM: dts: imx6sx-sabreauto: drop board specific pinctrl container node") 37accf72e04b ("ARM: dts: imx6sx-sabreauto: add fec support") 41bbeadceb03 ("ARM: dts: imx7d-pico-pi: Separate into cpu and baseboard dts") 4edbe6aa46d1 ("ARM: dts: imx7d-pico-pi: Move SoM related part to imx7d-pico.dtsi") 76dc340e7585 ("ARM: dts: imx6qdl: SolidRun: move AR8035 into microsom") 8dccafaa281a ("arm: dts: fix unit-address leading 0s")
99a52450c707 ("ARM: dts: imx7d-pico: Add Wifi support")
d9e246cc2880 ("ARM: dts: imx6sx-sabreauto: add PMIC support")

v4.9.166: Failed to apply! Possible dependencies:
12de44f55dcd ("ARM: dts: imx: Fix Ethernet PHY reset polarity") 1317efa1699f ("ARM: dts: imx6ul: Add DTS for liteSOM module") 13283626c889 ("ARM: dts: imx/vf: Correct license text")
1bf52b98ae1c ("ARM: dts: imx6sx-sabreauto: add external 24MHz clock source") 1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM") 221aaa198e70 ("ARM: dts: imx6sx-sabreauto: drop board specific pinctrl container node") 23c787a99ff7 ("ARM: dts: imx7d-pico: Add initial support")
26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia")
37accf72e04b ("ARM: dts: imx6sx-sabreauto: add fec support")
3faa1bb2e89c ("ARM: dts: imx: add Boundary Devices Nitrogen6_SOM2 support") 41bbeadceb03 ("ARM: dts: imx7d-pico-pi: Separate into cpu and baseboard dts") 478c9440b328 ("ARM: dts: imx6ul: Add DTS for liteBoard")
4edbe6aa46d1 ("ARM: dts: imx7d-pico-pi: Move SoM related part to imx7d-pico.dtsi") 6df11287f7c9 ("ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual initial support") 76dc340e7585 ("ARM: dts: imx6qdl: SolidRun: move AR8035 into microsom") 8dccafaa281a ("arm: dts: fix unit-address leading 0s")
99a52450c707 ("ARM: dts: imx7d-pico: Add Wifi support")
9daee3076940 ("ARM: dts: imx6q: Add Engicam i.CoreM6 DualLite/Solo initial support") a58d73340b0e ("ARM: dts: armada-385-synology-ds116: add support for Synology DS116 NAS") c201369d4aa5 ("ARM: dts: imx6ull: add imx6ull support")
d9e246cc2880 ("ARM: dts: imx6sx-sabreauto: add PMIC support") fc48e76489fd ("ARM: dts: imx6: Add support for Toradex Colibri iMX6 module")

How should we proceed with this patch?

--
Thanks,
Sasha

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

author reviewer
#4 lore raw
Quoted 3 lines · Adam Ford

Support for the LogicPD i.MX6QD EVM wasn't added until recently. I would expect it's OK to ignore it. It's not present in anything older than 5.1-RCx

Shawn, maybe you could drop the CC: stable line, so that this patch gets applied only for 5.1-rc.

After it reaches mainline, I can then manually adapt it for the older stable trees.

Thanks