arm64: allwinner: h6: orangepi: Add PIO regulators
Subsystems (2)
PATCH v2 1/5 arm64: allwinner: h6: orangepi: Add PIO regulators
OrangePi One Plus and OrangePi Lite2 use the same PIO regulators.
Add this in the common device tree.
--- arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +11 -0
@@ -72,6 +72,12 @@ status = "okay"; }; +&pio { + vcc-pc-supply = <®_bldo2>; + vcc-pd-supply = <®_cldo1>; + vcc-pg-supply = <®_bldo3>; +}; + &r_i2c { status = "okay";
@@ -191,6 +197,11 @@ }; }; +&r_pio { + vcc-pl-supply = <®_aldo1>; + vcc-pm-supply = <®_bldo3>; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>;
Signature · 1 line
2.17.1
PATCH v2 2/5 arm64: dts: allwinner: h6: pine64: Add PIO regulators
Add PIO regulators for Pine64 board.
--- arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts +11 -0
@@ -131,6 +131,12 @@ status = "okay"; }; +&pio { + vcc-pc-supply = <®_bldo2>; + vcc-pd-supply = <®_cldo1>; + vcc-pg-supply = <®_bldo2>; +}; + &r_i2c { status = "okay";
@@ -251,6 +257,11 @@ }; }; +&r_pio { + vcc-pl-supply = <®_aldo1>; + vcc-pm-supply = <®_bldo2>; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>;
Signature · 7 lines
2.17.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v2 3/5 arm64: dts: allwinner: h6: move MMC pinctrl to dtsi
In reply to Clément PéronThere is only one pinmuxing available for each MMC controller.
Move the pinctrl to the SOC
--- arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi | 2 -- arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts | 4 ---- arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 4 ++++ 3 files changed, 4 insertions(+), 6 deletions(-)
arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +0 -2
@@ -56,8 +56,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_cldo1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; bus-width = <4>;
arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts +0 -4
@@ -104,8 +104,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_cldo1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; bus-width = <4>;
@@ -113,8 +111,6 @@ }; &mmc2 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc2_pins>; vmmc-supply = <®_cldo1>; vqmmc-supply = <®_bldo2>; non-removable;
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +4 -0
@@ -273,6 +273,8 @@ resets = <&ccu RST_BUS_MMC0>; reset-names = "ahb"; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; status = "disabled"; #address-cells = <1>; #size-cells = <0>;
@@ -301,6 +303,8 @@ resets = <&ccu RST_BUS_MMC2>; reset-names = "ahb"; interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; status = "disabled"; #address-cells = <1>; #size-cells = <0>;
Signature · 1 line
2.17.1
PATCH v2 4/5 dt-bindings: vendor-prefixes: add AZW
In reply to Clément PéronShenzhen AZW Technology Co. Ltd. is a manufacturer specialized in Android smart TV boxes, Intel mini PCs and home cloud TV boxes with NAS.
Add the vendor prefix for AZW.
--- Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
@@ -54,6 +54,7 @@ avic Shanghai AVIC Optoelectronics Co., Ltd. avnet Avnet, Inc. axentia Axentia Technologies AB axis Axis Communications AB +azw Shenzhen AZW Technology Co., Ltd. bananapi BIPAI KEJI LIMITED bhf Beckhoff Automation GmbH & Co. KG bitmain Bitmain Technologies
Signature · 1 line
2.17.1
Re: [PATCH v2 4/5] dt-bindings: vendor-prefixes: add AZW
Quoted 4 lines · Clément Péron
Shenzhen AZW Technology Co. Ltd. is a manufacturer specialized in Android smart TV boxes, Intel mini PCs and home cloud TV boxes with NAS.
Add the vendor prefix for AZW.
Yay, I've been hacking on a Beelink A1 so this will be one less patch to worry about if I ever get it finished enough to upstream :)
(I had picked "beelink" as a prefix, but I guess "azw" does seem more appropriate to cover their OEM stuff as well, so there's no good reason to treat the in-house brand specially)
Quoted 18 lines
Signed-off-by Clément Péron <[email protected]>--- Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+)Documentation/devicetree/bindings/vendor-prefixes.txt +1
-0@@ -54,6 +54,7 @@ avic Shanghai AVIC Optoelectronics Co., Ltd. avnet Avnet, Inc. axentia Axentia Technologies AB axis Axis Communications AB +azw Shenzhen AZW Technology Co., Ltd. bananapi BIPAI KEJI LIMITED bhf Beckhoff Automation GmbH & Co. KG bitmain Bitmain Technologies
PATCH v2 5/5 ARM: dts: sun50i: h6: Introduce Beelink GS1 board
In reply to Clément PéronBeelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply
---
Thanks to Jagan and Icenowy, most of this devicetree is taken from their works on the OrangePi One Plus and Pine H64.
Changes in v2 (Thanks to Maxime Ripard):
- move MMC pinctrl to SOC dtsi
- add board to Sunxi YAML file
- add PIO/R_PIO regulators
- remove always_on from SDIO regulators
.../devicetree/bindings/arm/sunxi.yaml | 5 + arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-h6-beelink-gs1.dts | 256 ++++++++++++++++++ 3 files changed, 262 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
Documentation/devicetree/bindings/arm/sunxi.yaml +5 -0
@@ -136,6 +136,11 @@ properties: - const: lemaker,bananapro - const: allwinner,sun7i-a20 + - description: Beelink GS1 + items: + - const: azw,beelink-gs1 + - const: allwinner,sun50i-h6 + - description: Beelink X2 items: - const: roofull,beelink-x2
arch/arm64/boot/dts/allwinner/Makefile +1 -0
@@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +256 -0
256 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [PATCH v2 5/5] ARM: dts: sun50i: h6: Introduce Beelink GS1 board
Hi,
Adding this r_pio regulators make a new error in the bootlog :
[ 0.346843] sun50i-h6-r-pinctrl 7022000.pinctrl: Couldn't get bank PL regulator [ 0.346853] sun50i-h6-r-pinctrl 7022000.pinctrl: request() failed for pin 352 [ 0.346862] sun50i-h6-r-pinctrl 7022000.pinctrl: pin-352 (7081400.i2c) status -517 [ 0.346871] sun50i-h6-r-pinctrl 7022000.pinctrl: could not request pin 352 (PL0) from group PL0 on device 7022000.pinctrl [ 0.346878] mv64xxx_i2c 7081400.i2c: Error applying setting,
reverse things back
PL0 and PL1 are SCK/SDA for the PMIC :(
Clement
Quoted 327 lines · Clément Péron
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supplySigned-off-by Clément Péron <[email protected]>---
Thanks to Jagan and Icenowy, most of this devicetree is taken from their works on the OrangePi One Plus and Pine H64.
Changes in v2 (Thanks to Maxime Ripard):
- move MMC pinctrl to SOC dtsi
- add board to Sunxi YAML file
- add PIO/R_PIO regulators
- removealways_onfrom SDIO regulators.../devicetree/bindings/arm/sunxi.yaml | 5 + arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-h6-beelink-gs1.dts | 256 ++++++++++++++++++ 3 files changed, 262 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dtsDocumentation/devicetree/bindings/arm/sunxi.yaml +5
-0@@ -136,6 +136,11 @@ properties: - const: lemaker,bananapro - const: allwinner,sun7i-a20 + - description: Beelink GS1 + items: + - const: azw,beelink-gs1 + - const: allwinner,sun50i-h6 + - description: Beelink X2 items: - const: roofull,beelink-x2arch/arm64/boot/dts/allwinner/Makefile +1
-0@@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtbarch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +256
-1@@ -0,0 +1,256 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2019 Clément Péron <[email protected]> + */ + +/dts-v1/; + +#include "sun50i-h6.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Beelink GS1"; + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6"; + + aliases { + ethernet0 = &emac; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + power { + label = "beelink:white:power"; + gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ + default-state = "on"; + }; + }; + + reg_vcc5v: vcc5v { + /* board wide 5V supply directly from the DC jack */ + compatible = "regulator-fixed"; + regulator-name = "vcc-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&ext_rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_aldo2>; + allwinner,rx-delay-ps = <0>; + allwinner,tx-delay-ps = <0>; + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&mmc0 { + vmmc-supply = <®_cldo1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + vmmc-supply = <®_cldo1>; + vqmmc-supply = <®_bldo2>; + non-removable; + cap-mmc-hw-reset; + bus-width = <8>; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&pio { + vcc-pd-supply = <®_cldo1>; + vcc-pg-supply = <®_aldo1>; +}; + +&r_i2c { + status = "okay"; + + axp805: pmic@36 { + compatible = "x-powers,axp805", "x-powers,axp806"; + reg = <0x36>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + x-powers,self-working-mode; + vina-supply = <®_vcc5v>; + vinb-supply = <®_vcc5v>; + vinc-supply = <®_vcc5v>; + vind-supply = <®_vcc5v>; + vine-supply = <®_vcc5v>; + aldoin-supply = <®_vcc5v>; + bldoin-supply = <®_vcc5v>; + cldoin-supply = <®_vcc5v>; + + regulators { + reg_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pl"; + }; + + reg_aldo2: aldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-ac200"; + regulator-enable-ramp-delay = <100000>; + }; + + reg_aldo3: aldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc25-dram"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-bias-pll"; + }; + + reg_bldo2: bldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-efuse-pcie-hdmi-io"; + }; + + reg_bldo3: bldo3 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-dcxoio"; + }; + + bldo4 { + /* unused */ + }; + + reg_cldo1: cldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; + }; + + reg_cldo2: cldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-1"; + }; + + reg_cldo3: cldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-2"; + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdcc: dcdcc { + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-gpu"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <960000>; + regulator-max-microvolt = <960000>; + regulator-name = "vdd-sys"; + }; + + reg_dcdce: dcdce { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; + }; + + sw { + /* unused */ + }; + }; + }; +}; + +&r_pio { + vcc-pl-supply = <®_aldo1>; + vcc-pm-supply = <®_aldo1>; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +}; + +&usb2otg { + dr_mode = "host"; + status = "okay"; +}; + +&usb2phy { + usb0_vbus-supply = <®_vcc5v>; + status = "okay"; +}; --2.17.1
Re: [PATCH v2 5/5] ARM: dts: sun50i: h6: Introduce Beelink GS1 board
Probing PMIC, Probe the PL0/1 Pins which Probe PL Bank power which Probe PMIC
Quoted 347 lines · Clément Péron
Hi,
Adding this
r_pioregulators make a new error in the bootlog :[ 0.346843] sun50i-h6-r-pinctrl 7022000.pinctrl: Couldn't get bank PL regulator [ 0.346853] sun50i-h6-r-pinctrl 7022000.pinctrl: request() failed for pin 352 [ 0.346862] sun50i-h6-r-pinctrl 7022000.pinctrl: pin-352 (7081400.i2c) status -517 [ 0.346871] sun50i-h6-r-pinctrl 7022000.pinctrl: could not request pin 352 (PL0) from group PL0 on device 7022000.pinctrl [ 0.346878] mv64xxx_i2c 7081400.i2c: Error applying setting,reverse things back
PL0 and PL1 are SCK/SDA for the PMIC :(
Clement
Quoted 327 lines · Clément Péron
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supplySigned-off-by Clément Péron <[email protected]>---
Thanks to Jagan and Icenowy, most of this devicetree is taken from their works on the OrangePi One Plus and Pine H64.
Changes in v2 (Thanks to Maxime Ripard):
- move MMC pinctrl to SOC dtsi
- add board to Sunxi YAML file
- add PIO/R_PIO regulators
- removealways_onfrom SDIO regulators.../devicetree/bindings/arm/sunxi.yaml | 5 + arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-h6-beelink-gs1.dts | 256 ++++++++++++++++++ 3 files changed, 262 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dtsDocumentation/devicetree/bindings/arm/sunxi.yaml +5
-0@@ -136,6 +136,11 @@ properties: - const: lemaker,bananapro - const: allwinner,sun7i-a20 + - description: Beelink GS1 + items: + - const: azw,beelink-gs1 + - const: allwinner,sun50i-h6 + - description: Beelink X2 items: - const: roofull,beelink-x2arch/arm64/boot/dts/allwinner/Makefile +1
-0@@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtbarch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +256
-1@@ -0,0 +1,256 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2019 Clément Péron <[email protected]> + */ + +/dts-v1/; + +#include "sun50i-h6.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Beelink GS1"; + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6"; + + aliases { + ethernet0 = &emac; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + power { + label = "beelink:white:power"; + gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ + default-state = "on"; + }; + }; + + reg_vcc5v: vcc5v { + /* board wide 5V supply directly from the DC jack */ + compatible = "regulator-fixed"; + regulator-name = "vcc-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&ext_rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_aldo2>; + allwinner,rx-delay-ps = <0>; + allwinner,tx-delay-ps = <0>; + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&mmc0 { + vmmc-supply = <®_cldo1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + vmmc-supply = <®_cldo1>; + vqmmc-supply = <®_bldo2>; + non-removable; + cap-mmc-hw-reset; + bus-width = <8>; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&pio { + vcc-pd-supply = <®_cldo1>; + vcc-pg-supply = <®_aldo1>; +}; + +&r_i2c { + status = "okay"; + + axp805: pmic@36 { + compatible = "x-powers,axp805", "x-powers,axp806"; + reg = <0x36>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + x-powers,self-working-mode; + vina-supply = <®_vcc5v>; + vinb-supply = <®_vcc5v>; + vinc-supply = <®_vcc5v>; + vind-supply = <®_vcc5v>; + vine-supply = <®_vcc5v>; + aldoin-supply = <®_vcc5v>; + bldoin-supply = <®_vcc5v>; + cldoin-supply = <®_vcc5v>; + + regulators { + reg_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pl"; + }; + + reg_aldo2: aldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-ac200"; + regulator-enable-ramp-delay = <100000>; + }; + + reg_aldo3: aldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc25-dram"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-bias-pll"; + }; + + reg_bldo2: bldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-efuse-pcie-hdmi-io"; + }; + + reg_bldo3: bldo3 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-dcxoio"; + }; + + bldo4 { + /* unused */ + }; + + reg_cldo1: cldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; + }; + + reg_cldo2: cldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-1"; + }; + + reg_cldo3: cldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-2"; + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdcc: dcdcc { + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-gpu"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <960000>; + regulator-max-microvolt = <960000>; + regulator-name = "vdd-sys"; + }; + + reg_dcdce: dcdce { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; + }; + + sw { + /* unused */ + }; + }; + }; +}; + +&r_pio { + vcc-pl-supply = <®_aldo1>; + vcc-pm-supply = <®_aldo1>; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +}; + +&usb2otg { + dr_mode = "host"; + status = "okay"; +}; + +&usb2phy { + usb0_vbus-supply = <®_vcc5v>; + status = "okay"; +}; --2.17.1
Re: [PATCH v2 5/5] ARM: dts: sun50i: h6: Introduce Beelink GS1 board
In reply to Clément PéronQuoted 12 lines · Clément Péron
Hi,
Adding this
r_pioregulators make a new error in the bootlog :[ 0.346843] sun50i-h6-r-pinctrl 7022000.pinctrl: Couldn't get bank PL regulator [ 0.346853] sun50i-h6-r-pinctrl 7022000.pinctrl: request() failed for pin 352 [ 0.346862] sun50i-h6-r-pinctrl 7022000.pinctrl: pin-352 (7081400.i2c) status -517 [ 0.346871] sun50i-h6-r-pinctrl 7022000.pinctrl: could not request pin 352 (PL0) from group PL0 on device 7022000.pinctrl [ 0.346878] mv64xxx_i2c 7081400.i2c: Error applying setting,
Quoted 3 lines
reverse things back
PL0 and PL1 are SCK/SDA for the PMIC :(
How was this DT tested then?
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
Signature · 3 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected] For more options, visit https://groups.google.com/d/optout.
Re: [PATCH v2 5/5] ARM: dts: sun50i: h6: Introduce Beelink GS1 board
Hi,
Quoted 16 lines · Maxime Ripard
Quoted 14 lines · Clément Péron
Hi,
Adding this
r_pioregulators make a new error in the bootlog :[ 0.346843] sun50i-h6-r-pinctrl 7022000.pinctrl: Couldn't get bank PL regulator [ 0.346853] sun50i-h6-r-pinctrl 7022000.pinctrl: request() failed for pin 352 [ 0.346862] sun50i-h6-r-pinctrl 7022000.pinctrl: pin-352 (7081400.i2c) status -517 [ 0.346871] sun50i-h6-r-pinctrl 7022000.pinctrl: could not request pin 352 (PL0) from group PL0 on device 7022000.pinctrl [ 0.346878] mv64xxx_i2c 7081400.i2c: Error applying setting,reverse things back
Quoted 3 lines
Quoted 1 line
PL0 and PL1 are SCK/SDA for the PMIC :(
How was this DT tested then?
There was a mistake when I tested the patch v2 and only saw this after posting the patch.
Can I submit a V3 without pio / r_pio regulators ? (+ the yaml patch separated)
Thanks,
Quoted 7 lines
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
Re: [PATCH v2 5/5] ARM: dts: sun50i: h6: Introduce Beelink GS1 board
In reply to Clément PéronQuoted 38 lines · Clément Péron
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supplySigned-off-by Clément Péron <[email protected]>---
Thanks to Jagan and Icenowy, most of this devicetree is taken from their works on the OrangePi One Plus and Pine H64.
Changes in v2 (Thanks to Maxime Ripard):
- move MMC pinctrl to SOC dtsi
- add board to Sunxi YAML file
- add PIO/R_PIO regulators
- removealways_onfrom SDIO regulators.../devicetree/bindings/arm/sunxi.yaml | 5 + arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-h6-beelink-gs1.dts | 256 ++++++++++++++++++ 3 files changed, 262 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dtsDocumentation/devicetree/bindings/arm/sunxi.yaml +0
-0
Documentation/devicetree/bindings/arm/sunxi.yaml properties: · line 143
Quoted 8 lines
Documentation/devicetree/bindings/arm/sunxi.yaml +5
-0@@ -136,6 +136,11 @@ properties: - const: lemaker,bananapro - const: allwinner,sun7i-a20 + - description: Beelink GS1 + items: + - const: azw,beelink-gs1 + - const: allwinner,sun50i-h6 +
Can you make that a separate patch?
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
Signature · 3 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected] For more options, visit https://groups.google.com/d/optout.
Quoted 27 lines · Clément Péron
OrangePi One Plus and OrangePi Lite2 use the same PIO regulators.
Add this in the common device tree.
Signed-off-by Clément Péron <[email protected]>--- arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +6
-0@@ -72,6 +72,12 @@ status = "okay"; }; +&pio { + vcc-pc-supply = <®_bldo2>; + vcc-pd-supply = <®_cldo1>; + vcc-pg-supply = <®_bldo3>; +}; + &r_i2c { status = "okay";
arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi line 204
Quoted 8 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +5
-0@@ -191,6 +197,11 @@ }; }; +&r_pio { + vcc-pl-supply = <®_aldo1>; + vcc-pm-supply = <®_bldo3>; +}; +
How was this tested?
Please run checkpatch on your patches as well.
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
Hi,
Quoted 32 lines · Maxime Ripard
Quoted 30 lines · Clément Péron
OrangePi One Plus and OrangePi Lite2 use the same PIO regulators.
Add this in the common device tree.
Signed-off-by Clément Péron <[email protected]>--- arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +6
-0@@ -72,6 +72,12 @@ status = "okay"; }; +&pio { + vcc-pc-supply = <®_bldo2>; + vcc-pd-supply = <®_cldo1>; + vcc-pg-supply = <®_bldo3>; +}; + &r_i2c { status = "okay";@@ -191,6 +197,11 @@ }; };
Quoted 7 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi line 204
Quoted 5 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +5
-0+&r_pio { + vcc-pl-supply = <®_aldo1>; + vcc-pm-supply = <®_bldo3>; +}; +How was this tested?
Sorry maybe I should mention that but I don't own an OrangePi or a Pine H64.
But this should have the same issue than the Beelink GS1.
Quoted 2 lines
Please run checkpatch on your patches as well.
Thanks for the advice,
Clement
Quoted 7 lines
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com