Skip to contentSkip to conversation

igb: Debugging for setting rate negotiation settings.

PATCH New [email protected] 2 participants 3 messages Apr 2, 2019 – Apr 5, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 igb: Debugging for setting rate negotiation settings.

From: Ben Greear <[email protected]>

I found this useful while debugging an issue setting igb to fixed rates.

---
 drivers/net/ethernet/intel/igb/igb_main.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)
drivers/net/ethernet/intel/igb/igb_main.c +14 -2
index 350a2f120fc4..0f86b4eb5e30 100644
@@ -8711,8 +8711,11 @@ int igb_set_spd_dplx(struct igb_adapter *adapter, u32 spd, u8 dplx)
 	/* Make sure dplx is at most 1 bit and lsb of speed is not set
 	 * for the switch() below to work
 	 */
-	if ((spd & 1) || (dplx & ~1))
+	if ((spd & 1) || (dplx & ~1)) {
+		dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration, bit-mismatch, spd: 0x%x  dplx: 0x%x\n",
+			spd, dplx);
 		goto err_inval;
+	}
 
 	/* Fiber NIC's only allow 1000 gbps Full duplex
 	 * and 100Mbps Full duplex for 100baseFx sfp
@@ -8722,6 +8725,8 @@ int igb_set_spd_dplx(struct igb_adapter *adapter, u32 spd, u8 dplx)
 		case SPEED_10 + DUPLEX_HALF:
 		case SPEED_10 + DUPLEX_FULL:
 		case SPEED_100 + DUPLEX_HALF:
+			dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration, fiber does not support HD, spd: 0x%x  dplx: 0x%x\n",
+				spd, dplx);
 			goto err_inval;
 		default:
 			break;
@@ -8746,17 +8751,24 @@ int igb_set_spd_dplx(struct igb_adapter *adapter, u32 spd, u8 dplx)
 		adapter->hw.phy.autoneg_advertised = ADVERTISE_1000_FULL;
 		break;
 	case SPEED_1000 + DUPLEX_HALF: /* not supported */
+		dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration:  1Gbps HD not supported\n",
+			spd, dplx);
+		goto err_inval;
 	default:
+		dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration, case not handled, spd: 0x%x  dplx: 0x%x\n",
+			spd, dplx);
 		goto err_inval;
 	}
 
+	dev_info(&pdev->dev, "Set Speed: %d  dplx: %d  autoneg: %d  forced-speed-duplex: %d\n",
+		 spd, dplx, mac->autoneg, mac->forced_speed_duplex);
+
 	/* clear MDI, MDI(-X) override is only allowed when autoneg enabled */
 	adapter->hw.phy.mdix = AUTO_ALL_MODES;
 
 	return 0;
 
 err_inval:
-	dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration\n");
 	return -EINVAL;
 }
 
Signature · 1 line
2.20.1
#1 lore raw
Thank you for the patch! Perhaps something to improve:

Hi,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on jkirsher-next-queue/dev-queue]
[also build test WARNING on v5.1-rc3 next-20190404]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]

url:    https://github.com/0day-ci/linux/commits/greearb-candelatech-com/igb-Debugging-for-setting-rate-negotiation-settings/20190405-090219
base:   https://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue.git dev-queue
config: x86_64-lkp (attached as .config)
compiler: gcc-7 (Debian 7.3.0-1) 7.3.0
reproduce:
        # save the attached .config to linux build tree
        make ARCH=x86_64 

All warnings (new ones prefixed by >>):

In file included from include/linux/dma-mapping.h:7:0,
from include/linux/skbuff.h:34,
from include/linux/if_ether.h:23,
from include/uapi/linux/ethtool.h:19,
from include/linux/ethtool.h:18,
from include/linux/netdevice.h:41,
from drivers/net/ethernet/intel/igb/igb_main.c:12:
drivers/net/ethernet/intel/igb/igb_main.c: In function 'igb_set_spd_dplx':

>> drivers/net/ethernet/intel/igb/igb_main.c:8730:23: warning: too many arguments for format [-Wformat-extra-args]
      dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration:  1Gbps HD not supported\n",
                          ^
   include/linux/device.h:1402:22: note: in definition of macro 'dev_fmt'
    #define dev_fmt(fmt) fmt
                         ^~~
   drivers/net/ethernet/intel/igb/igb_main.c:8730:3: note: in expansion of macro 'dev_err'
      dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration:  1Gbps HD not supported\n",
      ^~~~~~~

vim +8730 drivers/net/ethernet/intel/igb/igb_main.c

8679
8680 int igb_set_spd_dplx(struct igb_adapter *adapter, u32 spd, u8 dplx)
8681 {
8682 struct pci_dev *pdev = adapter->pdev;
8683 struct e1000_mac_info *mac = &adapter->hw.mac;
8684
8685 mac->autoneg = 0;
8686
8687 /* Make sure dplx is at most 1 bit and lsb of speed is not set
8688 * for the switch() below to work
8689 */
8690 if ((spd & 1) || (dplx & ~1)) {
8691 dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration, bit-mismatch, spd: 0x%x dplx: 0x%x\n",
8692 spd, dplx);
8693 goto err_inval;
8694 }
8695
8696 /* Fiber NIC's only allow 1000 gbps Full duplex
8697 * and 100Mbps Full duplex for 100baseFx sfp
8698 */
8699 if (adapter->hw.phy.media_type == e1000_media_type_internal_serdes) {
8700 switch (spd + dplx) {
8701 case SPEED_10 + DUPLEX_HALF:
8702 case SPEED_10 + DUPLEX_FULL:
8703 case SPEED_100 + DUPLEX_HALF:
8704 dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration, fiber does not support HD, spd: 0x%x dplx: 0x%x\n",
8705 spd, dplx);
8706 goto err_inval;
8707 default:
8708 break;
8709 }
8710 }
8711
8712 switch (spd + dplx) {
8713 case SPEED_10 + DUPLEX_HALF:
8714 mac->forced_speed_duplex = ADVERTISE_10_HALF;
8715 break;
8716 case SPEED_10 + DUPLEX_FULL:
8717 mac->forced_speed_duplex = ADVERTISE_10_FULL;
8718 break;
8719 case SPEED_100 + DUPLEX_HALF:
8720 mac->forced_speed_duplex = ADVERTISE_100_HALF;
8721 break;
8722 case SPEED_100 + DUPLEX_FULL:
8723 mac->forced_speed_duplex = ADVERTISE_100_FULL;
8724 break;
8725 case SPEED_1000 + DUPLEX_FULL:
8726 mac->autoneg = 1;
8727 adapter->hw.phy.autoneg_advertised = ADVERTISE_1000_FULL;
8728 break;
8729 case SPEED_1000 + DUPLEX_HALF: /* not supported */

> 8730			dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration:  1Gbps HD not supported\n",

8731 spd, dplx);
8732 goto err_inval;
8733 default:
8734 dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration, case not handled, spd: 0x%x dplx: 0x%x\n",
8735 spd, dplx);
8736 goto err_inval;
8737 }
8738
8739 dev_info(&pdev->dev, "Set Speed: %d dplx: %d autoneg: %d forced-speed-duplex: %d\n",
8740 spd, dplx, mac->autoneg, mac->forced_speed_duplex);
8741
8742 /* clear MDI, MDI(-X) override is only allowed when autoneg enabled */
8743 adapter->hw.phy.mdix = AUTO_ALL_MODES;
8744
8745 return 0;
8746
8747 err_inval:
8748 return -EINVAL;
8749 }
8750

---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation

#2 lore raw
In reply to [email protected]
Thank you for the patch! Perhaps something to improve:

Hi,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on jkirsher-next-queue/dev-queue]
[also build test WARNING on v5.1-rc3 next-20190404]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]

url:    https://github.com/0day-ci/linux/commits/greearb-candelatech-com/igb-Debugging-for-setting-rate-negotiation-settings/20190405-090219
base:   https://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue.git dev-queue
config: x86_64-kexec (attached as .config)
compiler: gcc-7 (Debian 7.3.0-1) 7.3.0
reproduce:
        # save the attached .config to linux build tree
        make ARCH=x86_64 

All warnings (new ones prefixed by >>):

In file included from include/linux/dma-mapping.h:7:0,
from include/linux/skbuff.h:34,
from include/linux/if_ether.h:23,
from include/uapi/linux/ethtool.h:19,
from include/linux/ethtool.h:18,
from include/linux/netdevice.h:41,
from drivers/net//ethernet/intel/igb/igb_main.c:12:
drivers/net//ethernet/intel/igb/igb_main.c: In function 'igb_set_spd_dplx':
drivers/net//ethernet/intel/igb/igb_main.c:8730:23: warning: too many arguments for format [-Wformat-extra-args]

      dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration:  1Gbps HD not supported\n",
                          ^
   include/linux/device.h:1402:22: note: in definition of macro 'dev_fmt'
    #define dev_fmt(fmt) fmt
                         ^~~
>> drivers/net//ethernet/intel/igb/igb_main.c:8730:3: note: in expansion of macro 'dev_err'
      dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration:  1Gbps HD not supported\n",
      ^~~~~~~

vim +/dev_err +8730 drivers/net//ethernet/intel/igb/igb_main.c

8679
8680 int igb_set_spd_dplx(struct igb_adapter *adapter, u32 spd, u8 dplx)
8681 {
8682 struct pci_dev *pdev = adapter->pdev;
8683 struct e1000_mac_info *mac = &adapter->hw.mac;
8684
8685 mac->autoneg = 0;
8686
8687 /* Make sure dplx is at most 1 bit and lsb of speed is not set
8688 * for the switch() below to work
8689 */
8690 if ((spd & 1) || (dplx & ~1)) {
8691 dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration, bit-mismatch, spd: 0x%x dplx: 0x%x\n",
8692 spd, dplx);
8693 goto err_inval;
8694 }
8695
8696 /* Fiber NIC's only allow 1000 gbps Full duplex
8697 * and 100Mbps Full duplex for 100baseFx sfp
8698 */
8699 if (adapter->hw.phy.media_type == e1000_media_type_internal_serdes) {
8700 switch (spd + dplx) {
8701 case SPEED_10 + DUPLEX_HALF:
8702 case SPEED_10 + DUPLEX_FULL:
8703 case SPEED_100 + DUPLEX_HALF:
8704 dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration, fiber does not support HD, spd: 0x%x dplx: 0x%x\n",
8705 spd, dplx);
8706 goto err_inval;
8707 default:
8708 break;
8709 }
8710 }
8711
8712 switch (spd + dplx) {
8713 case SPEED_10 + DUPLEX_HALF:
8714 mac->forced_speed_duplex = ADVERTISE_10_HALF;
8715 break;
8716 case SPEED_10 + DUPLEX_FULL:
8717 mac->forced_speed_duplex = ADVERTISE_10_FULL;
8718 break;
8719 case SPEED_100 + DUPLEX_HALF:
8720 mac->forced_speed_duplex = ADVERTISE_100_HALF;
8721 break;
8722 case SPEED_100 + DUPLEX_FULL:
8723 mac->forced_speed_duplex = ADVERTISE_100_FULL;
8724 break;
8725 case SPEED_1000 + DUPLEX_FULL:
8726 mac->autoneg = 1;
8727 adapter->hw.phy.autoneg_advertised = ADVERTISE_1000_FULL;
8728 break;
8729 case SPEED_1000 + DUPLEX_HALF: /* not supported */

> 8730			dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration:  1Gbps HD not supported\n",

8731 spd, dplx);
8732 goto err_inval;
8733 default:
8734 dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration, case not handled, spd: 0x%x dplx: 0x%x\n",
8735 spd, dplx);
8736 goto err_inval;
8737 }
8738
8739 dev_info(&pdev->dev, "Set Speed: %d dplx: %d autoneg: %d forced-speed-duplex: %d\n",
8740 spd, dplx, mac->autoneg, mac->forced_speed_duplex);
8741
8742 /* clear MDI, MDI(-X) override is only allowed when autoneg enabled */
8743 adapter->hw.phy.mdix = AUTO_ALL_MODES;
8744
8745 return 0;
8746
8747 err_inval:
8748 return -EINVAL;
8749 }
8750

---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation