dt-binding: peci: add NPCM PECI documentation
Subsystems (4)
Tomer Maimon
maintainerPATCH 1/4 dt-binding: peci: add NPCM PECI documentation
Added device tree binding documentation for Nuvoton BMC NPCM Platform Environment Control Interface(PECI).
Signed-off-by Tomer Maimon <[email protected]>
--- .../devicetree/bindings/peci/peci-npcm.txt | 38 ++++++++++++++++++++++ 1 file changed, 38 insertions(+) create mode 100644 Documentation/devicetree/bindings/peci/peci-npcm.txt
Documentation/devicetree/bindings/peci/peci-npcm.txt new file +38 -0
@@ -0,0 +1,38 @@ +Nuvoton NPCM Platform Environment Control Interface (PECI) bus + +Required properties: +- compatible : "nuvoton,npcm750-peci" for the NPCM7XX BMC. +- reg : specifies PECI physical base address and size of the registers. +- #address-cells : Should be <1> required to define a client address. +- #size-cells : Should be <0> required to define a client address. +- interrupts : Contain the PECI interrupt with flags for falling edge. +- clocks : phandle of PECI reference clock. + +Optional properties: +- cmd-timeout-ms : Command timeout in units of ms. + 1 ~ 60000 (default: 1000) +- pull-down : Defines the PECI I/O internal pull down operation. + 0 - pull down always enable (default) + 1 - pull down only during transactions. + 2 - pull down always disable. +- host-neg-bit-rate : Define host negotiation bit rate divider. + the host negotiation bit rate calculate with formula: + clock frequency[Hz] / [4 x {host-neg-bit-rate + 1}] + 7 ~ 31 (default: 15) +- high-volt-range : Adapts PECI I/O interface to voltage range, the property + is a boolean parameter define as follow: + false - PECI I/O interface voltage range of 0.8-1.06V. (default) + true - PECI I/O interface voltage range of 0.95-1.26V. + +Example: + peci: peci-bus@100000 { + compatible = "nuvoton,npcm750-peci"; + reg = <0x100000 0x200>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk NPCM7XX_CLK_APB3>; + cmd-timeout-ms = <1000>; + pull-down = <0>; + host-neg-bit-rate = <15>; + };
Signature · 1 line
2.14.1
Tomer Maimon
maintainerPATCH 2/4 peci: npcm: add NPCM PECI driver
Add Nuvoton NPCM BMC Platform Environment
Control Interface(PECI) driver.
Signed-off-by Tomer Maimon <[email protected]>
--- drivers/peci/Kconfig | 11 ++ drivers/peci/Makefile | 1 + drivers/peci/peci-npcm.c | 410 +++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 422 insertions(+) create mode 100644 drivers/peci/peci-npcm.c
drivers/peci/Kconfig +11 -0
@@ -34,6 +34,17 @@ config PECI_ASPEED This support is also available as a module. If so, the module will be called peci-aspeed. +config PECI_NPCM + tristate "Nuvoton NPCM PECI support" + select REGMAP_MMIO + depends on OF + depends on ARCH_NPCM || COMPILE_TEST + help + Say Y here if you want support for the Platform Environment Control + Interface (PECI) bus adapter driver on the Nuvoton NPCM SoCs. + + This support is also available as a module. If so, the module + will be called peci-npcm. endmenu endif # PECI
drivers/peci/Makefile +1 -0
@@ -7,3 +7,4 @@ obj-$(CONFIG_PECI) += peci-core.o # Hardware specific bus drivers obj-$(CONFIG_PECI_ASPEED) += peci-aspeed.o +obj-$(CONFIG_PECI_NPCM) += peci-npcm.o
drivers/peci/peci-npcm.c new file +410 -0
410 lines not on this page · raw message
Signature · 1 line
2.14.1
Tomer Maimon
maintainerPATCH 3/4 dts: npcm7xx: add PECI support to NPCM7xx device tree
In reply to Tomer MaimonSigned-off-by Tomer Maimon <[email protected]>
--- arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi | 10 ++++++++++ arch/arm/boot/dts/nuvoton-npcm750-evb.dts | 12 ++++++++++++ 2 files changed, 22 insertions(+)
arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi +10 -0
@@ -341,6 +341,16 @@ }; }; + peci: peci-bus@100000 { + compatible = "nuvoton,npcm750-peci"; + reg = <0x100000 0x200>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk NPCM7XX_CLK_APB3>; + status = "disabled"; + }; + spi0: spi@200000 { compatible = "nuvoton,npcm750-pspi"; reg = <0x200000 0x1000>;
arch/arm/boot/dts/nuvoton-npcm750-evb.dts +12 -0
@@ -492,6 +492,18 @@ }; }; + peci: peci-bus@100000 { + cmd-timeout-ms = <1000>; + pull-down = <0>; + host-neg-bit-rate = <15>; + status = "okay"; + intel-peci-dimmtemp@30 { + compatible = "intel,peci-client"; + reg = <0x30>; + status = "okay"; + }; + }; + spi0: spi@200000 { cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; status = "okay";
Signature · 1 line
2.14.1
Tomer Maimon
maintainerPATCH 4/4 config: npcm7xx: add PECI support to npcm7xx defconfig
In reply to Tomer MaimonSigned-off-by Tomer Maimon <[email protected]>
--- arch/arm/configs/npcm7xx_defconfig | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/configs/npcm7xx_defconfig +5 -0
@@ -120,3 +120,8 @@ CONFIG_CRYPTO_LZO=y CONFIG_CRYPTO_USER_API_SKCIPHER=y CONFIG_CRYPTO_DEV_NPCMX50=y CONFIG_ARM_CRYPTO=y +CONFIG_PECI=y +CONFIG_PECI_NPCM=y +CONFIG_MFD_INTEL_PECI_CLIENT=y +CONFIG_SENSORS_PECI_CPUTEMP=y +CONFIG_SENSORS_PECI_DIMMTEMP=y
Signature · 1 line
2.14.1