Skip to contentSkip to conversation

tty/serial: atmel: Add is_half_duplex helper

PATCH New Razvan Stefanescu 1 participant 2 messages Apr 3, 2019

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 tty/serial: atmel: Add is_half_duplex helper

commit f3040983132b ("tty/serial: atmel: Add is_half_duplex helper") upstream.

Use a helper function to check that a port needs to use half duplex communication, replacing several occurrences of multi-line bit checking.

Fixes b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done")
Cc stable <[email protected]>
---
 drivers/tty/serial/atmel_serial.c | 18 ++++++++++--------
 1 file changed, 10 insertions(+), 8 deletions(-)
drivers/tty/serial/atmel_serial.c +10 -8
index d8e1945cb627..cfc2f2b7736e 100644
@@ -241,6 +241,12 @@ static inline void atmel_uart_write_char(struct uart_port *port, u8 value)
 
 #endif
 
+static inline int atmel_uart_is_half_duplex(struct uart_port *port)
+{
+	return (port->rs485.flags & SER_RS485_ENABLED) &&
+		!(port->rs485.flags & SER_RS485_RX_DURING_TX);
+}
+
 #ifdef CONFIG_SERIAL_ATMEL_PDC
 static bool atmel_use_pdc_rx(struct uart_port *port)
 {
@@ -492,8 +498,7 @@ static void atmel_stop_tx(struct uart_port *port)
 	/* Disable interrupts */
 	atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
 
-	if ((port->rs485.flags & SER_RS485_ENABLED) &&
-	    !(port->rs485.flags & SER_RS485_RX_DURING_TX))
+	if (atmel_uart_is_half_duplex(port))
 		atmel_start_rx(port);
 }
 
@@ -511,8 +516,7 @@ static void atmel_start_tx(struct uart_port *port)
 		return;
 
 	if (atmel_use_pdc_tx(port) || atmel_use_dma_tx(port))
-		if ((port->rs485.flags & SER_RS485_ENABLED) &&
-		    !(port->rs485.flags & SER_RS485_RX_DURING_TX))
+		if (atmel_uart_is_half_duplex(port))
 			atmel_stop_rx(port);
 
 	if (atmel_use_pdc_tx(port))
@@ -809,8 +813,7 @@ static void atmel_complete_tx_dma(void *arg)
 	 */
 	if (!uart_circ_empty(xmit))
 		atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
-	else if ((port->rs485.flags & SER_RS485_ENABLED) &&
-		 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
+	else if (atmel_uart_is_half_duplex(port)) {
 		/* DMA done, stop TX, start RX for RS485 */
 		atmel_start_rx(port);
 	}
@@ -1386,8 +1389,7 @@ static void atmel_tx_pdc(struct uart_port *port)
 		atmel_uart_writel(port, ATMEL_US_IER,
 				  atmel_port->tx_done_mask);
 	} else {
-		if ((port->rs485.flags & SER_RS485_ENABLED) &&
-		    !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
+		if (atmel_uart_is_half_duplex(port)) {
 			/* DMA done, stop TX, start RX for RS485 */
 			atmel_start_rx(port);
 		}
Signature · 1 line
2.19.1
#1 lore raw

PATCH 2/2 tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped

commit 69646d7a3689 ("tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped") upstream.

In half-duplex operation, RX should be started after TX completes.

If DMA is used, there is a case when the DMA transfer completes but the TX FIFO is not emptied, so the RX cannot be restarted just yet.

Use a boolean variable to store this state and rearm TX interrupt mask to be signaled again that the transfer finished. In interrupt transmit handler this variable is used to start RX. A warning message is generated if RX is activated before TX fifo is cleared.

Fixes b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done")
Cc stable <[email protected]>
---
 drivers/tty/serial/atmel_serial.c | 24 +++++++++++++++++++++---
 1 file changed, 21 insertions(+), 3 deletions(-)
drivers/tty/serial/atmel_serial.c +21 -3
index cfc2f2b7736e..b9179c300f9b 100644
@@ -175,6 +175,8 @@ struct atmel_uart_port {
 	unsigned int		pending_status;
 	spinlock_t		lock_suspended;
 
+	bool			hd_start_rx;	/* can start RX during half-duplex operation */
+
 	int (*prepare_rx)(struct uart_port *port);
 	int (*prepare_tx)(struct uart_port *port);
 	void (*schedule_rx)(struct uart_port *port);
@@ -814,8 +816,13 @@ static void atmel_complete_tx_dma(void *arg)
 	if (!uart_circ_empty(xmit))
 		atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
 	else if (atmel_uart_is_half_duplex(port)) {
-		/* DMA done, stop TX, start RX for RS485 */
-		atmel_start_rx(port);
+		/*
+		 * DMA done, re-enable TXEMPTY and signal that we can stop
+		 * TX and start RX for RS485
+		 */
+		atmel_port->hd_start_rx = true;
+		atmel_uart_writel(port, ATMEL_US_IER,
+				  atmel_port->tx_done_mask);
 	}
 
 	spin_unlock_irqrestore(&port->lock, flags);
@@ -1260,9 +1267,20 @@ atmel_handle_transmit(struct uart_port *port, unsigned int pending)
 	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
 
 	if (pending & atmel_port->tx_done_mask) {
-		/* Either PDC or interrupt transmission */
 		atmel_uart_writel(port, ATMEL_US_IDR,
 				  atmel_port->tx_done_mask);
+
+		/* Start RX if flag was set and FIFO is empty */
+		if (atmel_port->hd_start_rx) {
+			if (!(atmel_uart_readl(port, ATMEL_US_CSR)
+					& ATMEL_US_TXEMPTY))
+				dev_warn(port->dev, "Should start RX, but TX fifo is not empty\n");
+
+			atmel_port->hd_start_rx = false;
+			atmel_start_rx(port);
+			return;
+		}
+
 		atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
 	}
 }
Signature · 1 line
2.19.1